Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The req operation REQ_OP is separated from the rq_flag_bits
definition. This converts the block layer drivers to
use req_op to get the op from the request struct.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now the the HS-DDR mode clock timings have been corrected, we can
re-enable these modes on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC clock timings were incorrectly calculated, when the conversion
from delay value to delay phase was done.
The 50M DDR and 50M DDR 8bit timings are off, and make eMMC DDR
unusable. Unfortunately it seems different controllers on the same SoC
have different timings. The new settings are taken from mmc2, which is
commonly used with eMMC.
The settings for the slower timing modes seem to work despite being
wrong, so leave them be.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When IS_ERR_VALUE was removed from the mmc core code, it was replaced
with a simple not-zero check. This does not work, as the value checked
is the return value for mmc_select_bus_width, which returns the set
bit width on success. This made eMMC modes higher than HS-DDR unusable.
Fix this by checking for a positive return value instead.
Fixes: 287980e49f ("remove lots of IS_ERR_VALUE abuses")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zHa6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.7 rc1. They are based on a
commit earlier in the merge window and have been tested in linux-next
for a while.
MMC core:
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly"
* tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-acpi: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: sdhci-pci: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: longer timeout for long read time quirk
mmc: dw_mmc: rockchip: Set the drive phase properly
mmc: dw_mmc: fix the wrong max_blk_size
mmc: dw_mmc-rockchip: add MMC_CAP_CMD23 capabilities
mmc: sdhci-acpi: Ensure connected devices are powered when probing
ACPI / PM: Export acpi_device_fix_up_power()
mmc: block: Pause re-tuning while switched to the RPMB partition
mmc: block: Always switch back to main area after RPMB access
mmc: core: Add a facility to "pause" re-tuning
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.
This patch will...
() Increase the long read time quirk timeout from 300ms to 600ms. Original
author of that quirk says 300ms was only a guess and that the number
may need to be raised in the future.
() Add this specific MMC to the quirk
Signed-off-by: Matt Gumbel <matthew.k.gumbel@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Historically for Rockchip devices we've relied on the power-on
default (or perhaps the firmware setting) to get the correct drive
phase for dw_mmc devices. This worked OK for the most part, but:
* Relying on the setting just "being right" is a bit fragile.
* As soon as there is an instance where the power on default is wrong or
where the firmware didn't configure this properly then we'll get a
mysterious failure.
In commit 7a03fe6f48 ("clk: rockchip: reset init state before mmc card
initialization") we actually started setting this explicitly in the
kernel, but that commit wasn't quite right and also wasn't quite
enough. See <https://patchwork.kernel.org/patch/9085311/> for some
details.
Let's explicitly set this phase in dw_mmc.
The comments inside this patch try to explain the situation quite
throughly, but the high level overview of this is:
Before this patch on rk3288 devices tested (after revert of the clock
patch described above):
* eMMC: 180 degrees
* SDMMC/SDIO0/SDIO1: 90 degrees
After this patch:
* Use 90 degree phase offset usually.
* Use 180 degree phase offset for MMC_DDR52, SDR104, HS200.
That means we are _changing_ behavior for those devices in this way:
* If we have HS200 eMMC or DDR52 eMMC, we'll run ID mode at 90
degrees (vs 180) but otherwise have no change.
* For any non-HS200 / non-DDR52 eMMC devices we'll now _always_ run at
90 degrees (vs 180). It seems fairly unlikely that building modern
hardware is using an eMMC that isn't using DDR52 or HS200, of course.
* For SDR104 cards we'll now run with 180 degree phase offset (vs 90).
It's expected that 90 degree phase offset would have worked OK, but
this gives us extra margin.
I have tested this by inserting my collection of uSD cards (mostly UHS,
though a few not) into a veyron_minnie and confirmed that they still
seem to enumerate properly. For a subset of them I tried putting a
filesystem on them and also tried running mmc_test.
Fixes: 7a03fe6f48 ("clk: rockchip: reset init state before mmc card initialization")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to DesignWare TRM, BLKSIZ is 16bits.
Then it's correct that max_blk_size should be 0xFFFF, not 0x10000.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
Some devices connected to the SDHCI controller may have separate enabling
lines that are controlled through GPIO. These devices need to be powered
on and enabled before probing. This is to ensure all devices connected can
be seen by the controller.
Note, for "stable" this patch depends on the following change:
commit 78a898d0e3 ("ACPI / PM: Export acpi_device_fix_up_power()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reported-and-tested-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112571
Link: http://lkml.kernel.org/r/CA+7w51inLtQSr656bJvOjGG9oQWKYPXH+xxDPJKbeJ=CcrkS9Q@mail.gmail.com
Pull block driver updates from Jens Axboe:
"On top of the core pull request, this is the drivers pull request for
this merge window. This contains:
- Switch drivers to the new write back cache API, and kill off the
flush flags. From me.
- Kill the discard support for the STEC pci-e flash driver. It's
trivially broken, and apparently unmaintained, so it's safer to
just remove it. From Jeff Moyer.
- A set of lightnvm updates from the usual suspects (Matias/Javier,
and Simon), and fixes from Arnd, Jeff Mahoney, Sagi, and Wenwei
Tao.
- A set of updates for NVMe:
- Turn the controller state management into a proper state
machine. From Christoph.
- Shuffling of code in preparation for NVMe-over-fabrics, also
from Christoph.
- Cleanup of the command prep part from Ming Lin.
- Rewrite of the discard support from Ming Lin.
- Deadlock fix for namespace removal from Ming Lin.
- Use the now exported blk-mq tag helper for IO termination.
From Sagi.
- Various little fixes from Christoph, Guilherme, Keith, Ming
Lin, Wang Sheng-Hui.
- Convert mtip32xx to use the now exported blk-mq tag iter function,
from Keith"
* 'for-4.7/drivers' of git://git.kernel.dk/linux-block: (74 commits)
lightnvm: reserved space calculation incorrect
lightnvm: rename nr_pages to nr_ppas on nvm_rq
lightnvm: add is_cached entry to struct ppa_addr
lightnvm: expose gennvm_mark_blk to targets
lightnvm: remove mgt targets on mgt removal
lightnvm: pass dma address to hardware rather than pointer
lightnvm: do not assume sequential lun alloc.
nvme/lightnvm: Log using the ctrl named device
lightnvm: rename dma helper functions
lightnvm: enable metadata to be sent to device
lightnvm: do not free unused metadata on rrpc
lightnvm: fix out of bound ppa lun id on bb tbl
lightnvm: refactor set_bb_tbl for accepting ppa list
lightnvm: move responsibility for bad blk mgmt to target
lightnvm: make nvm_set_rqd_ppalist() aware of vblks
lightnvm: remove struct factory_blks
lightnvm: refactor device ops->get_bb_tbl()
lightnvm: introduce nvm_for_each_lun_ppa() macro
lightnvm: refactor dev->online_target to global nvm_targets
lightnvm: rename nvm_targets to nvm_tgt_type
...
Re-tuning is not possible when switched to the RPMB
partition. However re-tuning should not be needed
if re-tuning is done immediately before switching,
a small set of operations is done, and then we
immediately switch back to the main partition.
A previous patch ensured that we immediately switch
back to the main partition.
This patch uses the new facility to "pause" re-tuning
before switching to the RPMB partition, and to "unpause"
it after switching from the RPMB partition.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to support the use of the RPMB partition with transfer
modes that might require re-tuning, always switch back to the main
area after RPMB access.
RPMB is accessible only via IOCTL so only those paths are affected.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning is not possible when switched to the RPMB
partition. However re-tuning should not be needed
if re-tuning is done immediately before switching,
a small set of operations is done, and then we
immediately switch back to the main partition.
To ensure that re-tuning can't be done for a short
while, add a facility to "pause" re-tuning.
The existing facility to hold / release re-tuning
is used but it also flags re-tuning as needed to cause
re-tuning before the next command (which will be the
switch to RPMB).
We also need to "unpause" in the recovery path, which
is catered for by adding it to mmc_retune_disable().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki).
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez).
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada).
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi).
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches).
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat).
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao).
- ACPI cpufreq driver cleanups (Viresh Kumar).
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla).
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann).
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla).
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham).
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King).
- Intel Broxton support for the intel_idle driver (Len Brown).
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach).
- ARM cpuidle cleanups (Jisheng Zhang).
- Intel Kabylake support for the RAPL power capping driver (Jacob Pan).
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner).
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WM89
-----END PGP SIGNATURE-----
Merge tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The majority of changes go into the cpufreq subsystem this time.
To me, quite obviously, the biggest ticket item is the new "schedutil"
governor. Interestingly enough, it's the first new cpufreq governor
since the beginning of the git era (except for some out-of-the-tree
ones).
There are two main differences between it and the existing governors.
First, it uses the information provided by the scheduler directly for
making its decisions, so it doesn't have to track anything by itself.
Second, it can invoke drivers (supporting that feature) to adjust CPU
performance right away without having to spawn work items to be
executed in process context or similar. Currently, the acpi-cpufreq
driver is the only one supporting that mode of operation, but then it
is used on a large number of systems.
The "schedutil" governor as included here is very simple and mostly
regarded as a foundation for future work on the integration of the
scheduler with CPU power management (in fact, there is work in
progress on top of it already). Nevertheless it works and the
preliminary results obtained with it are encouraging.
There also is some consolidation of CPU frequency management for ARM
platforms that can add their machine IDs the the new stub dt-platdev
driver now and that will take care of creating the requisite platform
device for cpufreq-dt, so it is not necessary to do that in platform
code any more. Several ARM platforms are switched over to using this
generic mechanism.
In addition to that, the intel_pstate driver is now going to respect
CPU frequency limits set by the platform firmware (or a BMC) and
provided via the ACPI _PPC object.
The devfreq subsystem is getting a new "passive" governor for SoCs
subsystems that will depend on somebody else to manage their voltage
rails and its support for Samsung Exynos SoCs is consolidated.
The rest is support for new hardware (Intel Broxton support in
intel_idle for one example), bug fixes, optimizations and cleanups in
a number of places.
Specifics:
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki)
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez)
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada)
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi)
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches)
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat)
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao)
- ACPI cpufreq driver cleanups (Viresh Kumar)
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla)
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann)
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla)
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham)
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King)
- Intel Broxton support for the intel_idle driver (Len Brown)
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach)
- ARM cpuidle cleanups (Jisheng Zhang)
- Intel Kabylake support for the RAPL power capping driver (Jacob
Pan)
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner)
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger)"
* tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (112 commits)
intel_pstate: Clean up get_target_pstate_use_performance()
intel_pstate: Use sample.core_avg_perf in get_avg_pstate()
intel_pstate: Clarify average performance computation
intel_pstate: Avoid unnecessary synchronize_sched() during initialization
cpufreq: schedutil: Make default depend on CONFIG_SMP
cpufreq: powernv: del_timer_sync when global and local pstate are equal
cpufreq: powernv: Move smp_call_function_any() out of irq safe block
intel_pstate: Clean up intel_pstate_get()
cpufreq: schedutil: Make it depend on CONFIG_SMP
cpufreq: governor: Fix handling of special cases in dbs_update()
PM / OPP: Move CONFIG_OF dependent code in a separate file
cpufreq: intel_pstate: Ignore _PPC processing under HWP
cpufreq: arm_big_little: use generic OPP functions for {init, free}_opp_table
PM / OPP: add non-OF versions of dev_pm_opp_{cpumask_, }remove_table
cpufreq: tango: Use generic platdev driver
PM / OPP: pass cpumask by reference
cpufreq: Fix GOV_LIMITS handling for the userspace governor
cpupower: fix potential memory leak
PM / devfreq: style/typo fixes
PM / devfreq: exynos: Add the detailed correlation for Exynos5422 bus
..
Some eMMCs set the partition switch timeout too low.
Now typically eMMCs are considered a critical component (e.g. because
they store the root file system) and consequently are expected to be
reliable. Thus we can neglect the use case where eMMCs can't switch
reliably and we might want a lower timeout to facilitate speedy
recovery.
Although we could employ a quirk for the cards that are affected (if
we could identify them all), as described above, there is little
benefit to having a low timeout, so instead simply set a minimum
timeout.
The minimum is set to 300ms somewhat arbitrarily - the examples that
have been seen had a timeout of 10ms but were sometimes taking 60-70ms.
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested on a Salvator-X board with a Spectec SDW-823 WLAN card.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have two SDIO WLAN cards which specify being SDIO Rev. 1.1 cards but
their FUNCE tuple reports the smaller size of a Rev 1.0 card. So,
enforce 1.0 on these cards to avoid reading the not present registers.
They are not really used anyhow. My cards initialize properly after this
patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add some logging to make it clear just how the emmc timeout
was handled.
Signed-off-by: Ken Sumrall <ksumrall@android.com>
[AmitP: cherry-picked this Android patch from aosp
common kernel android-4.4]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit d6463f170cf0 ("mmc: sdhci: Remove redundant runtime PM calls"),
some of original sdhci_do_xx() function wrappers becomes meaningless,
so remove them.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs200() and mmc_select_hs() will keep the timing
as before if switch fails. So it's meaningless to print the
failed switched mode outside based on the current host timing.
Furthermore, the original print is wrong, it should be:
pr_warn("%s: switch to %s failed\n",
mmc_hostname(card->host),
mmc_card_hs(card) ? "high-speed" :
(mmc_card_hs200(card) ? "hs200" : ""));
Since we already have error message in mmc_select_hs200(),
simply remove it outside.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently MMC core will keep going if HS200/HS timing switch failed
with -EBADMSG error by the assumption that the old timing is still valid.
However, for mmc_select_hs200 case, the signal voltage may have already
been switched. If the timing switch failed, we should fall back to
the old voltage in case the card is continue run with legacy timing.
If fall back signal voltage failed, we explicitly report an EIO error
to force retry during the next power cycle.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 61b914eb81f8 ("mmc: sdhci-of-arasan: add phy support for
sdhci-of-arasan") introduce phy support for arasan. According to
the vendor's databook, we should make sure the phy is in poweroff
status before we configure the clk stuff. Otherwise it may cause
some IO sample timing issues from the test. And we don't need this
extra operation while running in low performance mode since phy
doesn't trigger sampling block.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
CC: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD0 or hardware reset may invalidate the cache, so it needs to be
flushed before reset.
In the case of recovery, we can't expect flushing the cache to work
always, but have a go and ignore errors.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
And return the old clock rate if something went wrong.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We had a regression on r8a7740 where the SDHI clock was a generic
peripheral clock, so changing its rate was not desired. This should be
fixed in the clock driver. However, it also shows that the new clock
calculation should only be used on tested systems. Add a check for that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RCar Gen2 and later implementations of TMIO/SDHI have their own set of
features and additions. FAST_CLK_CHG is just one of them and I see a few
others being added soon. Some may work on older chipsets but this needs
to be tested case by case. Instead of adding a bunch of flags for each
feature, add a global RCar2+ one for now. We can still break out
features if the need arises.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save a few lines, the codebase is large enough.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller claims to support SDR104. In fact, it only supports a
degraded SDR104 since the maximum frequency of the SD clock is 120 MHz
instead of 208 MHz.
The sdhci core is unaware of it and will compute a wrong clock divider.
We can deal with this specific case by using presets.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some boards need different pin drive strength for the UHS mode. Add an
optional pinctrl setting with two pin states covering UHS speeds and
other speeds.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a start_signal_voltage_switch() operation to support enabling of
UHS modes.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver in its current form does not support UHS at all due to
a missing start_signal_voltage_switch callback.
Also when this callback is added we should let the device tree control
UHS capabilities using the standard mmc bindings.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that reading CTL_STATUS is consistent, we can remove CTL_STATUS2 and
document how this is handled internally.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This bit has a different meaning in SDHI and original TMIO. Document
that and use the proper naming.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prevent confusion, use the virtual u32 CTL_STATUS in card_busy() the
same way as in other parts of this driver.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BIT() makes it easier to match the bits to the datasheet. This is
especially important here, since some variants have different names in
their datasheets (like with Renesas R-Car).
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Looking at the backlogs, I am not the only one who missed that the above
functions do not read u32 from one register, but create a virtual u32
from reading to adjacent u16 registers (which depending on 'bus_shift'
can be up to 8 byte apart). Because this driver supports old hardware
for which we don't have documentation, I first wrongly assumed there was
a variant which had a few u32 registers. Let's give the functions more
descriptive names to make it more obvious what is happening.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The legacy user space for n900 relies on the MMC slot names.
Let's check if those are passed in pdata and use them.
As this makes the DT booting compatible with legacy booting,
we should be able to start dropping omap3 legacy booting
support in v4.8.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no support for this platform in the kernel anymore.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no support for this platform in the kernel anymore. Make the
Kconfig text more generic, so it won't get stale anymore.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A last minute fix applied by Ulf made room for some simplification.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to have a public and private header file. Merge them
into a private one, so looking up symbols is less confusing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Having just one irq handler again, let's include the 'card_status'
function in the main handler which is way more readable. Drop a useless
debug output while here. It should be a dev_dbg in case we ever need it
again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We removed installation of separate handlers previously, so we can also
remove the separate handlers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no user left in the kernel, so this code can be removed.
(Legacy, non-DT sh_mobile boards have been removed a while ago.) The
diff looks more complicated than it is: The if-block for multiplexed isr
is now the main code path, the rest is removed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We won't access an index based array to get our DT config, but create
separate structs instead. So, remove the array which only wastes memory.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of using an mmc specific implementation to deal with indexes
through a BITMAP, let's convert to use the IDA library.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the allocation of a new partition fails, let's make sure to also
release the previously picked device index.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
defined(CONFIG_LEDS_CLASS) || (defined(CONFIG_LEDS_CLASS_MODULE) && \
defined(CONFIG_MMC_SDHCI_MODULE))
is equivalent to:
defined(CONFIG_LEDS_CLASS) || (defined(CONFIG_LEDS_CLASS_MODULE) && \
defined(MODULE))
and it can also be written shortly as:
IS_REACHABLE(CONFIG_LEDS_CLASS)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_SDR104_NEEDS_TUNING was originally named SDHCI_HS200_NEEDS_TUNING
and was added in commit 069c9f1428 ("mmc: host: Adds support for eMMC
4.5 HS200 mode").
That commit conflated SDHCI_SDR50_NEEDS_TUNING and SDHCI_HS200_NEEDS_TUNING
due to what appears to be misplaced parentheses.
Commit 156e14b126 ("mmc: sdhci: fix caps2 for HS200") made HS200
configuration equivalent to SDR104 configuration, renaming
SDHCI_HS200_NEEDS_TUNING to SDHCI_SDR104_NEEDS_TUNING despite tuning for
HS200 now being non-optional.
The mix-up with SDHCI_SDR50_NEEDS_TUNING remained and became more obvious
after commit 4b6f37d3a3 ("mmc: sdhci: clean up sdhci_execute_tuning()
decision") where the author noted the patch was "reflecting what the
original code was doing, it shows that it may not be what the author
actually intended."
The way the code is currently written, SDHCI_SDR104_NEEDS_TUNING
causes tuning to be done always for SDR50 mode if SDR104 mode is
also supported by the host controller. That makes no sense because
we already have capabilities bit SDHCI_USE_SDR50_TUNING and
corresponding flag SDHCI_SDR50_NEEDS_TUNING for that purpose.
Given the dubious origins of SDHCI_SDR104_NEEDS_TUNING, it seems
reasonable to remove it. The benefit being SDR50 mode will now not
un-nessessarily do tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Swap the call order of sdhci_alloc_host() and platform_get_irq().
It makes sdhci_alloc_host() the last function that can fail in the
sdhci_pltfm_init(). So, we can drop the sdhci_free_host() call from
the failure path.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Call devm_ioremap_resource() right after platform_get_resource().
This saves the error check of platform_get_resource() because
devm_ioremap_resource() checks if the given resource is NULL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The chain of devm_request_mem_region() and devm_ioremap() can be
replaced with devm_ioremap_resource(). Also, we can drop the error
messages because devm_ioremap_resource() displays similar messages
on error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the managed variant of ioremap().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the managed variant of request_mem_region().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function platform_get_irq() can fail; it returns a negative error
code on failure. A negative IRQ number will make sdhci_add_host() fail
to request IRQ anyway, but it makes sense to let it fail earlier here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The requirement resource_size >= 0x100 may not necessarily be
reasonable; for example, sdhci-dove appears to sidestep some
registers in sdhci_dove_readw().
Moreover, current code displays an error message for too small
resource size, but still moves forward.
Every DT should be responsible for describing its properties
correctly, so lets's remove this error message from the common
framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This if-block is going to call mmc_card_set_blockaddr(), so
mmc_card_blockaddr() right before it is redundant.
I am fixing the block comment style while I am here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
simple-pwrseq and emmc-pwrseq drivers rely on platform_device
structure from of_find_device_by_node(), this works mostly. But, as there
is no driver associated with this devices, cases like default/init pinctrl
setup would never be performed by pwrseq. This becomes problem when the
gpios used in pwrseq require pinctrl setup.
Currently most of the common pinctrl setup is done in
drivers/base/pinctrl.c by pinctrl_bind_pins().
There are two ways to solve this issue on either convert pwrseq drivers
to a proper platform drivers or copy the exact code from
pcintrl_bind_pins(). I prefer converting pwrseq to proper drivers so that
other cases like setting up clks/parents from dt would also be possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds to_pwrseq_emmc() macro to make the code more readable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds to_pwrseq_simple() macro to make the code more readable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ifdef's make the code more complicated and harder to read.
Move all the LED code together to reduce the ifdef's to
one place.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some error paths in sdhci_add_host() simply returned without
cleaning up. Also the return value from mmc_add_host()
was not being checked.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_AGGRESSIVE_PM for Broxton host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_AGGRESSIVE_PM for Broxton host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk is not used anymore so
remove it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disabling the internal clock while configuring the SD card clock can
lead to internal clock stabilization issue and/or unexpected switch to
the base clock when using presets.
A quirk SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST was introduced to fix
these bugs. The cause was assumed to be a too long internal
re-synchronisation but it seems in some cases the delay (even if longer)
doesn't fix this bug. The safest workaround is to not disable/enable the
internal clock during the SD card clock configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to remove the SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST and to
reduce code duplication, put the code relative to the SD clock
configuration in a function which can be used by hosts for the
implementation of the ->set_clock() callback.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are no need to have two versions of sdhci_runtime_pm_bus_off|on(),
depending on whether CONFIG_PM is set or unset. Thus it's easy to move the
implementation of these functions a bit earlier to avoid the unnecessary
pre-definition of them, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
A platform_driver does not need to set an owner, it will be populated
by the driver core.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Moreover as SDHCI have its own wrapper functions for runtime PM these
becomes superfluous, so let's remove them as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
The eMMC HW reset may be implemented either via the host ops ->hw_reset()
callback or through DT and the eMMC pwrseq. Additionally some eMMC cards
don't support HW reset.
To allow a reset to be done for the different combinations of mmc hosts
and eMMC/MMC cards, let's implement a fallback via trying a regular power
cycle. This improves the mmc block layer retry mechanism of failing I/O
requests.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
[Ulf: Rewrote changelog]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
When trying to use this driver with the common clock framework, enabling
the clock fails because it was not prepared. This fixes the problem by
calling clk_prepare and clk_enable in a single function. Ditto for
clk_disable_unprepare.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Unwiding from an error in davinci_mmcsd_probe was a mess. Some errors were
not handled and not all paths unwound correctly. Also using devm_ where
possible to simplify things.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, no dw_mmc variant drivers use this callback, let's
remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We combine what dw_mci_exynos_setup_clock does with init
hook to simplify the code
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We remove setup_clock hook and combine it into
init hook to simplify the code
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of Exynos has the Security management Unit(SMU).
This patch adds the function for controlling SMU.
In future, if exynos needs to control SMU, it can be implemented
in "config_smu" function, not "init" function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all is deprecated and should be
replaced by more explicit synchronous and asynchronous
terminate functions. This change is based on the
commit b36f09c3c4 ("dmaengine: Add transfer termination
synchronization support"). Currently dw_mci_stop_dma
may be called under the spinlock, let's migrate
dmaengine_terminate_all to async terminate. This could
avoid the race condition of use-after-free resouce of
dmaengine once slave-dma driver implement the synchronize
method.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Without MMC_CAP_ERASE support, we fail to mount partition
with "discard" option since mmc_queue_setup_discard is limited
for checking mmc_can_erase. Without doing mmc_queue_setup_discard,
blk_queue_discard fails to test QUEUE_FLAG_DISCARD flag, so we get
the following log from f2fs(actually similar to other file system):
mounting with "discard" option, but the device does not support discard
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_rockchip_pmops just copy-paste what dw_mci_pltfm_pmops
have done. Let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement voltage switch, supporting modes up to SDR-50.
Based on work by Shinobu Uehara, Rob Taylor, William Towle and Ian Molton.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting frequency to 0 is not enough, the clock explicitly has to be
disabled. Otherwise voltage switching (which needs SDCLK to be quiet)
fails for various cards.
Because we now do the 'new_clock == 0' check right at the beginning,
the indentation level of the rest of the code can be decreased a little.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Starting the clock is always done after frequency change anyhow, so we can
do it directly after the clock calculation and remove the specific calls.
This is the first part of doing proper clock de-/activation at calculation
time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on work by Shinobu Uehara and Ben Dooks. This adds the voltage
switch operation needed for all UHS-I modes, but not the tuning needed
for SDR-104 which will come later.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently tmio_mmc assumes that the input clock frequency is fixed and
only its own clock divider can be changed. This is not true in the
case of sh_mobile_sdhi; we can use the clock API to change it.
In tmio_mmc:
- Delegate setting of f_min from tmio to the clk_enable operation (if
implemented), as it can be smaller than f_max / 512
- Add an optional clk_update operation called from tmio_mmc_set_clock()
that updates the input clock frequency
- Rename tmio_mmc_clk_update() to tmio_mmc_clk_enable(), to avoid
confusion with the clk_update operation
In sh_mobile_sdhi:
- Make the setting of f_max conditional; it should be set through the
max-frequency property in the device tree in future
- Set f_min based on the input clock's minimum frequency
- Implement the clk_update operation, selecting the best input clock
frequency for the bus frequency that's wanted
sh_mobile_sdhi_clk_update() is loosely based on Kuninori Morimoto's work
in sh_mmcif.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the clk_enable operation to take a pointer to the struct
tmio_mmc_host and have it set f_max. For consistency, also change the
clk_disable operation to take a pointer to struct tmio_mmc_host.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch provides some tracepoints for the lifecycle of a mmc request
from starting to completion to help with performance analysis of MMC
subsystem.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
unnecessary indirection via 'struct device' back to omap_hsmmc_host
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The string "MMCSDCLK" is not actually used for clock lookup, so can be
removed.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As there are two callers of sh_mmcif_set_power() and because its only
additional action is to check for a valid regulator, let's just remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Both from a runtime PM and clock management point of view, the ->set_ios()
code is unnecessary complex.
A suboptimal path is also executed when the mmc core requests a clock rate
of zero. As that happens during the card initialization phase, trying to
save power by decreasing the runtime PM usage count and gating the clock
via clk_disable_unprepare() is just superfluous.
Moreover, from a runtime PM point of view the core will anyway keep the
device active during the entire card initialization phase.
Restructure the code to rely on the ios->power_mode to understand when the
runtime PM usage count needs to be increased. Let's also deal with clock
rate changes by simply applying the rate.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While accessing the device, make sure it stays active by increasing the
runtime PM usage count for it.
Let's also defer to enable runtime PM until we really need access to the
device. This also enables the error path in ->probe() to become simpler.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
eMMC HS-DDR no longer works on the A80, despite it working when support
for this developed.
Disable it for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ignore_children flag is used only when CONFIG_PM is set, so let's move
it into that section within the struct dev_pm_info.
Move also the corresponding pm_suspend_ignore_children() API out of
device.h into pm_runtime.h, to be consistent with similar APIs.
Unfortunate this causes the Toshiba PCI SD mmc host driver to fail to
compile as it needs pm_runtime.h, so let's fix this here as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Baytrail eMMC/SD/SDIO host controllers have been known to
hang. A change to a hardware setting has been found to
reduce the occurrence of such hangs. This patch ensures
the correct setting.
This patch applies cleanly to v4.4+. It could go to
earlier kernels also, so I will send backports to the
stable list in due course.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tegra124 has been randomly hanging during system suspend when entering
the Tegra LP1 low power state. The hang is caused by the Tegra SDHCI
driver and linked to the UHS-I tuning sequence. Disabling the UHS-I
modes for Tegra124 prevents any hangs from occurring when entering
system suspend.
Unfortunately, the tuning sequence described in the public Tegra
documentation is incomplete and on inspection of the current tuning
sequence that has been implemented is also incomplete and may cause
problems. In the short-term it is safer to disable UHS-I modes for now
and fix later because it would be too large of a change to simply patch
now. Therefore, disable UHS-I modes for Tegra124.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 520bd7a8b4 ("mmc: core: Optimize boot time by detecting cards
simultaneously") causes regressions for some platforms.
These platforms relies on fixed mmcblk device indexes, instead of
deploying the defacto standard with UUID/PARTUUID. In other words their
rootfs needs to be available at hardcoded paths, like /dev/mmcblk0p2.
Such guarantees have never been made by the kernel, but clearly the above
commit changes the behaviour. More precisely, because of that the order
changes of how cards becomes detected, so do their corresponding mmcblk
device indexes.
As the above commit significantly improves boot time for some platforms
(magnitude of seconds), let's avoid reverting this change but instead
restore the behaviour of how mmcblk device indexes becomes picked.
By using the same index for the mmcblk device as for the corresponding mmc
host device, the probe order of mmc host devices decides the index we get
for the mmcblk device.
For those platforms that suffers from a regression, one could expect that
this updated behaviour should be sufficient to meet their expectations of
"fixed" mmcblk device indexes.
Another side effect from this change, is that the same index is used for
the mmc host device, the mmcblk device and the mmc block queue. That
should clarify their relationship.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: 520bd7a8b4 ("mmc: core: Optimize boot time by detecting cards
simultaneously")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- sdhci: Fix regression setting power on Trats2 board
- sdhci-pci: Add support and PCI IDs for more Broxton host controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J+cN
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.6 rc3:
MMC host:
- sdhci: Fix regression setting power on Trats2 board
- sdhci-pci: Add support and PCI IDs for more Broxton host controllers"
* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
mmc: sdhci: Fix regression setting power on Trats2 board
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e5 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix ABI regression of MMC BLK ioctl
- Remove the unused MMC_DATA_STREAM flag
- Enable asynchronous system PM for the host device
- Minor fixes and clean-ups
SDHCI host:
Throughout the years, the numbers of SDHCI variants have increased and so
has also the numbers of SDHCI callbacks/quirks. The purpose of these
callbacks/quirks were to enable SDHCI to deal with variant specific
requirements, but unfortunate this method didn't scale. Instead we have
ended up with a mess. Not only did the code become suboptimal but also
highly fragile.
Lately many discussions of how to move forward with SDHCI has taken place
at the MMC mailing list. Step by step, we aim to turn SDHCI's common code
into a set of library functions. This will enable for optimizations and
allow some of the existing callbacks/quirks to be removed, which also
should help to make the code less fragile.
Therefore I am also really pleased to announce that Adrian Hunter (Intel)
has volunteered to step in as the maintainer for SDHCI.
Future wise, I hope the community around SDHCI will continue to grow and
that this release cycle can be the starting point of moving SDHCI into a
better shape. As a matter of fact, already in this cycle the re-factoring
has begun, but of course there are also fixes and new features included.
Some highlights:
- sdhci-iproc: Add support for Broadcom's BCM2835 eMMC IP
- sdhci-acpi: Add support for QCOM controllers
- sdhci-pic32: Add new SDHCI variant for PIC32MZDA
Other hosts:
- atmel-mci: Fix a NULL pointer dereference
- mediatek: Add SD write-protect support
- mmc_spi: Fix card detect in GPIO case
- tmio/sdhi: Add r8a7795 support
- tmio/sdhi: Some fixes and clean-ups
- dw_mmc: Add HW reset support
- dw_mmc: Some fixes and clean-ups
- sunxi: Add support for MMC DDR52 mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MFMb
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.6' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix ABI regression of MMC BLK ioctl
- Remove the unused MMC_DATA_STREAM flag
- Enable asynchronous system PM for the host device
- Minor fixes and clean-ups
SDHCI host:
Throughout the years, the numbers of SDHCI variants have increased
and so has also the numbers of SDHCI callbacks/quirks. The purpose
of these callbacks/quirks were to enable SDHCI to deal with variant
specific requirements, but unfortunate this method didn't scale.
Instead we have ended up with a mess. Not only did the code become
suboptimal but also highly fragile.
Lately many discussions of how to move forward with SDHCI has taken
place at the MMC mailing list. Step by step, we aim to turn
SDHCI's common code into a set of library functions. This will
enable for optimizations and allow some of the existing callbacks
and quirks to be removed, which also should help to make the code
less fragile.
Therefore I am also really pleased to announce that Adrian Hunter
(Intel) has volunteered to step in as the maintainer for SDHCI.
Future wise, I hope the community around SDHCI will continue to
grow and that this release cycle can be the starting point of
moving SDHCI into a better shape. As a matter of fact, already in
this cycle the re-factoring has begun, but of course there are also
fixes and new features included. Some highlights:
- sdhci-iproc: Add support for Broadcom's BCM2835 eMMC IP
- sdhci-acpi: Add support for QCOM controllers
- sdhci-pic32: Add new SDHCI variant for PIC32MZDA
Other hosts:
- atmel-mci: Fix a NULL pointer dereference
- mediatek: Add SD write-protect support
- mmc_spi: Fix card detect in GPIO case
- tmio/sdhi: Add r8a7795 support
- tmio/sdhi: Some fixes and clean-ups
- dw_mmc: Add HW reset support
- dw_mmc: Some fixes and clean-ups
- sunxi: Add support for MMC DDR52 mode"
* tag 'mmc-v4.6' of git://git.linaro.org/people/ulf.hansson/mmc: (123 commits)
mmc: sdhci-of-at91: fix wake-up issue when using runtime pm
mmc: sdhci-pci: Do not set DMA mask in enable_dma()
mmc: sdhci-acpi: Remove enable_dma() hook
mmc: sdhci: Set DMA mask when adding host
mmc: block: fix ABI regression of mmc_blk_ioctl
mmc: atmel-mci: Check pdata for NULL before dereferencing it at DMA config
mmc: core: remove redundant memset of sdio_read_cccr
mmc: core: remove redundant memset of mmc_decode_cid
mmc: of_mmc_spi: fix unused warning
mmc: sdhci-of-arasan: add phy support for sdhci-of-arasan
mmc: sdhci-of-arasan: fix missing sdhci_pltfm_free for err handling
mmc: sdhci-of-arasan: remove disable clk_ahb from sdhci_arasan_resume
Documentation: bindings: add description of phy for sdhci-of-arasan
mmc: sdhci: Fix override of timeout clk wrt max_busy_timeout
mmc: mmci: Remove unnecessary header file
mmc: sdhci-acpi: add QCOM controllers
mmc: tegra: implement memcomp pad calibration
mmc: mediatek: Use mmc_regulator_set_vqmmc in start_signal_voltage_switch
mmc: mediatek: Change signal voltage error to dev_dbg()
mmc: sh_mmcif, tmio: Use ARCH_RENESAS
...
It is impossible to wake-up on card detect event because when sdhci
controller is runtime suspended, it is assumed that all clocks are
disabled so we can't get irqs.
If the device is removable and there is no gpio to manage the card
detection then polling is used. It doesn't mean card detection is broken.
It is curently we only way to wake-up on card event if using runtime pm.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DMA mask will already be set by sdhci_set_dma_mask(), which
is equivalent to the removed code since pci_set_dma_mask()
expands to its DMA-API counterpart.
There should also be no reason to set the DMA mask after probe.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This hook was solely used to set the DMA mask, which is now done
by the newly-added sdhci_set_dma_mask() function.
The use of a flag to ensure the mask is only set once is a strong hint
that it should not have been done there anyway.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the DMA mask in sdhci_add_host() after we determined the
capabilities of the device. 64-bit devices in particular are given the
proper mask that ensures bounce buffers are not used.
Also disable DMA if no proper DMA mask can be set, as the DMA-API
documentation specifies.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8z8ACgkQMUfUDdst+ym1vwCgnOOCORaZyeQ4QrcxPAK5pHFn
VrMAoNHvDgNYtG+Hmzv25Lgp3HnysPin
=MLRG
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (220 commits)
serial: 8250: describe CONFIG_SERIAL_8250_RSA
serial: samsung: optimize UART rx fifo access routine
serial: pl011: add mark/space parity support
serial: sa1100: make sa1100_register_uart_fns a function
tty: serial: 8250: add MOXA Smartio MUE boards support
serial: 8250: convert drivers to use up_to_u8250p()
serial: 8250/mediatek: fix building with SERIAL_8250=m
serial: 8250/ingenic: fix building with SERIAL_8250=m
serial: 8250/uniphier: fix modular build
Revert "drivers/tty/serial: make 8250/8250_ingenic.c explicitly non-modular"
Revert "drivers/tty/serial: make 8250/8250_mtk.c explicitly non-modular"
serial: mvebu-uart: initial support for Armada-3700 serial port
serial: mctrl_gpio: Add missing module license
serial: ifx6x60: avoid uninitialized variable use
tty/serial: at91: fix bad offset for UART timeout register
tty/serial: at91: restore dynamic driver binding
serial: 8250: Add hardware dependency to RT288X option
TTY, devpts: document pty count limiting
tty: goldfish: support platform_device with id -1
drivers: tty: goldfish: Add device tree bindings
...
If mmc_blk_ioctl returns -EINVAL, blkdev_ioctl continues to
work without returning err to user-space. But now we check
CAP_SYS_RAWIO firstly, so we return -EPERM to blkdev_ioctl,
which make blkdev_ioctl return -EPERM to user-space directly.
So this will break all the ioctl with BLKROSET. Now we find
Android-adb suffer it for the following log:
remount of /system failed;
couldn't make block device writable: Operation not permitted
openat(AT_FDCWD, "/dev/block/platform/ff420000.dwmmc/by-name/system", O_RDONLY) = 3
ioctl(3, BLKROSET, 0) = -1 EPERM (Operation not permitted)
Fixes: a5f5774c55 ("mmc: block: Add new ioctl to send multi commands")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using an at91sam9g20ek development board with DTS configuration may trigger
a kernel panic because of a NULL pointer dereference exception, while
configuring DMA. Let's fix this by adding a check for pdata before
dereferencing it.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When initializing sdio card, we get struct mmc_card
from mmc_alloc_card which allocates it by kzalloc. So we
don't need another memset while reading cccr.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When initializing sd or sdio card, we get struct mmc_card
from mmc_alloc_card which allocates it by kzalloc. So we don't
need another memset while decoding cid.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/of_mmc_spi.c: In function 'mmc_spi_get_pdata':
drivers/mmc/host/of_mmc_spi.c:77:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret = -EINVAL;
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds Generic PHY access for sdhci-of-arasan. Driver
can get PHY handler from dt-binding, and power-on/init the PHY.
Currently, it's just mandatory for arasan,sdhci-5.1.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, some err handling of sdhci_arasan_probe return directly
without calling sdhci_pltfm_free. This patch fixes them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't really need disable clk_ahb when failing to resume. Otherwise
we may take risk of bus error for accessing register without clk_ahb.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Normally the timeout clock frequency is read from the capabilities
register. It is also possible to set the value prior to calling
sdhci_add_host() in which case that value will override the
capabilities register value. However that was being done after
calculating max_busy_timeout so that max_busy_timeout was being
calculated using the wrong value of timeout_clk.
Fix that by moving the override before max_busy_timeout is
calculated.
The result is that the max_busy_timeout and max_discard
increase for BSW devices so that, for example, the time for
mkfs.ext4 on a 64GB eMMC drops from about 1 minute 40 seconds
to about 20 seconds.
Note, in the future, the capabilities setting will be tidied up
and this override won't be used anymore. However this fix is
needed for stable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The header file asm/sizes.h is unnecessary, let's remove it.
This also allows to compile under X86 arch.
Signed-off-by: Wang Hongcheng <annie.wang@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds the HIDs for Qualcomm Technologies Inc SDHC
controllers:
QCOM8051: non-removable device that does not support 1.8v
QCOM8052: non-removable device that does support 1.8v
Signed-off-by: Philip Elcan <pelcan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Tegra30+ SDMMC module has memcomp pads that are used to
automatically find and set the correct drive strength settings to
the sdmmc pads. The calibration needs to be manually kicked off
when the card signal voltage is changed, after the card clock is
supplied again.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased to fix a trivial compile error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've introduced a new helper in the MMC core:
mmc_regulator_set_vqmmc(). Let's use this in mtk-sd. Using this new
helper has some advantages:
1. We get the mmc_regulator_set_vqmmc() behavior of trying to match
VQMMC and VMMC when the signal voltage is 3.3V. This ensures max
compatibility.
2. We get rid of a few more warnings when probing unsupported
voltages.
3. We get rid of some non-mediatek specific code in mtk-sd.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit ceae98f20e ("mmc: core: Try other signal levels
during power up") we can see that there are times when it's
valid to try several signal voltages. Don't print an ugly
error in the logs when that happens.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new code to do the clock rate setting externally to the SDMMC
module has a shortcut to not propagate changes with a 0 rate to
the CAR by simply bailing out. This breaks proper cutting of the
card clock. Fix it by directly calling the correct sdhci function.
Fixes: a8e326a911 "mmc: tegra: implement module external clock change"
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD card support for Tegra114 started failing after commit a8e326a911
("mmc: tegra: implement module external clock change") was merged. This
commit was part of a series to enable UHS-I modes for Tegra. To
workaround this problem for now, disable UHS-I modes for Tegra114 by
separating the soc data structures for Tegra114 and Tegra124 so that
UHS-I is still enabled for Tegra124 but not Tegra114.
Fixes: a8e326a911 ("mmc: tegra: implement module external clock change")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now all clients migration to use sdhci_pltfm_init for private
allocation is done and there's no users of the priv variable, so we can
remove it from the sdhci_pltfm_host structure.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_init() function has initialized the priv member as
NULL, so there's no need to do it again.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-tegra
to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-st
to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-pxav3
to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-esdhc driver to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-at91 driver to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-arasan driver to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_unregister() could operate host's registers, it will cause
problems if the clk is already disabled and unprepared. Fix this issue
by moving the clk_disable_unprepare() call to the end of remove
function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-msm
to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There's no need to allocate one sdhci_msm_pdata for each sdhci_msm_host.
This patch removes the sdhci_msm_pdata member from sdhci_msm_host and
uses one static global sdhci_msm_pdata for all sdhci msm hosts. It also
marks sdhci_msm_ops as const.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the sdhci
esdhc-imx driver to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-bcm2835
to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use mmc core layer's API to support sd write protect
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Registers are 64bit apart, so we refactor bus_shift handling a little and set
it based on the DT compatible. Also, EXT_ACC is different. It has been tested
on a Salvator-X (Gen3) and, to check for regressions, on a Lager (Gen2).
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Further simplify the code in sdhci_prepare_data() - we don't set
SDHCI_REQ_USE_DMA anywhere else in the driver, so there is no
need to set it, and then immediately test it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rather than scanning the scatterlist multiple times for each quirk,
scan it once, checking for each possible quirk. This should be
cheaper due to the length and offset members commonly sharing the
same cache line than scanning the scatterlist multiple times.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Prepare to consolidate the DMA address/size quirk handling into one
single loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The patch "mmc: sdhci: plug DMA mapping leak on error" added
un-mapping logic to sdhci_tasklet_finish() where it is always
called, thereby preventing the mapping leaking.
Consequently the un-mapping code in sdhci_finish_data() is no
longer needed. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Split from original "mmc: sdhci: plug DMA mapping leak on error" patch ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit d31911b937 ("mmc: sdhci: fix dma memory leak in sdhci_pre_req()")
added a complicated method to manage the DMA map state for the data
transfer, but this complexity is not required.
There are three states:
* Unmapped
* Mapped by sdhci_pre_req()
* Mapped by sdhci_prepare_data()
sdhci_prepare_data() needs to know when the data buffers have been
successfully mapped by sdhci_pre_req(), and if so, there is no need to
map them a second time.
When we come to tear down the mapping, we want to know whether
sdhci_post_req() will be called (which is determined by sdhci_pre_req()
having been previously called) so that we can postpone the unmap
operation.
Hence, it makes sense to simply record when the successful DMA map
happened (via COOKIE_PRE_MAPPED vs COOKIE_MAPPED) rather than having
the complex mechanics involving COOKIE_MAPPED vs COOKIE_GIVEN.
If a mapping is created by sdhci_prepare_data(), we must tear it down
ourselves, without waiting for sdhci_post_req() (hence, the new
COOKIE_MAPPED case). If the mapping is created by sdhci_pre_req()
then sdhci_post_req() is responsible for tearing the mapping down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the host cookie indicates that the data buffers of a request are
mapped at sdhci_post_req() time, always unmap the data buffers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass the desired cookie for a successful map. This is in preparation to
clean up the MAPPED/GIVEN states.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdhci_prepare_data(), when SDHCI_REQ_USE_DMA is set, there are two
paths that prepare the data buffers for transfer. One is when
SDHCI_USE_ADMA is set, and is located inside sdhci_adma_table_pre().
The other is when SDHCI_USE_ADMA is clear, in the else clause of the
above.
Factor out the call to sdhci_pre_dma_transfer() along with its error
checking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move sdhci_pre_dma_transfer() to avoid needing to declare this function
before use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_finish_data() has two paths which result in identical DMA cleanup.
One is when SDHCI_USE_ADMA is clear, and the other is just before when
SDHCI_USE_ADMA is set, and is performed within sdhci_adma_table_post().
Simplify the code by removing the 'else' and eliminating the duplicate
inside sdhci_adma_table_post().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we are writing data to the card, there is no point in walking the
scatterlist to find out if there are any unaligned entries; this is a
needless waste of CPU cycles. Avoid this by checking for a non-read
tranfer first.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allocate both the alignment and DMA descriptor buffers together. The
size of the alignment buffer will always be aligned to the hosts
required alignment, which gives appropriate alignment to the DMA
descriptors.
We have a maximum of 128 segments, and a maximum alignment of 64 bits.
This gives a maximum alignment buffer size of 1024 bytes.
The DMA descriptors are a maximum of 12 bytes, and we allocate 128 * 2
+ 1 of these, which gives a maximum DMA descriptor buffer size of 3084
bytes.
This means the allocation for a 4K page sized system will be an order-1
allocation, since the resulting overall size is 4108. This is more
prone to failure than page-sized allocations, but since this allocation
commonly occurs at startup, the chances of failure are small.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Changed to check ADMA table alignment ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The calculation for the timeout based on the number of card clocks is
incorrect. The calculation assumed:
timeout in microseconds = clock cycles / clock in Hz
which is clearly a several orders of magnitude wrong. Fix this by
multiplying the clock cycles by 1000000 prior to dividing by the Hz
based clock. Also, as per part 1, ensure that the division rounds
up.
As this needs 64-bit math via do_div(), avoid it if the clock cycles
is zero.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.15+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data timeout gives the minimum amount of time that should be
waited before timing out if no data is received from the card.
Simply dividing the nanosecond part by 1000 does not give this
required guarantee, since such a division rounds down. Use
DIV_ROUND_UP() to give the desired timeout.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.15+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_post_req() exists to unmap a previously mapped but already
finished request, while the next request is in progress. However, the
state of the SDHCI_REQ_USE_DMA flag depends on the last submitted
request.
This means we can end up clearing the flag due to a quirk, which then
means that sdhci_post_req() fails to unmap the DMA buffer, potentially
leading to data corruption.
We can safely ignore the SDHCI_REQ_USE_DMA here, as testing
data->host_cookie is entirely sufficient.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Re-based to apply as a separate fix ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 1140011ee9 ("mmc: sdhci-pxav3: Modify clock settings for the
SDR50 and DDR50 modes") broke any chance of the SDR50 or DDR50 modes
being used.
The commit claims that SDR50 and DDR50 require clock adjustments in
the SDIO3 Configuration register, which is located via the "conf-sdio3"
resource. However, when this resource is given, we fail to read the
host capabilities 1 register, resulting in host->caps1 being zero.
Hence, both SDHCI_SUPPORT_SDR50 and SDHCI_SUPPORT_DDR50 bits remain
zero, disabling the SDR50 and DDR50 modes.
The underlying idea in this function appears to be to read the device
capabilities, modify them, and set SDHCI_QUIRK_MISSING_CAPS to cause
our modified capabilities to be used. Implement exactly that.
Fixes: 1140011ee9 ("mmc: sdhci-pxav3: Modify clock settings for the SDR50 and DDR50 modes")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we terminate a command early, we fail to properly clean up the DMA
mappings for the data part of the request. Put this clean up to the
tasklet, which is the common path for finishing a request so we always
clean up after ourselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Split original patch so that it now contains only the fix ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Unnecessarily mapping and unmapping the align buffer for SD cards is
expensive: performance measurements on iMX6 show that this gives a hit
of 10% on hdparm buffered disk reads.
MMC/SD card IO comes from the mm/vfs which gives us page based IO, so
for this case, the align buffer is not going to be used. However, we
still map and unmap this buffer.
Eliminate this by switching the align buffer to be a DMA coherent
buffer, which needs no DMA maintenance to access the buffer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When we get a response CRC error on a command, it means that the
response we received back from the card was not correct. It does not
mean that the card did not receive the command correctly. If the
command is one which initiates a data transfer, the card can enter the
data transfer state, and start sending data.
Moreover, if the request contained a data phase, we do not clean this
up, and this results in the driver triggering DMA API debug warnings,
and also creates a race condition in the driver, between running the
finish_tasklet and the data transfer interrupts, which can trigger a
"Got data interrupt" state dump.
Fix this by handing a response CRC error slightly differently: record
the failure of the data initiating command, but allow the remainder of
the request to be processed normally. This is safe as core MMC checks
the status of all commands and data transfer phases of the request.
If the card does not initiate a data transfer, then we should time out
according to the data transfer parameters.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Fix missing parenthesis around bitwise-AND expression, and tweak subject ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When a command is started, logically it has no error. Initialise the
command's error member to zero whenever we start a command.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[ Goes with "mmc: sdhci: fix command response CRC error handling" ]
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_add_host() allows the Host Controller Capability registers
to be supplied by the calling driver by using
SDHCI_QUIRK_MISSING_CAPS, but the check for the Capabilities bit
SDHCI_CAN_64BIT doesn't use the applied value and instead reads
the Host register directly. This change uses the supplied "caps"
register instead of reading the host register.
This change will allow a calling driver to simply clear the
SDHCI_CAN_64BIT bit in "caps" to handle some cases of
SDHCI_QUIRK2_BROKEN_64_BIT_DMA.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver supports the SDHCI host controller found on a PIC32.
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
This patch make num_slots to 1 if pdata->num_slot is not
defined. Meanwhile, we need to make sure num_slots should
not larger that the supported slots
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_probe clear interrupts and disable all interrupts firstly.
While it clear interrupt again before enable some interrupts. We
can't see any reason to clear it twice here, so remove the second one.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mmc already use mmc_of_parse to get "broken-cd" property,
but it considered "broken-cd" to be a quirk in its driver. We
don't need this quirk here, and just take what we need from
mmc->caps.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch implement hw_reset function for DesignWare
MMC controller. By adding this feature, mmc blk can
do some basic recovery.
Set the following resets:
software reset – BMOD[0] for IDMAC only
DMA reset - CTRL[2]
FIFO reset - CTRL[1] bits
Program the CARD_RESET register with a value of 0 for the bit
corresponding to the card number; This programming asserts the
RST_n signal and resets the card. After a minimum of 1 ?s, de-asserts the
RST_n signal and takes the card out of reset. The application can program
a new CMD only after a minimum of 200 us
This implementation can be easily tested by cutting off->On vmmc
while doing data accessing in background to simulate that case.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the prepare_command hook from entire dw_mmc driver.
Now, almost all SoCs are using by default, except Exynos.
It seems that dwmmc controller is using unnecessary hook.
To know whether needs to set this bit or not,
add the DW_MMC_CARD_NO_USE_HOLD bit.
If some SoCs need to disable this in future, just set the
DW_MMC_CARD_NO_USE_HOLD bit.
set_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags),
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Print the error code when the tuning command fails. This allows the
reason for the failure to be reported, which aids debugging.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning is part of standard requirements for the higher speed SD
card protocols, and is not an error when this occurs. When we retry
a command due to a retune, we should not print a message to the
kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Improve mmc_of_parse_voltage()'s return values so that drivers can tell
whether a voltage-range specification was present, and whether it has
been successfully parsed, or there was an error while parsing.
We return a negative errno when parsing fails, zero if no voltage-range
specification is present, or one if a voltage-range specification is
successfully parsed.
No users need modifying as no users check the return value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Each time a driver such as sdhci-esdhc-imx is probed, we get a info
printk complaining that the DT voltage-ranges property has not been
specified.
However, the DT binding specifically says that the voltage-ranges
property is optional. That means we should not be complaining that
DT hasn't specified this property: by indicating that it's optional,
it is valid not to have the property in DT.
Silence the warning if the property is missing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rcar2 & 3 docs state that for going to and coming from the 0xff setting,
the clock must first be disabled before the DIV bits are changed.
Instead of tracking this, let's just do this unconditionally.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the indentation made the code awful to read. Fix that. Also,
introduce defines instead of magic hex values. Note that this includes
one change: We mask out know 0xff instead of 0x1ff. But 0x100 has always
been the clock enable bit. It doesn't make any sense to set it depending
on the clock calculation. Update copyright notices, too. I'll be working
on those files some more in the future.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These don't make sense anymore. Since commit 5d60e50054 ("mmc: tmio:
add new TMIO_MMC_HAVE_HIGH_REG flags"), we don't deal with a resource
here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The docs for RCar Gen2 & 3 I have access to, mention delays of 5ms after
stop and 1ms after start. Make it possible to apply these values.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the docs I have access to say that this register needs the bus busy
check.
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When compiling the driver with CONFIG_MMC_DEBUG set, I got build
warnings. They have been 'fixed' meanwhile. However, because these debug
messages look random anyhow (some duplicate information printed etc),
let's just drop them and rather re-add something consistent if that
should ever be needed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After removed the MMC_DATA_STREAM, only two flags are remained.
(MMC_DATA_READ and MMC_DATA_WRITE)
The flags of READ and WRITE can't be used together.
That's why it doesn't need to use "OR' operation.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that clock delay settings for 8 bit DDR are correct, and vqmmc
support is available, we can enable MMC_CAP_1_8V_DDR support. This
enables MMC HS-DDR at up to 52 MHz, even if signal voltage switching
is not available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allwinner's MMC controller needs to run at double the card clock rate
for 8 bit DDR transfer modes. Interestingly, this is not needed for
4 bit DDR transfers.
Different clock delays are needed for 8 bit eMMC DDR, due to the
increased module clock rate. For the A80 though, the same values for
4 bit and 8 bit are shared. The new values for the other SoCs were from
A83T user manual's "new timing mode" default values, which describes
them in clock phase, rather than delay periods. These values were used
without any modification. They may not be correct, but they work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DDR transfer modes include UHS-1 DDR50 and MMC HS-DDR (or MMC_DDR52).
Consider MMC_DDR52 when setting clock delays.
Since MMC high speed mode goes up to 52 MHz instead of 50 MHz for SD,
and this number is visible in the capability macro, increase the
clock rate upper limit to 52 MHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bus width is sometimes the actual bus width, and sometimes indices
to different arrays encoding the bus width. In my debugging case "2"
could mean 8-bit as well as 4-bit, which was extremly confusing. Let's
use the human-readable actual bus width in all places.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In linux/mmc/host.h, mmc_card_is_removable() is already defined.
There is no reason that it doesn't use.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_iproc_remove() is jsut a wrapper to sdhci_pltfm_unregister.
So use the sdhci_pltfm_unregister() for the .remove hook directly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Scott Branden from Broadcom said that the BCM2835 eMMC IP core is
very similar to IPROC and share most of the quirks. So use this driver
instead of separate one.
The sdhci-iproc contains a better workaround for the clock domain
crossing problem which doesn't need any delays. This results in a
better write performance.
Btw we get the rid of the SDHCI_CAPABILITIES hack in the sdhci_readl
function.
Suggested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch moves the definition of the MMC capabilities
from the probe function into iproc platform data. After
that we are able to add support for another platform more
easily.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I had to use the source to determine what I need to write to 'test' so
that all tests are run. Let's mention this explicitly in 'testlist'.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I don't see a reason why a host driver should depend on the card driver.
It also prevents that we can use the mmc_test driver. So, remove it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
IMO this info is only useful for developers. Most users won't need this
information, since there is not much they can do about it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When DT based probing is used but the DMA request fails, the
driver will print uninitialized stack data from the rx_req
and tx_req variables, as indicated by this warning:
drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_probe':
drivers/mmc/host/omap_hsmmc.c:2162:3: warning: 'rx_req' may be used uninitialized in this function [-Wmaybe-uninitialized]
dev_err(mmc_dev(host->mmc), "unable to obtain RX DMA engine channel %u\n", rx_req);
This removes the DMA request line number from the warning, which
is the easiest solution and won't hurt us any more as we are
planning to remove the legacy code path anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch enables sdhci-acpi devices to suspend/resume asynchronously.
This will improve system suspend/resume speed. After enabling the
sdhci-acpi devices and all their child devices to suspend/resume
asynchronously on ASUS T100TA, the system suspend-to-idle time is
reduced from 1645ms to 1089ms, and the system resume time is reduced
from 940ms to 908ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch enables mmc hosts to suspend/resume asynchronously.
This will improve system suspend/resume speed. After applying
this patch and enabling all mmc hosts' child devices to
suspend/resume asynchronously on ASUS T100TA, the system
suspend-to-idle time is reduced from 1645ms to 1107ms, and the
system resume time is reduced from 940ms to 914ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eMMC chips require 2 power supplies, vmmc for internal logic, and vqmmc
for driving output buffers. vqmmc also controls signaling voltage. Most
boards we've seen use the same regulator for both, nevertheless the 2
have different usages, and should be set separately.
This patch adds support for vqmmc regulator supply, including voltage
switching. The MMC core can use this to try different signaling voltages
for eMMC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let .set_ios() fail if mmc_regulator_set_ocr() fails to enable and set a
proper voltage for vmmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sunxi_mmc_init_host() originated from Allwinner kernel sources. The
magic numbers written to various registers was never documented.
Add comments for values found in Allwinner user manuals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RPi firmware-based clocks driver can actually disable
unused clocks, so when switching to use it we ended up losing
our MMC clock once all devices were probed.
This patch adopts the changes from 1e5a0a9a58 ("mmc: sdhci-bcm2835:
Actually enable the clock") to sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clock frequency values written to an mmc host should not be less than
the minimum clock frequency which the mmc host supports.
Signed-off-by: Yuan Juntao <juntaox.yuan@intel.com>
Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adopts the changes from 475c9e43bf ("mmc: sdhci-bcm2835:
Clean up platform allocations if sdhci init fails") to sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Arason SD host controller supports set block count command (cmd23)
and high speed mode. This patch re-enable both of these features that
was disabled. For device that doesn't support high speed, it should
configure its capability register accordingly instead disables it
explicitly.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since v4.3+, CONFIG_REGULATOR_PBIAS should be enabled (for platforms that
have PBIAS regulator) in order for MMC1 to work.
Add a more verbose print to help enable CONFIG_REGULATOR_PBIAS for users
using a olddefconfig or a custom .config.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable assignment just before return is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This issue was detected by using the Coccinelle software.
Two pointer checks could be repeated by the sdricoh_init_mmc() function
during error handling even if the relevant properties can be determined
for the involved variables before by source code analysis.
* This implementation detail could be improved by adjustments
for jump targets according to the Linux coding style convention.
* Drop an unnecessary initialisation for the variable "mmc" then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These variables will eventually be set to an appropriate value a bit later.
* host
* iobase
* result
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Cc: linux-mmc@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 829b6962f7.
Revert this change as it causes a sysfs path to change and therefore
introduces and ABI regression. More precisely Android's vold is not being
able to access /sys/module/mmcblk/parameters/perdev_minors any more, since
the path becomes changed to: "/sys/module/mmc_block/..."
Fixes: 829b6962f7 ("mmc: block: don't use parameter prefix if built as
module")
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers may need to provide their own get_cd() mmc host op, but
currently the internals of the current op (sdhci_get_cd()) are
provided by sdhci_do_get_cd() which is also called from
sdhci_request().
To allow override of the get_cd functionality, change sdhci_request()
to call ->get_cd() instead of sdhci_do_get_cd().
Note, in the future the call to ->get_cd() will likely be removed
from sdhci_request() since most drivers don't need actually it.
However this change is being done now to facilitate a subsequent
bug fix.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the past, fixes for specific hardware devices were implemented
in sdhci using quirks. That approach is no longer accepted because
the growing number of quirks was starting to make the code difficult
to understand and maintain.
One alternative to quirks, is to allow drivers to override the default
mmc host operations. This patch makes it easy to do that, and it is
needed for a subsequent bug fix, for which separate patches are
provided.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This used to return -EFAULT, but the function above returns -EINVAL on
the same condition so let's stick to that.
The removal of error return on this path was introduced with b093410c9a
('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').
Fixes: b093410c9a ('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Grant Grundler <grundler@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the gpio driver is probed after the mmc one, the read/write gpio
and card detection one return -EPROBE_DEFER. Unfortunately, the memory
region remains requested, and upon the next probe, the probe will fail
anyway with -EBUSY.
Fix this by releasing the memory resource upon probe failure.
More broadly, this patch uses devm_*() primitives whenever possible in
the probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no checks for dma mapping errors in mmc_spi.
Tha patch fixes that and by the way it adds dma_unmap_single(ones_dma)
that was left on a failure path mmc_spi_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device power usage counter is increased by pm_runtime_get_noresume
but isn't decreased in err_add_host error path.
Fix this issue by calling pm_runtime_put_noidle() in the error path to
restore the device's power usage counter.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: f5f17813ae ("mmc: sdhci-of-at91: add PM support)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit fixing the conversion of pxamci to slot-gpio API fixed the
inverted the logic of the read-only gpio. Unfortunately, the commit was
tested on a non-inverted gpio, and not on the inverted one. And the fix
did work partially, by luck.
This is the remaining missing part of the fix, trivial but still necessary.
Fixes: Fixes: 26d49fe719 ("mmc: pxamci: fix read-only gpio detection polarity")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Tested-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Expressions of the form "tty->termios.c_*flag & FLAG"
are more clearly expressed with the termios flags macros,
I_FLAG(), C_FLAG(), O_FLAG(), and L_FLAG().
Convert treewide.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dHj5
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.5 rc1.
MMC core:
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik"
* tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: pwrseq_simple: Make reset-gpios optional to match doc
mmc: sdio_cis: fix unknown tuple for CISTPL_SDIO_STD
mmc: debugfs: correct wrong voltage value
mmc: tmio_mmc_dma: don't print invalid DMA cookie
mmc: core: Enable tuning according to the actual timing
mmc: mmci: support 8bit mode on the Nomadik
mmc: mmci: fix an ages old detection error
mmc: sd: limit SD card power limit according to cards capabilities
The DT binding doc says reset-gpios is an optional property but the code
currently bails out if it is omitted.
This is a regression since it breaks previously working device trees.
Fix it by restoring the original documented behaviour.
Fixes: ce03727586 ("mmc: pwrseq_simple: use GPIO descriptors array API")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CISTPL_SDIO_STD(0x91) is a known tuple, but sdio_cis don't define it, so
we get the warning below while probing several sdio wifi cards.
Refer to SDIO spec, it's not needed to parse the tuple, so this patch make
it a known one.
[ 4.098980] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[ 4.099033] mmc2: new ultra high speed SDR104 SDIO card at address 0001
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
mmc: atmel: get rid of struct mci_dma_data
mmc: atmel-mci: restore dma on AVR32
avr32: wire up missing syscalls
avr32: wire up accept4 syscall
As struct mci_dma_data is now only used by AVR32, it is nothing but
pointless indirection. Replace it with struct dw_dma_slave in the
AVR32 platform code and with a void pointer elsewhere.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit ecb89f2f5f ("mmc: atmel-mci: remove compat for non DT board
when requesting dma chan") broke dma on AVR32 and any other boards not
using DT. This restores a fallback mechanism for such cases.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The tmio_mmc_start_dma_{rx,tx} function functions contain debug
code that prints the dma cookie among other things. However,
in case we fall back to PIO mode for some reason, the cookie
variable is never initialized, and gcc warns about this:
In file included from ../include/linux/printk.h:277:0,
from ../include/linux/kernel.h:13,
from ../include/linux/list.h:8,
from ../include/linux/kobject.h:20,
from ../include/linux/device.h:17,
from ../drivers/mmc/host/tmio_mmc_dma.c:13:
../drivers/mmc/host/tmio_mmc_dma.c: In function 'tmio_mmc_start_dma':
../include/linux/dynamic_debug.h:86:3: warning: 'cookie' may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
../drivers/mmc/host/tmio_mmc_dma.c:128:15: note: 'cookie' was declared here
dma_cookie_t cookie;
This modifies the dev_dbg() statements so we only print the cookie
when we are already in the DMA path.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.
This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.
With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.
Cc: stable@vger.kernel.org
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 4956e10903 ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Cc: stable@vger.kernel.org
Fixes: 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik...")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD card specification allows cards to error out a SWITCH command
where the requested function in a group is not supported. The spec
provides for a set of capabilities which indicate which functions are
supported.
In the case of the power limit, requesting an unsupported power level
via the SWITCH command fails, resulting in the power level remaining at
the power-on default of 0.72W, even though the host and card may support
higher powers levels.
This has been seen with SanDisk 8GB cards, which support the default
0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host,
supporting up to 2.88W (800mA). This currently causes us to try to set
a power limit function value of '3' (2.88W) which the card errors out
on, and thereby causes the power level to remain at 0.72W rather than
the desired 1.44W.
Arrange to limit the selected current limit by the capabilities reported
by the card to avoid the SWITCH command failing. Select the highest
current limit that the host and card combination support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: a39ca6ae0a ("mmc: core: Simplify and fix for SD switch processing")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The misc control register is 32bit wide, the used readw/writew
accessors only mainipulate the low 16bit of this register. It
currently doesn't matter as all the bit changed are located in
the lower half, but together with the u32 variable used to hold
the contents of the register it is seriously confusing.
Switch to 32bit accessors to avoid any future breakage.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Keep the quirk bits, as Tegra30 and Tegra114 host have different levels
of support for UHS-I modes and so need different spare bits to be set,
but change the logic to be positive.
Tegra210 needs a different tuning sequence than Tegra30+. Disable
UHS modes until support for this is properly added.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the UHS tuning sequence in a similar way to the one
contained in the TRM. It deviates in the way how to check if the tap
value is passing, by using the common Linux MMC function, which does
not only check for data CRC errors, but also if the received block
pattern is correct.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Tegra30 and up TRM states that this bit should always be
programmed to 0 by driver software.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow the the driver to change the clock supplied from the CAR directly,
minimizing the need to divide the clock inside the SDMMC module itself.
This allows for higher clock speeds than the default 48MHz supplied to
the module and is a prerequisite to support DDR signaling modes, where
the Tegra host needs to be run with a fixed internal divider of 2 for
data to be sampled correctly. (Tegra K1 TRM v03p chapter 29.7.1.1)
Also enable the broken preset value quirk as the preset values need to
be adapted to the changed clocking. While Tegra114+ allows this through
vendor registers, there is no such way for Tegra30. Takes the easy way
out and keep things consistent between the different SoC generations by
flagging the preset registers as unusable.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 52221610dd ("mmc: sdhci: Improve external VDD regulator
support"), for the VDD is supplied via external regulators, we ignore
the code to convert a VDD voltage request into one of the standard
SDHCI voltage levels, then program it in the SDHCI_POWER_CONTROL. This
brings two issues:
1. SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON quirk isn't handled properly any
more.
2. What's more, once SDHCI_POWER_ON bit is set, some controllers such
as the sdhci-pxav3 used in marvell berlin SoCs require the voltage
levels programming in the SDHCI_POWER_CONTROL register, even the VDD
is supplied by external regulator. So the host in marvell berlin SoCs
still works fine after the commit. However, commit 3cbc6123a9 ("mmc:
sdhci: Set SDHCI_POWER_ON with external vmmc") sets the SDHCI_POWER_ON
bit, this would make the host in marvell berlin SoCs won't work any
more with external vmmc.
This patch restores the behavior when setting VDD through external
regulator by moving the call of mmc_regulator_set_ocr() to the end
of sdhci_set_power() function.
After this patch, the sdcard on Marvell Berlin SoC boards work again.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 52221610dd ("mmc: sdhci: Improve external VDD ...")
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A card can be removed while it is runtime suspended.
Do not print an error message.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is quite common for Android devices to utilize more
then 8 partitions on internal eMMC storage.
The vanilla kernel can support this via
CONFIG_MMC_BLOCK_MINORS, however that solution caps the
system to 256 minors total, which limits the number of
mmc cards the system can support.
This patch, which has been carried for quite awhile in
the AOSP common tree, provides an alternative solution
that doesn't seem to limit the total card count. So I
wanted to submit it for consideration upstream.
This patch sets the GENHD_FL_EXT_DEVT flag, which will
allocate minor number in major 259 for partitions past
disk->minors.
It also removes the use of disk_devt to determine devidx
from md->disk. md->disk->first_minor is always initialized
from devidx and can always be used to recover it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Austin S Hemmelgarn <ahferroin7@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Colin Cross <ccross@android.com>
[jstultz: Added context to commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc workqueue is an ordered workqueue, allowing only one work to
execute per given time. As this workqueue is used for card detection, the
conseqeunce is that cards will be detected one by one waiting for each
other.
Moreover, most of the time spent during card initialization is waiting for
the card's internal firmware to be ready. From a CPU perspective this
typically means waiting for a completion variable to be kicked via an
IRQ-handler or waiting for a sleep timer to finish.
This behaviour of detecting/initializing cards is sub-optimal, especially
for SOCs having several controllers/cards.
Let's convert to use the system_freezable_wq for the mmc detect works.
This enables several works to be executed simultaneously and thus also
cards to be detected like so.
Tests on UX500, which holds two eMMC cards and an SD-card (actually also
an SDIO card, currently not detected), shows a significant improved
behaviour due to this change.
Before this change, both the eMMC cards waited for the SD card to be
initialized as its detect work entered the workqueue first. In some cases,
depending on the characteristic of the SD-card, they got delayed 1-1.5 s.
Additionally for the second eMMC, it needed to wait for the first eMMC to
be initialized which added another 120-190 ms.
Converting to the system_freezable_wq, removed these delays and made both
the eMMC cards available far earlier in the boot sequence.
Selecting the system_freezable_wq, in favour of for example the system_wq,
is because we need card detection mechanism to be disabled once userspace
are frozen during system PM. Currently the mmc core deal with this via PM
notifiers, but following patches may utilize the behaviour of the
system_freezable_wq, to simplify the use of the PM notifiers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Alan Cooper <alcooperx@gmail.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a time window between __mmc_send_status() and time_afer(),
on some eMMC chip, the timeout_ms is only 10ms, if this thread was
scheduled out during this period, then, even card has already changes
to transfer state by the result of CMD13, this part of code also treat
it to timeout error.
So, need calculate timeout first, then call __mmc_send_status(), if
already timeout and card still in programing state, then treat it to
the real timeout error.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug
print") fixed one NULL pointer dereference but unfortunately introduced
another. "data" may be NULL if this is a command timeout for a command
without any data, so we should only use it if we're actually waiting for
data.
Fixes: bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug print")
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no primary handler is specified for threaded_irq then a
default one is assigned which always returns IRQ_WAKE_THREAD.
This handler requires the IRQF_ONESHOT, because the source of
interrupt is not disabled
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there are too many error logs shown when use CMD21/CMD19 to do tune,
and it will appear at each resume time, print out so many logs to the
uart console cost too mush time. so change it to dev_dbg.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition dependency between devices. This patch
enables MMC/SD/SDIO card and SDIO function devices to suspend/resume
asynchronously. This will take advantage of multicore and improve
system suspend/resume speed. After applying this patch and enabling
all SDIO function's child devices to suspend/resume asynchronously
on ASUS T100TA, the system suspend-to-idle time is reduced from
1645ms to 1108ms, and the system resume time is reduced from 940ms
to 918ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a legacy facility to prevent runtime suspend if the
bus power is on. This is needed in cases where the power to
the card is dependent on the bus power. It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off(). These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem. In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume. So remove the check.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The version 3.00 SDHCI spec. was a bit unclear about the
required data alignment for 64-bit DMA, whereas the version
4.10 spec. uses different language and indicates that only
4-byte alignment is required rather than the 8-byte alignment
currently implemented. That make no difference to SD and EMMC
which invariably transfer data in sector-aligned blocks.
However with SDIO, it results in using more DMA descriptors
than necessary. Theoretically that slows DMA slightly although
DMA is not the limiting factor for throughput, so there is no
discernable impact on performance. Nevertheless, the driver
should follw the spec unless there is good reason not to, so
this patch corrects the alignment criterion.
There is a more complicated criterion for the DMA descriptor
table itself. However the table is allocated by dma_alloc_coherent()
which allocates pages (i.e. aligned to a page boundary).
For simplicity just check it is 8-byte aligned, but add a comment
that some Intel controllers actually require 8-byte alignment
even when using 32-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI has built-in DMA called ADMA2. ADMA2 uses a descriptor
table to define DMA scatter-gather. Each desciptor can specify
a data length up to 65536 bytes, however the length field is
only 16-bits so zero means 65536. Consequently, putting zero
when the size is zero must not be allowed. This patch fixes
one case where zero data length could be set inadvertently.
The problem happens because unaligned data gets split and the
code did not consider that the remaining aligned portion might
be zero length. That case really only happens for SDIO because
SD and eMMC cards transfer blocks that are invariably sector-
aligned. For SDIO, access to function registers is done by
data transfer (CMD53) when the register is bigger than 1 byte.
Generally registers are 4 bytes but 2-byte registers are possible.
So DMA of 4 bytes or less can happen. When 32-bit DMA is used,
the data alignment must be 4, so 4-byte transfers won't casue a
problem, but a 2-byte transfer could. However with the introduction
of 64-bit DMA, the data alignment for 64-bit DMA was made 8 bytes,
so all 4-byte transfers not on 8-byte boundaries get "split" into
a 4-byte chunk and a 0-byte chunk, thereby hitting the bug.
In fact, a closer look at the SDHCI specs indicates that only the
descriptor table requires 8-byte alignment for 64-bit DMA. That
will be dealt with in a separate patch, but the potential for a
2-byte access remains, so this fix is needed anyway.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage. However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd. Fix by passing the card's
ocr value which does not have the flag.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver may not be able to set the power correctly but that
is not a reason to BUG().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In some cases, the stronger 33 Ohm driver strength must not be used
so it is not a suitable default. Change it to the standard default
50 Ohm value.
The patch applies to v4.2+ except the file name changed. It is
drivers/mmc/host/sdhci-pci.c prior to v.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit cc4f414c88 ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode. While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch introduce a new MMC_CAP2_NO_SDIO cap used to tell the mmc
core to not send SDIO specific commands.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are no in-kernel users of the MVSDIO platform data method
(instantiating from a board file) so just delete this code and
make this a DT-only driver. We depend on OF and check that we have
an OF node in probe().
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform data struct is only used inside the MVSDIO driver,
nowhere else in the entire kernel. Move the struct into the
driver and delete the external header.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
u32 vvn;
vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
if (vvn == VENDOR_V_22)
host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
if (vvn > VENDOR_V_22)
host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}
This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Fixes: f4932cfd22 ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The atmci_convert_chksize() function is no more valid for controller
version 0x600 due to the introduction of '2 data' chunk size.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
atmel-mci-regs.h is only included in atmel-mci.c so move its content in
the driver and do some cleanup in these definitions to remove checkpatch
errors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc pm notifiers were recently reworked, but the new
code produces a lot of warnings when CONFIG_PM_SLEEP is disabled:
In file included from ../drivers/mmc/core/sdio_bus.c:27:0:
drivers/mmc/core/core.h:97:13: warning: 'mmc_register_pm_notifier' defined but not used [-Wunused-function]
The obvious solution is to add the 'inline' keyword at the
function definition, as it should be for any function defined
in a header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0e40be7c20e0 ("mmc: core: Refactor code to register the MMC PM notifier")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here we use '|=' to set the tuning-step, but before that, we should
clear the tuning-step, otherwise we could got the wrong setting.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When compiling the sh_mmcif driver for ARM64, we currently
get a harmless build warning:
../drivers/mmc/host/sh_mmcif.c: In function 'sh_mmcif_request_dma_one':
../drivers/mmc/host/sh_mmcif.c:417:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_tx :
^
../drivers/mmc/host/sh_mmcif.c:418:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_rx;
This could be worked around by adding another cast to uintptr_t, but
I decided to simplify the code a little more to avoid that. This
splits out the platform data using code into a separate function
and builds that only for CONFIG_SUPERH. This part still has a typecast
but does not need a second one. The SH platform code could be further
modified to pass a pointer directly as we do on other architectures
when we have a filter function.
The normal case is simplified further and now just calls
dma_request_slave_channel() directly without going through the
compat handling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a trivial patch which fixes printed strings split across two
or more lines in the source. I tried to grep for some error output*,
but I couldn't find it easily because it was broken across multiple
lines. This patch makes my life easier.
* in particular "Timeout waiting for hardware interrupt."
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_pwrseq_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data in the SoC description structures is static and can therefore
reside in read-only memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add runtime PM support and use runtime_force_suspend|resume() for system
PM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmalloc instead of kzalloc, as zeroing the memory isn't needed.
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turn the informative message about no vmmc/vqmmc regulator found in
debug one. There is no need to indicate that something optional is
missing. Moreover, it can bring confusion, people who doesn't know
it is optional may consider these messages as warnings or errors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
_mmc_detect_card_removed() validates that the card is removable, but when
being called via the bus_ops ->detect() callbacks, the validation is
redundant as it's already done in mmc_rescan().
Move the validation of a removable card to the mmc_detect_card_removed()
API, which is where it's applicable, to allow the blk error recovery path
to get the response a bit earlier.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of checking for "#ifdef" directly in the code, let's invent a pair
of mmc core functions to deal with register/unregister the MMC PM notifier
block. Implement stubs for these functions when CONFIG_PM_SLEEP is unset,
as in that case the PM notifiers isn't used.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.
In mmc_rescan(), the ->card_event() and the ->get_cd() callback are being
invoked without claiming the host, let's fix this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->card_event() callback may be called when re-scan is disabled and for
non-removable cards, which both cases are unnecessary.
Instead let's move the call later in mmc_rescan() where these constraints
have been validated.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver will not probe without valid DMA channels so no need to check
if they are valid when the module is removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Anytime a write operation is performed with Reliable Write flag enabled,
the eMMC device is enforced to bypass the cache and do a write to the
underling NVM device by Jedec specification; this causes a performance
penalty since write operations can't be optimized by the device cache.
In our tests, we replayed a typical mobile daily trace pattern and found
~9% overall time reduction in trace replay by using this patch. Also the
write ops within 4KB~64KB chunk size range get a 40~60% performance
improvement by using the patch (as this range of write chunks are the ones
affected by REQ_META).
This patch has been discussed in the Mobile & Embedded Linux Storage Forum
and it's the results of feedbacks from many people. We also checked with
fsdevl and f2fs mailing list developers that this change in the usage of
REQ_META is not affecting FS behavior and we got positive feedbacks.
Reporting here the feedbacks:
http://comments.gmane.org/gmane.linux.file-systems/97219http://thread.gmane.org/gmane.linux.file-systems.f2fs/3178/focus=3183
Signed-off-by: Bruce Ford <bford@micron.com>
Signed-off-by: Luca Porzio <lporzio@micron.com>
Fixes: ce39f9d17c ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/mtk-sd.c: In function ‘get_best_delay’:
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.start’ is used uninitialized in this function
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.maxlen’ is used uninitialized in this function
If delay is zero, these fields are indeed not initialized.
Let the compiler preinitialize the whole struct to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400() calls __mmc_switch() which checks the switch is
successful using CMD13 (SEND_STATUS). The problem is that it does that
using the timing settings of the previous mode. That is prone to error,
especially when switching from HS to HS400 because the timing parameters
for HS mode are tighter than the timing parameters for HS400 mode.
In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.
However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs400() can be made more
reliable by setting the host to the correct timing before sending CMD13.
This patch does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the mmc_switch_status() function in preparation for calling it
in mmc_select_hs400().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400() begins with the card and host in HS200 mode.
Therefore, any commands sent to the card should use HS200 timing.
It is incorrect to set the host to High Speed (HS) timing before
sending the switch command. Doing so is unreliable because
the timing parameters for HS mode are tighter than the timing
parameters for HS200 mode. Thus the HS timings should be set
only after the card has switched mode.
However, it is not unreasonable first to reduce the frequency to
the HS mode frequency, which should make the switch command and
subsequent CMD13 commands more reliable.
This patch does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently mmc_select_hs200() uses __mmc_switch() which checks the
success of the switch to HS200 mode using CMD13 (SEND_STATUS).
The problem is that it does that using the timing settings of legacy
mode. That is prone to error, not least because the timing parameters
for legacy mode are tighter than the timing parameters for HS200 mode.
In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.
However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs200() can be made more
reliable by setting the host to the correct timing before sending CMD13.
This patch does that.
A complication is that the caller, mmc_select_timing(), will ignore a
switch error (indicated by -EBADMSG), assume the old mode is valid
and continue, so the old timing must be restored in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit converting pxamci to slot-gpio API inverted the logic of the
read-only gpio. Fix it by inverting the logic again.
Fixes: fd546ee6a7 ("mmc: pxamci: fix card detect with slot-gpio API")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
When card is running with DDR mode, dwmmc needs to set DDR_REG bit at
UHS_REG register.
Before this patch, dwmmc controller doesn't consider this.
If this patch is not applied, CRC or other error shoulds be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to DesignWare DoC file, CardThreshold bit should be
bit[27:16].
So it's correct to use (0xFFF << 16), not (0x1FFF << 16).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "host->dms->ch" pointer is NULL here so we can't use it to print the
error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pwrseq_emmc driver does a eMMC card reset before a system reboot to
allow broken or limited ROM boot-loaders (that don't have an eMMC reset
logic) to be able to read the second stage from the eMMC.
But this has to be called before a system reboot handler and while most
of them use the priority 128, there are other restart handlers (such as
the syscon-reboot one) that use a higher priority. So, use the highest
priority to make sure that the eMMC hw is reset before a system reboot.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even if we only use one gpd, we need alloc 2 gpd and make
the gpd->next pointer to the second gpd, or may get gpd checksum
error, this was checked by hardware
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use the ios->timing directly is better
It can reflect current timing and do settings by timing
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable omap_hsmmc for Keystone 2 architecture which reuses the HSMMC
IP found on OMAP platforms.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ACPI HIDs for Intel host controllers including one
supporting HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add some macros for HCON register operations
to make code more readable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC doesn't have a standard power control register, so when
writing this register in stack we should do nothing to avoid
incorrect operation.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There's little sense in releasing the host on mmc_add_card() error
immediately after reclaiming it, so reclaim the host only in case
of success.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This algorithm will try 1 degree increments, since there's no way to tell
what resolution the underlying phase code uses. As an added bonus, doing
many tunings yields better results since some tests are run more than once
(ex: if the underlying driver uses 45 degree increments, the tuning code
will try the same angle more than once).
It will then construct a list of good phase ranges (even ranges that cross
360/0), will pick the biggest range then it will set the sample_clk to the
middle of that range.
We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time (ex 10
degrees) this will not work with the current clock phase framework (which
floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.
If a device has device specific code (like exynos) then that will still
take precedence, otherwise this new code will execute. If the device wants
to tune, but has no sample_clk defined we'll return EIO with an error
message.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've introduced a new helper in the MMC core:
mmc_regulator_set_vqmmc(). Let's use this in dw_mmc. Using this new
helper has some advantages:
1. We get the mmc_regulator_set_vqmmc() behavior of trying to match
VQMMC and VMMC when the signal voltage is 3.3V. This ensures max
compatibility.
2. We get rid of a few more warnings when probing unsupported
voltages.
3. We get rid of some non-dw_mmc specific code in dw_mmc.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds logic to the MMC core to set VQMMC. This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.
A few notes:
* When setting the signal voltage to 3.3V we do our best to make VQMMC
and VMMC match. It's been reported that this makes some old cards
happy since they were tested back in the day before UHS when VQMMC
and VMMC were provided by the same regulator. A nice side effect of
this is that we don't end up on the hairy edge of VQMMC (2.7V),
which some EEs claim is a little too close to the minimum for
comfort.
This is done in two steps. At first we try to find a VQMMC within
a 0.3V tolerance of VMMC and if this is not supported by the
supplying regulator we try to find a suitable voltage within the
whole 2.7V-3.6V area of the spec.
* The two step approach is currently necessary, as the used
regulator_set_voltage_triplet(min, target, max) uses a simple
implementation that just tries two basic steps:
regulator_set_voltage(target, max);
regulator_set_voltage(min, target);
So with only one step with 2.7-3.6V borders, if a suitable voltage
is a bit below VMMC, we would directly get the lowest 2.7V
which some boards (like Rockchips) don't like at all.
* When setting the signal voltage to 1.8V or 1.2V we aim for that
specific voltage instead of picking the lowest one in the range.
* We very purposely don't print errors in mmc_regulator_set_vqmmc().
There are cases where the MMC core will try several different
voltages and we don't want to pollute the logs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will shortly need the calculation of an ocr-bit to the actual
voltage in a second place too, so move it from mmc_regulator_set_ocr
to a common function mmc_ocrbitnum_to_vdd to make that possible.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.
Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.
To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Freescale eSDHC driver now supports both little-endian and
big-endian mode eSDHC IPs for ARM and PPC. So, MMC_SDHCI_OF_ESDHC
option needs to be reconfigured.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add another PCI ID for an Intel eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci-pci-core.c:447:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.
- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to hardware spec, validate DDR50 mode
for SDXC.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD19 tuning is also available for DDR50 mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As SD Specifications Part1 Physical Layer Specification Version
3.01 says, CMD19 tuning is available for unlocked cards in transfer
state of 1.8V signaling mode. The small difference between v3.00
and 3.01 spec means that CMD19 tuning is also available for DDR50
mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_IOC_CMD and MMC_IOC_MULTI_CMD ioctl() code currently bails on
any eMMC errors. However, in case there is any resp[] data, we
should attempt to copy resp[] back to user space. The user app
can then determine which command(s) failed in the MMC_IOC_MULTI_CMD
case AND/OR report better diagnostics in both cases.
Gwendal Grignou provided the idea and it was previously implemented
and tested on v3.18 ChromeOS kernel:
https://chromium-review.googlesource.com/#/c/299956
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hyung Taek Ryoo <hryoo@nvidia.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: David Riley <davidriley@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add MMC_TIMING_UHS_SDR12 and MMC_TIMING_UHS_SDR25
for mmc_ios_show to show the ios->timing if mmc card runs under
these two modes.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some sdio wifi modules have not been working reliable with the sunxi-mmc
host code. This turns out to be caused by starting new io-rw commands while
the card signals that it is still busy processing a previous command.
This commit adds card-busy detection to the sunxi-mmc driver which together
with recent core changes to check card-busy before starting io-rw commands
fixes the wifi reliability issues on the Cubietruck and other sunxi boards
using sdio wifi.
Reported-by: Eugene K <sigintmailru@gmail.com>
Suggested-by: Eugene K <sigintmailru@gmail.com>
Cc: Eugene K <sigintmailru@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some sdio wifi chips will not work properly if we try to start new
sdio-rw requests while the device is signalling that it is busy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a helper function to check if an opcode is a sd-io-rw-* opcode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain eMMC devices allow vendor specific device information to be read
via a sequence of vendor commands. These vendor commands must be issued
in sequence and an atomic fashion. One way to support this would be to
add an ioctl function for sending a sequence of commands to the device
atomically as proposed here. These multi commands are simple array of
the existing mmc_ioc_cmd structure.
The structure passed via the ioctl uses a __u64 type to specify the number
of commands (so that the structure is aligned on a 64-bit boundary) and a
zero length array as a header for list of commands to be issued. The
maximum number of commands that can be sent is determined by
MMC_IOC_MAX_CMDS (which defaults to 255 and should be more than
sufficient).
This based upon work by Seshagiri Holi <sholi@nvidia.com>.
Signed-off-by: Seshagiri Holi <sholi@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The simple power sequence provider sets a value for multiple GPIOs in one
go so it is better to use the API already provided by the GPIO descriptor
API instead of open coding the same logic.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_CAP_RUNTIME_RESUME support to save resume time
Drop unnecessary SDC_ARG write
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add ios->drv_type for mmc_ios_show to show the
card's driver type.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The goto is correct and the unreachable "return -EINVAL" should be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_init() will clear all irqs and set the needed irqs. So
logically sdhci_init() should be called before request irq.
If not, some irqs may be triggled and handled wrongly. Take
the following into consideration, after request irq, if
SDIO card interrupt enabled, a sd card in the sd slot will
trigger a mass of interrupt(SDHCI_INT_CARD_INT), because at
this time, the vmmc-regulator still not restore, no voltage
supply for the sd card, so the pin of data0~data3 change and
keep low, interrupt(SDHCI_INT_CARD_INT) will rise up ceaselessly.
Due to we already reguest irq, system will be busy in handling
this endless irq, can't response to other event.
So we should call sdhci_init() before request irq in sd resume.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver prints if the data width is 8-bit but it's using a
binary OR instead of a binary AND so it will always report as
"is_8bit=Y" regardless of the flags in host->mmc->caps.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The gpiod_get() function expands to gpiod_get_index() with index 0
so it's better to use it since is easier to read and more concise.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As there are no users of the __mmc_switch() API, except for the mmc core
itself, let's convert it from an exported function into an internal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.
In some code paths for SDIO, particularly related to the PM support,
mmc_power_off|up() is invoked without keeping the host claimed. Let's fix
these.
Moreover, mmc_start|stop_host() also invokes mmc_power_off|up() without
claiming the host, let's fix these as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add an entry to the sdhci_acpi_uids list to detect the SD card
reader on the Asus X205Ta laptop.
dstd table:
Device (SDHC)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "PNP0FFF") // _HID: Hardware ID
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SD Card Controller - 80860F16") // _DDN: DOS Dev
Name (_UID, 0x03) // _UID: Unique ID
Name (RDEP, Package (0x02)
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs the
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk. Without it, the
internal clock could never stabilised when changing the sd clock
frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock
Control Register to 0 before computing the new value and writing it.
It disables the internal clock which causes a reset mecanism. If we
write the new value before this reset mecanism is done, it will prevent
the stabilisation of the internal clock, so a delay is needed. This
delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is
used.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of armada_38x_quirks error, all clocks should be cleaned-up, same
as after mv_conf_mbus_windows failure.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to 'FE-2946959' erratum the clock inversion option is
needed to support slow frequencies when the card input hold time
requirement is high. This setting is not required for high speed
MMC and might cause timing violation.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
shci-pxav3 driver is enabling by default the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not
required for Armada 38x and leads to wrong clock setting in the divider.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Starting with commit 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc") MMC on omap3 stopped working
for legacy booting.
This is because legacy booting sets up some of the resource in the
platform init code, and for optional regulators always seem to
return -EPROBE_DEFER for the legacy booting.
Let's fix the issue by checking for device tree based booting for
now. Then when omap3 boots in device tree only mode, this patch
can be just reverted.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c55d7a0553.
Without reverting this commit we get "unbalanced disables for pbias_mmc_omap4"
errors on omap4430. It seems that 4430 and 4460 behave in a different way for
the PBIAS regulator registers and until that has been debugged further we
cannot rely on the regulator status registers in hardare on 4430.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21
to do tune, assume there were 10 clock phase need to try, phase 0 to
phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so
the last CMD19/CMD21 will get CRC error, host->need_retune was set and
cause mmc_retune was called, then dead loop of mmc_retune
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move pxamci to mmc slot-gpio API to fix interrupt request.
It fixes the case where the card detection is on a gpio expander, on I2C
for example on zylonite board. In this case, the card detect netsted
interrupt is called from a threaded interrupt. The request_irq() fails,
because a hard irq cannot be a nested interrupt from a threaded
interrupt (set __setup_irq()).
This was tested on zylonite and mioa701 boards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christoph Hellwig