AR9003 does not have a reset control for AHB.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not a stable code fix as this register is not used anywhere.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9300 will be the first device supported of the AR9003
family. AR9300 1.0 hardware exists but it is not going to
be sold anywhere so we completely skip its support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports the AR5008, AR9001 and AR9002 family of Atheros
chipsets, all 802.11n. The new breed of 802.11n chips, the
AR9003 family will be supported as well soon. To help with its
support we're going to add a few callbacks for hardware routines
which differ considerably instead of adding branch checks for
the revision at runtime.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Davinci platforms apparently need more time in-between helper firmware
blocks. Even though this is an increased delay, we only take this hit
once at initialization time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate a bunch of C&P code that waits for the firmware to be ready.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for new rtl818x devices, move the existing rtl818x configuration
into the rtl818x directory.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 is embedded chip that can be connected using SDIO bus, and is not
an actual SDIO card. For this reason there is a need to pass some board
specific data, like 'EEPROM is attached' flag or power control callback.
However currently there is no way to pass this data through SDIO subsystem,
so this patch registers dummy platform_device to allow that, until we
have a better solution to this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug which was just recently introduced by
("p54pci: prevent stuck rx-ring on slow system").
make M=drivers/net/wireless/p54 C=2 CF=-D__CHECK_ENDIAN__
CHECK drivers/net/wireless/p54/p54pci.c
drivers/net/wireless/p54/p54pci.c:143:11: warning: cast to restricted __le32
CC [M] drivers/net/wireless/p54/p54pci.o
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci used the callback write_tx_desc to write the tx descriptor but
also to update the txwi which is part of the dma mapped skb. Since the
memory was already DMA mapped _before_ the call to write_tx_desc the
device didn't get the txwi data at all or only sporadically.
The call order is basically as follows (from rt2x00queue.c):
1) write_tx_data
2) rt2x00queue_map_txskb
3) write_tx_desc
Hence, we shouldn't touch the skb in write_tx_desc anymore.
To fix this issue create a new rt2800pci_write_tx_data callback and use it
for updating the txwi _before_ the memory gets DMA mapped.
The tx descriptor is still written (as before) in write_tx_desc.
This patch allows basic TX on an rt305x soc device but I'm pretty sure
that it will fix pci based cards as well. I can associate just fine with
an AP now but I wasn't able to get a wpa secured connection working yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend the write_tx_data callback with a txdesc parameter to allow
access to the tx desciptor while preparing the tx data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some wl1251 hardware configurations (like in WG7210 module) have
EEPROM attached where NVS data is kept, which includes MAC address.
In such configurations, let's read default MAC address from EEPROM,
instead of using random one.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the following 5 entries to the usbid device table:
* Netgear WNA1000
* Proxim ORiNOCO Dual Band 802.11n USB Adapter
* 3Com Dual Band 802.11n USB Adapter
* H3C Dual Band 802.11n USB Adapter
* WNC Generic 11n USB dongle
CC: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If EEPROM is used, NVS data is now loaded but ignored.
Stop loading it to avoid need of dummy NVS file for modules with EEPROM.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k-htc register out path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k-htc register in path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k_hif_usb_alloc_rx_urbs, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skbs allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get RXORN interrupts when all receive buffers are full. This is not
necessarily a fatal situation. It can also happen when the bus is busy or the
CPU is not fast enough to process all frames.
Older chipsets apparently need a reset to come out of this situration, but on
newer chips we can treat RXORN like RX, as going thru a full reset does more
harm than good, there.
The exact chip revisions which need a reset are unknown - this guess
AR5K_SREV_AR5212 ("venice") is copied from the HAL.
Inspired by openwrt 413-rxorn.patch:
"treat rxorn like rx, reset after rxorn seems to do more harm than good"
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a confusion in the usage of the bits AR5K_STA_ID1_ACKCTS_6MB and
AR5K_STA_ID1_BASE_RATE_11B. If they are set (1), we will get lower bitrates for
ACK and CTS. Therefore ath5k_hw_set_ack_bitrate_high(ah, false) actually
resulted in high bitrates, which i think is what we want anyways. Cleared the
confusion and added some documentation.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RT3390 specific register initializations to rt2x00, based on the latest
Ralink rt3390 vendor driver.
Untested as I don't actually own an RT3390 based device, but given experiences
on rt3070/rt3071 very hopeful that this will actually work..
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RT3090 specific register initializations to rt2x00, based on the latest
Ralink rt3090 vendor driver.
Untested as I don't actually own an RT3090 based device, but given experiences
on rt3070/rt3071 very hopeful that this will actually work..
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RT3071 specific register initializations to rt2x00, based on the latest
Ralink rt3070 vendor driver.
With this patch my RT3071 based devices start showing a sign of life.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 had preliminary support for RT3070 based devices, but the support was
incomplete.
Update the RT3070 register initialization to be similar to the latest Ralink
vendor driver.
With this patch my rt3070 based devices start showing a sign of life.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align the rt2800 register initializations with the latest versions of the
Ralink vendor driver.
This patch is also preparation for the addition of support for RT3070 /
RT3071 / RT3090 / RT3390 based devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800 version constants are inconsistent, and the version number don't
mean a lot of things anyway. Refactor the constants to have some more
meaningful names, and introduce and use some new helpers to check these
chipset revisions. At the same time rename to revision, as they are more
revision numbers rather than version numbers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only include definitions for RT chipsets that are also used inside the
Ralink vendor drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Definitions taken from the latest rt2860 / rt2870 / rt3070 / rt3090 Ralink
vendor drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that the distinction between RF channel switch method is solely based
on the RF chipset that is used.
Refactor the channel switch decision to just take the RF chipset into account,
thereby greatly simplifying the check.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an old problem, which - under certain
circumstances - could cause the device to become
unresponsive.
most of p54pci's rx-ring management is implemented in just
two distinct standalone functions. p54p_check_rx_ring takes
care of processing incoming data, while p54p_refill_rx_ring
tries to replenish all depleted communication buffers.
This has always worked fine on my fast machine, but
now I know there is a hidden race...
The most likely candidate here is ring_control->device_idx.
Quintin Pitts had already analyzed the culprit and posted
a patch back in Oct 2009. But sadly, no one's picked up on this.
( https://patchwork.kernel.org/patch/53079/ [2 & 3] ).
This patch does the same way, except that it also prioritize
rx data processing, simply because tx routines *can* wait.
Reported-by: Sean Young <sean@mess.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11386
Reported-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Check return code on iwl_send_cmd_pdu() to get rid of compiler warning.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-agn-rs.o
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2419: warning: unused variable ‘priv’
CC [M] drivers/net/wireless/iwlwifi/iwl-sta.o
drivers/net/wireless/iwlwifi/iwl-sta.c: In function ‘iwl_send_add_sta’:
drivers/net/wireless/iwlwifi/iwl-sta.c:197: warning: unused variable ‘sta_id’
drivers/net/wireless/iwlwifi/iwl-3945.c: In function ‘iwl3945_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-3945.c:601: warning: unused variable ‘rx_stats_noise_diff’
drivers/net/wireless/iwlwifi/iwl-3945.c:600: warning: unused variable ‘rx_stats_sig_avg’
drivers/net/wireless/iwlwifi/iwl-3945-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-3945-rs.c:650: warning: unused variable ‘priv’
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
REPLY_TX_LINK_QUALITY_CMD was used by 4965, 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Update to include additional tx command response status for "_agn"
devices.
The following status indicate the transmission was postponed:
TX_STATUS_POSTPONE_DELAY
TX_STATUS_POSTPONE_FEW_BYTES
TX_STATUS_POSTPONE_BT_PRIO
TX_STATUS_POSTPONE_QUIET_PERIOD
TX_STATUS_POSTPONE_CALC_TTAK
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When sys assert happen, driver will dump the error table information
provided by uCode. There are more information available but is not being
display by the driver; adding program counter and last host command the
to log to help uCode debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The last_phy_res[100] variable is used in an odd
way. The first byte of it is used as a flag, and
the rest as the data. Thus, the array need only
be 61 bytes, since it is just the flag and a
struct iwl_rx_phy_res (which is 60 bytes).
Clean this up by splitting the variable into two:
last_phy_res and last_phy_res_valid, using correct
types for both (struct and bool). While doing all
this also move the variables to the _agn part of
the hw-specific union since they only apply to
A-MPDUs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
lq->sta_id cannot be invalid here since this
function will only be called after the station
has been added properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Simplify the WEP group key check by checking the
sta pointer instead of the sta_id we calculate
with it; also clean up the comment formatting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Default WEP keys and regular keys are not allocated
from the same space in the firmware, so we shouldn't
use the same bits to indicate in use.
For default WEP keys, however, mac80211 won't allow
using the same key index twice, so the check is not
necessary at all -- add/remove are perfectly nested
due to those checks.
Other keys are allocated in the device in a global
array that only has a certain number of slots, so
for that we need to keep the allocation bitmap; but
the 802.11 key index isn't relevant there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The firmware clears default WEP keys on
transitions to !associated, so we need
to restore them just like stations. This
is rather implicit as part of sending a
station right now, which is odd. Make it
explicit instead and only for agn since
3945 doesn't use hw crypto for WEP.
Due to that, iwl_send_static_wepkey_cmd
is now only used in iwl-sta.c and can be
static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Size of event log is determined by uCode which is different per NICs.
Set the maximum event log size per device to better match uCode
configuration.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.
The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.
This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch will add support for connection quality monitoring by configuring
rssi triggers to the firmware, and enabling the firmware rssi trigger
functionality.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow the wl1271 go to ELP mode also in idle. This will reduce current
consumption remarkably in idle mode (~12mA -> ~0.2mA)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends RTS threshold configuration request even if the wl1271 interface
state is WL1271_STATE_OFF. This leads to failures during pm tests.
This patch leaves the configuration function, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends configuration requests even if the wl1271 interface
state is WL1271_STATE_OFF. This creates warnings from mac80211.
This patch leaves the configuration functions, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some memory leaks occurring during driver init/de-init.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resolution of a merge conflict upstream accidentally removed a hunk of
"ath5k: IQ calibration for AR5211 is slightly different", so restore it.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simple pre-scan and scan complete callbacks, this at least shows
to me that mac80211 will issue two scans at the same time on the
same wiphy.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check the bounds on pdadc once when correcting for
negative curves but not when we later copy values from
from the pdadc_tmp array, leading to a potential overrun.
Although we shouldn't hit this case in practice, let's
be consistent.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Benoit Papillault, there is a potential
race condition between the host and the hardware in reading
the next link in the transmit descriptor list:
cpu0 hw
tx for buf completed
raise tx_ok interrupt
process buf
buf->ds_link = 0
read buf->ds_link
This change checks txdp before processing a descriptor
(if there are any subsequent descriptors) to see if
hardware moved on. We'll then process this descriptor on
the next tasklet.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a couple of strange invocations to
ieee80211_wake_queues that could potentially cause problems:
- queues are awakened in the calibration tasklet before
phy calibration, and then again after calibration
- queues are awakened inside reset when we're trying to
drain the ath5k transmit queues, and again after
reset is completed (in callers to ath5k_reset_wake).
In both cases the first wake is unnecessary, so remove it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These channels aren't selectable anyway, but our calculations
for 2.5 mhz frequencies are incorrect. The value is supposed to
be:
(frequency - reference) * (10/25)
i.e., divide by 2.5, but we were instead doing:
(10 * frequency - reference) / 25.
Additionally, the check for (frequency % 5 == 2) had an extra
subtraction that wasn't in madwifi HAL.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2872 needs the same rf register setup as rt3070 and rt3090, hence
use rt2800_config_channel_rt3x instead of rt2800_config_channel_rt2x.
This change allows me to actually switch channels and hence scan all
configured channels on the RT305x SoC platform (which uses a rt2872)
here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't modify ah->iniModes, it's supposed to be constant. Instead, apply
the fixup when the data is written to the registers.
Change ath9k_hw_init_eeprom_fix() to only determine whether the fixup is
needed.
This allows similteneous support for AR9220 cards that need AR_AN_TOP2
fixup (such as Ubiquiti SR71-12) and those that don't need it (D-Link
DWA-552 rev A2).
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Messages that are generated by the HTC layer
don't have any TX callback endpoints assigned to them.
Consequently, the allocated SKBs are never freed.
Fix this issue by handling this case in the HTC layer
itself.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hif_usb_regout_cb() frees the given URB, which is
borked by design. Use an anchor to simplify URB
management.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maximum number of packets in a single buffer in
stream mode is 10. The driver currently uses 8 - which
caused stack corruption, in the absence of any kind
of OOB checking.
Fixing this to the correct value of 10 fixes the module
unload issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX URBs are automatically freed when the reference
count drops to zero - this currently doesn't happen when
usb_kill_anchored_urbs() is called during unload.
Fix this by dropping the reference count by one during
initial submission.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a spin lock to prevent concurrent access
to variables dealing with RX stream mode handling.
Currently, no protection is implemented - which
causes problems in RX.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the powersave issues on rt2500usb have been tackled, powersave
can be enabled by default again.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for a modified newer version of AR9285
chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Better use the macro for consistency, the content is the same anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked
at both ath9k and HAL sources (they are nearly the same), and even though i
have implemented some things differently, the basic algorithm is practically
the same, for now. I hope that this can serve as a clean start to improve the
algorithm later.
This also adds a possibility to manually control ANI settings, right now only
thru a debugfs file:
* set lowest sensitivity (=highest noise immunity):
echo sens-low > /sys/kernel/debug/ath5k/phy0/ani
* set highest sensitivity (=lowest noise immunity):
echo sens-high > /sys/kernel/debug/ath5k/phy0/ani
* automatically control immunity (default):
echo ani-on > /sys/kernel/debug/ath5k/phy0/ani
* to see the parameters in use and watch them change:
cat /sys/kernel/debug/ath5k/phy0/ani
Manually setting sensitivity will turn the automatic control off. You can also
control each of the five immunity parameters (noise immunity, spur immunity,
firstep, ofdm weak signal detection, cck weak signal detection) manually thru
the debugfs file.
This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies tx-queue flushing to correspond with tx-path - i.e.
also frames for which no ack was requested are forwarded to the mac80211
for disposal.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ERROR print from psm-entry-fail scenario, instead use an INFO print.
Also, add INFO print to the beacon-loss scenario.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the fixed listen-interval max value configured to the mac80211 on
driver init. This value will allow a larger value to be configured to the
AP, which means the AP will buffer our frames longer.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure meaningful rates to be used with the templates. For control frames,
use the determined basic rates (currently the lowest rate for the band) and
for data-frames (null-funcs) let the firmware use the current rate policy to
determine the rate.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mac80211 is not telling a hardware rate controlled driver a
rate to use for association frames etc. So to be safe, use the lowest rate
of each band for communication.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware does not like the host configuring the keep-alive after it has
been once configured after a join-operation. Instead, it will complain about
invalid parameters, which do not break functionality, but do not look nice
in the syslog either.
This patch prevents the complaints by only configuring the keep-alive once
for an association, after the first time join is performed with the correct
bssid.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The command header was missing in the wl1271_cmd_disconnect structure. It
was working fine by sheer luck, because the parameters are not critical and
because our wl1271_cmd_send() function was overwriting the rx_config_options
with the actual header.
This patch adds the header to the command structure.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our SPI driver is called "wl1271_spi" in the driver information structure.
Let's use the same for SDIO so that things are aligned.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, this check is invalid.
Remove the check so that new product IDs can be added.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used to store the bus types ( AHB/PCI/USB ).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commits 8e6f5aa250 and
db1a052b73 accidentally introduced
compile errors that happens when ath9k debug is not enabled.
This patch fixes the declaration of the inline stubs to resolve this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->mask_reg was used to hold different data throughout the driver.
ath9k_hw_init_interrupt_masks() used it to save the value written to
AR_IMR. ath9k_hw_set_interrupts() used it to hold the interrupt mask as
defined in enum ath9k_int. Those masks differ in many bits.
Use ah->imask instead of ah->mask_reg in ath9k_hw_set_interrupts() and
ath9k_hw_updatetxtriglevel(). That's what the code was meant to do.
ah->imask is initialized in ath9k_start(), so we don't need to
initialize it from ah->mask_reg.
Once it's done, ah->mask_reg becomes write-only, so it's replaced with a
local variable in ath9k_hw_init_interrupt_masks().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ah variable in the functions that didn't have it and used sc->imask.
Replace sc->sc_ah with ah in those functions.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbols starting with "ATH9K_INT" are also used for interrupt mask.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to files in ath/ar9170 that fixes a set of warnings
found by checkpatch.pl tool. A line over 80 characters, a few empty
spaces before tab and a few empty characters before a new line.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In all drivers ensure that auto wakeup is disabled before waking up the device.
This is needed to prevent connection stability issues and problems in waking up
the device.
Based upon a patch from Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.
Thanks to Alagu Sankar for pointing me in the right direction.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alagu Sankar <alagusankar@embwise.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/regd.c file that fixes two code
readability issues. A space between to separate two defines
and the indentation inside the ath_redg_is_eeprom_valid
function.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/hw.c file that fixes up a warning about
macros found by the checkpatch.pl tool, that said that complex values
should be enclosed in parenthesis.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ralink SoC platforms do not have an MCU.
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Includes minor improvements in debugging messages in iwl-4965.c,
function iwl4965_is_temp_calib_needed().
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some defines used by all agn devices, but the definitions were in
iwl-4965-hw.h, move those to iwl-agn-hw.h which is the better place for
those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In iwl_rx_queue_reset(), we didn't clear the rxq->queue[]. This might
cause the same rxb appears on multiple places in rxq->queue. Although
this won't cause any problem because of the read and write pointers
protection in rxq, we'd better clear it to avoid misleading.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Module parameters used to be defined in both iwl-5000.c and iwl-4965.c,
after the code re-structure, merge into iwl-agn.c for easy to read and
maintenance.
Number of module parameters are deprecated after this merge. These are also
scheduled for removal by 2.6.40.
The current supported parameters are:
parm: debug50:50XX debug output mask (deprecated) (uint)
parm: debug:debug output mask (uint)
parm: swcrypto50:using crypto in software (default 0 [hardware])
(deprecated) (bool)
parm: swcrypto:using crypto in software (default 0 [hardware]) (int)
parm: queues_num50:number of hw queues in 50xx series (deprecated)
(int)
parm: queues_num:number of hw queues. (int)
parm: 11n_disable50:disable 50XX 11n functionality (deprecated) (int)
parm: 11n_disable:disable 11n functionality (int)
parm: amsdu_size_8K50:enable 8K amsdu size in 50XX series (deprecated)
(int)
parm: amsdu_size_8K:enable 8K amsdu size (int)
parm: fw_restart50:restart firmware in case of error (deprecated) (int)
parm: fw_restart:restart firmware in case of error (int)
parm: disable_hw_scan:disable hardware scanning (default 0) (int)
Remove "antenna" module parameter, it is not being used in "agn" driver.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().
To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Henry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
While ar9170's USB transport packet size is currently set to 8KiB,
the PHY is capable of receiving AMPDUs with up to 64KiB.
Such a large frame will be split over several rx URBs and
exceed the previously allocated space for rx stream reconstruction.
This patch increases the buffer size to 64KiB which is
in fact the phy & rx stream designed size limit.
Cc: stable@kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=15591
Reported-by: Christian Mehlis <mehlis@inf.fu-berlin.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 skips drop_unencrypted checks if the driver/firmware has
already taken care of this. In case of ath9k, we must not indicate
that the frame was decrypted if no decryption was actually done.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set IEEE80211_HW_RX_INCLUDES_FCS to indicate that
the FCS is present in RX frames. Also, remove a redundant
assignment of skb length and include the FCS_LEN
when checking padding.
Fixing this issue makes TKIP work.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_status and ath_rx_status data are only necessary for a short
time, until they have been processed and converted into mac80211 data
structures.
Because of that, it makes no sense to keep them tied to the DMA
descriptor, that only wastes precious memory.
This patch allocates the data on stack in the functions that call the
conversion functions from ath9k_hw.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch passes in a pointer to the ath_rx_status data structure for
functions that need it, instead of letting them grab it directly from
the ath_desc struct. This is useful for making it possible to allocate
the intermediate rx status data separately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch passes in a pointer to the ath_tx_status data structure for
functions that need it, instead of letting them grab it directly from
the ath_desc struct. This is useful for making it possible to allocate
the intermediate tx status data separately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan watchdog is fired, try to send abort scan command
first before restarting the adapter. This avoids reconnection for
some users when scan hang is detected.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15419
Reported-by: Maurizio Avogadro <mavoga@gmail.com>
Tested-by: Maurizio Avogadro <mavoga@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not setting the opmode properly during initialization
results in the firmware sending up a bunch of packets
before add_interface() has been called, for the first
interface.
This patch fixes the issue by setting the initial mode
to 'managed'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stop/restart TX queues when the internal SKB
queue is full. This helps handle TX better
under heavy load.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the usage of URB anchors,
thus reducing a large amount of code dealing with
URB maintenance within the driver. The RX callback now
takes care of freeing the SKB associated with each URB.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip beyond the watchdog pattern properly.
This fixes occasional failure of the driver to load.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing the sta pointer in TX completion without
approprate RCU protection is wrong. Fix this.
Also, RCU protection is needed when the station's
aggregation state is updated. Handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculation of RX filter is fairly different
between ath9k and ath9k_htc, trying to make this
common between the two drivers would result in code churn.
While at it, remove the handling of PSPOLL filter,
it can be added when(if) AP support is added to ath9k_htc.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We activate/deactivate QoS and setup default queue parameters in iwlwifi
driver. Mac stack do the same, so we do not need repeat that work here.
Stack also will tell when disable QoS, this will fix driver when working
with older APs, that do not have QoS implemented.
Patch make "force = true" in iwl_active_qos() assuming we always want
to do with QoS what mac stack wish.
Patch also remove unused qos_cap bits, do not initialize qos_active = 0,
as we have it initialized to zero by kzalloc.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove skb_linearize() in the iwlwifi drivers since
mac80211 supports paged rx SKBs now.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to partially change chanspec just to find out there is not
entry in table for given channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Taken from latest ralink linux driver(RT3070_LinuxSTA_V2.3.0.1_20100208)
All of them are RT3070 devices.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Taken from latest ralink linux driver, it's a RT3593 PCI/PCIe.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was removed in the windows inf file by ralink.
And it isn't on ralink linux drivers.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After last transmission, the device goes to sleep earlier
than the configured dynamic power save timeout. If timeout
is set to 400ms, device enters into sleep mode at around
330ms since from last TX.
This patch removes the msleep(1), which causes the delay
after ELP wakeup. Replaced with udelay(10), the variation
is around 7-10ms.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will enable the hardware keep-alive mode, configure the required
template, configure keep-alive parameters, and re-order JOIN's and ACX_AID
in such a way that the keep-alive is activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for keep-alive templates, which are indexed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures the mac80211 to not perform connection monitoring
(periodic probe-requests) and instead rely on the hardware to do it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If PSM entry fails despite of retries, assume that the AP has been lost,
and indicate connection loss to the mac80211. This is much safer than
remaining in active mode.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure a probe-request template to the wl1271 when associated - the
wl1271 will use this to attempt to recover a connection when beacon loss
is detected.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver tx-queue flush operation leaks broadcast-frames. This leak occurs
if the driver is shut down while there are frames in TX buffers (such as in
a firmware crash scenario.) Fix the leak.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the driver to call ieee80211_beacon_loss function always when
BSS_LOST_EVENT is received. Reason for the change is that entering PSM
might fail before driver receives BSS_LOST_EVENT. In such case the
driver would disable PSM and the stack would not be notified about beacon
loss and connection loss detection would be delayed by tens of seconds.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the hardware beacon interval to whatever requested by the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the driver to better reflect the ad-hoc related configuration from the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 does not support disabling the connection monitor feature.
Perform the next best thing by increasing the beacon-loss threshold and
BSS_LOSE event timeout to the maximum values.
This is needed, because we really don't want any random probe-requests during
scanning or especially while in ad-hoc mode and not beaconing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise element in the ieee80211_rx_status struct has been deprecated in
commit "mac80211: deprecate RX status noise". Remove the usage of this
element from wl1271_rx.c to avoid warnings.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wait for the DISCONNECT_EVENT_COMPLETE_ID event after sending a disconnect
command.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Poll for join command completion instead of waiting blindly for 10 msecs.
There is a timeout of 100 msecs, if the command doesn't complete by then, we
return an error code.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the MAC address randomization from the driver. This removes
a nasty Nokia-OUI dependency from the driver.
With this patch, unless an address is explicitly configured to the driver
by the user, only a zero address will be configured, and the driver will be
unable to start.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the busy-words, if the firmware did not complete by the end of the
first (fixed) busy-word, a flip of the CS line is required to enable clocking
out the actual read data.
This patch changes the mechanism such that the CS line is flipped after each
busyword.
Also, the busy-word mechanism is finally enabled, and the number of fixed
busywords reduced to the minimum.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a trivial memory leak in cmd_data_path.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were wrong format specifiers in wl1271_sdio.c in some debug
outputs. This has been causing warnings on some platforms.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures the wl1271 chipset clock-request line to be
driver in open-drain mode instead of push-pull.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak in the scan command handling code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two memory leaks in the SPI initialization code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add reporting of the used TX rate to mac80211 in the tx_status.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the code to convert a firmware rate class index into an index
for the rate configuration table.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When forward porting some patches to upstream, there was a mistake and the
wl1271_spi driver name remained, erroneously, as "wl1271". This patch fixes
that.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chipsets since revision AR5213A (0x59) have hardware counters for PHY errors
which we can read directly from the registers. Older hardware has to use the RX
descriptor status to get a count of PHY errors. This will be used in several
places in the ANI implementation, so a flag is useful.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PHY error codes from the HAL, and keep them in statistics for debugging
via the 'frameerrors' file. This will also be used by ANI.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let's keep MIB counter statistics in our own statistics structure and only
convert it to ieee80211_low_level_stats when needed by mac80211. Also we don't
need to read profile count registers in the MIB interrupt (they don't trigger
MIB interrupts).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize noise floor variable with a default of -95. This was used
uninitialized in the signal strength (RSSI -> dBm) conversion until the first
noise floor calibration was completed.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keep an exponentially weighted moving average of the beacon RSSI in our BSS.
It will be used by the ANI implementation.
The averaging algorithm is copied from rt2x00, Thanks :)
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not a phy related funtion; It has more to do with the interrupt handler
and tasklet scheduling, so it belongs to base.c.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Optimize ath5k_hw_calibration_poll() since it is called on every singe
interrupt.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need to generate a software interrupt (SWI) just to schedule a tasklet
- we can just schedule the tasklet directly.
Rename constants, names, etc to reflect the fact that we don't use SWI any more.
Also move the flag handling into the tasklet and prepare it to behave correctly
when there are multiple flags present.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove static variable ath5k_calinterval which was used as a constant. Use a
#define instead. Also we don't need ah_cal_intval.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.
IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.
rates = kzalloc((sizeof(struct ieee80211_rate) * IWL_RATE_COUNT_LEGACY),
GFP_KERNEL);
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: stable@kernel.org
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An int urb is constructed but we fill it in with a bulk pipe type.
Commit f661c6f8c6 implemented a pipe type
check when CONFIG_USB_DEBUG is enabled. The check failed for all the ar9170
usb transfers and the driver could not configure the wifi dongle.
This went unnoticed until now because most people don't have
CONFIG_USB_DEBUG enabled.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Stable <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent bug reports have shown that rt2500usb also suffers from the
powersave problems that the PCI rt2x00 drivers suffer from.
So disable powersaving by default for rt2500usb as well.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously in interrupt handling tasklet, iwlwifi driver only clear/ack
those interrupts that are enabled by the driver through inta_mask.
If the hardware generates unattended interrupts, driver will not ack them,
defeating the interrupt coalescing feature. This results in high number
of interrupts per second and high CPU utilization.
This patch addresses this issue by acking those unattended interrupts
in the tasklet. Local test showed an order of magnitude improvement
in terms of the number of interrupts without sacrificing networking
throughput. This is a workaround for hardware issue.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Forget one hunk in 4965 during "iwlwifi: error checking for number of tfds
in queue" patch.
Reported-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Thanks to Chris Chabot for giving his old wireless usb dongle to me
to test it under Linux.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the NEC WL300NU-G USB wifi dongle.
Signed-off-by: Ben Konrath <ben@bagu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid checking for specified device type to perform certain function,
switch to .cfg approach as more generic and better implementation
method.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Use spin_lock_irqsave() in interrupt handler to disable interrupts locally
and provide the spinlock on SMP. This covers both interrupt and SMP
concurrency.
With this changes, also fix the sparse warning issues.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Remove the "\n" from following module parameter description:
- enable wifi/bluetooth co-exist
- led mode: 0=blinking, 1=On(RF On)/Off(RF Off), (default 0)
to be consistence with the rest of iwlagn/iwlcore module parameters format.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In stead of checking for 4965 and do KELVIN_TO_CELSIUS conversation, add
.cfg parameter for more generic approach.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We go to great lengths to calculate this value
that is never used by mac80211. Additionally,
it is now deprecated by mac80211 and is causing
driver compilation to give warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
After re-structure the agn files layout and move all the
agn shared functions out from iwl-5000.c, all those functions and data
structures do not need to be declare "extern" from iwl-5000.c in
iwl-dev.h.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move more functions only used by agn driver from iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Identify the rx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Identify the tx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
agn module parameter data structure shared by all agn devices, move it
iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Each device has it own eeprom, so the tx power version could be
different, define TX_POWER_VERSION per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices share the same common functions.
Move those functions from iwl-5000.c to iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
uCode alive for iwlagn based devices share the same functions.
Move those functions from iwl-5000.c to iwl-agn-ucode.c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hw definitions.
Move device hardware related defines from iwl-5000-hw.h to iwl-agn-hw.h
file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same tansmit queue functions.
Move tx queue related code from iwl-5000.c to iwl-agn-tx.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hcmd related functions.
Move from iwl-5000.c to iwl-agn-hcmd.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Loading uCode functions are shared across multiple agn devices.
Move those functions to iwl-agn-ucode.c file with other uCode
related functions.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same ucode loading procedure.
Move loading related code from iwl-5000.c to iwl-agn-ucode.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_good_ack_health() check for expected and actual ack count which only
apply to aggregation mode. Move the function to iwlagn module.
Reported-by: Chantry Xavier <chantry.xavier@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This reverts commit 76232ebf89.
iwl_good_ack_health only applies to aggregation and thus only to iwlagn. We
can thus move the function to iwlagn instead of modifying compile flags.
This is done in following patch.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_good_ack_health':
drivers/net/wireless/iwlwifi/iwl-rx.c:647: error: 'struct iwl_priv' has no member named '_agn'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto auth mode is enabled by default. If user doesn't specify the
auth mode, while association driver will first try with open mode
and then with shared key mode. If user specifies an auth mode,
auto auth is disabled and driver will not try association with
another auth mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Daniel Ngu <daniel.dy.ngu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change local functions that are cast to iw_handler to
the more standard use with "union iwreq_data *wrqu"
so the iw_handler array no longer needs the casts.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert direct uses of [ (foo - SIOCIWFIRST) , fn)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed platform_device to be allocated dynamically from the
wl1271_alloc_hw function. Also cleaned up error handling in the
wl1271_alloc_hw function and module probe functions.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing the wl1271 from the inet addr notifier chain sometimes causes the
registered handler to be called - causing locking problems if the removing
function is called from within the mutex.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The null func template is not needed for ad-hoc, and it's generation is not
supported for ad-hoc (mac80211 will WARN about it.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the filters configured by the mac80211 stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed duplicate code from wl1271_sdio module remove function. For
freeing stuff in the remove function wl1271_free_hw function is now
used.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added separate flag for SDIO debugging. Previously it has used
DEBUG_SPI flag. This patch also includes couple indentation fixes.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's no longer needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes MAC address handling. To achieve this, firmware booting had
to be delayed from the previous op_start to op_add_interface, which is the point
when the driver gets to know the configured MAC address. As the wl1271 only
supports one virtual interface, this even seems quite logical.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271 supports U-APSD similarly as wl1251, so let's enable it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "wl1271: implement WMM" accidentally used CONF_PS_SCHEME_LEGACY_PSPOLL,
but instead CONF_PS_SCHEME_LEGACY should be used as earlier.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for U-APSD.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we get probe request from mac80211, we can remove two functions.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 now can create pspoll and nullfunc templates, better to use those.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everything is ready now and we can enable WMM in wl1271.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a sysfs file to control the state of the BT co-ex (enable or disable it.)
By default, the BT co-ex is enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to get the platform device for both SPI and SDIO, move the platform
device registration to wl1271_main.c from wl1271_spi.c.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add configuration values for the varous WLAN-BT co-ex configuration parameters,
and finally enable WLAN-BT co-ex. Based on preliminary measurements, it
appears the co-ex feature is not increasing WLAN power consumption, if BT
is not activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bluetooth coexistence (SG) configuration messages have changed and
were completely wrong. For instance, intending to enable the SG, it was
instead disabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed driver to keep MMC host claimed while wlan interface is up.
This keeps MMC stack from powering the SDIO device down.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added method for wlan power control to io_ops struct and moved
wl1271_power_on and wl1271_power_off functions to wl1271_io.h.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The per-queue TX opportunity value is configured by the mac80211 in units
of 32us. The firmware however wants it in us, so add the conversion.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this you will get a panic if the device initialization
fails. Also, free ath_hw instance properly. ath9k_hw_deinit()
shouldn't do it.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9271 needs a full reset only upon the first reset, add
a call for the driver to enable these special resets. We
can optimize this out later without an export.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initializing the PLL on AR9271 we always need
to set the core clock to 117MHz. While at it remove
the baud rate settings for the serial device on the
AR9271, the default settings work well unless you
want to customize it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Periodic power amplifier offset calibration is skipped on ath9k
algorithmically, this is required on AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noisefloor values read on AR9271 are unreliable if they
are less than -114, set those statically to -116.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noisefloor calibration involves querying hardware for samples
and storing this information on a history buffer in hardware for
actual noisefloor calibration processing in hardware. The history
buffer supports collecting information for all Atheros hardware,
one history buffer slot for each chain on each channel used for
MIMO operation. For current hardware this means one history
buffer slot for each chain on both the control (or primary) channel
and the extension (or secondary) channel. We know which noisefloor
registers to poke for collecting noisefloor data through the
chainmask.
For AR9285 and AR9271 devices, both 1x1, the chaimmask is defined as
0x9 = 0b0001001. The first four bits represent each chain out of
a maximum of 4 chains [0-3] on the primary channel. The last four
bits represent each chain on the extension channel. A chainmask
of 0x9 therefore indicates chain 1 is active on both the primary
and the extension channel.
AR9271 only requires collecting and storing noisefloor history buffer
data for the first chain on both the control and extension channel
(nfarray[0] and nfarray[3]) so fix the code and avoid which reads
and writes to the history buffer for the other chains.
Since the noisefloor varies depending on the number of chains your
device supports also initialize the noisefloor history buffer with
reasonable values seen on 1x1 devices such as AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After telling the AR9271 to go into full sleep we do not need
to clear the RTC reset signal.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX descriptors setup for AR971 requires the same
setup as AR9285, so use that.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip test is not required for AR9271 on the host driver
code as the firmware will do the test internally on its own.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the proper number of GPIO pins for AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the register initialization values for AR9271.
This is based on our last review from our systems team.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From e74b075cdb143d45be9b371ee8a8e2dcfc15ab34 Mon Sep 17 00:00:00 2001
From: Ming Lei <tom.leiming@gmail.com>
Date: Sat, 27 Feb 2010 23:50:54 +0800
Subject: [PATCH] ath9k: decrease size of ath9k.ko
The patch defines the fields of 'valid_single_stream' and 'valid' in
struct ath_rate_table as char type, so decrease the size of ath9k.ko
about 2KB.
old ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
69344 3080 168 72592 11b90 ath9k.ko
new ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
67304 3080 168 70552 11398 ath9k.ko
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the connectivity check and recovery routine into separated
functions based on the types
1. iwl_good_ack_health() - check for ack count
2. iwl_good_plcp_health() - check for plcp error
Based on the type of errors being detected, different recovery methods
will be used to bring the system back to normal operational state.
Because different NIC has different HW and uCode, the behavior is also
different; these functions thus now form part of the ops infrastructure,
so we can have more control on how to monitor and recover from error condition
case per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the
expected_ack_count also drops. At the same time, the aggregated
ba_timeout (the number of ba timeout retries) also rises. If the
actual_ack_count/expected_ack_count ratio is 0 and the number of ba
timeout retries rises to BA_TIMEOUT_MAX, no tx packets can be delivered.
Reloading the uCode and bring the system back to normal operational
state.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the plcp error checking into stand alone function and pointed by ops
to accommodate devices not needing this recovery.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Luis R. Rodriguez