The switches supported so far by the driver only have non-SerDes ports,
so they should be configured in the PHYLINK callback that provides the
resolved PHY link parameters.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7df ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inner pair of parentheses should be around the variable x
Fixes: 37feab6076 ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify ksz_common.c by using delayed_work instead of a combination of
timer and work.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port.
MT7530 supports one monitor port and multiple mirrored ports.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to other DSA switches, in the Ocelot cores, the RX filtering is
a much more important concern.
Firstly, the primary use case for Ocelot is non-DSA, so there isn't any
secondary Ethernet MAC [the DSA master's one] to implicitly drop frames
having a DMAC we are not interested in. So the switch driver itself
needs to install FDB entries towards the CPU port module (PGID_CPU) for
the MAC address of each switch port, in each VLAN installed on the port.
Every address that is not whitelisted is implicitly dropped. This is in
order to achieve a behavior similar to N standalone net devices.
Secondly, even in the secondary use case of DSA, such as illustrated by
Felix with the NPI port mode, that secondary Ethernet MAC is present,
but its RX filter is bypassed. This is because the DSA tags themselves
are placed before Ethernet, so the DMAC that the switch ports see is
not seen by the DSA master too (since it's shifter to the right).
So RX filtering is pretty important. A good RX filter won't bother the
CPU in case the switch port receives a frame that it's not interested
in, and there exists no other line of defense.
Ocelot is pretty strict when it comes to RX filtering: non-IP multicast
and broadcast traffic is allowed to go to the CPU port module, but
unknown unicast isn't. This means that traffic reception for any other
MAC addresses than the ones configured on each switch port net device
won't work. This includes use cases such as macvlan or bridging with a
non-Ocelot (so-called "foreign") interface. But this seems to be fine
for the scenarios that the Linux system embedded inside an Ocelot switch
is intended for - it is simply not interested in unknown unicast
traffic, as explained in Allan Nielsen's presentation [0].
On the other hand, the Felix DSA switch is integrated in more
general-purpose Linux systems, so it can't afford to drop that sort of
traffic in hardware, even if it will end up doing so later, in software.
Actually, unknown unicast means more for Felix than it does for Ocelot.
Felix doesn't attempt to perform the whitelisting of switch port MAC
addresses towards PGID_CPU at all, mainly because it is too complicated
to be feasible: while the MAC addresses are unique in Ocelot, by default
in DSA all ports are equal and inherited from the DSA master. This adds
into account the question of reference counting MAC addresses (delayed
ocelot_mact_forget), not to mention reference counting for the VLAN IDs
that those MAC addresses are installed in. This reference counting
should be done in the DSA core, and the fact that it wasn't needed so
far is due to the fact that the other DSA switches don't have the DSA
tag placed before Ethernet, so the DSA master is able to whitelist the
MAC addresses in hardware.
So this means that even regular traffic termination on a Felix switch
port happens through flooding (because neither Felix nor Ocelot learn
source MAC addresses from CPU-injected frames).
So far we've explained that whitelisting towards PGID_CPU:
- helps to reduce the likelihood of spamming the CPU with frames it
won't process very far anyway
- is implemented in the ocelot driver
- is sufficient for the ocelot use cases
- is not feasible in DSA
- breaks use cases in DSA, in the current status (whitelisting enabled
but no MAC address whitelisted)
So the proposed patch allows unknown unicast frames to be sent to the
CPU port module. This is done for the Felix DSA driver only, as Ocelot
seems to be happy without it.
[0]: https://www.youtube.com/watch?v=B1HhxEcU7Jg
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.
Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate 100baseT1_Full to make this driver work with TJA1102 PHY.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the switch is not hardware reset on a warm boot, interrupts can be
left enabled, and possibly pending. This will cause us to enter an
infinite loop trying to service an interrupt we are unable to handle,
thereby preventing the kernel from booting.
Ensure that the global 2 interrupt sources are disabled before we claim
the parent interrupt.
Observed on the ZII development revision B and C platforms with
reworked serdes support, and using reboot -f to reboot the platform.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing ~ to the usage of the mask.
Reported-by: Kevin Benson <Kevin.Benson@zii.aero>
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 5c74c54ce6 ("net: dsa: mv88e6xxx: Split monitor port configuration")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the resolved link configuration to set the MAC configuration when
mac_link_up() for non-internal-PHY ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting VLANs on DSA switches, the VLAN is added to both the port
concerned as well as the CPU port by dsa_slave_vlan_add(), as well as
any DSA ports. If multiple ports are configured with the same VLAN ID,
this triggers a warning on the CPU and DSA ports.
Avoid this warning for CPU and DSA ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Fixes: de34d7084e ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7458bd540f ("net: dsa:
bcm_sf2: Also configure Port 5 for 2Gb/sec on 7278") as it causes
advanced congestion buffering issues with 7278 switch devices when using
their internal Giabit PHY. While this is being debugged, continue with
conservative defaults that work and do not cause packet loss.
Fixes: 7458bd540f ("net: dsa: bcm_sf2: Also configure Port 5 for 2Gb/sec on 7278")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy-mode = "gmii" is confusing because it may mean that the port
supports the 8-bit-wide parallel data interface pinout, which it
doesn't.
It may also be confusing because one of the "gmii" internal ports is
actually overclocked to run at 2.5Gbps (even though, yes, as far as the
switch MAC is concerned, it still thinks it's gigabit).
So use the phy-mode = "internal" property to describe the internal ports
inside the NXP LS1028A chip (the ones facing the ENETC). The change
should be fine, because the device tree bindings document is yet to be
introduced, and there are no stable DT blobs in use.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has upto 8 sets of PCS registers, depending on how ports
9 and 10 are configured. The can be spread over 8 ports. If a port has
a PCS register set, return it along with the port registers. The
register space is sparse, so hard code a list of registers which will
be returned. It can later be extended, if needed, by append to the end
of the list.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352 has one PCS which can be used for 1000BaseX or
SGMII. Add the registers to the dump for the port which the PCS is
associated to.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool provides a generic mechanism for a driver to return the
registers of an ethernet device. DSA uses this to give the port
registers associated with an interfaces. Extend this to allow PCS
registers to also be returned, if the port has a PCS associated to it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Either port 5 or port 8 can be used on a 7278 device, make sure that
port 5 also gets configured properly for 2Gb/sec in that case.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure that the default VID is untagged otherwise the switch
will be sending tagged frames and the results can be problematic. This
is especially true with b53 switches that use VID 0 as their default
VLAN since VID 0 has a special meaning.
Fixes: fea8335317 ("net: dsa: b53: Fix default VLAN ID")
Fixes: 061f6a505a ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for unique interrupt names, after testing on a few
devices, it was assumed 32 characters would be sufficient. This
assumption turned out to be incorrect, ZII RDU2 for example uses a
device base name of mv88e6xxx-30be0000.ethernet-1:0, leaving no space
for post fixes such as -g1-atu-prob and -watchdog. The names then
become identical, defeating the point of the patch.
Increase the length of the string to 64 charactoes.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 3095383a8a ("net: dsa: mv88e6xxx: Unique IRQ name")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c645 ("net: dsa: b53: Properly account for VLAN filtering")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SERDES statistics are valid for all members of the 6390 family,
not just the 6390 itself. Add the needed callbacks to all members of
the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the serdes link is set to 2500 using interfce type 2500base-X, lower
link speeds over on the line side should still be supported.
Rate adaptation is done out of band, in our case using AQR PHYs this is
done using flow control.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control is used with 2500Base-X and AQR PHYs to do rate adaptation
between line side 100/1000 links and MAC running at 2.5G.
This is independent of the flow control configuration settled on line
side though AN.
In general, allowing the MAC to handle flow control even if not
negotiated with the link partner should not be a problem, so the patch
just enables it in all cases.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs like VSC8234 don't like it when AN restarts on their system side
and they restart line side AN too, going into an endless link up/down loop.
Don't restart PCS AN if link is up already.
Although in theory this feedback loop should be possible with the other
in-band AN modes too, for some reason it was not seen with the VSC8514
QSGMII and AQR412 USXGMII PHYs. So keep this logic only for SGMII where
the problem was found.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some PHYs (AQR412) don't advertise copper-side link status
during system side AN.
So remove this duplicate assignment to pcs->link and rely on the
previous one for link state: the local indication from the MAC PCS.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM531x5 and BCM539x families require that the IMP port be enabled
within the management page and that management mode (SM_SW_FWD_MODE) be
turned on. Once this is done, everything works as expected, including
multicast with standalone DSA devices or bridge devices.
Because such switches are frequencly cascaded with other internal
Broadcom switches on which we want to enable Broadcom tags, update
b53_can_enable_brcm_tags() to check the kind of DSA master tagging
protocol being used, if it is one of the two supported Broadcom tagging
protocols, force DSA_TAG_PROTO_NONE.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique interrupt name for the VTU and ATU,
based on the device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique g2 interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique watchdog interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique SERDES interrupt name, based on the
device name and the port the SERDES is for. For example:
95: 3 mv88e6xxx-g2 9 Edge mv88e6xxx-0.2:00-serdes-9
96: 0 mv88e6xxx-g2 10 Edge mv88e6xxx-0.2:00-serdes-10
The 0.2:00 indicates the switch and -9 indicates port 9.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique switch interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a6 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Layerscape SoCs traditionally expose the SerDes configuration/status for
Ethernet protocols (PCS for SGMII/USXGMII/10GBase-R etc etc) in a register
format that is compatible with clause 22 or clause 45 (depending on
SerDes protocol). Each MAC has its own internal MDIO bus on which there
is one or more of these PCS's, responding to commands at a configurable
PHY address. The per-port internal MDIO bus (which is just for PCSs) is
totally separate and has nothing to do with the dedicated external MDIO
controller (which is just for PHYs), but the register map for the MDIO
controller is the same.
The VSC9959 (Felix) switch instantiated in the LS1028A is integrated
in hardware with the ENETC PCS of its DSA master, and reuses its MDIO
controller driver, so Felix has been made to depend on it in Kconfig.
+------------------------------------------------------------------------+
| +--------+ GMII (typically disabled via RCW) |
| ENETC PCI | ENETC |--------------------------+ |
| Root Complex | port 3 |-----------------------+ | |
| Integrated +--------+ | | |
| Endpoint | | |
| +--------+ 2.5G GMII | | |
| | ENETC |--------------+ | | |
| | port 2 |-----------+ | | | |
| +--------+ | | | | |
| +--------+ +--------+ |
| | Felix | | Felix | |
| | port 4 | | port 5 | |
| +--------+ +--------+ |
| |
| +--------+ +--------+ +--------+ +--------+ +--------+ +--------+ |
| | ENETC | | ENETC | | Felix | | Felix | | Felix | | Felix | |
| | port 0 | | port 1 | | port 0 | | port 1 | | port 2 | | port 3 | |
+------------------------------------------------------------------------+
| |||| SerDes | |||| |||| |||| |||| |
| +--------+block | +--------------------------------------------+ |
| | ENETC | | | ENETC port 2 internal MDIO bus | |
| | port 0 | | | PCS PCS PCS PCS | |
| | PCS | | | 0 1 2 3 | |
+-----------------|------------------------------------------------------+
v v v v v v
SGMII/ RGMII QSGMII/QSXGMII/4xSGMII/4x1000Base-X/4x2500Base-X
USXGMII/ (bypasses
1000Base-X/ SerDes)
2500Base-X
In the LS1028A SoC described above, the VSC9959 Felix switch is PF5 of
the ENETC root complex, and has 2 BARs:
- BAR 4: the switch's effective registers
- BAR 0: the MDIO controller register map lended from ENETC port 2
(PF2), for accessing its associated PCS's.
This explanation is necessary because the patch does some renaming
"pci_bar" -> "switch_pci_bar" for clarity, which would otherwise appear
a bit obtuse.
The fact that the internal MDIO bus is "borrowed" is relevant because
the register map is found in PF5 (the switch) but it triggers an access
fault if PF2 (the ENETC DSA master) is not enabled. This is not treated
in any way (and I don't think it can be treated).
All of this is so SoC-specific, that it was contained as much as
possible in the platform-integration file felix_vsc9959.c.
We need to parse and pre-validate the device tree because of 2 reasons:
- The PHY mode (SerDes protocol) cannot change at runtime due to SoC
design.
- There is a circular dependency in that we need to know what clause the
PCS speaks in order to find it on the internal MDIO bus. But the
clause of the PCS depends on what phy-mode it is configured for.
The goal of this patch is to make steps towards removing the bootloader
dependency for SGMII PCS pre-configuration, as well as to add support
for monitoring the in-band SGMII AN between the PCS and the system-side
link partner (PHY or other MAC).
In practice the bootloader dependency is not completely removed. U-Boot
pre-programs the PHY address at which each PCS can be found on the
internal MDIO bus (MDEV_PORT). This is needed because the PCS of each
port has the same out-of-reset PHY address of zero. The SerDes register
for changing MDEV_PORT is pretty deep in the SoC (outside the addresses
of the ENETC PCI BARs) and therefore inaccessible to us from here.
Felix VSC9959 and Ocelot VSC7514 are integrated very differently in
their respective SoCs, and for that reason Felix does not use the Ocelot
core library for PHYLINK. On one hand we don't want to impose the
fixed phy-mode limitation to Ocelot, and on the other hand Felix doesn't
need to force the MAC link speed the way Ocelot does, since the MAC is
connected to the PCS through a fixed GMII, and the PCS is the one who
does the rate adaptation at lower link speeds, which the MAC does not
even need to know about. In fact changing the GMII speed for Felix
irrecoverably breaks transmission through that port until a reset.
The pair with ENETC port 3 and Felix port 5 is optional and doesn't
support tagging. When we enable it, swp5 is a regular slave port, albeit
an internal one. The trouble is that it doesn't work, and that is
because the DSA PHYLIB adaptation layer doesn't treat fixed-link slave
ports. So that is yet another reason for wanting to convert Felix to the
native PHYLINK API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I finally found out how the 4 management route slots are supposed to
be used, but.. it's not worth it.
The description from the comment I've just deleted in this commit is
still true: when more than 1 management slot is active at the same time,
the switch will match frames incoming [from the CPU port] on the lowest
numbered management slot that matches the frame's DMAC.
My issue was that one was not supposed to statically assign each port a
slot. Yes, there are 4 slots and also 4 non-CPU ports, but that is a
mere coincidence.
Instead, the switch can be used like this: every management frame gets a
slot at the right of the most recently assigned slot:
Send mgmt frame 1 through S0: S0 x x x
Send mgmt frame 2 through S1: S0 S1 x x
Send mgmt frame 3 through S2: S0 S1 S2 x
Send mgmt frame 4 through S3: S0 S1 S2 S3
The difference compared to the old usage is that the transmission of
frames 1-4 doesn't need to wait until the completion of the management
route. It is safe to use a slot to the right of the most recently used
one, because by protocol nobody will program a slot to your left and
"steal" your route towards the correct egress port.
So there is a potential throughput benefit here.
But mgmt frame 5 has no more free slot to use, so it has to wait until
_all_ of S0, S1, S2, S3 are full, in order to use S0 again.
And that's actually exactly the problem: I was looking for something
that would bring more predictable transmission latency, but this is
exactly the opposite: 3 out of 4 frames would be transmitted quicker,
but the 4th would draw the short straw and have a worse worst-case
latency than before.
Useless.
Things are made even worse by PTP TX timestamping, which is something I
won't go deeply into here. Suffice to say that the fact there is a
driver-level lock on the SPI bus offsets any potential throughput gains
that parallelism might bring.
So there's no going back to the multi-slot scheme, remove the
"mgmt_slot" variable from sja1105_port and the dummy static assignment
made at probe time.
While passing by, also remove the assignment to casc_port altogether.
Don't pretend that we support cascaded setups.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no build time dependency on CONFIG_OF, but we do need to make
sure we gate the initialization of the gpio_chip::of_node member with a
proper check on CONFIG_OF_GPIO. This enables the driver to build on
platforms that do not have CONFIG_OF enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling PTP timestamping, don't reset the switch with the new
static config until all existing PTP frames have been timestamped on the
RX path or dropped. There's nothing we can do with these afterwards.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And move the queue of skb's waiting for RX timestamps into the ptp_data
structure, since it isn't needed if PTP is not compiled.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b3 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If packet checker is enabled in the serdes, then Rx counter registers
start working, and no side effects have been detected.
This patch enables packet checker automatically when powering serdes on,
and exposes Rx counter registers via ethtool statistics interface.
Code partially basded by older attempt by Andrew Lunn.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set variable 'mbus' static
since new value always be assigned before use it.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide basic support for Atheros AR9331 built-in switch. So far it
works as port multiplexer without any hardware offloading support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting MSCC_OCELOT_SWITCH is not possible when NET_VENDOR_MICROSEMI
is disabled:
WARNING: unmet direct dependencies detected for MSCC_OCELOT_SWITCH
Depends on [n]: NETDEVICES [=y] && ETHERNET [=n] && NET_VENDOR_MICROSEMI [=n] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y]
Selected by [m]:
- NET_DSA_MSCC_FELIX [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && NET_DSA [=y] && PCI [=y]
Add a Kconfig dependency on NET_VENDOR_MICROSEMI, which also implies
CONFIG_NETDEVICES.
Depending on a vendor config violates menuconfig locality for the DSA
driver, but is the smallest compromise since all other solutions are
much more complicated (see [0]).
https://www.spinics.net/lists/netdev/msg618808.html
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several issues with 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback") that resulted in breaking connectivity for standalone ports:
- both user and CPU ports must allow unicast and multicast forwarding by
default otherwise this just flat out breaks connectivity for
standalone DSA ports
- IP multicast is treated similarly as multicast, but has separate
control registers
- the UC, MC and IPMC lookup failure register offsets were wrong, and
instead used bit values that are meaningful for the
B53_IP_MULTICAST_CTRL register
Fixes: 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was using configuration of port 0 in devicetree for all ports.
In case CPU port was not 0, the delay settings was ignored. This resulted not
working communication between CPU and the switch.
Fixes: f5b8631c29 ("net: dsa: sja1105: Error out if RGMII delays are requested in DT")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse warnings:
drivers/net/dsa/ocelot/felix.c:351:6: warning: symbol 'felix_txtstamp' was not declared. Should it be static?
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define PTP registers for felix_vsc9959.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch
and the ENETC:
- eno2 <-> swp4, at 2.5G
- eno3 <-> swp5, at 1G
Only one of the above Ethernet port pairs can act as a DSA link for
tagging.
When adding initial support for the driver, it was tested only on the 1G
eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially
(which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't
support fixed-link speeds higher than 1G).
After making PHYLINK work, it appears that swp4 still can't act as CPU
port. So it looks like ocelot_set_cpu_port was being called for swp4,
but then it was called again for swp5, overwriting the CPU port assigned
in the DT.
It appears that when you call dsa_upstream_port for a port that is not
defined in the device tree (such as swp5 when using swp4 as CPU port),
its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu,
and this trips up the following condition in dsa_upstream_port:
if (!cpu_dp)
return port;
So the moral of the story is: don't call dsa_upstream_port for a port
that is not defined in the device tree, and therefore its dsa_port
structure is not completely initialized (ds->num_ports is still 6).
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver enables rising edge or falling edge, but not both, and so
this patch validates that the request contains only one of the two
edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the mv88e6xxx PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
For the record, the semantics of this driver are:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp rising edge
Cc: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This supports an Ethernet switching core from Vitesse / Microsemi /
Microchip (VSC9959) which is part of the Ocelot family (a brand name),
and whose code name is Felix. The switch can be (and is) integrated on
different SoCs as a PCIe endpoint device.
The functionality is provided by the core of the Ocelot switch driver
(drivers/net/ethernet/mscc). In this regard, the current driver is an
instance of Microsemi's Ocelot core driver, with a DSA front-end. It
inherits its name from VSC9959's code name, to distinguish itself from
the switchdev ocelot driver.
The patch adds the logic for probing a PCI device and defines the
register map for the VSC9959 switch core, since it has some differences
in register addresses and bitfield mappings compared to the other Ocelot
switches (VSC7511, VSC7512, VSC7513, VSC7514).
The Felix driver declares the register map as part of the "instance
table". Currently the VSC9959 inside NXP LS1028A is the only instance,
but presumably it can support other switches in the Ocelot family, when
used in DSA mode (Linux running on the external CPU, and not on the
embedded MIPS).
In a few cases, some h/w operations have to be done differently on
VSC9959 due to missing bitfields. This is the case for the switch core
reset and init. Because for this operation Ocelot uses some bits that
are not present on Felix, the latter has to use a register from the
global registers block (GCB) instead.
Although it is a PCI driver, it relies on DT bindings for compatibility
with DSA (CPU port link, PHY library). It does not have any custom
device tree bindings, since we would like to minimize its dependency on
device tree though.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't really need 10k species of reset. Remove everything except cold
reset which is what is actually used. Too bad the hardware designers
couldn't agree to use the same bit field for rev 1 and rev 2, so the
(*reset_cmd) function pointer is there to stay.
However let's simplify the prototype and give it a struct dsa_switch (we
want to avoid forward-declarations of structures, in this case struct
sja1105_private, wherever we can).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested using the following bash script and the tc from iproute2-next:
#!/bin/bash
set -e -u -o pipefail
NSEC_PER_SEC="1000000000"
gatemask() {
local tc_list="$1"
local mask=0
for tc in ${tc_list}; do
mask=$((${mask} | (1 << ${tc})))
done
printf "%02x" ${mask}
}
if ! systemctl is-active --quiet ptp4l; then
echo "Please start the ptp4l service"
exit
fi
now=$(phc_ctl /dev/ptp1 get | gawk '/clock time is/ { print $5; }')
# Phase-align the base time to the start of the next second.
sec=$(echo "${now}" | gawk -F. '{ print $1; }')
base_time="$(((${sec} + 1) * ${NSEC_PER_SEC}))"
tc qdisc add dev swp5 parent root handle 100 taprio \
num_tc 8 \
map 0 1 2 3 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S $(gatemask 7) 100000 \
sched-entry S $(gatemask "0 1 2 3 4 5 6") 400000 \
clockid CLOCK_TAI flags 2
The "state machine" is a workqueue invoked after each manipulation
command on the PTP clock (reset, adjust time, set time, adjust
frequency) which checks over the state of the time-aware scheduler.
So it is not monitored periodically, only in reaction to a PTP command
typically triggered from a userspace daemon (linuxptp). Otherwise there
is no reason for things to go wrong.
Now that the timecounter/cyclecounter has been replaced with hardware
operations on the PTP clock, the TAS Kconfig now depends upon PTP and
the standalone clocksource operating mode has been removed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTPSTRTSCH and PTPSTOPSCH bits are actually readable and indicate
whether the time-aware scheduler is running or not. We will be using
that for monitoring the scheduler in the next patch, so refactor the PTP
command API in order to allow that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it can be quite opaque even for me why the driver decided to
reset the switch. So instead of adding dump_stack() calls each time for
debugging, just add a reset reason to sja1105_static_config_reload
calls which gets printed to the console.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a stray semicolon in an if statement that will cause a dev_err
message to be printed unconditionally. Fix this by removing the stray
semicolon.
Addresses-Coverity: ("Stay semicolon")
Fixes: f0942e00a1 ("net: dsa: mv88e6xxx: Add support for port mirroring")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.
It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose here is to avoid ptp4l fail due to this condition:
timed out while polling for tx timestamp
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
port 1: send peer delay request failed
So either reset the switch before the management frame was sent, or
after it was timestamped as well, but not in the middle.
The condition may arise either due to a true timeout (i.e. because
re-uploading the static config takes time), or due to the TX timestamp
actually getting lost due to reset. For the former we can increase
tx_timestamp_timeout in userspace, for the latter we need this patch.
Locking all traffic during switch reset does not make sense at all,
though. Forcing all CPU-originated traffic to potentially block waiting
for a sleepable context to send > 800 bytes over SPI is not a good idea.
Flows that are autonomously forwarded by the switch will get dropped
anyway during switch reset no matter what. So just let all other
CPU-originated traffic be dropped as well.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP time of the switch is not preserved when uploading a new static
configuration. Work around this hardware oddity by reading its PTP time
before a static config upload, and restoring it afterwards.
Static config changes are expected to occur at runtime even in scenarios
directly related to PTP, i.e. the Time-Aware Scheduler of the switch is
programmed in this way.
Perhaps the larger implication of this patch is that the PTP .gettimex64
and .settime functions need to be exposed to sja1105_main.c, where the
PTP lock needs to be held during this entire process. So their core
implementation needs to move to some common functions which get exposed
in sja1105_ptp.h.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through the PTP_SYS_OFFSET_EXTENDED ioctl, it is possible for userspace
applications (i.e. phc2sys) to compensate for the delays incurred while
reading the PHC's time.
The task itself of taking the software timestamp is delegated to the SPI
subsystem, through the newly introduced API in struct spi_transfer. The
goal is to cross-timestamp I/O operations on the switch's PTP clock with
values in the local system clock (CLOCK_REALTIME). For that we need to
understand a bit of the hardware internals.
The 'read PTP time' message is a 12 byte structure, first 4 bytes of
which represent the SPI header, and the last 8 bytes represent the
64-bit PTP time. The switch itself starts processing the command
immediately after receiving the last bit of the address, i.e. at the
middle of byte 3 (last byte of header). The PTP time is shadowed to a
buffer register in the switch, and retrieved atomically during the
subsequent SPI frames.
A similar thing goes on for the 'write PTP time' message, although in
that case the switch waits until the 64-bit PTP time becomes fully
available before taking any action. So the byte that needs to be
software-timestamped is byte 11 (last) of the transfer.
The patch creates a common (and local) sja1105_xfer implementation for
the SPI I/O, and offers 3 front-ends:
- sja1105_xfer_u32 and sja1105_xfer_u64: these are capable of optionally
requesting a PTP timestamp
- sja1105_xfer_buf: this is for large transfers (e.g. the static config
buffer) and other misc data, and there is no point in giving
timestamping capabilities to this.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g2_atu_stats_get() takes two parameters. Make the stub
function also take two, otherwise we get compile errors.
Fixes: c5f299d592 ("net: dsa: mv88e6xxx: global1_atu: Add helper for get next")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab an optional and exclusive reset controller line for the switch and
manage it during probe/remove functions accordingly. For 7278 devices we
change bcm_sf2_sw_rst() to use the reset controller line since the
WATCHDOG_CTRL register does not reset the switch contrary to stated
documentation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the DSA core doing the call to dsa_port_disable() we do not need to
do that within the driver itself. This could cause an use after free
since past dsa_unregister_switch() we should not be accessing any
dsa_switch internal structures.
Fixes: 0394a63acf ("net: dsa: enable and disable all ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it became possible for the DSA core to use a CPU port different
than 8, our bcm_sf2_imp_setup() function was broken because it assumes
that registers are applicable to port 8. In particular, the port's MAC
is going to stay disabled, so make sure we clear the RX_DIS and TX_DIS
bits if we are not configured for port 8.
Fixes: 9f91484f6f ("net: dsa: make "label" property optional for dsa2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NET_DSA_SMSC_LAN9303=y and NET_DSA_SMSC_LAN9303_MDIO=y,
below errors can be seen:
drivers/net/dsa/lan9303_mdio.c:87:23: error: REGMAP_ENDIAN_LITTLE
undeclared here (not in a function)
.reg_format_endian = REGMAP_ENDIAN_LITTLE,
drivers/net/dsa/lan9303_mdio.c:93:3: error: const struct regmap_config
has no member named reg_read
.reg_read = lan9303_mdio_read,
It should select REGMAP in config NET_DSA_SMSC_LAN9303.
Fixes: dc70058315 ("net: dsa: LAN9303: add MDIO managed mode support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier bugfix introduced a dependency on CONFIG_NET_SCH_TAPRIO,
but this missed the case of NET_SCH_TAPRIO=m and NET_DSA_SJA1105=y,
which still causes a link error:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x5c): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x3b4): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x6ec): undefined reference to `taprio_offload_free'
Change the dependency to only allow selecting the TAS code when it
can link against the taprio code.
Fixes: a8d570de0c ("net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS")
Fixes: 317ab5b86c ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the marvell switches have bits controlling the hash algorithm
the ATU uses for MAC addresses. In some industrial settings, where all
the devices are from the same manufacture, and hence use the same OUI,
the default hashing algorithm is not optimal. Allow the other
algorithms to be selected via devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leverage the recently add b53_mdb_{add,del,prepare} functions since they
work as-is for bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting IGMP snooping with or without the use of
a bridge, add support within b53_common.c to program the ARL entries for
multicast operations. The key difference is that a multicast ARL entry
is comprised of a bitmask of enabled ports, instead of a port number.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 0394a63acf ("net: dsa: enable and disable all ports")
the dsa core disables all unused ports of a switch. In this case
disabling ports with numbers higher than QCA8K_NUM_PORTS causes that
some switch registers are overwritten with incorrect content.
To fix this, initialize the dsa_switch->num_ports with correct number
of ports.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Like the dsa_switch_tree structures, the dsa_port structures will be
allocated on switch registration.
The SJA1105 driver is the only one accessing the dsa_port structure
after the switch allocation and before the switch registration.
For that reason, move switch registration prior to assigning the priv
member of the dsa_port structures.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list
of switch fabric ports to remap the Port VLAN Map of local bridge
group members or remap the Port VLAN Table entry of external bridge
group members.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list of
switch fabric ports to define the mask of the local ports allowed to
receive frames from another port of the fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Since mv88e6xxx_pvt_map is a static helper, no need to return
-EOPNOTSUPP if the chip has no PVT, simply silently skip the operation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Adjusting the hardware clock (PTPCLKVAL, PTPCLKADD, PTPCLKRATE) is a
requirement for the auxiliary PTP functionality of the switch
(TTEthernet, PPS input, PPS output).
Therefore we need to switch to using these registers to keep a
synchronized time in hardware, instead of the timecounter/cyclecounter
implementation, which is reliant on the free-running PTPTSCLK.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.
To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.
Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style
in header files related to Distributed Switch Architecture
drivers for NXP SJA1105 series Ethernet switch support.
It uses an expilict block comment for the SPDX License
Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style
in header files related to Distributed Switch Architecture
drivers for Microchip KSZ series switch support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reworks the SPI transfer implementation to make use of more of the
SPI core features. The main benefit is to avoid the memcpy in
sja1105_xfer_buf().
The memcpy was only needed because the function was transferring a
single buffer at a time. So it needed to copy the caller-provided buffer
at buf + 4, to store the SPI message header in the "headroom" area.
But the SPI core supports scatter-gather messages, comprised of multiple
transfers. We can actually use those to break apart every SPI message
into 2 transfers: one for the header and one for the actual payload.
To keep the behavior the same regarding the chip select signal, it is
necessary to tell the SPI core to de-assert the chip select after each
chunk. This was not needed before, because each spi_message contained
only 1 single transfer.
The meaning of the per-transfer cs_change=1 is:
- If the transfer is the last one of the message, keep CS asserted
- Otherwise, deassert CS
We need to deassert CS in the "otherwise" case, which was implicit
before.
Avoiding the memcpy creates yet another opportunity. The device can't
process more than 256 bytes of SPI payload at a time, so the
sja1105_xfer_long_buf() function used to exist, to split the larger
caller buffer into chunks.
But these chunks couldn't be used as scatter/gather buffers for
spi_message until now, because of that memcpy (we would have needed more
memory for each chunk). So we can now remove the sja1105_xfer_long_buf()
function and have a single implementation for long and short buffers.
Another benefit is lower usage of stack memory. Previously we had to
store 2 SPI buffers for each chunk. Due to the elimination of the
memcpy, we can now send pointers to the actual chunks from the
caller-supplied buffer to the SPI core.
Since the patch merges two functions into a rewritten implementation,
the function prototype was also changed, mainly for cosmetic consistency
with the structures used within it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that reduces some boilerplate in the SPI
interaction of the driver.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP command register contains enable bits for:
- Putting the 64-bit PTPCLKVAL register in add/subtract or write mode
- Taking timestamps off of the corrected vs free-running clock
- Starting/stopping the TTEthernet scheduling
- Starting/stopping PPS output
- Resetting the switch
When a command needs to be issued (e.g. "change the PTPCLKVAL from write
mode to add/subtract mode"), one cannot simply write to the command
register setting the PTPCLKADD bit to 1, because that would zeroize the
other settings. One also cannot do a read-modify-write (that would be
too easy for this hardware) because not all bits of the command register
are readable over SPI.
So this leaves us with the only option of keeping the value of the PTP
command register in the driver, and operating on that.
Actually there are 2 types of PTP operations now:
- Operations that modify the cached PTP command. These operate on
ptp_data->cmd as a pointer.
- Operations that apply all previously cached PTP settings, but don't
otherwise cache what they did themselves. The sja1105_ptp_reset
function is such an example. It copies the ptp_data->cmd on stack
before modifying and writing it to SPI.
This practically means that struct sja1105_ptp_cmd is no longer an
implementation detail, since it needs to be stored in full into struct
sja1105_ptp_data, and hence in struct sja1105_private. So the (*ptp_cmd)
function prototype can change and take struct sja1105_ptp_cmd as second
argument now.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a non-functional change with 2 goals (both for the case when
CONFIG_NET_DSA_SJA1105_PTP is not enabled):
- Reduce the size of the sja1105_private structure.
- Make the PTP code more self-contained.
Leaving priv->ptp_data.lock to be initialized in sja1105_main.c is not a
leftover: it will be used in a future patch "net: dsa: sja1105: Restore
PTP time after switch reset".
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new rule (as already started for sja1105_tas.h) is for functions of
optional driver components (ones which may be disabled via Kconfig - PTP
and TAS) to take struct dsa_switch *ds instead of struct sja1105_private
*priv as first argument.
This is so that forward-declarations of struct sja1105_private can be
avoided.
So make sja1105_ptp.h the second user of this rule.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need priv->ptp_caps to hold a structure and not just a pointer,
because we use container_of in the various PTP callbacks.
Therefore, the sja1105_ptp_caps structure declared in the global memory
of the driver serves no further purpose after copying it into
priv->ptp_caps.
So just populate priv->ptp_caps with the needed operations and remove
sja1105_ptp_caps.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the existing bitmask of mirrored ports essentially prevents us
from capturing more than one port at any given time. This is clearly
wrong, do not clear the bitmask prior to setting up the new port.
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Fixes: ed3af5fd08 ("net: dsa: b53: Add support for port mirroring")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/dsa/sja1105/sja1105_spi.c:159:5: warning: symbol 'sja1105_xfer_long_buf' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amazingly, of all features, this does not require a switch reset.
Tested with:
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress matchall skip_sw \
action mirred egress mirror dev swp3
tc filter show dev swp2 ingress
tc filter del dev swp2 ingress pref 49152
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most commonly called function in the driver is long due for a
rename. The "packed" word is redundant (it doesn't make sense to
transfer an unpacked structure, since that is in CPU endianness yadda
yadda), and the "spi" word is also redundant since argument 2 of the
function is SPI_READ or SPI_WRITE.
As for the sja1105_spi_send_long_packed_buf function, it is only being
used from sja1105_spi.c, so remove its global prototype.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a function that takes a variable number of unpacked bytes which
it generically calls an "int" is confusing and makes auditing patches
next to impossible.
We only use spi_send_int with the int sizes of 32 and 64 bits. So just
make the spi_send_int function less generic and replace it with the
appropriate two explicit functions, which can now type-check the int
pointer type.
Note that there is still a small weirdness in the u32 function, which
has to convert it to a u64 temporary. This is because of how the packing
API works at the moment, but the weirdness is at least hidden from
callers of sja1105_xfer_u32 now.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this stack trace can be seen with CONFIG_DEBUG_ATOMIC_SLEEP=y:
[ 41.568348] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:909
[ 41.576757] in_atomic(): 1, irqs_disabled(): 0, pid: 208, name: ptp4l
[ 41.583212] INFO: lockdep is turned off.
[ 41.587123] CPU: 1 PID: 208 Comm: ptp4l Not tainted 5.3.0-rc6-01445-ge950f2d4bc7f-dirty #1827
[ 41.599873] [<c0313d7c>] (unwind_backtrace) from [<c030e13c>] (show_stack+0x10/0x14)
[ 41.607584] [<c030e13c>] (show_stack) from [<c1212d50>] (dump_stack+0xd4/0x100)
[ 41.614863] [<c1212d50>] (dump_stack) from [<c037dfc8>] (___might_sleep+0x1c8/0x2b4)
[ 41.622574] [<c037dfc8>] (___might_sleep) from [<c122ea90>] (__mutex_lock+0x48/0xab8)
[ 41.630368] [<c122ea90>] (__mutex_lock) from [<c122f51c>] (mutex_lock_nested+0x1c/0x24)
[ 41.638340] [<c122f51c>] (mutex_lock_nested) from [<c0c6fe08>] (sja1105_static_config_reload+0x30/0x27c)
[ 41.647779] [<c0c6fe08>] (sja1105_static_config_reload) from [<c0c7015c>] (sja1105_hwtstamp_set+0x108/0x1cc)
[ 41.657562] [<c0c7015c>] (sja1105_hwtstamp_set) from [<c0feb650>] (dev_ifsioc+0x18c/0x330)
[ 41.665788] [<c0feb650>] (dev_ifsioc) from [<c0febbd8>] (dev_ioctl+0x320/0x6e8)
[ 41.673064] [<c0febbd8>] (dev_ioctl) from [<c0f8b1f4>] (sock_ioctl+0x334/0x5e8)
[ 41.680340] [<c0f8b1f4>] (sock_ioctl) from [<c05404a8>] (do_vfs_ioctl+0xb0/0xa10)
[ 41.687789] [<c05404a8>] (do_vfs_ioctl) from [<c0540e3c>] (ksys_ioctl+0x34/0x58)
[ 41.695151] [<c0540e3c>] (ksys_ioctl) from [<c0301000>] (ret_fast_syscall+0x0/0x28)
[ 41.702768] Exception stack(0xe8495fa8 to 0xe8495ff0)
[ 41.707796] 5fa0: beff4a8c 00000001 00000011 000089b0 beff4a8c beff4a80
[ 41.715933] 5fc0: beff4a8c 00000001 0000000c 00000036 b6fa98c8 004e19c1 00000001 00000000
[ 41.724069] 5fe0: 004dcedc beff4a6c 004c0738 b6e7af4c
[ 41.729860] BUG: scheduling while atomic: ptp4l/208/0x00000002
[ 41.735682] INFO: lockdep is turned off.
Enabling RX timestamping will logically disturb the fastpath (processing
of meta frames). Replace bool hwts_rx_en with a bit that is checked
atomically from the fastpath and temporarily unset from the sleepable
context during a change of the RX timestamping process (a destructive
operation anyways, requires switch reset).
If found unset, the fastpath (net/dsa/tag_sja1105.c) will just drop any
received meta frame and not take the meta_lock at all.
Fixes: a602afd200 ("net: dsa: sja1105: Expose PTP timestamping ioctls to userspace")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been some confusion between the port number and
the VLAN ID in this driver. What we need to check for
validity is the VLAN ID, nothing else.
The current confusion came from assigning a few default
VLANs for default routing and we need to rewrite that
properly.
Instead of checking if the port number is a valid VLAN
ID, check the actual VLAN IDs passed in to the callback
one by one as expected.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_get_child_by_name finished using.
irq_domain_add_linear() also calls of_node_get() to increase refcount,
so irq_domain will not be affected when it is released.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sja1105_static_config_upload, in two cases memory is leaked: when
static_config_buf_prepare_for_upload fails and when sja1105_inhibit_tx
fails. In both cases config_buf should be released.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Fixes: 1a4c69406c ("net: dsa: sja1105: Prevent PHY jabbering during switch reset")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the PTP synchronization on the switch 'jumps':
ptp4l[11241.155]: rms 8 max 16 freq -21732 +/- 11 delay 742 +/- 0
ptp4l[11243.157]: rms 7 max 17 freq -21731 +/- 10 delay 744 +/- 0
ptp4l[11245.160]: rms 33592410 max 134217731 freq +192422 +/- 8530253 delay 743 +/- 0
ptp4l[11247.163]: rms 811631 max 964131 freq +10326 +/- 557785 delay 743 +/- 0
ptp4l[11249.166]: rms 261936 max 533876 freq -304323 +/- 126371 delay 744 +/- 0
ptp4l[11251.169]: rms 48700 max 57740 freq -20218 +/- 30532 delay 744 +/- 0
ptp4l[11253.171]: rms 14570 max 30163 freq -5568 +/- 7563 delay 742 +/- 0
ptp4l[11255.174]: rms 2914 max 3440 freq -22001 +/- 1667 delay 744 +/- 1
ptp4l[11257.177]: rms 811 max 1710 freq -22653 +/- 451 delay 744 +/- 1
ptp4l[11259.180]: rms 177 max 218 freq -21695 +/- 89 delay 741 +/- 0
ptp4l[11261.182]: rms 45 max 92 freq -21677 +/- 32 delay 742 +/- 0
ptp4l[11263.186]: rms 14 max 32 freq -21733 +/- 11 delay 742 +/- 0
ptp4l[11265.188]: rms 9 max 14 freq -21725 +/- 12 delay 742 +/- 0
ptp4l[11267.191]: rms 9 max 16 freq -21727 +/- 13 delay 742 +/- 0
ptp4l[11269.194]: rms 6 max 15 freq -21726 +/- 9 delay 743 +/- 0
ptp4l[11271.197]: rms 8 max 15 freq -21728 +/- 11 delay 743 +/- 0
ptp4l[11273.200]: rms 6 max 12 freq -21727 +/- 8 delay 743 +/- 0
ptp4l[11275.202]: rms 9 max 17 freq -21720 +/- 11 delay 742 +/- 0
ptp4l[11277.205]: rms 9 max 18 freq -21725 +/- 12 delay 742 +/- 0
Background: the switch only offers partial RX timestamps (24 bits) and
it is up to the driver to read the PTP clock to fill those timestamps up
to 64 bits. But the PTP clock readout needs to happen quickly enough (in
0.135 seconds, in fact), otherwise the PTP clock will wrap around 24
bits, condition which cannot be detected.
Looking at the 'max 134217731' value on output line 3, one can see that
in hex it is 0x8000003. Because the PTP clock resolution is 8 ns,
that means 0x1000000 in ticks, which is exactly 2^24. So indeed this is
a PTP clock wraparound, but the reason might be surprising.
What is going on is that sja1105_tstamp_reconstruct(priv, now, ts)
expects a "now" time that is later than the "ts" was snapshotted at.
This, of course, is obvious: we read the PTP time _after_ the partial RX
timestamp was received. However, the workqueue is processing frames from
a skb queue and reuses the same PTP time, read once at the beginning.
Normally the skb queue only contains one frame and all goes well. But
when the skb queue contains two frames, the second frame that gets
dequeued might have been partially timestamped by the RX MAC _after_ we
had read our PTP time initially.
The code was originally like that due to concerns that SPI access for
PTP time readout is a slow process, and we are time-constrained anyway
(aka: premature optimization). But some timing analysis reveals that the
time spent until the RX timestamp is completely reconstructed is 1 order
of magnitude lower than the 0.135 s deadline even under worst-case
conditions. So we can afford to read the PTP time for each frame in the
RX timestamping queue, which of course ensures that the full PTP time is
in the partial timestamp's future.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QCA8K family supports up to 7 ports. So use the existing
QCA8K_NUM_PORTS define to allocate the switch structure and limit all
operations with the switch ports.
This was not an issue until commit 0394a63acf ("net: dsa: enable and
disable all ports") disabled all unused ports. Since the unused ports 7-11
are outside of the correct register range on this switch some registers
were rewritten with invalid content.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Fixes: a0c02161ec ("net: dsa: variable number of ports")
Fixes: 0394a63acf ("net: dsa: enable and disable all ports")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The regmap stride is set to 1 for regmap describing 8bit registers already.
However, for 16/32/64bit registers, the stride is 2/4/8 respectively. This
is not correct, as the switch protocol supports unaligned register reads
and writes and the KSZ87xx even uses such unaligned register accesses to
read e.g. MIB counter.
This patch fixes MIB counter access on KSZ87xx.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Fixes: 46558d601c ("net: dsa: microchip: Initial SPI regmap support")
Fixes: 255b59ad0d ("net: dsa: microchip: Factor out regmap config generation into common header")
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port does not have a PHY connected to it. So calling
phy_support_asym_pause() results in an Opps. As with other DSA
drivers, add a guard that the port is a user port.
Reported-by: Michal Vokáč <michal.vokac@ysoft.com>
Fixes: 0394a63acf ("net: dsa: enable and disable all ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style
in header file for Distributed Switch Architecture drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch corrects the SPDX License Identifier style
in header file for Broadcom BCM53xx managed switch driver.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If CONFIG_NET_DSA_SJA1105_TAS=y and CONFIG_NET_SCH_TAPRIO=n,
below error can be found:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x318): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x590): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x610): undefined reference to `taprio_offload_free'
make: *** [vmlinux] Error 1
sja1105_tas needs tc-taprio, so this patch add the dependency for it.
Fixes: 317ab5b86c ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This qdisc offload is the closest thing to what the SJA1105 supports in
hardware for time-based egress shaping. The switch core really is built
around SAE AS6802/TTEthernet (a TTTech standard) but can be made to
operate similarly to IEEE 802.1Qbv with some constraints:
- The gate control list is a global list for all ports. There are 8
execution threads that iterate through this global list in parallel.
I don't know why 8, there are only 4 front-panel ports.
- Care must be taken by the user to make sure that two execution threads
never get to execute a GCL entry simultaneously. I created a O(n^4)
checker for this hardware limitation, prior to accepting a taprio
offload configuration as valid.
- The spec says that if a GCL entry's interval is shorter than the frame
length, you shouldn't send it (and end up in head-of-line blocking).
Well, this switch does anyway.
- The switch has no concept of ADMIN and OPER configurations. Because
it's so simple, the TAS settings are loaded through the static config
tables interface, so there isn't even place for any discussion about
'graceful switchover between ADMIN and OPER'. You just reset the
switch and upload a new OPER config.
- The switch accepts multiple time sources for the gate events. Right
now I am using the standalone clock source as opposed to PTP. So the
base time parameter doesn't really do much. Support for the PTP clock
source will be added in a future series.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation patch for the tc-taprio offload (and potentially
for other future offloads such as tc-mqprio).
Instead of looking directly at skb->priority during xmit, let's get the
netdev queue and the queue-to-traffic-class mapping, and put the
resulting traffic class into the dsa_8021q PCP field. The switch is
configured with a 1-to-1 PCP-to-ingress-queue-to-egress-queue mapping
(see vlan_pmap in sja1105_main.c), so the effect is that we can inject
into a front-panel's egress traffic class through VLAN tagging from
Linux, completely transparently.
Unfortunately the switch doesn't look at the VLAN PCP in the case of
management traffic to/from the CPU (link-local frames at
01-80-C2-xx-xx-xx or 01-1B-19-xx-xx-xx) so we can't alter the
transmission queue of this type of traffic on a frame-by-frame basis. It
is only selected through the "hostprio" setting which ATM is harcoded in
the driver to 7.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support tc-taprio offload, the TTEthernet egress scheduling
core registers must be made visible through the static interface.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the per-port egress flooding control for
both Unicast and Multicast traffic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9567 7-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9567 supports both SPI and I2C. Oddly the
ksz9567 is already in the device tree binding documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9477 I2C driver support. The code ksz9477.c and ksz_common.c are
used together to generate the I2C driver.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
[george.mccollister@gmail.com: bring up to date, use ksz_common regmap macros]
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean