Pull i2c fixes from Wolfram Sang:
"A core fix for ACPI matching and two driver bugfixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: iproc: Fix shifting 31 bits
i2c: rcar: in slave mode, clear NACK earlier
i2c: acpi: Remove dead code, i.e. i2c_acpi_match_device()
i2c: core: Don't fail PRP0001 enumeration when no ID table exist
Fix undefined behaviour in the iProc I2C driver by using 'BIT' marcro.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
[wsa: in commit msg, don't say 'checkpatch' but name the issue]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
driver and the Designware i2c driver (changes from Akshu Agrawal and
Pu Wen).
-----BEGIN PGP SIGNATURE-----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=D9q+
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
driver and the Designware i2c driver (changes from Akshu Agrawal and
Pu Wen)"
* tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
clk: x86: Support RV architecture
ACPI: APD: Add a fmw property is_raven
clk: x86: Change name from ST to FCH
ACPI: APD: Change name from ST to FCH
i2c: designware: Add device HID for Hygon I2C controller
Pull i2c updates from Wolfram Sang:
- bus recovery can now be given a pinctrl handle and the I2C core will
do all the steps to switch to/from GPIO which can save quite some
boilerplate code from drivers
- "fallthrough" conversion
- driver updates, mostly ID additions
* 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (32 commits)
i2c: iproc: fix race between client unreg and isr
i2c: eg20t: use generic power management
i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume
i2c: mediatek: Fix i2c_spec_values description
i2c: mediatek: Add i2c compatible for MediaTek MT8192
dt-bindings: i2c: update bindings for MT8192 SoC
i2c: mediatek: Add access to more than 8GB dram in i2c driver
i2c: mediatek: Add apdma sync in i2c driver
i2c: i801: Add support for Intel Tiger Lake PCH-H
i2c: i801: Add support for Intel Emmitsburg PCH
i2c: bcm2835: Replace HTTP links with HTTPS ones
Documentation: i2c: dev: 'block process call' is supported
i2c: at91: Move to generic GPIO bus recovery
i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOs
i2c: core: add generic I2C GPIO recovery
dt-bindings: i2c: add generic properties for GPIO bus recovery
i2c: rcar: avoid race when unregistering slave
i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c
i2c: tegra: Fix runtime resume to re-init VI I2C
i2c: tegra: Fix the error path in tegra_i2c_runtime_resume
...
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver calls pci_enable_wake(...., false) in pch_i2c_suspend() as well
as pch_i2c_resume(). Either it should enable-wake the device in .suspend()
or should not invoke pci_enable_wake() at all.
Concluding that this driver doesn't support enable-wake and PCI core calls
pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from
.suspend() and .resume().
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The struct i2c_spec_values have it's members documented but is
missing the starting '@', which leads to warings like:
drivers/i2c/busses/i2c-mt65xx.c:267: warning: Function parameter or member 'min_low_ns' not described in 'i2c_spec_values'
We also delete min_high_ns member as it is not used in the code.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add device HID HYGO0010 to match the Hygon ACPI Vendor ID (HYGO) that
was registered in http://www.uefi.org/acpi_id_list, and the I2C
controller on Hygon paltform will use the HID.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add i2c compatible for MT8192. Compare to MT8183 i2c controller,
MT8192 support more then 8GB DMA mode.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Newer MTK chip support more than 8GB of dram. Replace support_33bits
with more general dma_max_support and remove mtk_i2c_set_4g_mode.
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it need to keep i2c and
apdma in sync manually.
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add SMBus PCI ID on Intel Tiger Lake PCH-H.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for SMBus controller on Intel Emmitsburg PCH. This is the
same IP as used in Cannon Lake and derivatives.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[wsa: shortened commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make the Microchip at91 driver the first to use the generic GPIO bus
recovery support from the I2C core and discard the driver implementation.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAl8eiUATHHJwcHRAbGlu
dXguaWJtLmNvbQAKCRA5A4Ymyw79kWs8B/4wEWVJGTkjyrMX57/Ew8yRYAJE6JjA
kSONPjElVrPR1pRLYyjyde+zqumkJFhk+41De09J2byL29p7tK8ISNrTwJrIN7n/
dzT73CmuNEjI0rZJxPX+USKFph75FQVvAVOOWs+6fiBFxdUaIsBheVntH7/NsCTk
HFrIjIn5wXFVs5Nh+2cHydvEpOVoUWzjvs+uJIEpHCVCBz6gaYq2dxEmeTquKuz1
k7PZqCqVsyB9iWLqN65/Q+30N8znJwcUl8HAzs5nvPrXLjGxwuEjOxtYYhbdLAfP
OBiIF9J77sZxBlms0WNomDW3Rr5Vlt5nF9oUWpi3AmHNWIuX0GkM4i0C
=V+Kl
-----END PGP SIGNATURE-----
Merge tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux
Pull unicore32 removal from Mike Rapoport:
"Remove unicore32 support.
The unicore32 port do not seem maintained for a long time now, there
is no upstream toolchain that can create unicore32 binaries and all
the links to prebuilt toolchains for unicore32 are dead. Even
compilers that were available are not supported by the kernel anymore.
Guenter Roeck says:
"I have stopped building unicore32 images since v4.19 since there is
no available compiler that is still supported by the kernel. I am
surprised that support for it has not been removed from the kernel"
However, it's worth pointing out two things:
- Guan Xuetao is still listed as maintainer and asked for the port to
be kept around the last time Arnd suggested removing it two years
ago. He promised that there would be compiler sources (presumably
llvm), but has not made those available since.
- https://github.com/gxt has patches to linux-4.9 and qemu-2.7, both
released in 2016, with patches dated early 2019. These patches
mainly restore a syscall ABI that was never part of mainline Linux
but apparently used in production. qemu-2.8 removed support for
that ABI and newer kernels (4.19+) can no longer be built with the
old toolchain, so apparently there will not be any future updates
to that git tree"
* tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux:
MAINTAINERS: remove "PKUNITY SOC DRIVERS" entry
rtc: remove fb-puv3 driver
video: fbdev: remove fb-puv3 driver
pwm: remove pwm-puv3 driver
input: i8042: remove support for 8042-unicore32io
i2c/buses: remove i2c-puv3 driver
cpufreq: remove unicore32 driver
arch: remove unicore32 port
Due to the lockless design of the driver, it is theoretically possible
to access a NULL pointer, if a slave interrupt was running while we were
unregistering the slave. To make this rock solid, disable the interrupt
for a short time while we are clearing the interrupt_enable register.
This patch is purely based on code inspection. The OOPS is super-hard to
trigger because clearing SAR (the address) makes interrupts even more
unlikely to happen as well. While here, reinit SCR to SDBS because this
bit should always be set according to documentation. There is no effect,
though, because the interface is disabled.
Fixes: 7b814d852a ("i2c: rcar: avoid race when unregistering slave client")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
VI I2C is on host1x bus so APB DMA can't be used for Tegra210 VI
I2C and there are no tx and rx dma channels for VI I2C.
So, avoid attempt of requesting DMA channels.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
VI I2C is on host1x bus and is part of VE power domain.
During suspend/resume VE power domain goes through power off/on.
So, controller reset followed by i2c re-initialization is required
after the domain power up.
This patch fixes it.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
tegra_i2c_runtime_resume does not disable prior enabled clocks
properly.
This patch fixes it.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
clk_enable, clk_disable, clk_prepare, and clk_unprepare APIs have
implementation for checking clk pointer not NULL and clock consumers
can safely call these APIs without NULL pointer check.
So, this patch cleans up Tegra i2c driver to remove explicit checks
before these APIs.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Tegra VI I2C is part of VE power domain and typically used for
camera usecases.
VE power domain is not always on and is non-IRQ safe. So, IRQ safe
device cannot be attached to a non-IRQ safe domain as it prevents
powering off the PM domain and generic power domain driver will warn.
Current driver marks all I2C devices as IRQ safe and VI I2C device
does not require IRQ safe as it will not be used for atomic transfers.
This patch has fix to make VI I2C as non-IRQ safe.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When the SSR interrupt is activated, it will detect every STOP condition
on the bus, not only the ones after we have been addressed. So, enable
this interrupt only after we have been addressed, and disable it
otherwise.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ports should be defined in the devicetree if they are to be enabled on
the system.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang. The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver. It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.
When the system hangs, I found that it was running the geni_i2c_irq()
over and over again. It had these:
m_stat = 0x04000080
rx_st = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep(). If a transfer makes it
far enough before we do that then we get into the state I have
observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too. Change it as well.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1].
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.
This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.
One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).
So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit d358def706.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Enable i2c transactions in irq disabled contexts like poweroff where the
PMIC is connected via i2c.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Modules with multiple authors should use multiple MODULE_AUTHOR()
statements according to comment in include/linux/module.h.
Split the i2c modules with multiple authors to use multiple
MODULE_AUTHOR() statements.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno
to what is suggested for this error.
Fixes: c9bfdc7c16 ("i2c: mlxcpld: Add support for smbus block read transaction")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michael Shych <michaelsh@mellanox.com>
Tested-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Current AMD's zen-based APUs use this core for some of its i2c-buses.
With this patch we re-enable autodetection of hwmon-alike devices, so
lm-sensors will be able to work automatically.
It does not affect the boot-time of embedded devices, as the class is
set based on the DMI information.
DMI is probed only on Qtechnology QT5222 Industrial Camera Platform.
DocLink: https://qtec.com/camera-technology-camera-platforms/
Fixes: 3eddad96c4 ("i2c: designware: reverts "i2c: designware: Add support for AMD I2C controller"")
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The unicore32 port is removed from the kernel.
There is no point to keep stale i2c bus driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
The port number field in the status register was not correct, so fix it.
Fixes: d6ffb63001 ("i2c: Add FSI-attached I2C master algorithm")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Get the interconnect paths for I2C based Serial Engine device
and vote according to the bus speed of the driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/1592908737-7068-4-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
John Stultz reported that commit f9288fcc5c ("i2c: designware: Move
ACPI parts into common module") caused a regression on the HiKey board
where adv7511 HDMI bridge driver wasn't probing anymore due the I2C bus
failed to start.
It seems the change caused the bus speed being zero when CONFIG_ACPI
not set and neither speed based on "clock-frequency" device property
or default fast mode is set.
Fix this by splitting i2c_dw_acpi_adjust_bus_speed() to
i2c_dw_acpi_round_bus_speed() and i2c_dw_adjust_bus_speed(), where
the latter one has the code that runs independently of ACPI.
Fixes: f9288fcc5c ("i2c: designware: Move ACPI parts into common module")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
"I2C has quite some patches for you this time. I hope it is the move to
per-driver-maintainers which is now showing results. We will see.
The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
larger refactoring of the Designware, Tegra, and PXA drivers, the
Cadence driver supports being a slave now, and there is support to
instanciate SPD eeproms for well-known cases (which will be
user-visible because the i801 driver supports it), and some
devm_platform_ioremap_resource() conversions which blow up the
diffstat.
Note that I applied the Nuvoton driver quite late, so some minor fixup
patches arrived during the merge window. I chose to apply them right
away because they were trivial"
* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
i2c: Drop stray comma in MODULE_AUTHOR statements
i2c: npcm7xx: npcm_i2caddr[] can be static
MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
i2c: npcm7xx: Fix a couple of error codes in probe
i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
i2c: npcm7xx: Remove unnecessary parentheses
i2c: npcm7xx: Add support for slave mode for Nuvoton
i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
dt-bindings: i2c: npcm7xx: add NPCM I2C controller
i2c: pxa: don't error out if there's no pinctrl
i2c: add 'single-master' property to generic bindings
i2c: designware: Add Baikal-T1 System I2C support
i2c: designware: Move reg-space remapping into a dedicated function
i2c: designware: Retrieve quirk flags as early as possible
i2c: designware: Convert driver to using regmap API
i2c: designware: Discard Cherry Trail model flag
i2c: designware: Add Baytrail sem config DW I2C platform dependency
i2c: designware: slave: Set DW I2C core module dependency
i2c: designware: Use `-y` to build multi-object modules
dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
...
It is not the common usage to have a comma between the name and the
email address, so remove it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fixes: f54736925a ("i2c: npcm7xx: Add support for slave mode for Nuvoton")
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
The code here is accidentally returning IS_ERR() which is 1 but it
should be returning negative error codes with PTR_ERR().
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Linus Torvalds