CodingStyle does not allow C99 style comments. Since the
dts files live in the kernel for now, make this compliant.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>
Add SDHCI bindings for the Broadcom 281xx SoCs.
Changes from V2:
- Documentation cleanups
Changes from V1:
- split original patch into 2, one for driver and this one for dt
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHg+
-----END PGP SIGNATURE-----
Merge tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
cleanup and removing dead code for only support DT for exynos
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
* tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (35 commits)
ARM: EXYNOS: Remove remaining dead code after non-DT support removal
ARM: EXYNOS: Remove legacy L2X0 initialization
ARM: EXYNOS: Use exynos_init_io() as map_io callback
ARM: EXYNOS: Remove custom init_irq callbacks
ARM: EXYNOS: Remove mach/regs-usb-phy.h header
thermal: exynos: Support both EXYNOS4X12 SoCs
ARM: EXYNOS: Remove unused base addresses from mach/map.h header
ARM: EXYNOS: Remove mach/irqs.h header
ARM: EXYNOS: Select SPARSE_IRQ for Exynos
ARM: SAMSUNG: Make legacy MFC support code depend on SAMSUNG_ATAGS
ARM: EXYNOS: Remove mach/regs-gpio.h header
ARM: EXYNOS: Remove mach/gpio.h
ARM: EXYNOS: Remove setup-i2c0.c
ARM: EXYNOS: Do not select legacy Kconfig symbols any more
ARM: SAMSUNG: Include most of mach/ headers conditionally
ARM: EXYNOS: Decouple ARCH_EXYNOS from PLAT_S5P
USB: Check for ARCH_EXYNOS separately
platform: Check for ARCH_EXYNOS separately
ARM: SAMSUNG: Compile legacy IRQ and GPIO PM code only with ATAGS support
ARM: EXYNOS: Provide compatibility stubs for PM code in pm-core.h header
...
Conflicts:
arch/arm/mach-exynos/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- use #include for all Samsung DT
- add clk for exynos audio subsystem (audss) and i2s
- support audss and i2s for exynos5250
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0n6B
-----END PGP SIGNATURE-----
Merge tag 'common-clk-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
From Kukjin Kim:
based on exynos-dt-2 and s3c24xx-dt-2
- use #include for all Samsung DT
- add clk for exynos audio subsystem (audss) and i2s
- support audss and i2s for exynos5250
* tag 'common-clk-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- update uart addresses in s3c2416-dt auxdata due to removing S3C2410_PA_UARTX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Cuff
-----END PGP SIGNATURE-----
Merge tag 's3c24xx-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
based on tags/s3c24xx-dt-1
- update uart addresses in s3c2416-dt auxdata due to removing S3C2410_PA_UARTX
* tag 's3c24xx-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: update uart addresses in s3c2416-dt auxdata
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- enable RTC on exynos5250 snow and Arndale boards
- add support LCD and PWM for exynos4210 Origen board
- update bootargs to support 8GiB for exynos5440 SSDK5440 and SD5v1 boards
- enable spi and add opp level for exynos5440
- add example doc for samsung-pinctrl dt bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sN6E
-----END PGP SIGNATURE-----
Merge tag 'exynos-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
2nd exynos dt update based on tags/exynos-dt-1
- enable RTC on exynos5250 snow and Arndale boards
- add support LCD and PWM for exynos4210 Origen board
- update bootargs to support 8GiB for exynos5440 SSDK5440 and SD5v1 boards
- enable spi and add opp level for exynos5440
- add example doc for samsung-pinctrl dt bindings
* tag 'exynos-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Set BUCK7 as always on for Origen board
ARM: dts: Add FIMD node to Origen4210 board
ARM: dts: Add LCD related pinctrl entries for exynos4210
ARM: dts: Add PWM related pinctrl entries for exynos4210
Documentation: Add examples to samsung-pinctrl device tree bindings documentation
ARM: dts: Enable RTC node for exynos5250-snow
ARM: dts: Enable RTC node for Arndale
ARM: dts: Removing pdma for exynos5440
ARM: dts: update bootargs to support 8GiB for SSDK5440 and SD5v1
ARM: dts: Add more opp levels in exynos5440
ARM: dts: Add wm8994 regulator support on smdk5250
ARM: dts: enable spi for EXYNOS5440 SOC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- enable XHCI on exynos5
- enable Pinctrl on exynos4 and exynos5
- calling scu_enable() is only available on Cortex-A9
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oexl
-----END PGP SIGNATURE-----
Merge tag 'exynos-arch-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
arch/arm/mach-exynos update
- enable XHCI on exynos5
- enable Pinctrl on exynos4 and exynos5
- calling scu_enable() is only available on Cortex-A9
* tag 'exynos-arch-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: call scu_enable() only in case of cortex-A9 processor
ARM: EXYNOS: Select PINCTRL_EXYNOS for exynos4/5 at chip level
ARM: EXYNOS: Enable XHCI support on exynos5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The OMAP Mailbox driver framework is moved out of arch/arm folder
into drivers/mailbox folder, to re-enable building it and also serve
as a baseline for adapting to the new mailbox driver framework. The
changes mainly contain:
- a minor bug fix and cleanup of mach-specific mailbox code
- remove any header dependencies from plat-omap for multi-platform
support
- represent mailbox device data through platform data/hwmod attrs
- move the omap mailbox code out of plat-omap/mach-omapX to
drivers/mailbox folder
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=j0vK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/mailbox-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
From Tony Lindgren:
Move OMAP Mailbox framework to drivers via Suman Anna <s-anna@ti.com>
The OMAP Mailbox driver framework is moved out of arch/arm folder
into drivers/mailbox folder, to re-enable building it and also serve
as a baseline for adapting to the new mailbox driver framework. The
changes mainly contain:
- a minor bug fix and cleanup of mach-specific mailbox code
- remove any header dependencies from plat-omap for multi-platform
support
- represent mailbox device data through platform data/hwmod attrs
- move the omap mailbox code out of plat-omap/mach-omapX to
drivers/mailbox folder
* tag 'omap-for-v3.11/mailbox-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mailbox/omap: move the OMAP mailbox framework to drivers
ARM: OMAP2+: add user and fifo info to mailbox platform data
ARM: OMAP2+: mbox: remove dependencies with soc.h
omap: mailbox: correct the argument type for irq ops
omap: mailbox: call request_irq after mbox queues are allocated
omap: mailbox: check iomem resource before dereferencing it
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
omap-for-v3.11/gpmc-signed branch because of a compile error
it caused. The compile error is fixed in this version.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IxbH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/gpmc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
From Tony Lindgren:
GPMC suspend patch that was left out of the earlier
omap-for-v3.11/gpmc-signed branch because of a compile error
it caused. The compile error is fixed in this version.
* tag 'omap-for-v3.11/gpmc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: gpmc: Low power transition support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
tapering down finally as we're getting closer to making
omap2+ DT only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5gWz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren:
Minor board changes for v3.11 merge window. These are
tapering down finally as we're getting closer to making
omap2+ DT only.
* tag 'omap-for-v3.11/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
ARM: OMAP1: nokia770: enable Tahvo
ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
arm: omap: board-overo: reset GPIO for SMSC911x
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A recent cleanup caused build errors in some configurations
because the header defining NR_IRQS_LEGACY is not included
here. Since that value is the default, we can just as well
leave it out.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Commit 5336539 "ARM: S5P64X0: Use common uncompress.h part
for plat-samsung" was missing a type cast, this brings
it in line with the other samsung platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Cleanup watchdog support on Samsung to support multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zkPJ
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
- Consolidate uncompress subroutines and s5p64x0-uncompress
- Cleanup watchdog support on Samsung to support multiplatform
* tag 'samsung-cleanup-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Remove unused plat/regs-watchdog.h header
ARM: SAMSUNG: Remove legacy watchdog reset code
ARM: SAMSUNG: Let platforms use the new watchdog reset driver
ARM: SAMSUNG: Add watchdog reset driver
ARM: SAMSUNG: Use local definitions of watchdog registers
watchdog: s3c2410_wdt: Use local register definitions
ARM: S5P64X0: Use common uncompress.h part for plat-samsung
ARM: SAMSUNG: Consolidate uncompress subroutine
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OMAP: PM: remove requirement for voltage domain data; remove dummy data
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=KjMH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/pm-voltdomain-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
PM voltage domain clean-up via Kevin Hilman <khilman@linaro.org>:
OMAP: PM: remove requirement for voltage domain data; remove dummy data
* tag 'omap-for-v3.11/pm-voltdomain-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: AM33xx: Remove the unused voltagedomain data
ARM: OMAP2+: Powerdomain: Remove the need to always have a voltdm associated to a pwrdm
Includes an update to Linux 3.10-rc6.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OMAP: PM: the serial core + driver can no handle no_console_suspend support
without any SoC specific handlding or SoC-specific DT bindings. Remove
the now unused SoC specifics for OMAP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yja+
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/pm-serial-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Serial driver platform init code clean-up via Kevin Hilman <khilman@linaro.org>:
OMAP: PM: the serial core + driver can no handle no_console_suspend support
without any SoC specific handlding or SoC-specific DT bindings. Remove
the now unused SoC specifics for OMAP.
* tag 'omap-for-v3.11/pm-serial-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: omap2+: omap_device: remove no_idle_on_suspend
arm: dts: am33xx: Remove "ti,no_idle_on_suspend" property.
arm: omap2+: serial: remove no_console_suspend support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
patch from the already merged omap-for-v3.11/soc-signed branch.
Also fixes for ti81x booting and revision check updates.
These are based on omap-for-v3.11/soc-signed because of the
am43x dependency to earlier patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=4brz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/soc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Fix am43x minimal booting as I accidentally left out one
patch from the already merged omap-for-v3.11/soc-signed branch.
Also fixes for ti81x booting and revision check updates.
These are based on omap-for-v3.11/soc-signed because of the
am43x dependency to earlier patches.
* tag 'omap-for-v3.11/soc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: am33xx id: Add new am33xx specific function to check dev_feature
ARM: OMAP: TI816X: add powerdomains for TI816x
ARM: OMAP2: TI81XX: id: Add cpu id for TI816x ES2.0 and ES2.1
ARM: OMAP2+: AM43x: basic dt support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Lee Jones' pinctrl compat ontology patches
- A real clock driver for the Nomadik, 100% DT-based
- Device tree changes for the Nomadik clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=0yyI
-----END PGP SIGNATURE-----
Merge tag 'nomadik-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Nomadik DT and clock work:
- Lee Jones' pinctrl compat ontology patches
- A real clock driver for the Nomadik, 100% DT-based
- Device tree changes for the Nomadik clocks
* tag 'nomadik-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
pinctrl/nomadik: Standardise Pinctrl compat string for Nomadik based platforms
ARM: nomadik: Standardise Nomadik STN8815 based Pinctrl compat string in the DTS
Conflicts:
arch/arm/boot/dts/ste-nomadik-s8815.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds machine support for the Allwinner A10s SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZDd
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.11-2' of git://github.com/mripard/linux into next/soc
From Maxime Ripard:
Allwinner platform additions, take 2
Adds machine support for the Allwinner A10s SoC
* tag 'sunxi-core-for-3.11-2' of git://github.com/mripard/linux:
ARM: sunxi: Add Allwinner A10s machine compatible
Depends on the sunxi/cleanup branch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRwBmFAAoJEAf03oE53VmQ66wH/Rs/7NV9kJZgpkLALi04Sw23
Mee2+wyu0NHPtJCu95FxsnP2JZD2NcoCA08iHiRg256BIFj/w62T5wgW672bt0oo
nuniLsqjPhbl7+j9mZPVZ2aWJtoo8gptKIuZxKIMsr4jfKd876CL3QoA/zjUNK5I
WAkYd6HOGRKPhIUy95sN0u4v6Clj43GNNp2RTsTnvUKg0v/gJJjERete0VDew/+P
WGK8VlHyvP/n5weSKIUTzFEBhBqfAYcqINejPCo6IzuUNseclJFcrnQBSKZb6KLP
RRMoB9kU4j2en9q7tpOFEtz/s1knc+c93YMkmjCkoDSRbgOENcppfYYdnVAznWk=
=gkn4
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into next/fixes-non-critical
From Nicolas Ferre:
Two non critical fixes that can go in 3.11.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRwBu9AAoJEAf03oE53VmQWokIAMLVbdBGfBOLV2O3rl/Yo07d
CD3ZG+eRzq4Rzms3qRnl57m9ESiPMVnkuvxdy3E7/ZKkihdUQKHMBGY9r1oHIjO2
KzA2QI5LRb6pOqtPH4HoTWmQYg8Tcg27ofjrTRfUDtG1jNENVMXfZCD5dF5V/ICx
vcfDuauqaLnJfsX+EO9Eedu90lBtP22M3dJqcZAozWPxM7FjUnEG4guvfDbo40lT
gj3xhwnx9BBpETyJFizcpW8nxPCANPIYhyPmw7SwvpVUjN487/O/yiR+kf4oXoQ4
vZFpXfOV6L4D/rg8G9gu9Lz6mXxnAyZDWkfQucfuMbIknK5Gg8FZCiH+fPoZZSg=
=INB9
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
One old board removal.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91: drop rm9200dk board support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=BH9M
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC changes for v3.11
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
* tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: remove unused transfer controller handlers
ARM: davinci: move private EDMA API to arm/common
ARM: davinci: remove __init atrribute from function declaration
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As noticed by Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>, commit
865e0527d2 ('arm: mvebu: avoid hardcoded virtual address in
coherency code') added a postcore_initcall() to register the bus
notifier that the mvebu code needs to apply correct DMA operations on
its platform devices breaks the multiplatform boot on other platforms,
because the bus notifier registration is unconditional.
This commit fixes that by registering the bus notifier only if we have
the mvebu coherency unit described in the Device Tree. The conditional
used is exactly the same in which the bus_register_notifier() call was
originally enclosed before 865e0527d2 ('arm: mvebu: avoid hardcoded
virtual address in coherency code').
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Current implementation of cpu_{suspend}/cpu_{resume} relies on the MPIDR
to index the array of pointers where the context is saved and restored.
The current approach works as long as the MPIDR can be considered a
linear index, so that the pointers array can simply be dereferenced by
using the MPIDR[7:0] value.
On ARM multi-cluster systems, where the MPIDR may not be a linear index,
to properly dereference the stack pointer array, a mapping function should
be applied to it so that it can be used for arrays look-ups.
This patch adds code in the cpu_{suspend}/cpu_{resume} implementation
that relies on shifting and ORing hashing method to map a MPIDR value to a
set of buckets precomputed at boot to have a collision free mapping from
MPIDR to context pointers.
The hashing algorithm must be simple, fast, and implementable with few
instructions since in the cpu_resume path the mapping is carried out with
the MMU off and the I-cache off, hence code and data are fetched from DRAM
with no-caching available. Simplicity is counterbalanced with a little
increase of memory (allocated dynamically) for stack pointers buckets, that
should be anyway fairly limited on most systems.
Memory for context pointers is allocated in a early_initcall with
size precomputed and stashed previously in kernel data structures.
Memory for context pointers is allocated through kmalloc; this
guarantees contiguous physical addresses for the allocated memory which
is fundamental to the correct functioning of the resume mechanism that
relies on the context pointer array to be a chunk of contiguous physical
memory. Virtual to physical address conversion for the context pointer
array base is carried out at boot to avoid fiddling with virt_to_phys
conversions in the cpu_resume path which is quite fragile and should be
optimized to execute as few instructions as possible.
Virtual and physical context pointer base array addresses are stashed in a
struct that is accessible from assembly using values generated through the
asm-offsets.c mechanism.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Colin Cross <ccross@android.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
On ARM SMP systems, cores are identified by their MPIDR register.
The MPIDR guidelines in the ARM ARM do not provide strict enforcement of
MPIDR layout, only recommendations that, if followed, split the MPIDR
on ARM 32 bit platforms in three affinity levels. In multi-cluster
systems like big.LITTLE, if the affinity guidelines are followed, the
MPIDR can not be considered an index anymore. This means that the
association between logical CPU in the kernel and the HW CPU identifier
becomes somewhat more complicated requiring methods like hashing to
associate a given MPIDR to a CPU logical index, in order for the look-up
to be carried out in an efficient and scalable way.
This patch provides a function in the kernel that starting from the
cpu_logical_map, implement collision-free hashing of MPIDR values by checking
all significative bits of MPIDR affinity level bitfields. The hashing
can then be carried out through bits shifting and ORing; the resulting
hash algorithm is a collision-free though not minimal hash that can be
executed with few assembly instructions. The mpidr is filtered through a
mpidr mask that is built by checking all bits that toggle in the set of
MPIDRs corresponding to possible CPUs. Bits that do not toggle do not carry
information so they do not contribute to the resulting hash.
Pseudo code:
/* check all bits that toggle, so they are required */
for (i = 1, mpidr_mask = 0; i < num_possible_cpus(); i++)
mpidr_mask |= (cpu_logical_map(i) ^ cpu_logical_map(0));
/*
* Build shifts to be applied to aff0, aff1, aff2 values to hash the mpidr
* fls() returns the last bit set in a word, 0 if none
* ffs() returns the first bit set in a word, 0 if none
*/
fs0 = mpidr_mask[7:0] ? ffs(mpidr_mask[7:0]) - 1 : 0;
fs1 = mpidr_mask[15:8] ? ffs(mpidr_mask[15:8]) - 1 : 0;
fs2 = mpidr_mask[23:16] ? ffs(mpidr_mask[23:16]) - 1 : 0;
ls0 = fls(mpidr_mask[7:0]);
ls1 = fls(mpidr_mask[15:8]);
ls2 = fls(mpidr_mask[23:16]);
bits0 = ls0 - fs0;
bits1 = ls1 - fs1;
bits2 = ls2 - fs2;
aff0_shift = fs0;
aff1_shift = 8 + fs1 - bits0;
aff2_shift = 16 + fs2 - (bits0 + bits1);
u32 hash(u32 mpidr) {
u32 l0, l1, l2;
u32 mpidr_masked = mpidr & mpidr_mask;
l0 = mpidr_masked & 0xff;
l1 = mpidr_masked & 0xff00;
l2 = mpidr_masked & 0xff0000;
return (l0 >> aff0_shift | l1 >> aff1_shift | l2 >> aff2_shift);
}
The hashing algorithm relies on the inherent properties set in the ARM ARM
recommendations for the MPIDR. Exotic configurations, where for instance the
MPIDR values at a given affinity level have large holes, can end up requiring
big hash tables since the compression of values that can be achieved through
shifting is somewhat crippled when holes are present. Kernel warns if
the number of buckets of the resulting hash table exceeds the number of
possible CPUs by a factor of 4, which is a symptom of a very sparse HW
MPIDR configuration.
The hash algorithm is quite simple and can easily be implemented in assembly
code, to be used in code paths where the kernel virtual address space is
not set-up (ie cpu_resume) and instruction and data fetches are strongly
ordered so code must be compact and must carry out few data accesses.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Colin Cross <ccross@android.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Replace /include/ by #include for da850 device tree files, in order to
use the C pre-processor, making use of #define features possible.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
* linus: (1465 commits)
ARM: tegra30: clocks: Fix pciex clock registration
lseek(fd, n, SEEK_END) does *not* go to eof - n
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
...
This revamps the device tree to fit with the new clock
implementation and brings it quite a bit closer to how
the hardware actually works.
After this the clock implementation knows about all
clock gates and will gate off all unused clocks at
boot time and save a bit of power.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvsJmAAoJEFBXWFqHsHzOHOIH/jjVCaAFdOskPI4d9qPPAt9C
5o0aJDjerzTm+vH2mbec2507fChaYrLybAypJUj6wDYRf03RhAgPXorY83Y+3WtG
SYz2UWza7MY8GeZv6e9tdrYS3JUSicFXPf8MsOcINsuyIub3dD96z36OqrnWZLFy
uH5V81e4gOHECd4PWIxmhdjwawqmwb/Pqzl0V3+vXi2JM07xrn7/SqlZ7VfUwM2q
DNhu5ugH7FtaFp75YrmTIhp6i+tovguRr0RIt6dnk/9gbJBQnV2Cw2MzdRPT12U5
bC79P7sojkKRtITcq9c1fnUNhkgc0+hS8HoezcQmzKMin6nFmVAh5wQFSlRJMJE=
=mZw+
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
ARM: imx: Remove mxc specific ulpi access ops
ARM: imx: add initial support for VF610
ARM: imx: add VF610 clock support
ARM: imx_v6_v7_defconfig: enable parallel display
ARM: imx: clk: No need to initialize phandle struct
ARM: imx: irq-common: Include header to avoid sparse warning
ARM: imx: Enable mx6 solo-lite support
ARM: imx6: use common of_clk_init() call to initialize clocks
ARM: imx6q: call of_clk_init() to register fixed rate clocks
ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
ARM: i.MX6: clk: add different DualLite MLB clock config
ARM i.MX5: Add S/PDIF clocks
ARM i.MX53: Add SATA clock
ARM: imx6q: clk: add the eim_slow clock
ARM: imx: remove MLB PLL from pllv3
ARM: imx: disable pll8_mlb in mx6q_clks
...
Conflicts:
arch/arm/Kconfig.debug (simple add/add conflict)
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* A bunch of new board additions, imx6sl-evk, vf610-twr, imx53-tx53,
imx53-m53evk and imx27-phytec-phycore
* Various pinctrl setting updates and additions
* Enable various on board peripherals, usb, audio, nor, display etc.
* Configure L2 cache data and tag latency from device tree
* Add imx-weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvsoqAAoJEFBXWFqHsHzOWCsIAIhbVAz9Q/HvRrrT2/viiu5G
S6/O16PbTqCmRPOgjnABGNOzRxo94/abhYT7gbGDz/zqAK2wEzEtUMwX8SXJbvl2
ynt4oX/QTgeQsZZXW+dCdet6XiBSJwfbFFo0c01pCBvPb7os739pO3u3CUvNeqKx
vsEfiq190PSPVL0FdfyLpQB+64ApUB1L/Ez9BaWmJjQYN2LWM0lxyvbC0SPo1vrw
eb8NJ7qz/qq3zXCKgD8LEvkfal4ZsezPYzap1sqKl1+T2aN4CsgzYaRra/wDv7BC
0ssW3+11StrwrbdwOEQRwiSU15fc9ckVldoFGlB+9HKTZxh80u0HmZRvFWbWo0E=
=jngF
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
imx device tree changes for 3.11:
* A bunch of new board additions, imx6sl-evk, vf610-twr, imx53-tx53,
imx53-m53evk and imx27-phytec-phycore
* Various pinctrl setting updates and additions
* Enable various on board peripherals, usb, audio, nor, display etc.
* Configure L2 cache data and tag latency from device tree
* Add imx-weim bus driver
* tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (82 commits)
ARM: dts: imx27: Add VPU devicetree node
ARM: mxc: fix gpio-ranges for VF610
ARM: dtsi: imx6qdl-sabresd: Enable WM8962 audio support
ARM: dtsi: imx6qdl-sabresd: Enable SSI2 and AUDMUX
ARM: dtsi: imx6qdl-sabresd: Add WM8962 CODEC support
ARM: dtsi: imx6qdl-sabresd: add a fixed regulator for WM8962
ARM: dtsi: imx6dl: Add a pinctrl for AUDMUX
ARM: dtsi: imx6q/imx6dl: Add a pinctrl for I2C1
ARM: dts: imx6qdl-sabresd: add clko1 iomux configuration
ARM: dts: Phytec imx6q pfla02 and pbab01 support
ARM: dts: imx6q: Add pinctrl for usdhc2 and enet
ARM: dts: imx27-phytec-phycore-rdk: Add MTD name for NOR flash
ARM: dts: imx27-phytec-phycore-rdk: Add SDHC support
ARM: dts: i.MX27: Add SDHC devicetree nodes
ARM: dts: i.MX27: Add DMA devicetree node
ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR
ARM: dts: imx6dl: add pinctrls for WEIM NOR
ARM: dts: imx6q: add pinctrls for WEIM NOR
ARM: dts: imx6qdl: add more information for WEIM
ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvsJmAAoJEFBXWFqHsHzOHOIH/jjVCaAFdOskPI4d9qPPAt9C
5o0aJDjerzTm+vH2mbec2507fChaYrLybAypJUj6wDYRf03RhAgPXorY83Y+3WtG
SYz2UWza7MY8GeZv6e9tdrYS3JUSicFXPf8MsOcINsuyIub3dD96z36OqrnWZLFy
uH5V81e4gOHECd4PWIxmhdjwawqmwb/Pqzl0V3+vXi2JM07xrn7/SqlZ7VfUwM2q
DNhu5ugH7FtaFp75YrmTIhp6i+tovguRr0RIt6dnk/9gbJBQnV2Cw2MzdRPT12U5
bC79P7sojkKRtITcq9c1fnUNhkgc0+hS8HoezcQmzKMin6nFmVAh5wQFSlRJMJE=
=mZw+
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
This is a dependency for imx/dt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvwUEAAoJEFBXWFqHsHzOZXgH/jYs9okBIb6UtYegmdGUinCD
VHJJT+RT8ceosMjBt+aBfpKplUG1X3OOoWbpU7Uv5JKNfY+0QbYTr4bdSE0YTF19
/ml5lCLLqW1MouErxIIe9yFrs4ZhZLLuW0Uy+ze7XVO/VPUlmJWYGU4D5gLcN+SH
aDdwAfe0SEydxWKp5euh6O2qPuuOro5/kUOPvYs6xaJj3marWkD9M6YyhaWvaFwF
2iUWzSd6dGabHRYwG2r38IlKMo6xncnu3b1NPifVMiPtiHFJ8t0SyTEGmpq19G+x
G6q0TneOUVIgH0PN4YQoCGOR6oAB52Z/dVTVlGx6LE6w9Q95wI3XNHltP5U+bF0=
=Oeyn
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
mxs device tree changes for 3.11:
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
* tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dt: Add Crystalfontz CFA-10057 device tree
ARM: mxs: dt: Add the Crystalfontz CFA-10055 device tree
ARM: cfa10049: Switch the chip select pin of the LCD controller
ARM: cfa10036: Add USB0 OTG port
ARM: dts: apf28dev: Add touchscreen support for APF28dev
ARM: mxs: Fix UARTs on M28EVK
ARM: cfa10036: dt: Change i2c0 clock frequency
ARM: dts: cfa10036: Change the OLED display to SSD1306
ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
ARM: mxs: Use soc bus infrastructure
ARM: dts: mx28: Adjust the digctl compatible string
ARM: mxs: Remove init_irq declaration in machine description
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=fstd
-----END PGP SIGNATURE-----
Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlG+ysgACgkQykllyylKDCENewCgk3LUwpMxepV1JOaNBmUJ0A09
jtMAnA395sve+FBxYjfM+nSAmbnl5RYl
=KBrZ
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx into next/dt
From Michal Simek:
arm: Xilinx Zynq dt changes for v3.11
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
* tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx:
arm: dt: zynq: Add support for the zed platform
arm: dt: zynq: Add support for the zc706 platform
arm: dt: zynq: Use 'status' property for UART nodes
arm: zynq: Remove board specific compatibility string
clk: zynq: Remove deprecated clock code
arm: zynq: Migrate platform to clock controller
clk: zynq: Add clock controller driver
clk: zynq: Factor out PLL driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch contains two fixes:
- Fix zynq smp code
- Do not specify init_irq ptr
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlG+pu4ACgkQykllyylKDCEEdwCcCfP7JyGt58zpJWPJOqiS9WQO
uLkAnjDZbMSgcHfOKZTrRgSdpdWnss1C
=njE0
-----END PGP SIGNATURE-----
Merge tag 'zynq-cleanup-for-3.11' of git://git.xilinx.com/linux-xlnx into next/cleanup
From Michal Simek:
arm: Xilinx Zynq cleanup patches for v3.11
This branch contains two fixes:
- Fix zynq smp code
- Do not specify init_irq ptr
* tag 'zynq-cleanup-for-3.11' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: Not to rewrite jump code when starting address is 0x0
ARM: zynq: Remove init_irq declaration in machine description
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=bzpe
-----END PGP SIGNATURE-----
Merge tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
This is a patch series that:
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being
* tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: basic PCIv3 device tree support
ARM: integrator: move static ioremapping into PCIv3 driver
ARM: integrator: move VGA base assignment
ARM: integrator: remap PCIv3 base dynamically
ARM: integrator: move V3 register definitions into driver
ARM: integrator: move PCI base address grab to probe
ARM: integrator: grab PCI error IRQ in probe()
ARM: integrator: convert PCIv3 bridge to platform device
ARM: integrator: merge PCIv3 driver into one file
ARM: pci: create pci_common_init_dev()
Documentation/devicetree: add a small note on PCI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
USB Host PHY clock on port 2 must be configured to 19.2MHz.
Provide this information.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
On Panda the +5V supply for DVI EDID is supplied by the
same regulator that poweres the USB Hub. Currently, the
DSS/DVI subsystem doesn't know how to manage this regulator
and so DVI EDID reads will fail if USB Hub is not enabled.
As a temporary fix we keep this regulator permanently enabled
on boot. This fixes the DVI EDID read problem.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for the USB host
pins.
HACK: The reset control need to be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
Signed-off-by: Roger Quadros <rogerq@ti.com>
[benoit.cousson@linaro.org: Add disclaimer about the reset control
inside changelog and code]
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Pull ARM fixes from Russell King:
"The larger changes this time are
- "ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page"
which fixes more data corruption problems with O_DIRECT
- "ARM: 7759/1: decouple CPU offlining from reboot/shutdown" which
gets us back to working shutdown/reboot on SMP platforms
- "ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect"
which fixes a shutdown regression found in v3.10 on Versatile
Express platforms.
The remainder are the quite small, maybe one or two line changes"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7759/1: decouple CPU offlining from reboot/shutdown
ARM: 7756/1: zImage/virt: remove hyp-stub.S during distclean
ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page
ARM: 7754/1: Fix the CPU ID and the mask associated to the PJ4B
ARM: 7753/1: map_init_section flushes incorrect pmd
ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect
The Armada 370 RD board has two internal mini-PCIe connectors. This
commit adds the necessary Device Tree informations to enable the usage
of those mini-PCIe connectors.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the required pin configuration support to EXYNOS5420
using pinctrl interface.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Tested-by : Sunil Joshi <joshi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add bandgap device DT entry for OMAP5 dtsi.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
[benoit.cousson@linaro.org: Fix alignement and use the macros
for IRQ attributes]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pinmux configurations for RGMII based CPSW ethernet to am335x-evm.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pinmux configurations for RGMII based CPSW ethernet to AM335x EVMsk.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pinmux configurations for MII based CPSW ethernet to am335x-bone.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Commit c971ff1 'leds: leds-pwm: Defer led_pwm_set() if PWM can sleep'
fixed a crash when using a trigger with a pwm-led provided by an
external chip. Now it is safe to add the default trigger according
to board-overo.c.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The LED is active low, not active high.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The Tobi expansion boards embeds a SMSC LAN8700 PHY. Add the
corresponding node into the DT. The regulators are not designed
to be turned off.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Some nodes in OMAP3 DTS now use edge or level sensitive interrupts.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
pxa27x-keypad includes matrix keys. Make use of matrix_keymap
for the matrix keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clkout2 comes out on the pad and is being used by various
external on-board peripherals like, Audio codecs and stuff.
So enable the clkout2 by default during init sequence itself.
Also, add the missing entry of "clkout2_ck" to the clock table.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Represent debugSS clock interface as provided in
CM_WKUP_DEBUGSS_CLKCTRL register, includes
- Clock gate for optional DEBUG_CLKA and DBGSYSCLK
- Clock Mux for TRC_PMD and STM_PMD
- Clock divider for STM and TPIU
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add Palmas MFD node and the regulator nodes for OMAP5.
The node definitions are based on: https://lkml.org/lkml/2013/6/6/25
Boot tested on omap5-uevm board.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
PWM output from ecap2 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales with
inverse polarity.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
PWM output from ecap0 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add PWMSS device tree nodes in relation with ECAP & EHRPWM DT nodes to
AM33XX SoC family. Also populates device tree nodes for ECAP & EHRPWM by
adding necessary properties like pwm-cells, base reg & set disabled as
status.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the bandgap entry for OMAP4430 devices.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
[benoit.cousson@linaro.org: Add blank line and fix reg presentation]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
On most OMAP3 platforms, the twl4030 IRQ line is connected to the
SYS_NIRQ line on OMAP. Add another DTS include file
(twl4030_omap3.dtsi) for boards that hook up the twl4030 this way
to include.
This allows RTC wake from off-mode to work again on OMAP3-based
platforms with twl4030. Tested on 3530/Beagle, 3730/Beagle-xM,
3530/Overo, 3730/Overo-STORM.
Special thanks to Florian Vaussard for suggesting use of preprocessor
feature.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using the gpio-keys bindings, configure the user button on Beagle
boards. Since the user button is enabled as a wakeup source, also
ensure the GPIO pin is mux'd correctly and has IO ring wakeups enabled,
so it can also wakeup from off mode.
Special thanks to Florian Vaussard for suggesting the preprocessor
feature.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Ensure the console uart (UART3) on these boards is mux'd correctly, and
IO ring wakeup is enabled.
This is needed for serial console wakeups when using DT boot.
Thanks to Florian Vaussard for suggestion to use preprocessor
features.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Booting omap5 uevm results in the following error
"did not get pins for uart error: -19"
This happens because omap5 uevm dts file is not adapted
to use uart through pinctrl framework.
Populate uart pinctrl data to get rid of the error.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add support for blue LED 1 off of GPIO 153.
Make the LED a heartbeat LED
Configure the MUX for GPIO output.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Provide the RESET regulators for the USB PHYs, the USB Host
port modes and the PHY devices.
Also provide pin multiplexer information for the USB host
pins.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.
Renaming the board dts file and adding the following cleanups.
* There are no devices connected on I2C 2,3,4 buses. So remove
the pinmux data for the same.
* OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
is not supported with DDR3 memories. Because of DDR3 phy limitation
the voltage change across DVFS and all shadow registers for DVFS on
DDR3 is not supported. Hence the emif kernel driver is not required,
so removing the DDR3 device file and emif nodes for uevm.
* Keypad is not supported on uevm. So remove the device node.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
When making the dtbs target on OMAP/AM35xx, some trees are not
built.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for AM33XX and AM35XX device tree
files, in order to use the C pre-processor, making use of #define
features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
DT source (minimal) for AM4372 SoC to represent AM43x SoC's. Those
represented here are the minimal DT nodes necessary to get kernel
booting.
In DT nodes, "ti,hwmod" property has not been added, this would be
added along with PRCM support for AM43x.
Signed-off-by: Ankur Kishore <a-kishore@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Update the dt property ti,audpwron-gpio to use the
gpio macro definition for GPIO_ACTIVE_HIGH.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
are different.
A1-A3 = gpio_wk7
ES = gpio_110
There is no change to LED D2
Abstract away the pinmux and the LED definitions for the two boards into
the respective DTS files.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use the constants defined in include/dt-bindings/interrupt-controller/
to enhance readability.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
GPMC controller on AM335x-EVM has a NAND flash connected to it.
This patch updates following in am335x-evm.dts:
- adds nandflash specific pin-mux configs
- adds nand node as child of GPMC contoller, with information about
NAND flash interface, NAND partition table, ECC scheme, elm handle id.
- updates GPMC node for newer GPMC DT properties added in linux-3.10.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
ELM hardware engine is used for locating bit-flips in NAND data
This patch is required for working of hardware based NAND ECC schemes
with DT support.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEP COM Module has an 512MB NAND flash memory.
Add a device node for this NAND and its partition layout.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEPv2 board has an 512MB NAND flash memory.
Add a device node for this NAND and its partition layout.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEPv2 board has an SMSC LAN9221i ethernet chip connected to
the OMAP3 processor though the General-Purpose Memory Controller.
This patch adds a device node for the ethernet chip as a GPMC child
and all its dependencies (regulators, GPIO and pin muxs).
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
xdma_event_intr1.clkout2 pad can be used to source clock
from either 32K OSC or any of the PLL (except MPU) outputs.
On the existing AM335x based boards (EVM, EVM-SK and Bone),
this pad is used to feed the clock to audio codes.
So, this patch configures the pinmux to get clkout2 on the pad.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for UART0 device nodes in all
board specific DT files.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
With DT support, where naming convention is based on base-addr
and not id, so we should follow TRM/Spec numbering label.
This patch changes UART numbering as per TRM, as uart0-5.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Now gpio-leds driver is using devm_pinctrl_get_select_default()
api to set default pinmux configuration required for the
functionality of the driver, so this patch moves respective
pinctrl binding inside leds node.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for I2C device nodes in all
board specific DT files (as per current usage),
EVM: Both i2c0 and i2c1
EVM-SK and Bone: Only i2c0
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The carveouts that have been reserved for multimedia usecases
are not being used currently by any driver and so have been
cleaned up. Memory will be allocated runtime through CMA for
enabling the multimedia usecases.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
This reverts commit 55a68c23e0.
In order to avoid a collision with dw_apb_timer changes in
the arm-soc tree, revert this change.
I'm leaving it to the arm-soc folks to sort out if they want
to keep the other side of the collision or if they're just going
to back it all out and try again during the next release cycle.
Reported-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Conflicts:
arch/arm/kernel/smp.c
Please pull these miscellaneous LPAE fixes I've been collecting for a while
now for 3.11. They've been tested and reviewed by quite a few people, and most
of the patches are pretty trivial. -- Will Deacon.
Extend the soft reset support for EXYNOS5420 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The location at which the boot address is specified for secondary
CPUs of EXYNOS5420 is SYSRAM base + 4. Update the cpu_boot_reg
function accordingly.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add initial device tree nodes for EXYNOS5420 SoC and SMDK5420 board.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use chipid[27:20] bits to identify the EXYNOS family while setting
up the serial port during the uncompression setup. This uses four
additional bits of chipid to identify the EXYNOS family since this
is required for identifying EXYNOS5420 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
EXYNOS5420 is new SoC in Samsung's Exynos5 SoC series. Add
initial support for this new SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Instead of having to specify the number for CPUs in EXYNOS5250 in
platsmp.c file, let the number of CPUs be determined by having this
information listed in EXYNOS5250 device tree file.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In preparation of adding support for EXYNOS5420, which has many
peripherals similar to EXYNOS5250, a new common EXYNOS5 device tree
source file is created out of the exising EXYNOS5250 device tree
source file. Only the common nodes required for basic boot up on
EXYNOS5420 based boards are moved into this new file and the rest
of the common nodes would be moved subsequently.
EXYNOS5440 SoC is quite different from EXYNOS5250 and EXYNOS5420.
Hence it is not possible to reuse "exynos5.dtsi" for EXYNOS5440.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
This patch reads the cpuid part number and if it matches with
cortex-A9, calls scu_enable()
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously if you had MACH_EXYNOS5_DT but not MACH_EXYNOS4_DT you'd be
missing the pincontrol definitions. Move PINCTRL selects to the arch
level since we should be enabling the code for all exynos variants.
Update the PINCTRL descriptions to indicate that PINCTRL_EXYNOS is not
for exynos5440. Also add basic dependencies for the PINCTRL_EXYNOS
kernel config.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables support for XHCI on exynos5 series of SOCs,
to support host side USB 3.0 support.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add clock lookup information for i2s controllers on exynos5250 SoC.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Audio subsystem introduced in s5pv210 and exynos platforms
which has a internal clock controller. This patch adds a node
for the same on exynos5250.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Replace /include/ (dtc) with #include (C pre-processor) for all
Samsung DT files
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since there are no remaining users of this header, it can be safely
dropped.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since all platforms have been moved to the new watchdog reset driver,
the legacy code can be removed safely.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves all platforms using the legacy watchdog reset helper
function to the new watchdog reset driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a watchdog reset driver that can be used on Samsung SoCs
that do not provide dedicated reset method. It replaces the legacy
helper function that relies on static IO mapping.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds local definitions of required watchdog registers and
bitfields to the uncompress header, allowing to remove the dependency on
plat/regs-watchdog.h header and the ugly hack to replace virtual with
physical addresses.
In addition, it fixes reboot on decompression failure feature, due to
the mentioned ugly hack not working anymore (the macro being redefined
got renamed, without fixing this code).
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 9ee51f01ee (tty: serial/samsung: make register definitions
global) removed the S3C2410_PA_UARTX defines that the newly merged
s3c2416 dt support still expected.
So update mach-s3c2416-dt.c to use the S3C24XX_PA_UART constant until
we have support for the common clock framework the the s3c2416-dt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since uart_base can be set dynamically in arch_detect_cpu(), there is no
need to have a copy of all code locally, just to override UART base
address.
This patch removes any duplicate code in uncompress.h variant of s5p64x0
and implements proper arch_detect_cpu() function to initialize UART with
SoC-specific parameters.
While at it, replace hard-coded register address with macro.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For mach-exynos, uart_base is a pointer and the value is calculated
in the machine folder. For other machines, uart_base is defined as
a macro in platform directory. For symmetry, the uart_base macro
definition is removed and the uart_base calculation is moved to
specific machine folders.
This would help us consolidating uncompress subroutine for s5p64x0.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes remaining small bits of unused code that was left
after removing non-DT support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since Exynos is now supporting only DT-based boot, the old L2X0
initialization code is not needed anymore, so exynos4_l2x0_cache_init()
can be greatly simplified.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since there is no board specific mapping needed on Exynos,
exynos_init_io() can be simplified and used as map_io callback for both
Exynos4 and Exynos5.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since both exynos4_init_irq() and exynos5_init_irq() are just calling
irqchip_init(), there is no need for them to exist any more, since this
is the default that is called when init_irq callback is not specified.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes mach/regs-usb-phy.h header, which is not used
anywhere in the kernel.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes all the unused base addresses from mach/map.h header,
leaving only addresses of IPs that currently use static IO mapping or
need the address hardcoded, like low level debug UART.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since Exynos now uses CONFIG_SPARSE_IRQ and all remaining users of this
header has been fixed, we can safely remove it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds selection of CONFIG_SPARSE_IRQ for ARCH_EXYNOS, since it
is required by multiplatform and allows to remove the legacy mach/irqs.h
header.
To make this possible, a dummy IRQ_EINT_BIT macro is added to pm-core.h
header to allow plat-samsung/pm.c compile. This macro is irrelevant for
Exynos and will be removed after reworking Samsung pm code for
multiplatform compatibility.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This allows to bypass compilation of static platform device and resource
definitions that require interrupts and base addresses to be defined
statically.
Cc: Jeongtae Park <jtp.park@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Contents of this header are not used any more and can be safely removed.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes mach/gpio.h header that is not required any more on
Exynos.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now since SAMSUNG_ATAGS is no longer selected for ARCH_EXYNOS, we can
safely remove the remaining setup code.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes selection of several legacy Kconfig symbols from
ARCH_EXYNOS to bypass compilation of code used only for ATAGS based
boot.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since it is illegal to include mach/ headers from source files outside
of respective mach-* directory and DT-only Samsung platforms might not
have all of them anyway, this patches makes inclusion of them
conditional, based on CONFIG_SAMSUNG_ATAGS.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
After removing support for ATAGS based boot on Exynos, there is not much
that can be shared between Exynos and other S5P platforms. This patch
makes Exynos a standalone Samsung platform, not using PLAT_S5P.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds new Kconfig symbols, SAMSUNG_PM_GPIO and S5P_IRQ_PM that
get enabled when GPIO_SAMSUNG, PM and S5P_PM are enabled, but only if
SAMSUNG_ATAGS is selected.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds several compatibility definitions that are not relevant
for Exynos, but are required by Samsung PM core.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Kconfig entry that selects whether legacy Samsung GPIO
driver should be built or not. For platforms that support only DT based
boot, the new pinctrl driver is used and so the old one is not needed.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The LDO for LCD driver is currently not handled by any of the drivers.
This disables the LDO during booting time. To fix this, the LDO
is forced to enabled always.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Many of the boards use GPIO-mapped buttons for generic input.
For Arndale board, these buttons also serve as wakeup source.
And the issues reported in commit 522ccdb6fd ("ARM: dts:
Disable the RTC by default on exynos5") are no longer reproduced
on EXYNOS5250 based systems. Hence it would be better to re-enable
RTC support for EXYNOS5250.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
[mturquette@linaro.org: ack on RTC enabling]
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
GPMC is hardware controller for external memory interfaces.
This patch adds suspend/resume support for GPMC driver.
It also preserves GPMC register configurations across device low-power states
in which GPMC hardware can be powered-off.
gpmc_suspend()/gpmc_resume() are called by default by core PM framework as part
of driver's runtime PM callbacks.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2+ platforms, USB support needs physical layer signalling and
the NOP USB Transceiver driver since v3.10. This patch enables USB_PHY
and NOP_USB_XCEIV in omap2plus_defconfig. These two are harmless to
the kernel stability, and useful since they are required for USB and
Ethernet (over USB) support.
We do not enable USB_EHCI_HCD here because all features aren't fully
supported yet.
This patch applies to Linux 3.10-rc3.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for Tahvo.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: left out extcon to remove dependency to USB patches]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On 37xx EVM non-dt boot fails with current mainline,
because of broken GPIO numbering in the board file
that uses hardcoded GPIOs.
So marking omap3_evm_display_init() with CONFIG_BROKEN
for now as suggested by Tony as per the below link:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg90399.html
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The reset GPIO should be set for the SMSC911x, otherwise the controller
will not work and probing will fail. In the case of the tobi-duo
expansion board, the second controller shares the same GPIO, thus no
more changes are required (not tested).
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Layout of DEV_FEATURE register (offset = 0x604) is different
between TI81xx and AM33xx device, so create separate function
which will check for features available on specific AM33xx SoC
and set the flags accordingly.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use devm_ioremap_resource instead of reques_mem_region()/ioremap(),
devm_request_irq() instead of request_irq() and kzalloc() calls to
devm_kzalloc().
This ensures more consistent error values and simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[nsekhar@ti.com: add missing err.h include]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This board is impossible to found anymore.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
currently Tegra cpufreq driver gets built based on ARCH_TEGRA, which doesn't
depend on nor select CPU_FREQ itself, so:
select CPU_FREQ_TABLE if CPU_FREQ
... isn't guaranteed to fire.
The correct solution seems to be:
* Add CONFIG_ARM_TEGRA_CPUFREQ to drivers/cpufreq/Kconfig.arm.
* Make that Kconfig option selct CPU_FREQ_TABLE.
* Make that Kconfig option be def_bool ARCH_TEGRA.
* Modify drivers/cpufreq/Makefile to build tegra-cpufreq.c based on that.
* Remove all the cpufreq-related stuff from arch/arm/mach-tegra/Kconfig.
That way, tegra-cpufreq.c can't be built if !CPU_FREQ, and Tegra's
cpufreq works the same way as all the other cpufreq drivers.
This patch does it.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
CPUFreq driver of this platform uses APIs from freq_table.c and so must select
CPU_FREQ_TABLE.
Cc: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
CPUFreq driver of this platform uses APIs from freq_table.c and so must select
CPU_FREQ_TABLE.
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Because MT_DEVICE is not executable in armv7, we change
the internal SRAM memory type to MT_MEMORY_NONCACHED.
As it seems that caching this internal SRAM memory is not necessary,
we chose the this memory type.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes:
arch/arm/mach-at91/built-in.o: In function `ksz9021rn_phy_fixup':
:(.text+0x1174): undefined reference to `mdiobus_write'
:(.text+0x1188): undefined reference to `mdiobus_write'
:(.text+0x119c): undefined reference to `mdiobus_write'
:(.text+0x11b0): undefined reference to `mdiobus_write'
arch/arm/mach-at91/built-in.o: In function `sama5_dt_device_init':
:(.init.text+0x1e34): undefined reference to `phy_register_fixup_for_uid'
when CONFIG_PHYLIB is not selected.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds required structures for powerdomain initialization on
the ti816x. It is impossible to use omap3430 structures in order to
initialize powerdomains on ti816x, because there are big differences
between PRCM module base address offsets on these CPUs.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently omap3xxx_check_revision() detects ES1.0 and ES1.1 only,
this patch extends it by adding ES2.0 and ES2.1 versions support.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e45600107b (Merge tag 'msm-cleanup-for-3.11' of
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into
next/cleanup) incorrectly resolved a merge conflict, resulting in a
node address that doesn't match the register address.
Fix this node address.
Signed-off-by: David Brown <davidb@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Minimal machine and device-tree support with arch_timers and console UART
- Reboot hook using PLL reset
- Low level debug support using UART
- SMP boot support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pkFT
-----END PGP SIGNATURE-----
Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
From Santosh Shilimkar:
SOC support for Keystone II devices:
- Minimal machine and device-tree support with arch_timers and console UART
- Reboot hook using PLL reset
- Low level debug support using UART
- SMP boot support
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: Enable SMP support on Keystone machines
ARM: keystone: Add minimal TI Keystone platform support
ARM: dts: keystone: Add minimal Keystone SOC device tree data
Signed-off-by: Olof Johansson <olof@lixom.net>
When changing the name of Ether platform device in the commit c02f846938 (ARM:
shmobile: r8a7778: fix Ether device name), I completely forgot that there's also
platform device name used in bockw_pinctrl_map[], so the commit "ARM: shmobile:
BOCK-W: add Ether support" went in with the old "sh-eth" device name. Now change
it to "r8a777x-ether" in accordance with the commits that are now in the 'net-
next.git' repository, otherwise BOCK-W Ether support won't work in 3.11.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The convention for Device Tree node names is <device>@<hex-address>, where
the part after '@' shouldn't contain the "0x" prefix. Fix the sh73a0.dtsi
DT names.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add definitions in arch/arm/mach-omap1/dma.h are now removed so remove
the file and include statements from dma.c and lcd_dma.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap-ir.c driver has never been upstream and was also removed from
linux-omap.git four years ago (See linux-omap.git commit efd1e3f
("REMOVE OMAP LEGACY CODE: Reset drivers/net/irda to mainline")).
Therefore remove needless device registration from a few board files
and delete thus to be unused arch/arm/mach-omap1/include/mach/irda.h
and unused OMAP_DMA_UART3_* definitions from dma.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similarly than with OMAP2 there are many DMA channel definitions that have
been moved or redefined in drivers using them and we can remove them from
dma.h.
There is exception with MMC that arch/arm/mach-omap1/devices.c is using
MMC DMA channel definitions for setting platform data but those can be well
replaced with numeric values.
Remove dma.h include from arch/arm/mach-omap1/devices.c and use a script
below for dropping duplicated definitions and for replacing definitions
with DMA channel numbers.
grep '#define OMAP_DMA' arch/arm/mach-omap1/dma.h | while read -r i; do \
DDEF=`echo $i |cut -d ' ' -f 1-2`; \
DEF=`echo $DDEF |cut -d ' ' -f 2`; \
CH=`echo $i |cut -d ' ' -f 3`; \
if [ `git grep -c "$DDEF" |wc -l` -gt 1 ]; then \
echo "removing" $DEF; \
sed -i "s/${DEF}/${CH}/" arch/arm/mach-omap1/devices.c; \
sed -i "/${DDEF}/d" arch/arm/mach-omap1/dma.h; \
fi; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/mach-omap1/mcbsp.c is only place where OMAP1 McBSP DMA channel
definitions are set. We may well use numerical values there and get rid
of their definitions in arch/arm/mach-omap1/dma.h.
Remove dma.h include from arch/arm/mach-omap1/mcbsp.c and use following
script for replacing definitions with DMA channel number:
egrep '#define OMAP_DMA_MCBSP' arch/arm/mach-omap1/dma.h | cut -f 1,3 \
| while read i; do \
DEF=`echo $i |cut -d ' ' -f 2`; \
CH=`echo $i |cut -d ' ' -f 3`; \
echo "removing" $DEF; \
sed -i "s/${DEF}/${CH}/" arch/arm/mach-omap1/mcbsp.c; \
sed -i "/${DEF}/d" arch/arm/mach-omap1/dma.h; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All definitions in arch/arm/mach-omap2/dma.h are removed so it can be
removed now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last remaining DMA channel definitions in arch/arm/mach-omap2/dma.h
are used only by omap_hwmod_2xxx_3xxx_ipblock_data.c and
omap_hwmod_3xxx_data.c. Remove them by using directly DMA channel number in
hwmod data and drop definitions with a following script:
egrep '#define [OMAP|AM35XX].*DMA' arch/arm/mach-omap2/dma.h | cut -f 1,3 \
| while read i; do \
DEF=`echo $i |cut -d ' ' -f 2`; \
CH=`echo $i |cut -d ' ' -f 3`; \
echo "removing" $DEF; \
sed -i "s/${DEF}/${CH}/" arch/arm/mach-omap2/omap_hwmod_*.c; \
sed -i "/${DEF}/d" arch/arm/mach-omap2/dma.h; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many DMA channel definitions in arch/arm/mach-omap2/dma.h have been moved or
redefined in drivers without removing them from dma.h. Remove those with a
script below:
egrep '#define OMAP.*DMA' arch/arm/mach-omap2/dma.h \
|cut -f 1 |cut -d ' ' -f 1-2 | while read -r i; do \
if [ `git grep -c "$i" |wc -l` -gt 1 ]; then \
echo "removing" $i; \
sed -i "/${i}/d" arch/arm/mach-omap2/dma.h; \
fi; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These became unused after commit 660ffd6
("ARM: OMAP2xxx: hwmod: Convert AES crypto devcie data to hwmod").
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Given p = pdev->dev.platform_data; and
d = p->dma_attr;
the freeing of either one of these by the driver
seems just plain wrong.
Get rid of them in the .probe failure path as well as the
.remove.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once a free channel is found, the check for dev_id == 0 does
not make any sense. Get rid of it.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix build on OMAP, the irqs are undefined on AM33xx.
These error interrupt handlers were hardcoded as disabled
so since they are unused code, simply remove them.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add basic SMP support for Keystone machines. This does not
include support for CPU hotplug for now.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Texas Instruments Keystone family of multi-core devices are
based on ARM Cortex A15. Patch adds basic definitions for a
new Keystone sub-architecture in ARM.
The TCI66xxK2H Communications Infrastructure Keystone SoCs
are member of the C66x family based on TI's new KeyStone 2
multi-core SoC Architecture designed specifically for high
performance wireless and networking infrastructure applications.
The SOCs contains many subsystems like Cortex A15 ARM CorePacs,
C66XX DSP CorePacs, MSMC memory controller, Tera Net bus,
IP Network, Navigator, Hyperlink, 1G/10G Ethernet, Radio layers
and queue based communication systems.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add minimal device tree data for Keystone2 based SOCs. Patch
contains mainly ARM related SOC data and nothing about EVM specific
yet.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
By default the exynos RTC is disabled. Enable it for snow. There's
also an external RTC on the max77686 PMIC but we haven't yet enabled
that.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The issues reported in commit 522ccdb6fd ("ARM: dts: Disable the RTC
by default on exynos5") are no longer reproduced on EXYNOS5250 based
Arndale board. Hence re-enabling RTC support for Arndale board.
This is helpful for testing S2R on Arndale board.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since the pdma works only in secure mode, accessing the same
in hypervisor mode gives an abort. As we are not using pdma
anywhere, removing the same.
Signed-off-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since ssdk5440 and sd5v1 have 8GiB memory, this patch
updates bootargs for them.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates cpu frequency level from 1500 to 800MHZ in steps
of 100MHZ. The corresponding voltage(in uV) is also added.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the required regulator supplies and properties
for wm8994 codec on smdk5250 board.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables the SPI in EXYNOS5440 SoC. The NOR
Flash can be accessed by enabling the spi interface
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add comments to machine_shutdown()/halt()/power_off()/restart() that
describe their purpose and/or requirements re: CPUs being active/not.
In machine_shutdown(), replace the call to smp_send_stop() with a call to
disable_nonboot_cpus(). This completely disables all but one CPU, thus
satisfying the requirement that only a single CPU be active for kexec.
Adjust Kconfig dependencies for this change.
In machine_halt()/power_off()/restart(), call smp_send_stop() directly,
rather than via machine_shutdown(); these functions don't need to
completely de-activate all CPUs using hotplug, but rather just quiesce
them.
Remove smp_kill_cpus(), and its call from smp_send_stop().
smp_kill_cpus() was indirectly calling smp_ops.cpu_kill() without calling
smp_ops.cpu_die() on the target CPUs first. At least some implementations
of smp_ops had issues with this; it caused cpu_kill() to hang on Tegra,
for example. Since smp_send_stop() is only used for shutdown, halt, and
power-off, there is no need to attempt any kind of CPU hotplug here.
Adjust Kconfig to reflect that machine_shutdown() (and hence kexec)
relies upon disable_nonboot_cpus(). However, this alone doesn't guarantee
that hotplug will work, or even that hotplug is implemented for a
particular piece of HW that a multi-platform zImage runs on. Hence, add
error-checking to machine_kexec() to determine whether it did work.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Zhangfei Gao <zhangfei.gao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch corrects the base address of pinctrl_3 on Exynos5250
platform.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I were
discussing today until we've reached a conclusion/that's had some more
review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now that
you've merged that. I've included the fix for limiting MPU to CPU_V7.
Now that there is a way to tell the powerdomain core about
missing voltage domain auto-scaling control in SoCs', get rid of the dummy
voltage domain data populated for AM33xx devices.
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Afzal Mohammed <afzal@ti.com> # am335x evm
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The powerdomain framework currently expects all powerdomains to be associated with
a corresponding voltagedomain. For some SoCs' (like the already existing AM33xx
family, or for the upcoming AM437x and DRA7 SoCs') which
do not have a Voltage controller/Voltage Processor (neither the SR I2C
bus to communicate with the PMIC) there is no need for a Powerdomain to have
a voltage domain association since there is no auto-scaling of voltages possible
using the voltage FSM.
Extend the arch operations to add an api which the powerdomain core can
then use to identify if a voltdm lookup and association for a powerdomain
is really needed.
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Afzal Mohammed <afzal@ti.com> # am335x evm
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The support for the MPU is currently implemented only for R-class
(PMSAv7/R). Since the merge of V7M support in to the kernel it is possible
to select MPU support on V7M.
This patch ensures that until MPU support for M-class processors is
implemented, the MPU can only be selected with R-class CPUs
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Without an MMU it is possible for userspace programs to start executing code
in places that they have no business executing. The MPU allows some level of
protection against this.
This patch protects the vectors page from access by userspace processes.
Userspace tasks that dereference a null pointer are already protected by an
svc at 0x0 that kills them. However when tasks use an offset from a null
pointer (eg a function in a null struct) they miss this carefully placed svc
and enter the exception vectors in user mode, ending up in the kernel.
This patch causes programs that do this to receive a SEGV instead of happily
entering the kernel in user-mode, and hence avoid a 'Bad Mode' panic.
As part of this change it is necessary to make sigreturn happen via the
stack when there is not an sa_restorer function. This change is invisible to
userspace, and irrelevant to code compiled using a uClibc toolchain, which
always uses an sa_restorer function.
Because we don't get to remap the vectors in !MMU kuser_helpers are not
in a defined location, and hence aren't usable. This means we don't need to
worry about keeping them accessible from PL0
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
CC: Nicolas Pitre <nico@linaro.org>
CC: Catalin Marinas <catalin.marinas@arm.com>
Allows the user to select MPU support when compiling for ARM processors
that support the PMSAv7.
This ensures that CONFIG_SMP depends on the MPU in the case that no MMU
is present.
CONFIG_SMP_ON_UP is not implemented for nommu, so introduce an MMU
dependency there.
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This switches the code using a local remapping of the
system controller to enable the U300 board to be
self-powered over to making the U300-specific syscon
compatible with the MFD generic syscon driver, selecting
the generic syscon driver, and augmenting the board
power code to pick the regmap and manipulate the syscon
from the regmap side of things.
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable MMC_UNSAFE_RESUME to be accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.
ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This deletes the dependency on any platform data for
the COH901 pin controller. There is only one user in the
kernel, and if we at some point want to support more
variants, they shall provide their variant info through
the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the last of the U300 clocks to being probed from
the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the slow, fast, AHB bridge and "rest" clocks on
the U300 system controller over to registration from the
device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the fixed and fixed-factor clocks in the U300
platform to register themselves from the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the core file is the only one actually using any
of the base addresses, we can delete that header and move
the base address definitions into the one and only core
file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree node for the U300 system controller
and remaps this dynamically instead of using hard-coded
virtual addresses. The board power set-up code is altered
to fetch a reference to the syscon using ampersand <&syscon>
notation. This way of passing a pointer to the syscon will
also be used by the clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removing some boilerplate by using module_spi_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two files remain in <mach/*> for U300: timex.h and
uncompress.h. The former is done away with by using
defaults, the latter is unused in multiplatform.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we removed our dependency on <mach/*> the U300
can be converted to mutliplatform. Remove the invalid restriction
that U300 would not support AUTO_ZRELADDR (it does) and update
the defconfig in the process.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This register base file is now only used in the machine
itself so move it down into mach-u300.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All IRQs are now obtained from the device tree, and this file
is unused, so delete it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of the <mach/syscon.h> header as a prerequisite for
multiplatform support. Do this by pushing the registers down
to their respective drivers and deleting the unused remainder.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This rids the dependency to <mach/hardware.h> (which is an
implicit dependency to <mach/u300-regs.h>) from the U300
debug macro. Take this opportunity to update the file
header.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have now transferred all the U300 peripherals to the device
tree, so we just select USE_OF, and delete all static board data,
then require that this platform shall be booted using the device
tree and nothing else.
This gets rid of the MMCI (PL180), PL022, and serial PL011
platform data entries and more.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the U300 FSMC flash controller from the
device tree, and defines the three partitions. Skip the
BBT scan as in the current platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This probes the U300 dummy-spichip from the device tree
and adds the apropriate node to the tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the PL022 PrimeCell from the U300 device
tree. We make a new copy of the platform data for the
device tree boot path, as the old platform data is in an
older file which will be going away.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the COH 901 318 DMA controller to the U300
device tree. All devices now converted to device tree
so far will start to find their DMA channels.
Note that the U300 is not yet using the device tree
to obtain DMA channels, but this is a first step.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds DMA channel assignments to the MMC/SD-controller
and the two UARTs already in the U300 device tree, as we
have now defined a way to obtain DMA channels from the
device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the U300 MMC/SD card slot from the device
tree boot. No other changes needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for setting up the board power from the
device tree on the U300. We use a board-specific node in the
device tree for the S365 board and bind a regulator for the
board power to this node.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure hyp-stub.S gets removed during make distclean,
this left over file was introduced in commit:
424e599 ARM: zImage/virt: hyp mode entry support for the zImage loader
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit f8b63c1 made flush_kernel_dcache_page a no-op assuming that
the pages it needs to handle are kernel mapped only. However, for
example when doing direct I/O, pages with user space mappings may
occur.
Thus, continue to do lazy flushing if there are no user space
mappings. Otherwise, flush the kernel cache lines directly.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> # 3.2+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit fixes the ID and mask for the PJ4B which was too
restrictive and didn't match the CPU of the Armada 370 SoC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This bug was introduced in commit e651eab0.
Some v4/v5 platforms failed to boot due to this.
Signed-off-by: Po-Yu Chuang <ratbert.chuang@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Cortex-A9 before version r1p0, the LoUIS bit field of the CLIDR
register returns zero when it should return one. This leads to cache
maintenance operations which rely on this value to not function as
intended, causing data corruption.
The workaround for this errata is to detect affected CPUs and correct
the LoUIS value read.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is an external component and may or may not be there, while the
internal clock always works.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds support for HSCIF0 and HSCIF1 on the r8a7790.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
[ horms+renesas@verge.net.au this is the setup-r8a7790.c
which I somehow miss-applied as part of another patch.
The clock-r8a7790.c portion of this patch has already been merged. ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT fragment for the Zed Zynq platform and a corresponding
target to the Makefile
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a DT fragment for the zc706 Zynq platform and a corresponding
target to the Makefile.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the default status for UARTs to disabled in the zynq-7000.dtsi file
and let board dts files enable the UARTs on demand.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is not necessary to have board specific compatibility strings
in the platform code. The board dts files can use the more generic
'xlnx,zynq-7000' string.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bandgap is a device used to measure temperature on electronic
equipments. It is widely used in digital integrated circuits. It is
based on the dependency between silicon voltage and temperature.
This patch introduce HAS_BANDGAP config entry. This config is a boolean
value so that arch code can flag if they feature a bandgap device.
This config entry follows the same idea behind ARCH_HAS_CPUFREQ.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Fabio Stevam <festevam@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When scheduling an mm on a CPU where it hasn't previously been used, we
flush the icache on that CPU so that any code loaded previously on
a different core can be safely executed.
For cores with hardware broadcasting of cache maintenance operations,
this is clearly unnecessary, since the inner-shareable invalidation in
__sync_icache_dcache will affect all CPUs.
This patch conditionalises the icache flush in switch_mm based on
cache_ops_need_broadcast().
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Albin Tonnerre <albin.tonnerre@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When zImage is loaded into RAM at a low address but TEXT_OFFSET
is set higher, we risk overwriting ourself with the page table
needed to turn on the cache as it is located relative to the relocation
address. Let's defer the cache setup after relocation in that case.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Stephen Boyd <sboyd@codeurora.org>
Tested-by: Stephen Boyd <sboyd@codeurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An exclusive store instruction may fail for reasons other than lock
contention (e.g. a cache eviction during the critical section) so, in
line with other architectures using similar exclusive instructions
(alpha, mips, powerpc), retry the trylock operation if the lock appears
to be free but the strex reported failure.
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Running an OABI_COMPAT kernel on an SMP platform can lead to fun and
games with page aging.
If one CPU issues a swi instruction immediately before another CPU
decides to mkold the page containing the swi instruction, then we will
fault attempting to load the instruction during the vector_swi handler
in order to retrieve its immediate field. Since this fault is not
currently dealt with by our exception tables, this results in a panic:
Unable to handle kernel paging request at virtual address 4020841c
pgd = c490c000
[4020841c] *pgd=84451831, *pte=bf05859d, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in: hid_sony(O)
CPU: 1 Tainted: G W O (3.4.0-perf-gf496dca-01162-gcbcc62b #1)
PC is at vector_swi+0x28/0x88
LR is at 0x40208420
This patch wraps all of the swi instruction loads with the USER macro
and provides a shared exception table entry which simply rewinds the
saved user PC and returns from the system call (without setting tbl, so
there's no worries with tracing or syscall restarting). Returning to
userspace will re-enter the page fault handler, from where we will
probably send SIGSEGV to the current task.
Reported-by: Wang, Yalin <yalin.wang@sonymobile.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the missing VPU devicetree node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The gpio-ranges properties in vf610.dtsi were written according to an
older version of the GPIO bindings. Unfortunately, these were changed
incompatibly in commit 86853c8 "gpio: add gpio offset in gpio range
cells property". This patch adds the missing required extra cell in each
gpio-ranges property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On Sabre SD, system controls WM8962 power by pulling up/down GPIO_4_10,
so add a regulator controled by GPIO_4_10 for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Setting GPIO_0 pad as clko1 clock output to provide MCLK for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds name for NOR flash. This keeps compatibility for
commandline partitions parsing from old bootloaders and make name
of device same for DT and non-DT boot.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the WEIM NOR for imx6q{dl}-sabreauto boards.
For the pin conflict with SPI NOR, its status is set to "disabled".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the clock and compatible information for the weim.
Also adds the weim label.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.
In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.
The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[Steffen: split up patch into tqma53+mba53 part]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add properties to make use of pca9554 gpio expander.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the sgtl5000 found on MBa53 mainboard.
Also enable audio muxer and ssi, which are needed for sound to work.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As the displays are optional and we have more than one, also
set the status of the parallel display and the ldb to disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds the Television Encoder (TVEv2) device tree node
to the i.MX53 dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
UART1 and UART2 can be unused on some designs with PCM038 module.
Remove these definitions from basic dts and lets choose user only
necessary UARTs in custom designs.
Keep UART0 for using this one as boot console, but since we have
not way to disable usage RTSCTS signals, remove this parameter for UART0.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
FEC (KSZ8001L) reset pin is connected to GPIOC30.
Add this definition to dts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a group to the fec pinctrl, for use with MII interface.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Configure the data and tag latency for the L2 cache. This improves the
system performance.
This configuration is taken from Freescale's kernel patch
"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]
which does
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_TAG_LATENCY_CTRL));
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_DATA_LATENCY_CTRL));
In this patch we are doing the same via the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1
Since the SPI/NOR has pin conflict with the WEIM NOR,
we disable the spi/nor by default.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The gpmi does not use the MX6Q_PAD_NANDF_CS2__NAND_CE2_B and
MX6Q_PAD_NANDF_CS3__NAND_CE3_B.
Just remove them.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds support for the Ka-Ro TX53 System-On-Module.
As a baseboard is needed to operate it, only a *.dtsi and no Makefile entry.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for the DENX M53EVK board. The board currently supports
NAND, Ethernet, UART, CAN, I2C.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With device tree clk lookup support in place, we can move audio codec
clk lookup for ssi_ext1 into device tree now, so that imx53_qsb_init()
can be saved.
Since ssi_ext2 lookup is used nowhere, it gets removed together with
ssi_ext1 lookup from clk driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for NAND on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of I2C2 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of I2C1 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of CAN1 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for the AUDMUX4 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c character devices correctly,
so that /dev/i2c-0 corresponds to i2c1, /dev/i2c-1 corresponds
to i2c2, and so on. Currently they are ordered by register
address.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
WM8962 needs 24MHz clock for its MCLK, so choose PLL4 as the parent of clko1.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
These options are useful for controlling backlight contrast via PWM.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There are ulpi access ops implemented in drivers/usb/phy/phy-ulpi.c.
mxc access ops implement the same access operations within mach-imx. This
patch removes the mxc ulpi file and uses phy-ulpi instead for
imx_otg_ulpi_create.
phy-ulpi successfully tested with i.MX27 Phytec phyCARD-S (pca100).
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
commit 84344b43c (ARM: i.MX5: Allow DT clock providers) introduce the following
sparse warning:
arch/arm/mach-imx/clk.c:12:43: warning: Using plain integer as NULL pointer
There is no need to initialize phandle, so remove it.
Cc: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix the following sparse warning:
arch/arm/mach-imx/irq-common.c:24:5: warning: symbol 'mxc_set_irq_fiq' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of explicitly calling clock initialization functions, we can
declare the functions with CLK_OF_DECLARE() and then call common
of_clk_init() to have them invoked properly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Let the mx53 TVE driver be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CCM_CBCMR register (address 0x02C4018) has different meaning
between the i.MX6 Quad/Dual and the i.MX6 Solo/DualLite.
Compared to the i.MX6 Quad/Dual, the CCM_CBCMR register in the
i.MX6 Solo/DualLite reuses the gpu2d_core bits for the MLB clock
configuration.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds the S/PDIF clocks for i.MX51 and i.MX53. Tested on i.MX53.
The i.MX51 has a second set of spdif_root clock dividers, and on i.MX53
there is an additional input to the spdif_xtal mux.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MLB PLL should be handled internally in MLB driver,
so remove it from pllv3.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MLB PLL clock's operation doesn't fit for clock framework and
it should be handled internally in MLB driver.
Remove initialization of pll8_mlb clock device but leave its
declaration in mx6q_clks to avoid affecting imx6q clock numbering.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add clock support for i.MX6 SoloLite. It uses the dtc marco support to
define all clock IDs in imx6sl-clock.h, which will be included by both
clock driver and device tree sources, so that the data will stay sync
all the time between kernel and DT.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The mxc_arch_reset_init() uses static mapping and calls clk_get_sys() to
get clock. It's suitable for non-DT boot but not for DT boot where
dynamic mapping and of_clk_get() should be used instead. Create
mxc_arch_reset_init_dt() as the DT variant of mxc_arch_reset_init(),
and change DT platforms to use it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's inappropriate to call clk_prepare() in mxc_restart(), because the
restart routine could be called in atomic context. Move clk_get() and
clk_prepare() into mxc_arch_reset_init() and only have the atomic part
clk_enable() be called in mxc_restart().
As a result, mxc_arch_reset_init() needs to be called after clk gets
initialized.
While there, it also changes printk(KERN_ERR ...) to pr_err() and adds
__init annotation for mxc_arch_reset_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Matt Porter