This patch adds TX aggregation handler for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch maps sw and hw queues (for aggregations), so the right
mac80211 queue will be waken when ieee80211_wake_queue is invoked.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the possibility to disable the tx_power calibration.
In 5000 HW, this calibration is implemented in uCode, hence, it is
disabled in driver by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes some clean up in setup/cancel_deferred_work.
iwl_setup_deferred_work does the work that is common to 4965
and 5000, then it calls to HW specific handlers.
This patch also removes uneeded work_struct from iwl_priv.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the possibility not to compile the run time
calibrations. It also renames priv->sensitivity_work to
priv->run_time_calib_work, and moves bg_run_time_calib to iwl4965_base
since it is common to both: 4965 and 5000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps against lost interrupts and aids in debugging this.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes CONFIG_IWL4965_HT #ifdefs for iwl 4965 and 5000. 11n
feature is stable in those drivers and its mode of operation is determined
in mac80211, so this dependency is not needed any more.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mixed use of 'dev' and 'usbdev' for usbnet pointer can be confusing. So changing all 'usbnet *dev' to 'usbnet *usbdev'.
Also remove 'net_device *net' pointer from 'rndis_wext_bind' as 'usbdev->net' were already used where needed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't queue set_multicast_list work if WORK_SET_MULTICAST_LIST
flag already set.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver wasn't updating netif_carrier on link state changes but assumed
link layer was always up.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() is called from within rndis_command() so it
isn't very good place to do any work. Move to worker thread.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the alignment check in rt2x00dev.c to be independent of any
potential alignment measures that may be taken before. Just check
whether the payload is aligned based on the pointer addresses.
Note: This is preparatory for the dynamically mapped skb buffers
for the PCI drivers, as these need 4-byte alignment instead of the
currently enforced offset by 2 bytes.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAX_RX_SSI and MAX_NOISE are no longer used,
it is better to remove them entirely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RTS/CTS-to-self frames the IEEE80211_TX_CTL_USE_RTS_CTS flag
should be cleared for the tx_info flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To really force the FIELD macros to determine
the first bit of the register field we should
use the __builtin_choose_expr() function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not safe to use the skb->cb area for both the rxd and
skb_frame_desc data at the same time, while they occupy an overlapping
piece of memory. This can lead to hard to trace crashes as pointers
within skb_frame_desc are pointing into nowhere, or the rxd data is
overwritten with non-sense.
Fix it by copying the rxd to a small buffer on the stack.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rt2x00pci will be switched over to dynamically mapped skb's
instead of statically allocated DMA buffers, it no longer can handle
alignment of RX packets in a copy step, and needs to implement the
same scheme as rt2x00usb does.
In order to make the patch on dynamically mapped skb's smaller,
already centralize the alignment handling into rt2x00lib. This allows
us to move more code in rt2x00lib, and thus remove code duplication
between rt2x00usb and rt2x00pci.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data and data_len fields aren't really necessary in struct
skb_frame_desc, as they can be deduced from the skb itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX queues shouldn't be kicked after each frame that is put into the
queue. This could cause problems during RTS and CTS-to-self as well
as with fragmentation. In all those cases you want all frames to be
send out in a single burst. Off course we shouldn't let the queue fill
up entirely, thus we introduce a 10% threshold which, when reached,
will force the frames to be send out regardless of the frame.
In addition we should prevent queues to become full in such a way
that the tx() handler can fail. Instead of stopping the queue when
it is full, we should stop it when it is below the threshold.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The write_tx_data functions in rt2x00pci and rt2x00usb have
a lot in common. This moves that duplicate code into
rt2x00queue_write_tx_frame().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_kick_tx_queue() will loop over all entries
within the INDEX_DONE->INDEX range and kick each entry
which is pending to be kicked. This makes the kick_tx_queue
approach work the same as with the PCI drivers which
will allow for more code generalisation into rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qid should be initialized to QID_BEACON and QID_ATIM
for the beacon and atim quue. This makes checking for
a particular queue much saner, and it shouldn't harm,
because the only places where the value is send to
the hardware, we are allowed to send any value we
want since it is only used as argument in the
TX done register.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00_set_field functions are very often used,
but GCC is better able to optimize them when they
are macros instead of static inline functions.
After changing it to macro's each rt2x00 driver will
loose about ~3500 bytes in size.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb doesn't need the TX descriptor in the TX done path.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 doesn't send RTS or CTS-to-self frames through
the tx() callback functions so we don't need to check it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce code duplication by moving led structure initialization
into a per-driver function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reduce goto usage
* Mark if-statements which are true on hardware error unlikely()
* Cleanup debug messages
This makes the code look nicer and be better optimized since
the chance of hardware errors should be very small.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By using __ffs() the register offsets were always calculated
at run-time which all FIELD32/FIELD16 definitions were builtin
constants. This means we can heavily optimize the register handling
by allowing GCC to do all the work during compilation.
Add some compile_ffs() macros to perform the calculation at
compile time. After this each rt2x00 module size is reduced
by ~2500 bytes. And the stack size of several functions is reduced
as well which further limits the number of rt2x00 results in
'make checkstack'.
v2: Merge GertJan's bugfix of patch [1/11] directly into this patch
instead of providing it as seperate patch.
v3: Add extra parentheses when bitshifting __x
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.
The alternative is to select NEW_LEDS, which some drivers do.
This patch fixes the led_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.
This patch fixes the input_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample
The comment in the patch describes why it's safe to simply remove
the check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
fix race between:
ieee80211_open->ieee80211_led_radio->led_trigger_event->led_set_brightness->iwl3945_led_brightness_set
(which assumes that "led->priv" is not NULL)
and
iwl3945_pci_probe->iwl3945_setup_deferred_work->(...)->iwl3945_bg_alive_start->iwl3945_alive_start->iwl3945_led_register->iwl3945_led_register_led
which sets priv field in struct iwl3945_led
after
led->led_dev.brightness_set = iwl3945_led_brightness_set;
(...)
led_classdev_register(device, &led->led_dev);
http://kerneloops.org/guilty.php?guilty=iwl3945_led_brightness_set&version=2.6.25-release&start=1671168&end=1703935&class=oops
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: ipw3945-devel@lists.sourceforge.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a data alignment issue in the zd1211rw driver.
The IEEE80211_STYPE_QOS_DATA bit should be used as a bitwise test
to test for the presence of the 2 byte QoS control field.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes an issus that made "iwconfig eth1 power on" non-working.
When we get a "PS sleep" event, we have to confirm this to the firmware.
The confirm happens with a command, but this command is special: the
firmware won't send us a response. if_cs_host_to_card() is setting
priv->dnld_sent anyway, so this variable stayed at DNLD_DATA_SENT and
was never cleared back.
Now I put the special knowledge that the CMD_802_11_PS_MODE with
CMD_SUBCMD_SLEEP_CONFIRMED doesn't need to need a response by directly
clearing the dnld_sent state in lbs_send_confirmsleep().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When another scan is in progress, a direct scan gets dropped on the
floor. However, that direct scan is usually the scan that's really
needed by userspace, and gets stomped on by all the broadcast scans the
ipw2200 driver issues internally. Make sure the direct scan happens
eventually, and as a bonus ensure that the passive scan worker is
cleaned up when appropriate.
The change of request_passive_scan form a struct work to struct
delayed_work is only to make the set_wx_scan() code a bit simpler, it's
still only used with a delay of 0 to match previous behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the Philips CPWUA054/00 in p54usb.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there are no networks on the free list, expire the oldest one when
creating a new adhoc network. Because ipw2200 and the ieee80211 stack
don't actually cull old networks and place them back on the free list
unless they are needed for new probe responses, over time the free list
would become empty and creating an adhoc network would fail due to the !
list_empty(...) check.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: space prohibited between function name and open parenthesis '('
#22: FILE: drivers/net/wireless/airo.c:2907:
+ while ((IN4500 (ai, COMMAND) & COMMAND_BUSY) && (delay < 10000)) {
total: 0 errors, 1 warnings, 8 lines checked
./patches/wireless-airo-waitbusy-wont-delay.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Dan Williams <dcbw@redhat.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I moved the TX info into skb->cb apparently I forgot to change a
few places to put the p54-internal data into info->driver_data rather
than skb->cb. This should fix it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwl4965_mac_config.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch saves memory by reducing the size of the entry in the txq. It
was 640 because of the calibration commands. Calibration commands are now
sent as HUGE commands (using the extra 1024 bytes at the end of the command
txq), hence, there is no need for 640 in every entry any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch solves a bug in debugfs unregistration. iwlwifi registers its
debugfs files under cfg80211's dir, but removed its files only after having
unregistered mac80211 that removes cfg80211 debugfs dir. This garbaged
debugfs and didn't allow to rmmod and insmod iwlwifi several times in a
row.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak that the scan buffer isn't released
on exit.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch disables FAT channel when it is not permitted according to
the EEPROM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_get_hw_mode to iwl-core.h.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves Rx handlers from iwl 4965 only use to common use along
with iwl 5000, thus enables Rx path to iwl 5000.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds frame count limit to link quality host command.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves aggregation action code to iwl-tx.c in iwlcore.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_sta_modify_enable_tid_tx into iwl-sta.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds rxon assoc command for 5000 HW.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required to overcome a bug in 5000 HW byte count table.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch
1. moves TX reclaim flow into iwl-tx
2. separates command queue and tx queue reclaim flow
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes cases that the code raised or didn't decrease
the rate although the success ratio was not good.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves 4965 tx repsone into iwl-4965.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements 5000 HW tx response path.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This pach moves common tx response handlers to the header files
and iwl-tx.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds iwl5000_tx_repsons structure.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes driver state timeout checks on ucode alive response
only if run time ucode have been loaded.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds initial calibration framework for 5000 HW faimily.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_rx_missed_beacon_notif rx handler to iwl-rx.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves add_sta hander to iwl-sta.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds remove station functionality, which is required for
5000 and AP mode.
There are still some gaps in managment that need to be closed but it
provides sufficient functionality for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_rxq_stop into iwl-rx.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves txq_ctx_stop into iwl-tx.c iwlcore module.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors stop master function for 4965 and 5000.
Currently it duplicates the function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds apm stop function for 4965 and 5000.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements apm reset flow for 4965 and 5000.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch setups L1 L0S pci link values.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes 4965 from alive_resp and init_alivie_resp.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up alive_start routine. It removes 4965 from the common
code and moves the run time calibration reset into a common code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes notif_missed_beacons from priv since it was never
used. Missed beacons notification will have only meaning if roaming
will be implemented in mac80211.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unused variable from __iwl4965_down.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates driver's debugfs tree under wiphy->debugfsdir.
This patch fixes collision in debugfs if two or more NICs are plugged.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch increases iwl_cmd payload maximum size from 360 to 640
to fit some of iwl5000 commands as well.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the usage of the pointers to error and log tables
received in alive response w.r.t. the current uCode image.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fills the valid_rtc_data_addr handler in iwl5000.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the function iwl_dump_nic_error_log to iwlcore.
Remove sysfs entry it cannot be really triggered.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code misbehaved because it polled card status and always called the
"tx over" code-path.
This also fixes a hard lockup by not allowing and card interrupts while
transferring a TX frame or a command into the card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implemented rate adaptation support via 'iwconfig rate' API. It is now
possible to specify a bit-rate value and append 'auto'. That will configure
rate adaptation to use all bit-rates equal or lower than than selected value.
Made lbs_cmd_802_11_rate_adapt_rateset a direct command.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, b43legacy is broken due to
commit fbad4598ca826b994d0fd4ce3deebc9cd1960b31
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Thu May 15 12:55:29 2008 +0200
mac80211: move TX info into skb->cb
when compiled with only PIO or only DMA because I forgot to update two
stubs. This patch fixes it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While figuring out the TKIP problem I found a bug in the code which adds the 11g
rates. It's using sizeof instead of ARRAY_SIZE to terminate the for loop. This makes
it fall off the end of the rates array start into the frequency array instead. Running
"iwlist rate" should show the problem as there will always be 32 rates with the last
few being bogus.
The following patch will fix it.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k still uses the "(void*) skb->cb" direct cast, use IEEE80211_SKB_CB
instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we don't check for a command response early, but rather sleep,
then we might sleep despite an already-received command response.
This will lead to a command-timeout.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... because lbs_pr_XXX prefixes all messages with "libertas: "
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keep the timeout the same (1000*500 == 100000 * 5), but take shorter
naps. Makes downloading the firmware slightly faster.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->driver_lock has already been unlocked some lines above. This patch
fixes the sparse warning:
drivers/net/wireless/libertas/main.c:792:6: warning: context problem in 'lbs_thread': '_spin_unlock_irq' expected different context
drivers/net/wireless/libertas/main.c:792:6: context 'lock': wanted >= 1, got 0
Signed-of-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables b43 to do mesh networking, tested against my zd1211rw
dongle.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Range check for power_output were missing.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a case that a wrong maximal rate is selected when
searching for better configurations.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When exiting from stay in table state (e.g. timer expiration),
all the statistics are reset and the RS flow should not continue
but only after enough statistics are collected again.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the rndis_wlan driver to connect to TKIP PSK
networks. It uses the ASSOCIATION_INFORMATION RNDIS call to pull back
the IEs and sends them back to userspace using wireless events. Tested
on a few wireless networks I have access to. Based on the similar
code in ndiswrapper.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
[edit: cleanups]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_beacondone() is called from interrupt context,
this means we cannot use the mac80211 interface iterator
that uses the rtnl lock (since that uses a mutex which can sleep).
Instead we should use the atomic mac80211 interface iterator.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the antenna configuration has changed we should reset
the antenna RSSI value. Otherwise the value will be influenced
by the previous configuration quality which in turn will affect
the antenna diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link quality estimation became quite low for all rt2x00 drivers
because the number of retries it took to send the frame were
counted as failure.
This does not correspond to the legacy driver link quality calculation,
by not counting it we will send somewhat more optimistic values to
mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tx() handler runs while the device has disapeared,
we did return NETDEV_TX_OK but didn't free the skb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates the beacon template code to upload both templates,
if we never uploaded one before.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The grf5101 RF code needs to invoke grf5101_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max2820 RF code needs to invoke max2820_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sa2400 RF code needs to invoke sa2400_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The static function max2820_rf_set_channel is called with conf == NULL
within its compilation unit. Originally this defaulted to b/g channel
1, but "cfg80211 API for channels/bitrates, mac80211 and driver
conversion" (commit 8318d78a44) mistakenly
dropped this check. This patch minimally restores the expected
behavior.
Reported-by: Colin Lai <colin_sh@163.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: The world is not perfect patch.
tcp: Make prior_ssthresh a u32
xfrm_user: Remove zero length key checks.
net/ipv4/arp.c: Use common hex_asc helpers
cassini: Only use chip checksum for ipv4 packets.
tcp: TCP connection times out if ICMP frag needed is delayed
netfilter: Move linux/types.h inclusions outside of #ifdef __KERNEL__
af_key: Fix selector family initialization.
libertas: Fix ethtool statistics
mac80211: fix NULL pointer dereference in ieee80211_compatible_rates
mac80211: don't claim iwspy support
orinoco_cs: add ID for SpeedStream wireless adapters
hostap_cs: add ID for Conceptronic CON11CPro
rtl8187: resource leak in error case
ath5k: Fix loop variable initializations
This adds support for firmware markers.
With firmware markers it's easily possible to check whether the
firmware runs some codepath or not. The driver will throw a message
when the firmware executes a MARKER(x).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a firmware panic reason code that doesn't trigger a restart.
This is useful for firmware debugging and avoiding endless
restart loops. We can use FWPANIC_DIE to halt the firmware at a
well defined point.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to allow running the device without PCM firmware loaded.
Without PCM firmware we don't have hardware accelerated crypto on
devices with a core rev <= 10.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds some hooks for firmware debugging.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mac80211 and drivers to be multi-queue aware and
use that instead of the internal queue mapping. Also does a number
of cleanups in various pieces of the code that fall out and reduces
internal mac80211 state size.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the patch for the BCM4311 rev 2 was prepared, I misread the specs
and coded the wrong file name for the initvals firmware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw driver uses unaligned stack buffer for USB control
message. But it might cause stack corruption on non-coherent
platform, such as MIPS. Use DMA-aware buffers for USB transfer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having drivers start queues is just confusing, their ->start()
callback can block and do whatever is necessary, so let mac80211
start queues and have drivers wake queues when necessary (to get
packets flowing again right away.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a trigger for event log printing to debugfs.
It removes the triger from sysfs.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactores pci prob flow. It moves mac80211 registration
to the end, otherwise there is a race between error path in pci_probe
and mac_start.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds functionality to debugfs to enable or disable chain
noise or sensitivity calibrations.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch cleans up 4965 remaings from iwl-eeprom.c file.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WiFi/WiMax coexistence to iwl5000.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds all the handlers and functions needed for ucode
initialization flow.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds ucode initialization handler and functions to load
ucode for iwl5000 NIC.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds rx_handler_setup stub to iwl5000.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_txq_ctx_activate and iwl4965_txq_ctx_deactivate
to iwl-dev.h and removes 4965 prefix from their names.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up code in security.
1) uses the new pointer to ieee80211_key_conf passed with the tx_control.
2) resolves bug reported by Mirco Tischler (sends ADD_STA in ASYNC mode)
3) resolves bug reported by Volker Braun regarding dynamic WEP
4) drops a WEP packet which has been garbaged by firmware. This can
happen upon rekeying.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes SGI support. RS didn't look at the capabilities of the AP
before switching to SGI, this should lead to a stall in the traffic with an
AP that doesn't support SGI.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the sending part of the TX code into iwl-tx.c
including sending host commands.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors ieee80211_get_qos_ctrl function and its usage
in iwlwifi drivers. Function is moved as inline into iwl-helpers.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_tx_cmd to iwl_tx_cmd and cleans
collateral code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves station management functions into iwl-sta.c (iwlcore).
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_broadcast_addr to iwl_bcast_addr
and moves it to iwlcore.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes 4965 from iwl4965_rate_info structure and
associated variables.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes 4965 from iwl4965_frame struct and handling functions.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_tx_queue_update_write_ptr to
iwl_txq_update_write_ptr. This is a preparation for moving to iwl-tx.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new handler get_hw_cmd_size in hcmd_utils,
which should adjust the size of the command sent to the microcode
according to the current nic.
It also changes the RXON flow to make usage of this new handler.
The patch also adds iwl_rxon_cmd structure which is supperset for
5000 HW and 4965.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_tx_info to iwl_tx_info.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_queue to iwl_queue.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fills the needed data about HW capabilities in matters of
possible HT Tx MCS.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch follows the 11n spec in separation between Tx and Rx MCS
capabilities. Up until now, when configuring the HT possible set of Tx
MCS only Rx MCS were considered, assuming they are the same as the Tx MCS.
This patch fixed this by looking at low level driver Tx capabilities.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the contant of iwl4965_nic_start to the only place it is
being used.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes an old eeprom comment in probe flow.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[PATCH, take 2] libertas: reduce command retry time
In the normal case, an unsuccessful command would be retried for 10*5 seconds,
or 10*10 seconds in the worst case. This patch reduces this to 3*3 seconds,
or 3*10 seconds in the worst case.
I also reduced the time it takes to start a new command downloaded.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will create the following entry:
/sys/class/net/mshX
-- boot_options
| |-- ...
| `-- channel
...
... which I overlooked on my previous patch.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a patch from Shailendra Govardhan and Brian Cavagnolo.
It extends the MESH_CONFIG command to configure non-volatile parameters on
libertas devices that support them (e.g. OLPC Active Antenna).
This patch only implements the driver/firmware interface.
See http://dev.laptop.org/ticket/6823 for minimal testing results and known
issues.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We weren't properly handling multicast on the mesh interface. Fix that,
which involves setting up the hardware to use the union of dev->mc_list
for both eth%d and msh%d devices.
This means we can't do it directly from ->set_multicast_list() because
we'd need to lock the other device to read its list, and we can't do
that because it might deadlock. So punt the actual work to keventd.
Also, invoke the same when taking an interface down; for some reason the
core calls ->set_multicast_list while IFF_UP is still set in dev->flags
when we're taking it down, so its addresses don't get removed then.
We also convert MAC_MULTICAST_ADR to a direct command while we're at it,
removing one more entry from the big switch statement in the deprecated
lbs_prepare_and_send_command() function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the deprecated lbs_prepare_and_send_command() function for a
command which it doesn't understand is an error; complain loudly about
it even when we're not debugging.
The mesh stats bug, where we converted MESH_ACCESS to a direct command
but accidentally missed one user which was still trying to do it through
lbs_prepare_and_send_command(), would have been caught a lot quicker if
we'd done this sooner. Such bugs aren't entirely unlikely in future too,
as we convert more code to stop using this function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the pending removal of the tx_control structure
we can merge the RX and TX entry private data structure
in advance. This will temporarily increase the required
memory for the queue, but that overhead will only be limited.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the rxdesc structure is properly memsetted before passed to
the driver. This means we don't have to reinitialize the flags
and dev_flags fields in the drivers again.
This will prevent problems when the rxdone handler is adding
flags in a earlier status and will make the code look nicer
when we are adding more read attributes in the rxdone handler
in the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split rt2x00lib_write_tx_desc() up into a TX descriptor initializor
and TX descriptor writer.
This split is required to properly allow mac80211 to move its
tx_control structure into the skb->cb array.
The rt2x00queue_create_tx_descriptor() function will read all tx control
information and convert it into a rt2x00 TX descriptor information structure.
After that function is complete, we have all information we needed from the
tx control structure and are free to start writing into the skb->cb array
for our own purposes.
rt2x00queue_write_tx_descriptor() will be in charge of really sending
the TX descriptor to the hardware and kicking the TX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of replacing the statically allocated data DMA buffers with DMA-mapped
skb's we need to change the TXD handling of the PCI drivers, by moving the programming
of the buffer address fields to the actual TXD writing at TX time, instead of at start-up
time.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to usage of memmove() in rt2x00usb the descriptor can become
corrupted because it is being overwritten by the data part.
Overall having the descriptor in front of the frame is a bad idea,
we can however use the skb->cb array for this task, since that
contains more then enough room to hold the entire descriptor and
preserve the information long enough.
After this we can also cleanup the alignment code a bit to make it
work a bit more flexible to allow for all kinds of odd header lengths.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the integration of the mac80211 multiqueue patches it has become possible that the
mac80211 layer modifies the number of TX queues that is stored inside the ieee80211_hw
structure, especially when multi-queue is not selected.
The rt2x00 drivers are not well suited to handle that situation, as they allocate the
queue structures before mac80211 has modified the number of queues it is going to use,
and also expect the number of allocated queues to match the hardware implementation.
Hence, ensure that rt2x00 maintains by itself the number of queues that the hardware
supports, and, at the same time, making is not dependent on the preservation of contents
inside a mac80211 structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the last remaining information details read from ieee80211_tx_control
in the drivers to the txentry_desc structure. After this we can
remove ieee80211_tx_control from the argument list for the callback function,
which makes it easier when the control information is moved into skb->cb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx_status enumeration was broken since the introduction
of rt61pci. That driver uses different values to report the
status of the tx action.
This would lead to frames that were reported as success but
actually failed to be send out, or frames that were neither
successfull or failure which were reported as failure.
Fix this by change the TX status reporting and more explicitely
check for failure or success. Note that a third possibility is
added "unknown". Not all hardware (USB) can report the actual
TX status, for rt61pci some frames will receive this status
because the TXdone handler is never called for those frames.
This unknown will now be handled as neither success or failure,
so we no longer increment the failure counter while this conclusion
could not be determined from the real status of the frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove frame_type from skb_frame_desc and pass it
as argument to rt2x00debug_dump_frame().
Change data_len and desc_len to unsigned short
to save another 4 bytes in skb_frame_desc. Note that
this was the only location where the data_len and
desc_len was not yet treated as unsigned short.
This trim is required to help mac80211 with adding
the TX control and TX status informtation into the
skb->cb structure. When that happens, drivers will
have approximately 40 bytes left to use freely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix various problems:
- We converted MESH_ACCESS to a direct command but missed this caller.
- We were trying to access mesh stats even on meshless firmware.
- We should really zero the buffer if something goes wrong.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Gerald Willmann <gerald.willmann@econ.kuleuven.be>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Santiago Garcia Mantinan <hostap@manty.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes resource leaks in error cases due to urb submission
failures.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath5k_tasklet_rx, both status structures 'rxs' and 'rs' are
initialized at the top of the tasklet, but not within the loop.
If the loop is executed multiple times in the tasklet then the
variables may see changes from previous packets.
For TKIP, this results in 'Invalid Michael MIC' errors if two packets
are processed in the tasklet: rxs.flag gets set to RX_DECRYPTED by
mac80211 when it decrypts the first encrypted packet. The subsequent
packet will have RX_DECRYPTED set upon entry to mac80211, so mac80211
will not try to decrypt it.
We currently initialize all but two fields in the structures, so fix
the other two.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some network interfaces of the wireless drivers lack the 'device'
symlink in sysfs.
This patch lets the drivers create the links.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There will be no delay even when COMMAND_BUSY (defined 0x8000) is set:
0x8000 & (delay < 10000) will evaluate to 0 - when delay is 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a fix for OLPC ticket #6586: "SCAN command fails, timer doesn't
fire". In fact, the timer was firing; the problem was that the dnld_sent
state variable was not being updated after the timer expired, so
lbs_execute_next_command was not being called.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "registers" entry was incorrectly created in the procfs root instead
of the device specific directory. Move "registers" registration
immediately after the containing procfs directory is created.
Signed-off-by: Mathieu Chouquet-Stringer <mchouque@free.fr>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 4-bit reversal flip_4bit is replaced with the bitrev helper
bitrev8 and a 4-bit shift. The B43_WARN is moved to the location
where a register is read from for checking there. The other caller
explicitly passes an array index which is guaranteed to be within range
and so a B43_WARN is not added there.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Reviewed-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath5k_tasklet_rx, both status structures 'rxs' and 'rs' are
initialized at the top of the tasklet, but not within the loop.
If the loop is executed multiple times in the tasklet then the
variables may see changes from previous packets.
For TKIP, this results in 'Invalid Michael MIC' errors if two packets
are processed in the tasklet: rxs.flag gets set to RX_DECRYPTED by
mac80211 when it decrypts the first encrypted packet. The subsequent
packet will have RX_DECRYPTED set upon entry to mac80211, so mac80211
will not try to decrypt it.
We currently initialize all but two fields in the structures, so fix
the other two.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove duplicated include <linux/delay.h> in
drivers/net/wireless/b43/nphy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this adds initial IBSS support for the zydas zd1211rw:
convince driver that it can do IBSS mode. add mac80211 beacon_update callback.
IBSS merge and TSF updates don't work yet, but it makes the driver usable in
ad-hoc networks.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use net_device_stats from net_device structure instead of local.
Kill atmel_get_stats function, because by default it is used
identical internal_stats function from net/core/dev.c
No need to memset stats to 0, because they are allocated by kzalloc.
P.S. Someone should cleanup init_atmel_card function from unneeded
initializations to 0/NULL. Out of scope for this patch.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 <---> mac80211 <----> wpa_supplicant <---> NetworkManager
When a hardware scan is completed and another scan is requested in less
than two seconds, iwlwifi will not do the second scan and will pass the
error code -EAGAIN back to mac80211 where it quickly dies. The error
code is not passed along to the calling program wpa_supplicant. After a
timeout, wpa_supplicant will just give up but it will not know why the
scan failed. This is a weakness in the design.
I ran into this issue when I was trying to figure out why it takes more
an a minute for NetworkManager to connect after Networking has been
disabled and then re-enabled. I found a good deal of unnecessary work
being done because mac80211 requests authentication when the interface
is not configured, the ANY mode. I created an experimental passive
(NOTANY) mode for mac80211 to eliminate this case. Then NetworkManager
became so fast that I ran into the iwlwifi 2 second delay next scan
issue which we are discussing.
The patch resolves the problem by bypassing the delay if the scan request
is a direct scan. It should do less harm to the hardware.
Signed-off-by: Bill Moss <bmoss@CLEMSON.EDU>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a module parameter of fw_restart which determine if
the uCode will be restarted or not in case of error.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds sysfs version file that displays ucode version
and type.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the levels of debug prints, leaving only one level
in each debug print.
It was anoying and caused unnecessary prints on hot path.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports the debug_level from sysfs/bus/pci/drivers/iwl4965
to /sys/class/net/wlanX/device/debug_level
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use net_device_stats from net_device structure instead of local.
Changed airo_read_stats function parameter to net_device.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes spinlock priv->lock (apm_ops.init) is used before it has
been initialized.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the 4965 prefix to form iwl_kw and iwl_tx_queue structs,
as they are used mostly in iwlcore now.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits ucode's and driver's shared memory Rx index access to
match 4965 and 5000 offsets.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch leverages mac80211 configure_filter to enable iwl3945
monitor mode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch leverages mac80211 configure_filter to enable iwl4965
monitor mode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_4965_init_alive_start to iwl-4965.c.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl-sta into iwl-core.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does the following:
1 - change hw_nic_init from a handler to a function
2 - move hw_nic_init function to iwlcore
3 - open a new file - iwl-tx.c
4 - move all Tx queues initialization (part of NIC init) to iwl-tx.c
5 - move iwl_rx_init, previously as part of the NIC init, to iwl-rx.c
6 - iwl4965_tfd_frame rename to iwl_tfd_frame
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves disabeling Tx FIFOs in NIC SCD to seperate handlers
in 4965 and 5000 cards.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_set_rxon_ht to iwlcore under name
iwl_set_rxon_ht. It also moves collateral changes
iwl_is_channel_extension and iwl_is_fat_tx_allowed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports the debug_level to iwl_priv and changes
the format of the debug prints.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds iwl5000_build_addsta_hcmd handler.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_send_add_station to iwlcore
under new name iwl_send_add_sta.
Function uses build command handler in order to support
multiple HWs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes 4965 mark from rx_packet.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds EEPROM dump in debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes 4965 mark form the station entry structure.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes override of association channel with HT control channel.
The scenario is currently happening because disassociation flow
doesn't clean previous association information (such as is_ht and control
channel).
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves partialy rx code into iwl-rx.c as part of iwlcore.
The second part of the code can be merged only with moving of tx
code as well.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch maps A-MPDU HW queue to mac80211 SW queue scheme (as introduced
in patch "mac80211: QoS related cleanups"), when trying to perform
ieee80211_wake_queue.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed earlier, we can unify locking in struct sta_info
and use just a single spinlock protecting all members of the
structure that need protection. Many don't, but one of the
especially bad ones is the 'flags' member that can currently
be clobbered when RX and TX is being processed on different
CPUs at the same time.
Because having four spinlocks for different, mostly exclusive
parts of a single structure is overkill, this patch also kills
the ampdu and mesh plink spinlocks and uses just a single one
for everything. Because none of the spinlocks are nested, this
is safe.
It remains to be seen whether or not we should make the sta
flags use atomic bit operations instead, for now though this
is a safe thing and using atomic operations instead will be
very simple using the new static inline functions this patch
introduces for accessing sta->flags.
Since spin_lock_bh() is used with this lock, there shouldn't
be any contention even if aggregation is enabled at around the
same time as both requires frame transmission/reception which
is in a bh context.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Tomas Winkler <tomasw@gmail.com>
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kernel-provided clamp_val is identical, delete the private limit_value helper.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kernel-provided clamp_val is identical, delete the private limit_value helper.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-core.c: In function 'iwlcore_init_geos':
drivers/net/wireless/iwlwifi/iwl-core.c:323: error: implicit declaration of function 'iwlcore_init_ht_hw_capab'
This (or something like it) should be folded into the base patch to avoid
breaking bisection, please.
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (73 commits)
net: Fix typo in net/core/sock.c.
ppp: Do not free not yet unregistered net device.
netfilter: xt_iprange: module aliases for xt_iprange
netfilter: ctnetlink: dump conntrack ID in event messages
irda: Fix a misalign access issue. (v2)
sctp: Fix use of uninitialized pointer
cipso: Relax too much careful cipso hash function.
tcp FRTO: work-around inorder receivers
tcp FRTO: Fix fallback to conventional recovery
New maintainer for Intel ethernet adapters
DM9000: Use delayed work to update MII PHY state
DM9000: Update and fix driver debugging messages
DM9000: Add __devinit and __devexit attributes to probe and remove
sky2: fix simple define thinko
[netdrvr] sfc: sfc: Add self-test support
[netdrvr] sfc: Increment rx_reset when reported as driver event
[netdrvr] sfc: Remove unused macro EFX_XAUI_RETRAIN_MAX
[netdrvr] sfc: Fix code formatting
[netdrvr] sfc: Remove kernel-doc comments for removed members of struct efx_nic
[netdrvr] sfc: Remove garbage from comment
...
This patch fixes a bug in RX path, the frequency was wrongly set in the
ieee80211_rx_status. This bug led to an empty scan list in A band.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd_mac_tx_to_dev() could potentially free the skb, or hand it off
to mac80211 which might free it. Hence, this code needs to get the
usb pointer out of skb->cb before handing it off to that function.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When, for some reason, the rt2x00pci module fails to allocate DMA memory for
the queues, it tries to undo the complete initialization of the PCI device,
including freeing of the irq. This results in the following error in dmesg, as
the irq hadn't been requested yet:
[ 78.123456] Trying to free already-free IRQ 17
Fix this by implementing proper error handling code, instead of just using the
full uninitialization function.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During initialization the initialize() callback function
in rt2x00pci and rt2x00usb will cleanup the mess they made.
rt2x00lib shouldn't call uninitialize because the callback function already
cleaned up _and_ the DEVICE_INITIALIZED isn't set which causes the
rt2x00lib_uninitialize() to halt directly anyway. All that is required
to be cleaned up by rt2x00lib is the queue, and that can be done by
calling rt2x00queue_uninitialize() directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00pci allocates DMA for descriptor and data,
rt61pci doesn't use this for the beacon, but it can
use the descriptor part as temporary buffer instead
of using pskb_expand_head().
Using this temporary buffer is obviously much better
then reallocating the skb buffer...
At the same time we can set the data length for the
beacon queue at 0, to make sure no DMA is allocated for
data (but just for the descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make iwl4965_lq_sta->drv available even without CONFIG_MAC80211_DEBUGFS.
Signed-off-by: Yi Zhu <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression introduced by commit 7b463ced6 (prism54: set
carrier flags correctly) which causes the device to come up without
a carrier in AP-mode.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Strip assumes that the tty drivers always have a set_termios method which
may not be true. Check this when binding to the tty so that we don't oops
later.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/mac80211/wme.c: In function ‘wme_qdiscop_enqueue’:
net/mac80211/wme.c:219: warning: comparison is always false due to limited range of data type
drivers/net/wireless/p54/p54common.c: In function ‘p54_conf_tx’:
drivers/net/wireless/p54/p54common.c:947: warning: comparison is always false due to limited range of data type
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Filipus Klutiero <chealer@gmail.com>,
the rt2x00 Kconfig entries should be updated with
specific chipset notifications.
This cleans up Kconfig by explicitly mentioning the
supported chipsets for each drivers, and uses the
same chipset family names as mentioned on the Ralink website.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes several problems I had:
* when removing the card while the card was scanning or associtating,
it could happen that destroy_workqueue() stuck and didn't return.
* make sure the command function doesn't run while we remove the list
of pending commands
* for still unknown reason, I had calls to lbs_stop_card() with
priv==NULL
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They don't return anything meaningfull and no-one cares about their results.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* make debug output match the variable name
* always report that lbs_remove_rtap() has has been exited
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This
* makes the queue number passed to drivers a u16
(as it will be with skb_get_queue_mapping)
* removes the useless queue number defines
* splits hw->queues into hw->queues/ampdu_queues
* removes the debugfs files for per-queue counters
* removes some dead QoS code
* removes the beacon queue configuration for IBSS
so that the drivers now never get a queue number
bigger than (hw->queues + hw->ampdu_queues - 1)
for tx and only in the range 0..hw->queues-1 for
conf_tx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue info in struct ieee80211_tx_status is never used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback takes a ieee80211_tx_queue_stats with a contained
array of ieee80211_tx_queue_stats_data, remove the former, rename
the latter to ieee80211_tx_queue_stats and make tx_stats() take
the array directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler