mdio's dev field needs to be set before mdio ops occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio's dev field needs to be set before mdio ops occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qeth_clear_output_buffer for HiperSockets may not clear
all 16 SBALEs, but only the used ones. The error flag in SBALF15
has to be cleared in any case.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HiperSocket devices receive-path checksumming is not required.
Thus NO_CHECKSUMMING is used as default for HiperSocket interfaces.
For layer3 devices configured with NO_CHECKSUMMING received skbs
should have set their ip_summed field to CHECKSUM_UNNECESSARY.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
z/VM Virtual Switch Port Isolation allows guests on a VLAN UNAWARE
virtual switch to be isolated from other guests on the VSWITCH.
(See z/VM Apars VM64281 and VM64463).
The Linux qeth driver is affected, because it has to handle new
error codes introduced with the z/VM VSWITCH Port Isolation support.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels are already removed when setting a ctcm-device offline.
Thus ctcm_remove_device must not refer to channel information.
Solution: delete channel information from the trace call in
ctcm_remove_device.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qeth device is plugged off, setting the device online stops in
state HARDSETUP and a failure is reported to the base cio-layer
causing halt/clear to be invoked. Replugging the device again triggers
a qeth recovery without notification of the cio-layer. If a device
is ungrouped in this state, the qeth set_offline function is not
invoked, because the corresponding ccwgroup device is not in state
ONLINE. Then incoming traffic is still handled by the qdio layer
resulting in a crash in qeth_l<x>_qdio_input_handler, because (part
of) the qeth data structures for this device are already removed.
Solution: After replugging the device qeth recovery should lead to a
working net device. Thus a "LAN offline" result when setting a qeth
device online must not report a failure to the base cio-layer.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is always discarded anyway but lets just set this to our
safest lowest.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_regd_init() needs to be called with the wiphy already
properly set with the bands. Without this the custom regulatory
settings were not taking effect, and the device would get
the default channel settings from ath9k_[25]ghz_chantable.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report status unknown as if there were successfully transmitted.
This will avoid hostapd to disassociate because it doesn't understand what a status unknown is.
Signed-off-by: Alexandre Becholey <alexandre.becholey@epfl.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 does not set PM field for normal data frames, so we need to
update that based on the current PS mode when using PS-Poll
(timeout=0) power save mode.
This allows the AP to remain in sync with our PS state. However, there
is still a potential race condition between PS state changes when
multiple TX queues are used and nullfunc and PS-Poll frames use
different queue. That corner case may need to be handled separately by
changing which queue is used either in ath9k or mac80211.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must make sure the chip is awake when changing the RX filter
parameters. This could have caused problems, e.g., when changing the
interface to promiscuous mode while in sleep mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the chip complains about TSF sync, make sure we remain awake to
sync with the next Beacon frame. In theory, this should not be needed
since we are currently trying to receive all Beacon frames, anyway,
better have this code ready should we ever change that.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is in sleep mode, there is no point trying to calibrate
the radio since it will just results in incorrect values being read
from registers and other potential issues. In addition, if we actually
start processing calibrate, do not allow the chip to be put into sleep
until we have completed the calibration step.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using timeout=0 (PS-Poll) with mac80211, the driver will need to
wake up for TX requests and remain awake until the TX has been
completed (ACK received or timeout) or until the buffer frame(s) have
been received (in case the TX is for a PS-Poll frame).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are trying to interpolate a curve with slope == 0, the return
value will always be the y-coordinate. In this code we are looping
until we reach a minimum y-coordinate on a line, which in the 0-slope
case can never happen, thus the loop never terminates.
The PCDAC steps come from the EEPROM and should never be equal, but
we should gracefully handle that case, so warn and bail out.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix to set dev->broadcast correctly, since
dev->broadcast is defined as:
unsigned char broadcast[MAX_ADDR_LEN];
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix this build error:
drivers/staging/agnx/pci.c: In function 'agnx_config_interface':
drivers/staging/agnx/pci.c:315: error: dereferencing pointer to incomplete type
..
drivers/staging/agnx/pci.c:424: error: unknown field 'config_interface' specified in initializer
config_interface was removed in 2d0ddec5b2
("mac80211: unify config_interface and bss_info_changed")
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not need to do this in ath_isr() and it looks like the modified
version ends up being more stable as far as being able receive beacon
frames is concerned. Furthermore, this reduces need to move between
AWAKE and NETWORK SLEEP states when processing some unrelated
interrupts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently all radios receive all traffic on the simulated air
if they are tuned to the same channel. This patch introduces
the concept of grouping, which allows to assign a radio to
certain group. Only radios in the same group can 'see' each other.
Each bit in /debug/ieee80211/phy*/hwsim/group
represents one group. By default all radios belong to the same group "1",
e.g. bit 1 is set. Additionally a radio can belong to several groups.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k only generated the beacon when bss_info_changed() was called,
but for AP mode this is not enough, because the TIM IE would never
get updated and consequently PS mode clients wouldn't know about
buffered frames. Instead, get a new beacon on every SWBA interrupt.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drop test for FW_STATE_RESET in p54spi_work as fw_state
is never assigned this value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process beacon change even if the BSSID doesn't
change at the same time. Also fix what I think
is a small locking error in b43legacy, there's
a spin_unlock_irqrestore that looks out of place.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under high load first data word, read after available data size
is sometimes lost in p54spi_rx. It seems to depend on frequency
of interrupts and latency of data read request relatively to
'data available' interrupt. The worst consequence of this bug
is loss of packet transmission acknowledgement, which in turn
causes overflow of tx queues and permanent link loss.
Read data size and first data word in one SPI transaction.
No packets from LMAC should have length less than 1 word,
so this shouldn't interfere with the next read transaction.
Also call p54spi_sleep if p54spi_wake succeeded.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put chip into sleep state, once it's been awaken.
Also, propagate error code to the caller.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return whether wakeup operation succeeded.
Make use of this return value.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When SPI write of odd length is requested, p54spi_write splits it
into two parts: one for all data, except the last byte, and one
for last byte and padding byte. Unfortunately, the length of
first part is not amended. It works because all meaningful bytes
have proper value and the last byte of odd length SPI write
transaction is ignored.
p54spi_work has dummy HOST_INTERRUPTS register read at the end.
Drop it, as its result is not used and it has no side effects.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Host is not allowed to modify DMA_WRITE_CTRL register
if bit HOST_ALLOWED in it is not set. Wait for HOST_ALLOWED first.
Also get rid of timeout in p54spi_wait_bit as it's been playing
a role of workaround for such an incorrect register access.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliminate direct accesses to the driver_data field.
cf 82ab13b26f15f49be45f15ccc96bfa0b81dfd015
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device *dev;
expression E;
type T;
@@
- dev->driver_data = (T)E
+ dev_set_drvdata(dev, E)
@@
struct device *dev;
type T;
@@
- (T)dev->driver_data
+ dev_get_drvdata(dev)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is one of the incremental steps for unifying iwl_station_entry
for all HWs, i.e. removing of iwl3945_station_entry
This patch drops iwl3945_tid_data and use iwl_tid_data instead.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces struct iwl3945_hw_key by struct iwl_hw_key.
It's not used directly with any host command therefore removal is trivial
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes unnecessary MMIO accesses in the interrupt hotpath. The
patch by Michael Buesch for b43 has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures the beacon timers with beacon interval
and beacon period passed through vif.bss_conf. Also cache the
currecnt beacon configuration which will be used to configure
the beacon timers when the driver triggers it after reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous implementation was moving back to NETWORK SLEEP state
immediately after receiving a Beacon frame. This means that we are
unlikely to receive all the buffered broadcast/multicast frames that
would be sent after DTIM Beacon frames. Fix this by parsing the Beacon
frame and remaining awake, if needed, to receive the buffered
broadcast/multicast frames. The last buffered frame will trigger the
move back into NETWORK SLEEP state.
If the last broadcast/multicast frame is not received properly (or if
the AP fails to send it), the next Beacon frame will work as a backup
trigger for returning into NETWORK SLEEP.
A new debug type, PS (debug=0x800 module parameter), is added to make
it easier to debug potential power save issues in the
future. Currently, this is only used for the Beacon frame and buffered
broadcast/multicast receiving.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes use of the local fc variable in bit more places and uses a
common helper macro. The part of RX process that delivers skb's to
mac80211 is moved to a separate function in preparation for future
changes that will need to do this from two places. The modifications
here should not result in any functional changes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The broadcast bit is in the first, not the last octet..
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to my tests, all that ZD_CS_MULTICAST does is to
disable retrying/waiting for an ACK. Reflect this by renaming
the bit to ZD_CS_NO_ACK and setting it based on
IEEE80211_TX_CTL_NO_ACK, instead of is_multicast_ether_addr.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are not correctly listening to the regulatory max bandwidth
settings. To actually make use of it we need to redesign things
a bit. This patch does the work for that. We do this to so we
can obey to regulatory rules accordingly for use of HT40.
We end up dealing with HT40 by having two passes for each channel.
The first check will see if a 20 MHz channel fits into the channel's
center freq on a given frequency range. We check for a 20 MHz
banwidth channel as that is the maximum an individual channel
will use, at least for now. The first pass will go ahead and
check if the regulatory rule for that given center of frequency
allows 40 MHz bandwidths and we use this to determine whether
or not the channel supports HT40 or not. So to support HT40 you'll
need at a regulatory rule that allows you to use 40 MHz channels
but you're channel must also be enabled and support 20 MHz by itself.
The second pass is done after we do the regulatory checks over
an device's supported channel list. On each channel we'll check
if the control channel and the extension both:
o exist
o are enabled
o regulatory allows 40 MHz bandwidth on its frequency range
This work allows allows us to idependently check for HT40- and
HT40+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not go beyond ARRAY_SIZE of intf->crypto_stats
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"airo: airo_get_encode{,ext} potential buffer overflow" was actually a
no-op, due to an unrecognized type overflow in an assignment. Oddly,
gcc only seems to tell me about it when using -Wextra...grrr...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling cancel_delayed_work() from inside
spin_lock_irqsave, introduces a potential deadlock.
As explained by Johannes Berg <johannes@sipsolutions.net>
A - lock
T - timer
phase CPU 1 CPU 2
---------------------------------------------
some place that calls
cancel_timer_sync()
(which is the | code)
lock-irq(A)
| "lock-irq"(T)
| "unlock"(T)
| wait(T)
unlock(A)
timer softirq
"lock"(T)
run(T)
"unlock"(T)
irq handler
lock(A)
unlock(A)
Now all that again, interleaved, leading to deadlock:
lock-irq(A)
"lock"(T)
run(T)
IRQ during or maybe
before run(T) --> lock(A)
"lock-irq"(T)
wait(T)
We fix this by moving the call to cancel_delayed_work() into workqueue.
There are cases where the work may not actually be queued or running
at the time we are trying to cancel it, but cancel_delayed_work() is
able to deal with this.
Also cleanup iwl_set_mode related to this call. This function
(iwl_set_mode) is only called when bringing interface up and there will
thus not be any scanning done. No need to try to cancel scanning.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13224, which was also
reported at http://marc.info/?l=linux-wireless&m=124081921903223&w=2 .
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e8f055f0c3 ("ath5k: Update reset code") subtly changed the
code that computes floating point values for the PHY3_TIMING register
such that the exponent is off by a decimal point, which can cause
problems with OFDM channel operation.
get_bitmask_order() actually returns the highest bit set plus one,
whereas the previous code wanted the highest bit set. Instead, use
ilog2 which is what this code is really calculating. Also check
coef_scaled to handle the (invalid) case where we need log2(0).
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.
The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GRO/LRO can be controlled through ethtool so this is unnecessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow myri10ge LRO to be enabled/disabled via ethtool
(and by the stack for packet forwarding).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is purely a cleanup patch. This collapses some of the code required
when we configure our Tx and Rx feature sets, and makes the code more
readable and maintainable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFF specification for Direct Attach cable detection has now been
ratified. Previously, DA cable detect was looking at the Twinaxial bit in
byte 9 of the SFP+ EEPROM. The spec now defines active and passive DA
cables in byte 8 of the SFP+ EEPROM. This patch changes the cable
detection for both 82598 and 82599 SFP+ adapters to conform to the new
spec.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFP+ NIC (device id 0x10fb) needs a semaphore to serialize
PHY access, so our PHY init code must honor that same semaphore.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to mostly historic reasons, including a lack of reliability
of the link handling (especially with the older 8169), the
current r8169 driver emulates forced mode setting by limiting
the advertised modes.
With this change the driver allows real 10/100 forced mode
settings on the 8169 and 8101/8102.
Original idea by Vincent Steenhoute. The RTL_GIGA_MAC_VER_03
tweak was extracted from Realtek's r8169 v6.010.00 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek pointed pppoe can call back dev_queue_xmit(), and might need
skb->dst, so its safer to unset IFF_XMIT_DST_RELEASE on ppp devices.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One point of contention in high network loads is the dst_release() performed
when a transmited skb is freed. This is because NIC tx completion calls
dev_kree_skb() long after original call to dev_queue_xmit(skb).
CPU cache is cold and the atomic op in dst_release() stalls. On SMP, this is
quite visible if one CPU is 100% handling softirqs for a network device,
since dst_clone() is done by other cpus, involving cache line ping pongs.
It seems right place to release dst is in dev_hard_start_xmit(), for most
devices but ones that are virtual, and some exceptions.
David Miller suggested to define a new device flag, set in alloc_netdev_mq()
(so that most devices set it at init time), and carefuly unset in devices
which dont want a NULL skb->dst in their ndo_start_xmit().
List of devices that must clear this flag is :
- loopback device, because it calls netif_rx() and quoting Patrick :
"ip_route_input() doesn't accept loopback addresses, so loopback packets
already need to have a dst_entry attached."
- appletalk/ipddp.c : needs skb->dst in its xmit function
- And all devices that call again dev_queue_xmit() from their xmit function
(as some classifiers need skb->dst) : bonding, vlan, macvlan, eql, ifb, hdlc_fr
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sysfs files for a network device can not unconditionally take the
rtnl_lock as the bonding sysfs files do. If someone accesses those
sysfs files while the network device is being unregistered with the
rtnl_lock held we will deadlock.
So use trylock and restart_syscall to avoid this problem.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered. So use trylock and syscall_restart to avoid this
deadlock.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pdev->irq was not saved in netxen_adapter, causing request_irq()
with invalid irq number.
This was broken in commit be339aee63
("netxen: fix irq tear down and msix leak.").
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Per Dalen <per.dalen@cnw.se>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for the one or two channel CPC-PCI and CPC-PCIe
cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Markus Plessing <plessing@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver adds support for the SJA1000 chips connected to the
"platform bus", which can be found on various embedded systems.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the generic Socket-CAN driver for the Philips SJA1000
full CAN controller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CAN network device driver interface provides a generic interface to
setup, configure and monitor CAN network devices. It exports a set of
common data structures and functions, which all real CAN network device
drivers should use. Please have a look to the SJA1000 or MSCAN driver
to understand how to use them. The name of the module is can-dev.ko.
Furthermore, it adds a Netlink interface allowing to configure the CAN
device using the program "ip" from the iproute2 utility suite.
For further information please check "Documentation/networking/can.txt"
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TI DaVinci EMAC driver.
TI DaVinci Ethernet Media Access Controller module is based upon
TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on
some TI devices. It supports MII/RMII and has up to 8Kbytes of internal
descriptor memory. This driver has been working on several TI devices including
DM644x, DM646x and DA830 platforms. The specs of this device are available at:
http://www.ti.com/litv/pdf/sprue24a
Signed-off-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marching along, let's bump the version number to indicate things actually
have happened to the driver.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the generic XAUI device support for 82599 controllers.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The performance of hardware RSC is greatly reduced if the total for max rsc
descriptors multiplied by the buffer size is greater than 65535. To
prevent this we need to adjust the max rsc descriptors appropriately.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ram Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the
mv643xx_eth driver brings an interface up. The following patch makes
the driver work on my Pegasos again; it is mostly a search and replace
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.
Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in DCB mode, switching between link flow control and priority
flow control shouldn't need to reset the hardware. This removes that
reset.
This also extends the set_all() dcbnl callback to return a value indicating
that the HW config changed, however a reset was not required.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool should report that link flow control is disabled when in priority
flow control mode.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 supports using either link flow control or priority flow control when
in DCB mode. The dcbnl interface already supports sending down
configurations through rtnetlink that can enable LFC when DCB is enabled,
so the driver should take advantage of this.
82598 does not support using LFC when DCB is enabled, so explicitly disable
it when we're in DCB mode. This means we always run in PFC mode when DCB
is enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sets the low water threshhold for priority flow control for 82598
and 82599 controllers in DCB mode.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable jumbo frame when FCoE feature is enabled in 82599. Use 3K
as the receive queue buffer size for receive queues used by FCoE
to address for max Fiber Channel frame size as 2148 bytes (with
max 2112 bytes of payload).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable using FCoE redirection table feature in 82599. The FCoE
redirection table has maximum of eight entries, corresponding
to maximum of eight receive queues to be used for distributing
incoming FCoE packets. This patch sets up the FCoE redirection
table when multiple receive queues are available for FCoE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ring feature for FCoE to make use of the FCoE redirection
table in 82599. The FCoE redirection table is a receive side
scaling feature for Fiber Channel over Ethernet feature in 82599,
enabling distributing FCoE packets to different receive queues
based on the exchange id.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we can find a type NETDEV_HW_ADDR_T_SAN mac address from the
corresponding netdev for a fcoe interface then sets up added the
fc->ctlr.spma flag and stores spma mode address in ctl_src_addr.
In case the spma flag is set then:-
1. Adds spma mode MAC address in ctl_src_addr as secondary
MAC address, the FLOGI for FIP and pre-FIP will go out
using this address.
2. Cleans up stored spma MAC address in ctl_src_addr in
fcoe_netdev_cleanup.
3. Sets up spma bit in fip_flags for FIP solicitations along
with exiting FPMA bit setting.
4. Initialize the FLOGI FIP MAC descriptor to stored spma
MAC address in ctl_src_addr. This is used as proposed
FCoE MAC address from initiator along with both SPMA
and FPMA bit set in FIP solicitation, in response the
switch may grant any FPMA or SPMA mode MAC address to
initiator.
Removes FIP descriptor type checking against ELS type
ELS_FLOGI in fcoe_ctlr_encaps to update a FIP MAC descriptor,
instead now checks against FIP_DT_FLOGI.
I've tested this with available FPMA-only FCoE switch but
since data_src_addr is updated using same old code for
both FPMA and SPMA modes with FIP or pre-FIP links, so added
SPMA mode will work with SPMA-only switch also provided that
switch grants a valid MAC address.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently fcoe_netdev_config adds netdev pkt handler for fcoe pkts,
fcoe_if_create adds netdev pkt handler for fip packets, a secondary
MAC address is added by fcoe_netdev_config and then later cleanup
for these netdev related config/adds is done only during
fcoe_if_destroy and no cleanup done on error during fcoe interface
creation after above netdev config calling in fcoe_if_create.
So this patch adds single func for above mentioned cleanup the
fcoe_netdev_cleanup and then calls this func on either fcoe interface
destroy or exiting from fcoe_if_create due to an error after fcoe/fip
related above netdev config is done.
Moved netdev pkt handler addition code blocks for fip pkts close to
similar code block for foce pkt in fcoe_netdev_config, so that added
fcoe_netdev_cleanup could be called on error from fcoe_netdev_config
to undo these both additions for fcoe/fip pkt handlers. This move
required reference to fcoe_fip_recv in fcoe_netdev_config, so moved
fip related functions fcoe_fip_recv, fcoe_fip_send and
fcoe_update_src_mac above fcoe_netdev_config.
This consolidation will enable spma mode support in next patch to
easily add or delete spma mode mac address beside fixing current
no cleanup issue during error.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After acquiring the SAN MAC address from the EEPROM, we need to program it
into one of the RARs. Also, DCB will use this MAC address to run DCBX
commands, so it doesn't have to play musical MAC addresses when things like
bonding enter the picture. So we need to return the MAC address through
the netlink interface to userspace.
This also moves the init_rx_addrs() call out of start_hw() and into
reset_hw(). We shouldn't try to read any of the RAR information before
initializing our internal accounting of the RAR table, which was what
was happening.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the Storage Address entrypoint from the net device.
It will read the SAN MAC addresses from the EEPROM of the 82599 hardware,
and make them available to the FCoE stack through the net device.
Also, add/del the SAN MAC address to the netdev dev_addr_list via the
kernel api dev_addr_add()/dev_addr_del() when there is a valid SAN MAC
supported by the HW.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove DE620_DEBUG and de620_debug.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove de600_debug as it is not needed.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc95xx driver was forwarding the trailing fcs on received frames
up the stack leading to confusion in tcpdump.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments describing the rx/tx headers used a combination of zero-
and 1-based indexing, leading to confusion.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net_device trans_start field is a hot spot on SMP and high performance
devices, particularly multi queues ones, because every transmitter dirties
it. Is main use is tx watchdog and bonding alive checks.
But as most devices dont use NETIF_F_LLTX, we have to lock
a netdev_queue before calling their ndo_start_xmit(). So it makes
sense to move trans_start from net_device to netdev_queue. Its update
will occur on a already present (and in exclusive state) cache line, for
free.
We can do this transition smoothly. An old driver continue to
update dev->trans_start, while an updated one updates txq->trans_start.
Further patches could also put tx_bytes/tx_packets counters in
netdev_queue to avoid dirtying dev->stats (vlan device comes to mind)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The B channel data structure member rcvbytes was never set to
anything else but zero, so drop it.
Impact: cleanup
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the kernel config option GIGASET_UNDOCREQ, permanently
activating the code it controlled, as there have been no reports
of problems caused by its activation but many problems caused by
it being disabled.
Also fix a few bad comments while we're at it.
Impact: cleanup
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for porting to kernel CAPI subsystem, include the
Gigaset driver's Kconfig directly from ISDN's instead of I4L's.
Impact: Kconfig reorganisation, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
gigaset_register_to_LL() is expected to print a message and return 0
on failure. Make it do so consistently.
Impact: error handling bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't generate the hex representation of the payload data if it
isn't actually used afterwards.
Impact: optimization
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_warning() / pr_err() instead of dev_warn() / dev_err() in two
places where the dev pointer isn't guaranteed to be valid.
Impact: error handling bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The separation of state tables for base and M10x has long been
removed. Clean up remaining traces of it.
Impact: cleanup
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi structures are being created each time we open a port, but when
the port is closed the napi structure is only disabled but not removed.
This bug caused hang while removing the driver.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using bnx2 in a high transmit load, bnx2_tx_int() cost is pretty high.
There are two reasons.
One is an expensive call to bnx2_get_hw_tx_cons(bnapi) for each freed skb
One is cpu stalls when accessing skb_is_gso(skb) / skb_shinfo(skb)->nr_frags
because of two cache line misses.
(One to get skb->end/head to compute skb_shinfo(skb),
one to get is_gso/nr_frags)
This patch :
1) avoids calling bnx2_get_hw_tx_cons(bnapi) too many times.
2) makes bnx2_start_xmit() cache is_gso & nr_frags into sw_tx_bd descriptor.
This uses a litle bit more ram (256 longs per device on x86), but helps a lot.
3) uses a prefetch(&skb->end) to speedup dev_kfree_skb(), bringing
cache line that will be needed in skb_release_data()
result is 5 % bandwidth increase in benchmarks, involving UDP or TCP receive
& transmits, when a cpu is dedicated to ksoftirqd for bnx2.
bnx2_tx_int going from 3.33 % cpu to 0.5 % cpu in oprofile
Note : skb_dma_unmap() still very expensive but this is for another patch,
not related to bnx2 (2.9 % of cpu, while it does nothing on x86_32)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->dev_addr changed from being an array to being a pointer, so we
should not take its address for memcpy().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds FCoE related statistics to 82599, including number Rx-ed and Tx-ed
FCoE packets, number of Rx-ed and Tx-ed FCoE packets in dwords, number of bad
Fiber Channel CRCs detected in FCoE packets, and number of FCoE packets dropped
on the Rx side.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the FCoE Rx side offload feature in ixgbe_main.c
to 82599 using the Rx offload infrastructure code added in the previous
patch. The large receive offload by Direct Data Placement (DDP) for
FCoE is achieved by implementing the ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done
in net_device_ops via netdev. It is up to the ULD, i.e., fcoe and libfc
to query and setup large receive offload accordingly through the corresponding
netdev upon creating fcoe instances.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds infrastructure code for FCoE Rx side offload feature to
82599, which provides large receive offload for FCoE by Direct
Data Placement (DDP). The ixgbe_fcoe_ddp_get() and ixgbe_fcoe_ddp_put()
pair corresponds to the netdev support to FCoE by the function pointers
provided in net_device_ops as ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done.
The implementation of these in ixgbe is shown in the next patch.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the FCoE Tx side offload features in ixgbe_main.c
to 82599 using the Tx offload infrastructure code added in the previous
patch. This is achieved by the calling the FCoE Sequence Offload (FSO)
function ixgbe_fso() on the transmit path of ixgbe.
This patch also includes an EEPROM check to make sure the NIC we're loading
on is an offload-enabled SKU.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds infrastructure code for FCoE Tx side offload feature to
82599, including Fiber Channel CRC calculation, auto insertion of
the start of frame (SOF) and end of frame (EOF) of FCoE packets,
and large send by FCoE Sequence Offload (FSO).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the FCoE feature code ixgbe_fcoe.c to 82599. For a start, this patch
only adds ixgbe_configure_fcoe() to configure related register for FCoE to 82599.
In patches that follow, I will be adding more functions to ixgbe_fcoe.c to add
support of FCoE offload features to 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the FCoE feature header ixgbe_fcoe.h to 82599. This header includes
the defines and structures required by the ixgbe driver to support various
offload features in 82599 for Fiber Channel over Ethernet (FCoE). These offloads
features include Fiber Channel CRC calculation, FCoE SOF/EOF auto insertion,
FCoE Sequence Offload (FSO) for large send, and Direct Data Placement (DDP)
for large receive.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds FCoE related register defines to 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPC_MULTIPLATFORM was killed in commit 28794d3 but this stale occurrence was
hiding the mv643xx_eth driver in some cases (e.g. Pegasos II)
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i386 allmodconfig:
drivers/net/82596.c: In function 'init_rx_bufs':
drivers/net/82596.c:544: warning: cast to pointer from integer of different size
drivers/net/82596.c:545: warning: cast to pointer from integer of different size
drivers/net/82596.c:548: warning: cast to pointer from integer of different size
drivers/net/82596.c:557: warning: cast to pointer from integer of different size
drivers/net/82596.c:565: warning: cast to pointer from integer of different size
drivers/net/82596.c:569: warning: cast to pointer from integer of different size
drivers/net/82596.c:575: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'rebuild_rx_bufs':
drivers/net/82596.c:606: warning: cast to pointer from integer of different size
drivers/net/82596.c:608: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'init_i596_mem':
drivers/net/82596.c:680: warning: cast to pointer from integer of different size
drivers/net/82596.c:681: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_rx':
drivers/net/82596.c:818: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_add_cmd':
drivers/net/82596.c:975: warning: cast to pointer from integer of different size
drivers/net/82596.c:979: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_start_xmit':
drivers/net/82596.c:1088: warning: cast to pointer from integer of different size
drivers/net/82596.c:1099: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_interrupt':
drivers/net/82596.c:1404: warning: cast to pointer from integer of different size
(ugh)
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change error message when alloc_cpumask_var fails.
Repairs "cpumask: convert drivers/net/sfc".
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch fixes issues with dev->dev_addr changing from array to pointer.
Hopefully there are no others.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
piix: The Sony TZ90 needs the cable type hardcoding
icside: register second channel of version 6 PCB
ide-tape: remove back-to-back REQUEST_SENSE detection
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Jonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c10726 (ide: add struct ide_host
(take 3)).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Processor idle power states C2 and C3 stop the TSC on many machines.
Linux recognizes this situation and marks the TSC as unstable:
Marking TSC unstable due to TSC halts in idle
But if those same machines are booted with "processor.max_cstate=1",
then there is no need to validate C2 and C3, and no need to
disable the TSC, which can be reliably used as a clocksource.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
A previous 2.6.30 patch, a71e4917dc,
(ACPI: idle: mark_tsc_unstable() at init-time, not run-time)
erroneously disabled the TSC on systems that did not actually
have valid deep C-states.
Move the check after the deep-C-states are validated,
via new helper, tsc_check_state(), hich replaces tsc_halts_in_c().
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Frans Pop <elendil@planet.nl>
If the BIOS hands us an invalid throttling state,
write a valid state.
http://bugzilla.kernel.org/show_bug.cgi?id=13259
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce module parameter processor.ignore_tpc.
Some laptops are shipped with buggy _TPC,
this module parameter is used to to disable the buggy support.
http://bugzilla.kernel.org/show_bug.cgi?id=13259
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'
http://bugzilla.kernel.org/show_bug.cgi?id=13165
Signed-off-by: Len Brown <len.brown@intel.com>
In 2.6.29,
31878dd86b
"ACPI: remove BM_RLD access from idle entry path"
moved BM_RLD initialization to init-time from run time.
But we discovered that some BIOS do not restore BM_RLD
after suspend, causing device errors on C3 and C4
after resume. So now the kernel restores BM_RLD.
http://bugzilla.kernel.org/show_bug.cgi?id=13032
Signed-off-by: Len Brown <len.brown@intel.com>
The BIOS bug workaround mistakenly got disabled
when we followed the ACPI specification more closely
by ignoring OS updates to that bit.
(The BIOS is supposed to update SCI_EN, not the OS)
http://bugzilla.kernel.org/show_bug.cgi?id=13289
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI MSI: Fix MSI-X with NIU cards
PCI: Fix pci-e port driver slot_reset bad default return value
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add new GET_PIPE_FROM_CRTC_ID ioctl.
drm/i915: Set HDMI hot plug interrupt enable for only the output in question.
drm/i915: Include 965GME pci ID in IS_I965GM(dev) to match UMS.
drm/i915: Use the GM45 VGA hotplug workaround on G45 as well.
drm/i915: ignore LVDS on intel graphics systems that lie about having it
drm/i915: sanity check IER at wait_request time
drm/i915: workaround IGD i2c bus issue in kernel side (v2)
drm/i915: Don't allow binding objects into the last page of the aperture.
drm/i915: save/restore fence registers across suspend/resume
drm/i915: x86 always has writeq. Add I915_READ64 for symmetry.
* 'upstream-linus' of ssh://master.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Media rotation rate and form factor heuristics
libata: Report disk alignment and physical block size
sata_fsl: Fix the command description of FSL SATA controller
sata_fsl: Fix compile warnings
[libata] sata_sx4: fixup interrupt handling
[libata] sata_sx4: convert to new exception handling methods
* git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
iwlwifi: fix device id registration for 6000 series 2x2 devices
ath5k: update channel in sw state after stopping RX and TX
rtl8187: use DMA-aware buffers with usb_control_msg
mac80211: avoid NULL ptr deref when finding max_rates in PID and minstrel
airo: airo_get_encode{,ext} potential buffer overflow
Pulled directly by Linus because Davem is off playing shuffle-board at
some Alaskan cruise, and the NULL ptr deref issue hits people and should
get merged sooner rather than later.
David - make us proud on the shuffle-board tournament!
This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.
The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard. Only then are the
characteristics reported to SCSI via the VPD B1 page.
This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever. With no complaints so far.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For disks with 4KB sectors, report the correct block size and alignment
when filling out the READ CAPACITY(16) response.
This patch is based upon code from Matthew Wilcox' 4KB ATA tree. I
fixed the bug I reported a while back caused by ATA and SCSI using
different approaches to describing the alignment.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'. This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We we build with dma_addr_t as a 64-bit quantity we get:
drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Issuing ATA_CMD_SET_FEATURES (0xef) times out because
pdc20621_interrupt ignores command completion since
ATA_TFLAG_POLLING flag is set.
This has already been fixed for sata_promise:
commit 51b94d2a5a
Author: Tejun Heo <htejun@gmail.com>
Date: Fri Jun 8 13:46:55 2007 -0700
sata_promise: use TF interface for polling NODATA commands
Also, this patch includes Mikael's original patches:
http://marc.info/?l=linux-ide&m=121135828227724&w=2http://marc.info/?l=linux-ide&m=121144512109826&w=2
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: gdb documentation fix
kgdb,i386: use address that SP register points to in the exception frame
sysrq, intel_fb: fix sysrq g collision
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix PCI ROM access
powerpc/pseries: Really fix the oprofile CPU type on pseries
serial/nwpserial: Fix wrong register read address and add interrupt acknowledge.
powerpc/cell: Make ptcal more reliable
powerpc: Allow mem=x cmdline to work with 4G+
powerpc/mpic: Fix incorrect allocation of interrupt rev-map
powerpc: Fix oprofile sampling of marked events on POWER7
powerpc/iseries: Fix pci breakage due to bad dma_data initialization
powerpc: Fix mktree build error on Mac OS X host
powerpc/virtex: Fix duplicate level irq events.
powerpc/virtex: Add uImage to the default images list
powerpc/boot: add simpleImage.* to clean-files list
powerpc/8xx: Update defconfigs
powerpc/embedded6xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/fsl_soc: Remove mpc83xx_wdt_init, again
Commit 79e539453b introduced a
regression where you cannot use sysrq 'g' to enter kgdb. The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics. The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.
This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The receive interrupt routine checks the wrong register if the
receive fifo is empty. Further an explicit interrupt acknowledge
write is introduced. In some circumstances another interrupt was
issued.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the i2400m receives data and the device indicates there has to be
reordering, we keep an sliding window implementation to sort the
packets before sending them to the network stack.
One of the "operations" that the device indicates is "queue a packet
and update the window start". When the queue is empty, this is
equivalent to "deliver the packet and update the window start".
That case was optimized in i2400m_roq_queue_update_ws() so that we
would not pointlessly queue and dequeue a packet. However, when the
optimization was active, it wasn't updating the window start. That
caused the reorder management code to get confused later on with what
seemed to be wrong reorder requests from the device.
Thus the fix implemented is to do the right thing and update the
window start in both cases, when the queue is empty (and the
optimization is done) and when not.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC. Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: Eric Anholt <eric@anholt.net>
We detect HDMI output connection status by writing to HOT Plug Interrupt
Detect Enable bit in PORT_HOTPLUG_EN. The behavior will generate a specified
interrupt, which is caught by audio driver, but during one detection driver
set all Detect Enable bits of HDMIB, HDMIC HDMID, and generate wrong
interrupt signals for current output, according to the signals audio driver
misunderstand device status. The patch intends to handle corresponding
output precisely.
It fixed freedesktop.org bug #21371
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It fixed bug #21659
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-applied because git-am is too picky]
Signed-off-by: Eric Anholt <eric@anholt.net>
Although spec say CRT_HOTPLUG_ACTIVATION_PERIOD_64 is only useful for
mobile platform, it is also required to detect vga on G4x desktops correctly.
Tested on G45/G43/Q45 platforms with no regressions.
It fixed freedesktop.org bug #21120 and part of bug #21210
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are a number of small form factor desktop systems with Intel mobile
graphics chips that lie and say they have an LVDS. With kernel mode-setting,
this becomes a problem, and makes native resolution boot go haywire -- for
example, my Dell Studio Hybrid, hooked to a 1920x1080 display claims to
have a 1024x768 LVDS, and the resulting graphical boot on the 1920x1080
display uses only the top left 1024x768, and auto-configured X will end
up only 1024x768 as well. With this change, graphical boot and X
both do 1920x1080 as expected.
Note that we're simply embracing and extending the early bail-out code
in place for the Mac Mini here. The xorg intel driver uses pci subsystem
device and vendor id for matching, while we're using dmi lookups here.
The MSI addition is courtesy of and tested by Bill Nottingham.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We might sleep here anyway so I hope an extra uncached read is ok to
add.
In #20896 we found that vbetool clobbers the IER. In KMS mode this is
particularly bad since we don't set the interrupt regs late (in
EnterVT), so we'd fail to get *any* interrupts at all after X started
(since some distros have scripts that call vbetool at X startup
apparently).
So this patch checks IER at wait_request time, and re-enables
interrupts if it's been clobbered. In a proper config this check
should never be triggered.
This is really a distro issue, but having a sanity check is nice, as
long as it doesn't have a real performance hit.
Tested-by: Mateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Moved the check inside of the sleeping case to avoid perf cost]
Signed-off-by: Eric Anholt <eric@anholt.net>
In IGD, DPCUNIT_CLOCK_GATE_DISABLE bit should be set, otherwise i2c
access will be wrong.
v2: Disable CLOCK_GATE_DISABLE bit after bit bashing as suggested by Eric.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This should avoid a class of bugs where the hardware prefetches past the
end of the object, and walks into unallocated memory when the object is
bound to the last page of the aperture.
fd.o bug #21488
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch fixes a regression caused by commit
b1569e99c7
"ACPI: move thermal trip handling to generic thermal layer"
which accidentally changed trip point trigger condition to
temp > trip_temp
This patch changes the trigger condition back to
temp >= trip_temp
Signed-off-by: Vladimir Zajac <eightgraph@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
If there is a failure during eeepc_hotk_add() we need
to remove the acpi_notify_handler.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
KEY_STOP is now KEY_STOPCD
It's the correct key to stop a media
BTN_EXTRA is now KEY_SCREENLOCK:
The laptop manual tells us that this key is for screenlock
KEY_TV is now KEY_PROG1
So it can be reported to X server
Ref: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/361505
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The older eeepc-acpi driver allowed to control the SHE performance
preset through a ACPI function for just this purpose. SHE underclocks
and undervolts the FSB and undervolts the CPU (at preset 2,
"powersave"), or slightly overclocks the CPU (at preset 0,
"performance"). Preset 1 is the default setting with default clocks and
voltage.
The new eeepc-laptop driver doesn't support it anymore.
The attached patch adds support for it to eeepc-laptop. It's very
straight-forward and almost trivial.
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
1) Buggy firmware can change the RFKILL state by itself. This is easily
detected. The RFKILL API states that in such cases, we should call
rfkill_force_state() to notify the core.
I have reported the bug to Asus. I believe this is the right thing
to do for robustness, even if this particular firmware bug is fixed.
2) The same bug causes the wireless toggle key to be reported as 0x11
instead of 0x10. 0x11 is otherwise unused, so it should be safe to
add this as a new keycode.
The bug is triggered by removing the laptop battery while hibernated.
On resume, the wireless toggle key causes the firmware to toggle the
wireless state itself. (Also, the key is reported as 0x11 when the
current wireless state is OFF).
This is very poor behaviour because the OS can't predict whether the
firmware is controlling the RFKILL state.
Without this workaround, the bug means users have to press the wireless
toggle key twice to enable, due to the OS/firmware conflict. (Assuming
rfkill-input or equivalent is being used). The workaround avoids this.
I believe that acpid scripts which toggle the value of the sysfs state file
when the toggle key is pressed will be rendered ineffective by the bug,
regardless of this workaround. If they simply toggle the state, when the
firmware has already toggled it, then you will never see a state change.
Tested on "EEEPC 4G" only.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
This maps the brightness control events to one of two keys, either
KEY_BRIGHTNESSDOWN or KEY_BRIGHTNESSUP, as needed.
Some mapping has to be done due to the fact that the BIOS reports them as
<base value> + <current brightness index>; the selection is done according to
the sign of the change in brightness (if this is 0, no keypress is reported).
(Ref. http://lists.alioth.debian.org/pipermail/debian-eeepc-devel/2009-April/002001.html)
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
When an rfkill device is registered, the rfkill core will change its
state to the system default. So we need to prepare for state changes
*before* we register it. That means installing the eeepc-specific ACPI
callback which handles the hotplug of the wireless network adaptor.
This problem doesn't occur during normal operation. You have to
1) Boot with wireless enabled. eeepc-laptop should load automatically.
2) modprobe -r eeepc-laptop
3) modprobe eeepc-laptop
On boot, the default rfkill state will be set to enabled.
With the current core code, step 2) will disable the wireless.
Therefore in step 3), the wireless will change state during registration,
from disabled to enabled. But without this fix, the PCI device for the
wireless adaptor will not appear.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The following symbols are needlessly defined global:
default_mode
default_var
gbe_mem_phys
gbe_turn_off
gbefb_exit
gbefb_init
gbefb_setup
This error was noticed by namespacecheck when compiling ip32_defconfig.
This patch makes the symbols static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Don't overwrite fast registration page list when posting work request
RDMA/cxgb3: Don't complete flushed send work requests twice
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: add NOGET quirk for devices from CH Products
HID: fix dropped device-specific quirks
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dma: fix ipu_idmac.c to not discard the last queued buffer
ioatdma: fix "ioatdma frees DMA memory with wrong function"
ipu_idmac: Use disable_irq_nosync() from within irq handlers.
dmatest: fix max channels handling
This also fixes the case of a single queued buffer, for example, when taking a
single frame snapshot with the mx3_camera driver.
Reported-by: Agustin Ferrin Pozuelo <gatoguan-os@yahoo.com>
Tested-by: Agustin Ferrin Pozuelo <gatoguan-os@yahoo.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
as reported by Alexander Beregalov <a.beregalov@gmail.com>
ioatdma 0000:00:08.0: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000007f76f800] [size=2000 bytes]
[map
ped as single] [unmapped as page]
The ioatdma driver was unmapping all regions
(either allocated as page or single) using unmap_page.
This patch lets dma driver recognize if unmap_single or unmap_page should be used.
It introduces two new dma control flags:
DMA_COMPL_SRC_UNMAP_SINGLE and DMA_COMPL_DEST_UNMAP_SINGLE.
They should be set to indicate dma driver to do dma-unmapping as single
(first one for the source, tha latter for the destination).
If respective flag is not set, the driver assumes dma-unmapping as page.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix a bug in viafb on x86_64 builds (e.g. for VIA Nano CPU).
You cannot make the assumption that sizeof(unsigned int) ==
sizeof(unsigned long), so the parsing of the default mode (640x480) fails,
leading to a division by zero during insmod of the driver.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: <JosephChan@via.com.tw>
Cc: <ScottFang@viatech.com.cn>
Cc: Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The required I2C modules are now selected automatically by the means
of select statements in Kconfig, so there is no point in confusing the
users with options he/she would be supposed to enable manually.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables the alarm interrupt of TWL4030 RTC to wake up the
system from suspend. You can test this patch with following command.
# echo +10 > /sys/class/rtc/rtc0/wakealarm; echo mem > /sys/power/state;
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
setup() may fail before ctldata is set, causing a kernel panic on
cleanup().
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-2630-rc5' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-cpm: Pass dev ptr to dma_*_coherent rather than NULL
i2c: Enable i2c-s3c2410 for S3C64XX too
i2c-mpc: bug fix for MPC52xx clock setting and printout
i2c-pxa.c: timeouts off by 1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc2007 - fix locking in hrtimer handler
Input: atkbd - add force release keys quirk for Amilo Xi 3650
Input: ff-memless - fix signed to unsigned bit overflow
Input: joydev - blacklist digitizers
People keep getting bitten by this, so just auto-select it by default,
assuming most configurations will actually want a console.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the return after the goto. We want the goto because it frees
memory as well as returning err.
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The NIU device refuses to allow accesses to MSI-X registers before MSI-X
is enabled. This patch fixes the problem by moving the read of the mask
register to after MSI-X is enabled.
Reported-by: David S. Miller <davem@davemloft.net>
Tested-by: David S. Miller <davem@davemloft.net>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Recent DMA changes result in a BUG() when NULL is passed to
dma_alloc_coherent in place of a device.
Signed-off-by: Mark Ware <mware@elphinstone.net>
[ben-linux@fluff.org: fix patch moves]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This controller is also present on the S3C64xx series processors so
enable the driver in Kconfig for those platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clock setting did not work for the MPC52xx due to a stupid bug.
Furthermore, the dev info output "clock=0" for old device trees was
misleading. This patch fixes both issues.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now that hrtimers are always running in hard irq context we can't
unconditionally enable interrupts at the end of the timer function.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: The Sony TZ90 needs the cable type hardcoding
ata_piix: ICH7 does not support correct MWDMA timings
Avoid world-writable sysfs files in libata driver.
libata: fix suspend/resume for ATA SEMB devices
libata: clear ering on resume
pata_pdc202xx_old: fix UDMA33 handling
sata_mv: use new sata phy register settings for new devices
libata: fix attach error handling
This patch makes the return type of some of the functions
void as those functions always return true
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show current qos AC parameters in sysfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add "rate_scale_data" debugfs file to show current bit rate (HT and Legacy),
plus additional information (rssi, noise, tsf, beacon time stamp).
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hard coded value, use the define in iwl-commands.h for
better code maintenance
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read rev id in nic_config instead of nic_init.
Nic_config has some checking for rev_id but we actually don't read
the rev_id in there.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Somehow these pre-production cards are showing up in the community.
With this message we hope that it will be clear that the hardware is not
supported.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn rate scaling will periodically search other rate scale
tables to switch to the best table regarding performance. In the past
the number of search tables were 3. Every time the rate scale algorithm
goes through these available tables in will stay in current table for
some time before start searching again. Recent driver support more
feature and antenna, so we have more tables to search. This patch make
sure we go through all available tables.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes all the dead code that tries to adjust the power
saving level based on the system AC state (inacceptable policy
in the kernel) or based on overtemp conditions (unused).
Also, pass _all_ policy wrt. enabling PS to mac80211, since
we do not use the power_disabled internally I now use that to
mirror the mac80211 CONF_PS setting. When mac80211 turns off
CONF_PS we follow suit. This means that the user power level
(which can currently only be set from sysfs) is not touched
for mac80211 powersave changes.
This means no "association status" checks are necessary since
mac80211 will not allow power save to be enabled when not
associated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi internally needs to keep track of whether PS
is enabled in the firmware or not. To do this, it keeps
a bit in the status flags, called STATUS_POWER_PMI.
The code to set this bit looks as follows:
static int iwl_set_power(struct iwl_priv *priv, void *cmd)
{
return iwl_send_cmd_pdu_async(priv, POWER_TABLE_CMD,
sizeof(struct iwl_powertable_cmd),
cmd, NULL);
}
int iwl_power_update_mode(...)
{
[...]
if (final_mode != IWL_POWER_MODE_CAM)
set_bit(STATUS_POWER_PMI, &priv->status);
iwl_update_power_cmd(priv, &cmd, final_mode);
cmd.keep_alive_beacons = 0;
if (final_mode == IWL_POWER_INDEX_5)
cmd.flags |= IWL_POWER_FAST_PD;
ret = iwl_set_power(priv, &cmd);
if (final_mode == IWL_POWER_MODE_CAM)
clear_bit(STATUS_POWER_PMI, &priv->status);
else
set_bit(STATUS_POWER_PMI, &priv->status);
if (priv->cfg->ops->lib->update_chain_flags && update_chains)
priv->cfg->ops->lib->update_chain_flags(priv);
[...]
}
Now, this bit really needs to track what the _firmware_
thinks, not what the driver thinks. Therefore, there is
a race condition here -- the driver sets the bit before
it knows that the async command sent to the card in the
iwl_set_power function has been processed. As a result,
the call to update_chain_flags() may think that the card
has been woken up (PMI bit cleared) while in reality it
hasn't processed the async POWER_TABLE_CMD yet.
This leads to bugs -- any commands the update_chain_flags
function sends can get stuck and subsequent commands also
fail.
The fix is almost trivial: since there's no reason to send
an async command here (in fact, there almost never should
be since many mac80211 callbacks can sleep) just make the
function wait for the card to process the command and then
return and clear the PMI bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the microcode fails for any reason, ask mac80211 to
recover instead of trying ourselves and failing at it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no need to have a separate struct for a
single variable. The fact that it exists is due to the
code legacy, but we can remove that now. Very simple.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower 4 bytes of the chipset revision must contain
a non-zero value. This bug was introduced by
"rt2x00: Simplify rt2x00_check_rev".
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not needed outside iwl-core.c
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
m68k allmodconfig:
| drivers/net/wireless/wl12xx/main.c: In function 'wl12xx_probe':
| drivers/net/wireless/wl12xx/main.c:1273: error: implicit declaration of function 'set_irq_type'
| make[1]: *** [drivers/net/wireless/wl12xx/main.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add device ids for 2x2 devices. Also fix antenna usage because these devices use
antennas A and B, not B and C.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Feeding the return code of get_wep_key directly to the length parameter
of memcpy is a bad idea since it could be -1...
Reported-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
See Errata documentation. The recommended workaround is to use PIO4 instead
which will we automatically do by flagging this mode not available.
Signed-off-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
79b42babba fixed identifying ATA devices
reporting 3c/c3 signature which belongs to SEMB devices now. However,
suspending the machine with such device (WDC WD2500AAJS-6 01.0) fails
with the following:
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/66 mode selected
sd 1:0:0:0: [sda] Starting disk
ata5: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata4: softreset failed (device not ready)
ata4: failed due to HW bug, retry pmp=0
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2: limiting SATA link speed to 1.5 Gbps
ata4.00: configured for UDMA/133
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2.00: disabled
sd 1:0:0:0: rejecting I/O to offline device
sd 1:0:0:0: [sda] START_STOP FAILED
sd 1:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
PM: Device 1:0:0:0 failed to thaw: error 65536
sd 3:0:0:0: [sdb] Starting disk
due to a class mismatch in ata_dev_revalidate(). Fix it by adding the
ATA_DEV_SEMB device class to the check.
CC: Tejun Heo <htejun@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Error timestamps are in jiffies which doesn't run while suspended and
PHY events during resume isn't too uncommon. When the two are
combined, it can lead to unnecessary speed downs if the machine is
suspended and resumed repeatedly. Clear error history on resume.
This was reported and verified in bnc#486803 by Vladimir Botka.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Vladimir Botka <vbotka@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The original driver doesn't use 66 MHz clock for UDMA33.
[ The alternative solution would be to adjust UDMA33 timings
for 66 MHz clock but I think that it is safer to stick with
old & tested behavior for now. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Marvell's new SoC (65 nano) needs different settings for its SATA
PHY registers.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New device attach path in ata_eh_revalidate_and_attach() is divided
into two separate loops because ATA requires IDENTIFY to be issued to
slave first while the user expects to see device probe messages from
the master device. new_mask is used to track which devices are the
new ones between the first loop and the second.
This usually works well but if an error occurs during configuration
stage, ata_dev_revalidate_and_attach() returns with error code and
forgets new_mask. On the retry run, dev->class is set and new_mask
for the device is clear, so the device just gets revalidated and thus
ends up skipping post-configuration procedure including scheduling of
SCSI_HOTPLUG for the device. When this occurs, ATA part of probing
works fine but SCSI probing usually doesn't happen and makes the
device unreachable.
The behavior has been around for a very long time but it has been
uncovered with the recent addition of 1_5_GBPS horkage which uses
-EAGAIN return value from ata_dev_configure() to restart the probing
sequence after forcing cable speed.
This can be fixed by making sure dev->class is permanently set only
after all configurations are successfully complete. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tim Connors <tconnors+linuxkml@astro.swin.edu.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch (as1240) adds the NOGET quirk for three devices from CH
Products: the Pro pedals, the Combatstick joystick, and the Flight-Sim
yoke. Without these quirks, the devices haven't worked for many
kernel releases. Sometimes replugging them after boot-up would get
them to work and sometimes they wouldn't work at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sean Hildebrand <silverwraithii@gmail.com>
Reported-by: Sid Boyce <sboyce@blueyonder.co.uk>
Tested-by: Sean Hildebrand <silverwraithii@gmail.com>
Tested-by: Sid Boyce <sboyce@blueyonder.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Device-specific quirks are set up correctly in their respective vendor-specific
driver, then get overwritten in usbhid_parse().
This is only issue for device-specific NOGET quirks being set by driver for a
few devices out there.
Signed-off-by: Zoltan Karcagi <zkr@freemail.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PAGE_MASK is 0xFFFFF000 on i386 -- even with PAE.
So it's not sufficient to ensure that you use phys_addr_t or uint64_t
everywhere you handle physical addresses -- you also have to avoid using
the construct 'addr & PAGE_MASK', because that will strip the high 32
bits of the address.
This patch avoids that problem by using PHYSICAL_PAGE_MASK instead of
PAGE_MASK where appropriate. It leaves '& PAGE_MASK' in a few instances
that don't matter -- where it's being used on the virtual bus addresses
we're dishing out, which are 32-bit anyway.
Since PHYSICAL_PAGE_MASK is not present on other architectures, we have
to define it (to PAGE_MASK) if it's not already defined.
Maybe it would be better just to fix PAGE_MASK for i386/PAE?
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: comedi: David doesn't want to get comedi patches
Staging: rtl8187se: Fix compilation warnings and procfs directory leak
Staging: rt2870: new device id
Staging: w35und: unregister device from the ieee80211 stack upon ->disconnect()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
usb-serial: ftdi_sio: fix reference counting of ftdi_private
USB: unusual_devs: extend nokia 6288 bcd range
USB: Gadget: fix UTF conversion in the usbstring library
USB: Fix makefile so that CONFIG_WDM and CONFIG_TMC work.
USB: ftdi_sio: add vendor/product id for the Marvell SheevaPlug
USB: cxacru: Fix negative dB output
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Revert driver core: move platform_data into platform_device
Revert driver core: fix passing platform_data
Remove old PRINTK_DEBUG config item
Doc/sysfs-rules: Swap the order of the words so the sentence makes more sense
Driver core: platform: fix kernel-doc warnings
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (22 commits)
Fix the race between capifs remount and node creation
Fix races around the access to ->s_options
switch ufs directories to ufs_sync_file()
Switch open_exec() and sys_uselib() to do_open_filp()
Make open_exec() and sys_uselib() use may_open(), instead of duplicating its parts
Reduce path_lookup() abuses
Make checkpatch.pl shut up on fs/inode.c
NULL noise in fs/super.c:kill_bdev_super()
romfs: cleanup romfs_fs.h
ROMFS: romfs_dev_read() error ignored
fs: dcache fix LRU ordering
ocfs2: Use nd_set_link().
Fix deadlock in ipathfs ->get_sb()
Fix a leak in failure exit in 9p ->get_sb()
Convert obvious places to deactivate_locked_super()
New helper: deactivate_locked_super()
reiserfs: remove privroot hiding in lookup
reiserfs: dont associate security.* with xattr files
reiserfs: fixup xattr_root caching
Always lookup priv_root on reiserfs mount and keep it
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
bonding: fix panic if initialization fails
IXP4xx: complete Ethernet netdev setup before calling register_netdev().
IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
ipvs: Fix IPv4 FWMARK virtual services
ipv4: Make INET_LRO a bool instead of tristate.
net: remove stale reference to fastroute from Kconfig help text
net: update skb_recycle_check() for hardware timestamping changes
bnx2: Fix panic in bnx2_poll_work().
net-sched: fix bfifo default limit
igb: resolve panic on shutdown when SR-IOV is enabled
wimax: oops: wimax_dev_add() is the only one that can initialize the state
wimax: fix oops if netlink fails to add attribute
Bluetooth: Move dev_set_name() to a context that can sleep
netfilter: ctnetlink: fix wrong message type in user updates
netfilter: xt_cluster: fix use of cluster match with 32 nodes
netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
netfilter: add missing linux/types.h include to xt_LED.h
mac80211: pid, fix memory corruption
mac80211: minstrel, fix memory corruption
cfg80211: fix comment on regulatory hint processing
...
This patch adds three attribute files in /sys/class/net/$dev/ for tun
devices; allowing userspace to obtain the information which TUNGETIFF
offers, and more, but without having to attach to the device in question
(which may not be possible if it's in use).
It also fixes a bug which has been present in the TUNGETIFF ioctl since
its inception, where it would never set IFF_TUN or IFF_TAP according to
the device type. (Look carefully at the code which I remove from
tun_get_iff() and how the new tun_flags() helper is subtly different).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/home/v4l/master/v4l/cafe_ccic.c: In function 'cafe_cam_init':
/home/v4l/master/v4l/cafe_ccic.c:778: warning: statement with no effect
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: saeed bishara <saeed.bishara@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to an uninitialized chip.ident field the chip identification failed.
Thanks-to: Saeed Bishara <saeed.bishara@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_TUNER_MODE_ was used in a few places where V4L2_TUNER_SUB_ should have
been used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Found the coccinelle tool.
Thanks-to: Julia Lawall <julia@diku.dk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 2.6.30 kernel generates this warning:
uvc_driver.c:1729: warning: 'ret' may be used uninitialized in this function
I guess some new warning flag must have been turned on since this warning
didn't appear with older kernels (gcc version 4.3.1). It's also a bogus
warning, but since this code didn't comply to the coding standard anyway
I've modified it to 1) remove the warning and 2) conform to the coding
standard.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The boards control struct wasn't updated when (presumably) all of the
other drivers migrated from using scode_table to specifying the demod.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ioctls have structs that are a different size depending on what type
of buffer is being used. If the buffer type leaves a field unused or has
padding space at the end, this space should be zeroed out.
The problems with S_FMT and REQBUFS were original identified and patched by
Marton Nemeth <nm127@freemail.hu>.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For a number of different ioctls, the v4l2-ioctl code checks that the
passed buffer type is supported by the driver. It did this by checking
that the driver defined a method for the try_fmt handler for that buffer
type. However, try_fmt is optional and a driver might not provide it even
though it does support that type. So use g_fmt instead, since that isn't
optional.
This should fix a problem with VBI capture with saa7146.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If someone requests a format at fmt->index == (unsigned)-1 and the first
format in the array doesn't have the requested type then num will still be
-1 when it's compared to fmt->index and there will appear to be a match.
Restructure the loop so this can't happen. It's simpler this way too. The
unnecessary check for (unsigned)fmt->index < 0 found by Roel Kluin
<roel.kluin@gmail.com> is removed this way too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now urb buffers is not freed before suspend, so uvc_alloc_urb_buffers should
return packet counts allocated originally during uvc resume, instead of zero.
This version uses round down to return packet counts on Linus' suggestions,
or else may lead to buffer destructed if packet size is changed before
calling uvc_alloc_urb_buffers() in this kind of case.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If module initialisation failed (e.g. because the bonding sysfs entry
cannot be created), kernel panics:
IP: [<ffffffff8024910a>] destroy_workqueue+0x2d/0x146
Call Trace:
[<ffffffff808268c4>] bond_destructor+0x28/0x78
[<ffffffff80b64471>] netdev_run_todo+0x231/0x25a
[<ffffffff80b6dbcd>] rtnl_unlock+0x9/0xb
[<ffffffff81567907>] bonding_init+0x83e/0x84a
Remove the calls to bond_work_cancel_all() and destroy_workqueue();
both are also called/scheduled via bond_free_all().
bond_destroy_sysfs is unecessary because the sysfs entry has
not been created in the error case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETH_P_SLOW is already defined in include/linux/if_ether.h.
There's no need to define BOND_ETH_P_LACPDU in drivers/net/bonding/bond_3ad.h
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary length parameter since it's always 4 bytes.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This board doesn't suppot msi-x well due to msi-x table
mapping (hardware) issue.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix the order of irq and hardware context teardown.
Also synchronize the interrupt in dev close() before
releasing tx buffers.
o Fix possible msi-x vector leak if available vectors are
less than requested.
o Request multiple msix vectors only if hardware supports
multiple rx queues.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store msi target status register offset in adapter struct.
This avoids contention on msi_tgt_status table from interrupt
hadlers of different pci function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put generic_show_options read access to s_options under rcu_read_lock,
split save_mount_options() into "we are setting it the first time"
(uses in foo_fill_super()) and "we are relacing and freeing the old one",
synchronize_rcu() before kfree() in the latter.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Divy Le Ray