mirror of https://gitee.com/openkylin/linux.git
10658 Commits
| Author | SHA1 | Message | Date |
|---|---|---|---|
Sebastian Reichel
|
96d3bb1a0e |
ARM: dts: N950: Add wlan support
Add support for the wl1271 wlan chip. As far as I can see N9 uses the same chip with the same enable and irq gpio, but they use the mmc interface instead of the spi interface. Signed-off-by: Sebastian Reichel <sre@kernel.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com> |
|
|
Uri Mashiach
|
444d66fafa |
ARM: dts: add spi wifi support to cm-t335
Device tree modifications: - Pinmux for SPI0 and WiFi GPIOs. - SPI0 node with wlcore as a child node. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com> |
|
|
Uri Mashiach
|
48ab364478 |
ARM: dts: cm-t335: add audio support
The TLV320AIC23B codec is connected to the CPU by McASP controller 1 for data and I2C0 for control. Modifications: - Enable and configure McASP controller 1. - Add TLV320AIC23B codec pinmux. - Add TLV320AIC23B codec configurations. - Use simple-audio-card as CPU to codec glue. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com> |
|
|
Uri Mashiach
|
511fc6d85b |
ARM: dts: cm-t335: add touchscreen support
Touchscreen and analog digital converter configurations. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com> |
|
|
Uri Mashiach
|
2ac6e66ed6 |
ARM: dts: cm-t335: Add support for CAN bus
Add CAN bus pinmux. Enable D_CAN bus controllers 0 and 1 The pinmux of uart1 node contradicts the pinmux of dcan0 and dcan1 nodes. U-Boot should delete the uart1 or dcan0/1 nodes. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com> |
|
|
Pali Rohár
|
12e47442c2 |
ARM: dts: omap3: Include missing bandgap data for ti-soc-thermal driver
Driver for omap3 with documentation is there since v4.4-rc1. Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Tested-by: Pavel Machek <pavel@ucw.cz> [tony@atomide.com: added thermal-sensor-cells as suggested by Roger] Signed-off-by: Tony Lindgren <tony@atomide.com> |
|
|
Pali Rohár
|
14628e4444 |
ARM: dts: n900: Include adp1653 device
This patch adds adp1653 device into n900 DT structure. DT support in adp1653 driver is there since v4.2-rc1 version. Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> |
|
|
Linus Torvalds
|
1b8ee1ec41 |
ARM: SoC fixes for v4.5 merge window
A few fixes for fallout that we didn't catch in time in -next, or smaller warning fixes that have been discovered since. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJWolruAAoJEIwa5zzehBx3wIsQAJzOv9kJIw7c+Uh8Wu2CkEmv IJMiL8n7PvtLq/USOYKKIqf6KeGjedMNM1aFSRuDQ0HqdBB4ysyv4Go6CMUlxSv7 fbr5/AmZlrgBKZwvjh2SzehvvhuaWuDMzo+1lDm2cqQ8u/kmEQPcDRG/eTDDV5nf Ym/dDCh8PXHTFmuad2a3qznNod5kHNE+agOgjTYZxZvA67Ys8HGoaXlYtJijqv5p KwcNspT0vn7Tf22XrEsrkR9bgfyNHcdiB+qSJBYWqH00Q0ew6zfLI1FWPUNPLvg6 HgoNIxBIaNdPS9v/EH70uhvIeWGTH0Yz/YiNzm3lp+rIWutdDPnKW0DnxiIACGis e9b4f24OfPWeveh+KWdVgyRYk/hNvO9umuJNyM6G2PP9fWRldqZXfR0vVKY6Wfzr WYprBAbY/LvuZBsyser3UNokD2pxaLGCTrkRiH/Y/hQuhfu8HjDmetoKI5Vz8Irn 2/rAWL0yidpblPd6hZAbz0b/Z2SCRU+eRF6Q10ovr9Ug3AY8oEKrlt6emcbDoFie 1geHAJT+HGejR4Hl9rEixZQqJ0o2BtyyETqZpM1hY6eOE7uz/bw59kfjLLCCHcr7 mZx9DUjAH5trkvPVlj/WUXPoryW9Ra66eREXsIwajBQb53ww6gdr/VAYCYFDx/VF V10Vs46iT8lLoqY/YsT/ =PRjJ -----END PGP SIGNATURE----- Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "A few fixes for fallout that we didn't catch in time in -next, or smaller warning fixes that have been discovered since" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: soc: qcom/spm: shut up uninitialized variable warning ARM: realview: fix device tree build ARM: debug-ll: fix BCM63xx entry for multiplatform ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz |
|
|
Olof Johansson
|
53c517a837 |
Renesas ARM Based SoC Fixes for v4.5
Correct extal1 frequency of armadillo800eva board -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJWoESmAAoJENfPZGlqN0++RsMP/1q9XvQYUc6xF0LqQR8jLx3N FGt/uHiWEzkprfMNRAimX3l6UDv+ae44S58kyCjfOEwz9H58JtFnhlg+Ofq8+ibu UklF/niPl4UvjPaNaeIZIoBlt6CdjnO53nzCTjCsT7kGv1lYHE+2UCwFiuQtQdSB pH0frq+kDlSpSumiMlsmwajVqf/5kWjoRvhLTztKeB6soxlVFkX3FoKURnCQhaXJ J7agAC8hK8vBwL3xUXCTL9ozBxlkgCY7uwenDr97mCQfl5aEvtOcXhLxafhetuKM ZvgD1BO2u4lAQDoEFEw3X4T9To4R2PNvgNslhTuMLBM3EUa4kvZTykM6PKitE506 cTHwCzvI2JnXK6h7ySLQWVDwG8/gGAjCbvt5ZXztOrb7Nqu3kr5hizcbHKBYCWfu 7WOxqFbBj2j+D4TqzFh8B6si4IQG8ZPOCa9gmtpz1FeE6Yg5/gM3cV+1DP6/VxJ+ C5OqjNUPK8DKOu0ZTpR1DqsDtIfJ/O+psk6AlLigg4GzkIuTZQ8nDVOTaUtnk2G8 MTF2IWgd0x5659mhvDOCj3F4IsfjHS2zuczAnU4eCDcHLuplAguOrtG/NnP+egTI nGlsF+DFXkOXhz/vkvS7AgJwAhAm2KXgtLCA9LvNxfz9youZKc/CbxwDVPV/cq9F RSvr3ktkSYro+q8Wx6ch =YGew -----END PGP SIGNATURE----- Merge tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes Renesas ARM Based SoC Fixes for v4.5 Correct extal1 frequency of armadillo800eva board * tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz Signed-off-by: Olof Johansson <olof@lixom.net> |
|
|
Linus Torvalds
|
d43421565b |
PCI changes for the v4.5 merge window:
Enumeration
Simplify config space size computation (Bjorn Helgaas)
Avoid iterating through ROM outside the resource window (Edward O'Callaghan)
Support PCIe devices with short cfg_size (Jason S. McMullan)
Add Netronome vendor and device IDs (Jason S. McMullan)
Limit config space size for Netronome NFP6000 family (Jason S. McMullan)
Add Netronome NFP4000 PF device ID (Simon Horman)
Limit config space size for Netronome NFP4000 (Simon Horman)
Print warnings for all invalid expansion ROM headers (Vladis Dronov)
Resource management
Fix minimum allocation address overwrite (Christoph Biedl)
PCI device hotplug
acpiphp_ibm: Fix null dereferences on null ibm_slot (Colin Ian King)
pciehp: Always protect pciehp_disable_slot() with hotplug mutex (Guenter Roeck)
shpchp: Constify hpc_ops structure (Julia Lawall)
ibmphp: Remove unneeded NULL test (Julia Lawall)
Power management
Make ASPM sysfs link_state_store() consistent with link_state_show() (Andy Lutomirski)
Virtualization
Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 (Tim Sander)
MSI
Remove empty pci_msi_init_pci_dev() (Bjorn Helgaas)
Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD (Grygorii Strashko)
Initialize MSI capability for all architectures (Guilherme G. Piccoli)
Relax msi_domain_alloc() to support parentless MSI irqdomains (Liu Jiang)
ARM Versatile host bridge driver
Remove unused pci_sys_data structures (Lorenzo Pieralisi)
Broadcom iProc host bridge driver
Hide CONFIG_PCIE_IPROC (Arnd Bergmann)
Do not use 0x in front of %pap (Dmitry V. Krivenok)
Update iProc PCIe device tree binding (Ray Jui)
Add PAXC interface support (Ray Jui)
Add iProc PCIe MSI device tree binding (Ray Jui)
Add iProc PCIe MSI support (Ray Jui)
Freescale i.MX6 host bridge driver
Use gpio_set_value_cansleep() (Fabio Estevam)
Add support for active-low reset GPIO (Petr Štetiar)
HiSilicon host bridge driver
Add support for HiSilicon Hip06 PCIe host controllers (Gabriele Paoloni)
Intel VMD host bridge driver
Export irq_domain_set_info() for module use (Keith Busch)
x86/PCI: Allow DMA ops specific to a PCI domain (Keith Busch)
Use 32 bit PCI domain numbers (Keith Busch)
Add driver for Intel Volume Management Device (VMD) (Keith Busch)
Qualcomm host bridge driver
Document PCIe devicetree bindings (Stanimir Varbanov)
Add Qualcomm PCIe controller driver (Stanimir Varbanov)
dts: apq8064: add PCIe devicetree node (Stanimir Varbanov)
dts: ifc6410: enable PCIe DT node for this board (Stanimir Varbanov)
Renesas R-Car host bridge driver
Add support for R-Car H3 to pcie-rcar (Harunobu Kurokawa)
Allow DT to override default window settings (Phil Edworthy)
Convert to DT resource parsing API (Phil Edworthy)
Revert "PCI: rcar: Build pcie-rcar.c only on ARM" (Phil Edworthy)
Remove unused pci_sys_data struct from pcie-rcar (Phil Edworthy)
Add runtime PM support to pcie-rcar (Phil Edworthy)
Add Gen2 PHY setup to pcie-rcar (Phil Edworthy)
Add gen2 fallback compatibility string for pci-rcar-gen2 (Simon Horman)
Add gen2 fallback compatibility string for pcie-rcar (Simon Horman)
Synopsys DesignWare host bridge driver
Simplify control flow (Bjorn Helgaas)
Make config accessor override checking symmetric (Bjorn Helgaas)
Ensure ATU is enabled before IO/conf space accesses (Stanimir Varbanov)
Miscellaneous
Add of_pci_get_host_bridge_resources() stub (Arnd Bergmann)
Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask (Bjorn Helgaas)
Fix all whitespace issues (Bogicevic Sasa)
x86/PCI: Simplify pci_bios_{read,write} (Geliang Tang)
Use to_pci_dev() instead of open-coding it (Geliang Tang)
Use kobj_to_dev() instead of open-coding it (Geliang Tang)
Use list_for_each_entry() to simplify code (Geliang Tang)
Fix typos in <linux/msi.h> (Thomas Petazzoni)
x86/PCI: Clarify AMD Fam10h config access restrictions comment (Tomasz Nowicki)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z9mQ
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v4.5 merge window:
Enumeration:
- Simplify config space size computation (Bjorn Helgaas)
- Avoid iterating through ROM outside the resource window (Edward O'Callaghan)
- Support PCIe devices with short cfg_size (Jason S. McMullan)
- Add Netronome vendor and device IDs (Jason S. McMullan)
- Limit config space size for Netronome NFP6000 family (Jason S. McMullan)
- Add Netronome NFP4000 PF device ID (Simon Horman)
- Limit config space size for Netronome NFP4000 (Simon Horman)
- Print warnings for all invalid expansion ROM headers (Vladis Dronov)
Resource management:
- Fix minimum allocation address overwrite (Christoph Biedl)
PCI device hotplug:
- acpiphp_ibm: Fix null dereferences on null ibm_slot (Colin Ian King)
- pciehp: Always protect pciehp_disable_slot() with hotplug mutex (Guenter Roeck)
- shpchp: Constify hpc_ops structure (Julia Lawall)
- ibmphp: Remove unneeded NULL test (Julia Lawall)
Power management:
- Make ASPM sysfs link_state_store() consistent with link_state_show() (Andy Lutomirski)
Virtualization
- Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 (Tim Sander)
MSI:
- Remove empty pci_msi_init_pci_dev() (Bjorn Helgaas)
- Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD (Grygorii Strashko)
- Initialize MSI capability for all architectures (Guilherme G. Piccoli)
- Relax msi_domain_alloc() to support parentless MSI irqdomains (Liu Jiang)
ARM Versatile host bridge driver:
- Remove unused pci_sys_data structures (Lorenzo Pieralisi)
Broadcom iProc host bridge driver:
- Hide CONFIG_PCIE_IPROC (Arnd Bergmann)
- Do not use 0x in front of %pap (Dmitry V. Krivenok)
- Update iProc PCIe device tree binding (Ray Jui)
- Add PAXC interface support (Ray Jui)
- Add iProc PCIe MSI device tree binding (Ray Jui)
- Add iProc PCIe MSI support (Ray Jui)
Freescale i.MX6 host bridge driver:
- Use gpio_set_value_cansleep() (Fabio Estevam)
- Add support for active-low reset GPIO (Petr Štetiar)
HiSilicon host bridge driver:
- Add support for HiSilicon Hip06 PCIe host controllers (Gabriele Paoloni)
Intel VMD host bridge driver:
- Export irq_domain_set_info() for module use (Keith Busch)
- x86/PCI: Allow DMA ops specific to a PCI domain (Keith Busch)
- Use 32 bit PCI domain numbers (Keith Busch)
- Add driver for Intel Volume Management Device (VMD) (Keith Busch)
Qualcomm host bridge driver:
- Document PCIe devicetree bindings (Stanimir Varbanov)
- Add Qualcomm PCIe controller driver (Stanimir Varbanov)
- dts: apq8064: add PCIe devicetree node (Stanimir Varbanov)
- dts: ifc6410: enable PCIe DT node for this board (Stanimir Varbanov)
Renesas R-Car host bridge driver:
- Add support for R-Car H3 to pcie-rcar (Harunobu Kurokawa)
- Allow DT to override default window settings (Phil Edworthy)
- Convert to DT resource parsing API (Phil Edworthy)
- Revert "PCI: rcar: Build pcie-rcar.c only on ARM" (Phil Edworthy)
- Remove unused pci_sys_data struct from pcie-rcar (Phil Edworthy)
- Add runtime PM support to pcie-rcar (Phil Edworthy)
- Add Gen2 PHY setup to pcie-rcar (Phil Edworthy)
- Add gen2 fallback compatibility string for pci-rcar-gen2 (Simon Horman)
- Add gen2 fallback compatibility string for pcie-rcar (Simon Horman)
Synopsys DesignWare host bridge driver:
- Simplify control flow (Bjorn Helgaas)
- Make config accessor override checking symmetric (Bjorn Helgaas)
- Ensure ATU is enabled before IO/conf space accesses (Stanimir Varbanov)
Miscellaneous:
- Add of_pci_get_host_bridge_resources() stub (Arnd Bergmann)
- Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask (Bjorn Helgaas)
- Fix all whitespace issues (Bogicevic Sasa)
- x86/PCI: Simplify pci_bios_{read,write} (Geliang Tang)
- Use to_pci_dev() instead of open-coding it (Geliang Tang)
- Use kobj_to_dev() instead of open-coding it (Geliang Tang)
- Use list_for_each_entry() to simplify code (Geliang Tang)
- Fix typos in <linux/msi.h> (Thomas Petazzoni)
- x86/PCI: Clarify AMD Fam10h config access restrictions comment (Tomasz Nowicki)"
* tag 'pci-v4.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183
PCI: Limit config space size for Netronome NFP4000
PCI: Add Netronome NFP4000 PF device ID
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
PCI: host: Add of_pci_get_host_bridge_resources() stub
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
PCI: rcar: Add Gen2 PHY setup to pcie-rcar
PCI: rcar: Add runtime PM support to pcie-rcar
PCI: designware: Make config accessor override checking symmetric
PCI: ibmphp: Remove unneeded NULL test
ARM: dts: ifc6410: enable PCIe DT node for this board
ARM: dts: apq8064: add PCIe devicetree node
PCI: hotplug: Use list_for_each_entry() to simplify code
PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar
PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers
PCI: Avoid iterating through memory outside the resource window
PCI: acpiphp_ibm: Fix null dereferences on null ibm_slot
...
|
|
|
Linus Torvalds
|
6d1c244803 |
ARM: DT updates for v4.5
As usual, the bulk of this release is again DT file contents. There's a huge number of changes here, and it's challenging to give a crisp overview of just what is in here. To start with: New boards: - TI-based DM3730 from LogicPD (Torpedo) - Cosmic+ M4 (nommu) initial support (Freescale Vybrid) - Raspberry Pi 2 DT files - Watchdog on Meson8b - Veyron-mickey (ASUS Chromebit) DTS - Rockchip rk3228 SoC and eval board - Sigma Designs Tango4 Improvements: - Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files - Misc new devices for Rockchip rk3036 and rk3288 - Allwinner updates for misc SoCs and systems ... and a _large_ number of other changes across the field. Devices added to SoC DTSI and board DTS files for a number of SoC vendors, new product boards on already-supported SoCs, cleanups and refactorings of existing DTS/DTSI files and a bunch of other changes. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJWnr6fAAoJEIwa5zzehBx3p+gP+wYLUqXjCYgyu6oJPxJbWghj gPc4QJmhVlAWTqvE7Ut7RumWzGa7nUEH2QF9tiCLbDAw8727HJXhRHknFwaCsX45 BsvFQaKY99ClfUhoSI9GRa8e2jEArjzEPqkynHW/8FM20qWaj/Z8DDfixG75gR8u onrMw6kprNGwmyQwqu5zLDXhUBCQIs1xRRSabUjV1P5420dbBaGgtmQrdj7k+JDt wo9SKiG6d9CSYil3r7BC+0JwzbKNBxRGs2vv1BJOfbZ3Lj+uC0vj1AxoF/p7dOHy ohuvt7UwwtoUzzFMcMUo7E8qxl9u6bbnPDlUoRF7DVVi5SQoeZd8BOZXOdLRN2OQ qtgsmziDxtvh7Ydj6i89D69x7+GurAFcP8Aturprc5Zd5lO70PAYBD379IhIZ8y1 MVJltIEeuUZo7BaVBCHWQY9jJRtI3bAU6JdFPrFROsuo810IYd72Wbb1ZCfF7SV7 nBRvV7e71VQxb48c3p8Et5FntHuXfUlhkMrQ7Cb+2ugB/diGgZB9NfrZbP3Azv7f A5Ey9tNHaOCUxzYDCw80jTa7OwVWNJf2kOT1yikASk3vODKLv4E5YQ2DULnObWG7 iRmLYuuGka4sMs0ZjpV3kaqs+8rWu08x2rEr5X0wfU+DalIzUWA2oDKSgPLJoacV gXKP039CIxQAiottcppA =XDLa -----END PGP SIGNATURE----- Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM DT updates from Olof Johansson: "As usual, the bulk of this release is again DT file contents. There's a huge number of changes here, and it's challenging to give a crisp overview of just what is in here. To start with: New boards: - TI-based DM3730 from LogicPD (Torpedo) - Cosmic+ M4 (nommu) initial support (Freescale Vybrid) - Raspberry Pi 2 DT files - Watchdog on Meson8b - Veyron-mickey (ASUS Chromebit) DTS - Rockchip rk3228 SoC and eval board - Sigma Designs Tango4 Improvements: - Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files - Misc new devices for Rockchip rk3036 and rk3288 - Allwinner updates for misc SoCs and systems ... and a _large_ number of other changes across the field. Devices added to SoC DTSI and board DTS files for a number of SoC vendors, new product boards on already-supported SoCs, cleanups and refactorings of existing DTS/DTSI files and a bunch of other changes" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits) ARM: dts: compulab: add new board description ARM: versatile: add the syscon LEDs to the DT dts: vt8500: Fix errors in SDHC node for WM8505 ARM: dts: imx6q: clean up unused ipu2grp ARM: dts: silk: Add compatible property to "partitions" node ARM: dts: gose: Add compatible property to "partitions" node ARM: dts: porter: Add compatible property to "partitions" node ARM: dts: koelsch: Add compatible property to "partitions" node ARM: dts: lager: Add compatible property to "partitions" node ARM: dts: bockw: Add compatible property to "partitions" node ARM: dts: meson8b: Add watchdog node Documentation: watchdog: Add new bindings for meson8b ARM: meson: Add status LED for Odroid-C1 ARM: dts: uniphier: fix a typo in comment block ARM: bcm2835: Add the auxiliary clocks to the device tree. ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT. ARM: bcm2835: Split the DT for peripherals from the DT for the CPU ARM: realview: set up cache correctly on the PB11MPCore ARM: dts: Unify G2D device node with other devices on exynos4 ... |
|
|
Linus Torvalds
|
1305eda751 |
ARM: SoC platform updates for v4.5
Updates for new platform support: - New platform: Tango4 from Sigma Designs. - Broadcom BCM2836 (Raspberry Pi 2 SoC) - Enable cpufreq on Freescale i.MX7D - Rockchip: SMP support for rk3036, general support for rk3228 - SMP support on Broadcom Kona and NSP - Cleanups for OMAP removing legacy IOMMU data + a bunch of misc fixes and tweaks for various platforms. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJWnrvIAAoJEIwa5zzehBx3j0oP/i1WKGraSHS/w29ms4vfisFW bteUAsgh9aG8GCp/kigjmdMbWMdCRQfXp4D+o+SSr2DcM0q2iZzXV2WTeQ6YPAJM Fn431nuPn37ULd9PXdEhgiTDfDmVpvZrHeIQpDxC/TccRj4hkbxkMn6+s5WGkJLR DAr3h2mjKgulKZ4Wlj30rOxTDO9kVqTTIxjZXhbmMxepgMihSpvRGMXbKjxVHDSe NdCoIlfjhu6trr9d39b3POQVDCtrr82WvgrlfrhZZW6YXq7dIb3hhM1RldHCM+a7 mnNDMoVDCEjLM7WLkgoOzsX4j+MyCbrsBY9DV9Zs7MtntWGcD+oH0M+ZLjrtlPef vebi+yBh/JH9fyrOiusSzbRaimy5o/NO/tYFgEAh/zk6GhwJwBYBvM1nexnfSHhv LMY+nSrgZYdN9qHurwjaBmAAmp8u0XZIz/MLQA4WpoqqoAcV2X3gtMcQMdL+nio5 sUlE60/BcXjHqp/gt3MblxZy2WVzklCuqprOSYxhPwFDx7i9SKb9erSyzEkmzQDP UU+8Bory8egR537GaxM+izq9LQ3HLpWnyGPXSGx1s0vzNpZTsYC49eFK44vJRtLK QOlFG1VAupFP5S7kDneXJ8KoWcOwG3OccPfPTvyaC8SIezjXrKDgISV2mHOghYlk uNYO2fcyBoUX9jG3dUy8 =FP4V -----END PGP SIGNATURE----- Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC platform updates from Olof Johansson: "Updates for new platform support: - New platform: Tango4 from Sigma Designs. - Broadcom BCM2836 (Raspberry Pi 2 SoC) - Enable cpufreq on Freescale i.MX7D - Rockchip: SMP support for rk3036, general support for rk3228 - SMP support on Broadcom Kona and NSP - Cleanups for OMAP removing legacy IOMMU data + a bunch of misc fixes and tweaks for various platforms" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits) ARM: tango: Fix UP build issues ARM: tango: pass ARM arch level for smc.S ARM: bcm2835: Add Kconfig support for bcm2836 ARM: OMAP2+: Add support for dm814x and dra62x usb ARM: OMAP2+: Add mmc hwmod entries for dm814x ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx ARM: OMAP2+: Fix SoC detection for dra62x j5-eco ARM: tango4: Initial platform support ARM: bcm2835: Add a compat string for bcm2836 machine probe dt-bindings: Add root properties for Raspberry Pi 2 ARM: imx: select SRC for i.MX7 ARM: uniphier: select PINCTRL ARM: OMAP2+: Remove device creation for omap-pcm-audio ARM: OMAP1: Remove device creation for omap-pcm-audio ARM: rockchip: enable support for RK3228 SoCs ARM: rockchip: use const and __initconst for rk3036 smp_operations ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER ARM: BCM: Add SMP support for Broadcom 4708 ARM: BCM: Add SMP support for Broadcom NSP ARM: BCM: Clean up SMP support for Broadcom Kona ... |
|
|
Linus Torvalds
|
5083c54264 |
ARM: SoC cleanups for v4.5
A smallish number of general cleanup commits this release cycle. Some of these are minor tweaks: - shmobile change of binding for their GIC (using arm,pl390 now) - ARCH_RENESAS introduction - Misc other renesas updates There's also a couple of treewide commits from Masahiro Yamada cleaning up const/__initconst for SMP operation structs and a switch to using "depends on" instead of if-constructs on most of the Kconfig platform targets. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJWnrTOAAoJEIwa5zzehBx3khsQAKCH1YZfI6AcY0+4z2Kmn/vK 7M86Fnmfa13ju+Iub5YuVsVFVAZ/TGTEVWoiUBMEb73IO0D5Jdl97BhJqV8Kv9Uy jz6PZGXDMJjjkts6N0ehYyu+8WbRvxtVbMNqVD/CO6CH1096UVnxgRz9uTmgJ9Z7 81EDJH4QPPg/zZR/GNV/STf4FKjlcAAN7Vo+5+m12RIptZXXkbGSL3Y6NZAyFlVB JNK5jFcabhD08DsCKa4YzbuubiQO5qiXdoxX+u/OyQWjupxM9YE5gAcna9o4V3FY Y6KnCPcy0XHCkIYk26MITXghr7UFLq9LdD2+s5Ab4HP1XZukw4TUUKd3gwCjCY2h 8RPIfvM7cJmiU3flY56A076Pg+Y35gfMQr+VDe2gMzWtrgCONWma+tHj2JSnNBkv 4I615hysQ46rzgsbpnI/yOQoXTlQH0qsNPjOlsXuRIlC4feNaw2FPTtT4dqEIXjE l7/LeHuu3217/yp2w37OrtMue4C9UZCHVSnHiV6hJgjdS+9UNRWAXMUAqWApSOam 5MPdZ/93+66gSrCdJG1KUhcw4F9MGawLAe4A41Eq7gWDbiJVDcZhRczK+Q79MNKo KvoLWAED+85qS5Z8k/1Ko9NNnl4c4kNR8fAKqD5qcEes7WGLIO1F2/RfC1zMmJfk kHYcwx4sBVPsBHDsAiPN =pQaP -----END PGP SIGNATURE----- Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Olof Johansson: "A smallish number of general cleanup commits this release cycle. Some of these are minor tweaks: - shmobile change of binding for their GIC (using arm,pl390 now) - ARCH_RENESAS introduction - Misc other renesas updates There's also a couple of treewide commits from Masahiro Yamada cleaning up const/__initconst for SMP operation structs and a switch to using "depends on" instead of if-constructs on most of the Kconfig platform targets" * tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: staging: board: armadillo800eva: Use "arm,pl390" staging: board: kzm9d: Use "arm,pl390" ARM: shmobile: r8a7778 dtsi: Use "arm,pl390" for GIC ARM: shmobile: emev2 dtsi: Use "arm,pl390" for GIC ARM: shmobile: r8a7740 dtsi: Use "arm,pl390" for GIC ARM: shmobile: r7s72100 dtsi: Use "arm,pl390" for GIC ARM: use "depends on" for SoC configs instead of "if" after prompt ARM/clocksource: use automatic DT probing for ux500 PRCMU ARM: use const and __initconst for smp_operations ARM: hisi: do not export smp_operations structures ARM: mvebu: remove unused mach/gpio.h ARM: shmobile: Remove legacy mach/irqs.h ARM: shmobile: Introduce ARCH_RENESAS MAINTAINERS: Remove link to oss.renesas.com which is closed |
|
|
Linus Torvalds
|
0c582826a1 |
ARM: SoC non-urgent fixes for v4.5
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform so these
can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W+es
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
|
|
|
Geert Uytterhoeven
|
c61f30a255 |
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
On r8a7740/armadillo, actual clock rates are ca. 4% lower than reported
by /sys/kernel/debug/clk/clk_summary. Correct the extal1 frequency from
25 MHz to 24 MHz to fix this.
This matches the Armadillo-800 EVA Product Manual, which claims the main
crystal runs at 24 MHz, and the old legacy/reference board code.
Fixes:
|
|
|
Linus Torvalds
|
984065055e |
Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.5. I don't think I've missed
anything too major, I'm mostly back at work now but I'll probably get
some sleep in 5 years time.
Summary:
New drivers:
- etnaviv:
GPU driver for the 3D core on the Vivante core used in numerous
ARM boards.
Highlights:
Core:
- Atomic suspend/resume helpers
- Move the headers to using userspace friendlier types.
- Documentation updates
- Lots of struct_mutex removal.
- Bunch of DP MST fixes from AMD.
Panel:
- More DSI helpers
- Support for some new basic panels
i915:
- Basic Kabylake support
- DP link training and detect code refactoring
- fbc/psr fixes
- FIFO underrun fixes
- SDE interrupt handling fixes
- dma-buf/fence support in pageflip path.
- GPU side for MST audio support
radeon/amdgpu:
- Drop UMS support
- GPUVM/Scheduler optimisations
- Initial Powerplay support for Tonga/Fiji/CZ/ST
- ACP audio prerequisites
nouveau:
- GK20a instmem improvements
- PCIE link speed change support
msm:
- DSI support for msm8960/apq8064
tegra:
- Host1X support for Tegra210 SoC
vc4:
- 3D acceleration support
armada:
- Get rid of struct mutex
tda998x:
- Atomic modesetting support
- TMDS clock limitations
omapdrm:
- Atomic modesetting support
- improved TILER performance
rockchip:
- RK3036 VOP support
- Atomic modesetting support
- Synopsys DW MIPI DSI support
exynos:
- Runtime PM support
- of_graph binding for DP panels
- Cleanup of IPP code
- Configurable plane support
- Kernel panic fixes at release time"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (711 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/amdgpu: add missing irq.h include
drm/vmwgfx: Fix a width / pitch mismatch on framebuffer updates
drm/vmwgfx: Fix an incorrect lock check
drm: nouveau: fix nouveau_debugfs_init prototype
drm/nouveau/pci: fix check in nvkm_pcie_set_link
drm/amdgpu: validate duplicates first
drm/amdgpu: move VM page tables to the LRU end on CS v2
drm/ttm: add ttm_bo_move_to_lru_tail function v2
drm/ttm: fix adding foreign BOs to the swap LRU
drm/ttm: fix adding foreign BOs to the LRU during init v2
drm/radeon: use kobj_to_dev()
drm/amdgpu: use kobj_to_dev()
drm/amdgpu/cz: force vce clocks when sclks are forced
drm/amdgpu/cz: force uvd clocks when sclks are forced
drm/amdgpu/cz: add code to enable forcing VCE clocks
drm/amdgpu/cz: add code to enable forcing UVD clocks
drm/amdgpu: fix lost sync_to if scheduler is enabled.
drm/amd/powerplay: fix static checker warning for return meaningless value.
drm/sysfs: use kobj_to_dev()
...
|
|
|
Linus Torvalds
|
67990608c8 |
Power management and ACPI updates for v4.5-rc1
- Add a debugfs-based interface for interacting with the ACPICA's
AML debugger introduced in the previous cycle and a new user
space tool for that, fix some bugs related to the AML debugger
and clean up the code in question (Lv Zheng, Dan Carpenter,
Colin Ian King, Markus Elfring).
- Update ACPICA to upstream revision 20151218 including a number
of fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng,
Labbe Corentin, Prarit Bhargava, Colin Ian King, David E Box,
Rafael Wysocki).
In particular, the previously added erroneous support for the
_SUB object is dropped, the concatenate operator will support
all ACPI objects now, the Debug Object handling is improved,
the SuperName handling of parameters being control methods is
fixed, the ObjectType operator handling is updated to follow
ACPI 5.0A and the handling of CondRefOf and RefOf is updated
accordingly, module-level code will be executed after loading
each ACPI table now (instead of being run once after all tables
containing AML have been loaded), the Operation Region handlers
management is updated to fix some reported problems and a the
ACPICA code in the kernel is more in line with the upstream
now.
- Update the ACPI backlight driver to provide information on
whether or not it will generate key-presses for brightness
change hotkeys and update some platform drivers (dell-wmi,
thinkpad_acpi) to use that information to avoid sending double
key-events to users pace for these, add new ACPI backlight
quirks (Hans de Goede, Aaron Lu, Adrien Schildknecht).
- Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).
- Fix the handling of the list of device IDs of device objects
found in the ACPI namespace and add a helper for checking if
there is a device object for a given device ID (Lukas Wunner).
- Change the logic in the ACPI namespace scanning code to create
struct acpi_device objects for all ACPI device objects found in
the namespace even if _STA fails for them which helps to avoid
device enumeration problems on Microsoft Surface 3 (Aaron Lu).
- Add support for the APM X-Gene ACPI I2C device to the ACPI
driver for AMD SoCs (Loc Ho).
- Fix the long-standing issue with the DMA controller on Intel
SoCs where ACPI tables have no power management support for
the DMA controller itself, but it can be powered off automatically
when the last (other) device on the SoC is powered off via ACPI
and clean up the ACPI driver for Intel SoCs (acpi-lpss) after
previous attempts to fix that problem (Andy Shevchenko).
- Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
Sinan Kaya).
- Update the device properties framework for better handling of
built-in properties, add support for built-in properties to
the platform bus type, update the MFD subsystem's handling
of device properties and add support for passing default
configuration data as device properties to the intel-lpss MFD
drivers, convert the designware I2C driver to use the unified
device properties API and add a fallback mechanism for using
default built-in properties if the platform firmware fails
to provide the properties as expected by drivers (Andy Shevchenko,
Mika Westerberg, Heikki Krogerus, Andrew Morton).
- Add new Device Tree bindings to the Operating Performance Points
(OPP) framework and update the exynos4412 DT binding accordingly,
introduce debugfs support for the OPP framework (Viresh Kumar,
Bartlomiej Zolnierkiewicz).
- Migrate the mt8173 cpufreq driver to the new OPP bindings
(Pi-Cheng Chen).
- Update the cpufreq core to make the handling of governors
more efficient, especially on systems where policy objects
are shared between multiple CPUs (Viresh Kumar, Rafael Wysocki).
- Fix cpufreq governor handling on configurations with
CONFIG_HZ_PERIODIC set (Chen Yu).
- Clean up the cpufreq core code related to the boost sysfs knob
support and update the ACPI cpufreq driver accordingly (Rafael
Wysocki).
- Add a new cpufreq driver for ST platforms and corresponding
Device Tree bindings (Lee Jones).
- Update the intel_pstate driver to allow the P-state selection
algorithm used by it to depend on the CPU ID of the processor it
is running on, make it use a special P-state selection algorithm
(with an IO wait time compensation tweak) on Atom CPUs based on
the Airmont and Silvermont cores so as to reduce their energy
consumption and improve intel_pstate documentation (Philippe
Longepe, Srinivas Pandruvada).
- Update the cpufreq-dt driver to support registering cooling
devices that use the (P * V^2 * f) dynamic power draw formula
where V is the voltage, f is the frequency and P is a constant
coefficient provided by Device Tree and update the arm_big_little
cpufreq driver to use that support (Punit Agrawal).
- Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia,
Jacob Tanenbaum, Markus Elfring).
- cpuidle core tweaks related to polling and measured_us
calculation (Rik van Riel).
- Removal of modularity from a few cpuidle drivers (clps711x,
ux500, exynos) that cannot be built as modules in practice
(Paul Gortmaker).
- PM core update to prevent devices from being probed during
system suspend/resume which is generally problematic and may
lead to inconsistent behavior (Grygorii Strashko).
- Assorted updates of the PM core and related code (Julia Lawall,
Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki,
Ulf Hansson).
- PNP bus type updates (Christophe Le Roy, Heiner Kallweit).
- PCI PM code cleanups (Jarkko Nikula, Julia Lawall).
- cpupower tool updates (Jacob Tanenbaum, Thomas Renninger).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OlYA
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull oower management and ACPI updates from Rafael Wysocki:
"As far as the number of commits goes, ACPICA takes the lead this time,
followed by cpufreq and the device properties framework changes.
The most significant new feature is the debugfs-based interface to the
ACPICA's AML debugger added in the previous cycle and a new user space
tool for accessing it.
On the cpufreq front, the core is updated to handle governors more
efficiently, particularly on systems where a single cpufreq policy
object is shared between multiple CPUs, and there are quite a few
changes in drivers (intel_pstate, cpufreq-dt etc).
The device properties framework is updated to handle built-in (ie
included in the kernel itself) device properties better, among other
things by adding a fallback mechanism that will allow drivers to
provide default properties to be used in case the plaform firmware
doesn't provide the properties expected by them.
The Operating Performance Points (OPP) framework gets new DT bindings
and debugfs support.
A new cpufreq driver for ST platforms is added and the ACPI driver for
AMD SoCs will now support the APM X-Gene ACPI I2C device.
The rest is mostly fixes and cleanups all over.
Specifics:
- Add a debugfs-based interface for interacting with the ACPICA's AML
debugger introduced in the previous cycle and a new user space tool
for that, fix some bugs related to the AML debugger and clean up
the code in question (Lv Zheng, Dan Carpenter, Colin Ian King,
Markus Elfring).
- Update ACPICA to upstream revision 20151218 including a number of
fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng, Labbe
Corentin, Prarit Bhargava, Colin Ian King, David E Box, Rafael
Wysocki).
In particular, the previously added erroneous support for the _SUB
object is dropped, the concatenate operator will support all ACPI
objects now, the Debug Object handling is improved, the SuperName
handling of parameters being control methods is fixed, the
ObjectType operator handling is updated to follow ACPI 5.0A and the
handling of CondRefOf and RefOf is updated accordingly, module-
level code will be executed after loading each ACPI table now
(instead of being run once after all tables containing AML have
been loaded), the Operation Region handlers management is updated
to fix some reported problems and a the ACPICA code in the kernel
is more in line with the upstream now.
- Update the ACPI backlight driver to provide information on whether
or not it will generate key-presses for brightness change hotkeys
and update some platform drivers (dell-wmi, thinkpad_acpi) to use
that information to avoid sending double key-events to users pace
for these, add new ACPI backlight quirks (Hans de Goede, Aaron Lu,
Adrien Schildknecht).
- Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).
- Fix the handling of the list of device IDs of device objects found
in the ACPI namespace and add a helper for checking if there is a
device object for a given device ID (Lukas Wunner).
- Change the logic in the ACPI namespace scanning code to create
struct acpi_device objects for all ACPI device objects found in the
namespace even if _STA fails for them which helps to avoid device
enumeration problems on Microsoft Surface 3 (Aaron Lu).
- Add support for the APM X-Gene ACPI I2C device to the ACPI driver
for AMD SoCs (Loc Ho).
- Fix the long-standing issue with the DMA controller on Intel SoCs
where ACPI tables have no power management support for the DMA
controller itself, but it can be powered off automatically when the
last (other) device on the SoC is powered off via ACPI and clean up
the ACPI driver for Intel SoCs (acpi-lpss) after previous attempts
to fix that problem (Andy Shevchenko).
- Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
Sinan Kaya).
- Update the device properties framework for better handling of
built-in properties, add support for built-in properties to the
platform bus type, update the MFD subsystem's handling of device
properties and add support for passing default configuration data
as device properties to the intel-lpss MFD drivers, convert the
designware I2C driver to use the unified device properties API and
add a fallback mechanism for using default built-in properties if
the platform firmware fails to provide the properties as expected
by drivers (Andy Shevchenko, Mika Westerberg, Heikki Krogerus,
Andrew Morton).
- Add new Device Tree bindings to the Operating Performance Points
(OPP) framework and update the exynos4412 DT binding accordingly,
introduce debugfs support for the OPP framework (Viresh Kumar,
Bartlomiej Zolnierkiewicz).
- Migrate the mt8173 cpufreq driver to the new OPP bindings (Pi-Cheng
Chen).
- Update the cpufreq core to make the handling of governors more
efficient, especially on systems where policy objects are shared
between multiple CPUs (Viresh Kumar, Rafael Wysocki).
- Fix cpufreq governor handling on configurations with
CONFIG_HZ_PERIODIC set (Chen Yu).
- Clean up the cpufreq core code related to the boost sysfs knob
support and update the ACPI cpufreq driver accordingly (Rafael
Wysocki).
- Add a new cpufreq driver for ST platforms and corresponding Device
Tree bindings (Lee Jones).
- Update the intel_pstate driver to allow the P-state selection
algorithm used by it to depend on the CPU ID of the processor it is
running on, make it use a special P-state selection algorithm (with
an IO wait time compensation tweak) on Atom CPUs based on the
Airmont and Silvermont cores so as to reduce their energy
consumption and improve intel_pstate documentation (Philippe
Longepe, Srinivas Pandruvada).
- Update the cpufreq-dt driver to support registering cooling devices
that use the (P * V^2 * f) dynamic power draw formula where V is
the voltage, f is the frequency and P is a constant coefficient
provided by Device Tree and update the arm_big_little cpufreq
driver to use that support (Punit Agrawal).
- Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia, Jacob
Tanenbaum, Markus Elfring).
- cpuidle core tweaks related to polling and measured_us calculation
(Rik van Riel).
- Removal of modularity from a few cpuidle drivers (clps711x, ux500,
exynos) that cannot be built as modules in practice (Paul
Gortmaker).
- PM core update to prevent devices from being probed during system
suspend/resume which is generally problematic and may lead to
inconsistent behavior (Grygorii Strashko).
- Assorted updates of the PM core and related code (Julia Lawall,
Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki, Ulf
Hansson).
- PNP bus type updates (Christophe Le Roy, Heiner Kallweit).
- PCI PM code cleanups (Jarkko Nikula, Julia Lawall).
- cpupower tool updates (Jacob Tanenbaum, Thomas Renninger)"
* tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (177 commits)
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
PM / OPP: Use snprintf() instead of sprintf()
Documentation: cpufreq: intel_pstate: enhance documentation
ACPI, PCI, irq: remove redundant check for null string pointer
ACPI / video: driver must be registered before checking for keypresses
cpufreq-dt: fix handling regulator_get_voltage() result
cpufreq: governor: Fix negative idle_time when configured with CONFIG_HZ_PERIODIC
PM / sleep: Add support for read-only sysfs attributes
ACPI: Fix white space in a structure definition
ACPI / SBS: fix inconsistent indenting inside if statement
PNP: respect PNP_DRIVER_RES_DO_NOT_CHANGE when detaching
ACPI / PNP: constify device IDs
ACPI / PCI: Simplify acpi_penalize_isa_irq()
...
|
|
|
Linus Torvalds
|
01e9d22638 |
Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- UEFI boot and runtime services support for ARM from Ard Biesheuvel
and Roy Franz.
- DT compatibility with old atags booting protocol for Nokia N900
devices from Ivaylo Dimitrov.
- PSCI firmware interface using new arm-smc calling convention from
Jens Wiklander.
- Runtime patching for udiv/sdiv instructions for ARMv7 CPUs that
support these instructions from Nicolas Pitre.
- L2x0 cache updates from Dirk B and Linus Walleij.
- Randconfig fixes from Arnd Bergmann.
- ARMv7M (nommu) updates from Ezequiel Garcia
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (34 commits)
ARM: 8481/2: drivers: psci: replace psci firmware calls
ARM: 8480/2: arm64: add implementation for arm-smccc
ARM: 8479/2: add implementation for arm-smccc
ARM: 8478/2: arm/arm64: add arm-smccc
ARM: 8494/1: mm: Enable PXN when running non-LPAE kernel on LPAE processor
ARM: 8496/1: OMAP: RX51: save ATAGS data in the early boot stage
ARM: 8495/1: ATAGS: move save_atags() to arch/arm/include/asm/setup.h
ARM: 8452/3: PJ4: make coprocessor access sequences buildable in Thumb2 mode
ARM: 8482/1: l2x0: make it possible to disable outer sync from DT
ARM: 8488/1: Make IPI_CPU_BACKTRACE a "non-secure" SGI
ARM: 8487/1: Remove IPI_CALL_FUNC_SINGLE
ARM: 8485/1: cpuidle: remove cpu parameter from the cpuidle_ops suspend hook
ARM: 8484/1: Documentation: l2c2x0: Mention separate controllers explicitly
ARM: 8483/1: Documentation: l2c: Rename l2cc to l2c2x0
ARM: 8477/1: runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()
ARM: 8476/1: VDSO: use PTR_ERR_OR_ZERO for vma check
ARM: 8453/2: proc-v7.S: don't locate temporary stack space in .text section
ARM: add UEFI stub support
ARM: wire up UEFI init and runtime support
ARM: only consider memblocks with NOMAP cleared for linear mapping
...
|
|
|
Russell King
|
6660800fb7 | Merge branch 'devel-stable' into for-linus | |
|
Rafael J. Wysocki
|
7f4a3702bd |
Merge branch 'pm-opp'
* pm-opp:
PM / OPP: Use snprintf() instead of sprintf()
PM / OPP: Set cpu_dev->id in cpumask first
PM / OPP: Fix parsing of opp-microvolt and opp-microamp properties
PM / OPP: Parse 'opp-<prop>-<name>' bindings
PM / OPP: Parse 'opp-supported-hw' binding
PM / OPP: Add missing doc comments
ARM: dts: exynos4412: Rename OPP nodes as opp@<opp-hz>
PM / OPP: Rename OPP nodes as opp@<opp-hz>
PM / OPP: Remove 'operating-points-names' binding
PM / OPP: Add {opp-microvolt|opp-microamp}-<name> binding
PM / OPP: Add "opp-supported-hw" binding
PM / OPP: Add debugfs support
|
|
|
Mauro Carvalho Chehab
|
c3152592e7 |
Merge branch 'patchwork' into v4l_for_linus
* patchwork: (204 commits) [media] rc: sunxi-cir: Initialize the spinlock properly [media] rtl2832: do not filter out slave TS null packets [media] rtl2832: print reg number on error case [media] rtl28xxu: return demod reg page from driver cache [media] coda: enable MPEG-2 ES decoding [media] coda: don't start streaming without queued buffers [media] coda: hook up vidioc_prepare_buf [media] coda: relax coda_jpeg_check_buffer for trailing bytes [media] coda: make to_coda_video_device static [media] s5p-mfc: remove volatile attribute from MFC register addresses [media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void [media] s5p-mfc: use spinlock to protect MFC context [media] s5p-mfc: remove unnecessary callbacks [media] s5p-mfc: make queue cleanup code common [media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx [media] s5p-mfc: constify s5p_mfc_codec_ops structures [media] au8522: Avoid memory leak for device config data [media] ir-lirc-codec.c: don't leak lirc->drv-rbuf [media] uvcvideo: small cleanup in uvc_video_clock_update() [media] uvcvideo: Fix reading the current exposure value of UVC ... |
|
|
Arnd Bergmann
|
4dd041b6f6 |
Renesas ARM Based SoC DT Fixes for v4.5
* Add compatible property to "partitions" node As of commit |
|
|
Stanimir Varbanov
|
668f472983 |
ARM: dts: ifc6410: enable PCIe DT node for this board
Enable PCIe DT node and fill PCIe DT node with regulator, pinctrl and reset GPIO, to use the PCIe on the ifc6410 board. Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
|
|
Stanimir Varbanov
|
bcc74b0957 |
ARM: dts: apq8064: add PCIe devicetree node
Add the PCIe DT node so that it can probe and be used. Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
|
|
Linus Torvalds
|
44d8a7d5c1 |
ARM: SoC fixes for 4.4-rc
This is the final small set of ARM SoC bug fixes for linux-4.4, almost all regressions: OMAP: data corruption on the Nokia N900 flash Allwinner: Two defconfig change to get USB working again ARM Versatile: Interrupt numbers gone bad after an older bug fix Nomadik: Crashes from incorrect L2 cache settings VIA vt8500: SD/MMC support on WM8650 never worked -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIVAwUAVpA/vGCrR//JCVInAQK1NQ//fk4EYJj6JMwaB/I2hGtpUpartVtXj9tj 916+NazORGc/UBP9vG/bLWnZrKzZQdeLd2HwDT9eyHtZ+Qq8bm+No312l10EATkS EAZKy4oy0HH5BD8yE5xM+CQn9fxh8GcmGJ/hKacpJnY2e0aaGgp9iHiPWH8kRmO4 kBbUWsbfGjxzfM+a/9XGrzcTWZLSOu6VGtxvdp2rGy+Un8AWVc6FQz48xsFXWivB 5JHp0qTnyUebSNbsxq05BDorybDuNSho5d3r94H85WwfbdybCxuFYedTZ1r3vCh9 rWDI8R2vb3uotzYYjigRwyYqggUz6TewWqwnyeyGsMHOCEU/q/2n2ASLhdxKl2x8 UZ+kKDhRiraaxnsNh/apVy4yvs7KmsUM6DgxzvXW3uyrrLrjJyGHKY5doHt5Z5mJ ErhOW024skA8GNiWObmNiKzUdKEbO4e7ReFgwbLbA8W6ACVVMNdL4udsmkb+nj25 +VFWOg5WVG5WJFaEoSOGze7J0+SSwu7wP0HRPmWFotslExh5HsrvkSw429sDDB0R 4OwT0Ru0vDZvGrHD+Bu6mFJO1nL2kWKVsolyben1sA+OIbm7eoHcennRUFf2sog0 yWD03DT9iz//bmWPHVntcdRTTaXYvaChPWzHxlbBxw2DCfRkzy4Tx/Ic44s2Kjuq PgQjTmNlnQ8= =Z1E0 -----END PGP SIGNATURE----- Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Arnd Bergmann: "This is the final small set of ARM SoC bug fixes for linux-4.4, almost all regressions: OMAP: - data corruption on the Nokia N900 flash Allwinner: - Two defconfig change to get USB working again ARM Versatile: - Interrupt numbers gone bad after an older bug fix Nomadik: - Crashes from incorrect L2 cache settings VIA vt8500: - SD/MMC support on WM8650 never worked" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: dts: vt8500: Add SDHC node to DTS file for WM8650 ARM: Fix broken USB support in multi_v7_defconfig for sunxi devices ARM: versatile: fix MMC/SD interrupt assignment ARM: nomadik: set latencies to 8 cycles ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption ARM: Fix broken USB support in sunxi_defconfig |
|
|
Linus Walleij
|
07ebfa59b9 |
ARM: versatile: add the syscon LEDs to the DT
The device tree version of Versatile AP/PB never had LED support so we are missing LEDs from our hardware boards. Add this as syscon LEDs like we did for Integrator and Juno. We need to spawn devices in the syscon with "simple-mfd" for this to work. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Arnd Bergmann
|
3c81e4e60a |
Merge tag 'meson-for-4.5/dts' of https://github.com/carlocaione/linux-meson into next/dt
Merge "Amlogic DT changes for 4.5" from Carlo Caione: This pull request includes the Amlogic Meson8b DTS changes for v4.5 * tag 'meson-for-4.5/dts' of https://github.com/carlocaione/linux-meson: ARM: dts: meson8b: Add watchdog node Documentation: watchdog: Add new bindings for meson8b ARM: meson: Add status LED for Odroid-C1 |
|
|
Roman Volkov
|
03b9ee45bc |
dts: vt8500: Fix errors in SDHC node for WM8505
According to datasheet, the registers space of SDHC controller is 1Kb, not '0x1000', the correct value should be '0x400'. Bracket interrupt numbers individually per recommendations. Signed-off-by: Roman Volkov <rvolkov@v1ros.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Roman Volkov
|
0f090bf14e |
dts: vt8500: Add SDHC node to DTS file for WM8650
Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver is already in the kernel, this node enables the controller support for WM8650 Signed-off-by: Roman Volkov <rvolkov@v1ros.org> Reviewed-by: Alexey Charkov <alchark@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Linus Walleij
|
20f12758c9 |
ARM: versatile: fix MMC/SD interrupt assignment
Commit |
|
|
Linus Walleij
|
a461a3ecfc |
ARM: nomadik: set latencies to 8 cycles
The Nomadik has sporadic crashes because of these latencies, setting them to max makes the platform work nicely, so use this values for now. These latencies were set to 2 since the Nomadik platform was merged, but I suspect they never took effect until the right size and associativity for the cache was specified in the device tree and that is why the crash comes now. Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net> |
|
|
Shawn Guo
|
9962b3d4f0 |
ARM: dts: imx6q: clean up unused ipu2grp
The pinctrl group ipu2grp is a leftover from the previous iomuxc DT cleanup. It's not used by anyone now. More importantly, it's getting in the way of saving the unnecessary pinfunc container node from the board dts files that include imx6q.dtsi. Let's clean it up. Signed-off-by: Shawn Guo <shawnguo@kernel.org> Tested-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Olof Johansson <olof@lixom.net> |
|
|
Geert Uytterhoeven
|
8bc403b78f |
ARM: dts: silk: Add compatible property to "partitions" node
As of commit
|
|
|
Geert Uytterhoeven
|
e5e6f9b489 |
ARM: dts: gose: Add compatible property to "partitions" node
As of commit
|
|
|
Geert Uytterhoeven
|
947ef62841 |
ARM: dts: porter: Add compatible property to "partitions" node
As of commit
|
|
|
Geert Uytterhoeven
|
f6531bb508 |
ARM: dts: koelsch: Add compatible property to "partitions" node
As of commit
|
|
|
Geert Uytterhoeven
|
b88ddbdd36 |
ARM: dts: lager: Add compatible property to "partitions" node
As of commit
|
|
|
Geert Uytterhoeven
|
b66c1ebae1 |
ARM: dts: bockw: Add compatible property to "partitions" node
As of commit
|
|
|
Russell King
|
06312f44ad |
Merge tag 'arm32-efi-for-v4.5' of git://git.linaro.org/people/ard.biesheuvel/linux-arm into devel-stable
This implements UEFI kernel support for 32-bit ARM, based on the existing
arm64 support and existing generic early ioremap support. It is based on
commit
|
|
|
Carlo Caione
|
e9c478a93c |
ARM: dts: meson8b: Add watchdog node
With this patch we add the watchdog node in the meson8b DTS file. Signed-off-by: Carlo Caione <carlo@endlessm.com> |
|
|
Edward Cragg
|
c16d1fdb4e |
ARM: meson: Add status LED for Odroid-C1
Add the blue status LED to the Hardkernel Odroid C1 board DTS. Signed-off-by: <edward.cragg@codethink.co.uk> Signed-off-by: Carlo Caione <carlo@endlessm.com> |
|
|
Arnd Bergmann
|
d731afa460 |
Samsung DeviceTree updates and improvements for 4.5
1. eMMC/SDIO minor fixes usage of bindings on Snow and Peach
Chromebooks.
2. Remove FIMD from Odroid XU3-family because on XU3 it cannot be used
yet and on XU3-Lite and XU4 it is not supported.
3. Remove deprecated since June 2013 samsung,exynos5-hdmi.
4. Add support for Pseudo Random Generator on Exynos4 (Trats2 for now).
This depends on new SSS clock.
5. Add rotator nodes for Exynos4 and Exynos5.
6. Switch DWC3_1 on Odroid XU3 and XU3-Lite to peripheral mode because
now it cannot be used as OTG.
7. Cleanup the G2D usage on Exynos4 and add it to a proper domain
in case of Exynos4210.
8. Put MDMA1 in proper domain on Exynos4210 as well.
9. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LMzD
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Samsung DeviceTree updates and improvements for 4.5" from Krzysztof Kozlowski:
1. eMMC/SDIO minor fixes usage of bindings on Snow and Peach
Chromebooks.
2. Remove FIMD from Odroid XU3-family because on XU3 it cannot be used
yet and on XU3-Lite and XU4 it is not supported.
3. Remove deprecated since June 2013 samsung,exynos5-hdmi.
4. Add support for Pseudo Random Generator on Exynos4 (Trats2 for now).
This depends on new SSS clock.
5. Add rotator nodes for Exynos4 and Exynos5.
6. Switch DWC3_1 on Odroid XU3 and XU3-Lite to peripheral mode because
now it cannot be used as OTG.
7. Cleanup the G2D usage on Exynos4 and add it to a proper domain
in case of Exynos4210.
8. Put MDMA1 in proper domain on Exynos4210 as well.
9. Minor cleanups.
* tag 'samsung-dt-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (21 commits)
ARM: dts: Unify G2D device node with other devices on exynos4
ARM: dts: Add power domain to G2D device on exynos4210
ARM: dts: MDMA1 device belongs to LCD0 power domain on exynos4210
ARM: dts: Remove unneeded GPIO include in exynos4412-odroidu3
ARM: dts: exynos4210-universal_c210: Disable DMA for UARTs
ARM: dts: Use peripheral mode for dwc3_1 on exynos5422-odroidxu3
ARM: dts: Add rotator node on exynos5420
ARM: dts: Add rotator node on exynos5250
ARM: dts: Fix power domain for sysmmu-rotator device on exynos4
ARM: dts: Add rotator nodes on exynos4
ARM: dts: Enable PRNG module on exynos4412-trats2
ARM: dts: Add PRNG module for exynos4
dt-bindings: remove deprecated compatible string from exynos-hdmi
ARM: dts: Remove fimd node from exynos5422-odroidxu3-common
ARM: dts: Mark eMMC as non-removable in exynos5250-snow-common
ARM: dts: Remove broken-cd from eMMC node in exynos5420-peach-pi
ARM: dts: Remove broken-cd from eMMC node in exynos5800-peach-pi
ARM: dts: Mark SDIO as non-removable in exynos5250-snow-common
ARM: dts: Mark SDIO as non-removable in exynos5420-peach-pit
ARM: dts: Mark SDIO as non-removable in exynos5800-peach-pi
...
|
|
|
Masahiro Yamada
|
4e333015ed |
ARM: dts: uniphier: fix a typo in comment block
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Eric Anholt
|
ddc5c39af4 |
ARM: bcm2835: Add the auxiliary clocks to the device tree.
These will be used for enabling UART1, SPI1, and SPI2. Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Eric Anholt
|
80534f095f |
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
The Pi 2 B ends up like a Pi 1 B+, with the same peripherals and pinout, but the CPU and memory layout changed to use the 2836. Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Eric Anholt
|
4b8c3907c3 |
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
For Raspberry Pi 2, we want to use the same general pin assignment bits, but need to use bcm2836.dtsi for the CPU instead. Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Eric Anholt
|
548c3a39e0 |
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
The set of peripherals remained constant across bcm2835 (Raspberry Pi 1) and bcm2836 (Raspberry Pi 2), but the CPU was swapped out. Split the files so that we can include just peripheral setup in 2836. Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Linus Walleij
|
ef2a270592 |
ARM: realview: set up cache correctly on the PB11MPCore
The L2 cache comes up in a "safe mode" on the PB11MPCore, as it has several issues. This sets it up properly with the right size and associativity, also requiring the outer sync to be disabled for the machine to boot properly. Cc: Russell King <linux@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
|
|
Arnd Bergmann
|
f0dba77620 |
EDMA device-tree updates including move to
new EDMA bindings and EDMA support for MMC/SD and SPI. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.10 (GNU/Linux) iQIcBAABAgAGBQJWe9hFAAoJEGFBu2jqvgRNUPEP/jX7Vsqj1nYSZIT9uhTL2yhG u+TVPqAt90LDl0ikfc6GoUS0DOtNvO3LLWIocgcrn29ltEWJUmhm3E3p0KLuY3Kx WEkvL/qc+9DtLXPPwOz2Svhc4yhmW9wxw4vseqUplJJyBGmBMFTh4gUr8gej72uF +gQRVRxmENeIoPHzqFWnf34HJvzyVORxbzOrcRemfhYYfs+ES5KU0LXLYh1TNC1a 87gKv/EsyhKVn5JEAQlRbkMqf+r+JwwcFWnwB0/OFP65S6iy0v+xzAjYgRe3W5Y0 ylTdMUKf8JNassU7ig1Lh509OqNTE0a7SuIZG2P56Q58XgepyDSreiGxi0lXFnqF Cfd+05xAY4wn2q9d6mF4S4vclcTzVC7z22z68zCdtDfhMTCrLuSI9SsXWMkTZmUe E7lSk3rGfN63dN6BGIkciqWIKgGeEPOzKOHD8kuMOYHehwCOudVU3TZ346Y+DV1e X6haDjbxIwjVXy3ILF0mgty4poMmvW/eeZNIB4k315IACUGDg53PXrCdEagLEAEl 1vDym6NX28apSPPNaBX6adniK59SsyrplSu1HqcW7i/UZ67bWjZR/0cYCRWD+hKX v44vEvNrUFUF+Fjqied1lxDNtH9QdTFt1j+gjrhqJrmya4L9MCwNZ1PacunmfPDX eFpZbRrD+0kAGiqlBEem =dKhP -----END PGP SIGNATURE----- Merge tag 'davinci-for-v4.5/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt Merge "DaVinci device-tree updates for v4.5" from Sekhar Nori: EDMA device-tree updates including move to new EDMA bindings and EDMA support for MMC/SD and SPI. * tag 'davinci-for-v4.5/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: ARM: DTS: da850: Enable DMA for SPI1 ARM: DTS: da850: Add node for mmc1 ARM: DTS: da850: Enable DMA use for MMC0 ARM: DTS: da850: Enable eDMA1 ARM: DTS: da850: Use the new DT bindings for the eDMA3 ARM: DTS: da850: fix edma0 reg space |
|
|
Arnd Bergmann
|
d4e68fa37f |
Add minimal device tree support for dra62x also known j5eco. It is
related to dm814x, just the clocks are a bit different and it has a different set of integrated devices. And let's get some basic dm814x and dra62x devices working as many of the devices are like on am33xx:: - pinctrl using the pinctrl defines as for am33xx - Updated EDMA bindings with support for using exma_xbar - MMC support for dm814x-evm, t410 and dra62x-j5eco-evm - USB support for dm814x-evm, t410 and dra62x-j5eco-evm This branch depends on an earlier omap-for-v4.5/81xx-fixes-signed branch that has dm814x dts fixes interlaced with SoC related fixes to keep things booting. The interlaced SoC and dts fixes were needed because of issues with the device tree defined clocks that just happened to work on bootloader timings for t410 earlier. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJWeewGAAoJEBvUPslcq6Vz+5UQAJDZH9+kELrI1i1ymWg50q2+ HdnswijaQVuX1ZZeyarytvMT00s6bkouaGTLYrPGlifuJuBAAZ3PewZ4FVgIkA4A V4QAl3+vZ0wU+TjwWLlODXwd20xAeGY5LmhLkaHheP8Dbnd1OLm2BxJlps+zK3WJ a9Wv0rcwJuJt9dBGdELDcj04SlHd6oOmy+bHeoUi0VBcb+ZJD8+WaWQB1qkvae46 IitA74nDLY0Ejezf3lJ8Bu+I1NKv5tGg//SEJTZQfaSFxGoYbfcHkOKrBP8MAM8U IQZHxz0izeKaAyra7qrqiHox4GVJpKFVkvHrDlox9GDSUKxP0cRpahLEqjUF1VMm FYE2dh/JjWFhPaGMVIQIiVQNND6NZlycBc1fcEKuT+2tXjqALQ1qDZwb6S44q5/r 1QL+pBIZVMl5YaTpt/yh7COhpMtKbofamzJkzUTVwx6ao/a1uK2G+K83ZB9wkPkw YUBL68oD8EN+fSnZMVlFQkwJGgmoMzaFuqLJMjV0RQWTmzHH43Nyg76muMCIiKwf Xu4ZdNUS7VkHYdjVJXQcXU4igLejj6Q/Qmvw1M+LxsyDH+I4WRgWgYB11T45f0Lf eafwSkAayq7dBzuXJ4kOuK5sR9LOYA7Le9XRvu9f8KOY2aKWoZiVB2KPCz7BaoNs BZH5tf0C7D5mXQz8sXik =W/MF -----END PGP SIGNATURE----- Merge tag 'omap-for-v4.5/81xx-dts-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Pull "reworked dts changes for ti81xx devices and minimal dra62x j5ec-evm support" from Tony Lindgren: Add minimal device tree support for dra62x also known j5eco. It is related to dm814x, just the clocks are a bit different and it has a different set of integrated devices. And let's get some basic dm814x and dra62x devices working as many of the devices are like on am33xx:: - pinctrl using the pinctrl defines as for am33xx - Updated EDMA bindings with support for using exma_xbar - MMC support for dm814x-evm, t410 and dra62x-j5eco-evm - USB support for dm814x-evm, t410 and dra62x-j5eco-evm This branch depends on an earlier omap-for-v4.5/81xx-fixes-signed branch that has dm814x dts fixes interlaced with SoC related fixes to keep things booting. The interlaced SoC and dts fixes were needed because of issues with the device tree defined clocks that just happened to work on bootloader timings for t410 earlier. * tag 'omap-for-v4.5/81xx-dts-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits) ARM: dts: Add usb support for j5-eco evm ARM: dts: Add usb support for hp t410 ARM: dts: Add usb support for dm814x-evm ARM: dts: Add usb support for dm814x and dra62x ARM: dts: Enable emmc on hp t410 ARM: dts: Add mmc support for dra62x j5-eco evm ARM: dts: Add mmc support for dm8148-evm ARM: dts: Add mmc device entries for dm814x ARM: dts: Update edma bindings on dm814x to use edma_xbar ARM: dts: Add pinctrl macros for dm814x ARM: dts: Add minimal dra62x j5-eco evm support ARM: dts: Add basic support for dra62x j5-eco SoC ARM: OMAP2+: Remove useless check for legacy booting for dm814x ARM: OMAP2+: Enable GPIO for dm814x ARM: dts: Fix dm814x pinctrl address and mask ARM: dts: Fix dm8148 control modules ranges ARM: OMAP2+: Fix timer entries for dm814x ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting ARM: OMAP2+: Add DPPLS clock manager for dm814x clk: ti: Add few dm814x clock aliases ... |