Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e3aaf6494 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.
Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.
Fixes: 3e3aaf6494 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063 ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhH2rkTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklasABCAClCaAGYAOuMLWXJ9mL1K7o2u+s6M93
bSZQfke8ffFv0vNa35HLH8vXCh3QBl8BEZkN0XuXQwRSiewsWQz/W5hMZ9UcfgdR
lml6v/jaQ0nai5UrdSHJqXwm21e3M/ELFn5dE0esp1p7lSITRAbTPSyN2kNhiGyv
HLMXFPopCGEbInyo+5QA17xTPGUdMNE6J8rnRPKnMzbLgyRgZ3Jwy0furKAbzTY7
4eFiERuBErRB/tD3+oxFICcB5zyvqawnXZp+gsg5o8vm7DGZU4/WXbxOQOgwx1fK
Nw4/9FXPxUxXB925JMIn/bxjNi0OK9M96Q7bMpoa8Ik/CCkV/zKdKxIt
=0RcO
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-07
Andrey Konovalov triggered a warning in the CAN RAW layer, which is
fixed by a patch by me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to limit the number of can_filters that can be
set via setsockopt on CAN_RAW sockets. Otherwise allocations > MAX_ORDER
are not prevented resulting in a warning.
Reference: https://lkml.org/lkml/2016/12/2/230
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull sparc fix from David Miller:
"A use-before-NULL-check from Dan Carpenter"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
dbri: move dereference after check for NULL
We accidentally introduced a dereference before the NULL check in
xmit_descs() as part of silencing a GCC warning.
Fixes: 16f46050e7 ("dbri: Fix compiler warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) When dcbnl_cee_fill() fails to be able to push a new netlink
attribute, it return 0 instead of an error code. From Pan Bian.
2) Two suffix handling fixes to FIB trie code, from Alexander Duyck.
3) bnxt_hwrm_stat_ctx_alloc() goes through all the trouble of setting
and maintaining a return code 'rc' but fails to actually return it.
Also from Pan Bian.
4) ping socket ICMP handler needs to validate ICMP header length, from
Kees Cook.
5) caif_sktinit_module() has this interesting logic:
int err = sock_register(...);
if (!err)
return err;
return 0;
Just return sock_register()'s return value directly which is the
only possible correct thing to do.
6) Two bnx2x driver fixes from Yuval Mintz, return a reasonable
estimate from get_ringparam() ethtool op when interface is down and
avoid trying to use UDP port based tunneling on 577xx chips.
7) Fix ep93xx_eth crash on module unload from Florian Fainelli.
8) Missing uapi exports, from Stephen Hemminger.
9) Don't schedule work from sk_destruct(), because the socket will be
freed upon return from that function. From Herbert Xu.
10) Buggy drivers, of which we know there is at least one, can send a
huge packet into the TCP stack but forget to set the gso_size in the
SKB, which causes all kinds of problems.
Correct this when it happens, and emit a one-time warning with the
device name included so that it can be diagnosed more easily.
From Marcelo Ricardo Leitner.
11) virtio-net does DMA off the stack causes hiccups with VMAP_STACK,
fix from Andy Lutomirski.
12) Fix fec driver compilation with CONFIG_M5272, from Nikita
Yushchenko.
13) mlx5 fixes from Kamal Heib, Saeed Mahameed, and Mohamad Haj Yahia.
(erroneously flushing queues on error, module parameter validation,
etc)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
net/mlx5e: Change the SQ/RQ operational state to positive logic
net/mlx5e: Don't flush SQ on error
net/mlx5e: Don't notify HW when filling the edge of ICO SQ
net/mlx5: Fix query ISSI flow
net/mlx5: Remove duplicate pci dev name print
net/mlx5: Verify module parameters
net: fec: fix compile with CONFIG_M5272
be2net: Add DEVSEC privilege to SET_HSW_CONFIG command.
virtio-net: Fix DMA-from-the-stack in virtnet_set_mac_address()
tcp: warn on bogus MSS and try to amend it
uapi glibc compat: fix outer guard of net device flags enum
net: stmmac: clear reset value of snps, wr_osr_lmt/snps, rd_osr_lmt before writing
netlink: Do not schedule work from sk_destruct
uapi: export nf_log.h
uapi: export tc_skbmod.h
net: ep93xx_eth: Do not crash unloading module
bnx2x: Prevent tunnel config for 577xx
bnx2x: Correct ringparam estimate when DOWN
isdn: hisax: set error code on failure
net: bnx2x: fix improper return value
...
The shmem hole punching with fallocate(FALLOC_FL_PUNCH_HOLE) does not
want to race with generating new pages by faulting them in.
However, the wait-queue used to delay the page faulting has a serious
problem: the wait queue head (in shmem_fallocate()) is allocated on the
stack, and the code expects that "wake_up_all()" will make sure that all
the queue entries are gone before the stack frame is de-allocated.
And that is not at all necessarily the case.
Yes, a normal wake-up sequence will remove the wait-queue entry that
caused the wakeup (see "autoremove_wake_function()"), but the key
wording there is "that caused the wakeup". When there are multiple
possible wakeup sources, the wait queue entry may well stay around.
And _particularly_ in a page fault path, we may be faulting in new pages
from user space while we also have other things going on, and there may
well be other pending wakeups.
So despite the "wake_up_all()", it's not at all guaranteed that all list
entries are removed from the wait queue head on the stack.
Fix this by introducing a new wakeup function that removes the list
entry unconditionally, even if the target process had already woken up
for other reasons. Use that "synchronous" function to set up the
waiters in shmem_fault().
This problem has never been seen in the wild afaik, but Dave Jones has
reported it on and off while running trinity. We thought we fixed the
stack corruption with the blk-mq rq_list locking fix (commit
7fe311302f7d: "blk-mq: update hardware and software queues for sleeping
alloc"), but it turns out there was _another_ stack corruptor hiding
in the trinity runs.
Vegard Nossum (also running trinity) was able to trigger this one fairly
consistently, and made us look once again at the shmem code due to the
faults often being in that area.
Reported-and-tested-by: Vegard Nossum <vegard.nossum@oracle.com>.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 2016-12-04
Some bug fixes for mlx5 core and mlx5e driver.
v1->v2:
- replace "uint" with "unsigned int"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c52 ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are doing SQ descriptors cleanup in driver.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to do this a couple of steps ahead anyway.
Fixes: d3c9bc2743 ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".
In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).
In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate pci dev name printing from mlx5_core_warn/dbg.
Fixes: 5a7883989b ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.
Fixes: 9603b61de1 ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 80cca775cd ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cd ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_VMAP_STACK=y, virtnet_set_mac_address() can be passed a
pointer to the stack and it will OOPS. Copy the address to the heap
to prevent the crash.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: zbyszek@in.waw.pl
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been some reports lately about TCP connection stalls caused
by NIC drivers that aren't setting gso_size on aggregated packets on rx
path. This causes TCP to assume that the MSS is actually the size of the
aggregated packet, which is invalid.
Although the proper fix is to be done at each driver, it's often hard
and cumbersome for one to debug, come to such root cause and report/fix
it.
This patch amends this situation in two ways. First, it adds a warning
on when this situation occurs, so it gives a hint to those trying to
debug this. It also limit the maximum probed MSS to the adverised MSS,
as it should never be any higher than that.
The result is that the connection may not have the best performance ever
but it shouldn't stall, and the admin will have a hint on what to look
for.
Tested with virtio by forcing gso_size to 0.
v2: updated msg per David's suggestion
v3: use skb_iif to find the interface and also log its name, per Eric
Dumazet's suggestion. As the skb may be backlogged and the interface
gone by then, we need to check if the number still has a meaning.
v4: use helper tcp_gro_dev_warn() and avoid pr_warn_once inside __once, per
David's suggestion
Cc: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a wrong condition preventing the higher net device flags
IFF_LOWER_UP etc to be defined if net/if.h is included before
linux/if.h.
The comment makes it clear the intention was to allow partial
definition with either parts.
This fixes compilation of userspace programs trying to use
IFF_LOWER_UP, IFF_DORMANT or IFF_ECHO.
Fixes: 4a91cb61bb ("uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.
Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.
We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is wrong to schedule a work from sk_destruct using the socket
as the memory reserve because the socket will be freed immediately
after the return from sk_destruct.
Instead we should do the deferral prior to sk_free.
This patch does just that.
Fixes: 707693c8a4 ("netlink: Call cb->done from a worker thread")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
File is in uapi directory but not being copied on
make install_headers
Fixes commit 4ec9c8fbbc22 ("netfilter: nft_log: complete
NFTA_LOG_FLAGS attr support").
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes commit 735cffe5d800 ("net_sched: Introduce skbmod action")
Not used by iproute2 but maybe in future.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we unload the ep93xx_eth, whether we have opened the network
interface or not, we will either hit a kernel paging request error, or a
simple NULL pointer de-reference because:
- if ep93xx_open has been called, we have created a valid DMA mapping
for ep->descs, when we call ep93xx_stop, we also call
ep93xx_free_buffers, ep->descs now has a stale value
- if ep93xx_open has not been called, we have a NULL pointer for
ep->descs, so performing any operation against that address just won't
work
Fix this by adding a NULL pointer check for ep->descs which means that
ep93xx_free_buffers() was able to successfully tear down the descriptors
and free the DMA cookie as well.
Fixes: 1d22e05df8 ("[PATCH] Cirrus Logic ep93xx ethernet driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
bnx2x: fixes series
Two unrelated fixes for bnx2x - the first one is nice-to-have,
while the other fixes fatal behaviour in older adapters.
Please consider applying them to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the 578xx adapters are capable of configuring UDP ports for
the purpose of tunnelling - doing the same on 577xx might lead to
a firmware assertion.
We're already not claiming support for any related feature for such
devices, but we also need to prevent the configuration of the UDP
ports to the device in this case.
Fixes: f34fa14cc0 ("bnx2x: Add vxlan RSS support")
Reported-by: Anikina Anna <anikina@gmail.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until interface is up [and assuming ringparams weren't explicitly
configured] when queried for the size of its rings bnx2x would
claim they're the maximal size by default.
That is incorrect as by default the maximal number of buffers would
be equally divided between the various rx rings.
This prevents the user from actually setting the number of elements
on each rx ring to be of maximal size prior to transitioning the
interface into up state.
To fix this, make a rough estimation about the number of buffers.
It wouldn't always be accurate, but it would be much better than
current estimation and would allow users to increase number of
buffers during early initialization of the interface.
Reported-by: Seymour, Shane <shane.seymour@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function hfc4s8s_probe(), the value of return variable err should be
negative on failures. However, when the call to request_region() returns
NULL, the value of err is 0. This patch fixes the bug, assigning
"-EBUSY" to err on the path that request_region() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188931
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro BNX2X_ALLOC_AND_SET(arr, lbl, func) calls kmalloc() to allocate
memory, and jumps to label "lbl" if the allocation fails. Label "lbl"
first cleans memory and then returns variable rc. Before calling the
macro, the value of variable rc is 0. Because 0 means no error, the
callers of bnx2x_init_firmware() may be misled. This patch fixes the bug,
assigning "-ENOMEM" to rc before calling macro NX2X_ALLOC_AND_SET().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189141
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling dma_mapping_error(), the value of return variable rc is 0.
And when the call returns an unexpected value, rc is not set to a
negative errno. Thus, it will return 0 on the error path, and its
callers cannot detect the bug. This patch fixes the bug, assigning
"-ENOMEM" to err.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189041
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It returns variable "error" when ioremap_nocache() returns a NULL
pointer. The value of "error" is 0 then, which will mislead the callers
to believe that there is no error. This patch fixes the bug, returning
"-ENOMEM".
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189021
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the calls to kzalloc() fail, the value of return variable ret may
be 0. 0 means success in this context. This patch fixes the bug,
assigning "-ENOMEM" to ret before calling kzalloc().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188971
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check of the return value of sock_register() is ineffective.
"if(!err)" seems to be a typo. It is better to propagate the error code
to the callers of caif_sktinit_module(). This patch removes the check
statment and directly returns the result of sock_register().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188751
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit c0371da604 ("put iov_iter into msghdr") in v3.19, there
was no check that the iovec contained enough bytes for an ICMP header,
and the read loop would walk across neighboring stack contents. Since the
iov_iter conversion, bad arguments are noticed, but the returned error is
EFAULT. Returning EINVAL is a clearer error and also solves the problem
prior to v3.19.
This was found using trinity with KASAN on v3.18:
BUG: KASAN: stack-out-of-bounds in memcpy_fromiovec+0x60/0x114 at addr ffffffc071077da0
Read of size 8 by task trinity-c2/9623
page:ffffffbe034b9a08 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: kasan: bad access detected
CPU: 0 PID: 9623 Comm: trinity-c2 Tainted: G BU 3.18.0-dirty #15
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc000209c98>] dump_backtrace+0x0/0x1ac arch/arm64/kernel/traps.c:90
[<ffffffc000209e54>] show_stack+0x10/0x1c arch/arm64/kernel/traps.c:171
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc000f18dc4>] dump_stack+0x7c/0xd0 lib/dump_stack.c:50
[< inline >] print_address_description mm/kasan/report.c:147
[< inline >] kasan_report_error mm/kasan/report.c:236
[<ffffffc000373dcc>] kasan_report+0x380/0x4b8 mm/kasan/report.c:259
[< inline >] check_memory_region mm/kasan/kasan.c:264
[<ffffffc00037352c>] __asan_load8+0x20/0x70 mm/kasan/kasan.c:507
[<ffffffc0005b9624>] memcpy_fromiovec+0x5c/0x114 lib/iovec.c:15
[< inline >] memcpy_from_msg include/linux/skbuff.h:2667
[<ffffffc000ddeba0>] ping_common_sendmsg+0x50/0x108 net/ipv4/ping.c:674
[<ffffffc000dded30>] ping_v4_sendmsg+0xd8/0x698 net/ipv4/ping.c:714
[<ffffffc000dc91dc>] inet_sendmsg+0xe0/0x12c net/ipv4/af_inet.c:749
[< inline >] __sock_sendmsg_nosec net/socket.c:624
[< inline >] __sock_sendmsg net/socket.c:632
[<ffffffc000cab61c>] sock_sendmsg+0x124/0x164 net/socket.c:643
[< inline >] SYSC_sendto net/socket.c:1797
[<ffffffc000cad270>] SyS_sendto+0x178/0x1d8 net/socket.c:1761
CVE-2016-8399
Reported-by: Qidan He <i@flanker017.me>
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four fixes, the first for code we merged this cycle and three that are also
going to stable:
- On 64-bit Book3E we were not placing the .text section where we said we would
in the asm.
- We broke building the boot wrapper on some 32-bit toolchains.
- Lazy icache flushing was broken on pre-POWER5 machines.
- One of the error paths in our EEH code would lead to a deadlock.
Thanks to:
Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6IL4
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Four fixes, the first for code we merged this cycle and three that are
also going to stable:
- On 64-bit Book3E we were not placing the .text section where we
said we would in the asm.
- We broke building the boot wrapper on some 32-bit toolchains.
- Lazy icache flushing was broken on pre-POWER5 machines.
- One of the error paths in our EEH code would lead to a deadlock.
Thanks to: Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt,
Nicholas Piggin"
* tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix placement of .text to be immediately following .head.text
powerpc/eeh: Fix deadlock when PE frozen state can't be cleared
powerpc/mm: Fix lazy icache flush on pre-POWER5
powerpc/boot: Fix build failure in 32-bit boot wrapper
In function lanai_dev_open(), when the call to ioremap() fails, the
value of return variable result is 0. 0 means no error in this context.
This patch fixes the bug, assigning "-ENOMEM" to result when ioremap()
returns a NULL pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188791
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function lan78xx_probe(), variable ret takes the errno code on
failures. However, when the call to usb_alloc_urb() fails, its value
will keeps 0. 0 indicates success in the context, which is inconsistent
with the execution result. This patch fixes the bug, assigning
"-ENOMEM" to ret when usb_alloc_urb() returns a NULL pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188771
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function br_sysfs_addbr() does not set error code when the call
kobject_create_and_add() returns a NULL pointer. It may be better to
return "-ENOMEM" when kobject_create_and_add() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188781
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding space after switch keyword before open
parenthesis for readability purpose.
This patch fixes the checkpatch.pl warning:
space required before the open parenthesis '('
Signed-off-by: Suraj Deshmukh <surajssd009005@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function bnxt_hwrm_stat_ctx_alloc() always returns 0, even if the call
to _hwrm_send_message() fails. It may be better to propagate the errors
to the caller of bnxt_hwrm_stat_ctx_alloc().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188661
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
IPv4 FIB suffix length fixes
In reviewing the patch from Robert Shearman and looking over the code I
realized there were a few different bugs we were still carrying in the IPv4
FIB lookup code.
These two patches are based off of Robert's original patch, but take things
one step further by splitting them up to address two additional issues I
found.
So first have Robert's original patch which was addressing the fact that
us calling update_suffix in resize is expensive when it is called per add.
To address that I incorporated the core bit of the patch which was us
dropping the update_suffix call from resize.
The first patch in the series does a rename and fix on the push_suffix and
pull_suffix code. Specifically we drop the need to pass a leaf and
secondly we fix things so we pull the suffix as long as the value of the
suffix in the node is dropping.
The second patch addresses the original issue reported as well as
optimizing the code for the fact that update_suffix is only really meant to
go through and clean things up when we are decreasing a suffix. I had
originally added code for it to somehow cause an increase, but if we push
the suffix when a new leaf is added we only ever have to handle pulling
down the suffix with update_suffix so I updated the code to reflect that.
As far as side effects the only ones I think that will be obvious should be
the fact that some routes may be able to be found earlier since before we
relied on resize to update the suffix lengths, and now we are updating them
before we add or remove the leaf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that update_suffix can be expensive when it is called
on a large node in which most of the suffix lengths are the same. The time
required to add 200K entries had increased from around 3 seconds to almost
49 seconds.
In order to address this we need to move the code for updating the suffix
out of resize and instead just have it handled in the cases where we are
pushing a node that increases the suffix length, or will decrease the
suffix length.
Fixes: 5405afd1a3 ("fib_trie: Add tracking value for suffix length")
Reported-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wasn't necessary to pass a leaf in when doing the suffix updates so just
drop it. Instead just pass the suffix and work with that.
Since we dropped the leaf there is no need to include that in the name so
the names are updated to node_push_suffix and node_pull_suffix.
Finally I noticed that the logic for pulling the suffix length back
actually had some issues. Specifically it would stop prematurely if there
was a longer suffix, but it was not as long as the original suffix. I
updated the code to address that in node_pull_suffix.
Fixes: 5405afd1a3 ("fib_trie: Add tracking value for suffix length")
Suggested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function dcbnl_cee_fill(), returns the value of variable err on
errors. However, on some error paths (e.g. nla put fails), its value may
be 0. It may be better to explicitly set a negative errno to variable
err before returning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188881
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"A pretty small pull request: a couple of AMD powerxpress regression
fixes and a power management fix, a couple of i915 fixes and one hdlcd
fix, along with one core don't oops because of incorrect API usage fix"
* tag 'drm-fixes-for-v4.9-rc8' of git://people.freedesktop.org/~airlied/linux:
drm/i915: drop the struct_mutex when wedged or trying to reset
drm/i915: Don't touch NULL sg on i915_gem_object_get_pages_gtt() error
drm: Don't call drm_for_each_crtc with a non-KMS driver
drm/radeon: fix check for port PM availability
drm/amdgpu: fix check for port PM availability
drm/amd/powerplay: initialize the soft_regs offset in struct smu7_hwmgr
drm: hdlcd: Fix cleanup order
Daniele Palmas