- Enable dm9000 as built-in for NFSroot
- Enable dm816x USB phy as a loadable module
- Enable Pixcir touch screen as a loadable module
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QPe9
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/o2_dc' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Few omap2plus_defconfig changes for v4.2 merge window:
- Enable dm9000 as built-in for NFSroot
- Enable dm816x USB phy as a loadable module
- Enable Pixcir touch screen as a loadable module
* tag 'omap-for-v4.2/o2_dc' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_PIXCIR
ARM: omap2plus_defconfig: Add dm816x USB PHY as a loadable module
ARM: omap2plus_defconifg: Enable DM9000 in omap2plus_defconfig
* zte/soc:
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
Add basic defconfig support to zx SOC, including uart, mmc
and other common config
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add initial dts file and document for ZX296702 and board ZX296702-AD1.
More peripherals will be added later.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
After commit 02b4e2756e (ARM: v7 setup function should invalidate L1
cache) the soc specific secondary_startup is removed, causing build
failures:
../arch/arm/mach-socfpga/platsmp.c: In function 'socfpga_a10_boot_secondary':
../arch/arm/mach-socfpga/platsmp.c:66:140: error: 'socfpga_secondary_startup' undeclared (first use in this function)
../arch/arm/mach-socfpga/platsmp.c:66:140: note: each undeclared identifier is reported only once for each function it appears in
To fix, use the generic secondary_startup.
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LybA
-----END PGP SIGNATURE-----
Merge tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Samsung updates for v4.2
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
* tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (301 commits)
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
ARM: EXYNOS: Get current parent clock for power domain on/off
ARM: SAMSUNG: fix clk_enable() WARNing in S3C24XX ADC
ARM: EXYNOS: Add missing of_node_put() when parsing power domains
ARM: EXYNOS: Handle of_find_device_by_node() and kstrdup() failures
ARM: EXYNOS: Handle of of_iomap() failure
Linux 4.1-rc4
....
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJVcd58AAoJEA0Cl+kVi2xqe8AP/0aSuUJZLX1Z7LJE8a2JNjZR
hE31rnsxb/LBjRi651yDRLTJ23Jfyj42JHHRO2Xck5HsDeTwjccXks1tyEZLkfXE
c5fC8metrwttIHpB+vyc0KtR7+HG1Seko90bZPftHWAxOsk2yJi5l0H7IatdYpw5
1sF3BfwGrA2qsqoB9R9JOt+Pgqquwi6taA4rFx/f2QnAxP5ijBywDTAwmUxWHkrG
SrgBKVrmQiQyTJaxuceEojg2OJj9RQxiwCMIA5Qx9cH5pf6JvysNMYxeeIA6xaDn
dml20iOgv3f1aIivsAi2HSu73hycuYv2fZ5rGpii+s0wV5VLALGD3A6QZHVeGk28
XZ7LLJV68Y47SKNAZqiokiMO68J2exYi+5SEcqfW7XDV+ODS2XPzaW5cV62AcLKx
fv7Mx791Rgch8WsfEuYDdt5Ay1Y4UgjNgcTRjEiaE/IEjLV6i8Y2xWNHqRcv8vrR
lZ1CoGKWFMouYQ0dce9WOGiXXCWCjiFerQoM7yvljFvLt/bzrVEIbV689w7tdw8j
e26/VBX2/ZQUrwh4WbUmSb69qV7vQFdVEvyb69GGIVJFge6OIAFJ3drxCYS/ikpj
dWFg9SIthsky++4zpIiMU37K7NDDu3J0Hnm1RByDaHckmIZBXO8TywzwxDlr9F+8
gCs9NdSKISXyRNIptIE1
=ZQaR
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung another DT udpates for v4.2
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
* tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (33 commits)
ARM: dts: add sysmmu nodes for exynos5420
ARM: dts: add sysmmu nodes for exynos5250
ARM: dts: add sysmmu nodes for exynos4415
ARM: dts: add sysmmu nodes for exynos3250
ARM: dts: add sysmmu nodes for exynos4
ARM: dts: Add Odroid XU3 Lite support
of: Add vendor prefix for Hardkernel
ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC
ARM: dts: exynos5420: add nodes for jpeg codec
ARM: dts: s3c2416: Use labels for overriding nodes in SMDK2416
ARM: dts: s3c2416: Add labels to S3C2416 nodes
ARM: dts: Use labels for overriding nodes in exynos5422-odroidxu3
ARM: dts: Use labels for overriding nodes in exynos5440 boards
ARM: dts: Use labels for overriding nodes in exynos5420-smdk5420
ARM: dts: Use labels for overriding nodes in exynos542x
ARM: dts: Use labels for overriding nodes in exynos5420-arndale-octa
ARM: dts: Remove duplicated I2C7 nodes in exynos5250-snow
ARM: dts: Use labels for overriding nodes in exynos5250
ARM: dts: Add labels to exynos5 nodes
ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into next/dt
Linux 4.1-rc6
Conflicts:
arch/arm/boot/dts/zynq-7000.dtsi
Resolution summary:
Mainline had an earlier version of the commit, resolve in favor of the
newer patch in next/dt branch.
- for exyos3250
: use s3c6410-rtc instead of exynos3250-rtc
: add JPEG codec node and support it on exynos3250-rinato
: use s3c-rtc clock id for exynos3250-rinato and monk boards
- for exynos4
: add JPEG codec node and syscon property to MIPI DPHY
: remove obsolete MIPI DPHY reg property
: enable s3c-rtc on exynos4412-trats2
- for exynos5
: add syscon property to MIPI DPHY for exynos5420
: enable s3c-rtc on exynos5420-arndale-octa
: add missing irq pinctrl for max77686 on exynos5250-smdk5250
: clk: add bindings for 32kHz clocks from s2mps11
: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
- for exynos5422-odroidxu3
: add mmc detect gpio and LEDs
: add HS400 support, simple-audio-card and rtc_src clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bWPy
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung DT updates for v4.2
- for exyos3250
: use s3c6410-rtc instead of exynos3250-rtc
: add JPEG codec node and support it on exynos3250-rinato
: use s3c-rtc clock id for exynos3250-rinato and monk boards
- for exynos4
: add JPEG codec node and syscon property to MIPI DPHY
: remove obsolete MIPI DPHY reg property
: enable s3c-rtc on exynos4412-trats2
- for exynos5
: add syscon property to MIPI DPHY for exynos5420
: enable s3c-rtc on exynos5420-arndale-octa
: add missing irq pinctrl for max77686 on exynos5250-smdk5250
: clk: add bindings for 32kHz clocks from s2mps11
: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
- for exynos5422-odroidxu3
: add mmc detect gpio and LEDs
: add HS400 support, simple-audio-card and rtc_src clock
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add syscon property to the MIPI DPHY for exynos4415
ARM: dts: Remove obsolete MIPI DPHY 'reg' property for exynos4
ARM: dts: Use last parent for clocks during power domain on/off
ARM: dts: add support JPEG codec for exynos3250-rinato
ARM: dts: support simple-audio-card for exynos5420 and exynos5422-odroidxu3
ARM: dts: add jpeg-codec node for exynos4 and exynos4x12
ARM: dts: Enable S3C RTC on exynos4412-trats2 and exynos5420-arndale-octa
ARM: dts: Use define for s3c-rtc clock id for exynos3250-monk
ARM: dts: Use define for s3c-rtc clock id for exynos3250-rinato
ARM: dts: Use s3c6410-rtc instead of exynos3250-rtc for exynos3250/4415
ARM: dts: add 'rtc_src' clock to rtc node for exynos5422-odroidxu3
clk: samsung: Add bindings for 32kHz clocks from s2mps11
ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
ARM: dts: Add syscon property to the MIPI phy in exynos5420
ARM: dts: Add HS400 support for exynos5422-odroidxu3
ARM: dts: Add LEDs for exynos5422-odroidxu3
ARM: dts: add mmc detect gpio for exynos5422-odroidxu3
ARM: dts: add JPEG codec device node for exynos3250
ARM: dts: Add missing irq pinctrl for max77686 on smdk5250
Enable the Exynos DSI and S6E8AA0 panel for full X11 display on Trats2.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- enable DRM_EXYNOS_DSI and DRM_PANEL_S6E8AA0
for full X11 display on Trats2 board
- enable SENSORS_PWM_FAN
to control fan power on Odroid-XU3 board
- enable SENSORS_INA2XX
for power monitor sensor on Odriod-XU3 board
- do savedefconfig
to remove useless configs and check its dependencies
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uILc
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/defconfig
exynos_defconfig updates for v4.2
- enable DRM_EXYNOS_DSI and DRM_PANEL_S6E8AA0
for full X11 display on Trats2 board
- enable SENSORS_PWM_FAN
to control fan power on Odroid-XU3 board
- enable SENSORS_INA2XX
for power monitor sensor on Odriod-XU3 board
- do savedefconfig
to remove useless configs and check its dependencies
* tag 'samsung-defconfig-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable CONFIG_SENSORS_INA2XX for Odroid-XU3
ARM: exynos_defconfig: Enable CONFIG_SENSORS_PWM_FAN for Odroid-XU3
ARM: exynos_defconfig: savedefconfig
ARM: exynos_defconfig: Enable display on Trats2 board
This includes setting up EGPIOs 0 and 9 for card detection and
chip select respectively. This patch is needed to mount a root
filesystem on the SPI-based MMC card reader found on the Sim.One.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Adjust device tree entry to the proper registered compatible
string for LIS3LV02DL.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The xdmac channel configuration is done in one cell not two. This error
prevents from probing devices correctly.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 83906783b7 ("ARM: at91/dt: sama5d4: add aes, sha and tdes nodes")
Cc: stable@vger.kernel.org # 4.1
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- rtc node for at91sam9rl/at91sam9rlek
- move to stdout-path for console on kizbox and all Atmel's boards
- Addition of the Acme Systems' Arietta G25
- two little fixes for Kizbox and sama5d4ek
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVcZyfAAoJEAf03oE53VmQv+sH+wbJx4PN0KdgGQXhOzj/UBRp
6LU4LZGGmCTxM0+FRDH9Bepjwwr8iiHTfaNPnM3bgDrEj3Ik43ekMLqgtIwrkIn2
YRfZY0t4oPZIte+weBAqDl7qHVKaVlttbZABEAVI2rQgui+LAj6T4u3rmUsvoPHU
j8NP6Ng7mWD6nb31ulrPezo33cz8jutoPerWIzclWa+sJhB4bHZHb7N4z7SvouDG
SXlvq5HkK2Az3DwT+RgHyqzSAVa/zl+rOce5LhOgD1I0p3OCPJ+aO0oxQJOaS48F
JmLsEY6xO3wavMFm5z/AHOD+sJej+iGpmHf6EwF93OVtiu83wfxIWml+xQdcjNg=
=FN7g
-----END PGP SIGNATURE-----
Merge tag 'at91-dt4' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Fourth batch of DT changes for 4.2:
- rtc node for at91sam9rl/at91sam9rlek
- move to stdout-path for console on kizbox and all Atmel's boards
- Addition of the Acme Systems' Arietta G25
- two little fixes for Kizbox and sama5d4ek
* tag 'at91-dt4' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
ARM: at91/dt: Add Acme Arietta G25
ARM: at91/dt: sama5d4 xplained: use stdout-path
ARM: at91/dt: sama5d4ek: use stdout-path
ARM: at91/dt: sama5d3 xplained: use stdout-path
ARM: at91/dt: sama5d3xek: use stdout-path
ARM: at91/dt: at91sam9x5ek: use stdout-path
ARM: at91/dt: at91sam9rlek: use stdout-path
ARM: at91/dt: at91sam9n12ek: use stdout-path
ARM: at91/dt: at91sam9m10g45ek use stdout-path
ARM: at91/dt: at91sam9g20ek: use stdout-path
ARM: at91/dt: at91sam9263ek: use stdout-path
ARM: at91/dt: at91sam9261ek: use stdout-path
ARM: at91/dt: at91rm9200ek: use stdout-path
ARM: at91/dt: kizbox: use stdout-path
ARM: at91/dt: at91sam9rlek: add RTC
ARM: at91/dt: at91sam9rl: fix rtc node
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVb7iWAAoJEFBXWFqHsHzOIGEIAJjoZ+80PKH6+obh7gCuEkIx
MkZobKxYyRRh+wD+7NZEqSPMYxBW6eUCYGCCy+f/4xjmlIfHkp/DaaCeIU0EZItl
GU1ZE7qg6kWGbamun7zXcrg1cZ+bFOpQ926isETurL8LC2+PLm6OSg1pl6hwjqpA
rGzY2aEH5Lke6wDN0cMus0ApMlIQ8HpOLABtqosuzUWclyZBmoxBQshbW8ztzS3Y
pjpRfAHS91+0vZpoqmULTc/ENbTToNYk5NxJgMMDigkz1Gqp0Ni+rxmDmRPayo09
/Nq4VHDT+wx3CSf6nC9YIrabxrBMpvTky2jWOAJ4OxMFjT0xle3XISGRoa1ifqo=
=PbGi
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.2:
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
* tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
ARM: dts: imx6dl: add imx6dl gpt specific compatible string
ARM: dts: imx6: add DT for aristainetos2 board
ARM: dts: cubox-i/hummingboard: Fix the license text
ARM: dts: sabrelite: use simple-panel instead of display-timings for LVDS0
ARM: dts: nitrogen6x: use simple-panel instead of display-timings for LVDS0
ARM: dts: add imx7d-sdb support
ARM: dts: add imx7d soc dtsi file
ARM: dts: Armadeus Systems APF6 family support (i.MX6)
ARM: dts: vf610: Nomenclature fixup for PTC12 pin used in RMII mode.
ARM: dts: cubox-i: add support for Broadcom Wifi/Bluetooth devices
Document: dt: binding: imx: update document for imx7d support
ARM: dts: imx6qdl: Add power-domain phandle to CODA device node
ARM: dts: Gateworks GW5510 support (i.MX6)
ARM: dts: imx6sl-warp: Fix OTG roles
ARM: dts: imx6sl-warp: Remove USB regulators
ARM: dts: imx6sl-warp: Remove unused regulator
ARM: dts: add pinfunc include file to support imx7d
ARM: mxs: fix in tree users of ssd1306
ARM: dts: imx6qdl-hummingboard: Add PCIe support
ARM: dts: imx23-olinuxino: Add i2c support
...
- Add new SoC i.MX7D support, which integrates two Cortex-A7 and one
Cortex-M4 cores.
- Support suspend from IRAM on i.MX53, so that DDR pins can be set to
high impedance for more power saving during suspend.
- Move i.MX clock drivers from arch/arm/mach-imx to drivers/clk/imx.
- Move i.MX GPT timer driver from arch/arm/mach-imx into
drivers/clocksource.
- A couple of clock driver update for VF610 and i.MX6Q.
- A few random code correction and improvement.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVb7grAAoJEFBXWFqHsHzOWS0H/RXV1UjvsJTfK8+KR2SGY5QO
3hU4YQYpnkukG2OtxAaWKXzIh+xeINqJ02cws/zyEfVZFsZp/i5Z7EM5811qQeNC
f9uCtFCNynTnWjUP9YXELgAX3/DPHMr+Em5QGOWwh+311YypJyP7CttsJvmjJIUN
qGYXdpy2xhqKgSGrnI+dhpxTdhtm/jmsggoM8qqi2aYB3c3rnWCc6QSBMR8oxFKB
Tmxd/cc/6Pvbp7W+AztTb/z8UD21UJkn96FhUb9563HKjf7kvbP4ydJTwhBxfyQu
YxE4kkejrnVNaUl1Tkqmf7rTgLKaU92nrLCuBDI/91OET+GQtq2R5fE8iMPs29k=
=c254
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC updates for 4.2:
- Add new SoC i.MX7D support, which integrates two Cortex-A7 and one
Cortex-M4 cores.
- Support suspend from IRAM on i.MX53, so that DDR pins can be set to
high impedance for more power saving during suspend.
- Move i.MX clock drivers from arch/arm/mach-imx to drivers/clk/imx.
- Move i.MX GPT timer driver from arch/arm/mach-imx into
drivers/clocksource.
- A couple of clock driver update for VF610 and i.MX6Q.
- A few random code correction and improvement.
* tag 'imx-soc-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (44 commits)
ARM: imx: imx7d requires anatop
clocksource: timer-imx-gpt: remove include of <asm/mach/time.h>
ARM: imx: move timer driver into drivers/clocksource
ARM: imx: remove platform headers from timer driver
ARM: imx: provide gpt device specific irq functions
ARM: imx: get rid of variable timer_base
ARM: imx: define gpt register offset per device type
ARM: imx: move clock event variables into imx_timer
ARM: imx: set up .set_next_event hook via imx_gpt_data
ARM: imx: setup tctl register in device specific function
ARM: imx: initialize gpt device type for DT boot
ARM: imx: define an enum for gpt timer device type
ARM: imx: move timer resources into a structure
ARM: imx: use relaxed IO accessor in timer driver
ARM: imx: make imx51/3 suspend optional
ARM: clk-imx6q: refine sata's parent
ARM: imx: clk-v610: Add clock for I2C2 and I2C3
ARM: mach-imx: iomux-imx31: Use DECLARE_BITMAP
ARM: imx: add imx7d clk tree support
ARM: clk: imx: update pllv3 to support imx7
...
Conflicts:
arch/arm/mach-imx/Kconfig
This pull request contains Broadcom BCM5301x related changes:
- Hauke adds the interrupt mapping for the BCM5301x PCIe controller
- Haule adds support for NAND flash using the standard Broadcom NAND controller
iProc specific binding on BCM4708/5301x
- Rafal adds support for the Asus RT-AC87U router
* tag 'arm-soc/for-4.2/dts-part3' of https://github.com/Broadcom/stblinux:
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
* socfpga/soc:
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
Add code that requests that the sdr controller go into
self-refresh mode. This code is run from ocram.
Suspend-to-RAM and EDAC support are mutually exclusive on
SOCFPGA. If the EDAC is enabled, it will prevent the
platform from going into suspend.
Example of how to request to suspend to ram:
$ echo enabled > \
/sys/devices/soc/ffc02000.serial0/tty/ttyS0/power/wakeup
$ echo -n mem > /sys/power/state
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
These options make it possible to overwrites the data and instruction
prefetching behavior of the arm pl310 cache controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit cb1293e2f5 ("ARM: 8375/1: disable some options on ARMv7-M")
causes the build to on ARMv7-M machines:
CC arch/arm/kernel/asm-offsets.s
In file included from include/linux/sem.h:5:0,
from include/linux/sched.h:35,
from arch/arm/kernel/asm-offsets.c:14:
include/linux/rcupdate.h: In function 'rcu_read_lock_sched_held':
include/linux/rcupdate.h:539:2: error: implicit declaration of function
'arch_irqs_disabled' [-Werror=implicit-function-declaration]
return preempt_count() != 0 || irqs_disabled();
asm-generic/irqflags.h provides an implementation of arch_irqs_disabled().
Lets grab an implementation from there!
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The STMicrolectornics's STM32F429 MCU has the following main features:
- Cortex-M4 core running up to @180MHz
- 2MB internal flash, 256KBytes internal RAM
- FMC controller to connect SDRAM, NOR and NAND memories
- SD/MMC/SDIO support
- Ethernet controller
- USB OTFG FS & HS controllers
- I2C, SPI, CAN busses support
- Several 16 & 32 bits general purpose timers
- Serial Audio interface
- LCD controller
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
A bunch of new DT changes for the 4.2 merge window, among which:
- Enable the SRAM controller on the A10/A10s/A13/A20
- A33 support
- New boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHR7
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.2, take 2
A bunch of new DT changes for the 4.2 merge window, among which:
- Enable the SRAM controller on the A10/A10s/A13/A20
- A33 support
- New boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
* tag 'sunxi-dt-for-4.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun6i: Add a dts file for the Mele A1000G quad top set box
ARM: dts: sun8i: Add dts file for the GA10H-A33 tablet
ARM: dts: sun8i-a33: Add dts for Sinlinx SinA33 development board.
ARM: dts: sun8i-a33: Add pinmux setting for uart0 on PB pins
ARM: dts: sun8i: Add pinmux setting for 8bit mmc2
ARM: dts: sun8i: Add usb_clk node for a23/a33
ARM: dts: sun8i: Add ET-Q8 A33 support
ARM: dts: sun8i: Add sun8i-a33 dtsi
ARM: dts: sun8i: Add sun8i-a23-a33 dtsi
ARM: dts: sun7i: Add A20 SRAM and SRAM controller
ARM: dts: sun5i: Add A10s and A13 SRAM and SRAM controller
ARM: dts: sun4i: Add A10 SRAM and SRAM controller
ARM: dts: sunxi: Revert SRAM controller drivers patches
ARM: dts: sun9i: Add device node for watchdog
ARM: dts: sun7i: Add uart4 support for BananaPro, disable uart2
ARM: dts: sun7i: Add uart4_pins_b definition
ARM: sun8i: Introduce A23 Evaluation Board Support
Update the arria10 gmac nodes with all the necessary properties for ethernet
to function on the Arria10 devkit.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
k2l netcp range size is 16M (0x1000000) and not 0xffffff. This patch fixes
this. Similarly fix the size of switch module register space to 0x20000.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
k2e netcp range size is 16M (0x1000000) and not 0xffffff. This patch fixes
this. Similarly fix the size of switch module register space to 0x20000.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
k2hk netcp range size is 1M (0x100000) and not 0xfffff. This patch fixes
this.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
This patch enables networking on k2l evm by providing
device bindings for netcp, knav, and qmss. See device
binding documentation at
Documentation/devicetree/bindings/net/keystone-netcp.txt
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add boot_secondary implementation for the Arria10 platform. Bringing up
the secondary core on the Arria 10 platform is pretty similar to the
Cyclone/Arria 5 platform, with the exception of the following differences:
- Register offset to bringup CPU1 out of reset is different.
- The cpu1-start-addr for Arria10 contains an additional nibble.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Convert cyclone5/arria5 to use CPU_METHOD_OF_DECLARE for smp operations.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
No need to cast the void pointer returned by kmalloc() in
arch/arm/kvm/mmu.c::kvm_alloc_stage2_pgd().
Signed-off-by: Firo Yang <firogm@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Saui
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge omap fixes for v4.1, urgent fix to avoid potential hardware damage From Tony Lindgren:
Omap fixes for the -rc cycle, including a fix for potential hardware
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
* tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
pci_dma_burst_advice() was added by e24c2d963a ("[PATCH] PCI: DMA
bursting advice") but apparently never used. Remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <monstr@monstr.eu> # microblaze
CC: David S. Miller <davem@davemloft.net>
Add ioremap_wt() to all arch-specific asm/io.h headers which
define ioremap_wc() locally. These headers do not include
<asm-generic/iomap.h>. Some of them include <asm-generic/io.h>,
but ioremap_wt() is defined for consistency since they define
all ioremap_xxx locally.
In all architectures without Write-Through support, ioremap_wt()
is defined indentical to ioremap_nocache().
frv and m68k already have ioremap_writethrough(). On those we
add ioremap_wt() indetical to ioremap_writethrough() and defines
ARCH_HAS_IOREMAP_WT in both architectures.
The ioremap_wt() interface is exported to drivers.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The driver for the PCIe controller was just added, this adds the
missing definition of the IRQ numbers to device tree. The driver itself
will be automatically detected by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the NAND flash chip description for a standard chip found
connected to this SoC. This makes use of generic Broadcom NAND driver
with the iProc interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When dma-coherent transfers are enabled, the mmap call must
not change the pg_prot flags in the vma struct.
Split the arm_dma_mmap into a common and specific parts,
and add a "arm_coherent_dma_mmap" implementation that does
not alter the page protection flags.
Tested on a topic-miami board (Zynq) using the ACP port
to transfer data between FPGA and CPU using the Dyplo
framework. Without this patch, byte-wise access to mmapped
coherent DMA memory was about 20x slower because of the
memory being marked as non-cacheable, and transfer speeds
would not exceed 240MB/s.
After this patch, the mapped memory is cacheable and the
transfer speed is again 600MB/s (limited by the FPGA) when
the data is in the L2 cache, while data integrity is being
maintained.
The patch has no effect on non-coherent DMA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes the TCM initialisation code to handle TCM banks that are
present but inaccessible due to TrustZone configuration. This is
the default case when enabling the non-secure world. It may also
be the case that that the user decided to use TCM for TrustZone.
This change has exposed a bug in handling of TCM where no TCM bank
was usable (the 0 size TCM case). This change addresses the
resulting hang.
This code only handles the ARMv6 TCMTR register format, and will not
work correctly on boards that use the ARMv7 (or any other) format.
This is handled by performing an early exit from the initialisation
function when the TCMTR reports any format other than v6.
Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When using a toolchain with gold as the default linker, the VDSO build
fails:
VDSO arch/arm/vdso/vdso.so.raw
HOSTCC arch/arm/vdso/vdsomunge
MUNGE arch/arm/vdso/vdso.so.dbg
OBJCOPY arch/arm/vdso/vdso.so
BFD: arch/arm/vdso/vdso.so: Not enough room for program headers, try
linking with -N
For whatever reason, ld.gold is omitting an exidx program header that
ld.bfd emits, and even when I work around that, I don't get a working
VDSO.
For now, instead of supporting gold (which will fail to link the
kernel anyway since it does not implement --pic-veneer), direct the
compiler to use the traditional bfd linker. This is accomplished by
using -fuse-ld, which is implemented in GCC 4.8 and later.
Note: one limitation of this is that if the toolchain is configured
to use gold by default, and the bfd linker is not in $PATH, the VDSO
build will fail:
VDSO arch/arm/vdso/vdso.so.raw
collect2: fatal error: cannot find 'ld'
This will happen if CROSS_COMPILE begins with a path such as
/opt/bin/arm-linux-gnu- but /opt/bin is not in $PATH. This is
considered an acceptable corner-case limitation and is easily worked
around.
Additonal note: we use cc-option instead of cc-ldoption so that
-fuse-ld=bfd is placed in the command line if the compiler recognizes
the option. Using cc-ldoption results in an attempt to link, which
fails in the situation just described, causing -fuse-ld=bfd to be
omitted and gold to be used for the VDSO link, which is what we're
trying to prevent.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the VDSO's link options are kind of a mess spread between
ccflags-y and cmd_vdsold. Collect linker directives into one
variable, VDSO_LDFLAGS, and use that in cmd_vdsold.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's quite a lot here, most of it from Mark Rutland, who has been
working on big.LITTLE PMU support for a while now. His work also brings
us significantly closer to moving the bulk of the CPU PMU driver out
into drivers/, where it can be shared with arm64.
As part of this work, there is a small patch to perf/core, which has
been Acked-by PeterZ and doesn't conflict with tip/perf/core at present.
I've kept that patch on a separate branch, merged in here, so that the
tip guys can pull it too if any unexpected issues crop up.
Please note that there is a conflict with mainline, since we remove
perf_event_cpu.c. The correct resolution is also to remove the file,
since the changes there are already reflected in the rework (and this
resolution is already included in linux-next).
SYSMMU devices are registered very early in arch_initcall, so ensure
that they can get access to power domains by registering power domain
driver from earlier initcall. This change requires dropping usage of
the platform device associated with each power domain and replacing
clock calls with respective of_clk_* equivalents.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
PS_HOLD based power off procedure is common for all Exynos SoCs,
so use it for every Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The platform_device_id is not modified by the driver and core
uses it as const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The irq_domain_ops are not modified by the driver and the irqdomain
core code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The following patch adds coupled cpuidle support for Exynos3250 to
an existing cpuidle-exynos driver. As a result it enables AFTR mode
to be used by default on Exynos3250 without the need to hot unplug
CPU1 first.
The detailed changelog:
- use exynos_[get,set]_boot_addr() in cpuidle-exynos.c and then make
cpu_boot_reg_base() static
- use exynos_core_restart() in exynos_cpu0_enter_aftr()
- add missing smp_rmb() to exynos_cpu0_enter_aftr() (to make the code
in-sync with the platform SMP code)
- add call_firmware_op(cpu_boot, 1) to exynos_cpu0_enter_aftr()
- use dsb_sev() instead of IPI wakeup for Exynos3250 in
exynos_cpu0_enter_aftr()
- add CPU0 vs CPU1 synchronization based on S5P_PMU_SPARE2 register
for Exynos3250 to cpuidle-exynos.c
- add flush_cache_all() for CPU1/0 before powerdown/AFTR for
Exynos3250 to exynos_wfi_finisher()/exynos_do_idle()
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add get_cpu_boot_addr() firmware operation and then
exynos_get_boot_addr() helper.
This is a preparation for adding coupled cpuidle support
for Exynos3250 SoC.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add exynos_set_boot_addr() helper and covert existing code
(exynos_boot_secondary() and exynos_smp_prepare_cpus()) to
use it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
There is a kernel message about secondary CPU bootup when
exynos_core_restart() is called through CPU hotplug code-path (the
only exynos_core_restart() user currently) so there is no need for
an extra info on Exynos3250 SoC about software reset. This also
prepares exynos_core_restart() to be re-used in coupled cpuidle
code-path in the future.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
exynos_boot_secondary() can erroneously return 0 or -ENOSYS even
when waiting on pen_release being set to -1 timeouts. Fix it by
adjusting ret variable value to -ETIMEDOUT when necessary.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Using a fixed (by DTS) parent for clocks when turning on the power
domain may introduce issues in other drivers. For example when such
driver changes the parent during runtime and expects that he is the
only place of such change.
Do not rely on DTS providing the fixed parent for such clocks. Instead
before switching domain off, grab a current parent of a clock with
clk_get_parent().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework. Removes this warning on probe:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:889 __clk_enable+0x28/0x9c()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.19.0+ #46
[<c0013a98>] (unwind_backtrace) from [<c0010d8c>] (show_stack+0x10/0x14)
[<c0010d8c>] (show_stack) from [<c001b018>] (warn_slowpath_common+0x7c/0xa4)
[<c001b018>] (warn_slowpath_common) from [<c001b0d0>] (warn_slowpath_null+0x18/0x20)
[<c001b0d0>] (warn_slowpath_null) from [<c01a5f80>] (__clk_enable+0x28/0x9c)
[<c01a5f80>] (__clk_enable) from [<c01a600c>] (clk_enable+0x18/0x2c)
[<c01a600c>] (clk_enable) from [<c001860c>] (s3c_adc_probe+0x11c/0x18c)
[<c001860c>] (s3c_adc_probe) from [<c0153a10>] (platform_drv_probe+0x30/0x78)
[<c0153a10>] (platform_drv_probe) from [<c01523e0>] (driver_probe_device+0xb0/0x1fc)
[<c01523e0>] (driver_probe_device) from [<c01525dc>] (__driver_attach+0x68/0x88)
[<c01525dc>] (__driver_attach) from [<c0150df0>] (bus_for_each_dev+0x70/0x94)
[<c0150df0>] (bus_for_each_dev) from [<c0151c80>] (bus_add_driver+0xdc/0x1c4)
[<c0151c80>] (bus_add_driver) from [<c0152ba4>] (driver_register+0x9c/0xe0)
[<c0152ba4>] (driver_register) from [<c03041cc>] (adc_init+0x10/0x34)
[<c03041cc>] (adc_init) from [<c00087fc>] (do_one_initcall+0x110/0x1cc)
[<c00087fc>] (do_one_initcall) from [<c02ffccc>] (kernel_init_freeable+0xf4/0x1ac)
[<c02ffccc>] (kernel_init_freeable) from [<c022f4fc>] (kernel_init+0x8/0xe0)
[<c022f4fc>] (kernel_init) from [<c000e098>] (ret_from_fork+0x14/0x3c)
---[ end trace f4a1ea39a114fecf ]---
Signed-off-by: Sergiy Kibrik <sakib@meta.ua>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add missing of_node_put() to:
1. Error return path if allocating memory for exynos_pm_domain failed.
2. Second iteration over power domains if a child domain was not
present or was incomplete.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Prevent possible NULL pointer dereference of pointer returned by
of_find_device_by_node(). Handle this by skipping such power domain.
Additionally fail the init on kstrdup() failure. Such case is actually
not fatal because the name for power domain allocated by kstrdup() is
used only in printk. Still as a precaution handle this as an error
condition.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Prevent possible NULL pointer dereference if of_iomap() fails.
Handle the error by skipping such power domain.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the bootargs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The kizbox dts are using the deprecated linux,stdout-path. Replace those by
stdout-path.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gaël PORTAY <g.portay@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add RTC support to the at91sam9rlek.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The RTC lives at 0xfffffe00. Also reorder the node properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AM57xx Beagle X15 has a HDMI output. This patch adds the device tree
nodes required for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
DRA72 EVM has a HDMI output. This patch adds the device tree nodes
required for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
DRA7xxx contains a very similar DSS to OMAP5. The main differences are:
* no DSI or RFBI support.
* 1 or 2 dedicated video PLLs.
* need to do additional configuration to the DRA7 CONTROL module.
DRA72xx has only one video PLL, and DRA74xx has two.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Simplify the DSS detection logic by creating a list of the omapdss
compat strings, instead of checking each separately with an 'if'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Set DSS core hwmod as the parent for all the DSS submodules. This
ensures that the parent hwmods are enabled before any DSS submodules are
accessed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Add DMM hwmod entries for DRA7. This is identical to DMM on OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
We need set-rate-parent flags for the display's clock path so that the
DSS driver can change the clock rate of the PLL.
This patchs adds the ti,set-rate-parent flag to 'dss_dss_clk' clock
node, which is only a gate clock, allowing the setting of the clock rate
to propagate to the PLL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tero Kristo <t-kristo@ti.com>
This patch adds System MMU nodes to all defined devices that are
specific to Exynos5420/5800/5422 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes to all defined devices that are
specific to Exynos5250 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes to all defined devices that are
specific to Exynos4415 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes to the devices that are specific to
Exynos3250 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes that are specific to Exynos4210/4x12
series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add a new Linux clock for DRA7 based SoCs to control DESHDCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
The i.MX6DL/S GPT has a different programming model from i.MX6Q one.
Add the compatible string "fsl,imx6dl-gpt" for it, and leave
"fsl,imx6q-gpt" there to keep the existing/old kernel happy.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for the imx6dl based aristainetos2 board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
MReset cause: POR
MBoard: aristaitenos2
DRAM: 1 GiB
NAND: 1024 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lb07wv8 (800x480)
As this board can be used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Arrange the license text a bit to make it clear.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also add label for backlight_lvds and connect it to the LVDS display.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also add label for backlight_lvds and connect it to the display.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx7d intergrates the unique display controller for EPD panel, pixel engines
and graphics engines to make it a ideal solution for EPD based devices such
as eReader, Signage, as well as any application rely on the bistable charactersic
of the EPD panel.
imx7d include two ARM Cortex A7 Core and one Cortex-M4 core.
Included Main Peripheral
- DDR3\LP-DDR2
- GPMI\BCH\APBH DMA(NAND flash support)
- QSPI
- WEIM Nor
- LCDIF\MIPI DSI
- CSI\MIPI CSI
- EPDC
- PCIe RC\EP
- USB OTG\Host
- CAN x2
- I2C x4
- SIMv2 x2
- ENET -x2
- uSDHC x3
- eCSPI x1
- PWM x4
- OCOTP (fuse)
- GPT x4
- WDOG x4
- Flex Timer x2
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This commit includes a minor nomenclature fixup for boards based on the
Freescale VF610 SoC and which make use of the alternate "RMII1_RXD1"
functionality for pin PTC12. This brings the macro name in-line with
both the datasheet and other similar macros.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add DT support for the Broadcom Wifi/Bluetooth devices found on the
microsom board.
[Modified original Russell King's patch to use mmc-pwrseq]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Jon Nettleton <jon@solid-run.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CODA960 VPU is part of the PU power domain. Add power-domains
phandle so it can be associated with the PU generic pm domain for
power gating.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
For more details see:
http://www.gateworks.com/product/item/ventana-gw5510-single-board-computer
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USBOTG1 always work on peripheral mode and USBOTG in host mode, so fix
their roles accordingly.
Tested by mounting the MMC card as a storage device:
modprobe g_mass_storage file=/dev/mmcblk0p2
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to the warp schematics there are no regulators for the USB OTG
ports, so let's remove them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The 'reg_1p8v' regulator is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch updates the in tree-users of the SSD1306 controller for using
the newly introduced DT properties.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add PCIe support. Based on a patch from Rabeeh Khoury from the solid-run
tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx23-olinuxino board has an i2c interface exposed on UEXT connector.
This patch enables i2c and selects the pin group used on UEXT connector.
Tested with MOD-LCD1x9 from Olimex.
This patch is based on work by Fadil Berisha with his permission. However
all bugs are mine.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx23-olinuxino board has an i2c interface exposed on UEXT connector.
This patch provides the generic devicetree infrastructure for a follow-up
patch to add support to the actual board files.
Tested all three possible pin groups with MOD-LCD1x9 from Olimex.
This patch is based on work by Fadil Berisha with his permission. However
all bugs are mine.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6qdl-hummingboard boards use sgtl5000 codec and the machine file
(imx-sgtl5000) already sets SSI in slave mode and codec in master mode, so there
is no need for having the 'fsl,mode' property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently the HDMI controller is a child device of the AIPS bus in the
DT which is clearly wrong. Move it to the right location.
This introduces no functional change it just aligns the DT representation
with reality.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Like i.MX6, the i.MX7 code calls into the anatop driver, which fails
if that is disabled:
arch/arm/mach-imx/built-in.o: In function `imx7d_init_machine':
arch/arm/mach-imx/mach-imx7d.c:24: undefined reference to `imx_anatop_init'
arch/arm/mach-imx/built-in.o: In function `imx7d_init_irq':
arch/arm/mach-imx/mach-imx7d.c:29: undefined reference to `imx_init_revision_from_anatop'
This patch ensures that for an imx7-only build, we still get anatop
built-in, matching what we do for imx6. We also need to select
HAVE_IMX_MMDC, as that is needed by the anatop code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on imx timer driver, now it's ready to be moved into
drivers/clocksource/. Let's do it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It splits irq enable/disable/acknowledge operations into device specific
functions as the hooks in imx_gpt_data, so that we can save the use of
timer_is_xxx() and cpu_is_xxx() checking in these irq functions.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We now have pointer to imx_timer structure available where timer base
address is needed, so we can just kill global timer_base by using
imxtm->base instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It defines offset of gpt registers TSTAT, TCN and TCMP per device
type in imx_gpt_data, so that these registers can be accessed in an
way without timer_is_v2() checking.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since we now have imx_timer structure, it makes more sense to move those
clock event related variables into the structure, so that we can save
some global variables.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It creates a gpt device speicific data structure and adds function hook
gpt_setup_tctl in there to set up gpt TCTL register.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use different initialization function in CLOCKSOURCE_OF_DECLARE() to
initialize gpt device type for DT boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Define an enum for gpt timer device type in include/soc/imx/timer.h to
tell the gpt block differences among SoCs. Update non-DT users (clock
drivers) to pass the device type.
As we now have include/soc/imx/timer.h, the declaration of
mxc_timer_init() is moved into there as the best fit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of passing around as individual argument, let's move timer
resources like irq and clocks together with base address into a data
structure, and pass pointer of the structure as argument to simplify
the function call interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Replace the __raw_readl/__raw_writel with readl_relaxed/writel_relaxed
which is endian-safe, as a step of moving the driver code into folder
drivers/clocksource.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
A recent change to the imx53 power management caused a build
regression when CONFIG_SOC_IMX53 is disabled:
mach-imx/built-in.o:(.init.rodata+0x60): undefined reference to `imx53_suspend'
mach-imx/built-in.o:(.init.rodata+0x64): undefined reference to `imx53_suspend_sz'
This avoids the problem by compiling the code in question
conditionally on the presence of CONFIG_SOC_IMX53. For
consistency, I'm also changing the same thing for
CONFIG_SOC_IMX51.
An additional benefit of this approach is reduced code size
for kernels that only include support for one of the two
SoCs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1579c7b9fe ("ARM: imx53: Set DDR pins to high impedance when in suspend to RAM.")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use the generic mechanism to declare a bitmap instead of unsigned long.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In order to save power the DDR pins should be put into high
impedance when in suspend to RAM.
This requires manually requesting self refresh (rather than using the
automatic mode implemented by the CCM / ESDCTL), followed by
reconfiguring the IOMUXC.
Of course the code to do this cannot itself run from DDR so the
code is copied to and executed from internal memory.
In my tests using a custom i.MX53 board with LPDDR2 RAM
this reduced the suspend power consumption from 200mW to 60mW.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add low level uart debug support for imx7d
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Include the "common.h" header file to fix the following sparse warning:
arch/arm/mach-imx/mmdc.c:66:5: warning: symbol 'imx_mmdc_get_ddr_type' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The comments were corrected as the following to reflect
the real situation of Freescale MXC timer IP block.
There are totally 4 version of the timer on Freescale i.MX SoCs.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Removed the duplicated function declaration of mxc_timer_init
which was already declared in drivers/clk/imx/clk.h.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 4631960d26da ("ARM: imx6: set initial power mode in pm function")
moves imx6_set_lpm() from clock init function into
imx6_pm_common_init(). This causes a hang when cpuidle support is
enabled. The reason for that is ARM core clock is shut down
unexpectedly by WAIT mode. It happens with the following call stack:
cpuidle_register_governor()
cpuidle_switch_governor()
cpuidle_uninstall_idle_handler()
synchronize_sched()
wait_rcu_gp()
wait_for_completion()
When wait_for_completion() is called as above, all cores are idle/WFI.
Hence, the reset value of CCM_CLPCR_LPM - WAIT mode, will trigger a
hardware shutdown of the ARM core clock.
To fix the regression, we need to ensure that CCM_CLPCR_LPM is
initialized into RUN mode earlier than cpuidle governor registration,
which is a postcore_initcall. This patch creates function
imx6_pm_ccm_init() to map CCM block and initialize CCM_CLPCR_LPM into
RUN mode, and have the function called from machine .init_irq hook,
which should be early enough.
Reported-by: Kevin Hilman <khilman@kernel.org>
Fixes: 8fb76a07e2 ("ARM: imx6: set initial power mode in pm function")
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
With the cleanup done before, we now can simply define base address and
irq as needed in clock driver, to get those platform header inclusions
removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of calling cpu_is_xxx() in clk-pllv1 driver, let's add clk-pllv1
type support to handle the difference/quirk in particular SoC designs.
Doing so will help get clk-pllv1 driver ready for being moved out of
arch/arm/mach-imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As we're about to move clock drivers out of arch/arm/mach-imx,
cpu_is_xxx() shouldn't be used any more. Let's avoid the call by
looking at the device tree machine compatible string to determine
which SoC the clock driver is running on.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Kevin Hilman