* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.
The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: Pavel Mateja <pavel@netsafe.cz>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.
Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.
Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing VRRP v2 using macvlan several problems were
discovered. VRRP is weird in that all routers participating
in a redundant group use the same virtual MAC address.
Macvlan is a natural driver to use for this but it doesn't
work. The problem is that packets with a macvlan device's
source address are not received.
The problem is actually a regression that date back almost 2 years now.
The original problems started with:
commit 618e1b7482
Author: Arnd Bergmann <arnd@arndb.de>
Date: Thu Nov 26 06:07:10 2009 +0000
macvlan: implement bridge, VEPA and private mode
This patches restores the original 2.6.32 behavior. Allowing multicast
packets received with the VRRP source address to be received.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.121.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During shutdown, it is impossible to reliably disable the timer and
reset_task threads. Each thread can schedule the other, which leads to
shutdown code that chases its tail.
To fix the problem, this patch removes the ability of tg3_reset_task to
schedule a new timer thread. To support this change, tg3_timer no
longer terminates itself, but rather goes into a polling mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for multiple threads in the tg3 driver to each attempt to
schedule a run of tg3_reset_task(). The multiple tg3_reset_task
executions could all wind up on the same queue (and execute serially) or
wind up on the queues of another processor (which could execute in
parallel). Either scenario is not what was truly desired.
This patch adds a new flag, TG3_FLAG_RESET_TASK_PENDING, and uses it to
determine whether or not to schedule another run of tg3_reset_task().
With the new flag comes two new functions to facilitate scheduling and
descheduling of tg3_reset_task().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to attempt to obtain the PCI function number from
the device rather than accept the number handed by the kernel. In
pass-through scenarios, the function number handed by the kernel may not
reflect the true function of the device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where the irq error cleanup path did not free all
the resources it allocated.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Li <benli@broadcom.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the error recovery resource unwind path, it is possible for the
driver to attempt to unmap a fragment that hadn't been mapped. This
patch fixes the problem by correcting the "last" parameter supplied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 4k tx bd segmentation code had a bug in the error cleanup path.
If the driver did not map all the physical fragments, the abort path
would wind up advancing the producer index beyond the point where the
setup code stopped. This would ultimately turn into a tx recovery error
where the driver would expect the skb pointer to be set when it isn't.
This patch fixes the problem, and then makes the code a little easier to
understand.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
APE mutex register blocks are shared by all ports of multiport devices.
For some mutexing purposes, each function is assigned their own
register. For other cases, each function is assigned its own request
and grant bits of a single register. For the latter cases, the tg3
driver is incorrectly allowing each function to use the same set of
grant / request bits. This patch fixes the code so that each function
uses the appropriate bitset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
be2net: Add detect UE feature for Lancer
be2net: Prevent CQ full condition for Lancer
be2net: Fix disabling multicast promiscous mode
be2net: Fix endian issue in RX filter command
af_packet: de-inline some helper functions
MAINTAINERS: Add can-gw include to maintained files
net: Add back alignment for size for __alloc_skb
net: add missing bh_unlock_sock() calls
l2tp: fix race in l2tp_recv_dequeue()
ixgbevf: Update release version
ixgbe: DCB, return max for IEEE traffic classes
ixgbe: fix reading of the buffer returned by the firmware
ixgbe: Fix compiler warnings
ixgbe: fix smatch splat due to missing NULL check
ixgbe: fix disabling of Tx laser at probe
ixgbe: Fix link issues caused by a reset while interface is down
igb: Fix for I347AT4 PHY cable length unit detection
e100: make sure vlan support isn't advertised on old adapters
e1000e: demote a debugging WARN to a debug log message
net: fix typo in drivers/net/ethernet/xilinx/ll_temac_main.c
...
Add code to detect UE in case of Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to HW that the CQ is cleaned up before posting new RX buffers.
This prevents the HW to go into CQ full error condition.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32() for mcast_num field in RX filter command as this
field is of type u32.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning the max traffic classes on get requests simplifies
user space configurations because applications will know
explicitly how many traffic classes can be used.
Typical switch implementations use 2 or 3 traffic classes
so this not seen often today. And user space can learn
the number of traffic classes by return codes but this
allows user space to configure ixgbe correctly at the
start.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes some issues found in the buffer read portion of
ixgbe_host_interface_command()
- use `bi` as the buffer index counter instead of `i`
- add conversion to native cpu byte ordering on register read
- fix conversion from bytes to dword
- use dword_len instead of buf_len when reading the register
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wrap SR-IOV specific functions in CONFIG_PCI_IOV to avoid compiler
warnings.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_ieee_ets and ixgbe_ieee_pfc are intialized at
the same time. Do a check for both before configuring
IEEE802.1Qaz. Also max_frame was causing a sparse
warning resolved here as well.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
register_netdev() calls ndo_set_features() which may result in HW reset
which in turn will bring the laser back up.
This patch moves ixgbe_laser_tx_disable() below register_netdev()
in ixgbe_probe() to make sure laser is shut off on load.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Interface fails to obtain link on 82599 SFP in the following scenario:
1. Set advertised speed to GB:
ethtool -s eth0 advertise 0x20
2. Bring interface down
ip link set eth0 down
3. Issue any command that leads to a reset:
ethtool -t eth0
4. Bring link back up:
ip link set eth0 up
Following patch makes sure that the driver flaps the Tx laser every time
ixgbe_start_hw() is called, and not only when the speed is set.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY cable length unit detection was not using the correct
the correct PHY data variable for I347AT4.
Signed-off-by: Tomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e100 parts don't support vlan offload but they generally do
allow use of vlans in higher software layers via the 8021q module.
That said, there are a couple of really old revisions of e100
hardware that don't even allow the longer frame sizes
required for vlan use with standard MTU.
Use the VLAN_CHALLENGED flag to prevent vlan binding to these
devices.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: David Lamparter <equinox@diac24.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This debugging message was recently added but it does not need to be as
alarming as a WARN.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Says Andrew:
"60 patches. That's good enough for -rc1 I guess. I have quite a lot
of detritus to be rechecked, work through maintainers, etc.
- most of the remains of MM
- rtc
- various misc
- cgroups
- memcg
- cpusets
- procfs
- ipc
- rapidio
- sysctl
- pps
- w1
- drivers/misc
- aio"
* akpm: (60 commits)
memcg: replace ss->id_lock with a rwlock
aio: allocate kiocbs in batches
drivers/misc/vmw_balloon.c: fix typo in code comment
drivers/misc/vmw_balloon.c: determine page allocation flag can_sleep outside loop
w1: disable irqs in critical section
drivers/w1/w1_int.c: multiple masters used same init_name
drivers/power/ds2780_battery.c: fix deadlock upon insertion and removal
drivers/power/ds2780_battery.c: add a nolock function to w1 interface
drivers/power/ds2780_battery.c: create central point for calling w1 interface
w1: ds2760 and ds2780, use ida for id and ida_simple_get() to get it
pps gpio client: add missing dependency
pps: new client driver using GPIO
pps: default echo function
include/linux/dma-mapping.h: add dma_zalloc_coherent()
sysctl: make CONFIG_SYSCTL_SYSCALL default to n
sysctl: add support for poll()
RapidIO: documentation update
drivers/net/rionet.c: fix ethernet address macros for LE platforms
RapidIO: fix potential null deref in rio_setup_device()
RapidIO: add mport driver for Tsi721 bridge
...
Modify Ethernet addess macros to be compatible with BE/LE platforms
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: <stable@kernel.org> [2.6.39+]
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://github.com/rustyrussell/linux:
virtio-blk: use ida to allocate disk index
virtio: Add platform bus driver for memory mapped virtio device
virtio: Dont add "config" to list for !per_vq_vector
virtio: console: wait for first console port for early console output
virtio: console: add port stats for bytes received, sent and discarded
virtio: console: make discard_port_data() use get_inbuf()
virtio: console: rename variable
virtio: console: make get_inbuf() return port->inbuf if present
virtio: console: Fix return type for get_inbuf()
virtio: console: Use wait_event_freezable instead of _interruptible
virtio: console: Ignore port name update request if name already set
virtio: console: Fix indentation
virtio: modify vring_init and vring_size to take account of the layout containing *_event_idx
virtio.h: correct comment for struct virtio_driver
virtio-net: Use virtio_config_val() for retrieving config
virtio_config: Add virtio_config_val_len()
virtio-console: Use virtio_config_val() for retrieving config
Perform "echo test" when cmd queue stuck detected, somethime it will cause
calltrace. I am not sure how to fix it yet, just remove the action now until
find a better way to handle it.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver can spam the logs with "RX: Packet dropped" messages. These drops
originate from 1. a correpted PLCP, 2. decryption errors, and 3. packet
size underruns. Condition #3 logs a separate message, thus no dropped message
is needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Continue the init process even fail to enable msi
out_iounmap is no longer used, remove it
Reported-by: werner <w.landgraf@ru.ru>
Tested-by: werner <w.landgraf@ru.ru>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 2e30168b ("libertas: terminate scan when stopping interface")
adds cleanup code to lbs_eth_stop to call cfg80211_scan_done if there's
an outstanding cfg80211_scan_request. However, it assumes that the
scan request was allocated via the cfg80211 stack. Libertas has
its own internal allocation method, kept track of with
priv->internal_scan. This doesn't set scan_req->wiphy, amongst other
things, which results in hitting a BUG() when we call cfg80211_scan_done
on the request.
This provides a function to take care of the low-level scan_req cleanup
details. We simply call that to deal with finishing up scan requests.
The bug we were hitting was:
[ 964.321495] kernel BUG at net/wireless/core.h:87!
[ 964.329970] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 964.341963] pgd = dcf80000
...
[ 964.849998] 9fe0: 00000000 beb417b8 4018e280 401e822c 60000010 00000004 00000000 00000000
[ 964.865007] [<c003104c>] (__bug+0x1c/0x28) from [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c)
[ 964.895324] [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c) from [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas])
[ 964.895324] [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas]) from [<c03002a0>] (__dev_close_many+0x94/0xc4)
[ 964.918995] [<c03002a0>] (__dev_close_many+0x94/0xc4) from [<c030037c>] (dev_close_many+0x78/0xe0)
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].
But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ce407afc10 introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.
Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.
This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message
ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Stanislaw pointed out, my patch
iwlagn: fix a race in the unmapping of the TFDs
solved only part of the problem. The race still exists for TFDs of
the host commands. Fix that too.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
Commit 9e903e0852 ("net: add skb frag size accessors") used frag_size
instead of skb_frag_size in this file.
Fixes this build error:
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit':
drivers/net/ethernet/xilinx/ll_temac_main.c:717:3: error: implicit declaration of function 'frag_size' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies virtio-net to use virtio_config_val() instead
of a 'if(virtio_has_feature()) vdev->config->get()' construct to retrieve
optional values from the config space.
Cc: Amit Shah <amit.shah@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Macintosh CS89x0 based ethernet cards use a Crystal Semiconductor (Now
Cirrus Logic) CS89x0 chip, so the mac89x0 driver should be in
drivers/net/ethernet/cirrus instead of drivers/net/ethernet/apple.
This also fixes a build problem, as the driver needs a header file from the
cirrus directory:
drivers/net/ethernet/apple/mac89x0.c:107:20: error: cs89x0.h: No such file or directory
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.
Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng Liang(lzheng@redhat.com) found a bug that if we config bonding with
arp monitor, sometimes bonding driver cannot get the speed and duplex from
its slaves, it will assume them to be 100Mb/sec and Full, please see
/proc/net/bonding/bond0.
But there is no such problem when uses miimon.
(Take igb for example)
I find that the reason is that after dev_open() in bond_enslave(),
bond_update_speed_duplex() will call igb_get_settings()
, but in that function,
it runs ethtool_cmd_speed_set(ecmd, -1); ecmd->duplex = -1;
because igb get an error value of status.
So even dev_open() is called, but the device is not really ready to get its
settings.
Maybe it is safe for us to call igb_get_settings() only after
this message shows up, that is "igb: p4p1 NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX".
So I prefer to update the speed and duplex for a slave when reseices
NETDEV_CHANGE/NETDEV_UP event.
Changelog
V2:
1 remove the "fake 100/Full" logic in bond_update_speed_duplex(),
set speed and duplex to -1 when it gets error value of speed and duplex.
2 delete the warning in bond_enslave() if bond_update_speed_duplex() returns
error.
3 make bond_info_show_slave() handle bad values of speed and duplex.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
The `#define filename' screws up the expansion of
DEFINE_DYNAMIC_DEBUG_METADATA:
drivers/net/ethernet/i825xx/3c505.c: In function 'send_pcb':
drivers/net/ethernet/i825xx/3c505.c:390: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:390: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c:436: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:435: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'start_receive':
drivers/net/ethernet/i825xx/3c505.c:557: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:557: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'receive_packet':
drivers/net/ethernet/i825xx/3c505.c:629: error: expected identifier before string constant
etc
So remove that #define and "open-code" it.
Cc: Philip Blundell <philb@gnu.org>
Cc: David Miller <davem@davemloft.net>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This 2nd batch of implicit module.h users only appeared when we
removed the unnecessary module.h from include/linux/miscdevice.h
[The 1st batch is already present in Greg's staging tree.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For some reason three #include <linux/...> are buried way
down in the file. Since the inclusion of module.h is one
of them, the inclusion comes after use of EXPORT_SYMBOL
which will cause warnings about implicit declarations.
Relocate all the headers to the top.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It only has module_param and EXPORT_SYMBOL, so now that export.h
is in scope at the same time as the recent ath5k update, we can
delete this module.h include.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were using moduleparam infrastructure, but were not
including anything for it -- which is fine when module.h is being
implicitly included in all files, but that is going away.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c
This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enable the maximum size (128) supported by the device for the shadow
vlans table, ignoring the module parameter that overrides it. This
table is only used by the IBoE control plane for setting a vlan index
into an RC/UC QP context or UD Address Handle.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch resolves two sets of race conditions.
Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the
first, as follows:
The bond_close() calls cancel_delayed_work() to cancel delayed works.
It, however, cannot cancel works that were already queued in workqueue.
The bond_open() initializes work->data, and proccess_one_work() refers
get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when
work->data has been initialized. Thus, a panic occurs.
He included a patch that converted the cancel_delayed_work calls
in bond_close to flush_delayed_work_sync, which eliminated the above
problem.
His patch is incorporated, at least in principle, into this
patch. In this patch, we use cancel_delayed_work_sync in place of
flush_delayed_work_sync, and also convert bond_uninit in addition to
bond_close.
This conversion to _sync, however, opens new races between
bond_close and three periodically executing workqueue functions:
bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon.
The race occurs because bond_close and bond_uninit are always
called with RTNL held, and these workqueue functions may acquire RTNL to
perform failover-related activities. If bond_close or bond_uninit is
waiting in cancel_delayed_work_sync, deadlock occurs.
These deadlocks are resolved by having the workqueue functions
acquire RTNL conditionally. If the rtnl_trylock() fails, the functions
reschedule and return immediately. For the cases that are attempting to
perform link failover, a delay of 1 is used; for the other cases, the
normal interval is used (as those activities are not as time critical).
Additionally, the bond_mii_monitor function now stores the delay
in a variable (mimicing the structure of activebackup_arp_mon).
Lastly, all of the above renders the kill_timers sentinel moot,
and therefore it has been removed.
Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Updated version number to 5.0.25
o Do not hold onto RESETTING_BIT for entire duration of LED/ beacon test.
Instead, just checking for RESETTING_BIT not set before sending config_led
command down to card.
o Take rtnl_lock instead of RESETTING_BIT for beacon test while sending
config_led command down to make sure interface cannot be brought up/ down.
o Allocate and free resources if interface is down before
sending the config_led command. This is to make sure config_led
command sending doesn't fail.
o Clear QLCNIC_LED_ENABLE bit if beacon/ LED test fails to start.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If promiscous mode setting fails, reset loopback mode setting in firmware.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fw reset path, we should consider any change in device state as an
ack from the other driver. When that happens, we don't have to wait for
an explicit ack.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An Extended Port Info packet is sent to each hw port during HCA init.
If it returns without error, we assume the port supports extended port
capabilities.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch updates the normal descriptor structure
to work fine on new GMAC Synopsys chips.
Normal descriptors were designed on the old MAC10/100
databook 1.91 where some bits were reserved: for example
the tx checksum insertion and rx checksum offload.
The patch maintains the back-compatibility with old
MAC devices (tested on STx7109 MAC10/100) and adds new
fields that actually new GMAC devices can use.
For example, STx7109 (MAC10/100) will pass from the platform
tx_coe = 0, enh_desc = 0, has_gmac = 0.
A platform like Loongson1B (GMAC) will pass:
tx_coe = 1, enh_desc = 0, has_gmac = 1.
Thanks to Kelvin, he enhanced the normal descriptors for
GMAC (on MIPS Loongson1B platform).
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Angus Clark <angus.clark@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a bug while checking the HW cap reg
on old MAC10/100 where this feature is not available.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for MAC Address change of VF(SR-IOV case) on the fly- First add and then
delete MAC Address to allow for 'out of pool' errors.
When MAC Addr configured from a VM, the MAC on the NIC will aleady have
the supplied MAC,so just copy the supplied MAC to the netdev structure
before returning success to the stack
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved the .sge. field's population inside be_cmd_hdr_prepare.
Populating wrb->tag0 and tag1 inside be_cmd_hdr_prepare
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FW includes the following fixes:
1. (iSCSI) Arrival of un-solicited ASYNC message causes
firmware to abort the connection with RST.
2. (FCoE) There is a probability that truncated FCoE packet on
RX path won't get detected which might lead to FW assert.
3. (iSCSI) Arrival of target-initiated NOP-IN during intense
ISCSI traffic might lead to FW assert.
4. (iSCSI) Chip hangs when in case of retransmission not aligned
to 4-bytes from the beginning of iSCSI PDU.
5. (FCoE) Arrival of packets beyond task IO size can lead to crash.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem in which the host stops receiving data after
restarting the interface. This issue is caused by combination of incorrect
data path tap closure, along with missing MAC reset.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix solves a problem of no link on 578xx-KR by retrying to link up to
four timer using the periodic function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust blink rate on 578xx to fit its clock rate.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xenbus module provides xenbus_map_ring_valloc() and
xenbus_map_ring_vfree(). Use these to map the Tx and Rx ring pages
granted by the frontend.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
If the PHY should disappear (for example, on an USB Ethernet MAC), then
the driver would leak any undelivered time stamp packets. This commit
fixes the issue by calling the appropriate functions to free any packets
left in the transmit and receive queues.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit enforces a new rule for handling the cloned packets
for transmit time stamping. These packets must not be freed using any other
function than skb_complete_tx_timestamp. This commit fixes the one and only
driver using this API.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a frame cant be transmitted, it is silently discarded.
Add a counter to report these errors to user.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HW is in multi-channel mode based on the skew/IPL, there are
4 functions per port and so not enough resources to create multiple
RX/TX rings for each function.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple TXQ support is partially broken in BE2. It is fully
supported BE3 onwards and in Lancer.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the code for VF setup/teardown done by a PF (if_create,
mac_add_config, link_status_query etc) is scattered; this patch
refactors this code into be_vf_setup() and be_vf_clear(). The
if_create/if_destroy/mac_addr_query cmds are now called after the MCCQ
is created; so these cmds are now modified to use the MCCQ instead of
MBOX.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a card is reset due to EEH error recovery or due to a suspend,
rx-mode config (promisc/mc) is not being sent to the FW. be_setup() is
called in these flows and is the best place for such config/re-config
cmds. Hence include rx-mode, vlan and flow-control config in
be_setup().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the last hardcoded base address from the au1000_eth
driver. The base address of the MACDMA unit was derived from the
platform device id; if someone registered the MACs in inverse order
both would not work.
So instead pass the base address of the DMA unit to the driver with
the other platform resource information.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: David S. Miller <davem@davemloft.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2674/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit
"7488876... dt/net: Eliminate users of of_platform_{,un}register_driver"
there are two platform drivers named "mdio-gpio" registered.
I renamed the of variant to "mdio-ofgpio".
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is down during suspend/resume, interrupts are enabled
without a registered interrupt handler, causing a storm of
unhandled interrupts until the IRQ is disabled because "nobody
cared".
Instead, check that the device is up before touching it in the
suspend/resume code.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=39112
Helped-by: Adrian Chadd <adrian@freebsd.org>
Helped-by: Mohammed Shafi <shafi.wireless@gmail.com>
Signed-off-by: Clemens Buchacher <drizzd@aon.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reporting ring sizes via ethtool -g to the virtio_net
driver.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ari got kernel panics using tg3 NIC, and bisected to 2669069aac "tg3:
enable transmit time stamping."
This is because tigon3_dma_hwbug_workaround() might alloc a new skb and
free the original. We panic when skb_tx_timestamp() is called on freed
skb.
Reported-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a hardware problem, writes to the VFTA register can
theoretically fail. Although the likelihood of this is very low.
This patch adds a shadow vfta in the adapter struct for reading
and adds new write functions for these devices to work around the problem.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the DMA Coalescing feature initialization code from
igb_reset to a new function and replaces it with a call to the new
function.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In 82580 and later devices, the alternate MAC address feature is
completely handled by the option ROM and software does not handle
it anymore. This patch changes the check_alt_mac_addr function to
exit immediately if device is 82580 or later.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update adapter identification strings to properly indicate i350 VF devices
in the VF driver. Change the driver ID string to remove 82576-specific
wording. Update copyright date.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On systems that create and delete lots of dynamic devices the
31bit linux ifindex fails to fit in the 16bit macvtap minor,
resulting in unusable macvtap devices. I have systems running
automated tests that that hit this condition in just a few days.
Use a linux idr allocator to track which mavtap minor numbers
are available and and to track the association between macvtap
minor numbers and macvtap network devices.
Remove the unnecessary unneccessary check to see if the network
device we have found is indeed a macvtap device. With macvtap
specific data structures it is impossible to find any other
kind of networking device.
Increase the macvtap minor range from 65536 to the full 20 bits
that is supported by linux device numbers. It doesn't solve the
original problem but there is no penalty for a larger minor
device range.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place macvlan_common_newlink at the end of macvtap_newlink because
failing in newlink after registering your network device is not
supported.
Move device_create into a netdevice creation notifier. The network device
notifier is the only hook that is called after the network device has been
registered with the device layer and before register_network_device returns
success.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid leaking packets in the receive queue. Add a socket destructor
that will run whenever destroy a macvtap socket.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To see if it is appropriate to enable the macvtap zero copy feature
don't test the lowerdev network device flags. Instead test the
macvtap network device flags which are a direct copy of the lowerdev
flags. This is important because nothing holds a reference to lowerdev
and on a very bad day we lowerdev could be a pointer to stale memory.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small window in macvtap_open between looking up a
networking device and calling macvtap_set_queue in which
macvtap_del_queues called from macvtap_dellink. After
calling macvtap_del_queues it is totally incorrect to
allow macvtap_set_queue to proceed so prevent success by
reporting that all of the available queues are in use.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must account in skb->truesize, the size of the fragments, not the
used part of them.
Doing this work is important to avoid unexpected OOM situations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: virtualization@lists.linux-foundation.org
CC: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x allocates a full page per fragment.
We must account in skb->truesize, the size of the fragment, not the used
part of it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the ethtool interface. The implementation is done
using the libphy helper functions.
Signed-off-by: David S. Miller <davem@davemloft.net>
control these three function declarations and
definitions with same macro CONFIG_PCI_IOV
drivers/net/ethernet/intel/igb/igb_main.c:165:
warning: ‘igb_vf_configure’ declared ‘static’ but never defined
drivers/net/ethernet/intel/igb/igb_main.c:166:
warning: ‘igb_find_enabled_vfs’ declared ‘static’ but never defined
drivers/net/ethernet/intel/igb/igb_main.c:167:
warning: ‘igb_check_vf_assignment’ declared ‘static’ but never defined
Signed-off-by: RongQing Li <roy.qing.li@gmail.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize must account for allocated memory, not the used part of
it. Doing this work is important to avoid unexpected OOM situations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jon Mason <mason@myri.com>
Acked-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igbvf allocates half a page per skb fragment. We must account
PAGE_SIZE/2 increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize must account for allocated memory, not the used part of
it. Doing this work is important to avoid unexpected OOM situations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove manual initialization in set_skb_frag, and instead
use __skb_fill_page_desc() to do the same. Patch tested
on net-next.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ethtool -e ethX" dumps EEPROM data. Patch sets EEPROM length for device.
Ethtool works alot better when the kernel believes the length is > 0.
From: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem using big mtu around 4096 bytes is you end allocating (4096
+NET_SKB_PAD + NET_IP_ALIGN + sizeof(struct skb_shared_info) bytes ->
8192 bytes : order-1 pages
It's better to limit the mtu to SKB_MAX_HEAD(NET_SKB_PAD),
to have no more than one page per skb.
Also the patch changes the netdev_alloc_skb_ip_align() done in
init_dma_desc_rings() and uses a variant allowing GFP_KERNEL allocations
allowing the driver to load even in case of memory pressure.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the STMMAC driver to support CHAINED mode of
descriptor.
STMMAC supports DMA descriptor to operate both in dual buffer(RING)
and linked-list(CHAINED) mode. In RING mode (default) each descriptor
points to two data buffer pointers whereas in CHAINED mode they point
to only one data buffer pointer.
In CHAINED mode each descriptor will have pointer to next descriptor in
the list, hence creating the explicit chaining in the descriptor itself,
whereas such explicit chaining is not possible in RING mode.
First version of this work has been done by Rayagond.
Then the patch has been reworked avoiding ifdef inside the C code.
A new header file has been added to define all the functions needed for
managing enhanced and normal descriptors.
In fact, these have to be specialized according to the ring/chain usage.
Two new C files have been also added to implement the helper routines
needed to manage: jumbo frames, chain and ring setup (i.e. desc3).
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the MMC support if it is actually available from the
HW capability register.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to set the mtu bigger than 1500
in case of normal descriptors.
This is helping some SPEAr customers.
Signed-off-by: Deepak SIKRI <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem raised on Orly ARM SMP platform
where, in case of fragmented frames, the descriptors
in the TX ring resulted broken. This was due to a missing lock
protection in the tx process.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch stops advertising 1000Base capablities if GMAC is either
configured for MII or RMII mode and on board there is a GPHY plugged on.
Without this patch if an GBit switch is connected on MII interface,
Ethernet stops working at all.
Discovered as part of
https://bugzilla.stlinux.com/show_bug.cgi?id=14148 triage
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a network namespace misfeature that bonding_masters looked at
current instead of the remembering the context where in which
/sys/class/net/bonding_masters was opened in to see which network
namespace to act upon.
This removes the need for sysfs to handle tagged directories with
untagged members allowing for a conceptually simpler sysfs
implementation.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port shouldn't be enabled unless its current MUX
state is DISTRIBUTING which is correctly handled by
ad_mux_machine(), otherwise the packet sent can be
lost because the other end may not be ready.
The issue happens on every port initialization, but
as the ports are expected to move quickly to DISTRIBUTING,
it doesn't cause much problem. However, it does cause
constant packet loss if the other peer has the port
configured to stay in STANDBY (i.e. SYNC set to OFF).
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the wrong parameter for setting EEE for RTL8111E-VL.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit 92fc43b415 ("r8169: modify the
flow of the hw reset."), rtl8169_hw_reset stomps during driver shutdown on
RxConfig bits which are needed for WOL on some versions of the hardware.
As these bits were formerly set from the r81{0x, 68}_pll_power_down methods,
factor them out for use in the driver shutdown (rtl_shutdown) handler.
I favored __rtl8169_get_wol() -hardware state indication- over
RTL_FEATURE_WOL as the latter has become a good candidate for removal.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Tested-by: Marc Ballarin <ballarin.marc@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Vitesse driver was using the RGMII_ID interface type to determine if
skew was necessary. However, we want to move away from using that
interface type, as it's really a property of the board's PHY connection.
However, some boards depend on it, so we want to support it, while
allowing new boards to use the more flexible "fixups" approach. To do
this, we extract the code which adds skew into its own function, and
call that function when RGMII_ID has been selected.
Another side-effect of this change is that if your PHY has skew set
already, it doesn't clear it. This way, the fixup code can modify the
register without config_init then clearing it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e uses paged frags, so any layer incorrectly pulling bytes from skb
can trigger a BUG in skb_pull()
[951.142737] [<ffffffff813d2f36>] skb_pull+0x15/0x17
[951.142737] [<ffffffffa0286824>] pptp_rcv_core+0x126/0x19a [pptp]
[951.152725] [<ffffffff813d17c4>] sk_receive_skb+0x69/0x105
[951.163558] [<ffffffffa0286993>] pptp_rcv+0xc8/0xdc [pptp]
[951.165092] [<ffffffffa02800a3>] gre_rcv+0x62/0x75 [gre]
[951.165092] [<ffffffff81410784>] ip_local_deliver_finish+0x150/0x1c1
[951.177599] [<ffffffff81410634>] ? ip_local_deliver_finish+0x0/0x1c1
[951.177599] [<ffffffff81410846>] NF_HOOK.clone.7+0x51/0x58
[951.177599] [<ffffffff81410996>] ip_local_deliver+0x51/0x55
[951.177599] [<ffffffff814105b9>] ip_rcv_finish+0x31a/0x33e
[951.177599] [<ffffffff8141029f>] ? ip_rcv_finish+0x0/0x33e
[951.204898] [<ffffffff81410846>] NF_HOOK.clone.7+0x51/0x58
[951.214651] [<ffffffff81410bb5>] ip_rcv+0x21b/0x246
pptp_rcv_core() is a nice example of a function assuming everything it
needs is available in skb head.
Reported-by: Bradley Peterson <despite@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving to Toeplitz function in RSS calculation.
Reporting rxhash in skb.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not updating common counters from data path.
The checksum counters are per ring, summarizing them when collecting statistics.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Canceling FCS removal where FW allows for better alignment
of incoming data.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds