This patch reduces code redundancy by moving the FACS/S3PT checksum
verification skip logic into acpi_tb_verify_checksum() and other
calls of this function also get benefit from this change. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Paths command displays the full pathname and object type for
the entire namespace. Alternative to the Namespace command.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change removes some dangerous code that attempts to free the
handler context pointer in some (rare) circumstances. The owner of
the handler owns this pointer and the ACPICA code should never
touch it. Although not seen to be an issue in any kernel, it did
show up as a problem under AcpiExec. Also, set the internal storage
field for the context pointer to zero when the region is deactivated,
simply for sanity. David Box.
Signed-off-by: David E. Box <david.e.box@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change adds support to allow hosts to install System Control
Interrupt handlers. Certain ACPI functionality requires the host
to handle raw SCIs. For example, the "SCI Doorbell" that is defined
for memory power state support requires the host device driver to
handle SCIs to examine if the doorbell has been activated. Multiple
SCI handlers can be installed to allow for future expansion.
Debugger support is included.
Lv Zheng, Bob Moore. ACPICA BZ 1032.
Bug summary:
It is reported when the PCC (Platform Communication Channel, via
MPST table, defined in ACPI specification 5.0) subchannel responds
to the host, it issues an SCI and the host must probe the subchannel
for channel status.
Buglink: http://bugs.acpica.org/show_bug.cgi?id=1032
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Perform a sanity check on the start object to prevent problems
later. ACPICA BZ 1025.
This patch only adds additional input parameter validation, no actual
kernel suffering has been discovered.
Buglink: http://bugs.acpica.org/show_bug.cgi?id=1025
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Increase the size of a couple of the debugger line buffers.
ACPICA BZ 1037.
The debugger related code is not in the kernel so the behavior of the
kernel is not affected.
Buglink: http://bugs.acpica.org/show_bug.cgi?id=1037
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow for longer filenames in the module name output during
trace operations.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If an error happens in the middle of a split 32/32 64-bit I/O
operation, do not modify the target of the return value pointer.
Makes the code consistent with the rest of ACPICA. Bjorn Helgaas.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Emit the full offending pathname in the error message.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
1) ACPI-based PCI hotplug (ACPIPHP) fixes related to spurious events
After the recent ACPIPHP changes we've seen some interesting breakage
on a system that triggers device check notifications during boot for
non-existing devices. Although those notifications are really
spurious, we should be able to deal with them nevertheless and that
shouldn't introduce too much overhead. Four commits to make that
work properly.
2) Memory hotplug and hibernation mutual exclusion rework
This was maent to be a cleanup, but it happens to fix a classical
ABBA deadlock between system suspend/hibernation and ACPI memory
hotplug which is possible if they are started roughly at the same
time. Three commits rework memory hotplug so that it doesn't
acquire pm_mutex and make hibernation use device_hotplug_lock
which prevents it from racing with memory hotplug.
3) ACPI Intel LPSS (Low-Power Subsystem) driver crash fix
The ACPI LPSS driver crashes during boot on Apple Macbook Air with
Haswell that has slightly unusual BIOS configuration in which one
of the LPSS device's _CRS method doesn't return all of the information
expected by the driver. Fix from Mika Westerberg, for stable.
4) ACPICA fix related to Store->ArgX operation
AML interpreter fix for obscure breakage that causes AML to be
executed incorrectly on some machines (observed in practice). From
Bob Moore.
5) ACPI core fix for PCI ACPI device objects lookup
There still are cases in which there is more than one ACPI device
object matching a given PCI device and we don't choose the one that
the BIOS expects us to choose, so this makes the lookup take more
criteria into account in those cases.
6) Fix to prevent cpuidle from crashing in some rare cases
If the result of cpuidle_get_driver() is NULL, which can happen on
some systems, cpuidle_driver_ref() will crash trying to use that
pointer and the Daniel Fu's fix prevents that from happening.
7) cpufreq fixes related to CPU hotplug
Stephen Boyd reported a number of concurrency problems with cpufreq
related to CPU hotplug which are addressed by a series of fixes
from Srivatsa S Bhat and Viresh Kumar.
8) cpufreq fix for time conversion in time_in_state attribute
Time conversion carried out by cpufreq when user space attempts to
read /sys/devices/system/cpu/cpu*/cpufreq/stats/time_in_state won't
work correcty if cputime_t doesn't map directly to jiffies. Fix
from Andreas Schwab.
9) Revert of a troublesome cpufreq commit
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) was intended to address some known concurrency problems
in cpufreq related to the ordering of transitions, but unfortunately
it introduced several problems of its own, so I decided to revert it
now and address the original problems later in a more robust way.
10) Intel Haswell CPU models for intel_pstate from Nell Hardcastle.
11) cpufreq fixes related to system suspend/resume
The recent cpufreq changes that made it preserve CPU sysfs attributes
over suspend/resume cycles introduced a possible NULL pointer
dereference that caused it to crash during the second attempt to
suspend. Three commits from Srivatsa S Bhat fix that problem and a
couple of related issues.
12) cpufreq locking fix
cpufreq_policy_restore() should acquire the lock for reading, but
it acquires it for writing. Fix from Lan Tianyu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=U/Jw
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-fixes-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"All of these commits are fixes that have emerged recently and some of
them fix bugs introduced during this merge window.
Specifics:
1) ACPI-based PCI hotplug (ACPIPHP) fixes related to spurious events
After the recent ACPIPHP changes we've seen some interesting
breakage on a system that triggers device check notifications
during boot for non-existing devices. Although those
notifications are really spurious, we should be able to deal with
them nevertheless and that shouldn't introduce too much overhead.
Four commits to make that work properly.
2) Memory hotplug and hibernation mutual exclusion rework
This was maent to be a cleanup, but it happens to fix a classical
ABBA deadlock between system suspend/hibernation and ACPI memory
hotplug which is possible if they are started roughly at the same
time. Three commits rework memory hotplug so that it doesn't
acquire pm_mutex and make hibernation use device_hotplug_lock
which prevents it from racing with memory hotplug.
3) ACPI Intel LPSS (Low-Power Subsystem) driver crash fix
The ACPI LPSS driver crashes during boot on Apple Macbook Air with
Haswell that has slightly unusual BIOS configuration in which one
of the LPSS device's _CRS method doesn't return all of the
information expected by the driver. Fix from Mika Westerberg, for
stable.
4) ACPICA fix related to Store->ArgX operation
AML interpreter fix for obscure breakage that causes AML to be
executed incorrectly on some machines (observed in practice).
From Bob Moore.
5) ACPI core fix for PCI ACPI device objects lookup
There still are cases in which there is more than one ACPI device
object matching a given PCI device and we don't choose the one
that the BIOS expects us to choose, so this makes the lookup take
more criteria into account in those cases.
6) Fix to prevent cpuidle from crashing in some rare cases
If the result of cpuidle_get_driver() is NULL, which can happen on
some systems, cpuidle_driver_ref() will crash trying to use that
pointer and the Daniel Fu's fix prevents that from happening.
7) cpufreq fixes related to CPU hotplug
Stephen Boyd reported a number of concurrency problems with
cpufreq related to CPU hotplug which are addressed by a series of
fixes from Srivatsa S Bhat and Viresh Kumar.
8) cpufreq fix for time conversion in time_in_state attribute
Time conversion carried out by cpufreq when user space attempts to
read /sys/devices/system/cpu/cpu*/cpufreq/stats/time_in_state
won't work correcty if cputime_t doesn't map directly to jiffies.
Fix from Andreas Schwab.
9) Revert of a troublesome cpufreq commit
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) was intended to address some known concurrency
problems in cpufreq related to the ordering of transitions, but
unfortunately it introduced several problems of its own, so I
decided to revert it now and address the original problems later
in a more robust way.
10) Intel Haswell CPU models for intel_pstate from Nell Hardcastle.
11) cpufreq fixes related to system suspend/resume
The recent cpufreq changes that made it preserve CPU sysfs
attributes over suspend/resume cycles introduced a possible NULL
pointer dereference that caused it to crash during the second
attempt to suspend. Three commits from Srivatsa S Bhat fix that
problem and a couple of related issues.
12) cpufreq locking fix
cpufreq_policy_restore() should acquire the lock for reading, but
it acquires it for writing. Fix from Lan Tianyu"
* tag 'pm+acpi-fixes-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
cpufreq: Acquire the lock in cpufreq_policy_restore() for reading
cpufreq: Prevent problems in update_policy_cpu() if last_cpu == new_cpu
cpufreq: Restructure if/else block to avoid unintended behavior
cpufreq: Fix crash in cpufreq-stats during suspend/resume
intel_pstate: Add Haswell CPU models
Revert "cpufreq: make sure frequency transitions are serialized"
cpufreq: Use signed type for 'ret' variable, to store negative error values
cpufreq: Remove temporary fix for race between CPU hotplug and sysfs-writes
cpufreq: Synchronize the cpufreq store_*() routines with CPU hotplug
cpufreq: Invoke __cpufreq_remove_dev_finish() after releasing cpu_hotplug.lock
cpufreq: Split __cpufreq_remove_dev() into two parts
cpufreq: Fix wrong time unit conversion
cpufreq: serialize calls to __cpufreq_governor()
cpufreq: don't allow governor limits to be changed when it is disabled
ACPI / bind: Prefer device objects with _STA to those without it
ACPI / hotplug / PCI: Avoid parent bus rescans on spurious device checks
ACPI / hotplug / PCI: Use _OST to notify firmware about notify status
ACPI / hotplug / PCI: Avoid doing too much for spurious notifies
ACPICA: Fix for a Store->ArgX when ArgX contains a reference to a field.
ACPI / hotplug / PCI: Don't trim devices before scanning the namespace
...
As reported at https://bugzilla.kernel.org/show_bug.cgi?id=60829,
there still are cases in which do_find_child() doesn't choose the
ACPI device object it is "expected" to choose if there are more such
objects matching one PCI device present. This particular problem may
be worked around by making do_find_child() return device obejcts witn
_STA whose result indicates that the device is enabled before device
objects without _STA if there's more than one device object to choose
from.
This change doesn't affect the case in which there's only one
matching ACPI device object per PCI device.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60829
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Felix Lisczyk <felix.lisczyk@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change fixes a problem where a Store operation to an ArgX object
that contained a reference to a field object did not complete the
automatic dereference and then write to the actual field object.
Instead, the object type of the field object was inadvertently changed
to match the type of the source operand. The new behavior will actually
write to the field object (buffer field or field unit), thus matching
the correct ACPI-defined behavior.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull i2c updates from Wolfram Sang:
"Highlights:
- OF and ACPI helpers are now included in the core, and not in
external files anymore. This removes dependency problems for
modules and is cleaner, in general.
- mv64xxx-driver gains fifo usage to support mv78230
- imx-driver overhaul to support VF610
- various cleanups, most notably related to devm_* and CONFIG_PM
usage
- driver bugfixes and smaller feature additions"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: rcar: add rcar-H2 support
i2c: sirf: retry 3 times as sometimes we get random noack and timeout
i2c: sirf: support reverse direction of address
i2c: sirf: fix the typo for setting bitrate to less than 100k
i2c: sirf: we need to wait I2C_RESET status in resume
i2c: sirf: reset i2c controller early after we get a noack
i2c: designware: get SDA hold time, HCNT and LCNT configuration from ACPI
i2c: designware: make HCNT/LCNT values configurable
i2c: mpc: cleanup clock API use
i2c: pnx: fix error return code in i2c_pnx_probe()
i2c: ismt: add error return code in probe()
i2c: mv64xxx: fix typo in binding documentation
i2c: imx: use exact SoC revision to document binding
i2c: move ACPI helpers into the core
i2c: move OF helpers into the core
i2c: mv64xxx: Fix timing issue on Armada XP (errata FE-8471889)
i2c: mv64xxx: Add I2C Transaction Generator support
i2c: powermac: fix return path on error
Documentation: i2c: Fix example in instantiating-devices
i2c: tiny-usb: do not use stack as URB transfer_buffer
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSJo+1AAoJENkgDmzRrbjxIC4QALJK95o8AUXuwUkl+2fmFkUt
hh2/PJ1vDYgk4Xt0J6hyoK7XMa0H1RkbBrROuDdsBnorMFpEsGcgdkUZte9ufoAS
97Bg+7N0KPbTB/S8vOwtW1vbERTJIVPN2uf6h1Wqm9Xc2puCh3HbMMr1AWMGu0WQ
NqY5+Zz8zecy1UOrMhEP6H1CjeQcL1w1DO6YM5ydeqlKNzAz+JMfDXriLPDwiE7+
XFPDF/O3Vtd2ckA7L70Lio7hfHwxV5U4WwFVfiwls98XB4jcZqDKIoh1r8z4SRgR
+0Rae2DN3BaOabGMr//5XdrzQVpwJTh5m2w8BAOHJvCJ9HR7Sq29UIN4u+TowZBy
L2xYo4dvFxkympwu5zEd3c7vHYWKIaqmSq5PIjr4gF/uIo2OeOTrpPIK782ZEYb7
e+qUgOEM05V9AmQZCrSZeP9u474Sj8ow3sCtWxfdRtwNfoEIcUXsNNJd/zDHlVtW
cEtXqc2xXIpcuUJQWlSaGp8fmRQjVZPzrLKYLM2m39ZcOOJbf5rzQAYS7hHPosIa
SK+YVux/+Zzi+Xo/vXq1OlM/SruCr5S7JOgCxLowoQ88vupgXME6uPyC8EO+QQ50
GsrHes5ZNLbk0uVsfcexIyojkUnyvDmmnDpv+1zdC6RgZLJQn8OXp5yNhHhnhrFT
BiHX6YFWtDDqRlVv8Q0F
=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
Pull x86 RAS changes from Ingo Molnar:
"[ The reason for drivers/ updates is that Boris asked for the
drivers/edac/ changes to go via x86/ras in this cycle ]
Main changes:
- AMD CPUs:
. Add ECC event decoding support for new F15h models
. Various erratum fixes
. Fix single-channel on dual-channel-controllers bug.
- Intel CPUs:
. UC uncorrectable memory error parsing fix
. Add support for CMC (Corrected Machine Check) 'FF' (Firmware
First) flag in the APEI HEST
- Various cleanups and fixes"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
amd64_edac: Fix incorrect wraparounds
amd64_edac: Correct erratum 505 range
cpc925_edac: Use proper array termination
x86/mce, acpi/apei: Only disable banks listed in HEST if mce is configured
amd64_edac: Get rid of boot_cpu_data accesses
amd64_edac: Add ECC decoding support for newer F15h models
x86, amd_nb: Clarify F15h, model 30h GART and L3 support
pci_ids: Add PCI device ID functions 3 and 4 for newer F15h models.
x38_edac: Make a local function static
i3200_edac: Make a local function static
x86/mce: Pay no attention to 'F' bit in MCACOD when parsing 'UC' errors
APEI/ERST: Fix error message formatting
amd64_edac: Fix single-channel setups
EDAC: Replace strict_strtol() with kstrtol()
mce: acpi/apei: Soft-offline a page on firmware GHES notification
mce: acpi/apei: Add a boot option to disable ff mode for corrected errors
mce: acpi/apei: Honour Firmware First for MCA banks listed in APEI HEST CMC
generic pstore layer so that all backends can use the
pitiful amounts of storage they control more effectively.
Three other small fixes/cleanups too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=6H8r
-----END PGP SIGNATURE-----
Merge tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull pstore changes from Tony Luck:
"A big part of this is the addition of compression to the generic
pstore layer so that all backends can use the pitiful amounts of
storage they control more effectively. Three other small
fixes/cleanups too.
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore/ram: (really) fix undefined usage of rounddown_pow_of_two
pstore/ram: Read and write to the 'compressed' flag of pstore
efi-pstore: Read and write to the 'compressed' flag of pstore
erst: Read and write to the 'compressed' flag of pstore
powerpc/pseries: Read and write to the 'compressed' flag of pstore
pstore: Add file extension to pstore file if compressed
pstore: Add decompression support to pstore
pstore: Introduce new argument 'compressed' in the read callback
pstore: Add compression support to pstore
pstore/Kconfig: Select ZLIB_DEFLATE and ZLIB_INFLATE when PSTORE is selected
pstore: Add new argument 'compressed' in pstore write callback
powerpc/pseries: Remove (de)compression in nvram with pstore enabled
pstore: d_alloc_name() doesn't return an ERR_PTR
acpi/apei/erst: Add missing iounmap() on error in erst_exec_move_data()
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=CgqW
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
* tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (217 commits)
cpufreq: Don't use smp_processor_id() in preemptible context
cpuidle: coupled: fix race condition between pokes and safe state
cpuidle: coupled: abort idle if pokes are pending
cpuidle: coupled: disable interrupts after entering safe state
ACPI / hotplug: Remove containers synchronously
driver core / ACPI: Avoid device hot remove locking issues
cpufreq: governor: Fix typos in comments
cpufreq: governors: Remove duplicate check of target freq in supported range
cpufreq: Fix timer/workqueue corruption due to double queueing
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
cpufreq: imx6q: Fix clock enable balance
ACPI: blacklist win8 OSI for buggy laptops
cpufreq: tegra: fix the wrong clock name
cpuidle: Change struct menu_device field types
cpuidle: Add a comment warning about possible overflow
cpuidle: Fix variable domains in get_typical_interval()
cpuidle: Fix menu_device->intervals type
cpuidle: CodingStyle: Break up multiple assignments on single line
cpuidle: Check called function parameter in get_typical_interval()
...
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Intel LPSS devices that are enumerated from ACPI have both MMIO and IRQ
resources returned in their _CRS method. However, Apple Macbook Air with
Haswell has LPSS devices enumerated from PCI bus instead and _CRS method
returns only an interrupt number (but the device has _HID set that causes
the scan handler to match it).
The current ACPI / LPSS code sets pdata->dev_desc only when MMIO resource
is found for the device and in case of Macbook Air it is never found. That
leads to a NULL pointer dereference in register_device_clock().
Correct this by always setting the pdata->dev_desc.
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change the ordering of device hotplug locks in scan.c so that
acpi_scan_lock is always acquired after device_hotplug_lock.
This will make it possible to use device_hotplug_lock around some
code paths that acquire acpi_scan_lock safely (most importantly
system suspend and hibernation). Apart from that, acpi_scan_lock
is platform-specific and device_hotplug_lock is general, so the
new ordering appears to be more appropriate from the overall
design viewpoint.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
* acpi-assorted:
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
* pci/misc:
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
This fixes the problem of acpiphp claiming slots that should be managed
by pciehp, which may keep ExpressCard slots from working.
The acpiphp driver claims PCIe slots unless the BIOS has granted us
control of PCIe native hotplug via _OSC. Prior to v3.10, the acpiphp
.add method (add_bridge()) was always called *after* we had requested
native hotplug control with _OSC.
But after 3b63aaa70e ("PCI: acpiphp: Do not use ACPI PCI subdriver
mechanism"), which appeared in v3.10, acpiphp initialization is done
during the bus scan via the pcibios_add_bus() hook, and this happens
*before* we request native hotplug control.
Therefore, acpiphp doesn't know yet whether the BIOS will grant control,
and it claims slots that we should be handling with native hotplug.
This patch requests native hotplug control earlier, so we know whether
the BIOS granted it to us before we initialize acpiphp.
To avoid reintroducing the ASPM issue fixed by b8178f130e ('Revert
"PCI/ACPI: Request _OSC control before scanning PCI root bus"'), we run
_OSC earlier but defer the actual ASPM calls until after the bus scan is
complete.
Tested successfully by myself.
[bhelgaas: changelog, mark for stable]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=60736
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v3.10+
CC: Len Brown <lenb@kernel.org>
CC: "Rafael J. Wysocki" <rjw@sisk.pl>
The current protocol for handling hot remove of containers is very
fragile and causes acpi_eject_store() to acquire acpi_scan_lock
which may deadlock with the removal of the device that it is called
for (the reason is that device sysfs attributes cannot be removed
while their callbacks are being executed and ACPI device objects
are removed under acpi_scan_lock).
The problem is related to the fact that containers are handled by
acpi_bus_device_eject() in a special way, which is to emit an
offline uevent instead of just removing the container. Then, user
space is expected to handle that uevent and use the container's
"eject" attribute to actually remove it. That is fragile, because
user space may fail to complete the ejection (for example, by not
using the container's "eject" attribute at all) leaving the BIOS
kind of in a limbo. Moreover, if the eject event is not signaled
for a container itself, but for its parent device object (or
generally, for an ancestor above it in the ACPI namespace), the
container will be removed straight away without doing that whole
dance.
For this reason, modify acpi_bus_device_eject() to remove containers
synchronously like any other objects (user space will get its uevent
anyway in case it does some other things in response to it) and
remove the eject_pending ACPI device flag that is not used any more.
This way acpi_eject_store() doesn't have a reason to acquire
acpi_scan_lock any more and one possible deadlock scenario goes
away (plus the code is simplified a bit).
Reported-and-tested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
The ECDT of ASUSTEK L4R doesn't provide correct command and data
I/O ports. The DSDT provides the correct information instead.
For this reason, add this machine to quirk list for ECDT validation
and use the EC information from the DSDT.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=60765
Reported-and-tested-by: Daniele Esposti <expo@expobrain.net>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: All <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some machines don't provide _TZD, so check the availability of it
before carrying out futher operations.
If _TZD is present, also check the result of its evaluation.
[rjw: Changelog]
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-bind:
ACPI: Print diagnostic messages if device links cannot be created
ACPI: Drop unnecessary label from acpi_bind_one()
ACPI: Clean up error code path in acpi_unbind_one()
ACPI: Use list_for_each_entry() in acpi_unbind_one()
ACPI: acpi_bind_one()/acpi_unbind_one() whitespace cleanups
ACPI: Create symlinks in acpi_bind_one() under physical_node_lock
ACPI: Reduce acpi_bind_one()/acpi_unbind_one() code duplication
ACPI: Do not fail acpi_bind_one() if device is already bound correctly
* acpica:
ACPICA: Update version to 20130725.
ACPICA: Update names for walk_namespace callbacks to clarify usage.
ACPICA: Return error if DerefOf resolves to a null package element.
ACPICA: Make ACPI Power Management Timer (PM Timer) optional.
ACPICA: Fix divergences of the commit - ACPICA: Expose OSI version.
ACPICA: Fix possible fault for methods that optionally have no return value.
ACPICA: DeRefOf operator: Update to fully resolve FieldUnit and BufferField refs.
ACPICA: Emit all unresolved method externals in a text block
ACPICA: Export acpi_tb_validate_rsdp().
ACPI: Add facility to remove all _OSI strings
ACPI: Add facility to disable all _OSI OS vendor strings
ACPICA: Add acpi_update_interfaces() public interface
ACPICA: Update version to 20130626
ACPICA: Fix compiler warnings for casting issues (only some compilers)
ACPICA: Remove restriction of 256 maximum GPEs in any GPE block
ACPICA: Disassembler: Expand maximum output string length to 64K
ACPICA: TableManager: Export acpi_tb_scan_memory_for_rsdp()
ACPICA: Update comments about behavior when _STA does not exist
* acpi-pm:
ACPI / PM: Add state information to error message in acpi_device_set_power()
ACPI / PM: Remove redundant power manageable check from acpi_bus_set_power()
ACPI / PM: Use ACPI_STATE_D3_COLD instead of ACPI_STATE_D3 everywhere
ACPI / PM: Make messages in acpi_device_set_power() print device names
ACPI / PM: Only set power states of devices that are power manageable
* acpi-pci-hotplug: (34 commits)
ACPI / PM: Hold acpi_scan_lock over system PM transitions
ACPI / hotplug / PCI: Fix NULL pointer dereference in cleanup_bridge()
PCI / ACPI: Use dev_dbg() instead of dev_info() in acpi_pci_set_power_state()
ACPI / hotplug / PCI: Get rid of check_sub_bridges()
ACPI / hotplug / PCI: Clean up bridge_mutex usage
ACPI / hotplug / PCI: Redefine enable_device() and disable_device()
ACPI / hotplug / PCI: Sanitize acpiphp_get_(latch)|(adapter)_status()
ACPI / hotplug / PCI: Get rid of unused constants in acpiphp.h
ACPI / hotplug / PCI: Check for new devices on enabled slots
ACPI / hotplug / PCI: Allow slots without new devices to be rescanned
ACPI / hotplug / PCI: Do not check SLOT_ENABLED in enable_device()
ACPI / hotplug / PCI: Do not exectute _PS0 and _PS3 directly
ACPI / hotplug / PCI: Do not queue up event handling work items in vain
ACPI / hotplug / PCI: Consolidate slot disabling and ejecting
ACPI / hotplug / PCI: Drop redundant checks from check_hotplug_bridge()
ACPI / hotplug / PCI: Rework namespace scanning and trimming routines
ACPI / hotplug / PCI: Store parent in functions and bus in slots
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_bridge
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_func
ACPI / hotplug / PCI: Embed function struct into struct acpiphp_context
...
* acpi-cleanup: (21 commits)
ACPI / dock: fix error return code in dock_add()
ACPI / dock: Drop unnecessary local variable from dock_add()
ACPI / dock / PCI: Drop ACPI dock notifier chain
ACPI / dock: Do not check CONFIG_ACPI_DOCK_MODULE
ACPI / dock: Do not leak memory on falilures to add a dock station
ACPI: Drop ACPI bus notifier call chain
ACPI / dock: Rework the handling of notifications
ACPI / dock: Simplify dock_init_hotplug() and dock_release_hotplug()
ACPI / dock: Walk list in reverse order during removal of devices
ACPI / dock: Rework and simplify find_dock_devices()
ACPI / dock: Drop the hp_lock mutex from struct dock_station
ACPI: simplify acpiphp driver with new helper functions
ACPI: simplify dock driver with new helper functions
ACPI: Export acpi_(bay)|(dock)_match() from scan.c
ACPI: introduce two helper functions for _EJ0 and _LCK
ACPI: introduce helper function acpi_execute_simple_method()
ACPI: introduce helper function acpi_has_method()
ACPI / dock: simplify dock_create_acpi_device()
ACPI / dock: mark initialization functions with __init
ACPI / dock: drop redundant spin lock in dock station object
...
Since v3.7 the acpi backlight driver doesn't work correctly in several
machines because ACPI code has different code for Windows 8, and the
rest.
The commit ea45ea7 (in v3.11-rc2) tried to fix this problem by using the
intel backlight driver, however it introduced several other issues in
different machines.
This patch fixes both regressions by blacklisting the win8 OSI, so we
are back to v3.6 behavior, and it should remain that way until the intel
backlight driver is fixed.
Since v3.7, users have been forced to fix the initial regression by
modifying the boot arguments (acpi_osi="!Windows 2012").
Once the Intel backlight driver works correctly for all machines, this
blacklist can be removed and that driver can be used instead.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60682
Reported-by: Danny Baumann <dannybaumann@web.de>
Reported-by: Philipp Richter <richterphilipp.pops@gmail.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This follows what has already been done for the DeviceTree helpers. Move
the ACPI helpers from drivers/acpi/acpi_i2c.c to the I2C core and update
documentation accordingly.
This also solves a problem reported by Jerry Snitselaar that we can't build
the ACPI I2C helpers as a module.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Revert commit c04c697 (ACPI / video: Always call acpi_video_init_brightness()
on init), because it breaks eDP backlight at 1920x1080 on Acer Aspire S3
for Trevor Bortins.
References: https://bugs.freedesktop.org/show_bug.cgi?id=68355
Reported-and-bisected-by: Trevor Bortins <enabfluw@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No need to call sysfs_bin_attr_init, as the attribute is not dynamically
created. Also, we renamed the attribute, so this one isn't even valid
anymore.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attribute groups now can handle binary sysfs attributes, so clean up the
code here by using a binary attribute array. This saves us the extra
call to create the binary attribute at saves 6 lines overall.
Cc: Len Brown <lenb@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
I can take this in my driver-core tree if someone from ACPI acks it,
otherwise, feel free to take it through the ACPI trees instead, just
let me know.
drivers/acpi/bgrt.c | 26 ++++++++++----------------
1 file changed, 10 insertions(+), 16 deletions(-)
Bad things happen if ACPI hotplug events are handled during system
PM transitions, especially if devices are removed as a result.
To prevent those bad things from happening, acquire acpi_scan_lock
when a PM transition is started and release it when that transition
is complete or has been aborted.
This fixes resume lockup on my test-bed Acer Aspire S5 that happens
when Thunderbolt devices are disconnected from the machine while
suspended.
Also fixes the analogous problem for Mika Westerberg on an
Intel DZ77RE-75K board.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
In pstore write, set the section type to CPER_SECTION_TYPE_DMESG_COMPR
if the data is compressed. In pstore read, read the section type and
update the 'compressed' flag accordingly.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Backends will set the flag 'compressed' after reading the log from
persistent store to indicate the data being returned to pstore is
compressed or not.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Addition of new argument 'compressed' in the write call back will
help the backend to know if the data passed from pstore is compressed
or not (In case where compression fails.). If compressed, the backend
can add a tag indicating the data is compressed while writing to
persistent store.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Lv Zheng