Use the idr-interface rather than a static table to manage minor-number
allocations.
This allows us to easily switch over to fully dynamic minor allocations
when the TTY-layer can handle that.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Static checkers complain that the current condition is never true. It
seems pretty likely that it's a typo and "URB" was intended instead of
"USB".
Fixes: 3d97ff63f8 ('usbdevfs: Use scatter-gather lists for large bulk transfers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some EHCI controllers have a Transaction Translator built into
the root hub. Support this feature in device tree when using
the ehci-platform driver by adding a feature flag for it.
This is needed to get USB working on NXP LPC18xx/43xx platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make Freescale EHCI driver an independent entity from ehci-hcd.c.
This involves
- using module_init/module_exit functions
- using overrides structure
- some necessary code cleanup
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regression in commit 638139eb95 ("usb: hub: allow to process more usb
hub events in parallel")
The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.
This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to
commit 6fecd4f2a5 ("USB: separate usb_address0 mutexes for each bus")
With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.
Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.
Fixes multiple boot errors:
[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device
And:
[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device
And:
[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device
And:
[ 11.018386] usb 1-3: device descriptor read/all, error -110
And:
[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
Tested with 200 reboots, resulting in no USB hub init related errors.
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.com
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
[changed git commit description style for checkpatch -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed regression. After commit 29e409f0f7 ("xhci: Allow xHCI drivers to
be built as separate modules") the module xhci_hcd became non-removable.
That behaviour is not expected and there're no notes about it in commit
message. The module should be removable as it blocks PM suspend/resume
functions (Debian Bug#666406).
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the renesas_usbhs driver is enabled in ARM multi_v7_defconfig,
we now get a new warning:
renesas_usbhs/mod.c: In function 'usbhs_interrupt':
renesas_usbhs/mod.c:246:7: warning: 'intenb1' may be used uninitialized in this function [-Wmaybe-uninitialized]
gcc correctly points to a problem here, for the case that the
device is in host mode, we use the intenb1 variable without
having assigned it first. The state->intsts1 has a similar
problem, but gcc cannot know that.
This avoids the problem by initializing both sides of the
comparison to zero when we don't read them from the respective
registers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 88a25e02f3 ("usb: renesas_usbhs: Add access control for INTSTS1 and INTENB1 register")
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch uses the unique id to identify the type of external connector instead
of string name. The string name have the many potential issues. So, this patch
defines the 'extcon' enumeration which includes all supported external connector
on EXTCON subsystem. If new external connector is necessary, the unique id of
new connector have to be added in 'extcon' enumeration. There are current
supported external connector in 'enum extcon' as following:
enum extcon {
EXTCON_NONE = 0x0,
/* USB external connector */
EXTCON_USB = 0x1,
EXTCON_USB_HOST = 0x2,
/* Charger external connector */
EXTCON_TA = 0x10,
EXTCON_FAST_CHARGER = 0x11,
EXTCON_SLOW_CHARGER = 0x12,
EXTCON_CHARGE_DOWNSTREAM = 0x13,
/* Audio and video external connector */
EXTCON_LINE_IN = 0x20,
EXTCON_LINE_OUT = 0x21,
EXTCON_MICROPHONE = 0x22,
EXTCON_HEADPHONE = 0x23,
EXTCON_HDMI = 0x30,
EXTCON_MHL = 0x31,
EXTCON_DVI = 0x32,
EXTCON_VGA = 0x33,
EXTCON_SPDIF_IN = 0x34,
EXTCON_SPDIF_OUT = 0x35,
EXTCON_VIDEO_IN = 0x36,
EXTCON_VIDEO_OUT = 0x37,
/* Miscellaneous external connector */
EXTCON_DOCK = 0x50,
EXTCON_JIG = 0x51,
EXTCON_MECHANICAL = 0x52,
EXTCON_END,
};
For example in extcon-arizona.c:
To use unique id removes the potential issue about handling
the inconsistent name of external connector with string.
- Previously, use the string to register the type of arizona jack connector
static const char *arizona_cable[] = {
"Mechanical",
"Microphone",
"Headphone",
"Line-out",
};
- Newly, use the unique id to register the type of arizona jack connector
static const enum extcon arizona_cable[] = {
EXTCON_MECHANICAL,
EXTCON_MICROPHONE,
EXTCON_HEADPHONE,
EXTCON_LINE_OUT,
EXTCON_NONE,
};
And this patch modify the prototype of extcon_{get|set}_cable_state_() which
uses the 'enum extcon id' instead of 'cable_index'. Because although one more
extcon drivers support USB cable, each extcon driver might has the differnt
'cable_index' for USB cable. All extcon drivers can use the unique id number
for same external connector with modified extcon_{get|set}_cable_state_().
- Previously, use 'cable_index' on these functions:
extcon_get_cable_state_(struct extcon_dev*, int cable_index)
extcon_set_cable_state_(struct extcon_dev*, int cable_index, bool state)
-Newly, use 'enum extcon id' on these functions:
extcon_get_cable_state_(struct extcon_dev*, enum extcon id)
extcon_set_cable_state_(struct extcon_dev*, enum extcon id, bool state)
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[arnd: Report the build break about drivers/usb/phy/phy-tahvo.c after using the
unique id for external connector insteadf of string]
Reported-by: Arnd Bergmann <arnd@arndb.de>
[dan.carpenter: Report the build warning of extcon_{set|get}_cable_state_()]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
rndis_get_nr() returns either a non-negative value on success
or a negative value on failure. In case of failure an error code
is returned to the caller of rndis_register().
If the "i" is unsigned, the information about error from rndis_get_nr()
is lost. If there is no error but rndis_get_nr() returns a value greater
than 256 the least significant bits of i are zero effectively limiting the
number of configs to 256.
This patch fixes that.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If CONFIG_USB_GADGET_DEBUG_FILES is set then a block is opened and inside
it there is a local variable "i" which hides the "i" local to the
rndis_deregister(). Consequently, a random value is formatted
into the "name" buffer.
This patch removes the block-local i.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch:
83210e59ee
usb: gadget: rndis: use rndis_params instead of configNr
should change all invocations of rndis_signal_(dis)connect().
This patch fixes that.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds support for new Xsens device, Motion Tracker Development Board,
using Xsens' own Vendor ID
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are a few device-id changes removing a duplicate entry, refining
another and adding a third.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=kack
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.1-rc4
Here are a few device-id changes removing a duplicate entry, refining
another and adding a third.
Signed-off-by: Johan Hovold <johan@kernel.org>
INTSTS1 and INTENB1 register of renesas_usbhs can access only Host mode.
This adds process of accessing INTSTS1 and INTENB1 only when renesas_usbhs
is Host mode.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Registers DWC3's ULPI interface with the ULPI bus when it's
available.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some BYT platforms the USB2 PHY needs to be put into
operational mode by the controller driver with GPIOs
controlling the PHYs reset and cs signals.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This allows dwc3_phy_setup() to be more useful later. There
is nothing preventing the PHY configuration registers from
being programmed early. They do not loose their context in
soft reset.
There are however other PHY related operations that should
be executed before the driver request handles to the PHYs,
such as registering DWC3's ULPI interface, which can now be
done in dwc3_phy_setup().
Also, if there ever was need for the two 100ms delays in
dwc3_phy_setup() there isn't anymore. The PHYs are now reset
after the PHY interfaces are setup.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So it can be called from other places later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So they are available when ULPI interface support is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to store it before phys are handled, so we can later
use it in ULPI interface support code.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make selection between ULPI and UTMI+ interfaces possible by
providing definition for the bit in Global USB2 PHY
Configuration Register that controls it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Definitions for Global USB2 PHY Vendor Control Register
bits. We will need them to access ULPI PHY registers later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UTMI+ Low Pin Interface (ULPI) is a commonly used PHY
interface for USB 2.0. The ULPI specification describes a
standard set of registers which the vendors can extend for
their specific needs. ULPI PHYs provide often functions
such as charger detection and ADP sensing and probing.
There are two major issues that the bus type is meant to
tackle:
Firstly, ULPI registers are accessed from the controller.
The bus provides convenient method for the controller
drivers to share that access with the actual PHY drivers.
Secondly, there are already platforms that assume ULPI PHYs
are runtime detected, such as many Intel Baytrail based
platforms. They do not provide any kind of hardware
description for the ULPI PHYs like separate ACPI device
object that could be used to enumerate a device from.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit db62b9a804 (usb: dwc2: host: don't
use dma_alloc_coherent with irqs disabled)
introduced a build warning by using NULL
as an integer. Fix that by just using 0 instead
of NULL.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Getting phys by index instead of phy names so that we do
not have to create a naming scheme when multiple phys are present
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Getting phys by index instead of phy names so that we do
not have to create a naming scheme when multiple phys
are present
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
While accessing a unusual usb storage (ums-alauda, ums-cypress, ...),
the module reference count is not incremented. Because these drivers
allocate scsi hosts with usb_stor_host_template defined in usb-storage
module. So these drivers always can be unloaded.
This fixes it by preparing scsi host template which is initialized
at module_init() for each ums-* driver. In order to minimize the
difference in ums-* drivers, introduce module_usb_stor_driver() helper
macro which is same as module_usb_driver() except that it also
initializes scsi host template.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Vinayak Holikatti <vinholikatti@gmail.com>
Cc: Dolev Raviv <draviv@codeaurora.org>
Cc: Sujit Reddy Thumma <sthumma@codeaurora.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hannes Reinecke <hare@suse.de>
Cc: linux-usb@vger.kernel.org
Cc: usb-storage@lists.one-eyed-alien.net
Cc: linux-scsi@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
CC: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Petr Mladek <pmladek@suse.cz>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Antoine Tenart <antoine.tenart@free-electrons.com>
CC: Petr Mladek <pmladek@suse.cz>
CC: Michal Sojka <sojka@merica.cz>
CC: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Petr Mladek <pmladek@suse.cz>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Fixed two warnings sizeof name and Blank line after declaration
Signed-off-by: Nizam Haider <nizamhaider786@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy-rcar-gen2-usb driver, which supports legacy platform data only,
is no longer used since commit a483dcbfa2 ("ARM: shmobile: lager:
Remove legacy board support").
This driver was superseded by the DT-only phy-rcar-gen2 driver, which
was introduced in commit 1233f59f74 ("phy: Renesas R-Car Gen2 PHY
driver").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this flag some versions of these enclosures do not work.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christian Schaller <cschalle@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've had the same issue as described in commit
c68929f75d
Except my touchscreen's ID is
ID 04f3:0125 Elan Microelectronics Corp.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)
With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.
A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and and Split transaction errors for LS/FS
interrupt devices.
Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.
The default size used to be 64 TRBs per segment
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.
This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.
Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVSb+6AAoJEEhZKYFQ1nG7aRAH/AjHpptKlk06r1heeJxBcqhP
cDRmAXEPet1r/elds8HDkKiMVwHA2CrHKaAO569qfXdrW7mYO0b1u4rjTpN762ky
zHm+tYftI+5s0SXlSxrtVpexBsP+o26bk7g2VSdpR4VvN/iyuK1EAmP0t8C8uYtL
vzjN9oBZB9nLESaFTBCHGZ4oTRjKbch1BAYOgCpDhKx3YzU8aVh6WwHarL96hz/i
WGfBhLQqc7bT/VAB73odSgKYI2m2S5aWSjRbOruYM/GpjvO0shcAPJUTncMGE8d1
6/IbnPmYnGpIQMSxKPstk7Od2mCdF0IS5BzR1lElHihtzkLJ49bmWQNBmcMZ6Pg=
=/AOj
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Only a small fix for /sys entry
Here's the first pull request for v4.1-rc cycle,
it contains a few interesting fixes including a
fix to correct register offsets on dwc3, a fix
for Kconfig dependencies on isp1301 phy driver,
and a bug fix for our configfs gadget creation
interface.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X26W
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.1-rc2
Here's the first pull request for v4.1-rc cycle,
it contains a few interesting fixes including a
fix to correct register offsets on dwc3, a fix
for Kconfig dependencies on isp1301 phy driver,
and a bug fix for our configfs gadget creation
interface.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.01+ full-speed devices can have extended descriptor as well
and can support LPM.
Signed-off-by: Rupesh Tatiya <rtatiya@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Single transform macros with hidden arguments are not
particularly useful. Just use seq_printf directly instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB PCI quirks code gets built into the kernel whenever CONFIG_PCI
is enabled, even if CONFIG_USB is not set. This can cause unnecessary
messages to show up in the kernel log, such as "CONFIG_USB_XHCI_HCD is
turned off, defaulting to EHCI" (which makes no sense when the kernel
has been configured without host-side USB support).
This patch addresses the problem by building pci-quirks.o only when
CONFIG_PCI and CONFIG_USB are both enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Microsoft document "Using ACPI to Configure USB Ports on a Computer"
makes it clear that the removable flag will be cleared on ports that are
marked as unused by the firmware. Handle this case to match.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Windows appears to pay more attention to the ACPI values than any hub
configuration, so prefer the firmware's opinion on whether a port is
fixed or removable before falling back to the hub values.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a debugfs interface - softconnect - for host mode to
connect/disconnect the devices without physically remove the
them.
This adds the capability to re-enumerate the devices which are
permanently mounted on the board with the MUSB controller
together.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.
This patch allocates struct rndis_params on demand in rndis_register().
Coversly, the structure is free()'d in rndis_deregister().
If CONFIG_USB_GADGET_DEBUG_FILES is set, the proc files are created which
is the same behaviour as before, but the moment of creation is delayed
until struct rndis_params is actually allocated.
rnids_init() and rndis_exit() have nothing to do, so they are eliminated.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use a space between function name and parameter list opening bracket.
All other functions in this file comply wich checkpatch rules.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.
This patch prepares the elimination of the said limit by converting all the
functions which accept rndis config number to accept a pointer to the
actual struct rndis_params. Consequently, rndis_register() returns
a pointer to a corresponding struct rndis_params instance. The pointer
is then always used by f_rndis.c instead of config number when it talks
to rndis.c API.
A nice side-effect of the changes is that many lines of code in rndis.c
become shorter and fit in 80 columns.
If a function prototype changes in rndis.h a style cleanup is made
at the same time, otherwise checkpatch complains that the patch
has style problems.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using unnecessary static char buffers isn't good.
Use the %pV extension instead.
Miscellanea:
o the dprintk return value is unused, make it void
o add __printf format and argument verification
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can remove the ifdefs by setting up helper functions for
mentor DMA and cppi/tusb DMA.
Note that I've kept the existing formatting as otherwise this
patch becomes pretty much unreadable.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Let's get rid of the horrible ifdef in middle of the expression.
We can do it by adding a variable for short_packet and testing
it separately for DMA related code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For musb_core.c we can now just drop the DMA related
ifdef and use the already existing runtime test for
!is_cppi_enabled(musb) instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set up function pointers for DMA so get closer to
being able to build in all the DMA engines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pass struct musb to tusb_dma_omap() and is_cppi_enabled(),
and add macros for the other DMA controllers. Populate the
platform specific quirks with the DMA type and use it during
runtime.
Note that platform glue layers with no custom DMA code are
tagged with MUSB_DMA_INVENTRA which may have a chance of
working. Looks like the defconfigs for these use PIO_ONLY,
so this should not break existing configs.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A string written by the user may not be zero terminated.
sscanf may read memory beyond the buffer if no zero byte
is found.
For testing build with CONFIG_USB_CHIPIDEA=y, CONFIG_USB_CHIPIDEA_DEBUG=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
dwc2_hc_nak_intr could be called with a NULL qtd.
Ensure qtd exists before dereferencing it to avoid kernel panic.
This happens when using usb to ethernet adapter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2 may not be able to exit from hibernation if the hardware
does not provide a way to detect resume signalling in this state.
Thus, add the possibility to disable hibernation feature.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As dwc2 pci module is now exporting dwc2 platform device, include
platform.o in dwc2-y and remove USB_DWC2_PLATFORM configuration
option. Driver will be built as two modules, dwc2.ko and dwc2_pci.ko.
dwc2.ko is the new platform driver.
Remove all EXPORT_SYMBOL_GPL as they are not needed any more.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for SetPortFeature(PORT_TEST) for root port.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Jingwu Lin <jingwu.lin@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Align buffer must be allocated using kmalloc since irqs are disabled.
Coherency is handled through dma_map_single which can be used with irqs
disabled.
Reviewed-by: Julius Werner <jwerner@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During urb_enqueue, if the urb can't be queued to the endpoint,
the urb is freed without any spinlock protection.
This leads to memory corruption when concurrent urb_dequeue try to free
same urb->hcpriv.
Thus, ensure the whole urb_enqueue in spinlocked.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Once hub is runtime suspended, dwc2 must resume it
on port connect event.
Else, roothub will stay in suspended state and will
not resume transfers.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update controller state to indicate suspend entry.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If phy driver is present register hcd handle to it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Force argument is not used anymore. Clean up leftovers from
https://lkml.org/lkml/2014/12/9/283
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Inform that device is otg-capable in case of otg configuration.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During vbus session, usb controller needs to exit hibernation if it was
previously in suspend state.
Since controller will be resetted and configured, there is no need
to restore registers.
Moreover, set lx_state to L0 on B session. vbus_session callback may
not be used by all platforms. Thus, controller software state needs
to be set to L0 if the controller detects a valid B session.
Otherwise, lx_state will remain L2 and prevent any request submission.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb controller is in partial power down, any write to registers may
cause unpredictable behavior.
Thus, prevent any new request submission once controller is in partial
power down.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Nothing to be done in pm suspend/resume when controller is in L2.
Don't disconnect or reset. State is already saved when putting
controller in hibernation and will be restored on USB bus resume.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ResetDet interrupt is used to detect a reset of the bus
while the controller is suspended.
This may happens for example when using Command Verifier.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So the parameters can be used in both host and gadget modes.
Also consolidate param functions in the core.h
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is required due to an Intel specific hardware issue. Where id-
pin setup causes glitches on the interrupt line when CONIDSTSCHG
interrupt is enabled.
Specify external_id_pin_ctl when an external driver (for example phy)
can handle id change, so that CONIDSTSCHG interrupt can be disabled
from the controller.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During suspend, there could a race condition between ep_queue and
suspend interrupt if lx_state is updated after releasing spinlock in
call_gadget(hsotg, suspend).
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow controller to enter in hibernation during usb bus suspend and
inform both phy and gadget about the suspended state.
While in hibernation, the controller can't detect the resume condition.
An external mechanism must call usb_phy_set_suspend on resume.
Exit hibernation when controller gets the resume interrupt and inform
only gadget driver about it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When suspending usb bus, phy driver may disable controller power.
In this case, registers need to be saved on suspend and restored
on resume.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Dump all registers to take a complete snapshot of dwc2 state.
Code is inspired by dwc3/debugfs.c
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prepare to add more debug code. Moreover, don't save dentry * for
each file in struct dwc2_hsotg as clean up is done with
debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed
altogether for the same reason.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Samsung has just released a portable USB3 SSD, coming in a very small
and nice form factor. It's USB ID is 04e8:8001, which unfortunately is
already used by the Palm Visor driver for the Samsung I330 phone cradle.
Having pl2303 or visor pick up this device ID results in conflicts with
the usb-storage driver, which handles the newly released portable USB3
SSD.
To work around this conflict, I've dug up a mailing list post [1] from a
long time ago, in which a user posts the full USB descriptor
information. The most specific value in this appears to be the interface
class, which has value 255 (0xff). Since usb-storage requires an
interface class of 0x8, I believe it's correct to disambiguate the two
devices by matching on 0xff inside visor.
[1] http://permalink.gmane.org/gmane.linux.usb.user/4264
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This phone is already supported by the visor driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the USB serial console device ID for KCF Technologies PRN device
which has a USB port for its serial console.
Signed-off-by: Mark Edwards <sonofaforester@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The phy-rcar-gen2-usb driver, which supports legacy platform data only,
is no longer used since commit a483dcbfa2 ("ARM: shmobile: lager:
Remove legacy board support").
This driver was superseded by the DT-only phy-rcar-gen2 driver, which
was introduced in commit 1233f59f74 ("phy: Renesas R-Car Gen2 PHY
driver").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
VBUS is not routed to USB PHY on recent Qualcomm platforms. USB controller
must see VBUS in order to pull-up DP when setting RS bit. Henc configure
USB PHY and LINK registers sense VBUS and enable manual pullup on D+ line.
Cc: Vamsi Krishna <vskrishn@codeaurora.org>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Phil and I found out a problem with commit:
7e860a6e7a ("cdc-acm: add sanity checks")
It added some sanity checks to ignore potential garbage in CDC headers but
also introduced a potential infinite loop. This can happen at the first
loop iteration (elength = 0 in that case) if the description isn't a
DT_CS_INTERFACE or later if 'buffer[0]' is zero.
It should also be noted that the wrong length was being added to 'buffer'
in case 'buffer[1]' was not a DT_CS_INTERFACE descriptor, since elength was
assigned after that check in the loop.
A specially crafted USB device could be used to trigger this infinite loop.
Fixes: 7e860a6e7a ("cdc-acm: add sanity checks")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
CC: Oliver Neukum <oneukum@suse.de>
CC: Adam Lee <adam8157@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 70843f623b ("usb: host: ehci-msm: Use
devm_ioremap_resource instead of devm_ioremap") and commit
e507bf577e ("host: ehci-msm: remove duplicate check on resource"),
because msm_otg and this driver are using same address space to
access AHB mode and USB command registers.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrongly release mutex lock during otg_statemachine may result in re-enter
otg_statemachine, which is not allowed, we should do next state transtition
after previous one completed.
Fixes: 826cfe751f ("usb: chipidea: add OTG fsm operation functions implementation")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing has shown that ASM1053 devices do not work properly with transfers
larger than 240 sectors, so set max_sectors to 240 on these.
Cc: stable@vger.kernel.org # 3.16
Reported-by: Steve Bangert <sbangert@frontier.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Steve Bangert <sbangert@frontier.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb-storage driver sets max_sectors = 240 in its scsi-host template,
for uas we do not want to do that for all devices, but testing has shown
that some devices need it.
This commit adds a US_FL_MAX_SECTORS_240 flag for such devices, and
implements support for it in uas.c, while at it it also adds support
for US_FL_MAX_SECTORS_64 to uas.c.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uas_use_uas_driver may set some US_FL_foo flags during detection, currently
these are stored in a local variable and then throw away, but these may be
of interest to the caller, so add an extra parameter to (optionally) return
the detected flags, and use this in the uas driver.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUSB test mode register can only be set once, otherwise the result
is undefined.
This prevents the debugfs testmode entry to set the register more than
once which causes test failure.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current usbhs_for_each_dfifo macro will read out-of-array's
memory after last loop operation.
It was not good C language operation, and the binary which was
compiled by (at least) gcc 4.8.1 is broken.
This patch is based on
925403f425
(usb: renesas_usbhs: tidyup original usbhsx_for_each_xxx macro)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isp1301-omap driver contains special hooks for the TPS65010
power management controller. It provides its own 'tps65010_set_vbus_draw'
wrapper in case that driver is not enabled through Kconfig, but
fails to handle the case where isp1301-omap is built-in but TPS65010
is a loadable module, which currently results in a link error:
drivers/built-in.o: In function `isp1301_set_power':
:(.text+0x14e188): undefined reference to `tps65010_set_vbus_draw'
This is a workaround to use the same trick as before also when
tps65010 is a module. Doing a proper fix would require much larger
changes to the driver that is not really worth it when the usb-phy
drivers are going to eventually get replaced with generic-phy
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a single thread is sending out data over the gadget serial port,
gs_start_tx() will be called both from the sender context and from the
write completion. Since the port lock is released before the packet is
queued, the order in which the URBs are submitted is not guaranteed.
E.g.
sending thread completion (interrupt)
gs_write()
LOCK
gs_write_complete()
LOCK (wait)
gs_start_tx()
req1 = list_entry(pool->next)
UNLOCK
LOCK (acquired)
gs_start_tx()
req2 = list_entry(pool->next)
UNLOCK
usb_ep_queue(req2)
usb_ep_queue(req1)
I.e., req2 is submitted before req1 but it contains the data that
comes after req1.
To reproduce, use SMP with sending thread and completion pinned to
different CPUs, or use PREEMPT_RT, and add the following delay just
before the call to usb_ep_queue():
if (port->write_started > 0 && !list_empty(pool))
udelay(1000);
To work around this problem, make sure that only one thread is running
through the gs_start_tx() loop with an extra flag write_busy. Since
gs_start_tx() is always called with the port lock held, no further
synchronisation is needed. The original caller will continue through
the loop when the request was successfully submitted.
Signed-off-by: Philip Oberstaller <Philip.Oberstaller@septentrio.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we have multiple instances of hid function, each of
them may have different report descriptor, also their
length may be different.
Currently we are using static hidg_desc varable which
is being filled in hidg_bind(). Then we send its content
to host in hidg_setup() function. This content may
have been already overwriten if another instance
has executed hidg_bind().
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource() returns IOMEM_ERR_PTR() and it never
returns NULL, fix the check to prevent access to invalid
virtual address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The macros related to register UTMI_OTG_CTRL and UTMI_OTG_STATUS are
swapped. Correct them for readability.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
Pull second vfs update from Al Viro:
"Now that net-next went in... Here's the next big chunk - killing
->aio_read() and ->aio_write().
There'll be one more pile today (direct_IO changes and
generic_write_checks() cleanups/fixes), but I'd prefer to keep that
one separate"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
->aio_read and ->aio_write removed
pcm: another weird API abuse
infinibad: weird APIs switched to ->write_iter()
kill do_sync_read/do_sync_write
fuse: use iov_iter_get_pages() for non-splice path
fuse: switch to ->read_iter/->write_iter
switch drivers/char/mem.c to ->read_iter/->write_iter
make new_sync_{read,write}() static
coredump: accept any write method
switch /dev/loop to vfs_iter_write()
serial2002: switch to __vfs_read/__vfs_write
ashmem: use __vfs_read()
export __vfs_read()
autofs: switch to __vfs_write()
new helper: __vfs_write()
switch hugetlbfs to ->read_iter()
coda: switch to ->read_iter/->write_iter
ncpfs: switch to ->read_iter/->write_iter
net/9p: remove (now-)unused helpers
p9_client_attach(): set fid->uid correctly
...
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that
user space tools like perf and trace-cmd can parse the binary data
and express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values
by the C pre-processor. Thus, the enum string is exported to the
format file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings
in the TP_printk() format into their number, and that is what is
shown to user space. For example, the tracepoint tlb_flush currently
has this in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVLBTuAAoJEEjnJuOKh9ldjHMIALdRS755TXCZGOf0r7O2akOR
wMPeum7C+ae1mH+jCsJKUC0/jUfQKaMt/UxoHlipDgcGg8kD2jtGnGCw4Xlwvdsr
y4rFmcTRSl1mo0zDSsg6ujoupHlVYN0+JPjrd7S3cv/llJoY49zcanNLF7S2XLeM
dZCtWRLWYpBiWO68ai6AqJTnE/eGFIqBI048qb5Eg8dbK243SSeSIf9Ywhb+VsA+
aq6F7cWI/H6j4tbeza8tAN19dcwenDro5EfCDY8ARQHJu1f6Y3+DLf2imjkd6Aiu
JVAoGIjHIpI+djwCZC1u4gi4urjfOqYartrM3Q54tb3YWYqHeNqP2ASI2a4EpYk=
=Ixwt
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Some clean ups and small fixes, but the biggest change is the addition
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that user
space tools like perf and trace-cmd can parse the binary data and
express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values by
the C pre-processor. Thus, the enum string is exported to the format
file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings in
the TP_printk() format into their number, and that is what is shown to
user space. For example, the tracepoint tlb_flush currently has this
in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })"
* tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (27 commits)
tracing: Add enum_map file to show enums that have been mapped
writeback: Export enums used by tracepoint to user space
v4l: Export enums used by tracepoints to user space
SUNRPC: Export enums in tracepoints to user space
mm: tracing: Export enums in tracepoints to user space
irq/tracing: Export enums in tracepoints to user space
f2fs: Export the enums in the tracepoints to userspace
net/9p/tracing: Export enums in tracepoints to userspace
x86/tlb/trace: Export enums in used by tlb_flush tracepoint
tracing/samples: Update the trace-event-sample.h with TRACE_DEFINE_ENUM()
tracing: Allow for modules to convert their enums to values
tracing: Add TRACE_DEFINE_ENUM() macro to map enums to their values
tracing: Update trace-event-sample with TRACE_SYSTEM_VAR documentation
tracing: Give system name a pointer
brcmsmac: Move each system tracepoints to their own header
iwlwifi: Move each system tracepoints to their own header
mac80211: Move message tracepoints to their own header
tracing: Add TRACE_SYSTEM_VAR to xhci-hcd
tracing: Add TRACE_SYSTEM_VAR to kvm-s390
tracing: Add TRACE_SYSTEM_VAR to intel-sst
...
Here's the big USB (and PHY) driver patchset for 4.1-rc1.
Everything here has been in linux-next, and the full details are below
in the shortlog. Nothing major, just the normal round of new
drivers,api updates, and other changes, mostly in the USB gadget area,
as usual.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUsHXYACgkQMUfUDdst+ykGvwCfbI3z0VYJqyvPi7pbn+jtGouQ
E7MAoICdP90ofZfyzQzXy+2xKTTCiP5L
=jSjh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver updates from Greg KH:
"Here's the big USB (and PHY) driver patchset for 4.1-rc1.
Everything here has been in linux-next, and the full details are below
in the shortlog. Nothing major, just the normal round of new
drivers,api updates, and other changes, mostly in the USB gadget area,
as usual"
* tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (252 commits)
drivers/usb/core: devio.c: Removed an uneeded space before tab
usb: dwc2: host: sleep USB_RESUME_TIMEOUT during resume
usb: chipidea: debug: add low power mode check before print registers
usb: chipidea: udc: bypass pullup DP when gadget connect in OTG fsm mode
usb: core: hub: use new USB_RESUME_TIMEOUT
usb: isp1760: hcd: use new USB_RESUME_TIMEOUT
usb: dwc2: hcd: use new USB_RESUME_TIMEOUT
usb: host: sl811: use new USB_RESUME_TIMEOUT
usb: host: r8a66597: use new USB_RESUME_TIMEOUT
usb: host: oxu210hp: use new USB_RESUME_TIMEOUT
usb: host: fusbh200: use new USB_RESUME_TIMEOUT
usb: host: fotg210: use new USB_RESUME_TIMEOUT
usb: host: isp116x: use new USB_RESUME_TIMEOUT
usb: musb: use new USB_RESUME_TIMEOUT
usb: host: uhci: use new USB_RESUME_TIMEOUT
usb: host: ehci: use new USB_RESUME_TIMEOUT
usb: host: xhci: use new USB_RESUME_TIMEOUT
usb: define a generic USB_RESUME_TIMEOUT macro
usb: musb: dsps: fix build on i386 when COMPILE_TEST is set
ehci-hub: use USB_DT_HUB
...
All places outside of core VFS that checked ->read and ->write for being NULL or
called the methods directly are gone now, so NULL {read,write} with non-NULL
{read,write}_iter will do the right thing in all cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Ran checkpatch.pl on file and removed a warning about an unwanted space before
a tab.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msleep(USB_RESUME_TIMEOUT) must be done when the controller drives
the resume. This is true after HPRT0_RES is written.
Moreover, restore the delay after controller power is up.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Forbid dumpping registers when the controller in low power mode
- dp pullup needs to be controlled by fsm when working at otg
fsm mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVJM1NAAoJEEhZKYFQ1nG7s80IALrPTj0ZqVmH5FjWQt49I7Bj
Q2UAFDvINhSufJynlcHbVB0G6XbEtn/T+5Qnx8WJhDqnODgI9CGk+WsFPmJilrj6
DCvTaUsCNK3ERK1yBGqUIE+gV/ku2NYO+BnKA2Leh2Vb+/KENTs2v+Lr1sRd5qMO
u7kmyZlID997A4h2RDW23oJgynPlTTgwg26VXGshCmeqH4UnoLQ1Gfm3+iQ1ItsM
9Ka6HKJTqP9tBYh/mgI4G7If6EI+L4EVH1Hyfy8uConwcbkyaKRA8cR1o0at/A4s
Npoma8NVw7PMit1cMwzEUECbfY3fjVQLI4j1PTDsWdRvDKxqCHre64erq/NH+g4=
=zOdE
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Two Chipidea updates
- Forbid dumpping registers when the controller in low power mode
- dp pullup needs to be controlled by fsm when working at otg
fsm mode
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVJEivAAoJEIaOsuA1yqREV6QP/1oJVdBxzOeQVXyGZsZT4k0E
T8SKmTIJmaCdSjgazSXAhqF7IR992sTM7urHZ2hww3tftODNVHvfFkgDlSguHwkr
GV95YpNv99ash7spjod3xVOt8lDvrt6FHs7Foj4b0yQZ1yXUZsOH4j8G4gMYOgTd
bq1mO2/NaaM7xiddzPMCGpSkL6NcsWrurJ8JiOlBXaUIkSR+Cwe9+8vzEDrxfSM+
6yBTLQCdvR0ammqV0YMNsF9dGLO8yiDotC6b104i3yCqpAZnyj0RJQ3riH7ESxsG
eSKkCXXGY0OWDGDcnWTskYEHJ7iDfg5MrlzBJyneMjauGKNeIoJRRYWP/f6NSV9m
GHxRV1ITKC61Dtt3w+Oy2a16UpAbq7/w1q/SkQl4YtJ8l0P1PUb+TfOZpTOsCLLF
cLXUKJufGWhuGbo+e2m6GizNCsDi5LlfdZcjIjVKRXpyiZI0peqyGj16mTm70UUY
/A9nsLtE7c6bqHMTcFQFRx4d2iHmkilyzQqOvx4ulo1rovNMafgmZJF7Kq0LY7ZO
Uj4s2rEAjqbELbOiEIf8HzGP+J/QuECG4SHyPEQsiG0drYyoCOqGR1S3kV7aJgFz
krl4zTvXR8EOk2IpPa8PDzmMr7YCYzlXOxzmSoJiZhqqpLH7cHYkDiRTmyxn+eB3
lEjEzBA8J9CG4iRIFjk3
=RqsO
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
trivial conflict in net/socket.c and non-trivial one in crypto -
that one had evaded aio_complete() removal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since the required clock to access registers is gated off in low power mode,
add ci->in_lpm check before try to dump registers value.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
By pass pullup DP in OTG fsm mode when do gadget connect, to let it handled
by OTG state machine.
This patch can fix the problem you found with my HNP polling patchset after
below 3 patches introduced:
467a78c usb: chipidea: udc: apply new usb_udc_vbus_handler interface
628ef0d usb: udc: add usb_udc_vbus_handler
dfea9c9 usb: udc: store usb_udc pointer in struct usb_gadget
Problem:
- Connect USB cable and MicroAB cable between two boards
- Boot up two boards
- load g_mass_storage at B-device side, the enumeration will success,
and A will see a usb mass-storage device
- load g_mass_storage at A-device side, the problem has occurred, the
connection will be lost at the beginning, then connect again.
This patch is based on
commit eff933c1d3a2e046492b3dfc86db813856553a29
(chipidea: pci: make it depends on NOP_USB_XCEIV)
on branch peter-usb-dev of
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
While this driver was already using a 50ms resume
timeout, let's make sure everybody uses the same
macro so it's easy to fix later should anything
go wrong.
It also gives a more "stable" expectation to Linux
users.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Based on original work by Bin Liu <Bin Liu <b-liu@ti.com>>
Cc: Bin Liu <b-liu@ti.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
New code will require TRACE_SYSTEM to be a valid C variable name,
but some tracepoints have TRACE_SYSTEM with '-' and not '_', so
it can not be used. Instead, add a TRACE_SYSTEM_VAR that can
give the tracing infrastructure a unique name for the trace system.
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
fixed a USB error on dm816x, but introduced a new build error on i386
when COMPILE_TEST is set:
drivers/usb/musb/musb_dsps.c: In function ‘dsps_read_fifo32’:
drivers/usb/musb/musb_dsps.c:624:3: error: implicit declaration of function
‘readsl’ [-Werror=implicit-function-declaration]
readsl(fifo, dst, len >> 2);
Let's fix this by using ioread32_rep() instead of readsl() as that's
more portable.
Fixes: 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'bHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'bDescriptorType' field of the Hub
Descriptors while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when HW_RANDOM is not enabled:
drivers/built-in.o: In function `chaoskey_disconnect':
chaoskey.c:(.text+0x5f3f00): undefined reference to `hwrng_unregister'
drivers/built-in.o: In function `chaoskey_probe':
chaoskey.c:(.text+0x5f42a6): undefined reference to `hwrng_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the technical update (No. TN-RCS-B011A/E), the UGSTS LOCK
bit location is bit 8, not bits 9 and 8. So, this patch fixes the
USBHS_UGSTS_LOCK value.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up the f81232 driver, which up to this point has mostly been a
placeholder without a proper implementation.
Included is also a minor clean up of ch341.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OFj7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.1-rc1
Fix up the f81232 driver, which up to this point has mostly been a
placeholder without a proper implementation.
Included is also a minor clean up of ch341.
Signed-off-by: Johan Hovold <johan@kernel.org>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
> drivers/usb/misc/chaoskey.c: In function 'chaoskey_read':
> >> drivers/usb/misc/chaoskey.c:412:3: error: implicit declaration of function 'copy_to_user'
> >> [-Werror=implicit-function-declaration]
> remain = copy_to_user(buffer, dev->buf + dev->used, this_time);
I was unable to reproduce this locally, but added an explicit
#include <linux/uaccess.h>
which should ensure the definition on all architectures.
> sparse warnings: (new ones prefixed by >>)
>
> >> drivers/usb/misc/chaoskey.c:117:30: sparse: incorrect type in assignment (different base types)
> drivers/usb/misc/chaoskey.c:117:30: expected int [signed] size
> drivers/usb/misc/chaoskey.c:117:30: got restricted __le16 [usertype] wMaxPacketSize
Switched the code to using the USB descriptor accessor functions.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few new device IDs.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8dFl
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.0-rc6
Here are a few new device IDs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add me to co-author and fix no '>' in greg kh's email
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
We remove non-used define in this patch to avoid wrong usage.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
We extract TIOCGSERIAL section in f81232_ioctl() to f81232_get_serial_info()
to make it clarify.
Also we fix device type from 16654 to 16550A, and set it's baud_base
to 115200 (1.8432MHz/16).
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The original driver had do not any h/w change in driver.
This patch implements with configure H/W for
baud/parity/word length/stop bits functional in f81232_set_termios().
This patch also implement DTR/RTS control when baudrate B0.
We drop DTR/RTS when B0, otherwise enable it.
We are checking baudrate in set_termios() too, If baudrate larger then 115200,
it will be changed to 115200 and use tty_encode_baud_rate() to encode into tty
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
We put FCR/IER initial step to f81232_port_enable()/f81232_port_disable().
When port is open, it set MSR interrupt on. Otherwise set it off.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Johan Hovold