The i40evf_reset_task function is a couple hundred lines and it has
a separable block that disables VF. Move that block to a new
i40evf_disable_vf function to shorten i40evf_reset_task a bit.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add logical_id to I40E_AQ_CAP_ID_MNG_MODE capability starting from major
version 2.
Change-ID: Idb29214b172ea5c70cbd45a99e6745c0215af7e4
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A comment incorrectly referred to i40e_vsi_sync_filters_subtask which
does not actually exist. Reference the correct function instead.
Change-ID: I6bd805c605741ffb6fe34377259bb0d597edfafd
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some external PHYs require Clause22 method for accessing registers.
This patch also adds some defines to support blink led on devices using
10CBaseT PHY.
Change-ID: I868a4326911900f6c89e7e522fda4968b0825f14
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Separate the global private flags and the regular private flags per
interface into two arrays. Future additions of private flags will not
need to be duplicated which may lead to buggy code. Also rename
"i40e_priv_flags_strings_gl" to "i40e_gl_priv_flags_strings" for
clarity, as it reads more naturally.
Change-ID: I68caef3c9954eb7da342d7f9d20f2873186f2758
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace a check of magic number 4095 with VLAN_N_VID. This
makes it obvious that a later check against VLAN_N_VID is
always true and can be removed.
Change-ID: I28998f127a61a529480ce63d8a07e266f6c63b7b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This label is unnecessary, as are jumping to a block that checks aq_ret
and then immediately skipping it and returning. So just jump straight to
the error_param and remove this unnecessary label.
Also use goto error_param even in the last check for style consistency.
Change-ID: If487c7d10c4048e37c594e5eca167693aaed45f6
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we are much more robust about defining what we
can and cannot offload. Previously we were performing no checks. This
should bring us up to parity with the i40e PF driver.
In addition the device only supports GSO as long as the MSS is 64 or
greater. We were not checking this so an MSS less than that was resulting
in Tx hangs.
Change-ID: If533553ec92fc6ba694eab6ac81fdaf3004f3592
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we are much more robust about defining what we
can and cannot offload. Previously we were just checking for the L4 tunnel
header length, however there are other fields we should be verifying as
there are multiple scenarios in which we cannot perform hardware offloads.
In addition the device only supports GSO as long as the MSS is 64 or
greater. We were not checking this so an MSS less than that was resulting
in Tx hangs.
Change-ID: I5e2fd5f3075c73601b4b36327b771c64fcb6c31b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
geneve{,6}_build_skb can end up doing a pskb_expand_head(), which
makes the ip_hdr(skb) reference we stashed earlier stale. Since it's
only needed as an argument to ip_tunnel_ecn_encap(), move this
directly in the function call.
Fixes: 08399efc63 ("geneve: ensure ECN info is handled properly in all tx/rx paths")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhAkJ0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklarJlCACp3d7A2H/xNs+9mz0KNW/r1Dn+gwjh
ZMvcHEs0FvYjzdpgstd7I7My1iNGbNsjm4MNwyfsGoLAEivPl+tmDcvVR+rpBJRE
k5jtHUGAwkKEUubVT199Oj4YY5YVUTi7YmqedArXMdHP4kRx+efhrjtmjI2CoL/j
XS2W0YA8MmaKgyTS/UTElZ8/SlX6o1ZJp5JrEFUexyURw7qlTThKJ+jDdhrL7pUx
zxamj3umv6F5N21ZIGZTBIMEzVOSfU3nPZGC5M/K4rNNznM/X7sYM8ALjY/bSPNU
zykf/Ut5BcLaLXm/tyNZvNfv7Y8LCCImO05U8BY9yDDgigmgF62YhT8w
=iiHQ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-02
this is a pull request for net/master.
There are two patches by Stephane Grosjean, who adds support for the new
PCAN-USB X6 USB interface to the pcan_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to set the other "err" variable here so that we can return it
later. My version of GCC misses this issue but I caught it with a
static checker.
Fixes: 9f70eb339f ("net: ethernet: renesas: ravb: fix fixed-link phydev leaks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When streaming a lot of data and the RZ/A1 can't keep up, some status bits
will get set that are not being checked or cleared which cause the
following messages and the Ethernet driver to stop working. This
patch fixes that issue.
irq 21: nobody cared (try booting with the "irqpoll" option)
handlers:
[<c036b71c>] sh_eth_interrupt
Disabling IRQ #21
Fixes: db893473d3 ("sh_eth: Add support for r7s72100")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__bcmgenet_tx_reclaim() and bcmgenet_free_rx_buffers() are not using the
same struct device during unmap that was used for the map operation,
which makes DMA-API debugging warn about it. Fix this by always using
&priv->pdev->dev throughout the driver, using an identical device
reference for all map/unmap calls.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada 3700 is a new ARMv8 SoC from Marvell using same network controller
as older Armada 370/38x/XP. There are however some differences that
needed taking into account when adding support for it:
* open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus
configuration for network controller has to be done on two levels:
global and per-port. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed
* make per-CPU operation optional - Recent patches adding RSS and XPS
support for Armada 38x/XP enabled per-CPU operation of the controller
by default. Contrary to older SoC's Armada 3700 SoC's network
controller is not capable of per-CPU processing due to interrupt lines'
connectivity. This patch restores non-per-CPU operation, which is now
optional and depends on neta_armada3700 flag value in mvneta_port
structure. In order not to complicate the code, separate interrupt
subroutine is implemented.
For now, on the Armada 3700, RSS is disabled as the current
implementation depend on the per cpu interrupts.
[gregory.clement@free-electrons.com: extract from a larger patch, replace
some ifdef and port to net-next for v4.10]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually only the mvneta_bm support is not 64-bits compatible.
The mvneta code itself can run on 64-bits architecture.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the mvneta driver in order to be usable on the 64 bits platform
such as the Armada 3700.
[gregory.clement@free-electrons.com]: this patch was extract from a larger
one to ease review and maintenance.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the virtual address of the received buffer were stored in the
cookie field of the rx descriptor. However, this field is 32-bits only
which prevents to use the driver on a 64-bits architecture.
With this patch the virtual address is stored in an array not shared with
the hardware (no more need to use the DMA API). Thanks to this, it is
possible to use cache contrary to the access of the rx descriptor member.
The change is done in the swbm path only because the hwbm uses the cookie
field, this also means that currently the hwbm is not usable in 64-bits.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HWBM all buffers are allocated in mvneta_bm_construct() and in runtime
they are put into descriptors by hardware. There is no need to fill them
at this point.
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For small frame reuse the phys_addr variable instead of accessing the
uncacheable value in the rx descriptor.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PID 0x1040 of Telit LE922A.
The qmi adapter requires to have DTR set for proper working,
so QMI_WWAN_QUIRK_DTR has been enabled.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduced a work-around in usbnet_cdc_status() for devices that exported
cdc carrier on twice on connect. Before the commit, this behavior caused
the link state to be incorrect. It was assumed that all CDC Ethernet
devices would either export this behavior, or send one off and then one on
notification (which seems to be the default behavior).
Unfortunately, it turns out multiple devices sends a connection
notification multiple times per second (via an interrupt), even when
connection state does not change. This has been observed with several
different USB LAN dongles (at least), for example 13b1:0041 (Linksys).
After bfe9b9d2df, the link state has been set as down and then up for
each notification. This has caused a flood of Netlink NEWLINK messages and
syslog to be flooded with messages similar to:
cdc_ether 2-1:2.0 eth1: kevent 12 may have been dropped
This commit fixes the behavior by reverting usbnet_cdc_status() to how it
was before bfe9b9d2df. The work-around has been moved to a separate
status-function which is only called when a known, affect device is
detected.
v1->v2:
* Do not open-code netif_carrier_ok() (thanks Henning Schild).
* Call netif_carrier_off() instead of usb_link_change(). This prevents
calling schedule_work() twice without giving the work queue a chance to be
processed (thanks Bjørn Mork).
Fixes: bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent commit to get more precise rx/tx counters in ndo_get_stats64()
can lead to crashes at device dismantle, as Jesper found out.
We must prevent mlx4_en_fold_software_stats() trying to access
tx/rx rings if they are deleted.
Fix this by adding a test against priv->port_up in
mlx4_en_fold_software_stats()
Calling mlx4_en_fold_software_stats() from mlx4_en_stop_port()
allows us to eventually broadcast the latest/current counters to
rtnetlink monitors.
Fixes: 40931b8511 ("mlx4: give precise rx/tx bytes/packets counters")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-and-bisected-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@dev.mellanox.co.il>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit queue timeout issue is seen in two cases
- Due to a race condition btw setting stop_queue at xmit()
and checking for stopped_queue in NAPI poll routine, at times
transmission from a SQ comes to a halt. This is fixed
by using barriers and also added a check for SQ free descriptors,
incase SQ is stopped and there are only CQE_RX i.e no CQE_TX.
- Contrary to an assumption, a HW errata where HW doesn't stop transmission
even though there are not enough CQEs available for a CQE_TX is
not fixed in T88 pass 2.x. This results in a Qset error with
'CQ_WR_FULL' stalling transmission. This is fixed by adjusting
RXQ's RED levels for CQ level such that there is always enough
space left for CQE_TXs.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ndo_setup_tc is called with an egress_dev flag set, it means that
the ndo call was executed on the mirred action (egress) device and not
on the ingress device.
In order to support this kind of ndo_setup_tc call, and insert the
correct decap rule to the hardware, the uplink device on the same eswitch
should be found.
Currently, we use this resolution between the mirred device and the
uplink on the same eswitch to offload vxlan shared device decap rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the representor private data to a net_device pointer holding the
representor netdevice, instead of void pointer holding mlx5e_priv.
It will be used by a new eswitch service function, returning the uplink representor
netdevice.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF Representor udp tunnel ndo entries were removed by mistake,
return them.
Fixes: 370bad0f9a ('net/mlx5e: Support HW (offloaded) and SW counters for SRIOV switchdev mode')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds out of order packet handling for hardware offloaded
iSCSI. Out of order packet handling requires driver buffer allocation
and assistance.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the iSCSI driver (qedi) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver already uses its private lock for synchronization between xmit
and xmit completion handler making the additional use of the xmit_lock
unnecessary.
Furthermore the driver does not set NETIF_F_LLTX resulting in xmit to be
called with the xmit_lock held and then taking the private lock while xmit
completion handler does the reverse, first take the private lock, then the
xmit_lock.
Fix these issues by not taking the xmit_lock in the tx completion handler.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
An explicit dma sync for device directly after mapping as well as an
explicit dma sync for cpu directly before unmapping is unnecessary and
costly on the hotpath. So remove these calls.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is already using the %pM printf extension; might as well also use
%ph to make the code smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_INET is disabled, the new selftest results in a link
error:
drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.o: In function `mlx5e_test_loopback':
en_selftest.c:(.text.mlx5e_test_loopback+0x2ec): undefined reference to `ip_send_check'
en_selftest.c:(.text.mlx5e_test_loopback+0x34c): undefined reference to `udp4_hwcsum'
This hides the specific test in that configuration.
Fixes: 0952da791c ("net/mlx5e: Add support for loopback selftest")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 326fe02d1e ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock"),
the rcu_read_lock() in bpf_prog_run_xdp() is superfluous, since callers
need to hold rcu_read_lock() already to make sure BPF program doesn't
get released in the background.
Thus, drop it from bpf_prog_run_xdp(), as it can otherwise be misleading.
Still keeping the bpf_prog_run_xdp() is useful as it allows for grepping
in XDP supported drivers and to keep the typecheck on the context intact.
For mlx4, this means we don't have a double rcu_read_lock() anymore. nfp can
just make use of bpf_prog_run_xdp(), too. For qede, just move rcu_read_lock()
out of the helper. When the driver gets atomic replace support, this will
move to call-sites eventually.
mlx5 needs actual fixing as it has the same issue as described already in
326fe02d1e ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock"),
that is, we're under RCU bh at this time, BPF programs are released via
call_rcu(), and call_rcu() != call_rcu_bh(), so we need to properly mark
read side as programs can get xchg()'ed in mlx5e_xdp_set() without queue
reset.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling flow encap entry should be inside tc del flow
and is only relevant for offloaded eswitch TC rules.
Fixes: 11a457e9b6c1 ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the function that deletes offloaded TC rule to get
struct mlx5e_tc_flow instance which contains both the flow
handle and flow attributes. This is a cleanup needed for
downstream patches, it doesn't change any functionality.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the reverse unwinding principle, on delete time we should
first handle deletion of the steering rule and later handle the vlan
deletion from the eswitch.
Fixes: 8b32580df1 ("net/mlx5e: Add TC vlan action for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will never find a flow with the same cookie as cls_flower always
allocates a new flow and the cookie is the allocated memory address.
Fixes: e3a2b7ed01 ("net/mlx5e: Support offload cls_flower with drop action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Striding RQ implementation, we used a single UMR
(User-Mode Memory Registration) memory key for all RQs.
When the product of RQs number*size gets high, we hit a
limitation of u16 field size in FW.
Here we move to using a UMR memory key per RQ, so we can
scale to any number of rings, with the maximum buffer
size in each.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In next patch we are going to create a UMR MKey per RQ, we need
mlx5e_create_umr_mkey declared before mlx5e_create_rq.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new type of struct mlx5_frag_buf which is used to allocate fragmented
buffers rather than contiguous, and make the Completion Queues (CQs) use
it as they are big (default of 2MB per CQ in Striding RQ).
This fixes the failures of type:
"mlx5e_open_locked: mlx5e_open_channels failed, -12"
due to dma_zalloc_coherent insufficient contiguous coherent memory to
satisfy the driver's request when the user tries to setup more or larger
rings.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by adding a new glue helper
function.
Drop the of-node reference taken in the same path also on late probe
errors (and not just on driver unbind) by moving the put from
stmmac_dvr_remove() to the new helper.
Fixes: 277323814e ("stmmac: add fixed-link device-tree support")
Fixes: 4613b279be ("ethernet: stmicro: stmmac: add missing of_node_put
after calling of_parse_phandle")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the OF-helper function header to reflect that the function no longer
has a platform-data parameter.
Fixes: b0003ead75 ("stmmac: make stmmac_probe_config_dt return the
platform data struct")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable clocks before returning on late probe errors.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic
Meson 8b / GXBB DWMAC")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to call any exit() callback to undo the effect of init()
before returning on late probe errors.
Fixes: cf3f047b9a ("stmmac: move hw init in the probe (v2)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable runtime PM, power down the PHY, and disable clocks
before returning on late probe errors.
Fixes: 27ffefd2d1 ("stmmac: dwmac-rk: create a new probe function")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable clocks before returning on late probe errors.
Fixes: 8387ee21f9 ("stmmac: dwmac-sti: turn setup callback into a
probe function")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to call stmmac_dvr_remove() before returning on late probe
errors so that memory is freed, clocks are disabled, and the netdev is
deregistered before its resources go away.
Fixes: 3c201b5a84 ("net: stmmac: socfpga: Remove re-registration of
reset controller")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the (optional) SGMII PCS functionality of the Altera
TSE MAC. If the phy-mode is set to 'sgmii' then we attempt to discover
and initialise the PCS so that the MAC can communicate to the PHY.
The PCS IP block provides a scratch register for testing presence of
the PCS, which is mapped into one of the two MDIO spaces present in
the MAC's register space. Once we have determined that the scratch
register is functioning, we attempt to initialise the PCS to
auto-negotiate an SGMII link with the PHY. There is no need to monitor
or manage the SGMII link beyond this, since the normal PHY MDIO will
then be used to monitor the media layer.
The Altera TSE MAC has only one way in which it can be configured with an
SGMII PCS, and as such, this patch only looks to the phy-mode to select
whether or not to attempt to initialise the PCS registers. During
initialisation, we report the PCS's equivalent of a PHY ID register.
This can be parameterised during the IP instantiation and is often left
as '0x00000000' which is not an error.
Signed-off-by: Neill Whillans <neill.whillans@codethink.co.uk>
Reviewed-by: Daniel Silverstone <daniel.silverstone@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Vitesse VSC8572 which is functionally equivalent to
the already supported VSC8574. As such, all the same handling functions
are used since the VSC8572 merely has half the number of phy blocks
internally.
Signed-off-by: Stephen Agate <stephen.agate@uk.thalesgroup.com>
Signed-off-by: Neill Whillans <neill.whillans@codethink.co.uk>
Reviewed-by: Daniel Silverstone <daniel.silverstone@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.
In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.
In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.
Fixes: e10715d3e9 ("igb/igbvf: Add support for GSO partial")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's no longer used now that Falcon is gone.
Also remove a reference in a comment to an ioctl that doesn't exist.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Easy enough for Falcon users to enable it when making oldconfig.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defalconisation removed one of the string arguments, but missed the
corresponding %s.
Fixes: 5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes AX88772_suspend() USB vendor commands failure issues.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers to have an eth_tp_mdix_ctrl to indicate what is the configured
MDI setting, and read eth_tp_mdi to indicate what is the current status,
Add new parameter mdix_ctrl in phy_device structure and fix driver.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To connect two ports of the same configuration (MDI to MDI or
MDI-X to MDI-X) with a 10/100/1000 Mbit/s connection, an
Ethernet crossover cable is needed to cross over the transmit
and receive signals in the cable, so that they are matched at
the connector level.
When connecting an MDI port to an MDI-X port a straight through
cable is used while to connect two MDI ports or two MDI-X ports
a crossover cable must be used. Conventionally MDI is used on end
devices while MDI-X is used on hubs and switches
Auto MDI-X automatically detects the required cable connection
type and configures the connection appropriately, removing the
need for crossover cables to interconnect switches or connecting
PCs peer-to-peer.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the mdix and mdix_ctrl with corresponding ethtool configuration
parameters.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake "oustanding" to "outstanding" in
comment and dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for PEAK-System PCAN-USB X6 USB to CAN interface.
The CAN FD adapter PCAN-USB X6 allows the connection of up to 6 CAN FD
or CAN networks to a computer via USB. The interface is installed in an
aluminum profile casing and is shipped in versions with D-Sub connectors
or M12 circular connectors.
The PCAN-USB X6 registers in the USB sub-system as if 3x PCAN-USB-Pro FD
adapters were plugged. So, this patch:
- updates the PEAK_USB entry of the corresponding Kconfig file
- defines and adds the device id. of the PCAN-USB X6 (0x0014) into the
table of supported device ids
- defines and adds the new software structure implementing the PCAN-USB X6,
which is obviously a clone of the software structure implementing the
PCAN-USB Pro FD.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This fixes the bitimings fields ranges supported by all the CAN-FD USB
interfaces of the PEAK-System CAN-FD adapters.
Very first development versions of the IP core API defined smaller TSGEx
and SJW fields for both nominal and data bittimings records than the
production versions. This patch fixes them by enlarging their sizes to
the actual values:
field: old size: fixed size:
nominal TSGEG1 6 8
nominal TSGEG2 4 7
nominal SJW 4 7
data TSGEG1 4 5
data TSGEG2 3 4
data SJW 2 4
Note that this has no other consequences than offering larger choice to
bitrate encoding.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ath.git patches for 4.10. Major changes:
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
The H2C MEDIA_STATUS_RPT command for some reason causes 8192eu and
8723bu devices not being able to reconnect.
Reported-by: Barry Day <briselec@gmail.com>
Cc: <stable@vger.kernel.org> #4.8+
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop duplicate header vmalloc.h from ath5k/debug.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added new areas to fw_mappings area for UCODE code
and data areas.
The new areas are only exposed through debugfs blobs,
and mainly needed to access UCODE logs.
The change does not affect crash dumps because the
newly added areas overlap with the "upper" area which
is already dumped.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
num_descriptors and descriptor_size needs to be
checked for:
1) not being negative values
2) no overflow occurs when these are multiplied
together as done in wil_pmc_read.
An overflow of two signed integers is undefined
behavior.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The usb_*_msg() functions expect a timeout in msecs but are given HZ,
which is ticks per second. If HZ=100, firmware download often times out
when there is modest USB utilization and the device fails to initialize.
Replaces HZ in usb_*_msg timeouts with 1000 msec since HZ is one second
for timeouts in jiffies.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare the structure ath_bus_ops as const as it is only passed as an
argument to the function ath9k_init_device. This argument is of type
const struct ath_bus_ops *, so ath_bus_ops structures with this property
can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ath_bus_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
expression e1,e2;
@@
ath9k_init_device(e1,e2,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ath_bus_ops i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ath_bus_ops i;
File size before:
text data bss dec hex filename
1295 232 0 1527 5f7 ath/ath9k/ahb.o
File size after:
text data bss dec hex filename
1359 176 0 1535 5ff ath/ath9k/ahb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.
This seems to fix errors like this on my x86-64 machine:
kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
DMAR:[fault reason 05] PTE Write access is not set
Tested-by: Marek Behun <kabel@blackhole.sk>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'
a) memory footprint of ath10k without the change
lsmod | grep ath10k
ath10k_core 414498 1 ath10k_pci
ath10k_pci 38236 0
b) memory footprint of ath10k with the change
ath10k_core 414980 1 ath10k_pci
ath10k_pci 38236 0
Memory Failure Call trace:
hostapd: page allocation failure: order:6, mode:0xd0
[<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.
The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Radar pulse and spectral scan reports are provided by the HW
with the ATH9K_RXERR_PHY flag set. Those are forwarded to
the dfs-detector and spectral module for further processing.
For some older chips, the pre-conditions checked in those
modules are ambiguous, since ATH9K_PHYERR_RADAR is used to
tag both types. As a result, spectral frames are fed into
the dfs-detector and vice versa.
This could lead to a false radar detection on a non-DFS
channel (which is uncritical), but more relevant it causes
useless CPU load for processing invalid frames.
This commit ensures that the dfs-detector and spectral
collector are only fed when they are active.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We trigger uarg->callback() immediately after we decide do datacopy
even if caller want to do zerocopy. This will cause the callback
(vhost_net_zerocopy_callback) decrease the refcount. But when we meet
an error afterwards, the error handling in vhost handle_tx() will try
to decrease it again. This is wrong and fix this by delay the
uarg->callback() until we're sure there's no errors.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We trigger uarg->callback() immediately after we decide do datacopy
even if caller want to do zerocopy. This will cause the callback
(vhost_net_zerocopy_callback) decrease the refcount. But when we meet
an error afterwards, the error handling in vhost handle_tx() will try
to decrease it again. This is wrong and fix this by delay the
uarg->callback() until we're sure there's no errors.
Reported-by: wangyunjian <wangyunjian@huawei.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mtu_adj is initialized to zero when alloc mem, there is no any
assignment to mtu_adj. It is only used in ipvlan_adjust_mtu as one
right value.
So it is useless member of struct ipvl_dev, then remove it.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_set_real_num_tx/rx_queues() are required to be called with rtnl_lock
taken, otherwise ASSERT_RTNL() warning will be triggered - which happens
now during System resume from suspend:
cpsw_resume()
|- cpsw_ndo_open()
|- netif_set_real_num_tx/rx_queues()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_open() by rtnl_lock/unlock() calls.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: commit e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In alloc_cmd_box(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx4_alloc_cmd_mailbox(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split device budget between channels according to channel rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check budget fullness only after it's updated and update
channel mask only once to keep budget balance between channels.
It's also needed for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpdma has 8 rate limited tx channels. This patch adds
ability for cpdma driver to use 8 tx h/w shapers. If at least one
channel is not rate limited then it must have higher number, this
is because the rate limited channels have to have higher priority
then not rate limited channels. The channel priority is set in low-hi
direction already, so that when a new channel is added with ethtool
and it doesn't have rate yet, it cannot affect on rate limited
channels. It can be useful for TSN streams and just in cases when
h/w rate limited channels are needed.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The weight of a channel is needed to split descriptors between
channels. The weight can depend on maximum rate of channels, maximum
rate of an interface or other reasons. The channel weight is in
percentage and is independent for rx and tx channels.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mwifiex
* properly terminate SSIDs so that uninitalised memory is not printed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYPZM9AAoJEG4XJFUm622bnTwH/j7KbWbTLE2H9abYJxne3sWQ
FOCrGNICgG9HYyLn33k7+dCBHGYa1f5qWO7dIeWhe6LEtXqrWBsxUFZbMrJVU7Te
sDr3s2364iIPhdLtYl5mM7M75Y2h2pt1XhpErmldCpFpnYad5vZEbIR1n96F3cz6
0ft6iUJpd3bf+KWxDUc707Vln42optvbcp7gjF+6mdShb0jlFkV9eOa85aJH6v38
5kKPhLfiv1Qs1sZXPrWc2oQUIc0LDY19sXtw/5DTLe4+r6ybsKlF1o4+b2yOVeiu
nrm1F/2D/829w3+4iYE63wACPGvyVaKYROtYgquyYkrI+6xyh1fmnout6SiwLe8=
=oEuI
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
mwifiex
* properly terminate SSIDs so that uninitalised memory is not printed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for forwarding via XDP. Once the eBPF is attached,
driver would allocate & configure a designated transmission queue
meant solely for forwarding packets. Said queue would share the
receive-queue's interrupt line, and would have it's own Tx statistics.
Infrastructure changes required for this [spread-out through the code]:
- Determine the DMA direction of the receive buffers based on the presence
of the eBPF program.
- Turn the sw Tx ring into a union, as regular/XDP queues have different
needs for releasing resources after completion [regular requires the SKB,
XDP requires the transmitted page].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ndo_xdp callback. This patch would support XDP_PASS,
XDP_DROP and XDP_ABORTED commands.
This also adds a per Rx queue statistic which counts number of packets
which didn't reach the stack [due to XDP].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the cacheline usage of both queues by reordering -
This reduces the cachelines required for egress datapath processing
from 3 to 2 and those required by ingress datapath processing by 2.
It also changes a couple of datapath related functions that currently
require either the fastpath or the qede_dev, changing them to be based
on the tx/rx queue instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive-hashing is a fixed feature, so there's no need to check
during the ingress datapath whether it's set or not.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.
This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.
This patch re-organizes the way L2 queues are configured and maintained.
In short:
- Required parameters for queue init are now well-defined.
- Qed would allocate a queue-cid based on parameters.
Upon initialization success, it would return a handle to caller.
- Queue-handle would be maintained by entity requesting queue-init,
not necessarily qed.
- All further queue-APIs [update, destroy] would use the opaque
handle as reference for the queue instead of various indices.
The possible owners of such handles:
- PF queues [qede] - complete handles based on provided configuration.
- VF queues [qede] - fw-context-less handles, containing only relative
information; Only the PF-side would need the absolute indices
for configuration, so they're omitted here.
- VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As qede utilizes an internal-reload sequence as result of various
configuration changes, the netif state wouldn't always accurately describe
the status of the configuration.
To compensate, we're storing an internal state of the device, which should
only be accessed under the qede_lock.
This patch fixes and improves several state/lock interactions:
- The internal state should only be checked while locked.
- While holding lock, it's preferable to check state rather than
the netdevice's state.
- The reload sequence is not 'atomic' - unload and subsequent load
are not in the same critical section.
This also add the 'locked' variant for the reload, which would later be
used by XDP - useful in the case where the correct sequence is 'lock,
check state and re-configure if good', instead of allowing the reload
itself to make the decision regarding the configurability of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver's NAPI poll is using a long sequence for processing ingress
packets, and it's going to get even longer once we do XDP.
Break down the main loop into a series of sub-functions to allow
better readability of the function.
While we're at it, correct the accounting of the NAPI budget -
currently we're counting only packets passed to the stack against
the budget, even in case those are actually aggregations.
After refactoring every CQE processed would be counted against the budget.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor logic for gathering statistics into a per-queue function.
This improves readability of the driver statistics' flows.
In addition, this would be required by the XDP forwarding queues
[as we'll need the Txq statistics gathering methods for those as well].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently doesn't support multi-CoS, but it contains logic
where multiple transmission queues could be theoretically manipulated.
No point in maintaining the infrastructure at the moment.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chain structure and functions are widely used by the qed* modules,
both for configuration and datapath.
E.g., qede's Tx has one such chain and its Rx has two.
Currently, the strucutre's fields which are required for datapath
related functions [produce/consume] are intertwined with fields which
are required only for configuration purposes [init/destroy/etc.].
This patch re-arranges the chain structure so that all the fields which
are required for datapath usage could reside in a single cacheline instead
of the two which are required today.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver needs to maintain a structure per-each concurrent possible
open aggregation, but the structure storing that metadata is far from
being optimized - biggest waste in it is that there are 2 buffer metadata,
one for a replacement buffer when the aggregation begins and the other for
holding the first aggregation's buffer after it begins [as firmware might
still update it]. Those 2 can safely be united into a single metadata
structure.
struct qede_agg_info changes the following:
/* size: 120, cachelines: 2, members: 9 */
/* sum members: 114, holes: 1, sum holes: 4 */
/* padding: 2 */
/* paddings: 2, sum paddings: 8 */
/* last cacheline: 56 bytes */
-->
/* size: 48, cachelines: 1, members: 9 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 48 bytes */
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for netdev private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero the stats portion of it
again in the driver's probe function.
In any case, the size for the memset is wrong as the stats member is of
type rtnl_link_stats64, not net_device_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Execution 'ethtool -S' on fec device that is down causes OOPS on Vybrid
board:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0898200
pgd = ddecc000
[e0898200] *pgd=9e406811, *pte=400d1653, *ppte=400d1453
Internal error: : 1008 [#1] SMP ARM
...
Reason of OOPS is that fec_enet_get_ethtool_stats() accesses fec
registers while IPG clock is stopped by PM.
Fix that by caching statistics in fec_enet_private. Cache is initialized
at device probe time, and updated at statistics request time if device
is up, and also just before turning device off on down path.
Additional locking is not needed, since cached statistics is accessed
either before device is registered, or under rtnl_lock().
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces printk() with netdev_err() for macvtap device.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_fdb_append may return error, so add the proper check,
otherwise it will cause memory leak.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Changes in v2:
- Unnecessary to initialize rc to zero.
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF initialization and destroy resources.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF interrupt processing.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF mailbox setup.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for initializing softcommand, dispatch and
instructions queues for VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VF device register access.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for configuring VF input/output queues.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for setting up VF configuration.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for cn23xx VF probe and registration.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for CN23xx VF registers.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Rasesh Mody <Rasesh.Mody@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom BCM7xxx internal PHYs can leverage the Broadcom PHY library
module PHY error counters helper functions, just implement the
appropriate PHY driver function calls to do so. We need to allocate some
storage space for our PHY statistics, and provide it to the Broadcom PHY
library, so do this in a specific probe function, and slightly wrap the
get_stats function call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool's '-r' command. Restarting
N-WAY negotiation can be useful to activate newly changed EEE
settings etc.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to query and set Energy Efficient Ethernet parameters
via ethtool for applicable devices.
This patch doesn't activate full EEE support in cpsw driver, but it
enables reading and writing EEE advertising settings. This way one
can disable advertising EEE for certain speeds.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using fakelb with different network sizes it becomes handy to have the
number of created fake devices printed in the log as well.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
This patch changes the rssi base value to -94 for at86rf33 transceivers.
The code before assumes a rssi base value of -91 which is for the
at86rf231 transceiver only. This change need to update the cca ed
threshold mapping table.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Also remember to put the of-node reference on probe errors.
Fixes: 1bb6aa56bb ("net: davinci_emac: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 077742dac2 ("dwc_eth_qos: Add support for Synopsys DWC Ethernet
QoS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on initialisation errors and on device
close after having disconnected the PHY.
Fixes: b4bc88a868 ("ravb: Add fixed-link support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on initialisation errors and on uninit.
Fixes: 0c72c50f6f ("net-next: mediatek: add fixed-phy support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 83895bedee ("net: mvneta: add support for fixed links")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: bb74d9a4a8 ("fs_enet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 407066f8f3 ("net: fec: Support phys probed from devicetree and
fixed-link")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Note that we're still leaking any fixed-link PHY registered in the
non-OF probe path.
Fixes: 9abf0c2b71 ("net: bcmgenet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 186534a3f8 ("net: systemport: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: c7dfe3abf4 ("net: ethernet: nb8800: support fixed-link DT
node")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 7cdbc6f74f ("altera tse: add support for fixed-links.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we change MTU or the number of channels on a netvsc device we get the
following logged:
hv_netvsc bf5edba8...: net device safe to remove
hv_netvsc: hv_netvsc channel opened successfully
hv_netvsc bf5edba8...: Send section size: 6144, Section count:2560
hv_netvsc bf5edba8...: Device MAC 00:15:5d:1e:91:12 link state up
This information is useful as debug at most.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call bus->init() before allocating 'lag.mapping'. Change the order of
operations in removal path to reflect that.
This makes the error path of mlxsw_core_bus_device_register() symmetric
with mlxsw_core_bus_device_unregister().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this rollback, the thermal zone is still registered during the
error path, whereas its private data is freed upon the destruction of
the underlying bus device due to the use of devm_kzalloc(). This results
in use after free.
Fix this by calling mlxsw_thermal_fini() from the appropriate place in
the error path.
Fixes: a50c1e3565 ("mlxsw: core: Implement thermal zone")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shared buffer pools are containers whose size is used to calculate
the maximum usage for packets from / to a specific port / {port, PG/TC},
when dynamic threshold is employed.
While it's perfectly fine for the sum of the pools to exceed the maximum
size of the shared buffer, a single pool cannot.
Add a check when the pool size is set and forbid sizes larger than the
maximum size of the shared buffer.
Without the patch:
$ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype
dynamic
// No error is returned
With the patch:
$ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype
dynamic
devlink answers: Invalid argument
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be able to limit the size of shared buffer pools, so query
the maximum size from the device during init.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added switchib driver fails to link if MLXSW_PCI=m:
drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function^Cmlxsw_sib_module_exit':
switchib.c:(.exit.text+0x8): undefined reference to `mlxsw_pci_driver_unregister'
switchib.c:(.exit.text+0x10): undefined reference to `mlxsw_pci_driver_unregister'
drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function `mlxsw_sib_module_init':
switchib.c:(.init.text+0x28): undefined reference to `mlxsw_pci_driver_register'
switchib.c:(.init.text+0x38): undefined reference to `mlxsw_pci_driver_register'
switchib.c:(.init.text+0x48): undefined reference to `mlxsw_pci_driver_unregister'
The other two such sub-drivers have a dependency, so add the same one
here. In theory we could allow this driver if MLXSW_PCI is disabled,
but it's probably not worth it.
Fixes: d1ba526384 ("mlxsw: switchib: Introduce SwitchIB and SwitchIB silicon driver")
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device_release_driver(&phydev->mdio.dev) is called, it releases all
resources belonging to the PHY device. Hence the subsequent call to
phy_led_triggers_unregister() will access already freed memory when
unregistering the LEDs.
Move the call to phy_led_triggers_unregister() before the possible call
to device_release_driver() to fix this.
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a hardware issue happened as described by inline comments, the register
write pattern looks like the following:
<write ~MACB_BIT(RE)>
+ wmb();
<write MACB_BIT(RE)>
There might be a memory barrier between these two write operations, so add wmb
to ensure an flip from 0 to 1 for NCR.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On macb only (not gem), when a RX queue corruption was detected from
macb_rx(), the RX queue was reset: during this process the RX ring
buffer descriptor was initialized by macb_init_rx_ring() but we forgot
to also set bp->rx_tail to 0.
Indeed, when processing the received frames, bp->rx_tail provides the
macb driver with the index in the RX ring buffer of the next buffer to
process. So when the whole ring buffer is reset we must also reset
bp->rx_tail so the driver is synchronized again with the hardware.
Since macb_init_rx_ring() is called from many locations, currently from
macb_rx() and macb_init_rings(), we'd rather add the "bp->rx_tail = 0;"
line inside macb_init_rx_ring() than add the very same line after each
call of this function.
Without this fix, the rx queue is not reset properly to recover from
queue corruption and connection drop may occur.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 9ba723b081 ("net: macb: remove BUG_ON() and reset the queue to handle RX errors")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix comments, add some new, and make debugfs output consistent.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4 IP can synthesized with 1-8 number of tx queues.
On an IP synthesized with DWC_EQOS_NUM_TXQ > 1, all txqueues are disabled
by default. For these IPs, the bitfield TXQEN is R/W.
Always enable tx queue 0. The write will have no effect on IPs synthesized
with DWC_EQOS_NUM_TXQ == 1.
The driver does still not utilize more than one tx queue in the IP.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dependencies on the architectures that support these devices and
add compile test to ensure ongoing code build coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 stats are chaotic because a deferred work queue is responsible
to update them every 250 ms.
Even sampling stats every one second with "sar -n DEV 1" gives
variations like the following :
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:39:22 eth0 146877.00 3265554.00 9467.15 4828168.50
07:39:23 eth0 146587.00 3260329.00 9448.15 4820445.98
07:39:24 eth0 146894.00 3259989.00 9468.55 4819943.26
07:39:25 eth0 110368.00 2454497.00 7113.95 3629012.17 <<>>
07:39:26 eth0 146563.00 3257502.00 9447.25 4816266.23
07:39:27 eth0 145678.00 3258292.00 9389.79 4817414.39
07:39:28 eth0 145268.00 3253171.00 9363.85 4809852.46
07:39:29 eth0 146439.00 3262185.00 9438.97 4823172.48
07:39:30 eth0 146758.00 3264175.00 9459.94 4826124.13
07:39:31 eth0 146843.00 3256903.00 9465.44 4815381.97
Average: eth0 142827.50 3179259.70 9206.30 4700578.16
This patch allows rx/tx bytes/packets counters being folded at the
time we need stats.
We now can fetch stats every 1 ms if we want to check NIC behavior
on a small time window. It is also easier to detect anomalies.
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:42:50 eth0 142915.00 3177696.00 9212.06 4698270.42
07:42:51 eth0 143741.00 3200232.00 9265.15 4731593.02
07:42:52 eth0 142781.00 3171600.00 9202.92 4689260.16
07:42:53 eth0 143835.00 3192932.00 9271.80 4720761.39
07:42:54 eth0 141922.00 3165174.00 9147.64 4679759.21
07:42:55 eth0 142993.00 3207038.00 9216.78 4741653.05
07:42:56 eth0 141394.06 3154335.64 9113.85 4663731.73
07:42:57 eth0 141850.00 3161202.00 9144.48 4673866.07
07:42:58 eth0 143439.00 3180736.00 9246.05 4702755.35
07:42:59 eth0 143501.00 3210992.00 9249.99 4747501.84
Average: eth0 142835.66 3182165.93 9206.98 4704874.08
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5ffbe0a19 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7601u_mac_stop_hw should stop polling the rxq once it remains empty
but instead continues polling after the rxq status stays clear; bringing
down the interface takes about six seconds from this alone.
Speed up path by exiting rxq loop once status repeatedly polls empty.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Reviewed-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The scan results for scheduled scan as retrieved from the device
have changed. A field has been added which is not needed. However,
the appended info is. Luckily they are versioned so check that to
find out the location of the appended data.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can specify the interval for the scheduled scan. This
interval is found in scheduled scan plan. The driver supports only
one plan, which is legacy behaviour.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the .sched_scan_start() callback a condition was checked whether a
normal scan was ongoing. However, there is no need for this check as
it is ok to start the scheduled scan irrespective whether or not a
normal scan is ongoing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can provide list of channels in the schedule scan request.
This was ignored so all channels supported and allowed by the device
were used. This patch configures the device to use the channels as
listed in the request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework .sched_scan_start() callback moving actual configuration of
the device in pno source file.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmf_pno_config() function handles two configurations in
firmware. Split it and have caller sort out what is needed.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For scheduled scan we initiate an escan in firmware to obtain more
info missing from the scheduled scan notification we get from firmware.
For upcoming functionality this is also required so make it a bit
more generic.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the number of parameters as the removed ones can be obtained
through struct brcmf_if parameter.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ssids list in the scheduled scan request were not properly taken
into account when configuring in firmware. The hidden bit was set for
any ssid resulting in active scanning for all. Only set it for ssids
that are in the ssids list.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introducing new source file for pno related functionality. Moving
existing pno functions.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This chip was already supported, but seems a device came up giving
a different chip identifier. So adding that effectively mapping to
the same firmware file as for 43340 chip.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rev6 of pcie host dongle interface protocol, host needs to maximum
supported ring number from dongle shared memory and set up ring buffer
and ring indices offset accordingly.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marvell Wifi PCIe modules don't always behave nicely for PCIe power
management when their firmware hasn't been loaded, particularly after
suspending the PCIe link one or more times. When this happens, we might
end up spinning forever in this status-polling tight loop. Let's make
this less tight by adding a timeout and by sleeping a bit in between
reads, as we do with the other similar loops.
This prevents us from hogging a CPU even in such pathological cases, and
allows the FW initialization to just fail gracefully instead.
I chose the same polling parameters as the earlier loop in this
function, and empirically, I found that this loop never makes it more
than about 12 cycles in a sane FW init sequence. I had no official
information on the actual intended latency for this portion of the
download.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_usb_probe() defines and sets bcd_usb but does not use it,
Compiling with W=1 gives the following warning, fix it.
mwifiex/usb.c: In function ‘mwifiex_usb_probe’:
mwifiex/usb.c:383:41: warning: variable ‘bcd_usb’ set but not used [-Wunused-but-set-variable]
The unused variable seems to be present since 4daffe3543 which introduced
mwifiex_usb_probe().
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 92263a841b introduced mwifiex_deaggr_sdio_pkt which initializes
variable pkt_type but does not use it. Compiling with W=1 gives the following
warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_deaggr_sdio_pkt’:
mwifiex/sdio.c:1198:6: warning: variable ‘pkt_type’ set but not used [-Wunused-but-set-variable]
Fixes: 92263a841b ("mwifiex: add SDIO rx single port aggregation")
Cc: Zhaoyang Liu <liuzy@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_sdio_resume() intializes pm_flag, just like
mwifiex_sdio_suspend(), but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_sdio_resume’:
mwifiex/sdio.c:234:16: warning: variable ‘pm_flag’ set but not used [-Wunused-but-set-variable]
sdio_get_host_pm_caps() is just an acessor, so the call to it is safe
to remove. The unused variable seems to be present since
5e6e3a92b9 which introduced mwifiex_sdio_resume().
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 3935ccc14d introduced mwifiex_tm_cmd() which initializes
struct mwifiex_adapter* adapter, but doesn't use it.
Compiling with W=1 gives the following warning, fix it.
mwifiex/cfg80211.c: In function ‘mwifiex_tm_cmd’:
mwifiex/cfg80211.c:3973:26: warning: variable ‘adapter’ set but not used [-Wunused-but-set-variable]
Fixes: 3935ccc14d ("mwifiex: add cfg80211 testmode support")
Cc: Xinming Hu <huxm@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 429d90d221 introduced mwifiex_cmd_tdls_oper() which initializes
struct mwifiex_sta_node* sta_ptr, but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sta_cmd.c: In function ‘mwifiex_cmd_tdls_oper’:
mwifiex/sta_cmd.c:1732:27: warning: variable ‘sta_ptr’ set but not used [-Wunused-but-set-variable]
Fixes: 429d90d221 ("mwifiex: add cfg80211 tdls_oper handler support")
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b5413e6b22 removed all uses of chan_num in mwifiex_config_scan().
Compiling mwifiex with W=1 gives the following warning, fix it.
mwifiex/scan.c: In function ‘mwifiex_config_scan’:
mwifiex/scan.c:830:6: warning: variable ‘chan_num’ set but not used [-Wunused-but-set-variable]
Fixes: b5413e6b22 ("mwifiex: increase the number of nodes in command pool")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit bec568ff51 removed the last remaining usage of struct
mwifiex_private* priv in mwifiex_fw_dpc(), by removing the call to
mwifiex_del_virtual_intf().
Compiling mwifiex/ with W=1 gives the following warning, fix it.
mwifiex/main.c: In function ‘mwifiex_fw_dpc’:
mwifiex/main.c:520:26: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
Fixes: bec568ff51 ("mwifiex: failure path handling in mwifiex_add_virtual_intf()")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It shold reserved sizeof(ipv6hdr) for geneve in ipv6 tunnel.
Fixes: c3ef5aa5e5 ('geneve: Merge ipv4 and ipv6 geneve_build_skb()')
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In procedure mlx4_flow_steer_promisc_add(), several fields
were left uninitialized in the rule structure.
Correctly initialize these fields.
Fixes: 592e49dda8 ("net/mlx4: Implement promiscuous mode with device managed flow-steering")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user can now override the automatic driver decision using the
rx_cqe_compress flag, which is the preference for CQE compression.
The flag is initialized with the automatic driver decision.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pflags is a configuration parameter for the netdev, naturally it belongs
to priv->params.
Also introduce MLX5E_GET_PFLAG
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the self diagnostic tests to support loopback test.
The loopback test doesn't require the offline flag, it will use the
generic dev_queue_xmit and a dedicated packet_type to capture and verify
mlx5e selftest loopback packets.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The self diagnostics test implementaion include the following features:
1. Link Test: Check that link is in up state.
2. Speed Test: Check that link was negotiated correctly.
3. Health Test: Check the device health.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setdcbx interface to set the DCBX mode to firmware or os.
If setdcbx is called with mode value of zero, the DCBX mode
is set to firmware.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DBCX by default is controlled by firmware where dcbx capability bit
is set. In this mode, firmware is responsible for reading/sending the
TLV packets from/to the remote partner.
This patch sets up the infrastructure to move between HOST/FW DCBX
control mode.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add set/query commands for DCBX_PARAM register
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue description:
Current implementation saves the ETS settings from user in
a temporal soft copy and returns this settings when user
queries the ETS settings.
With the new DCBX firmware, the ETS settings can be changed
by firmware when the DCBX is in firmware controlled mode. Therefore,
user will obtain wrong values from the temporal soft copy.
Solution:
1. Read the ETS settings directly from firmware.
2. For tc_tsa:
a. Initialize tc_tsa to vendor IEEE_8021QAZ_TSA_VENDOR at netdev
creation.
b. When reading ETS setting from FW, if the traffic class bandwidth
is less than 100, set tc_tsa to IEEE_8021QAZ_TSA_ETS. This
implementation solves the scenarios when the DCBX is in FW control
and willing bit is on which means the ETS setting is dictated
by remote switch.
Also check ETS capability where needed.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCBX CEE API interface for ConnectX-4. Configurations are stored in
a temporary structure and are applied to the card's firmware when
the CEE's setall callback function is called.
Note:
priority group in CEE is equivalent to traffic class in ConnectX-4
hardware spec.
bw allocation per priority in CEE is not supported because ConnectX-4
only supports bw allocation per traffic class.
user priority in CEE does not have an equivalent term in ConnectX-4.
Therefore, user priority to priority mapping in CEE is not supported.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure firmware supports qos before exposing the DCB API.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use single queue even if multiqueue is enabled and let admin to
enable it through ethtool later. This is used to avoid possible
regression (small packet TCP stream transmission). But looks like an
overkill since:
- single queue user can disable multiqueue when launching qemu
- brings extra troubles for the management since it needs extra admin
tool in guest to enable multiqueue
- multiqueue performs much better than single queue in most of the
cases
So this patch enables multiqueue by default: if #queues is less than or
equal to #vcpu, enable as much as queue pairs; if #queues is greater
than #vcpu, enable #vcpu queue pairs.
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Marko Myllynen <myllynen@redhat.com>
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/net/ethernet/amd/xgbe/xgbe-main.c:835:12: warning: ‘xgbe_suspend’ defined
but not used [-Wunused-function]
drivers/net/ethernet/amd/xgbe/xgbe-main.c:855:12: warning: ‘xgbe_resume’ defined
but not used [-Wunused-function]
I see it during randconfig builds here.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. There are dedicated phy-modes which tell the
PHY driver to enable the RX and/or TX delays:
- PHY_INTERFACE_MODE_RGMII should disable the RX and TX delay in the
PHY (if required, the MAC should add the delays in this case)
- PHY_INTERFACE_MODE_RGMII_ID should enable RX and TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_TXID should enable the TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_RXID should enable the RX delay in the PHY
(currently not supported by RTL8211F)
With this patch we enable the TX delay for PHY_INTERFACE_MODE_RGMII_ID
and PHY_INTERFACE_MODE_RGMII_TXID.
Additionally we now explicity disable the TX-delay, which seems to be
enabled automatically after a hard-reset of the PHY (by triggering it's
reset pin) to get a consistent state (as defined by the phy-mode).
This fixes a compatibility problem with some SoCs where the TX-delay was
also added by the MAC. With the TX-delay being applied twice the TX
clock was off and TX traffic was broken or very slow (<10Mbit/s) on
1000Mbit/s links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the dev_info call that attempts to show the rate used before it is set.
Signed-off-by: Barry Day <briselec@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Barry Day <briselec@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since long already bpf_func is not only about struct sk_buff * as
input anymore. Make it generic as void *, so that callers don't
need to cast for it each time they call BPF_PROG_RUN().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use ->heap_buf after commit 46d1efd852 ("sfc: remove Software
TSO") so let's remove the last traces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvtap_newlink registers the netdev rx_handler firstly, but it
does not unregister the handler if macvlan_common_newlink failed.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() during
probe on probe errors and on driver unbind.
Also drop the of_node reference taken by of_parse_phandle() in the same
path.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() when
looking up a fixed-link phydev during probe.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() during
initialisation when later freeing the struct fman_mac.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches