Allow the wl1271 go to ELP mode also in idle. This will reduce current
consumption remarkably in idle mode (~12mA -> ~0.2mA)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends RTS threshold configuration request even if the wl1271 interface
state is WL1271_STATE_OFF. This leads to failures during pm tests.
This patch leaves the configuration function, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends configuration requests even if the wl1271 interface
state is WL1271_STATE_OFF. This creates warnings from mac80211.
This patch leaves the configuration functions, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some memory leaks occurring during driver init/de-init.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resolution of a merge conflict upstream accidentally removed a hunk of
"ath5k: IQ calibration for AR5211 is slightly different", so restore it.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simple pre-scan and scan complete callbacks, this at least shows
to me that mac80211 will issue two scans at the same time on the
same wiphy.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check the bounds on pdadc once when correcting for
negative curves but not when we later copy values from
from the pdadc_tmp array, leading to a potential overrun.
Although we shouldn't hit this case in practice, let's
be consistent.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Benoit Papillault, there is a potential
race condition between the host and the hardware in reading
the next link in the transmit descriptor list:
cpu0 hw
tx for buf completed
raise tx_ok interrupt
process buf
buf->ds_link = 0
read buf->ds_link
This change checks txdp before processing a descriptor
(if there are any subsequent descriptors) to see if
hardware moved on. We'll then process this descriptor on
the next tasklet.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a couple of strange invocations to
ieee80211_wake_queues that could potentially cause problems:
- queues are awakened in the calibration tasklet before
phy calibration, and then again after calibration
- queues are awakened inside reset when we're trying to
drain the ath5k transmit queues, and again after
reset is completed (in callers to ath5k_reset_wake).
In both cases the first wake is unnecessary, so remove it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These channels aren't selectable anyway, but our calculations
for 2.5 mhz frequencies are incorrect. The value is supposed to
be:
(frequency - reference) * (10/25)
i.e., divide by 2.5, but we were instead doing:
(10 * frequency - reference) / 25.
Additionally, the check for (frequency % 5 == 2) had an extra
subtraction that wasn't in madwifi HAL.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2872 needs the same rf register setup as rt3070 and rt3090, hence
use rt2800_config_channel_rt3x instead of rt2800_config_channel_rt2x.
This change allows me to actually switch channels and hence scan all
configured channels on the RT305x SoC platform (which uses a rt2872)
here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't modify ah->iniModes, it's supposed to be constant. Instead, apply
the fixup when the data is written to the registers.
Change ath9k_hw_init_eeprom_fix() to only determine whether the fixup is
needed.
This allows similteneous support for AR9220 cards that need AR_AN_TOP2
fixup (such as Ubiquiti SR71-12) and those that don't need it (D-Link
DWA-552 rev A2).
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Messages that are generated by the HTC layer
don't have any TX callback endpoints assigned to them.
Consequently, the allocated SKBs are never freed.
Fix this issue by handling this case in the HTC layer
itself.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hif_usb_regout_cb() frees the given URB, which is
borked by design. Use an anchor to simplify URB
management.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maximum number of packets in a single buffer in
stream mode is 10. The driver currently uses 8 - which
caused stack corruption, in the absence of any kind
of OOB checking.
Fixing this to the correct value of 10 fixes the module
unload issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX URBs are automatically freed when the reference
count drops to zero - this currently doesn't happen when
usb_kill_anchored_urbs() is called during unload.
Fix this by dropping the reference count by one during
initial submission.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a spin lock to prevent concurrent access
to variables dealing with RX stream mode handling.
Currently, no protection is implemented - which
causes problems in RX.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the powersave issues on rt2500usb have been tackled, powersave
can be enabled by default again.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for a modified newer version of AR9285
chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Better use the macro for consistency, the content is the same anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked
at both ath9k and HAL sources (they are nearly the same), and even though i
have implemented some things differently, the basic algorithm is practically
the same, for now. I hope that this can serve as a clean start to improve the
algorithm later.
This also adds a possibility to manually control ANI settings, right now only
thru a debugfs file:
* set lowest sensitivity (=highest noise immunity):
echo sens-low > /sys/kernel/debug/ath5k/phy0/ani
* set highest sensitivity (=lowest noise immunity):
echo sens-high > /sys/kernel/debug/ath5k/phy0/ani
* automatically control immunity (default):
echo ani-on > /sys/kernel/debug/ath5k/phy0/ani
* to see the parameters in use and watch them change:
cat /sys/kernel/debug/ath5k/phy0/ani
Manually setting sensitivity will turn the automatic control off. You can also
control each of the five immunity parameters (noise immunity, spur immunity,
firstep, ofdm weak signal detection, cck weak signal detection) manually thru
the debugfs file.
This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies tx-queue flushing to correspond with tx-path - i.e.
also frames for which no ack was requested are forwarded to the mac80211
for disposal.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ERROR print from psm-entry-fail scenario, instead use an INFO print.
Also, add INFO print to the beacon-loss scenario.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the fixed listen-interval max value configured to the mac80211 on
driver init. This value will allow a larger value to be configured to the
AP, which means the AP will buffer our frames longer.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure meaningful rates to be used with the templates. For control frames,
use the determined basic rates (currently the lowest rate for the band) and
for data-frames (null-funcs) let the firmware use the current rate policy to
determine the rate.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mac80211 is not telling a hardware rate controlled driver a
rate to use for association frames etc. So to be safe, use the lowest rate
of each band for communication.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware does not like the host configuring the keep-alive after it has
been once configured after a join-operation. Instead, it will complain about
invalid parameters, which do not break functionality, but do not look nice
in the syslog either.
This patch prevents the complaints by only configuring the keep-alive once
for an association, after the first time join is performed with the correct
bssid.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The command header was missing in the wl1271_cmd_disconnect structure. It
was working fine by sheer luck, because the parameters are not critical and
because our wl1271_cmd_send() function was overwriting the rx_config_options
with the actual header.
This patch adds the header to the command structure.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our SPI driver is called "wl1271_spi" in the driver information structure.
Let's use the same for SDIO so that things are aligned.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, this check is invalid.
Remove the check so that new product IDs can be added.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used to store the bus types ( AHB/PCI/USB ).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commits 8e6f5aa250 and
db1a052b73 accidentally introduced
compile errors that happens when ath9k debug is not enabled.
This patch fixes the declaration of the inline stubs to resolve this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->mask_reg was used to hold different data throughout the driver.
ath9k_hw_init_interrupt_masks() used it to save the value written to
AR_IMR. ath9k_hw_set_interrupts() used it to hold the interrupt mask as
defined in enum ath9k_int. Those masks differ in many bits.
Use ah->imask instead of ah->mask_reg in ath9k_hw_set_interrupts() and
ath9k_hw_updatetxtriglevel(). That's what the code was meant to do.
ah->imask is initialized in ath9k_start(), so we don't need to
initialize it from ah->mask_reg.
Once it's done, ah->mask_reg becomes write-only, so it's replaced with a
local variable in ath9k_hw_init_interrupt_masks().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ah variable in the functions that didn't have it and used sc->imask.
Replace sc->sc_ah with ah in those functions.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbols starting with "ATH9K_INT" are also used for interrupt mask.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to files in ath/ar9170 that fixes a set of warnings
found by checkpatch.pl tool. A line over 80 characters, a few empty
spaces before tab and a few empty characters before a new line.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In all drivers ensure that auto wakeup is disabled before waking up the device.
This is needed to prevent connection stability issues and problems in waking up
the device.
Based upon a patch from Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.
Thanks to Alagu Sankar for pointing me in the right direction.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alagu Sankar <alagusankar@embwise.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/regd.c file that fixes two code
readability issues. A space between to separate two defines
and the indentation inside the ath_redg_is_eeprom_valid
function.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/hw.c file that fixes up a warning about
macros found by the checkpatch.pl tool, that said that complex values
should be enclosed in parenthesis.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ralink SoC platforms do not have an MCU.
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Includes minor improvements in debugging messages in iwl-4965.c,
function iwl4965_is_temp_calib_needed().
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some defines used by all agn devices, but the definitions were in
iwl-4965-hw.h, move those to iwl-agn-hw.h which is the better place for
those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In iwl_rx_queue_reset(), we didn't clear the rxq->queue[]. This might
cause the same rxb appears on multiple places in rxq->queue. Although
this won't cause any problem because of the read and write pointers
protection in rxq, we'd better clear it to avoid misleading.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Module parameters used to be defined in both iwl-5000.c and iwl-4965.c,
after the code re-structure, merge into iwl-agn.c for easy to read and
maintenance.
Number of module parameters are deprecated after this merge. These are also
scheduled for removal by 2.6.40.
The current supported parameters are:
parm: debug50:50XX debug output mask (deprecated) (uint)
parm: debug:debug output mask (uint)
parm: swcrypto50:using crypto in software (default 0 [hardware])
(deprecated) (bool)
parm: swcrypto:using crypto in software (default 0 [hardware]) (int)
parm: queues_num50:number of hw queues in 50xx series (deprecated)
(int)
parm: queues_num:number of hw queues. (int)
parm: 11n_disable50:disable 50XX 11n functionality (deprecated) (int)
parm: 11n_disable:disable 11n functionality (int)
parm: amsdu_size_8K50:enable 8K amsdu size in 50XX series (deprecated)
(int)
parm: amsdu_size_8K:enable 8K amsdu size (int)
parm: fw_restart50:restart firmware in case of error (deprecated) (int)
parm: fw_restart:restart firmware in case of error (int)
parm: disable_hw_scan:disable hardware scanning (default 0) (int)
Remove "antenna" module parameter, it is not being used in "agn" driver.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().
To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Henry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
While ar9170's USB transport packet size is currently set to 8KiB,
the PHY is capable of receiving AMPDUs with up to 64KiB.
Such a large frame will be split over several rx URBs and
exceed the previously allocated space for rx stream reconstruction.
This patch increases the buffer size to 64KiB which is
in fact the phy & rx stream designed size limit.
Cc: stable@kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=15591
Reported-by: Christian Mehlis <mehlis@inf.fu-berlin.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 skips drop_unencrypted checks if the driver/firmware has
already taken care of this. In case of ath9k, we must not indicate
that the frame was decrypted if no decryption was actually done.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set IEEE80211_HW_RX_INCLUDES_FCS to indicate that
the FCS is present in RX frames. Also, remove a redundant
assignment of skb length and include the FCS_LEN
when checking padding.
Fixing this issue makes TKIP work.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_status and ath_rx_status data are only necessary for a short
time, until they have been processed and converted into mac80211 data
structures.
Because of that, it makes no sense to keep them tied to the DMA
descriptor, that only wastes precious memory.
This patch allocates the data on stack in the functions that call the
conversion functions from ath9k_hw.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch passes in a pointer to the ath_rx_status data structure for
functions that need it, instead of letting them grab it directly from
the ath_desc struct. This is useful for making it possible to allocate
the intermediate rx status data separately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch passes in a pointer to the ath_tx_status data structure for
functions that need it, instead of letting them grab it directly from
the ath_desc struct. This is useful for making it possible to allocate
the intermediate tx status data separately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan watchdog is fired, try to send abort scan command
first before restarting the adapter. This avoids reconnection for
some users when scan hang is detected.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15419
Reported-by: Maurizio Avogadro <mavoga@gmail.com>
Tested-by: Maurizio Avogadro <mavoga@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not setting the opmode properly during initialization
results in the firmware sending up a bunch of packets
before add_interface() has been called, for the first
interface.
This patch fixes the issue by setting the initial mode
to 'managed'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stop/restart TX queues when the internal SKB
queue is full. This helps handle TX better
under heavy load.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the usage of URB anchors,
thus reducing a large amount of code dealing with
URB maintenance within the driver. The RX callback now
takes care of freeing the SKB associated with each URB.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip beyond the watchdog pattern properly.
This fixes occasional failure of the driver to load.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing the sta pointer in TX completion without
approprate RCU protection is wrong. Fix this.
Also, RCU protection is needed when the station's
aggregation state is updated. Handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculation of RX filter is fairly different
between ath9k and ath9k_htc, trying to make this
common between the two drivers would result in code churn.
While at it, remove the handling of PSPOLL filter,
it can be added when(if) AP support is added to ath9k_htc.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We activate/deactivate QoS and setup default queue parameters in iwlwifi
driver. Mac stack do the same, so we do not need repeat that work here.
Stack also will tell when disable QoS, this will fix driver when working
with older APs, that do not have QoS implemented.
Patch make "force = true" in iwl_active_qos() assuming we always want
to do with QoS what mac stack wish.
Patch also remove unused qos_cap bits, do not initialize qos_active = 0,
as we have it initialized to zero by kzalloc.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove skb_linearize() in the iwlwifi drivers since
mac80211 supports paged rx SKBs now.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to partially change chanspec just to find out there is not
entry in table for given channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Taken from latest ralink linux driver(RT3070_LinuxSTA_V2.3.0.1_20100208)
All of them are RT3070 devices.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Taken from latest ralink linux driver, it's a RT3593 PCI/PCIe.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was removed in the windows inf file by ralink.
And it isn't on ralink linux drivers.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After last transmission, the device goes to sleep earlier
than the configured dynamic power save timeout. If timeout
is set to 400ms, device enters into sleep mode at around
330ms since from last TX.
This patch removes the msleep(1), which causes the delay
after ELP wakeup. Replaced with udelay(10), the variation
is around 7-10ms.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will enable the hardware keep-alive mode, configure the required
template, configure keep-alive parameters, and re-order JOIN's and ACX_AID
in such a way that the keep-alive is activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for keep-alive templates, which are indexed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures the mac80211 to not perform connection monitoring
(periodic probe-requests) and instead rely on the hardware to do it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If PSM entry fails despite of retries, assume that the AP has been lost,
and indicate connection loss to the mac80211. This is much safer than
remaining in active mode.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure a probe-request template to the wl1271 when associated - the
wl1271 will use this to attempt to recover a connection when beacon loss
is detected.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver tx-queue flush operation leaks broadcast-frames. This leak occurs
if the driver is shut down while there are frames in TX buffers (such as in
a firmware crash scenario.) Fix the leak.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the driver to call ieee80211_beacon_loss function always when
BSS_LOST_EVENT is received. Reason for the change is that entering PSM
might fail before driver receives BSS_LOST_EVENT. In such case the
driver would disable PSM and the stack would not be notified about beacon
loss and connection loss detection would be delayed by tens of seconds.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the hardware beacon interval to whatever requested by the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the driver to better reflect the ad-hoc related configuration from the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 does not support disabling the connection monitor feature.
Perform the next best thing by increasing the beacon-loss threshold and
BSS_LOSE event timeout to the maximum values.
This is needed, because we really don't want any random probe-requests during
scanning or especially while in ad-hoc mode and not beaconing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise element in the ieee80211_rx_status struct has been deprecated in
commit "mac80211: deprecate RX status noise". Remove the usage of this
element from wl1271_rx.c to avoid warnings.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wait for the DISCONNECT_EVENT_COMPLETE_ID event after sending a disconnect
command.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Poll for join command completion instead of waiting blindly for 10 msecs.
There is a timeout of 100 msecs, if the command doesn't complete by then, we
return an error code.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the MAC address randomization from the driver. This removes
a nasty Nokia-OUI dependency from the driver.
With this patch, unless an address is explicitly configured to the driver
by the user, only a zero address will be configured, and the driver will be
unable to start.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the busy-words, if the firmware did not complete by the end of the
first (fixed) busy-word, a flip of the CS line is required to enable clocking
out the actual read data.
This patch changes the mechanism such that the CS line is flipped after each
busyword.
Also, the busy-word mechanism is finally enabled, and the number of fixed
busywords reduced to the minimum.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a trivial memory leak in cmd_data_path.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were wrong format specifiers in wl1271_sdio.c in some debug
outputs. This has been causing warnings on some platforms.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures the wl1271 chipset clock-request line to be
driver in open-drain mode instead of push-pull.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak in the scan command handling code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two memory leaks in the SPI initialization code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add reporting of the used TX rate to mac80211 in the tx_status.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the code to convert a firmware rate class index into an index
for the rate configuration table.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When forward porting some patches to upstream, there was a mistake and the
wl1271_spi driver name remained, erroneously, as "wl1271". This patch fixes
that.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chipsets since revision AR5213A (0x59) have hardware counters for PHY errors
which we can read directly from the registers. Older hardware has to use the RX
descriptor status to get a count of PHY errors. This will be used in several
places in the ANI implementation, so a flag is useful.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PHY error codes from the HAL, and keep them in statistics for debugging
via the 'frameerrors' file. This will also be used by ANI.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let's keep MIB counter statistics in our own statistics structure and only
convert it to ieee80211_low_level_stats when needed by mac80211. Also we don't
need to read profile count registers in the MIB interrupt (they don't trigger
MIB interrupts).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize noise floor variable with a default of -95. This was used
uninitialized in the signal strength (RSSI -> dBm) conversion until the first
noise floor calibration was completed.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keep an exponentially weighted moving average of the beacon RSSI in our BSS.
It will be used by the ANI implementation.
The averaging algorithm is copied from rt2x00, Thanks :)
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not a phy related funtion; It has more to do with the interrupt handler
and tasklet scheduling, so it belongs to base.c.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Optimize ath5k_hw_calibration_poll() since it is called on every singe
interrupt.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need to generate a software interrupt (SWI) just to schedule a tasklet
- we can just schedule the tasklet directly.
Rename constants, names, etc to reflect the fact that we don't use SWI any more.
Also move the flag handling into the tasklet and prepare it to behave correctly
when there are multiple flags present.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove static variable ath5k_calinterval which was used as a constant. Use a
#define instead. Also we don't need ah_cal_intval.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.
IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.
rates = kzalloc((sizeof(struct ieee80211_rate) * IWL_RATE_COUNT_LEGACY),
GFP_KERNEL);
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: stable@kernel.org
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An int urb is constructed but we fill it in with a bulk pipe type.
Commit f661c6f8c6 implemented a pipe type
check when CONFIG_USB_DEBUG is enabled. The check failed for all the ar9170
usb transfers and the driver could not configure the wifi dongle.
This went unnoticed until now because most people don't have
CONFIG_USB_DEBUG enabled.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Stable <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent bug reports have shown that rt2500usb also suffers from the
powersave problems that the PCI rt2x00 drivers suffer from.
So disable powersaving by default for rt2500usb as well.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously in interrupt handling tasklet, iwlwifi driver only clear/ack
those interrupts that are enabled by the driver through inta_mask.
If the hardware generates unattended interrupts, driver will not ack them,
defeating the interrupt coalescing feature. This results in high number
of interrupts per second and high CPU utilization.
This patch addresses this issue by acking those unattended interrupts
in the tasklet. Local test showed an order of magnitude improvement
in terms of the number of interrupts without sacrificing networking
throughput. This is a workaround for hardware issue.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Forget one hunk in 4965 during "iwlwifi: error checking for number of tfds
in queue" patch.
Reported-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Thanks to Chris Chabot for giving his old wireless usb dongle to me
to test it under Linux.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the NEC WL300NU-G USB wifi dongle.
Signed-off-by: Ben Konrath <ben@bagu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid checking for specified device type to perform certain function,
switch to .cfg approach as more generic and better implementation
method.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Use spin_lock_irqsave() in interrupt handler to disable interrupts locally
and provide the spinlock on SMP. This covers both interrupt and SMP
concurrency.
With this changes, also fix the sparse warning issues.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Remove the "\n" from following module parameter description:
- enable wifi/bluetooth co-exist
- led mode: 0=blinking, 1=On(RF On)/Off(RF Off), (default 0)
to be consistence with the rest of iwlagn/iwlcore module parameters format.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In stead of checking for 4965 and do KELVIN_TO_CELSIUS conversation, add
.cfg parameter for more generic approach.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We go to great lengths to calculate this value
that is never used by mac80211. Additionally,
it is now deprecated by mac80211 and is causing
driver compilation to give warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
After re-structure the agn files layout and move all the
agn shared functions out from iwl-5000.c, all those functions and data
structures do not need to be declare "extern" from iwl-5000.c in
iwl-dev.h.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move more functions only used by agn driver from iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Identify the rx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Identify the tx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
agn module parameter data structure shared by all agn devices, move it
iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Each device has it own eeprom, so the tx power version could be
different, define TX_POWER_VERSION per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices share the same common functions.
Move those functions from iwl-5000.c to iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
uCode alive for iwlagn based devices share the same functions.
Move those functions from iwl-5000.c to iwl-agn-ucode.c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hw definitions.
Move device hardware related defines from iwl-5000-hw.h to iwl-agn-hw.h
file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same tansmit queue functions.
Move tx queue related code from iwl-5000.c to iwl-agn-tx.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hcmd related functions.
Move from iwl-5000.c to iwl-agn-hcmd.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Loading uCode functions are shared across multiple agn devices.
Move those functions to iwl-agn-ucode.c file with other uCode
related functions.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same ucode loading procedure.
Move loading related code from iwl-5000.c to iwl-agn-ucode.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_good_ack_health() check for expected and actual ack count which only
apply to aggregation mode. Move the function to iwlagn module.
Reported-by: Chantry Xavier <chantry.xavier@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This reverts commit 76232ebf89.
iwl_good_ack_health only applies to aggregation and thus only to iwlagn. We
can thus move the function to iwlagn instead of modifying compile flags.
This is done in following patch.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_good_ack_health':
drivers/net/wireless/iwlwifi/iwl-rx.c:647: error: 'struct iwl_priv' has no member named '_agn'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto auth mode is enabled by default. If user doesn't specify the
auth mode, while association driver will first try with open mode
and then with shared key mode. If user specifies an auth mode,
auto auth is disabled and driver will not try association with
another auth mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Daniel Ngu <daniel.dy.ngu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change local functions that are cast to iw_handler to
the more standard use with "union iwreq_data *wrqu"
so the iw_handler array no longer needs the casts.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert direct uses of [ (foo - SIOCIWFIRST) , fn)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed platform_device to be allocated dynamically from the
wl1271_alloc_hw function. Also cleaned up error handling in the
wl1271_alloc_hw function and module probe functions.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing the wl1271 from the inet addr notifier chain sometimes causes the
registered handler to be called - causing locking problems if the removing
function is called from within the mutex.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The null func template is not needed for ad-hoc, and it's generation is not
supported for ad-hoc (mac80211 will WARN about it.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the filters configured by the mac80211 stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed duplicate code from wl1271_sdio module remove function. For
freeing stuff in the remove function wl1271_free_hw function is now
used.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added separate flag for SDIO debugging. Previously it has used
DEBUG_SPI flag. This patch also includes couple indentation fixes.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's no longer needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes MAC address handling. To achieve this, firmware booting had
to be delayed from the previous op_start to op_add_interface, which is the point
when the driver gets to know the configured MAC address. As the wl1271 only
supports one virtual interface, this even seems quite logical.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271 supports U-APSD similarly as wl1251, so let's enable it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "wl1271: implement WMM" accidentally used CONF_PS_SCHEME_LEGACY_PSPOLL,
but instead CONF_PS_SCHEME_LEGACY should be used as earlier.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for U-APSD.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we get probe request from mac80211, we can remove two functions.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 now can create pspoll and nullfunc templates, better to use those.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everything is ready now and we can enable WMM in wl1271.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a sysfs file to control the state of the BT co-ex (enable or disable it.)
By default, the BT co-ex is enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to get the platform device for both SPI and SDIO, move the platform
device registration to wl1271_main.c from wl1271_spi.c.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add configuration values for the varous WLAN-BT co-ex configuration parameters,
and finally enable WLAN-BT co-ex. Based on preliminary measurements, it
appears the co-ex feature is not increasing WLAN power consumption, if BT
is not activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bluetooth coexistence (SG) configuration messages have changed and
were completely wrong. For instance, intending to enable the SG, it was
instead disabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed driver to keep MMC host claimed while wlan interface is up.
This keeps MMC stack from powering the SDIO device down.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added method for wlan power control to io_ops struct and moved
wl1271_power_on and wl1271_power_off functions to wl1271_io.h.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The per-queue TX opportunity value is configured by the mac80211 in units
of 32us. The firmware however wants it in us, so add the conversion.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this you will get a panic if the device initialization
fails. Also, free ath_hw instance properly. ath9k_hw_deinit()
shouldn't do it.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9271 needs a full reset only upon the first reset, add
a call for the driver to enable these special resets. We
can optimize this out later without an export.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initializing the PLL on AR9271 we always need
to set the core clock to 117MHz. While at it remove
the baud rate settings for the serial device on the
AR9271, the default settings work well unless you
want to customize it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Periodic power amplifier offset calibration is skipped on ath9k
algorithmically, this is required on AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noisefloor values read on AR9271 are unreliable if they
are less than -114, set those statically to -116.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noisefloor calibration involves querying hardware for samples
and storing this information on a history buffer in hardware for
actual noisefloor calibration processing in hardware. The history
buffer supports collecting information for all Atheros hardware,
one history buffer slot for each chain on each channel used for
MIMO operation. For current hardware this means one history
buffer slot for each chain on both the control (or primary) channel
and the extension (or secondary) channel. We know which noisefloor
registers to poke for collecting noisefloor data through the
chainmask.
For AR9285 and AR9271 devices, both 1x1, the chaimmask is defined as
0x9 = 0b0001001. The first four bits represent each chain out of
a maximum of 4 chains [0-3] on the primary channel. The last four
bits represent each chain on the extension channel. A chainmask
of 0x9 therefore indicates chain 1 is active on both the primary
and the extension channel.
AR9271 only requires collecting and storing noisefloor history buffer
data for the first chain on both the control and extension channel
(nfarray[0] and nfarray[3]) so fix the code and avoid which reads
and writes to the history buffer for the other chains.
Since the noisefloor varies depending on the number of chains your
device supports also initialize the noisefloor history buffer with
reasonable values seen on 1x1 devices such as AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After telling the AR9271 to go into full sleep we do not need
to clear the RTC reset signal.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX descriptors setup for AR971 requires the same
setup as AR9285, so use that.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip test is not required for AR9271 on the host driver
code as the firmware will do the test internally on its own.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the proper number of GPIO pins for AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the register initialization values for AR9271.
This is based on our last review from our systems team.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From e74b075cdb143d45be9b371ee8a8e2dcfc15ab34 Mon Sep 17 00:00:00 2001
From: Ming Lei <tom.leiming@gmail.com>
Date: Sat, 27 Feb 2010 23:50:54 +0800
Subject: [PATCH] ath9k: decrease size of ath9k.ko
The patch defines the fields of 'valid_single_stream' and 'valid' in
struct ath_rate_table as char type, so decrease the size of ath9k.ko
about 2KB.
old ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
69344 3080 168 72592 11b90 ath9k.ko
new ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
67304 3080 168 70552 11398 ath9k.ko
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the connectivity check and recovery routine into separated
functions based on the types
1. iwl_good_ack_health() - check for ack count
2. iwl_good_plcp_health() - check for plcp error
Based on the type of errors being detected, different recovery methods
will be used to bring the system back to normal operational state.
Because different NIC has different HW and uCode, the behavior is also
different; these functions thus now form part of the ops infrastructure,
so we can have more control on how to monitor and recover from error condition
case per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the
expected_ack_count also drops. At the same time, the aggregated
ba_timeout (the number of ba timeout retries) also rises. If the
actual_ack_count/expected_ack_count ratio is 0 and the number of ba
timeout retries rises to BA_TIMEOUT_MAX, no tx packets can be delivered.
Reloading the uCode and bring the system back to normal operational
state.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the plcp error checking into stand alone function and pointed by ops
to accommodate devices not needing this recovery.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the internal TX queues periodically. When a queue is stuck
for some unknown conditions causing the throughput to drop and the
transfer is stop, the driver will force firmware reload and bring the
system back to normal operational state.
The iwlwifi devices behave differently in this regard so this feature is
made part of the ops infrastructure so we can have more control on how to
monitor and recover from tx queue stall case per device.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Align the driver names with official product names for 1000/5000/6000
series. This change mainly affects the debug messages show up in system
log. No functional changes.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The only caller of this is iwl_rs_rate_init
which is only called with a valid sta_id.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 recently implemented two new callbacks that are used to request
station add/remove from the driver. The benefot from these new callbacks
are that they enable the driver to sleep while performing this work.
This is a big patch since a few things need to be coordinated in this move.
First we need to decouple station management from rate scaling, which
caused a lot of code to be moved and/or deleted. Next we needed to tie in
with mac80211's station management callback and let it direct our station
management as well as trigger the rate scaling initialization.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently the broadcast station is added after every RXON command. Change
this to only add the broadcast station when interface is added by mac80211.
With this we need some extra work to ensure broadcast station is always
present since station table is cleared when RXON without ASSOC bit set is
sent. To deal with this we re-add all driver known stations to uCode after
such an RXON command is sent.
We also do some cleanup and remove the various calls to clear the station
table. We now only clear the station table in two scenarios:
- only clear uCode portion of station table when RXON command without ASSOC
bit is sent
- clear uCode and driver portion when interface goes down or is removed.
We need to do this clearing when interface goes down to deal with the
device restart/reconfigure routines which do not remove the interface, but
do add the interface during reconfiguration.
Previously the keys were also cleared when station table in driver is
cleared, this is not done anymore since mac80211 will take care that keys
are set and cleared correctly.
There is a known issue with this change. Associating with different AP
without bringing interface down fails with a firmware error. This is
because of the lack of full station notification support and the later
patches in this series that complete the station notification support will
fix this.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
FH register dump debug feature was recently added for 5000 and later;
4965 can use it also.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Commit a239a8b47c introduced a
noisy message, that fills up the log very fast.
The error seems not to be fatal (the connection is stable and
performance is ok), so make it IWL_DEBUG_TX rather than IWL_ERR.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable@kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I initially stumbled upon sequence number problems with PAE frames
in ath9k, I submitted a patch to remove all special cases for PAE
frames and let them go through the normal transmit path.
Out of concern about crypto incompatibility issues, this change was
merged instead:
commit 6c8afef551
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Tue Feb 9 10:07:00 2010 +0530
ath9k: Fix sequence numbers for PAE frames
After a lot of testing, I'm able to reliably trigger a driver crash on
rekeying with current versions with this change in place.
It seems that the driver does not support sending out regular MPDUs with
the same TID while an A-MPDU session is active.
This leads to duplicate entries in the TID Tx buffer, which hits the
following BUG_ON in ath_tx_addto_baw():
index = ATH_BA_INDEX(tid->seq_start, bf->bf_seqno);
cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
BUG_ON(tid->tx_buf[cindex] != NULL);
I believe until we actually have a reproducible case of an
incompatibility with another AP using no PAE special cases, we should
simply get rid of this mess.
This patch completely fixes my crash issues in STA mode and makes it
stay connected without throughput drops or connectivity issues even
when the AP is configured to a very short group rekey interval.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case debugfs does not init for some reason (or is disabled
on older kernels) driver does not allocate stats.fw_stats
structure, but tries to clear it later and trips on a NULL
pointer:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
PC is at __memzero+0x24/0x80
Backtrace:
[<bf0ddb88>] (wl1251_debugfs_reset+0x0/0x30 [wl1251])
[<bf0d6a2c>] (wl1251_op_stop+0x0/0x12c [wl1251])
[<bf0bc228>] (ieee80211_stop_device+0x0/0x74 [mac80211])
[<bf0b0d10>] (ieee80211_stop+0x0/0x4ac [mac80211])
[<c02deeac>] (dev_close+0x0/0xb4)
[<c02deac0>] (dev_change_flags+0x0/0x184)
[<c031f478>] (devinet_ioctl+0x0/0x704)
[<c0320720>] (inet_ioctl+0x0/0x100)
Add a NULL pointer check to fix this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After testing, we found that TX_STA_FIFO_MCS is the last MCS value
tried. If the transmission failed, 8 frames have been transmitted. If the
transmission succeed, we can easily compute the number of retry. This patch fix
the way status is reported to mac80211 rate control. It has 2 bugs :
1. mcs can contain the short preamble flag and it will lead to wrong
computations.
2. minstrel nearly always say that 54 Mbits is the best rate, even if we are
very far from the AP
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an implementation that support WCID being the encryption key.
Wireless Cli Id was set to be the encryption key in rt2800pci_write_tx_desc
and read (TX_STA_FIFO_WCID) as the current queue entry index.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix compile warning "rt2800pci.c:1248: warning: 'rt2800pci_device_table'
defined but not used" when building rt2800pci with only soc support
(without pci).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ieee80211" was the old name of the common library for ipw2100 and
ipw2200. It was renamed to "libipw", but some occurrences of the old
name remained.
Rename alloc_ieee80211() to alloc_libipw() and free_ieee80211() to
free_libipw(). Adjust comments and label names. Change prefixes in
diagnostic messages.
Keep /proc/net/ieee80211 under the original name to avoid breaking user
interface.
Move the affected EXPORT_SYMBOL macros to their proper places.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hostap driver provides better support for Prism chipset.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
4sec wait is way too pessimistic, TI driver uses 40ms here,
and testing shows that is ebough, so let's also use that.
While at it, add useful sounding comment from the TI driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some unknown reason ELP_CTRL can't be accesed using
sdio_memcpy_* functions (any attemts to do so result in timeouts):
wl1251: ERROR sdio write failed (-110)
wl1251: ERROR sdio read failed (-110)
wl1251: WARNING WLAN not ready
To fix this, add special IO functions for ELP_CTRL access that are
using sdio_readb/sdio_writeb. Similar handling is done in TI
reference driver from Android code drop.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make local functions and data static, also constify
some structures. While at it, clean up unneeded includes.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code was commented-out when it was added about a year ago and
remains unchanged -- seems as if we don't need it...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath5k: remove stale function declarations, make some functions static"
commented-out some unused functions. This removes them.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
For the firmware version 5.30.17 the log file shows:
Firmware version 5.30.11
The variable softSubVer is binary.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some status, reason is encoded in the low byte, but airo_print_status forgot tp mask low byte in status parsing.
This make it only work when reason is 0.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate control algorithm, default is Minstrel for ath5k, determines
the number of retries to use for each rate. However, there exists in
ath5k_hw_setup_4word_tx_desc (which is called for AR5212 like devices)
a set number of retries defined by AR5K_TUNE_HWTXTRIES. The set
number of tries is added to the tx_tries0 variable setup by the rate
control algorithm. This changes the number of retries the rate
control algorithm considers necessary. By removing the
AR5K_TUNE_HWTXTRIES from the retry calculation the rate control
algorithm is given control over the number of retries.
Signed-off-by: Andrew Blaich <ablaich@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the rate control tx status update gets called for every
subframe of an A-MPDU, and ath9k marks the frame with the relevant
status update with an internal flag. This not suitable for rate control
algorithms using the standard mac80211 rate control API, so fix this by
using IEEE80211_TX_STAT_AMPDU for marking the correct frames that
should be processed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As wl1271_sdio implementation depends on ARM GPIO impelementation it is
not directly usable on other architectures at the moment. Added
ARM dependency to kernel configuration option.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here are some minor updates for EEPROM, mostly documentation and some small
fixes which have no effect at the moment.
- fixed_bias is not available for B mode.
- AR5K_EEPROM_[RT]X_CHAIN_DIS is 3 bit. this is MIMO and will not be used in
ath5k, but just to be correct.
- AR5K_EEPROM_JAP_MID_EN added, and shift of following flags adapted.
- added some documentation for EEPROM values and some comments.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
according to the HAL sources the calculation of the Q value is slightly
different for AR5211 chips.
i couldn't test this since IQ calibration never finishes on older parts. this
is a different problem...
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add a debugfs file to see different RX and TX errors as reported in our status
descriptors. this can help to diagnose driver problems.
statistics can be cleared by writing 'clear' into the frameerrors file.
example:
# cat /sys/kernel/debug/ath5k/phy0/frameerrors
RX
---------------------
CRC 27 (11%)
PHY 3 (1%)
FIFO 0 (0%)
decrypt 0 (0%)
MIC 0 (0%)
process 0 (0%)
jumbo 0 (0%)
[RX all 245]
TX
---------------------
retry 2 (9%)
FIFO 0 (0%)
filter 0 (0%)
[TX all 21]
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
it's never used and we have a newer implementation in gpio.c.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
it's not used, and we have ah_mac_srev.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
it's never used. probably a leftover from the old OpenHAL days...
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
opmode (operating mode) was defined in struct ath5k_hw and struct ath5k_softc.
remove it from ath5k_hw and use only from ath5k_softc (sc->opmode).
(btw: what's the meaning of opmode when we have multiple interfaces?)
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
save antenna settings and preserve across resets.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
keep statistics about which antenna was used for TX and RX. this is used only
for debugging right now, but might have other applications later.
add a new file 'antenna' in debugfs (/sys/kernel/debug/ath5k/phy0/antenna) to show
antenna use statistics and antenna diversity related register values. it can
also be used to set the antenna mode until we have proper support for that in
iw:
- echo diversity > antenna: use default antenna mode (RX and TX diversity)
- echo fixed-a > antenna: use fixed antenna A for RX and TX
- echo fixed-b > antenna: use fixed antenna B for RX and TX
- echo clear > antenna: reset antenna statistics
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for cfg80211 set_pmksa/del_pmksa/flush_pmksa. Updating PMKID
entry list is done on driver side since NDIS API requires full list update.
v2:
- fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
- fixed false padding from struct ndis_80211_bssid_info
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend rndis_wlan_get_caps() to get 802.11 capabilities and maximum
supported number of PMKIDs by device.
v2: fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some variables were left unused after cfg80211 conversion. Remove those and related deadcode.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_query_oid() uses full output buffer size to copy response buffer
from rndis_command()/device. This doesn't cause problems as response buffer
is sized based on output buffer but does copy extra unset bytes.
So change rndis_query_oid() so that only meaningful bytes are being copied.
Also in case of malfunctioning device/cable/etc returned data offset from
device might be wrong so bound check memory access correctly, so add
checks for this.
v2: fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the padding position is based on
ieee80211_get_hdrlen_from_skb(). This is not correct since the HW does
padding on RX (and expect the same padding to be present on TX) at the
following position :
- management : 24 + 6 if 4-addr format
- control : 24 + 6 if 4-addr format
- data : 24 + 6 if 4-addr format + 2 if QoS
- invalid : 24 + 6 if 4-addr format
whereas ieee80211_get_hdrlen_from_skb() is :
- management : 24
- control : 16 except for ACK/CTS where it is 10
- data : 24 + 6 if 4-addr format + 2 if QoS + 2 if QoS & order
- invalid : 24
So, correct frames are not affected : management frames do not use
4-addr format, control frames have no body and invalid frames are ...
not valid by definition. However, in order to use monitor interface for
debugging purpose, one must be able to send/receive any frames, be it
correct or not. Such frames are affected by incorrect padding.
Moreover, since padding is added on TX, we need to remove it before
calling ieee80211_tx_status. This affect TX packets received by monitor
interfaces.
It has been tested between an ath5k based card (AR5212) and an ar9170usb
based card (netgear WNDA3100) using a frame generator and a monitor
interface for each card.
v2: Added ath5k_add_padding / ath5k_remove_padding
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix wrong IWM_RX_TICKET_DROP_REASON_MSK macro define, typo and other
small cleanups.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase concatenated buffer from 8K to 32K to get better performance.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Protect rx_tickets and rx_packets[] lists with spinlocks to fix the
race condition for concurrent list operations. In iwmc3200wifi both
sdio_isr_worker and rx_worker workqueues can access the rx ticket
and packets lists at the same time under high rx load.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add event tracer for iwmc3200wifi driver. When enabled, all the
commands and responses between the driver and firmware (also
including Tx/Rx frames) will be recorded in the ftrace ring buffer.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use list_for_each_entry instead of list_for_each_entry_safe in
places iteration against list entry removal is not required.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to make sure we don't associate with APs on unallowed
channels (according to regulatory setting). This could happen
when the channel is not specified (auto-select) within the
connection request. In this case we get the AP's channel until
the firmware indicates the association succeeded later. We need
to verify the associated channel. If the channel is disabled by
regulatory, we have to disassociate with the AP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed below compiler warning:
drivers/net/wireless/ipw2x00/ipw2200.c: In function ‘ipw_load_firmware’:
drivers/net/wireless/ipw2x00/ipw2200.c:3260: warning: the frame size of
1168 bytes is larger than 1024 bytes
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we read the IQ correction values (i_cal and q_cal) for G mode from a wrong
location (the same shifts as for A mode is applied which is incorrect). use
correct locations, matching the docs and HAL sources.
also we should write IQ correction only when we have that information in the
EEPROM, starting from version 4. also write it in the same way as we do in the
periodic recalibration (enable last), just to be sure.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.
1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd0f)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.
2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.
3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.
4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: stable@kernel.org
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a
function for that so use it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when using a fixed antenna we should use the antenna number in all tx
descriptors, otherwise the hardware will sometimes send the frame out on the
other antenna. it seems like the hardware does not always respect the default
antenna and diversity settings (esp. AR5K_STA_ID1_DEFAULT_ANTENNA).
also i would like to note that antenna diversity does not always work correctly
on 5414 (at least) when only one antenna is connected: for example all frames
might be received on antenna A but still the HW tries to send on antenna B some
times, causing packet loss.
this is both verified with the antenna statistics output of the previous patch
and a spectrum analyzer.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee->networks consists of 128 struct libipw_network entries. If
we allocate this chunk of memory altogether, it ends up with an
order 4 page allocation. High order page allocation is likely to fail
on system high load. This patch splits the big chunk memory allocation
into small pieces, each is 344 bytes, allocates them with 128 times.
The patch fixed bug http://bugzilla.kernel.org/show_bug.cgi?id=14989
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the KSEG1ADDR define from rt2x00soc.h as it redefines and covers the
correct one from the arch/mips/include/asm/addrspace.h. Otherwise the driver
oopses on the target platform (Ralink rt3050 board).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 21b2d8bd2f.
As explained by Johannes:
When we
build a probe request frame in the buffer with the SSID, we could
arrive over the limit of 200 bytes. When we build it in the buffer
without the SSID (wildcard) we don't arrive over 200 bytes, but the
ucode still allows direct probe in addition because it has an internal
buffer that is larger when it inserts the SSID...
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Recent patch "iwlwifi: move 3945 clip groups to 3945 data" exposed a memory
corruption problem. When initializing the clip groups the code was
mistakenly using the iwlagn rate count, not the 3945 rate count. This
resulted in more memory being written than was allocated.
"iwlwifi: move 3945 clip groups to 3945 data" moved the location where the
clip groups are stored and the impact is now severe in that the number of
configured TX queues is modified. Previously the
"temperature" field was overwritten, which did not seem to affect the
operation.
Fix this one instance where wrong rate count was used. I also noticed one
more location where the iwlagn rate count was used to index an iwl3945
array, fix this. I also modified one location that modified the iwlagn rate
count to obtain the iwl3945 rate count ... just use the iwl3945 rate count
directly.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2165 and
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2168
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Check successful completion of BSM loading. Give a chance to
load BSM again. If BSM loading is unsuccessful we should exit
and not initilize NIC. Before this checking even if the BSM loading failed
driver tries to initilize the NIC which should not be the case.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
4965 hardware has 7 queues reserved and the
remaining ones used for aggregation, 5000
and higher need to have 10 reserved. This
is not very clear in the code right now,
unfortunately.
Introduce a new IWL_TX_FIFO_UNUSED constant
and make the queue/FIFO mapping arrays able
to hold that value, and change the setup
code to reserve all queues in the arrays
(the queue number is the index) and use the
new unused constant to not map those queues
to any FIFO.
Additionally, clear up the AC/queue mapping
code to be more understandable. The mapping
is the identity mapping right now, but with
the mapping function I think it's easier to
understand what happens there.
Finally, HCCA isn't implemented at all and
I think newer microcode removed it, so let's
remove all mention of it in the code, some
comments remain for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add internal short scan support for 3945 NIC, This allows 3945 NIC
to support radio reset request like the other series of NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small change to remove unnecessary "ret" parameter since it not being
used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"internal_scan" debugfs function serves the same propose of mode "0" of
"force_reset" debugfs function. Remove it to avoid duplicate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_apm_stop_master and iwl_internal_short_hw_scan
are only used within iwlcore and thus do not need to be exported.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For later station notification support we would like WEP key setting to be
done synchronously always. Currently all places from which WEP key is set
can sleep, but the usage of sta_lock prevents it to do so. Modify the
locking to use priv->mutex instead and thus enable this call to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small code cleanup to remove un-necessary parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
These files are incompatible with some changes
I'm making, and don't really belong into sysfs
anyway as they can only be used for debugging.
Since writing them will probably crash the
firmware, keep only the reading part and move
them into debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since rfkill integration, mac80211 can no
longer add an interface while the hardware
is not ready, so STATUS_MODE_PENDING can
never be set.
Also, remove another superfluous channel
sanity check and return the commit_rxon
return value in case it failed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This code will never trigger, because when
we call this during interface start, neither
priv->vif nor priv->iw_mode conditions will
be true, and when it happens during reset
then priv->vif is also NULL. Also, in both
cases the same code will be executed as part
of iwl_bss_info_changed(), which contains a
copy of this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Only used on 3945, so it can be in the
3945-specific part of the data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Not all queues are mapped for frame transmission,
so saying "AC" is misleading. They are all mapped
to FIFOs, obviously, though, so use that term and
also say AC/CMD instead of just AC for the queue
type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_mac_beacon_update can only be called
when the operating mode is IBSS, so it
doesn't need to verify that again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will always enforce using a channel
that the driver allowed for IBSS use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This variable is assigned a default value,
but then assigned zero as soon as mac80211
calls a change channel (which will happen
right after the hw is started) and after
that it never changes again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With some of the new code in mac80211, public action
frames can be exchanged as non-injected frames even
while not associated.
Aside from that, dropping frames here is pointless
since we do deal with arbitrary frames that were
injected already, so let mac80211 make the decision
about which frames to allow or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_mac_reset_tsf will only ever be called in
IBSS mode, so checking for other modes is not
useful and the code that depends on that will
not be executed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will not allow using channels not
marked as allowing IBSS for IBSS mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Updating the variables last_rx_rssi, last_tsf
and last_beacon_time needs a lot of code but
they are not actually used in iwlagn (only in
3945) so we can move them to the 3945 specific
data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since the ICT data is all AGN specific, it can
be the first data to create the _agn part of the
device-specific union in the priv struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
To be obviously correct, this patch only modifies
3945 files and the struct definition. A follow-up
patch will create the AGN part of the union.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
All the ICT ISR code is iwlagn specific, and doesn't
need to be in iwlcore. So create a new iwl-agn.h
header file that will hold agn specific function
declarations etc., and move the ICT code into a new
iwl-agn-ict.c file that is linked into iwlagn. This
also gets rid of exporting those symbols.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The AR_IMR_S2 register sometimes cannot be read correctly. Instead of a
valid value, 0xdeadbeef is returned. The driver has been observed
writing that value back to AR_IMR_S2 after changing a few bits.
Cache the register value in ah->imrs2_reg and always write chached value
to the register.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the workaround limiting chipset TX power to 12dB, instead
using the value configured by the mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable host TX rate control. The wl1271 firmware is already managing rate
control, so this eliminate unnecessary host processing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of managing the TX security sequence number as two variables, use
one 64 bit variable. This greatly simplifies the handling of the number.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the required block count calculation. Though it
introduces a division operator, it greatly simplifies the formula.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses a higher precision timer to synchronize with the firmware
clock. Improved precision is needed as on some platforms a jiffy may be up to
tens of milliseconds, and the required precision is closer to TU's.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements looped IRQ handling. In essence, if a new interrupt is
asserted by the FW while the host is processing the previous one, the host
will directly proceed processing the new IRQ without leaving the handling
function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mask firmware interrupts while processing interrupts. This allows the
interrupt handler looping to work efficiently thus reducing interrupt
processing latency.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will ack RX frames read from the firmware in one single write,
instead of acking all the frames separately. This will reduce the amount of
required communication per frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen