'n' may be bigger than MAX_INT*sizeof(int), if so checking of truncated
(int)(n/sizeof(int)) for LIRCBUF_SIZE overflow and then using nontruncated 'count'
doesn't make sense. Also n may be up to sizeof(int)-1 bytes bigger than expected,
so check value of (n % sizeof(int)) too.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This module implements V4L2 controls for the Texas Instruments
WL1273 FM Radio and handles the communication with the chip.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for cameras with the HV7131D sensor, such as the 0c45:602a
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our old start of frame detection code wrongly assumes that the sof
marker always lives at the beginning of the frame. At least for the
0c45:602a camera this is not the case. This patch also improves
the framerate from 28 fps to 30 fps with the 0c45:6005 and 0c45:6007
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've a 0c45:6007 camera and it works fine with the gspca_sonixb driver,
so make that handle it instead of the deprecated sn9c102 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At Pixelview SBTVD Hybrid, the bits sent by the IR are inverted. Due to that,
the existing keytables produce wrong codes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the following error in PowerPC builds:
drivers/media/video/timblogiw.c: In function 'timblogiw_probe':
drivers/media/video/timblogiw.c:749: error: timblogiw_ioctl_ops causes a section type conflict
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for mt9m001 (mi1300) is broken:
- Table is incomplete;
- Only one resolution is currently supported by the driver;
- Resolution is incomplete;
- it complains about broken JPEG headers.
Use the same init found on em28xx driver, and properly report the
output format as 8-bits GRAY.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 35680ba broke several devices:
- Sony Playstation Eye (1415:2000);
- Gigaware model 25-234 (0c45:628f);
- Logitech Messenger Plus (046d:08f6).
Probably more devices were broken by this change.
What happens is that several devices don't need to save some bandwidth
for audio.
Also, as pointed by Hans de Goede <hdegoede@redhat.com>, the logic
that implements the bandwidth reservation for audio is broken, since
it will reduce the alt number twice, on devices with audio.
So, let's just revert the broken logic, and think on a better solution
for usb 1.1 devices with audio that can't use the maximum packetsize.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use macros for the supported scales, instead of using magic numbers
from 0 to 3.
Code become cleaner by using macros for it.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of just assuming a ov9650 sensor based on USB ID,
double-check it, by reading the sensor ID.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add kycodes for DSR-0112 remote that comes together with
Haupauge MiniStick
http://lirc.sourceforge.net/remotes/hauppauge/DSR-0112.jpg
[mchehab@redhat.com: Fix KEY_PREVIOUS to match the definition for the other model]
Signed-off-by: Richard Zidlicky <rz@linux-m68k.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I found that the problems people have reported with the USB-TV-stick
"Terratec Cinergy Hybrid T USB XS" (USB-ID: 0ccd:0042)
are coming from a wrong header file in the v4l-sources.
Attached is a diff, which fixes the problem (tested successfully here).
Obviously the USB-ID has been associated with a wrong chip: EM2880
instead of EM2882, which would be correct.
Reported-by: Philippe Bourdin <richel@AngieBecker.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kobject_set_name() may fail with -ENOMEM, check for it.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a loopback driver to rc-core which I've found useful for
running scripted tests of different parts of rc-core without having to
fiddle with real hardware.
Basically it emulates hardware with a learning and a non-learning
receiver and two transmitters (which correspond to the two
receivers). TX data that is sent is fed back as input on the
corresponding receiver, which allows for debugging of IR decoders,
keymaps, etc.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At ir_setkeycode, if INPUT_KEYMAP_BY_INDEX is used, the routine may return
an invalid value if not error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RC5 old decoder used custom_irq to indicate the need of handling
the IRQ on a different way. Instead of doing it, let the core just call the
bttv input IRQ handler, and add the code there to call the legacy decoder.
While here, remove the gpioq waitqueue, as this is not used anywhere, and
add a debug msg to help removing the legacy RC5 code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lock isn't held here and doesn't need to be unlocked. The code has
been like this since the driver was merged.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more
difficult to make use of the devices in userspace as their names can
change.
Forward-ported to media_tree staging/for_v2.6.38 and tested with
both streamzap and mceusb devices:
$ ll /dev/input/by-id/
...
lrwxrwxrwx. 1 root root 9 Nov 17 17:06 usb-Streamzap__Inc._Streamzap_Remote_Control-event-if00 -> ../event6
lrwxrwxrwx. 1 root root 9 Nov 17 17:05 usb-Topseed_Technology_Corp._eHome_Infrared_Transceiver_TS000BzY-event-if00 -> ../event5
Previously, nada.
Signed-off-by: Paul Bender <pebender@gmail.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure we have a matching chip id high and one or the other
of the chip id low values.
Print the values if the probe fails.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've got code which adds support of GoTView PCI DVD3 Hybrid tuner in
cx18 module and Andy Walls in ivtv mailing-list gave me some advice on
making a patch and sending it here. So here's the patch against
staging/2.6.37-rc1 branch (the tutorial recommends to include it as
plain text but if it's the case I can surely send as an attachment):
Several comments on the patch:
1. Both users on the official Gotview forum and support said that PCI
DVD3 is very similar to Yuan MPC718 card so the main part of code is
taken from Yuan configuration. Some users reported it to work properly.
2. Everything is being initialized correctly including analog, dvb,
radio and alsa parts. Analogue part and alsa virtual card is tested by
myself using original Gotview card.
[mchehab@redhat.com: Whitespace cleanups]
Signed-off-by: Alexey Chernov <4ernov@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that a wrong cut-and-paste error were done here.
Reported-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch fixes the rc-tbs-nec table after converting
drivers/media/video/cx88 to ir-core
(commit ba7e90c9f878e0ac3c0614a5446fe5c62ccc33ec).
It is also adds two missing buttons (10- and 10+) with
its definition (KEY_10CHANNELSUP and KEY_10CHANNELSDOWN).
[mchehab@redhat.com: move keycode numbers to 0x1b8/0x1b9 as requested by the input Maintainer]
Signed-off-by: Mariusz Białończyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some minor comments etc which are leftover from the old naming scheme.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Similarly to saa7134, bttv_ir has two timers, only one of which is used
at a time and which serve the same purpose. Merge them.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
bttv_ir is more consistent with all other structs used in the same driver.
Also, clean up the struct to remove commented out members and the work_struct
which is unused.
[mchehab@redhat.com: fix a warning at bttv_rc5_timer_end]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both timers are used for a similar purpose. Merging them allows for some
minor simplifications.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mostly using appropriate data types and constants (e.g. int -> bool).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using the full keycode for BeholdTV hardware makes another module
parameter unnecessary.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir_rc5_remote_gap is a leftover from ir-common, remove it.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Failure to submit an urb is a fatal error, make isoc_init return an
error when this happens rather then only log it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
isoc_cleanup contains a check to not set the altsetting to alt0 when
the device was unplugged, but the check currently is buggy, and causes
the alt setting to only be set to 0 if an error occured while streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pwc was starting streaming on /dev/video# open rather then on STREAM_ON. Now
that the v4l1 compat code is removed from the pwc driver there is no reason
left to do this. So this patch changes the pwc driver to delay starting
the isoc stream (and thus using valuable usb bandwidth) until the application
does a STREAM_ON
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/stb6100.c:120: warning: ‘stb6100_normalise_regs’ defined but not used
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote keytables had different names all over the place. Part of the fault
is due to a bad naming when rc subsystem was created, but there were lots
of old names that were still here.
Use a common standard for everything.
Patch generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_codes_,rc_map_,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_key_map,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_map_table_size,rc_map_size,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The struct that describes a rc mapping had an weird and long name.
We should properly name it, to make easier for developers to work
with it, and to avoid confusion.
Basically, generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode_table,rc_map,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_tab,rc_map,g <$i >a && mv a $i; done
(and manually fixed where needed)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc_map is confusing, as it may be understood as another thing. Properly
rename the field to indicate its usage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h
To be consistent with the other changes.
No functional change on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Something weird happened with commit 740069e6e043403199dbe2b42256722fb814f6ae.
Instead of dong the right thing, it got somehow corrupted and reverted the
rc changes.
Thanks to David Härdeman for pointing me about the problem.
This patch should be merged with 740069e6e04 before sending upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Some badly written applications in conjuction with certain SEC devices
do send too many messages causing the DiSEqC bus to get congested. As
a result, the end devices do get confused and hence do not respond.
The issue was found by Julian Scheel.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Reduce the amount of white noise present, which causes the
demodulator a significant time to acquire a frontend lock
on a whole. Frontend shows a large significant improvement in
performance.
Thanks to Peter Nayler for helping to identify the potential
hotspots and fixing them.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is declared extern and exported, and should not be given
a generic name which may conflict with gpiolib in future.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the driver to use the dvb_attach macro to avoid the hard dependency
on the frontend drivers. The hard dependecy will result in loading a
number of unused frontends, and unwanted automatic dereferencing.
This fixes a bug where unloading the mantis driver will derefence any
attached frontend twice, which will cause an oops if the same frontend is
used by another driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After dvb-core has called mantis-fe->stop_feed(dvbdmxfeed)
the last time (count to zero), no data should ever be copied
with dvb_dmx_swfilter() by a tasklet: the target structure
might be in an unusable state. Caller of mantis_fe->stop_feed()
assumes that feeding is stopped after stop_feed() has been
called, ie. dvb_dmx_swfilter() isn't running, and won't be called.
There is a risk that dvb_dmx_swfilter() references freed resources
(memory or spinlocks or ???) causing instabilities. Thus
tasklet_disable(&mantis->tasklet) must be called inside of
mantis-fe->stop_feed(dvbdmxfeed) when necessary.
Signed-off-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
use the macro to make modules auto-loadable
Thanks to Ozan Çağlayan <ozan@pardus.org.tr> for pointing it out
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c-core does this already.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
The [vk][cmz]alloc(_node) family of functions return void pointers which
it's completely unnecessary/pointless to cast to other pointer types since
that happens implicitly.
This patch removes such casts from drivers/media/
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
timblogiw uses dma() interfaces and it selects TIMB_DMA for that
support. However, drivers/dma/ is not built unless
CONFIG_DMA_ENGINE is enabled, so select/enable that symbol also.
drivers/built-in.o: In function `timblogiw_close':
timblogiw.c:(.text+0x4419fe): undefined reference to `dma_release_channel'
drivers/built-in.o: In function `buffer_release':
timblogiw.c:(.text+0x441a8d): undefined reference to `dma_sync_wait'
drivers/built-in.o: In function `timblogiw_open':
timblogiw.c:(.text+0x44212b): undefined reference to `__dma_request_channel'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the timberdale video-in driver.
The video IP of timberdale delivers the video data via DMA.
The driver uses the DMA api to handle DMA transfers, and make use
of the V4L2 video buffers to handle buffers against user space.
If available the driver uses an encoder to get/set the video standard
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that ix2505v driver ignores a i2c error in ix2505v_read_status_reg.
This looks like a typing error using (ret = 1) instead of correct (ret == 1).
Acked-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, just one old bttv board uses the old RC5 raw decoding routines.
Its conversion to rc-core requires the generation of IRQ data for both
positive and negative transitions at the IRQ line. I'm not sure if
bttv driver supports it or if the transitions will be reliable enough.
So, due to the lack of hardware for testing, the better for now is to
just move the legacy routines to bttv driver, and wait for someone with
a Nebula Digi could help to port it to use also rc-core raw decoders.
Acked-by: Hermann Pitton <hermann-pitton@arcor.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only IR left still using the old raw decoders on saa7134 is ENCORE
FM 5.3. As it is now using the standard rc-core raw decoders, lots
of old code can be removed from saa7134.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- start and stop streaming are done via the FRAR
- streaming suspend (for control change) is done by video reset
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It looks to me like it was intended to check the return value
at this point.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also checks if the sensor is well detected at connection time.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv06xx devices have only one altsetting, but the actual used
bandwidth can be programmed through a register. We were already
setting this register lower then the max packetsize of the altsetting
indicates. This patch makes the gspca-stv06xx update the usb descriptor
for the alt setting to reflect the actual packetsize in use, so that
the usb subsystem uses the correct information for scheduling usb transfers.
This patch also tries to fallback to lower speeds in case a ENOSPC error
is received when submitting urbs, but currently this is only supported
with stv06xx cams with the pb0100 sensor, as this is the only one for
which we know how to change the framerate.
This patch is based on an initial incomplete patch by
Lee Jones <lee.jones@canonical.com>
Signed-off-by: Lee Jones <lee.jones@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Checkpatch compliance cleanup across files in the saa7164 driver.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This isn't a runtime bug, it's just to make static checkers happy.
In vidioc_querycap() we copy a saa7164_dev ->name driver array into a
v4l2_capability -> driver array. The ->driver array is only 16 chars
long so ->name also can't be more than 16 characters.
The ->name gets set in v4l2_capability() and it always is less than 16
characters so we can easily make the buffer smaller.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the adapter does not support I2C_FUNC_SMBUS_WRITE_BYTE,
return -EIO instead of 0.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds retrieval of firmware and FPGA versions of Genpix devices.
That information is useful for users who experience performance differences
with the various firmware versions, and may want to use a specific firmware
that best suits their needs.
Example dmesg output:
gp8psk: FW Version = 2.09.4 (0x20904) Build 2009/04/02
gp8psk: FPGA Version = 1
Signed-off-by: Derek Kelly <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a bug at cx231xx-input, where it were registering the remote
controls twice, one via ir-kbd-i2c and another directly.
Also, the patch that added rc_register_device() broke compilation for it.
This patch fixes cx231xx-input by fixing the depends on, to point to the
new symbol, and initializing the scanmask via platform_data.
While here, also fix Kconfig symbol change for IR core dependencies.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several fields on rc_dev that drivers can benefit. Allow drivers
to pass it as a parameter to the driver.
For now, the rc_dev parameter is optional. If drivers don't pass it, create
them internally. However, the best is to create rc_dev inside the drivers,
in order to fill other fields, like open(), close(), driver_name, etc.
So, a latter patch making it mandatory and changing the caller drivers is
welcome.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move winbond-cir from drivers/input/misc/ into drivers/media/rc/
and convert it to use rc-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.
This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.
The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()
[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: this patch were originally bundled with some renaming
stuff and with the file merges, as seen at:
https://patchwork.kernel.org/patch/291092/.
Instead of using the original approach, I wrote the rename patches and the
code merge as separate changes, then applied the difference on this patch.
This way, it is easier to see the real changes at the code, and will be easier
to merge upstream, especially if some conflict rises on the renaming patches]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this change, all rc-core functions are into just one file, except
for the rc-raw specific functions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88 only depends on VIDEO_IR because it needs ir_extract_bits().
Move that function to ir-core.h and make it inline.
Lots of drivers had dependencies on VIDEO_IR when they really
wanted IR_CORE.
The only remaining drivers to depend on VIDEO_IR are bt8xx and
saa7134 (ir_rc5_timer_end is the only function exported by
ir-functions).
Rename VIDEO_IR -> IR_LEGACY to give a hint to anyone writing or
converting drivers to IR_CORE that they do not want a dependency
on IR_LEGACY.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the remaining usages of the ir_input_nokey() and
ir_input_keydown() functions provided by drivers/media/IR/ir-functions.c
by using the corresponding functionality in ir-core instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the cx88 driver (for sampling hw) to use the
decoders provided by ir-core instead of the separate ones provided
by ir-functions (and gets rid of those).
The value for MO_DDS_IO had a comment saying it corresponded to
a 4kHz samplerate. That comment was unfortunately misleading. The
actual samplerate was something like 3250Hz.
The current value has been derived by analyzing the elapsed time
between interrupts for different values (knowing that each interrupt
corresponds to 32 samples).
Thanks to Mariusz Bialonczyk <manio@skyboo.net> for testing my patches
(about one a day for two weeks!) on actual hardware.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the driver to use regulator framework instead of set_power callback.
This with gpio_reset platform data provide cleaner way to manage chip VIO,
VDD and reset signal inside the driver.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Because some clients (e.g. tvtime) will just open the filehandle and call
read() instead of explicitly calling streamon first, we need to make sure the
VBI timeout routine gets enabled in this case.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first pass of fixes to cause the driver to continue streaming even when
there is no video arriving over the ITU656 bus were not adequate. Continue
the work from the previous patch.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need the au0828 to continue delivering frames even when the device is not
delivering video, or else applications such as tvtime will block indefinitely.
Unfortunately, the au8522 doesn't have any sort of free-running mode or "blue
screen on no video" like some other decoders.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tweak the comb filter config when in s-video mode to match the Hauppauge
Windows driver values (based on register dumps).
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Straighten out the clamp control configurations for the various video modes,
based off of register diffs done against the Hauppauge Windows driver.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup the routine which disables the audio decoder. In particular, the i2s
output was being shut off but the audio processor itself was not, resulting
in more power being consumed than needed.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the alignment of fields being delivered by the driver, which was
resulting in jerky video when there was horizontal motion (since the bottom
field of the frame was being sent with the top field of the previous frame)
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We had the max packets per URB set to an incredibly low "10" as opposed to
the Windows driver which has it as 128. Set the value to match the
Windows driver, which will reduce interrupts considerably.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The chip's default value for the brightness didn't match what we were sending
back in the queryctrl ioctl(), so if the application actually set the
brightness to the "default", it would actually end up being way too bright.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bad value prevented the autogain to work correctly
and some images were truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Generate a release button event when the button is still pressed when the
stream stops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_xirlink_cit: Add support camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least on the ibm netcam pro frames have a 4 byte footer, take this
into account when calculating sizeimage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following usb bandwidth allocation changes were made to the ibm netcam
pro code:
- Don't restart negotiation at max packet size on stop0, as that gets called
by gspca_main during negotiation. Move this to sd_isoc_init.
- Don't ask for full bandwidth when running at 160x120, that does not need
full bandwidth
- Make minimum acceptable bandwidth depend upon resolution
[mchehab@redhat.com: Fix CodingStyle problems at switch statements]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently alloc_and_submit_int_urb() is setting gspca->int_urb
as soon as the allocation has succeeded, but if the subsequent
submit fails, the urb gets destroyed. And then later will
get destroyed again in gspca_input_destroy_urb() because
gspca->int_urb is set, leading to a double free.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently gspca supported usb-1.1 webcams for which we support the input
button through an interrupt endpoint won't stream (not enough bandwidth
error) when used through an USB-2.0 hub.
After much debugging I've found out that the cause for this is that the
ehci-sched.c schedeling code does not like it when there are already urb's
scheduled when (large) isoc urbs are queued. By moving the submission
of the interrupt urbs to after submitting the isoc urbs the camera
starts working again through usb-2.0 hubs.
Note that this does not fix isoc. streaming through a usb-hub while another
1.1 usb device (like the microphone of the same cam) is also active
at the same time :(
I've spend a long time analyzing the linux kernel ehci scheduler code,
resulting in this (long) mail:
http://www.spinics.net/lists/linux-usb/msg37982.html
The conclusion of the following mail thread is that yes there are several
issues when using usb-1.1 devices through a usb-2.0 hub, but these are not
easily fixable in the current code. Fixing this in ehci-sched.c requires
an almost full rewrite, which is not bound to happen anytime soon.
So with this patch gspca driven usb-1.1 webcams will atleast work when
connected through an usb-2.0 hub when the microphone is not used.
As an added bonus this patch avoids extra destroy/create input urb cycles
when we end up falling back to a lower speed alt setting because of bandwidth
limitations.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DM04/QQBOX USB Timing change.
Improved timing to avoid USB corruptions on some systems.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improved frontend handling.
Frontend now remains open at all times, with signal lock, snr & signal level
polled from Interupt.
Updated driver for DM04/QQBOX USB DVB-S BOXES to version 1.70.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you suspend and resume during video capture, the video colours
are corrupted on resume. This is because the sensor is being unconditionally
powered off during the resume path.
Only power down during resume if the camera is not in use, and correctly
reconfigure the sensor during resume.
Fixes http://dev.laptop.org/ticket/10190
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although cx231xx has a very good IR support, already supported by
mceusb driver, some designs decided to add a separate I2C
microcontroller chip in order to handle IR.
Due to that, add a glue to ir-kbd-i2c is needed, in order to support
those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By comparing the traffic between Pixelview (cx23102-based and Kworld
(saa7134-based), the only difference is at register 0xd5. After some
tests, It seems that it is used to change mode between serial and parallel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the trivial bits to mb86a20s. As the driver won't touch
at the channel/layer parameters, this may not be enough for
receiving all channels, especially ISDB-Tsb, but the driver worked
properly for receiving video channels on my tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses an em2874B + Sharp 921 One Seg frontend.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On our tests with Leadership ISDBT, the s921 frontend were not work. As its
design contained some weird things, it ended to be easier to just re-write
it, getting another frontend as an example (cx24123).
As the old s921 driver weren't used, there's no regression. Some info from
the old frontend were used as a way to double check the behavior that were
noticed on the USB dumps retrieved from Leadership driver.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a partial revert of b595076a18
("tree-wide: fix comment/printk typos"), as it changes the code
that no longer exists in linux-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A recent patch has introduced a regression, whereby a second open of an
soc-camera video device breaks the running capture. This patch fixes this bug
by guaranteeing, that video buffers get initialised only during the first open
of the device node.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the remaining users of flush_scheduled_work() in
media/video.
* bttv-input.c and cx23885-input.c don't use workqueue at all. No
need to flush.
* Make omap24xxcam.c and saa7134-empress.c flush the used work
directly.
* In fd_defio.c, replace cancel_delayed_work() +
flush_scheduled_work() with cancel_delayed_work_sync(). While at
it, replace the deprecated cancel_rearming_delayed_work() with
cancel_delayed_work_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Video drivers request submodules using a work during probe and calls
flush_scheduled_work() on exit to make sure the work is complete
before being unloaded. This patch makes these drivers flush the work
directly instead of using flush_scheduled_work().
While at it, relocate request_submodules() call in saa7134_initdev()
right right before successful return as in other drivers to avoid
failing after the work is scheduled and returning failure without the
work still active.
This is in preparation for the deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
flush_scheduled_work() is deprecated and scheduled to be removed.
* Flush the used works directly.
* Replace the deprecated cancel_rearming_delayed_work() +
flush_scheduled_work() -> cancel_delayed_work_sync().
* Make sure mantis->uart_work isn't running on exit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (21 commits)
[media] mceusb: set a default rx timeout
[media] mceusb: fix inverted mask inversion logic
[media] mceusb: add another Fintek device ID
[media] lirc_dev: fixes in lirc_dev_fop_read()
[media] lirc_dev: stray unlock in lirc_dev_fop_poll()
[media] rc: fix sysfs entry for mceusb and streamzap
[media] streamzap: merge timeout space with trailing space
[media] mceusb: fix keybouce issue after parser simplification
[media] IR: add tv power scancode to rc6 mce keymap
[media] mceusb: buffer parsing fixups for 1st-gen device
[media] mceusb: fix up reporting of trailing space
[media] nuvoton-cir: improve buffer parsing responsiveness
[media] mceusb: add support for Conexant Hybrid TV RDU253S
[media] s5p-fimc: Fix output DMA handling in S5PV310 IP revisions
[media] s5p-fimc: Use correct fourcc code for 32-bit RGB format
[media] s5p-fimc: Convert m2m driver to unlocked_ioctl
[media] s5p-fimc: Explicitly add required header file
[media] s5p-fimc: Fix vidioc_g_crop/cropcap on camera sensor
[media] s5p-fimc: BKL lock removal - compilation fix
[media] soc-camera: fix static build of the sh_mobile_csi2.c driver
...
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Its possible for the call to read rx timeout from the hardware to fail,
in which case we end up with a bogus rx timeout value. Set a default one
when filling in the rc struct, and we'll just overwrite it later w/the
value from hardware, but if that read fails, we've at least got a sane
rx timeout value to work with (1000ms is the default value I've seen
returned on most if not all mceusb hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As it turns out, somewhere along the way, we managed to invert the
meaning of the tx_mask_inverted flag. Looking back over the old lirc
driver, tx_mask_inverted was set to 0 if the device was in tx_mask_list.
Now we have a tx_mask_inverted flag set to 1 for all the devices that
were in the list, and set tx_mask_inverted to that flag value, which is
actually the opposite of what we used to set, causing set_tx_mask to use
the wrong mask setting option. Since there seem to be more devices with
inverted masks than not (using the original device as the baseline for
inverted vs. normal), lets just call the ones currently marked as
inverted normal instead, and flip the if/else actions that key off of
the inverted flag.
Note: the problem only cropped up if a call to set_tx_mask was made, if
no mask was set, the device would work just fine, which is why this
managed to slip though w/o getting noticed until now.
Tested successfully by myself and Dennis Gilmore.
Reported-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes several changes but they're in one function and sort of
related:
"buf" was leaked on error. The leak if we try to read an invalid
length is the main concern because it could be triggered over and
over.
If the copy_to_user() failed, then the original code returned the
number of bytes remaining. read() is supposed to be the opposite way,
where we return the number of bytes copied. I changed it to just return
-EFAULT on errors.
Also I changed the debug output from "-EFAULT" to just "<fail>" because
it isn't -EFAULT necessarily. And since we go though that path if the
length is invalid now, there was another debug print that I removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We shouldn't unlock here. I think this was a cut and paste error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more
difficult to make use of the devices in userspace as their names can
change.
Signed-off-by: Paul Bender <pebender@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are cases where we get an ending space, and our trailing timeout
space then gets sent right after it, which breaks repeat, at least for
lirc userspace decoding. Merge the two spaces by way of using
ir_raw_event_store_filter, set a timeout value, and we're back to good.
Successfully tested with streamzap and windows mce remotes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Something I failed to notice while testing the mceusb RLE buffer
decoding simplification patches was that we were getting an extra event
from the previously pressed key.
As was pointed out to me on irc by Maxim, this is actually due to using
ir_raw_event_store_with_filter without having set up a timeout value.
The hardware has a timeout value we're now reading and storing, which
properly enables the transition to idle in the raw event storage
process, and makes IR decode behave correctly w/o keybounce.
Also remove no-longer-used ir_raw_event struct from mceusb_dev struct
and add as-yet-unused enable flags for carrier reports and learning
mode, which I'll hopefully start wiring up sooner than later. While
looking into that, found evidence that 0x9f 0x15 responses are only
non-zero when the short-range learning sensor is used, so correct the
debug spew message, and then suppress it when using the standard
long-range sensor.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.
Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than waiting for trigger bits, the formula for which was slightly
messy, and apparently, not actually 100% complete for some remotes, just
call ir_raw_event_handle whenever we finish parsing a chunk of data from
the rx fifo, similar to mceusb, as well as whenever we see an 'end of
signal data' 0x80 packet.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial values of the registers 0x01 and 0x17 are taken from the sensor
table at capture start and updated according to the flag PDN_INV.
Their values are updated at each step of the capture initialization and
memorized for reuse in capture stop.
This patch also fixed automatically some bad hardcoded values of these
registers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The flag PDN_INV indicates that the sensor pin S_PWR_DN has not the same
value as other webcams with the same sensor. For now, only two webcams have
been so detected: the Microsoft's VX1000 and VX3000.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After Mauro's "bttv: Fix locking issues due to BKL removal code" there
are a number of comments that are no longer needed about lock ordering.
Remove them.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression where bttv driver causes oopses when loading, since it
were using some non-initialized mutexes. While it would be possible to
fix the issue, there are some other lock troubles, like to the presence of
lock code at free_btres_lock().
It is possible to fix, but the better is to just use the core-assisted
locking schema. This way, V4L2 core will serialize access to all
ioctl's/open/close/mmap/read/poll operations, avoiding to have two
processes accessing the hardware at the same time. Also, as there's just
one lock, instead of 3, there's no risk of dead locks.
The net result is a cleaner code, with just one lock.
Reported-by: Dan Carpenter <error27@gmail.com>
Reported-by: Brandon Philips<brandon@ifup.org>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Really fix build break on symbol-prefixed archs
[media] Fix Kconfig errors due to two visible menus
i2c/algos: convert Kconfig to use the menu's `visible' keyword
media/video: convert Kconfig to use the menu's `visible' keyword
Revert "i2c: Fix Kconfig dependencies"
kconfig: regen parser
kconfig: add an option to determine a menu's visibility
Drivers should append their name on exported symbols, to avoid
conflicts with allyesconfig:
drivers/staging/built-in.o: In function `format_by_fourcc':
/home/v4l/work_trees/linus/drivers/staging/cx25821/cx25821-video.c:96: multiple definition of `format_by_fourcc'
drivers/media/built-in.o:/home/v4l/work_trees/linus/drivers/media/common/saa7146_video.c:88: first defined here
Let's rename both occurences with a small shellscript:
for i in drivers/staging/cx25821/*.[ch]; do sed s,format_by_fourcc,cx25821_format_by_fourcc,g <$i >a && mv a $i; done
for i in drivers/media/common/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
for i in include/media/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvcvideo driver now locks all ioctls correctly on its own, the BKL
isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The stream mutex protects access to the struct uvc_streaming ctrl,
cur_format and cur_frame fields as well as to the hardware probe
control. Lock it appropriately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mmap() implementation belongs to the video buffers queue, move it
there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callers outside uvc_queue.c should not be forced to lock/unlock the
queue mutex manually. Move the mutex operations inside
uvc_free_buffers().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
uvc_find_control() must be called with the controls mutex locked. Fix
uvc_query_v4l2_menu() accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The unregister function had a race condition with the v4l2_open
function. Ensure that both functions test and clear the REGISTER
flag from within a critical section.
Thanks to Laurent Pinchart for finding this race.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL replacement mutex had some serious performance side-effects on
V4L drivers. It is replaced by a better heuristic that works around the
worst of the side-effects.
Read the v4l2-dev.c comments for the whole sorry story. This is a
temporary measure only until we can convert all v4l drivers to use
unlocked_ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Where reasonable use mutex_lock_interruptible instead of mutex_lock.
Also fix the poll, read and write error codes when called with an unregistered
device (e.g. after a USB device was disconnected). Poll must return
POLLERR|POLLHUP and read/write must return -ENODEV.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also added locking around snd_cx18_pcm_ioctl as a precaution
as requested by Andy Walls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial conversion, this driver used a mutex already.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These drivers could be trivially converted to unlocked_ioctl since they
already did locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the typhoon driver from ioctl to unlocked_ioctl.
When doing this I noticed a bug where curfreq was not initialized correctly
to mutefreq (it wasn't multiplied by 16).
The initialization is now also done before the device node is created.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert ioctl to unlocked_ioctl. Note that for this driver the locking
is done inside the sub-device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert from ioctl to unlocked_ioctl using the v4l2 core lock.
Also removed the 'exclusive access' limitation. There was no need for it
and it violates the v4l2 spec as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted from ioctl to unlocked_ioctl.
This driver already used an internal lock, but it was missing in cadet_open and
cadet_release and it was not used correctly in cadet_read.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch converts a bunch of V4L2 radio drivers to unlocked_ioctl.
These are all simple conversions: most already had a lock and so the ioctl
fop could simply be replaced by unlocked_ioctl.
radio-miropcm20.c was converted to use the new V4L2 core lock.
While doing this work I noticed that many of these drivers initialized
some more fields or muted audio or something like that *after* creating
the device node. This should be done before the device node is created
to prevent problems. Especially hal tends to grab a device node as soon
as it is created.
In one or two cases the mutex_init was even done after the device creation!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The argument isn't used anymore by the functions, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL in the cafe-ccic, via-camera and s5p-fimc drivers.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the new visible Kconfig keyword to avoid producing error for two menus
that are visible only if Tuner/frontend customise options are enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch (as1436) takes care of leftover references to
udev->autosuspend_delay that didn't get removed during the earlier
conversion to the runtime-PM autosuspend API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
mx2-camera got broken during the last merge window. This patch
fixes this and removes some unused variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a followup patch that addresses two minor issues left in the recently
added ov6650 sensor driver, as I've promised to the subsystem maintainer:
- remove a pair of extra brackets,
- drop useless case for not possible v4l2_mbus_pixelcode enum value of 0.
Created against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix an outstanding typo in the recently added driver, as requested by
the subsystem maintainer.
Created against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recent locking related videobuf changes has not been incorporated into the new
OMAP1 camera driver. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The recently added OMAP1 camera driver was not ready for one video queue per
device framework changes. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have two dma engines in MX3 systems: The IPU and the SDMA
engine. We have to check if we got a channel from the correct
engine before proceeding with a channel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason, commit 1aafeb30104a is missing one change that was
included in the email submission.
The sensor configuration must be passed down to the ov7670 subdev.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The entries for those cards are after the generic entries,
so they don't work, in practice. Moving them to happen before the
generic entres fix the issue.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All of the hard problems for BKL removal appear to be solved in the
v4l-dvb/master tree. This removes the BKL from the various open
functions that do not need it, or only use it to protect an
open count.
The zoran driver is nontrivial in this regard, so I introduce
a new mutex that locks both the open/release and the ioctl
functions. Someone with access to the hardware can probably
improve that by using the existing lock in all cases.
Finally, all drivers that still use the locked version of the
ioctl function now get called under a new mutex instead of
the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit a90f933507 accidentally removed
the piece of code setting the i2c algo pointer. Restore it.
That's what happens when you put two code statements on the same
line...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We were forgetting to set up proper return value in success path causing
ir_getkeycode() to fail intermittently:
drivers/media/IR/ir-keytable.c: In function 'ir_getkeycode':
drivers/media/IR/ir-keytable.c:363: warning: 'retval' may be used
uninitialized in this function
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The input-large-scancode patches changed the binary search in
drivers/media/IR/ir-keytable.c to use unsigned integers, but
signed integers are actually necessary for the algorithm to work.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The VIA Chrome integrated camera controller driver includes both 'linux/pci.h'
and 'linux/device.h' twice. This gets rid of the duplicates.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
Changeset 1724c8fa7e added an option to change
the maximum I2C size to 8 bytes. However, it forgot to replace the previous
usage at af9015 to use the newly defined macro value
(TDA18271_16_BYTE_CHUNK_INIT).
A latter changeset (e350d44fed) extended the
possible values for .small_i2c field and, instead of using a random sequence
of numbers, it used a number that makes more sense (e. g. the actual limit,
in terms of bytes).
However, as af9015 were using .small_i2c = 1, this become undefined, and the
restriction of a max size of 16 was gone.
While here, fix the reported msg size at tda18271-common.c.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Few drivers still have assumption that ir_raw_event
consists of duration and pulse flag.
Fix that.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
I managed to trigger a divide by 0 in the v4l compat code
with the mem2mem test module; I suspect perhaps it shouldn't
have been returning a 0 pixel wide picture, but either way it seems
right to guard this divide by 0 in the compatibility layer.
Tested on 2.6.36 (ubuntu build, but the code in this is the same as upstream),
but ***not tested with a real video device***.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
cc: stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pointed out by Bonne Eggleston on the lirc list.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a redundant call to imon_ir_change_protocol -- its already
getting called from ir_input_register. Also do some minor housekeeping
with var names and formatting.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Somehow, I managed to screw things up when reworking the rdev/idev split
patch from David, and started trying to get ir_input_dev from idev
instead of rdev, thus resulting in button presses hanging the system.
This fixes it.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Force smbus communication, disable QCIF mode, and set the correct
clock speed on the OLPC XO-1.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These parameters need to be configurable based on the host system.
They can now be communicated through the s_config call.
The old CONFIG_OLPC_XO_1 selector was not correct; this kind of
arrangement wouldn't allow for a universal kernel that would work on both
laptops.
Certain parts of the probe routine had to be moved later (into s_config),
because we can't do any I/O until we know which I/O method has been
selected through this mechanism.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is AF9015+AF9013+2xMXL5007T.
Tanks to Bernard Giannetti and DigitalNow for the help!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Renura Enterprises Pty Ltd <renura@digitalnow.com.au>
Cc: Bernard Giannetti <thebernmeister@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Read all remote controller registers at once to reduce USB remote polling traffic.
Use .rc_codes() to disable / enable remote polling instead of .rc_query().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Digital Everywhere firmware have the shortcoming that ca_info_enq and
ca_info are not supported. This means that we can never retrieve the correct
ca_system_id to present in the CI message CA_INFO. Currently the driver uses
the application id retrieved using app_info_req and app_info, but this id
only match the correct ca_system_id as given in ca_info in some cases.
This patch adds a parameter to the driver in order for the user to override
what will be returned in the CA_INFO CI message. Up to four ca_system_ids can
be specified.
This is needed for users with CAMs that have different manufacturer id and
ca_system_id and that uses applications that take this into account, like
MythTV.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Lawrence Rust <lawrence@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- serialize the suspend and resume functions using the global lock.
- do not call usb_autopm_put_interface after a disconnect.
- fix a race when disconnecting the device.
Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: David Ellingsworth<david@identd.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Indent the branch of an if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These include
-later kill of usb_buffer to avoid kernel crash on hot unplugging.
-DiSEqC functions.
-LNB Power switch
-Faster channel change.
-support for LG tuner on LME2510C.
-firmware switching for LG tuner.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
> From: Dan Carpenter [mailto:error27@gmail.com]
>
> These are signed so instead of being 1 and 0 as intended they are -1 and
> 0. It doesn't cause a bug in the current code but Sparse warns about
> it:
>
> drivers/media/video/s5p-fimc/fimc-core.h:226:28:
> error: dubious one-bit signed bitfield
> struct fimc_scaler {
> - int scaleup_h:1;
> - int scaleup_v:1;
> - int copy_mode:1;
> - int enabled:1;
> + unsigned int scaleup_h:1;
> + unsigned int caleup_v:1;
> + unsigned int copy_mode:1;
> + unsigned int enabled:1;
In general I agree, however this patch would change scaleup_v:1
to caleup_v, so it cannot be applied in current form.
Here is the corrected patch:
Reported-by: Dan Carpenter <error27@gmail.com<
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap
