On power-on LNB power supply voltage is disabled, due to that no
need to disable it during probe. Tone is supply is hard-coded as
external tone coming from the demodulator. Program both voltage
and tone on set_voltage(). Use register cache to prevent unneeded
programming.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As driver is now proper I2C client driver, we could use correct
functions for I2C I/O. Also rename state from priv to dev. Fix
logging too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove legacy media attach as all users are on I2C bindings now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though 'compatability' has a dedicated entry in the Wiktionary,
it's listed as 'Mispelling of compatibility'. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> for the atomic_helper.c
Signed-off-by: Jiri Kosina <jkosina@suse.com>
drivers/built-in.o: In function `ts2020_read_signal_strength':
ts2020.c:(.text+0x298ff94): undefined reference to `__divdi3'
ts2020.c:(.text+0x298ffd4): undefined reference to `__divdi3'
ts2020.c:(.text+0x298fffd): undefined reference to `__divdi3'
Makefile:921: recipe for target 'vmlinux' failed
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Statistics polling can not be done by lmedm04 driver's implementation of
M88RS2000/TS2020 because I2C messages stop the device's demuxer, so allow
polling for statistics to be suppressed in the ts2020 driver by setting
dont_poll in the ts2020_config struct.
Reported-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Copy the loop_through setting from the ts2020_config struct to the internal
ts2020_priv struct so that it can actually be used.
Whilst we're at it, group the bitfields together in the same order in both
structs so that the compiler has a good chance to copy them in one go.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide a DVBv5 API signal strength. This is in units of 0.001 dBm rather
than a percentage.
>From Antti Palosaari's testing with a signal generator, it appears that the
gain calculated according to Montage's specification if negated is a
reasonable representation of the signal strength of the generator.
To this end:
(1) Polled statistic gathering needed to be implemented in the TS2020 driver.
This is done in the ts2020_stat_work() function.
(2) The calculated gain is placed as the signal strength in the
dtv_property_cache associated with the front end with the scale set to
FE_SCALE_DECIBEL.
(3) The DVBv3 format signal strength then needed to be calculated from the
signal strength stored in the dtv_property_cache rather than accessing
the value when ts2020_read_signal_strength() is called.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS2020 and TS2022 tuners take an input from the demodulator indicating the
AGC setting on that component that is then used to influence the tuner's own
gain. This should be taken into account when calculating the gain and signal
strength.
Further, the existing TS2020 driver miscalculates the signal strength as the
result of its calculations can exceed the storage capacity of the 16-bit word
used to return it to userspace.
To this end:
(1) Add a callback function (->get_agc_pwm()) in the ts2020_config struct that
the tuner can call to get the AGC PWM value from the demodulator.
(2) Modify the TS2020 driver to calculate the gain according to Montage's
specification with the adjustment that we produce a negative value and
scale it to 0.001dB units (which is what the DVBv5 API will require):
(a) Callback to the demodulator to retrieve the AGC PWM value and then
turn that into Vagc for incorporation in the calculations. If the
callback is unset, assume a Vagc of 0.
(b) Calculate the tuner gain from a combination of Vagc and the tuner's RF
gain and baseband gain settings.
(3) Turn this into a percentage signal strength as per Montage's
specification for return to userspace with the DVBv3 API.
(4) Provide a function in the M88DS3103 demodulator driver that can be used to
get the AGC PWM value on behalf of the tuner.
(5) The ts2020_config.get_agc_pwm function should be set by the code that
stitches together the drivers for each card.
For the DVBSky cards that use the M88DS3103 with the TS2020 or the TS2022,
set the get_agc_pwm function to point to m88ds3103_get_agc_pwm.
I have tested this with a DVBSky S952 card which has an M88DS3103 and a TS2022.
Thanks to Montage for providing access to information about the workings of
these parts.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use regmap for I2C register access.
Remove own I2C repeated mutex as it should not be needed. I2C adapter
lock is already taken when I2C mux adapter is called, no need for
double locking.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename driver state from priv to dev.
Use I2C client for correct logging.
Use adapter and address from I2C client structure where needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ts2020_attach() allocates a variable pdata on the stack and then passes a
pointer to it to i2c_new_device() which stashes the pointer in persistent
structures.
Add a comment to the effect that this isn't actually an error because the
contents of the variable are only used in ts2020_probe() and this is only
called ts2020_attach()'s stack frame exists.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Register driver using I2C bindings internally when legacy media
attach is used. That is done by registering driver using I2C binding
from legacy attach. That way we can get valid I2C client, which is
needed for proper dev_() logging and regmap for example even legacy
binding is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* We don't need calculate channel bandwidth from symbol rate as it
is calculated by DVB core.
* Use clamp() to force upper/lower limit of filter 3dB frequency.
Upper limit should never exceeded 40MHz (80MHz BW) in any case,
though...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used frequency synthesizer is simple Integer-N PLL, with configurable
reference divider, output divider and of course N itself. Old
calculations were working fine, but not so easy to understand.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct timeval uses a 32-bit seconds representation which will
overflow in the year 2038 and beyond. This patch replaces
the usage of struct timeval with ktime_t which is a 64-bit
timestamp and is year 2038 safe.
This patch is part of a larger attempt to remove all instances
of 32-bit timekeeping variables (timeval, timespec, time_t)
which are not year 2038 safe, from the kernel.
[mchehab@osg.samsung.com: add a missing parenthesis, breaking compilation]
Suggested-by: Arnd Bergmann <arndb@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB API was originally defined using typedefs. This is against
Kernel CodingStyle, and there's no good usage here. While we can't
remove its usage on userspace, we can avoid its usage in Kernelspace.
So, let's do it.
This patch was generated by this shell script:
for j in $(grep typedef include/uapi/linux/dvb/frontend.h |cut -d' ' -f 3); do for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f); do sed "s,${j}_t,enum $j," <$i >a && mv a $i; done; done
While here, make CodingStyle fixes on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> # for drivers/media/firewire/*
We must return -ENODEV error on case probe() fails to detect chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to set some error codes here.
Fixes: f01919e8f5 ('[media] m88ds3103: add I2C client binding')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/dib0090.c:1710 dib0090_dc_offset_calibration() warn: missing break? reassigning '*tune_state'
There's no need to change tune_state there, as the fall though code
will change it again to another state. So, simplify it by
removing the dead code.
While here, fix a typo:
Sart => Start
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/drxk_hard.c:3277 dvbt_sc_command() warn: missing break? reassigning 'status'
This is basically because the error handling logic there was crappy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need own I2C locking because of tuner I2C adapter/repeater.
Firmware command is executed using I2C send + reply message. Default
I2C adapter locking protects only single I2C operation, not whole
send + reply sequence as needed. Due to that, it was possible tuner
I2C message interrupts firmware command sequence.
Reported-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement I2C client device binding.
Wrap media attach to driver I2C probe.
Add wrapper from m88ds3103_attach() to m88ds3103_probe() via driver
core in order to provide proper I2C client for legacy media attach
binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use jiffies to set timeout for DiSEqC TX ready polling. Using jiffies
is more elegant solution than looping N times with sleep.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement DVBv5 BER statistics.
Wrap legacy DVBv3 BER to DVBv5 BER.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do not return error from get_frontend() when status is queried, but
the frontend didn't lock yet. The proper behavior is to only update the
cache after having a lock.
[mchehab@osg.samsung.com: fix the patch description]
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/cx24120.c:837:6: warning: symbol 'cx24120_calculate_ber_window' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ucblocks register is probably a counter and not a rate; assume
it is so and change the calculations as required.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This code works fine but static checkers complain. The test_bit()
function takes the bit number and not a mask. Then the other issue is
that we were using USB_STATE_URB_BUF which is BIT(0) instead of URB_BUF.
Also we were open coding that instead of using the test/clear/set_bit()
functions.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These state vars are used for more than just ber calculation, also
fix typo.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
BER & UCB aren't available unless we're locked; don't update dvbv5
stats when not locked and mark these counters as unavailable.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBv3 is a legacy API. Drivers should use DVBv5, in order to support
modern applications. So, implement UCB using dvbv5.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of reading BER again for DVBv3 call, use the value from the cache.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBv3 is a legacy API. Drivers should use DVBv5, in order to support
modern applications. So, implement BER using dvbv5.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use const on the static data, as gcc may optimize better the
code. Also, would prevent that some code would override the
data there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
As reported by smatch:
drivers/media/dvb-frontends/cx24120.c: In function 'cx24120_message_send':
drivers/media/dvb-frontends/cx24120.c:368:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret, ficus;
^
The values written by cx24120 are never checked. So, remove the
check here too. That's said, the best would be to do the reverse,
but globally: to properly handle the error codes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Add in all the likely values for setting fec on tuning. Some values
yet to be tested but very likely to be correct.
In the very unlikely event that these are wrong tuning with
FEC_AUTO will still work.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove reg1 by refactoring for loops
Change ret into an int as it's only used for return values now,
and remove reset_result by using ret instead.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use reg instead of ret for all calls to readreg, remove ret_EA
as it doesn't need to be a separate var anymore.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Probably a remnant of this driver being reverse engineered,
cx24120_init assigned ret on each call to writereg - they're not
used for anything so remove them to clear up the codebase.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove __func__ from calls to dev_dbg as dynamic debug can add in
the function name anyway.
Remove debug call in dvbv3 read_signal_strength as userspace has
this value anyway.
Reword some strings to make them simpler / more obvious.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Better to report CNR via DVBv5 stats, as scale can be used.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous version of this driver had a memset before every call
to cmd. This meant the default value of cmd.arg[1] was zero unless
burst is set. Make sure it remains zero.
Also fe_sec_mini_cmd_t is an enum, so test against it.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Algorithm copied from cx24117.c - it seems to work. Showing 95% on
a signal I know to be somewhere around 74dBuV.
[mchehab@osg.samsung.net: merged two patches, to avoid breaking compilation]
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes DVBv3 signal strength to read from the cache by
moving the signal strength reading routine into get_stat, and
reducing read_signal_strength to just returning the cached value.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
get_frontend was making a call to read_status, which is being
called periodically anyway. Have read_status store fe_status in
the state struct instead and use that within get_frontend.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch added in collection, this patch enables them by
signalling they are available.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new get_stats function, called from read_status, for
collecting DVBv5 stats into the frontend cache. Only signal
strength for now, can add others later.
Not currently marked as available, future patch will enable.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change calculate_vco function to send_vco to tidy up cx24120_init
function.
xxyyzz variable is remnants of a manual div & remainder codepath
to perform a u64 rounded div; replace with kernel macro
DIV_ROUND_CLOSEST_ULL
Hex values provided to the message are mainly variables calculated
within this function, replace with these to remove hardcoding.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
msg.len has been ++'d so msg.len is one too many.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds in a missing command to cx24120_check_cmd. This part
of the old reverse engineered driver was quite hard to follow - it's
presumed the compiler did some neat optimisation that wasn't easy to
decode. This command was checked for in that version but not copied
across to the new switch statement.
For reference, old reverse engineered code:
xxzz = cmd->id - 0x11; // look for specific message id
if ( xxzz <= 0x13 ) {
msg_cmd_mask = 1 << xxzz;
//0x0F8021 // if cmd_id 17 or 22 or 33-36, 42, 47, 57-61 etc. disable mpeg output
if ( msg_cmd_mask & 0x0F8021 ) { // 000011111000000000100001b
cx24120_msg_mpeg_output_global_config(state, 0);
msleep(100);
state->dvb_s2_mode &= 0xFD; // reset mpeg out enable flag
}
}
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch removes the requirement of waiting for tune in
set_frontend by moving the clock set call into read_status
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes DVB-S/DVB-S2 to the more commonly used
DVB-S/S2 in the description for DVB_CX24120
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patches fixes all checkpatch-errors.
Even the ones created --strict.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro pointed out some coding style issues in his review.
This patch fixes them.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some i2c-hosts are quite limited regarding maximum
i2c-burst-write-sizes. This patch makes the previously
hardcoded field configurable by users of the driver.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fixes printk-related checkpatch warnings. All printks
have been converted to pr_warn or pr_info or pr_err.
Signed-off-by: Patrick.Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the Technisat Skystar S2 - this
has been tried before but the cx24120 driver was a bit out of shape
and it didn't got any further:
https://patchwork.linuxtv.org/patch/10575/
It is an old card, but currently being sold off for next to nothing,
so it's proving quite popular of late. Noticing it's quite similar
to the cx24116 and cx24117 I've rewritten the driver in a similar way.
There were a few registers and commands from those drivers
missing from this one I've tested out and found they do something so
they've been added in to speed up tuning and to make get_frontend
return something useful.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick.Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add initial support for fc2580 tuner based devices.
Tuner is controlled via V4L2 subdevice API.
Passes v4l2-compliance tests.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GoTView MasterHD 3 is a DVB-T2/C USB 2.0 tuner.
It's based on the following components:
- USB bridge: RTL2832P (contains also DVB-T demodulator)
- Demodulator: Si2168-A30
- Tuner: Si2148-A20
The demodulator and the tuner will need firmwares. The Si2148 uses Si2158
firmware. Antti has the firmwares available for download:
http://palosaari.fi/linux/v4l-dvb/firmware/
Do note that for DVB-T either of the demodulators can be used. DVB-C and
DVB-T2 are only supported by the Si2168 demodulator. The driver will
register 2 frontends for the same adapter. Frontend 0 will be the RTL2832
demodulator and frontend 1 will be the Si2168 demodulator. The same
tuner is used for both.
As a consequence of the above, it's recommended to use application that
does implement proper DVBv5 support.
For some reason, the old I2C write method sporadically fails. Thus the
need for an option to only use the new I2C write method supported by the
RTL2832.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return error from si2168_cmd_execute in case the demodulator returns an
error.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a parameter in si2168_config to support gapped clock. This might be
necessary on some devices with higher bitrates.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Bellow is yelling. Ok, sometimes the code is yells a lot, but
but this is not the case there ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix several typos inside the driver's comments.
Signed-off-by: Cheolhyun Park <pch851130@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/tda10086.c:476 tda10086_get_frontend() warn: should 'tda10086_read_byte(state, 81) << 8' be a 64 bit type?
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The indentation on this driver were deadly broken. On lots
of places, it was using 4 spaces instead of tab to indent.
On other parts, it were using tabs.
Also, on several places, it were not even being properly aligned,
as reported by smatch:
drivers/media/dvb-frontends/dib0070.c:179 dib0070_set_bandwidth() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:198 dib0070_captrim() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:246 dib0070_set_ctrl_lo5() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:260 dib0070_ctrl_agc_filter() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:494 dib0070_tune_digital() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:498 dib0070_tune_digital() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:655 dib0070_reset() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:711 dib0070_reset() warn: curly braces intended?
drivers/media/dvb-frontends/dib0070.c:713 dib0070_reset() warn: inconsistent indenting
My first idea were to leave it as-is or to just touch the above.
However, this won't be fixing anything. So, as painful as it
is, let's fix indentation globally on the driver, and then
address the inconsistencies.
Hopefully, this driver doesn't have much patches, so it likely
won't conflict to any other patch during this merge window.
Besides the big size of this patch, no functional changes
were done.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/stv0297.c:140 stv0297_get_symbolrate() warn: should 'stv0297_readreg(state, 86) << 8' be a 64 bit type?
drivers/media/dvb-frontends/stv0297.c:141 stv0297_get_symbolrate() warn: should 'stv0297_readreg(state, 87) << 16' be a 64 bit type?
drivers/media/dvb-frontends/stv0297.c:142 stv0297_get_symbolrate() warn: should 'stv0297_readreg(state, 88) << 24' be a 64 bit type?
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If userspace sends an invalid bandwidth, it should either return
EINVAL or switch to auto mode.
This driver will go past an array and program the hardware on a
wrong way if this happens.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up to 7 values:
drivers/media/dvb-frontends/s5h1420.c:193 s5h1420_send_master_cmd() error: buffer overflow 'cmd->msg' 6 <= 7
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/dib3000mc.c:134 dib3000mc_setup_pwm_state() warn: inconsistent indenting
drivers/media/dvb-frontends/dib3000mc.c:144 dib3000mc_setup_pwm_state() warn: inconsistent indenting
drivers/media/dvb-frontends/dib3000mc.c:420 dib3000mc_sleep() warn: inconsistent indenting
drivers/media/dvb-frontends/dib3000mc.c:453 dib3000mc_set_channel_cfg() warn: inconsistent indenting
The last one is actually due to a commented code. Let's rework
it, in order to remove the sparse warning without removing the
dead code, as it may be useful in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In file included from include/uapi/linux/posix_types.h:4:0,
from include/uapi/linux/types.h:13,
from include/linux/types.h:5,
from include/uapi/linux/sysinfo.h:4,
from include/uapi/linux/kernel.h:4,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/input.h:11,
from drivers/media/usb/dvb-usb/dvb-usb.h:13,
from drivers/media/usb/dvb-usb/dib0700.h:13,
from drivers/media/usb/dvb-usb/dib0700_devices.c:9:
drivers/media/dvb-frontends/dib8000.h: In function 'dib8000_attach':
include/linux/stddef.h:8:14: warning: return makes integer from pointer without a cast [-Wint-conversion]
#define NULL ((void *)0)
^
drivers/media/dvb-frontends/dib8000.h:72:9: note: in expansion of macro 'NULL'
return NULL;
^
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In file included from drivers/media/common/b2c2/flexcop-fe-tuner.c:13:0:
drivers/media/dvb-frontends/cx24123.h:54:2: warning: 'cx24123_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
cx24123_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/em28xx/em28xx-dvb.c:46:0:
drivers/media/dvb-frontends/s921.h:40:2: warning: 's921_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
s921_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/em28xx/em28xx-dvb.c:55:0:
drivers/media/dvb-frontends/mb86a20s.h:49:2: warning: 'mb86a20s_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
mb86a20s_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/mb86a20s.h:49:2: warning: 'mb86a20s_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
mb86a20s_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
* patchwork: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
Now that the kernel provides DIV_ROUND_CLOSEST_ULL(), drop the internal
implementation and use the kernel one.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Changeset 9b174527e7 added this new macro, ensuring that it
is true only if the function is actually reachable.
However, newer drivers were added since when it was written.
So, change those drivers to also use it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the media drivers, the v4l2 core knows about all submodules
and calls into them from a common function. However this cannot
work if the modules that get called are loadable and the
core is built-in. In that case we get
drivers/built-in.o: In function `set_type':
drivers/media/v4l2-core/tuner-core.c:301: undefined reference to `tea5767_attach'
drivers/media/v4l2-core/tuner-core.c:307: undefined reference to `tea5761_attach'
drivers/media/v4l2-core/tuner-core.c:349: undefined reference to `tda9887_attach'
drivers/media/v4l2-core/tuner-core.c:405: undefined reference to `xc4000_attach'
This was working previously, until the IS_ENABLED() macro was used
to replace the construct like
#if defined(CONFIG_DVB_CX24110) || (defined(CONFIG_DVB_CX24110_MODULE) && defined(MODULE))
with the difference that the new code no longer checks whether it is being
built as a loadable module itself.
To fix this, this new patch adds an 'IS_REACHABLE' macro, which evaluates
true in exactly the condition that was used previously. The downside
of this is that this trades an obvious link error for a more subtle
runtime failure, but it is clear that the change that introduced the
link error was unintentional and it seems better to revert it for
now. Also, a similar change was originally created by Trent Piepho
and then reverted by teh change to the IS_ENABLED macro.
Ideally Kconfig would be used to avoid the case of a broken dependency,
or the code restructured in a way to turn around the dependency, but either
way would require much larger changes here.
Fixes: 7b34be71db ("[media] use IS_ENABLED() macro")
See-also: c5dec9fb24 ("V4L/DVB (4751): Fix DBV_FE_CUSTOMISE for card drivers compiled into kernel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cleaning up the following compiler warning:
rtl2832.c:703:12: warning: 'tmp' may be used uninitialized in this function
Even though it could never happen since if rtl2832_rd_demod_reg () doesn't set
tmp, this line would never run because we go to err. It is still nice to avoid
compiler warnings.
[mchehab@osg.samsung.com: fix a merge conflict with another patch meant
to fix the same bug, but doing it at the wrong way]
Signed-off-by: Luis de Bethencourt <luis.bg@samsung.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case of an error function si2165_upload_firmware() releases the already
requested firmware in the exit path. However, there is one deviation where
the function directly returns. Use the correct cleanup so that the firmware
memory gets freed correctly. Detected by Coverity CID 1269120.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Luis de Bethencourt <luis.bg@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to use bulk i2c_transfer() to write single register.
Use write register function instead.
Tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TS2022 is slightly newer and different version of same tuner, which
could be supported with rather small changes. Tuner type is
auto-detected.
Tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Caching register reads causes some random I/O errors on channel
change. Disable caching now in order to avoid those errors.
Reverts partly commit dcadb82
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
>From the daily build:
rtl2832.c: In function 'rtl2832_read_status':
rtl2832.c:703:12: warning: 'tmp' may be used uninitialized in this function [-Wmaybe-uninitialized]
} else if (tmp == 10) {
^
The code is OK, it's just the compiler that cannot figure out what's
going on. So just init 'tmp' to 0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add xtal as a configuration parameter so it can be used
in the IF register value calculation. If not set in the
configuration then use a default value.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix a few minor CodingStyle issues at the source code:
- Use proper multi-line comments;
- Align the log tables;
- Remove the .type from dvb_frontend_ops, since this is not
needed anymore (since the drivers conversion to DVBv5);
- Remove emacs format macro.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ideally, we should be replacing this function by intlog10().
While we don't do that, let's at least constify the tables,
in order to remove its code footfrint, and get rid of nelems.
This also fixes a few 80-cols CodingStyle warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
WARNING: braces {} are not necessary for any arm of this statement
+ if (ret == 0) {
[...]
+ } else {
[...]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Get rid of the remaining checkpatch.pl warnings:
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logic there is too complex and it looks like an inifite
loop.
So, simplify the logic and implement it as a for loop.
This gets rid of the following checkpatch.pl warnings:
WARNING: else is not generally useful after a break or return
+ return LG3306_UNLOCK;
+ } else {
WARNING: else is not generally useful after a break or return
+ return LG3306_UNLOCK;
+ } else {
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use pr_foo() where there's a direct replacement. For debug, use
custom-made macros, for now, as there are 3 different debug levels.
We should get rid of those some day, specially since several such
macros can be just removed, as Kernel trace would provide about
the same output.
This gets rid of some checkpatch errors:
WARNING: Prefer [subsystem eg: netdev]_info([subsystem]dev, ... then dev_info(dev, ... then pr_info(... to printk(KERN_INFO ...
+#define lg_info(fmt, arg...) printk(KERN_INFO "lgdt3306a: " fmt, ##arg)
ERROR: Macros with complex values should be enclosed in parentheses
+#define lg_dbg(fmt, arg...) if (debug & DBG_INFO) \
+ lg_printk(KERN_DEBUG, fmt, ##arg)
ERROR: Macros with complex values should be enclosed in parentheses
+#define lg_reg(fmt, arg...) if (debug & DBG_REG) \
+ lg_printk(KERN_DEBUG, fmt, ##arg)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this CodingStyle error:
ERROR: Do not include the paragraph about writing to the Free Software Foundation's mailing address from the sample GPL notice. The FSF has changed addresses in the past, and may do so ag$
#56: FILE: drivers/media/dvb-frontends/lgdt3306a.c:19:
+ * along with this program; if not, write to the Free Software$
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes the following smatch errors:
drivers/media/dvb-frontends/lgdt3306a.c: In function 'lgdt3306a_set_if':
drivers/media/dvb-frontends/lgdt3306a.c:695:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
drivers/media/dvb-frontends/lgdt3306a.c: In function 'lgdt3306a_monitor_vsb':
drivers/media/dvb-frontends/lgdt3306a.c:1033:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
drivers/media/dvb-frontends/lgdt3306a.c: In function 'lgdt3306a_check_oper_mode':
drivers/media/dvb-frontends/lgdt3306a.c:1082:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
drivers/media/dvb-frontends/lgdt3306a.c: In function 'lgdt3306a_check_lock_status':
drivers/media/dvb-frontends/lgdt3306a.c:1109:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
drivers/media/dvb-frontends/lgdt3306a.c: In function 'lgdt3306a_check_neverlock_status':
drivers/media/dvb-frontends/lgdt3306a.c:1185:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
drivers/media/dvb-frontends/lgdt3306a.c: In function 'lgdt3306a_pre_monitoring':
drivers/media/dvb-frontends/lgdt3306a.c:1199:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
drivers/media/dvb-frontends/lgdt3306a.c: In function 'lgdt3306a_get_packet_error':
drivers/media/dvb-frontends/lgdt3306a.c:1310:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As warned by smatch:
drivers/media/dvb-frontends/lgdt3306a.c:1354 log10_x1000() error: buffer overflow 'valx_x10' 14 <= 14
drivers/media/dvb-frontends/lgdt3306a.c:1355 log10_x1000() error: buffer overflow 'log10x_x1000' 14 <= 14
There's a potential of returning a value out of the buffer. Fix it.
While here, remove the ugly braced block.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify the check if CONFIG_DVB_LGDT3306A is enabled, use the
IS_ENABLED() macro, just like the other frontend modules.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While this is not a mandatory rule at the CodingStyle, we prefer
hexadecimal values in lowercase. Currently, there's a mix of lowercase
and uppercase ons at lgdt3306a. So, convert all to lowercase with this
small script:
perl -ne 'if (m,0x([\dA-F]+),) { $o=$1; $n=lc $1; s,0x($o),0x$n, } print $_'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just CodingStyle. No functional changes.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
fix WARNING: 'supress' may be misspelled - perhaps 'suppress'?
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not be using typedefs at the Kernel, as this makes harder
for reviewers to understand the code.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes CodingStyle error:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need for an else, as the previous if will return.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ATSC/QAM-B demodulator is used by several new devices.
Add support for it. Other patches will fix CodingStyle issues.
Signed-off-by: Fred Richter <frichter@hauppauge.com>
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of implement its own logic, use the already-defined one.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch is based on Antti's silabs branch.
Add support for 1.7 MHz bandwidth. Supported in all versions of Si2168 according to short data sheets.
[mchehab@osg.samsung.com: Fix CodingStyle]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch should is based on Antti's silabs branch.
According to dvb-frontend.h set_frontend may be called with bandwidth_hz set to 0 if automatic bandwidth is required. Si2168 does not support automatic bandwidth and does not declare FE_CAN_BANDWIDTH_AUTO in caps.
This patch will change the behaviour in a way that EINVAL is returned if bandwidth_hz is 0.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
symbol-rate report was wrongly removed off by the commit:906aaf5a .
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/rtl2832.c:157:5: warning: no previous prototype for ‘rtl2832_bulk_write’ [-Wmissing-prototypes]
int rtl2832_bulk_write(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2832.c:169:5: warning: no previous prototype for ‘rtl2832_update_bits’ [-Wmissing-prototypes]
int rtl2832_update_bits(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2832.c:181:5: warning: no previous prototype for ‘rtl2832_bulk_read’ [-Wmissing-prototypes]
int rtl2832_bulk_read(struct i2c_client *client, unsigned int reg, void *val,
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/rtl2830.c:21:5: warning: no previous prototype for ‘rtl2830_bulk_write’ [-Wmissing-prototypes]
int rtl2830_bulk_write(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2830.c:33:5: warning: no previous prototype for ‘rtl2830_update_bits’ [-Wmissing-prototypes]
int rtl2830_update_bits(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2830.c:45:5: warning: no previous prototype for ‘rtl2830_bulk_read’ [-Wmissing-prototypes]
int rtl2830_bulk_read(struct i2c_client *client, unsigned int reg, void *val,
^
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There was 2 muxed I2C adapters, one for demod tuner bus and one for
internal use. Idea of internal I2C adapter was to force I2C repeater
close when demod access its registers. Driver has also delayed work
queue based method to close I2C repeater.
After regmap conversion internal I2C adapter based repeater close
left unused - only work queue method was in use. We could not use
internal mux adapter method with regmap as it makes recursive regmap
call, which causes deadlock as regmap has own locking. Due to that
remove whole method totally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We are consumer of DVB frontend provided by rtl28xxu module. Due to
that we must use refcount to ensure none could remove rtl28xxu when
we are alive (or when we are streaming, if more fine-grained
refcounting is wanted).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Put demod to soft reset in order to save power when sleep. That drops
power usage ~30mA @5V on USB dongle I tested. In real life it does
not matter much as USB IF powers off demod too, but now it is done
twice - demod and USB IF.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I have implemented tons of things for that driver, more than anyone
else, so lets claim copyright and module authorship.
Cc: Thomas Mair <thomas.mair86@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove all the stuff that is not needed anymore. Rename variable.
Remove extra new lines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device, platform device, for logging system in order
to format printouts correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That SDR driver module was abusing DVB frontend SEC (satellite
equipment controller) device and due to that it was also using
legacy DVB binding. Platform bus is pseudo-bus provided by kernel
driver model and it fits cases like that, where any other busses
are not suitable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' sounds better than 's' for such variable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide register read and write callbacks for SDR module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Chips uses 8-bit register addresses with 5 pages. Extend register
address by using register page as a first byte of address, defining
virtual register addresses. That is common method of handling
register pages and regmap also uses it. Remove page + address
conversion glue which was there for regmap.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to do software reset on init() as it is done a bit
later on end of set_frontend(). Software reset usually means
restarting (resetting to starting point) chip internal state machine
(FSM). Naturally it is done after all parameters are programmed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enable regmap register cache in order to reduce IO.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Demod lock flags are derived from demod state machine states. States
are running from 1 to 11, where highest state 11 means demod is
fully locked and streaming. Naturally smaller state numbers means
there is some partial locks.
Define now state 10 as missing synch and lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We don't need it anymore as all users are using muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Estimate signal strength from IF digital AGC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move all needed configuration values to platform data structure
and remove old configuration code where possible.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename it device state variable to dev. Both priv and dev are very
common terms for such variable in kernel, but I like use dev in
order to keep drivers consistent.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exported resources are not needed anymore as all users are using
callbacks carried via platform data. Due to that we will remove
those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add callback for all of those functions which are currently
exported using EXPORT_SYMBOL. That allows us convert every user to
callbacks and eventually all exported symbols could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Own I2C locking is needed due to two special reasons:
1) Chips uses multiple register pages/banks on single I2C slave.
Page is changed via I2C register access.
2) Chip offers muxed/gated I2C adapter for tuner. Gate/mux is
controlled by I2C register access.
Due to these reasons, I2C locking did not fit very well.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Trivial changes proposed by checkpatch.pl and some more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove internal config and use configuration values directly from
the platform data.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device for dev_foo() logging in order to print logs
correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As a I2C driver struct i2c_client is top level structure representing
the driver. Use it as parameter to carry all needed information for
each function in order to simplify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use name 'dev' for device state instance as it is more common and
also one letter shorter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove legacy DVB binding as all users are using I2C binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert driver to kernel I2C model. Old DVB proprietary model is
still left there also.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
X-Patchwork-Delegate: m.chehab@samsung.com
As shown at the code, upd_demod_gain_period is used to write
to two 16-bit registers:
dib8000_write_word(state, 1946, upd_demod_gain_period & 0xFFFF);
dib8000_write_word(state, 1947, reg | (1<<14) | ((upd_demod_gain_period >> 16) & 0xFF));
So, it should be declared as u32.
This fixes the following smatch warning:
drivers/media/dvb-frontends/dib8000.c:1282 dib8000_agc_startup() warn: right shifting more than type allows
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename firmware variable from fw_file to fw_name and change its type
from u8 to const char as request_firmware() input defines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Print chip version once using log level into when init() is called.
Remove cold/warm state printing as those are not very useful.
old printing:
si2168 6-0064: found a 'Silicon Labs Si2168' in cold state
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
si2168 6-0064: found a 'Silicon Labs Si2168' in warm state
new printing:
si2168 6-0064: found a 'Silicon Labs Si2168-B40'
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit 034e1ec0ce
si2168: One function call less in si2168_init() after error detection
That commit added goto label for error path to release firmware,
but forgets to remove variable NULL set. Remove those now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All known old firmware firmware formats are downloaded using 8 byte
chunks. Reject firmware if it could not be divided to 8 byte chunks
and because of that we could simplify some calculations. Now both
supported firmware download routines are rather similar.
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use own label for kzalloc failure in which does not call kfree().
kfree() could be called with NULL, but it is still better to have
own label which skips unnecessary kfree().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change formatter from signed to unsigned as stream_id is 32bit
unsigned variable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even firmware version is not needed to know, it is still interesting
and useful to know some cases. Due to that increase its printing to
info log level.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename some goto labels and more. No functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove if () from firmware command error path as there should not be
any error prone conditional logic there. Use goto labels instead.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We don't need that anymore as same pointer is passed to each
routine via struct dvb_frontend private field.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Carry struct i2c_client pointer inside struct dvb_frontend private
pointer. This driver is I2C driver, which is represented as a
struct i2c_client, so better to carry this top level structure for
each routine in order to unify things. This allows further
simplification.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' is most common name in kernel for structure containing device
state instance, so rename it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
w_scan complains about missing symbol rate limits:
This dvb driver is *buggy*: the symbol rate limits are undefined - please report to linuxtv.org
Chip supports 1 to 7.2 MSymbol/s on DVB-C.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for controlling TP clock mode for VSB and QAM annex-B/C mode.
Gated clock mode is the default value, and does not support QAM annex-C.
The patch enables setting this control to fixed clock mode.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari