Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.
On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a result of the USB 2.0 clocks not being disabled/enabled
during suspend/resume on XHCI only systems.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BDC "Read Transaction Size" needs to be changed from 1024
bytes to 256 bytes to prevent occasional transaction failures.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When there is no device connected and FSM is enabled, the XHCI puts
the PHY into suspend mode. When the PHY is put into suspend mode
the USB LDO powers down the PHY. This causes the MDIO to be
inaccessible and its registers reset to default. The fix is to
disable FSM.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Handle defer on clk_get because the new SCMI clock driver comes
up after this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7211b0 has added the STB XHCI Synopsys controller and it
will be used instead of the RPi based DWC USB controller. The new
Synopsys XHCI controller core is the same one that is used on the
7216, but because of the way the STB USB PHY is used on both the A0
and B0, some of the PHY control is different.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7216 has the new USB XHCI controller from Synopsys. While
this new controller and the PHY are similar to the STB versions,
the major differences are:
- Many of the registers and fields in the CTRL block have been
removed or changed.
- A new set of Synopsys control registers, BCHP_USB_XHCI_GBL, were
added.
- MDIO functionality has been replaced with direct access registers
in the BCHP_USB_XHCI_GBL block.
- Power up PHY defaults that had to be changed by MDIO in previous
chips will now power up with the correct defaults.
A new init module was created for this new Synopsys USB controller.
A new compatible string was added and the driver will dispatch
into one of two init modules based on it. A "reg-names" field was
added so the driver can more easily get optional registers.
A DT bindings document was also added for this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver is being restructured in preparation for adding support
for the new Synopsys USB conroller on the 7216. Since all the bugs
and work-arounds in previous STB chips are supposed to be fixed,
most of the code in phy-brcm-usb-init.c is not needed. Instead of
adding more complexity to the already complicated phy-brcm-usb-init.c
module, the driver will be restructured to use a vector table to
dispatch into different C modules for the different controllers.
There was also some general cleanup done including some ipp setup
code that was incorrect.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the ability to handle USB wake events from USB devices when
in S2 mode. Typically there is some additional configuration
needed to tell the USB device to generate the wake event when
suspended but this varies with the different USB device classes.
For example, on USB Ethernet dongles, ethtool should be used to
enable the magic packet wake functionality in the dongle.
NOTE: This requires that the "power/wakeup" sysfs entry for
the USB device generating the wakeup be set to "enabled".
This functionality requires a special hardware sideband path that
will trigger the AON_PM_L2 interrupt needed to wake the system from
S2 even though the USB host controllers are in IDDQ (low power state)
and most USB related clocks are shut off. For the sideband signaling
to work we need to leave the usbx_freerun clock running, but this
clock consumes very little power by design. There's a bug in the
XHCI wake hardware so only EHCI/OHCI wake is currently supported.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the Phy driver will put the USB phys into the max
power saving mode (IDDQ) when there is no corresponding XHCI, EHCI
or OHCI client (through rmmod, unbind or if the driver is not
builtin). This change will also put the Phys into IDDQ mode
on suspend so that S2 will get the additional power savings.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BRCM USB Phy, ohci, ehci and xhci drivers all use the USB clocks
but not all drivers use the clk_prepare_enable/clk_disable_unprepare
versions to enable/disable the clocks. This change gets all drivers
using the prepare version.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the EHCI controller received a 512 byte USB packet that
had to be broken into 2 256 byte bursts across the SCB bus AND
there was a following 512 byte USB packet, the second burst of
data from the first packet was sometimes being lost. If the
burst size was changed to 128 bytes via the EBR_SCB_SIZE field
in the USB_CTRL_EBRIDGE register we'd see the 4th 128 byte burst
of the first packet being lost. This problem became much worse
if other threads were running that accessed memory, like a memcpy
test. Setting the EBR_SCB_SIZE to 512, which prevents breaking
the EHCI USB packet (max size of 512 bytes) into bursts, fixed
the problem.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
7216 is a 16nm process chip with a slightly different version of the PHY
SerdDeS/AFE that requires a specific tuning sequence. Key on the
compatible string to perform that initialization.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The xhci_ec_base variable is a pointer, so don't compare
it with an integer.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=5mPE
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
phy: for 5.3
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
dt-bindings: phy: Add documentation for mixel dphy
dt-bindings: phy-pxa-usb: add bindings
phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
phy: qcom-qmp: Correct READY_STATUS poll break condition
phy: ti: am654-serdes: Make serdes_am654_xlate() static
phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
phy: samsung: Use struct_size() in devm_kzalloc()
phy: qcom: Add Qualcomm PCIe2 PHY driver
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=+dGx
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2-rc
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: tegra: xusb: Add Tegra210 PLL power supplies
phy: tegra: xusb: Add Tegra124 PLL power supplies
dt-bindings: phy: tegra-xusb: List PLL power supplies
phy: usb: phy-brcm-usb: Remove sysfs attributes upon driver removal
phy: renesas: rcar-gen2: Fix memory leak at error paths
phy: qcom-qusb2: fix missing assignment of ret when calling clk_prepare_enable
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are not destroying the sysfs attribute groupe we registered during
the probe function which will make subsequent probe calls to that
driver fail. Correct that with adding a remove function which only
removes those attributes since the reference counting on clocks did its
job already.
Fixes: 415060b21f ("phy: usb: phy-brcm-usb: Add ability to force DRD mode to host or device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 44 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.032047323@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB PHY driver supports two types of stingray USB PHYs
- Type 1 is a combo PHY contains two PHYs, one SS and one HS.
- Type 2 is a single HS PHY.
These two PHY versons support both Generic xHCI host controller driver
and BDC Broadcom device controller driver.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When PIPEMIX=1, change the operation from 2x8 EP to 1x8 EP + 1x8 RC.
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BCM63138 SATA PHY requires a special initialization sequence in
order to operate correctly, mostly tuning incorrect default values.
Implement that sequence and match the documented compatible string as an
entry point into that sequence.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Broadcom ARM-based DSL SoCs (BCM63xx product line) have the same
Broadcom SATA PHY that other SoCs are using, make it possible to select
that driver on these platforms.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO has implemented the if(IS_ERR(...)) + PTR_ERR, So
just replace them rather than duplicating its implement.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add Stingray PCIe PHY driver for both PAXB and PAXC root complex
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Unset is required to enable USB 3.0 PHY when XHCI reenabled in response
to setting PHY3_IDDQ_OVERRIDE in uninit().
Fixes: cd6f769fde ("phy: phy-brcm-usb-init: Power down USB 3.0 PHY when XHCI disabled")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver patches,
there are some PHY driver fixes, license cleanups, sysfs attribute
cleanups, usbip changes, and a raft of other smaller fixes and
additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnL0Bg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymg8gCeLg/FMtc0S/xRR/56N/sbthEebcUAnROr9Sg3
55hDLdkyi93o9R86YOAJ
=8d2q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver
patches, there are some PHY driver fixes, license cleanups, sysfs
attribute cleanups, usbip changes, and a raft of other smaller fixes
and additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues"
* tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits)
USB: serial: pl2303: new device id for Chilitag
USB: misc: fix up some remaining DEVICE_ATTR() usages
USB: musb: fix up one odd DEVICE_ATTR() usage
USB: atm: fix up some remaining DEVICE_ATTR() usage
USB: move many drivers to use DEVICE_ATTR_WO
USB: move many drivers to use DEVICE_ATTR_RO
USB: move many drivers to use DEVICE_ATTR_RW
USB: misc: chaoskey: Use true and false for boolean values
USB: storage: remove old wording about how to submit a change
USB: storage: remove invalid URL from drivers
usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found
usbip: list: don't list devices attached to vhci_hcd
usbip: prevent bind loops on devices attached to vhci_hcd
USB: serial: remove redundant initializations of 'mos_parport'
usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
usb: gadget: compress return logic into one line
usbip: vhci_hcd: update 'status' file header and format
USB: serial: simple: add Motorola Tetra driver
CDC-ACM: apply quirk for card reader
usb: option: Add support for FS040U modem
...
The newly introduced calibrate function has a variable
that has never been used and needs to be removed to avoid
this harmless warning:
drivers/phy/broadcom/phy-brcm-sata.c: In function 'brcm_stb_sata_calibrate':
drivers/phy/broadcom/phy-brcm-sata.c:514:24: error: unused variable 'priv' [-Werror=unused-variable]
Fixes: 3e507769d1 ("phy: brcm-sata: Implement calibrate callback")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Implement the calibration callback to allow turning on the Clock-Data
Recovery module clamping when necessary, e.g: during failure to identify
a SATA hard drive from ahci_brcm.c::brcm_ahci_read_id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is caused by a bug in the BDC core. When the BDC core comes
out of reset and it's not selected, it gets a backup clock. When
the BDC core is selected, it get's the main clock. If HOST mode
is then selected the BDC core has the main clock shut off but
the backup clock is not restored.
The failure scenario and cause are as follows:
- DRD mode is active
- Device mode is selected first in bootloader
- When host mode is now selected, the clock to the BDC is cut off.
- BDC registers are inaccessible and therefore the BDC driver
crashes upon Linux boot.
The fix is to have the phy driver always force a BDC reset on
startup.
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Set PHY3_IDDQ_OVERRIDE in the xhci uninit routine. This will save
additional power when the XHCI driver is not enabled.
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable the the Low Speed Keep Alive signal on the 7271b0 by setting
the LS_KEEP_ALIVE bit in the USB CTRL OBRIDGE register otherwise
some Dell Low Speed keyboards fail.
Also do a little cleanup of the EBRIDGE ESTOP_SCB_REQ bit. Since
this is only used on one platform, remove it from the platform
tables and just use "if (family == ").
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Change "brcm,has_xhci" and "brcm,has_eohci" device tree properties
to the preferred "brcm,has-xhci" and "brcm,has-eohci". This also
matches the existing device tree bindings document.
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gWvl
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-next
Chanwoo writes:
Update extcon for 4.15
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
Parse the DT properties brcm,rxaeq-mode and brcm,rxaeq-value to
correctly configure the RX equalizer of the PHY. This may be required to
resolve specific signal integrity issues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Split the functional code in brcm_stb_sata_init() to a separate function
that actually does configure spread spectrum: brcm_stb_sata_ssc_init()
and make that function return void, since that function cannot fail.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
When the usb phy device mode is set to "drd", the USB port will
switch between device and host modes depending on what's plugged
into the port. Customers have asked for the ability to force
host or device mode from software. This commit adds sysfs
entries to the phy device that allow this. The sysfs for the phy
device can be found at:
/sys/bus/platform/drivers/brcmstb-usb-phy/*.usb-phy
The following sysfs entries were added:
- "dr_mode" (RO) - The current phy "dr_mode" setting.
It will be set to one of the following values:
- "host" - host mode
- "peripheral " - device mode
- "drd" - switch between device and host mode based on
installed device
- "typec-pd" - device/host mode is controller by the USB
Type-C PD protocol.
If "dr_mode" is "drd"
- "drd_select" (RW) -
It will be set to one of the following values:
- "host" - force host mode
- "device" - force device mode
- "auto" - allow normal auto selection of host/device based on
inserted USB device
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new USB Phy driver for Broadcom STB SoCs. This driver
supports Broadcom STB ARM SoCs. This driver in
combination with the Broadcom STB ohci, ehci and xhci
drivers will enable USB1.1, USB2.0 and USB3.0 support.
This Phy driver also supports the Broadcom BDC gadget
driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa1+Ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl26wCgquufNylfhxr65NbJrovduJYzRnUAniCivXg8
bePIh/JI5WxWoHK+wEbY
=hYWx
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while"
* tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (244 commits)
ANDROID: binder: don't queue async transactions to thread.
ANDROID: binder: don't enqueue death notifications to thread todo.
ANDROID: binder: Don't BUG_ON(!spin_is_locked()).
ANDROID: binder: Add BINDER_GET_NODE_DEBUG_INFO ioctl
ANDROID: binder: push new transactions to waiting threads.
ANDROID: binder: remove proc waitqueue
android: binder: Add page usage in binder stats
android: binder: fixup crash introduced by moving buffer hdr
drivers: w1: add hwmon temp support for w1_therm
drivers: w1: refactor w1_slave_show to make the temp reading functionality separate
drivers: w1: add hwmon support structures
eeprom: idt_89hpesx: Support both ACPI and OF probing
mcb: Fix an error handling path in 'chameleon_parse_cells()'
MCB: add support for SC31 to mcb-lpc
mux: make device_type const
char: virtio: constify attribute_group structures.
Documentation/ABI: document the nvmem sysfs files
lkdtm: fix spelling mistake: "incremeted" -> "incremented"
perf: cs-etm: Fix ETMv4 CONFIGR entry in perf.data file
nvmem: include linux/err.h from header
...
Krzysztof Kozlowski