TCP is going to record metrics for the connection,
so pre-COW the route metrics at route cache entry
creation time.
This avoids several atomic operations that have to
occur if we COW the metrics after the entry reaches
global visibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing metrics are now copy-on-write.
Initially a route entry points it's metrics at a read-only location.
If a routing table entry exists, it will point there. Else it will
point at the all zero metric place-holder called 'dst_default_metrics'.
The writeability state of the metrics is stored in the low bits of the
metrics pointer, we have two bits left to spare if we want to store
more states.
For the initial implementation, COW is implemented simply via kmalloc.
However future enhancements will change this to place the writable
metrics somewhere else, in order to increase sharing. Very likely
this "somewhere else" will be the inetpeer cache.
Note also that this means that metrics updates may transiently fail
if we cannot COW the metrics successfully.
But even by itself, this patch should decrease memory usage and
increase cache locality especially for routing workloads. In those
cases the read-only metric copies stay in place and never get written
to.
TCP workloads where metrics get updated, and those rare cases where
PMTU triggers occur, will take a very slight performance hit. But
that hit will be alleviated when the long-term writable metrics
move to a more sharable location.
Since the metrics storage went from a u32 array of RTAX_MAX entries to
what is essentially a pointer, some retooling of the dst_entry layout
was necessary.
Most importantly, we need to preserve the alignment of the reference
count so that it doesn't share cache lines with the read-mostly state,
as per Eric Dumazet's alignment assertion checks.
The only non-trivial bit here is the move of the 'flags' member into
the writeable cacheline. This is OK since we are always accessing the
flags around the same moment when we made a modification to the
reference count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Flush the routing cache only of entries that match the
network namespace in which the purge event occurred.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we test rt->fl.iif against zero, we're seeing if it's
an output or an input route.
Make that explicit with some helper functions.
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems idev field in struct rtable has no special purpose, but adding
extra atomic ops.
We hold refcounts on the device itself (using percpu data, so pretty
cheap in current kernel).
infiniband case is solved using dst.dev instead of idev->dev
Removal of this field means routing without route cache is now using
shared data, percpu data, and only potential contention is a pair of
atomic ops on struct neighbour per forwarded packet.
About 5% speedup on routing test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() is the version returning a refcounted dst, while
ip_route_input_noref() returns a non refcounted one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __percpu sparse annotations to net.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
The macro and type tricks around snmp stats make things a bit
interesting. DEFINE/DECLARE_SNMP_STAT() macros mark the target field
as __percpu and SNMP_UPD_PO_STATS() macro is updated accordingly. All
snmp_mib_*() users which used to cast the argument to (void **) are
updated to cast it to (void __percpu **).
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The motivation for an additional notifier in batched netdevice
notification (rt_do_flush) only needs to be called once per batch not
once per namespace.
For further batching improvements I need a guarantee that the
netdevices are unregistered in order allowing me to unregister an all
of the network devices in a network namespace at the same time with
the guarantee that the loopback device is really and truly
unregistered last.
Additionally it appears that we moved the route cache flush after
the final synchronize_net, which seems wrong and there was no
explanation. So I have restored the original location of the final
synchronize_net.
Cc: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleanup patch puts struct/union/enum opening braces,
in first line to ease grep games.
struct something
{
becomes :
struct something {
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set FLOWI_FLAG_ANYSRC in flowi->flags if the socket has the
transparent socket option set. This way we selectively enable certain
connections with non-local source addresses to be routed.
Signed-off-by: KOVACS Krisztian <hidden@sch.bme.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_iif() in inet_sock.h requires route.h. Since users of inet_iif()
usually require other route.h functionality anyway this patch moves
inet_iif() to route.h.
Signed-off-by: KOVACS Krisztian <hidden@sch.bme.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Piss-poor sysctl registration API strikes again, film at 11...
What we really need is _pathname_ required to be present in already
registered table, so that kernel could warn about bad order. That's the
next target for sysctl stuff (and generally saner and more explicit
order of initialization of ipv[46] internals wouldn't hurt either).
For the time being, here are full fixups required by ..._rotable()
stuff; we make per-net sysctl sets descendents of "ro" one and make sure
that sufficient skeleton is there before we start registering per-net
sysctls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add struct net_device parameter to ip_rt_frag_needed() and update MTU to
cache entries where ifindex is specified. This is similar to what is
already done in ip_rt_redirect().
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Current ip route cache implementation is not suited to large caches.
We can consume a lot of CPU when cache must be invalidated, since we
currently need to evict all cache entries, and this eviction is
sometimes asynchronous. min_delay & max_delay can somewhat control this
asynchronism behavior, but whole thing is a kludge, regularly triggering
infamous soft lockup messages. When entries are still in use, this also
consumes a lot of ram, filling dst_garbage.list.
A better scheme is to use a generation identifier on each entry,
so that cache invalidation can be performed by changing the table
identifier, without having to scan all entries.
No more delayed flushing, no more stalling when secret_interval expires.
Invalidated entries will then be freed at GC time (controled by
ip_rt_gc_timeout or stress), or when an invalidated entry is found
in a chain when an insert is done.
Thus we keep a normal equilibrium.
This patch :
- renames rt_hash_rnd to rt_genid (and makes it an atomic_t)
- Adds a new rt_genid field to 'struct rtable' (filling a hole on 64bit)
- Checks entry->rt_genid at appropriate places :
A userspace program may wish to set the mark for each packets its send
without using the netfilter MARK target. Changing the mark can be used
for mark based routing without netfilter or for packet filtering.
It requires CAP_NET_ADMIN capability.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, this piece looks relatively easy. Namespace is already
available on the dst entry via device and the device is safe to
dereferrence. Compare it with one of a searcher and skip entry if
appropriate.
The only exception is ip_rt_frag_needed. So, add namespace parameter to it.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_connect and ip_route_newports are a part of routing API
presented to the socket layer. The namespace is available inside them
through a socket.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the ip_route_output_flow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the __ip_route_output_key.
Signed_off_by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only required to propagate it down to the
ip_route_output_slow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
... up to rtentry_to_fib_config
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch extends the inet_addr_type and inet_dev_addr_type with the
network namespace pointer. That allows to access the different tables
relatively to the network namespace.
The modification of the signature function is reported in all the
callers of the inet_addr_type using the pointer to the well known
init_net.
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address type search can be limited to an interface by
inet_dev_addr_type function.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_rt_advice has been gone, so no need to keep prototype and debug message.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the rt_next pointer from 'struct rtable.u' union,
and renames u.rt_next to u.dst_rt_next.
It also moves 'struct flowi' right after 'struct dst_entry' to prepare
the gain on lookups.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this even for non-blocking sockets. This avoids the silly -EAGAIN
that applications can see now, even for non-blocking sockets in some
cases (f.e. connect()).
With help from Venkat Tekkirala.
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_connect(), ip_route_newports() get port numbers net-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
argument and inferred net-endian variables in callers annotated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
annotated address arguments (port number left alone for now); ditto
for inferred net-endian variables in callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first 4 arguments of ip_rt_redirect() are net-endian. Annotated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() takes net-endian source and destination address.
* Annotated as such.
* arguments of its invocations annotated where needed.
* local helpers getting the same values passed to by it (ip_route_input_mc(),
ip_route_input_slow(), ip_handle_martian_source(), ip_mkroute_input(),
ip_mkroute_input_def(), __mkroute_input()) annotated
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This labels the flows that could utilize IPSec xfrms at the points the
flows are defined so that IPSec policy and SAs at the right label can
be used.
The following protos are currently not handled, but they should
continue to be able to use single-labeled IPSec like they currently
do.
ipmr
ip_gre
ipip
igmp
sit
sctp
ip6_tunnel (IPv6 over IPv6 tunnel device)
decnet
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we get an ICMP need-to-frag message, the original TOS value in the
ICMP payload cannot be used as a key to look up the routes to update.
This is because the TOS field may have been modified by routers on the
way. Similarly, ip_rt_redirect should also ignore the TOS as the router
that gave us the message may have modified the TOS value.
The patch achieves this objective by aggregating entries with different
TOS values (but are otherwise identical) into the same bucket. This
makes it easy to update them at the same time when an ICMP message is
received.
In future we should use a twin-hashing scheme where teh aggregation
occurs at the entry level. That is, the TOS goes back into the hash
for normal lookups while ICMP lookups will end up with a node that
gives us a list that contains all other route entries that differ
only by TOS.
Signed-off-by: Ilia Sotnikov <hostcc@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_newports uses the struct flowi from the struct rtable returned
by ip_route_connect for the new route lookup and just replaces the port
numbers if they have changed. If an IPsec policy exists which doesn't match
port 0 the struct flowi won't have the proto field set and no xfrm lookup
is done for the changed ports.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem with promoting aliases when:
a) a single primary and > 1 secondary addresses
b) multiple primary addresses each with at least one secondary address
Based on earlier efforts from Brian Pomerantz <bapper@piratehaven.org>,
Patrick McHardy <kaber@trash.net> and Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of this type, mostly:
CHECK net/ipv6/netfilter.c
net/ipv6/netfilter.c:96:12: warning: symbol 'ipv6_netfilter_init' was not declared. Should it be static?
net/ipv6/netfilter.c:101:6: warning: symbol 'ipv6_netfilter_fini' was not declared. Should it be static?
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 the following unused global function:
- xfrm4_state.c: xfrm4_state_fini
- remove the following unneeded EXPORT_SYMBOL's:
- ip_output.c: ip_finish_output
- ip_output.c: sysctl_ip_default_ttl
- fib_frontend.c: ip_dev_find
- inetpeer.c: inet_peer_idlock
- ip_options.c: ip_options_compile
- ip_options.c: ip_options_undo
- net/core/request_sock.c: sysctl_max_syn_backlog
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It cannot work properly, so just ignore it in drr
and rr multipath algorithms just like the random
multipath algorithm does.
Suggested by Herbert Xu.
Signed-off by: Pravin B. Shelar <pravins@calsoftinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ross moved. Remove the bad email address so people will find the correct
one in ./CREDITS.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
David S. Miller