The ETM state save/restore incorrectly reads/writes some of the 64bit
registers (e.g, address comparators, vmid/cid comparators etc.) using
32bit accesses. Ensure we use the appropriate width accessors for
the registers.
Fixes: f188b5e76a ("coresight: etm4x: Save/restore state across CPU low power states")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200716175746.3338735-18-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETMv4 max resource selector constant incorrectly set to 16. Updated to the
correct 32 value, and adjustments made to limited code using it.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Fixes: 2e1cdfe184 ("coresight-etm4x: Adding CoreSight ETM4x driver")
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200716175746.3338735-10-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Qualcomm Technologies Inc. SoCs like SC7180, there
exists a hardware errata where the APSS (Application Processor
SubSystem)/CPU watchdog counter is stopped when the trace unit
power up ETM register is set (TRCPDCR.PU = 1). Since the ETMs
share the same power domain as that of respective CPU cores,
they are powered on when the CPU core is powered on. So we can
skip powering up of trace unit after checking for this errata
via new property called "qcom,skip-power-up".
Signed-off-by: Tingwei Zhang <tingwei@codeaurora.org>
Co-developed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200716175746.3338735-4-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An API to control single-shot comparator operation was missing from sysfs.
This adds the parameters to sysfs to allow programming of this feature.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20191104181251.26732-12-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETMv4.4 adds in support for tracing secure EL2 (per arch 8.x updates).
Patch accounts for this new capability.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20191104181251.26732-5-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some hardware will ignore bit TRCPDCR.PU which is used to signal
to hardware that power should not be removed from the trace unit.
Let's mitigate against this by conditionally saving and restoring
the trace unit state when the CPU enters low power states.
This patchset introduces a firmware property named
'arm,coresight-loses-context-with-cpu' - when this is present the
hardware state will be conditionally saved and restored.
A module parameter 'pm_save_enable' is also introduced which can
be configured to override the firmware property. This can be set
to never allow save/restore or to conditionally allow it (only for
self-hosted). The default value is determined by firmware.
We avoid saving the hardware state when self-hosted coresight isn't
in use to reduce PM latency - we can't determine this by reading the
claim tags (TRCCLAIMCLR) as these are 'trace' registers which need
power and clocking, something we can't easily provide in the PM
context. Therefore we rely on the existing drvdata->mode internal
state that is set when self-hosted coresight is used (and powered).
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20191104181251.26732-2-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Track the coresight device instead of the real device.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with ETM3x, the ETM4x tracers can trigger trace acquisition based on
contextID value, something that isn't useful when PID namespaces are
enabled. Indeed the PID value of a process has a different representation
in the kernel and the PID namespace, making the feature confusing and
potentially leaking internal kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using perf record 'cyclacc' option in cs_etm event was not setting up cycle
accurate trace correctly.
Corrects bit set in TRCCONFIGR to enable cycle accurate trace.
Programs TRCCCCTLR with a valid threshold value as required by ETMv4 spec.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both ETMv3 and ETMv4 drivers are declaring an 'enum etm_addr_type',
creating reduncancy.
This patch removes the enumeration from the driver files and adds
it to a common header.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Coresight ETMv4 architecture provides a way to request to keep the
power to the trace unit. This might help to collect the traces without
the need to disable the CPU power management(entering/exiting deeper
idle states).
Trace PowerDown Control Register provides powerup request bit which when
set requests the system to retain power to the trace unit and emulate
the powerdown request.
Typically, a trace unit drives a signal to the power controller to
request that the trace unit core power domain is powered up. However,
if the trace unit and the CPU are in the same power domain then the
implementation might combine the trace unit power up status with a
signal from the CPU.
This patch requests to retain power to the trace unit when active and
to remove when inactive. Note this change will only request but the
behaviour depends on the implementation. However, it matches the
exact behaviour expected when the external debugger is connected with
respect to CPU power states.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because this operation exceed the range of boolean,
so we should modify q_support to unit8 bit.
drvdata->q_support = BMVAL(etmidr0, 15, 16)
Signed-off-by: Li Pengcheng <lipengcheng8@huawei.com>
Signed-off-by: Li Zhong <lizhong11@hisilicon.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding new mode to limit tracing to kernel or user space.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly to ETMv3, moving etmv4_drvdata::enable to an atomic
type that gives the 'mode' of a tracer and prevents multiple,
simultanious access by different subsystems.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Splitting and updating the default initialisation for each etmv4
configuration so that it can be called at the beginning of each
session rather than initialisation time only.
Since the trace ID isn't expected to change with every session,
moving it with the default tracer initialisation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to what was done on etm3x, splitting driver structure
etmv4_drvdata in two. One half is concerned with the HW
characteristics that are generally static in nature. The other
half deals with user configuration and will change from one
trace session to another.
No gain/loss of functionality is incurred from this patch.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with the etm3x driver, sysFS entries are big enough to justify
their own file. As such moving all sysFS related declarations to
a dedicated location.
No gain/loss of functionality is incurred from this patch.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like ETTv3, ETMv4 also needs the similar modifications to support Context
ID tracing when PID namespace is enabled.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ctxid_val' array was used to store the value of ETM context ID comparator
which actually stores the process ID to be traced, so using 'ctxid_pid' as
its name instead make it easier to understand.
This patch also changes the ABI, it is normally not allowed, but
fortunately it is a testing ABI and very new for now. Nevertheless,
if you don't think it should be changed, we could always add an alias
for userspace.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose