Support also transmitting frames using the custom "8899 A"
4 byte tag.
Qingfang came up with the solution: we need to pad the
ethernet frame to 60 bytes using eth_skb_pad(), then the
switch will happily accept frames with custom tags.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: efd7fe68f0 ("net: dsa: tag_rtl4_a: Implement Realtek 4 byte A tag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Hancock says:
====================
Broadcom PHY driver updates
Updates to the Broadcom PHY driver related to use with copper SFP modules.
Changed since v3:
-fixed kerneldoc error
Changed since v2:
-Create flag for PHY on SFP module and use that rather than accessing
attached_dev directly in PHY driver
Changed since v1:
-Reversed conditional to reduce indentation
-Added missing setting of MII_BCM54XX_AUXCTL_MISC_WREN in
MII_BCM54XX_AUXCTL_SHDWSEL_MISC register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm54xx_config_init was modifying the PHY LED configuration to enable link
and activity indications. However, some SFP modules (such as Bel-Fuse
SFP-1GBT-06) have no LEDs but use the LED outputs to control the SFP LOS
signal, and modifying the LED settings will cause the LOS output to
malfunction. Skip this configuration for PHYs which are bound to an SFP
bus.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag and helper function to indicate that a PHY device is part of
an SFP module, which is set on attach. This can be used by PHY drivers
to handle SFP-specific quirks or behavior.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On cpu architectures w/o dma cache snooping, dma_unmap() is a
is a very expensive operation, because its resulting sync
needs to invalidate cpu caches.
Increase efficiency/performance by syncing only those sections
of the lan743x's rx ring buffers that are actually in use.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers in the lan743x driver's receive ring are always 9K,
even when the largest packet that can be received (the mtu) is
much smaller. This performs particularly badly on cpu archs
without dma cache snooping (such as ARM): each received packet
results in a 9K dma_{map|unmap} operation, which is very expensive
because cpu caches need to be invalidated.
Careful measurement of the driver rx path on armv7 reveals that
the cpu spends the majority of its time waiting for cache
invalidation.
Optimize by keeping the rx ring buffer size as close as possible
to the mtu. This limits the amount of cache that requires
invalidation.
This optimization would normally force us to re-allocate all
ring buffers when the mtu is changed - a disruptive event,
because it can only happen when the network interface is down.
Remove the need to re-allocate all ring buffers by adding support
for multi-buffer frames. Now any combination of mtu and ring
buffer size will work. When the mtu changes from mtu1 to mtu2,
consumed buffers of size mtu1 are lazily replaced by newly
allocated buffers of size mtu2.
These optimizations double the rx performance on armv7.
Third parties report 3x rx speedup on armv8.
Tested with iperf3 on a freescale imx6qp + lan7430, both sides
set to mtu 1500 bytes, measure rx performance:
Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-20.00 sec 550 MBytes 231 Mbits/sec 0
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-20.00 sec 1.33 GBytes 570 Mbits/sec 0
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier says:
====================
net: mvneta: implement basic MQPrio support
This is V2 for the MQPrio support in mvneta.
This small series adds basic support for mqprio offloading, by having
the rx queueing mirroring the TCs based on VLAN prio fields.
This was tested on Armada 3700, and proves useful to make sure
high-priority traffic has a better chance not getting dropped when
there's lots of packets incoming.
The first patch of the series deals with the per-cpu interrupts on the
armada 3700. Since they don't work, there were already some patches
applied to keep all queue mappings to CPU0, but there still were some
remaining mappings left to be dealt with.
The second patch implements the MQPrio offloading for the receive path.
Changes in V2 :
- Add a Fixes tag for the first patch
- Fix some warnings and the xmas tree in the second patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a basic MQPrio support, inserting rules in RX that translate
the TC to prio mapping into vlan prio to queues.
The TX logic stays the same as when we don't offload the qdisc.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Errata #23 "The per-CPU GbE interrupt is limited to Core
0", we can't use the per-cpu interrupt mechanism on the Armada 3700
familly.
This is correctly checked for RSS configuration, but the initial queue
mapping is still done by having the queues spread across all the CPUs in
the system, both in the init path and in the cpu_hotplug path.
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
pull-request: mlx5-next 2021-02-16
The patches in this pr are already submitted and reviewed through the
netdev and rdma mailing lists.
The series includes mlx5 HW bits and definitions for mlx5 real time clock
translation and handling in the mlx5 driver clock module to enable and
support such mode [1]
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210212223042.449816-7-saeed@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes made in eccd540 is enough for xilinx_emaclite to run
without problem on 64-bit systems. I have tested it on a Xilinx
FPGA with RV64 softcore. The architecture limitation in Kconfig
seems no longer necessary.
A small change is included to print address with %lx instead of
casting to int and print with %x.
Signed-off-by: Gary Guo <gary@garyguo.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vulturv says:
====================
bridge: mrp: Extend br_mrp_switchdev_*
This patch series extends MRP switchdev to allow the SW to have a better
understanding if the HW can implement the MRP functionality or it needs
to help the HW to run it. There are 3 cases:
- when HW can't implement at all the functionality.
- when HW can implement a part of the functionality but needs the SW
implement the rest. For example if it can't detect when it stops
receiving MRP Test frames but it can copy the MRP frames to CPU to
allow the SW to determine this. Another example is generating the MRP
Test frames. If HW can't do that then the SW is used as backup.
- when HW can implement completely the functionality.
So, initially the SW tries to offload the entire functionality in HW, if
that fails it tries offload parts of the functionality in HW and use the
SW as helper and if also this fails then MRP can't run on this HW.
Based on these new calls, implement the switchdev for Ocelot driver. This
is an example where the HW can't run completely the functionality but it
can help the SW to run it, by trapping all MRP frames to CPU.
Also this patch series adds MRP support to DSA and implements the Felix
driver which just reuse the Ocelot functions. This part was just compiled
tested because I don't have any HW on which to do the actual tests.
v4:
- remove ifdef MRP from include/net/switchdev.h
- move MRP implementation for Ocelot in a different file such that
Felix driver can use it.
- extend DSA with MRP support
- implement MRP support for Felix.
v3:
- implement the switchdev calls needed by Ocelot driver.
v2:
- fix typos in comments and in commit messages
- remove some of the comments
- move repeated code in helper function
- fix issue when deleting a node when sw_backup was true
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement functions 'port_mrp_add', 'port_mrp_del',
'port_mrp_add_ring_role' and 'port_mrp_del_ring_role' to call the mrp
functions from ocelot.
Also all MRP frames that arrive to CPU on queue number OCELOT_MRP_CPUQ
will be forward by the SW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading MRP in HW. Currently implement the switchdev
calls 'SWITCHDEV_OBJ_ID_MRP', 'SWITCHDEV_OBJ_ID_RING_ROLE_MRP',
to allow to create MRP instances and to set the role of these instances.
Add DSA_NOTIFIER_MRP_ADD/DEL and DSA_NOTIFIER_MRP_ADD/DEL_RING_ROLE
which calls to .port_mrp_add/del and .port_mrp_add/del_ring_role in the
DSA driver for the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return values of the br_mrp_switchdev function.
In case of:
- BR_MRP_NONE, return the error to userspace,
- BR_MRP_SW, continue with SW implementation,
- BR_MRP_HW, continue without SW implementation,
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the br_mrp_switchdev functions to be able to have a
better understanding what cause the issue and if the SW needs to be used
as a backup.
There are the following cases:
- when the code is compiled without CONFIG_NET_SWITCHDEV. In this case
return success so the SW can continue with the protocol. Depending
on the function, it returns 0 or BR_MRP_SW.
- when code is compiled with CONFIG_NET_SWITCHDEV and the driver doesn't
implement any MRP callbacks. In this case the HW can't run MRP so it
just returns -EOPNOTSUPP. So the SW will stop further to configure the
node.
- when code is compiled with CONFIG_NET_SWITCHDEV and the driver fully
supports any MRP functionality. In this case the SW doesn't need to do
anything. The functions will return 0 or BR_MRP_HW.
- when code is compiled with CONFIG_NET_SWITCHDEV and the HW can't run
completely the protocol but it can help the SW to run it. For
example, the HW can't support completely MRM role(can't detect when it
stops receiving MRP Test frames) but it can redirect these frames to
CPU. In this case it is possible to have a SW fallback. The SW will
try initially to call the driver with sw_backup set to false, meaning
that the HW should implement completely the role. If the driver returns
-EOPNOTSUPP, the SW will try again with sw_backup set to false,
meaning that the SW will detect when it stops receiving the frames but
it needs HW support to redirect the frames to CPU. In case the driver
returns 0 then the SW will continue to configure the node accordingly.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the enum br_mrp_hw_support that is used by the br_mrp_switchdev
functions to allow the SW to detect the cases where HW can't implement
the functionality or when SW is used as a backup.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the member sw_backup to the structures switchdev_obj_ring_role_mrp
and switchdev_obj_in_role_mrp. In this way the SW can call the driver in
2 ways, once when sw_backup is set to false, meaning that the driver
should implement this completely in HW. And if that is not supported the
SW will call again but with sw_backup set to true, meaning that the
HW should help or allow the SW to run the protocol.
For example when role is MRM, if the HW can't detect when it stops
receiving MRP Test frames but it can trap these frames to CPU, then it
needs to return -EOPNOTSUPP when sw_backup is false and return 0 when
sw_backup is true.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove #IS_ENABLED(CONFIG_BRIDGE_MRP) from switchdev.h. This will
simplify the code implements MRP callbacks and will be similar with the
vlan filtering.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 88E1111 is operating in SGMII mode, auto-negotiation should be enabled
on the SGMII side so that the link will come up properly with PCSes which
normally have auto-negotiation enabled. This is normally the case when the
PHY defaults to SGMII mode at power-up, however if we switched it from some
other mode like 1000Base-X, as may happen in some SFP module situations,
it may not be, particularly for modules which have 1000Base-X
auto-negotiation defaulting to disabled.
Call genphy_check_and_restart_aneg on the fiber page to ensure that auto-
negotiation is properly enabled on the SGMII interface.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún says:
====================-
Add 5gbase-r PHY interface mode
there is still some testing needed for Amethyst patches, so I have
split the part adding support for 5gbase-r interface mode and am sending
it alone.
The first two patches are already reviewed.
Changes since last patches (Amethyst v16):
- added phylink 5gbase-r handler
- added SFP support for 5gbase-r mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfp_parse_support() function is setting 5000baseT_Full in some cases.
Now that we have PHY_INTERFACE_MODE_5GBASER interface mode available,
change sfp_select_interface() to return PHY_INTERFACE_MODE_5GBASER if
5000baseT_Full is set in the link mode mask.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5gbase-r PHY interface mode.
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver tried to communicate towards the PHY driver whether it
wanted RGMII in-band signaling enabled or disabled however there is
nothing that looks at those flags in drivers/net/phy/broadcom.c so this
does do not anything.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjarni Jonasson says:
====================
Fixes applied to VCS8514
3 different fixes applied to VSC8514:
LCPLL reset, serdes calibration and coma mode disabled.
Especially the serdes calibration is large and is now placed
in a new file 'mscc_serdes.c' which can act as
a placeholder for future serdes configuration.
v1 -> v2:
Preserved reversed christmas tree
Removed forward definitions
Fixed build issues
Changed net to net-next
v2 -> v3:
Added cover letter.
Removed ena_clk_bypass from function call
Created mscc_serdes.c and .h for serdes configuration
Modified coma register config.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'coma mode' (configurable through sw or hw) provides an
optional feature that may be used to control when the PHYs become active.
The typical usage is to synchronize the link-up time across
all PHY instances. This patch releases coma mode if not done by hardware,
otherwise the phys will not link-up.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IB serdes calibration algorithm (performed by the onboard 8051)
has proven to be unstable for the VSC8514 QSGMII phy.
A new algorithm has been developed based on
'Frequency-offset Jittered-Injection' or 'FoJi' method which solves
all known issues. This patch disables the 8051 algorithm and
replaces it with the new FoJi algorithm.
The calibration is now performed in a new file (mscc_serdes.c),
which can act as an placeholder for future serdes configurations.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At Power-On Reset, transients may cause the LCPLL to lock onto a
clock that is momentarily unstable. This is normally seen in QSGMII
setups where the higher speed 6G SerDes is being used.
This patch adds an initial LCPLL Reset to the PHY (first instance)
to avoid this issue.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device timestamp can be in real time mode (cycles to time translation is
offloaded into the Hardware). With real time mode, HW provides timestamp
which is already translated into nanoseconds.
With this mode, driver adjusts both the HW and timecounter (to keep
clock_info_page updated) using callbacks: adjfreq, adjtime and settime.
HW clock modifications are done via MTUTC access reg commands. Driver is
allowed to modify HW real time clock only if MCAM ptpcyc2realtime_modify
capability is set.
Add MTUTC set function to be used for configuring the HW real time
clock. Modify existing code to support both internal timer (with
conversion via timecounter_cyc2time() and real time (no conversions).
Align the signatures of the helpers converting from timestamp to
nanoseconds. With that, when allocating a queue assign the corresponding
callback with respect to the capability.
Adjust 1PPS timestamp calculation flows based on the timestamp mode.
Cyc2time offload brings two major advantages:
- Improve MTAE (Max Time Absolute Error) for HW TS by up to 160 ns over a
100% loaded CPU.
- Faster data-path timestamp to nanoseconds, as translation is
lock-less and done in HW.
On real time mode, timestamp format is 32 high bits of seconds and 32
low bits of nanoseconds. On some flows, driver shall convert this format
into nanoseconds wall-clock with REAL_TIME_TO_NS macro.
HW supports a single clock, and it is shared by all functions on a
device. In case real time clock is used, it is recommended to use
a single GM to all device's functions.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Some of PPS logic (timestamp calculations) fits only internal timer
timestamp mode. Move these logics into helper functions. Later in the
patchset cyc2time HW translation mode will expose its own PPS timestamp
calculations.
With this change, main flow will only hold calling PPS logic based on run
time mode.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Internal timer mode (SW clock) requires some PTP clock related metadata
structs. Real time mode (HW clock) will not need these metadata structs.
This separation emphasize the different interfaces for HW clock and SW
clock.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Function mlx5_init_clock() is responsible for internal PTP related metadata
initializations. Break mlx5_init_clock() to sub functions, each takes care
of its own logic.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add needed structure layouts and defines for MTUTC (Management UTC)
register. MTUTC will be used for cyc2time HW translation.
In addition, add cyc2time modify capability bit and init segment HCA
real time address.
Finally, add capability bits indicating which time-stamping format is
supported per SQ and RQ. Add ts_format in the queue's context layout to
allow configuration.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Vladimir Oltean says:
====================
Fix buggy brport flags offload for SJA1105 DSA
I am resending this series because the title and the patches were mixed
up and these patches were lost. This series' cover letter was used as
the merge commit for the unrelated "Fixing build breakage after "Merge
branch 'Propagate-extack-for-switchdev-LANs-from-DSA'"" series, as can
be seen below:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=ca04422afd6998611a81d0ea1b61d5a5f4923f84
while the actual patches from the "Fix buggy brport flags offload for
SJA1105 DSA" series were marked as superseded and not applied:
https://patchwork.kernel.org/project/netdevbpf/cover/20210214155704.1784220-1-olteanv@gmail.com/
which they should have.
I know with so many bugs I introduced it's hard to keep track, I'm sorry.
Original series description:
While testing software bridging on sja1105, I discovered that I managed
to introduce two bugs in a single patch submitted recently to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite embarrasingly, I managed to fool myself into thinking that the
flooding domain of sja1105 source ports is restricted by the forwarding
domain, which it isn't. Frames which match an FDB entry are forwarded
towards that entry's DESTPORTS restricted by REACH_PORT[SRC_PORT], while
frames that don't match any FDB entry are forwarded towards
FL_DOMAIN[SRC_PORT] or BC_DOMAIN[SRC_PORT].
This means we can't get away with doing the simple thing, and we must
manage the flooding domain ourselves such that it is restricted by the
forwarding domain. This new function must be called from the
.port_bridge_join and .port_bridge_leave methods too, not just from
.port_bridge_flags as we did before.
Fixes: 4d94235495 ("net: dsa: sja1105: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a mistake, the driver always sets the address learning flag to
the previously stored value, and not to the currently configured one.
The bug is visible only in standalone ports mode, because when the port
is bridged, the issue is masked by .port_stp_state_set which overwrites
the address learning state to the proper value.
Fixes: 4d94235495 ("net: dsa: sja1105: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes references to uninitialized variables and
debugfs entry name for CN10K platform and HW_TSO flag check.
Fixes: 3ad3f8f93c ("octeontx2-af: cn10k: MAC internal loopback support").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
v1-v2
- Clear HW_TSO flag for 96xx B0 version.
This patch fixes the bug introduced by the commit
3ad3f8f93c ("octeontx2-af: cn10k: MAC internal loopback support").
These changes are not yet merged into net branch, hence submitting
to net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver fails to probe, it would be nice to not leak memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_init_port is called only if dsa_is_unused_port == false, however
ocelot_deinit_port is called unconditionally. This causes a warning in
the skb_queue_purge inside ocelot_deinit_port saying that the spin lock
protecting ocelot_port->tx_skbs was not initialized.
Fixes: e5fb512d81 ("net: mscc: ocelot: deinitialize only initialized ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the 'ionic_reset_cb' typedef as it is not used.
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-02-16
The following pull-request contains BPF updates for your *net-next* tree.
There's a small merge conflict between 7eeba1706e ("tcp: Add receive timestamp
support for receive zerocopy.") from net-next tree and 9cacf81f81 ("bpf: Remove
extra lock_sock for TCP_ZEROCOPY_RECEIVE") from bpf-next tree. Resolve as follows:
[...]
lock_sock(sk);
err = tcp_zerocopy_receive(sk, &zc, &tss);
err = BPF_CGROUP_RUN_PROG_GETSOCKOPT_KERN(sk, level, optname,
&zc, &len, err);
release_sock(sk);
[...]
We've added 116 non-merge commits during the last 27 day(s) which contain
a total of 156 files changed, 5662 insertions(+), 1489 deletions(-).
The main changes are:
1) Adds support of pointers to types with known size among global function
args to overcome the limit on max # of allowed args, from Dmitrii Banshchikov.
2) Add bpf_iter for task_vma which can be used to generate information similar
to /proc/pid/maps, from Song Liu.
3) Enable bpf_{g,s}etsockopt() from all sock_addr related program hooks. Allow
rewriting bind user ports from BPF side below the ip_unprivileged_port_start
range, both from Stanislav Fomichev.
4) Prevent recursion on fentry/fexit & sleepable programs and allow map-in-map
as well as per-cpu maps for the latter, from Alexei Starovoitov.
5) Add selftest script to run BPF CI locally. Also enable BPF ringbuffer
for sleepable programs, both from KP Singh.
6) Extend verifier to enable variable offset read/write access to the BPF
program stack, from Andrei Matei.
7) Improve tc & XDP MTU handling and add a new bpf_check_mtu() helper to
query device MTU from programs, from Jesper Dangaard Brouer.
8) Allow bpf_get_socket_cookie() helper also be called from [sleepable] BPF
tracing programs, from Florent Revest.
9) Extend x86 JIT to pad JMPs with NOPs for helping image to converge when
otherwise too many passes are required, from Gary Lin.
10) Verifier fixes on atomics with BPF_FETCH as well as function-by-function
verification both related to zero-extension handling, from Ilya Leoshkevich.
11) Better kernel build integration of resolve_btfids tool, from Jiri Olsa.
12) Batch of AF_XDP selftest cleanups and small performance improvement
for libbpf's xsk map redirect for newer kernels, from Björn Töpel.
13) Follow-up BPF doc and verifier improvements around atomics with
BPF_FETCH, from Brendan Jackman.
14) Permit zero-sized data sections e.g. if ELF .rodata section contains
read-only data from local variables, from Yonghong Song.
15) veth driver skb bulk-allocation for ndo_xdp_xmit, from Lorenzo Bianconi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields declare which timestamp mode is supported by the device
per RQ/SQ/QP.
In addition add the ts_format field to the select the mode for
RQ/SQ/QP.
Link: https://lore.kernel.org/r/20210209131107.698833-2-leon@kernel.org
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
The variable mfs_max is not initialized and is being compared to find
the maximum value. Fix this by initializing it to 0.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 90bc8e003b ("i40e: Add hardware configuration for software based DCB")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
AR8035 recently gained MDIX support. The same functions will work for
the AR8031/33 PHY. We just need to add the at803x_config_aneg()
callback.
This was tested on a Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij