It seems by default the VBT has MIPI configuration block as well. The
Generic driver will assume always MIPI if MIPI configuration block is found.
This is causing probelm when actually there is eDP. Fix this by looking
into general definition block which will have device configurations. From here
we can figure out what is the LFP type and initialize MIPI only if MIPI
is found.
v2: Addressed review comments by Damien
- Moved PORT definitions to intel_bios.h and renamed as DVO_PORT_MIPIA
- renamed is_mipi to has_mipi and moved definition as suggested
- Check has_mipi inside parse_mipi and intel_dsi_init insted of outside
v3: Make has_mipi as a bitfield as suggested
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: fold in conditions to pack everything neatly below 80 chars.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Be we read and chase pointers from the VBT, it is prudent to make sure
that those accesses are wholly contained within the MMIO region, or else
we may cause a kernel panic during boot.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure that the whole BDB section is within the MMIO region prior to
accessing it contents. That we don't read outside of the secion is left
up to the individual section parsers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
This cleans up the checkpatch errors for the merged commit -
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The parser extracts the config block(#52) and sequence(#53) data
and store in private data structures.
v2: Address review comments by Jani
- adjust code for the structure changes for bdb_mipi_config
- add boundry and buffer overflow checks as suggested
- use kmemdup instead of kmalloc and memcpy
v3: More strict check while parsing VBT
- Ensure that at anytime we do not go beyond sequence block
while parsing
- On unknown element fail the whole parsing
v4: Style changes and spell check mostly as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only supported types are none and PWM. Other values are obsolete or
reserved, don't add them.
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch reads the DRRS support and Mode type from VBT fields.
The read information will be stored in VBT struct during BIOS
parsing. The above functionality is needed for decision making
whether DRRS feature is supported in i915 driver for eDP panels.
This information helps us decide if seamless DRRS can be done
at runtime to support certain power saving features. This patch
was tested by setting necessary bit in VBT struct and merging
the new VBT with system BIOS so that we can read the value.
v2: Incorporated review comments from Chris Wilson
Removed "intel_" as a prefix for DRRS specific declarations.
v3: Incorporated Jani's review comments
Removed function which deducts drrs mode from panel_type. Modified some
print statements. Made changes to use DRRS_NOT_SUPPORTED as 0 instead of -1.
v4: Incorporated Jani's review comments.
Modifications around setting vbt drrs_type.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
[danvet: Drop the misleading/redundant comment about the added drrs
field in the vbt struct as discussed with Jani on irc.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MIPI Block #52 which provides configuration details for the MIPI panel
including dphy settings as per panel and tcon specs
Block #53 gives information on panel enable sequences
v2: Address review comemnts from Jani
- Move panel ids from intel_dsi.h to intel_bios.h
- bdb_mipi_config structure improvements for cleaner code
- Adding units for the pps delays, all in ms
- change data structure to be more cleaner and simple
v3: Corrected the unit for pps delays as 100us
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.
Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".
The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:
$ git grep "i915\." -- drivers/gpu/drm/i915
v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't actually do anything with the information yet, but parse and
log what's in the VBT.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store the SSC refclock frequency in kHz to get more accuracy. Currently
we're pretending that 66 MHz is ~66000 kHz, when in fact it is actually
~66667 kHz. By storing the less rounded kHz value we get a much better
accuracy for out pixel clock calculations.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had been using a DMI table workaround to select the right
frequency for devices, but this is fragile and must be updated
with every new platform.
Instead the default case when VBT is missing is changed to use
120MHz clock for LVDS SSC for these generations.
The docs for 2010-Core, SandyBridge, and IvyBridge all indicate
that the reference frequency for LVDS is 120MHz:
"2010 Core"
http://intellinuxgraphics.org/IHD_OS_Vol3_Part3r2.pdf
page 38
Reference Frequency: 120MHz for CRT and LVDS. 100MHz for the FDI.
"2011 SandyBridge"
http://intellinuxgraphics.org/documentation/SNB/IHD_OS_Vol3_Part3.pdf
page 33
Reference Frequency: 120MHz for CRT, HDMI, LVDS. 100MHz for the FDI.
"2012 IvyBridge"
http://intellinuxgraphics.org/documentation/IVB/IHD_OS_Vol3_Part4.pdf
page 27
Reference Frequency: 120 MHz for CRT, HDMI, LVDS, 100MHz for the FDI.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
[olof: Fixup for recent base, switched from if/else to single call]
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It only controls the setting of the vbt.edp_support variable, which in
turn only controls one debug output plus can also force-disable the
lvds output.
Since the value only restricted this logic to mobile ilk there's the
slight risk that this will break lvds on desktop ilk or on snb/ivb
platforms. But with the vbt it's better when we know what's going on
here, so let's rip it out and see what happens.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no reason to init a DP connector if the encoder just supports
HDMI: we'll just waste hundreds and hundreds of cycles trying to do DP
AUX transactions to detect if there's something there. Same goes for a
DP connector that doesn't support HDMI, but I'm not sure these
actually exist.
v2: - Use bit fields
- Remove useless identation level
- Replace DRM_ERROR with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our code makes a lot of assumptions regarding what each DDI port
actually supports, and the VBT should tell us what is really happening
in the hardware. So parse the information provided by the VBT and
check if any of our assumptions is wrong.
Our driver also has a history of not really trusting the VBT, so a
WARN here could mean that:
a) our coding assumptions are wrong
b) the VBT is wrong
c) we're incorrectly parsing the VBT
d) the checks are wrong
But I really hope we won't ever trigger any of those WARNs.
v2: Don't check the redundant "Capabilities" field from byte 24 since
it doesn't seem to be used.
v3: Rebase
v4: Replace WARN with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our code currently assumes that port X will use the DP AUX channel X
and the DDC pin X. The VBT should tell us how things are mapped, so
add some WARNs in case we discover our assumptions are wrong (or in
case the VBT is just wrong, which is also perfectly possible).
Why would someone wire port B to AUX C and DDC D?
v2: Rebase
v3: Convert WARNs to DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently use the recommended values from BSpec, but the VBT
specifies the correct value to use for the hardware we have, so use
it. We also fall back to the recommended value in case we can't find
the VBT.
In addition, this code also provides some infrastructure to parse more
information about the DDI ports. There's a lot more information we
could extract and use in the future.
v2: - Move some code to init_vbt_defaults.
v3: - Rebase
- Clarify the "DVO Port" matching code
v4: - Use I915_MAX_PORTS
- Change the HAS_DDI checks
- Replace DRM_ERROR with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently treat the child_device_config as a simple struct, but
this is not correct: new BDB versions change the meaning of some
offsets, so the struct needs to be adjusted for each version.
Since there are too many changes (today we're in version 170!), making
a big versioned union would be too complicated, so child_device_config
is now a union of 3 things: (i) a "raw" byte array that's safe to use
anywhere; (ii) an "old" structure that's the one we've been using and
should be safe to keep in the SDVO and TV code; and (iii) a "common"
structure that should contain only fields that are common for all the
known VBT versions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Initial parsing of the VBT MIPI block. For now, just store the panel id
if found.
Note: Again there seems to be no documentation for this piece of lore.
The doc situation for byt+ is just a bad joke :(
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_i915_private is getting bigger and bigger when adding new vbt stuff.
So, the better way of getting drm_i915_private organized is to create
a special structure for vbt stuff.
v2: Basically conflicts fixes
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the VBT to see if the machine has inverted FDI RX polarity on
CPT. Based on this bit, set the appropriate bit on the TRANS_CHICKEN2
registers.
This should fix some machines that were showing black screens on all
outputs.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60029
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Interrupts, clock gating, LVDS, and GMBUS are all within the, "this will
be bad for CPU" range when we have PCH_NOP.
There is a bit of a hack in init clock gating. We want to do most of the
clock gating, but the part we skip will hang the system. It could
probably be abstracted a bit better, but I don't feel it's too
unsightly.
v2: Use inverse HAS_PCH_NOP check (Jani)
v3: Actually do what I claimed in v2 (spotted by Daniel)
Merge Ivybridge IRQ handler PCH check to decrease whitespace (Daniel)
Move LVDS bail into this patch (Ben)
v4: logical rebase conflict resolution with SDEIIR (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Brush up patch a bit and resolve conflicts:
- Adjust PCH_NOP checks due to Egbert's hpd handling rework.
- Addd a PCH_NOP check in the irq uninstall code.
- Resolve conflicts with Paulo's SDE irq handling race fix.
v5: Drop the added hunks in the ilk irq handler again, they're bogus.
OOps.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alex writes:
Pretty minor -next pull request. We some additional new bits waiting
internally for release. Hopefully Monday we can get at least some of
them out. The others will probably take a few more weeks.
Highlights of the current request:
- ELD registers for passing audio information to the sound hardware
- Handle GPUVM page faults more gracefully
- Misc fixes
Merge radeon test
* 'drm-next-3.8' of git://people.freedesktop.org/~agd5f/linux: (483 commits)
drm/radeon: bump driver version for new info ioctl requests
drm/radeon: fix eDP clk and lane setup for scaled modes
drm/radeon: add new INFO ioctl requests
drm/radeon/dce32+: use fractional fb dividers for high clocks
drm/radeon: use cached memory when evicting for vram on non agp
drm/radeon: add a CS flag END_OF_FRAME
drm/radeon: stop page faults from hanging the system (v2)
drm/radeon/dce4/5: add registers for ELD handling
drm/radeon/dce3.2: add registers for ELD handling
radeon: fix pll/ctrc mapping on dce2 and dce3 hardware
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
Revert "drm/i915: enable rc6 on ilk again"
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
...
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_encoder.c
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/core/engine/disp/nv50.c
commit 500a8cc466
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Wed Jan 13 11:19:52 2010 +0800
drm/i915: parse eDP panel color depth from VBT block
originally introduced parsing bpp for eDP from VBT, with a default of 18
bpp if the eDP BIOS data block is not present. Turns out that default seems
to break the Macbook Pro with retina display, as noted in
commit 4344b813f1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Aug 10 11:10:20 2012 +0200
drm/i915: ignore eDP bpc settings from vbt
Since we can't ignore bpc settings from VBT completely after all, get rid
of the default. Do not clamp eDP to 18 bpp by default if the eDP BDB is
missing from VBT.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
[danvet: paste in the updated commit message from irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK+ have this register on the PCH. This check was triggering unclaimed
writes.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h). They are now #included via drmP.h and drm_crtc.h via a preceding
patch.
Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..." work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
These are unintuitive. These are type bool and return -1 casted to true
on failure. Let's just make it return an int. The callers don't care,
but let's change this as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
ids are not yet added, and there's still quite a few patches to merge
(mostly modesetting). To make QA easier I've decided to merge this stuff
in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
is a real frankenstein chip, but also hsw is stretching our driver's
code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
there are more patches needed (and some already queued up), but I wanted
to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
a few months already and a lot of i-g-t tests have been created for it.
Now it's finally ready to be merged. Note that one patch in this series
touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
driver we actually need to support by bailing out of unsupported case.
The driver now refuses to load without kms on gen6+ and disallows a few
ioctls that userspace never used in certain cases. More of this will
definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
in this way).
- Small fixlets and adjustements and some minor things to help debugging.
Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
drm/i915: VCS is not the last ring
drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
drm/i915: make quirks more verbose
drm/i915: dump the DMA fetch addr register on pre-gen6
drm/i915/sdvo: Include YRPB as an additional TV output type
drm/i915: disallow gem init ioctl on ilk
drm/i915: refuse to load on gen6+ without kms
drm/i915: extract gt interrupt handler
drm/i915: use render gen to switch ring irq functions
drm/i915: rip out old HWSTAM missed irq WA for vlv
drm/i915: open code gen6+ ring irqs
drm/i915: ring irq cleanups
drm/i915: add SFUSE_STRAP registers for digital port detection
drm/i915: add WM_LINETIME registers
drm/i915: add WRPLL clocks
drm/i915: add LCPLL control registers
drm/i915: add SSC offsets for SBI access
drm/i915: add port clock selection support for HSW
drm/i915: add S PLL control
drm/i915: add PIXCLK_GATE register
...
Conflicts:
drivers/char/agp/intel-agp.h
drivers/char/agp/intel-gtt.c
drivers/gpu/drm/i915/i915_debugfs.c
Somehow the BIOS manages to screw things up when copying the VBT
around, because the one we scrap from the VBIOS rom actually works.
Cc: stable@kernel.org
Tested-by: Markus Heinz <markus.heinz@uni-dortmund.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28812
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of letting other modules directly access the ->gmbus array,
introduce intel_gmbus_get_adapter() for looking up an i2c_adapter
for a given gmbus port identifier. This will enable later refactoring
of the gmbus port list.
Note: Before requesting an adapter for a given gmbus port number, the
driver must first check its validity using i2c_intel_gmbus_is_port_valid().
If this check fails, a call to intel_gmbus_get_adapter() will WARN_ON and
return NULL. This is relevant for parts of the driver that read a port
from VBIOS, which might be improperly initialized and contain an invalid
port. In these cases, the driver must fall back to using a safer default
port.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently i915 driver checks [PCH_]LVDS register bits to decide
whether to set up the dual-link or the single-link mode. This relies
implicitly on that BIOS initializes the register properly at boot.
However, BIOS doesn't initialize it always. When the machine is
booted with the closed lid, BIOS skips the LVDS reg initialization.
This ends up in blank output on a machine with a dual-link LVDS when
you open the lid after the boot.
This patch adds a workaround for that problem by checking the initial
LVDS register value in VBT.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=37742
Tested-By: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This change enables the use of displays where the vbt table just
contains inappropriate values, but either the vesa defaults or
the video=... modes do something sensible with the attached display.
The problem happens with an embedded board that contains vbt bios
tables that do not match the attached display. Using this change and
the appropriate kernel boot command line they are able to use an
otherwise completely unusable secondary display on that embedded
board.
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Mathias Froehlich <Mathias.Froehlich@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we warn the user later that we cannot find or load the VBIOS,
explaining why is an exercise in debugging. Shouting *ERROR* upsets
people and produces bug reports.
Reported-by: Michael Rieder <mr@student.ethz.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43751
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I have no evidence for this byte being used this way, and lots of
counterexamples. Restore the struct to its empirical definition and
patch up gmbus setup to match.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This tells the driver whether a CK505 clock source is available on
pre-PCH hardware. If so, it should be used as the non-SSC source,
leaving the internal clock for use as the SSC source.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wison <chris@chris-wilson.co.uk>
These are all KMS related anyways, so don't hide them under other
debug levels.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Alan Cox reported a missing check on the kmalloc return value for the
allocation of a temporary mode used for searching for the LVDS downlock
frequency. This allocation is roughly 200 bytes, a little too large to
friviously place on the stack. However, we can simply use the few bytes
we need stored within the original DVO timing data, skip the translation
and do the compare directly between the timing data rather than on a
mode, thus avoiding the need for any temporary allocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add __attribute__((format (printf, 4, 5))) to drm_ut_debug_printk
and fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 633f2ea266 and the
attempted fix dcbe6f2b3d.
There is a single clock source used for both SSC (some LVDS and DP) and
non-SSC (VGA, DVI) outputs. So we need to be careful to only enable SSC
as necessary. However, fiddling with DREFCLK was causing DP links to be
dropped and we do not have a fix ready, so revert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Judging by comments in the BIOS, if the SDVO LVDS option h40 is enabled,
then we are supposed to query the real panel type via Int15. We don't do
this and so for the Sony Vaio VGC-JS210J which has otherwise default
values, we choose the wrong mode.
This patch adds a driver option, i915.vbt_sdvo_panel_type, which can be
used to override the value in the VBT.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33691
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
For CRT and SDVO/HDMI, we need to use a normal, non-SSC, clock and so we
must clear any enabling bits left-over from earlier outputs. And also
seems to correct the LVDS panel on the Lenovo U160.
However, at one point, it did cause an "ERROR failed to disable
trancoder". So prolonged testing on top of Jesse's refactored and
error-checking CRTC logic is desired.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The i915 driver normally assumes the video bios has configured several
of the LVDS panel registers, and it just inherits the values. If the
vbios has not run, several of these will need to be setup.
If these are not correct then although the panel looks ok, output from an
HDMI encoder (eg, Chrontel CH7036) will be incorrect.
Signed-off-by: Mark Hayter <mdhayter@chromium.org>
[ickle: minor adjustments]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to workaround the issue with LVDS not working on the Lenovo
U160 apparently due to using the wrong SSC frequency, add an option to
disable SSC.
Suggested-by: Lukács, Árpád <lukacs.arpad@gmail.com>
Bugzillla: https://bugs.freedesktop.org/show_bug.cgi?id=32748
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Shobhit Kumar