For DMA operation, the davinci spi driver needs an event queue number.
Currently, this number is passed as a IORESOURCE_DMA. This is not
correct, as the event queue is not a DMA channel. Pass the event queue
via the platform data structure instead.
On dm355 and dm365, move the eventq assignment for spi0 out of resources
array and into platform data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850 uart pinmux arrays are not used. Remove them.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mmcsd0_pins pinmux array contains pins that are specific to the
da850 evm board (the write protect and card detect GPIO pins). Move
the array to the board file.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mcasp_pins pinmux array is specific to the da850_evm, and is
not generic. Move the array to the board file, make it static initdata,
and rename it accordingly.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_emif25_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_cpgmac_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch defines Pin Mux configuration to enable MMC/SD
and USB-OHCI on the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
AM18x/DA850/OMAP-L138 SoCs have variants that can operate
at a maximum of 456 MHz at 1.3V operating point. Also the
1.2V operating point has a variant that can support a maximum
of 375 MHz.
This patch adds three new OPPs (456 MHz, 408 MHz and 372 MHz)
to the list of DA850 OPPs.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
Because of this, we depend on the maximum speed grade information
to be provided to us in some board specific way. The board informs
the maximum speed grade information by setting the da850_max_speed
variable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add comments describing the platform data members
and per-chip-select SPI configuration structure.
Also, add some comments describing the what happens
during the driver probe.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The "clk_internal" platform data member which contols the
CLKMOD bit in Global Control Register 1 is not useful
since CLKMOD needs be set to 1 *always* to ensure master
mode operation.
Remove this platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let DMA operation be specified on a per-device basis instead
of selecting it once during probe.
A side effect of this is the need to combine the PIO and DMA buffer
txrx_bufs routine. This is good since they anyway share some common
functionality.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Do not allocate (and de-allocate) SPI DMA channels during setup
(and cleanup) for each SPI device. Instead, allocate the DMA
channels once duing probe and use them for the life time of
the driver.
This makes sense since there are dedicated DMA channels meant
for SPI use.
This also helps remove the unnecessary DMA "sync_dev" variables
being used to store DMA channel information.
Also, the "use_dma" platform variable is now eliminated since
it is possible to check if the platform supports DMA or not
based upon whether DMA resources can be found or not.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.
The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.
However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.
Fix this by starting transmit DMA always.
This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for SPI interrupt mode operation.
Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.
Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.
Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).
While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.
Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.
The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.
This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.
With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().
Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds initial support for the Hawkboard-L138 system
It is under the machine name "omapl138_hawkboard".
This system is based on the da850 davinci CPU architecture.
Information on these system may be found at http://www.hawkboard.org.
Basic support for the UART console is included in this patch.
It's tested with latest Angstrom File Systems like ramdisk
from http://alturl.com/imb45.
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a platform device definition for tnetv107x's keypad
controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes davinci architecture code that has now been rendered
useless by the previous patches in the MDIO separation series.
In addition, the earlier phy_mask definitions have been replaced with
corresponding phy_id definitions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds mdio platform devices on SoCs that have the necessary
hardware. Clock lookup entries (aliases) have also been added, so that the
MDIO and EMAC drivers can independently enable/disable a shared underlying
clock. Further, the EMAC MMR region has been split down into separate MDIO
and EMAC regions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system
on Module (SOM) under the machine name "mityomapl138". These SOMs are based
on the da850 davinci CPU architecture. Information on these SOMs may be
found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is
included in this patch.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the DaVinci NAND driver to use the
new AEMIF timing setup API to configure the NAND access
timings.
Earlier, AEMIF configuration was being done as a special
case for DM644x board, but now more boards emerge which have
capability to boot for other media (SPI flash, NOR flash) and
have the kernel access NAND flash. This means that kernel cannot
always depend on the bootloader to setup the NAND.
Also, on platforms such as da850/omap-l138, the aemif input
frequency changes as cpu frequency changes; necessiating
re-calculation of timimg values as part of cpufreq transtitions.
This patch forms the basis for adding that support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds support to configure the AEMIF interface
with supplied timing values.
Since this capability is useful both from NOR and NAND
flashes, it is provided as a new interface and in a file
of its own.
AEMIF timing configuration is required in cases:
1) Where the AEMIF clock rate can change at runtime (a side
affect of cpu frequency change).
2) Where U-Boot does not support NAND/NOR but supports other
media like SPI Flash or MMC/SD and thus does not care about
setting up the AEMIF timing for kernel to use.
3) Where U-Boot just hasn't configured the timing values and
cannot be upgraded because the box is already in the field.
Since there is now a header file for AEMIF interface, the
common (non-NAND specific) defines for AEMIF registers have
been moved from nand.h into the newly created aemif.h
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add resources, platform device and convenience registration function for DA850's second MMC/SD controller (MMCSD1).
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add LPSC id for DA850's MMCSD1 peripheral.
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The CPGMAC pin list in da850.c was incorrectly split into two MII/RMII mode
specific pin lists, while what pin group is used is a function of how the board
is wired. Copy the pin lists to board-da850-evm.c, renaming them accordingly,
and merge the two lists in da850.c into one, da850_cpgmac_pins[], representing
the CPGMAC module as a whole...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The NAND/NOR flash pin lists (da850_nand_pins/da850_nor_pins) are purely board
specific and as such shouldn't be in da850.c -- copy them to board-da850-evm.c,
renaming to da850_evm_nand_pins/da850_evm_nor_pins respectively, and merge the
two lists in da850.c into one, representing the EMIF 2.5 module as a whole,
just like we have it in da830.c...
While at it, remove the '__init' modifier from da850_evm_setup_nor_nand() as
this function is called from non '__init' code...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Keep PLL0 SYSCLK3 at a constant rate of 100MHz. This enables the AEMIF
timing to remain valid even as the PLL0 output is changed by cpufreq
driver to save power.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
davinci: dm646x EVM: Specify reserved EDMA channel/slots
davinci: da8xx/omapl EVM: Specify reserved channels/slots
davinci: support for EDMA resource sharing
davinci: edma: provide ability to detect insufficient CC info data
davinci: da8xx: sparse cleanup: remove duplicate entries in irq priorities
davinci: DM365: fixed second serial port
Davinci: tnetv107x evm board initial support
Davinci: tnetv107x initial gpio support
Davinci: tnetv107x soc support
Davinci: tnetv107x decompresser uart definitions
Davinci: generalized debug macros
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
Not all the channels and slots available on the DM646x EVM
are used by the devices on the EVM. These resources can be
used by the DSP to speed up codec operations.
This patch reserves these channels for the DSP.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The drivers on da8xx/omapl EVMs do not utilize all the channels
and slots provided by EDMA. Some of these are better utilitzed by
the DSP on the SoC for speeding up codec operations.
Reserve these channels/slots for the DSP.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Current EDMA driver is not taking care of EDMA channels/slots
which are allocated from other processor, say DSP. If a
channel/slot is allocated from DSP, the existing EDMA driver
can still allocate the same resource on ARM.
This patch enables the user to pass the channel/slots reserved
for DSP as platform data. EDMA driver scans this list during
probe and prepares a bitmap of channel/slots which can be used
on ARM side.
Trying to reserve channels by doing a 'pre-allocate' using
edma_alloc_{slot|channel}() API does not work because
1) The reservation should be done in probe() to avoid race
with other ARM side driver trying to use EDMA
2) The alloc channel API sets up the access through shadow region
0 which will be incorrect for DSP usage. It also sets up the
channel <-> queue number mapping which is not required as DSP
will likely do its own mapping anyway.
3) (minor) There is no API to allocate channels in bulk.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the EDMA driver to expect the channel
controller (CC) infomation passed on by the platform as a fixed
size (EDMA_MAX_CC) array of pointers to structures.
Doing so helps catch errors of the sort where the resource
structure has information for more channel controllers than
the number channel controller info structures defined.
Such insufficient platform data would lead to illegal memory
accesses.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently the EDMA queue to be used by for servicing ASP through
internal RAM is fixed to EDMAQ_0 and that to service internal RAM
from external RAM is fixed to EDMAQ_1.
This may not be the desirable configuration on all platforms. For
example, on DM365, queue 0 has large fifo size and is more suitable
for video transfers. Having audio and video transfers on the same
queue may lead to starvation on audio side.
platform data as defined currently passes a queue number to the driver
but that remains unused inside the driver.
Fix this by defining one queue each for ASP and RAM transfers in the
platform data and using it inside the driver.
Since EDMAQ_0 maps to 0, thats the queue that will be used if
the asp queue number is not initialized. None of the platforms
currently utilize ping-pong transfers through internal RAM so that
functionality remains unchanged too.
This patch has been tested on DM644x and OMAP-L138 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
i2s_accurate_sck switch can be used to have a better approximate
sampling frequency.
The clock is an externally visible bit clock and it is named
i2s continuous serial clock (I2S_SCK).
The trade off is between more accurate clock (fast clock)
and less accurate clock (slow clock).
The waveform will be not symmetric.
Probably it is possible to get a better algorithm for calculating
the divider, trying to keep a slower clock as possible.
This patch has been developed against the
http://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci.git
git tree and has been tested on bmx board (similar to dm365 evm, but using
uda1345 as external audio codec).
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When McBSP peripheral gets the clock from an external pin,
there are three possible chooses, MCBSP_CLKX, MCBSP_CLKR
and MCBSP_CLKS.
evm-dm365 uses MCBSP_CLKR, instead in bmx board I have a different
hardware connection and I use MCBSP_CLKS, so I have added
this possibility.
This patch has been developed against the:
http://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci.git
git tree and has been tested on bmx board (similar to dm365 evm)
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the tnetv107x gpio controller.
Key differences between davinci and tnetv107x controllers:
- register map - davinci's controller is organized into banks of 32 gpios,
tnetv107x has a single space with arrays of registers for in, out,
direction, etc.
- davinci's controller has separate set/clear registers for output, tnetv107x
has a single direct mapped register.
This patch does not yet add gpio irq support on this controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
TNETV107X is a Texas Instruments SOC that shares a number of common features
with the Davinci architecture. Some of the key differences between
traditional Davincis and this new SOC are as follow:
1. The SOCs clock architecture includes a new spread-spectrum PLL. Some
elements of the clock architecture are reused from Davinci (e.g. LPSC), but
the PLL related code is overridden using existing interfaces in "struct clk".
2. The MMR layout on this SOC is substantially different from Davinci.
Consequently, the fixed I/O map is a whole lot more convoluted (more so than
DA8xx). The net impact here is that IO_ADDRESS() will not work on this SoC,
and therefore all mappings have to be through ioremap().
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added definitions for tnetv107x uart base addresses, and modified base address
selection for kernel decompressor to check for tnetv107x machine type.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adopts a debug uart selection similar to the OMAP model. During
the boot process, the uncompress code determines the physical and virtual base
addresses of the board-specific debug uart. These addresses are then passed
on to the in-kernel debug macros through a small chunk of memory placed just
below the page tables (@0x80003ff8).
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On some platforms like DM355, the number of EDMA parameter slots available
for EDMA_SLOT_ANY usage are few. In such cases, if MMC/SD uses 16 slots
for each instance of MMC controller, then the number of slots available
for other modules will be very few.
By passing the number of EDMA slots to be used in MMC driver from platform
data, EDMA slots available for other purposes can be controlled.
Most of the platforms will not use this platform data variable. But on
DM355, as the number of EDMA resources available is limited, the number of
scatter- gather segments used inside the MMC driver can be 8 (passed as
platform data) instead of 16. On DM355, when the number of scatter-gather
segments was reduced to 8, I saw a performance difference of about
0.25-0.4 Mbytes/sec during write. Read performance variations were
negligible.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More complete AEMIF support for boards.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added PINMUX configurations for the CLKOUT0 .. CLKOUT2
functions, for boards that want to use these clocks.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Board code may want to use them.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows for a more flexible ioremap() interception based on iotable
contents.
With this patch, the ioremap() interception code can properly translate
addresses only after davinci_soc_info has been initialized. Consequently,
in soc-specific init functions, davinci_common_init() has to happen before any
ioremap() attempts. The da8xx init sequence has been suitably modified to meet
this restriction.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the pinmux implementation so as to ioremap() the pinmux
register area on first use.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch implements the following:
- interrupt initialization uses ioremap() instead of passing a virtual address
via davinci_soc_info.
- machine definitions directly point to cp_intc_init() or davinci_irq_init()
- davinci_intc_type and davinci_intc_base now get initialized in controller
specific init functions instead of davinci_common_init()
- minor fix in davinci_irq_init() to use intc_irq_num instead of
DAVINCI_N_AINTC_IRQ
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the psc and clock control code to use ioremap()ed
registers.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch eliminates IO_ADDRESS() usage for Davinci timer definitions. The
timer code has correspondingly been modified to ioremap() MMRs instead.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch replaces the jtag id base info in davinci_soc_info with a physical
address which is then ioremap()ed within common code.
This patch (in combination with a similar change for PSC) will allow us to
eliminate the SYSCFG nastiness in DA8xx code.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the gpio_base definition in davinci_soc_info to be a
physical address, which is then ioremap()ed by the gpio initialization
function.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The uart pdata array is already terminated by a zero flag field.
This patch reuses this terminator and eliminates DAVINCI_MAX_NR_UARTS
definition. This way, future platforms can have different number of uarts
initialized via davinci_serial_init().
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The earlier watchdog reset mechanism had a couple of limitations. First, it
embedded a reference to "davinci_wdt_device" inside common code. This
forced all derived platforms (da8xx and tnetv107x) to define such a device.
This also would have caused problems in including multiple socs in a single
build due to symbol redefinition.
With this patch, davinci_watchdog_reset() now takes the platform device as an
argument. The davinci_soc_info struct has been extended to include a reset
function and a watchdog platform_device. arch_reset() then uses these
elements to reset the system in a SoC specific fashion.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pinmux registers are sequential, and do not need to be enumerated out as they
currently are. This reduces code volume and keeps things simple.
If some future SoC comes up with a discontiguous register map, PINMUX() can
then be expanded with local token pasting.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch eliminates the global gpio_lock, and implements a per-controller
lock instead. This also switches to irqsave/irqrestore locks in case gpios
are manipulated in isr.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows for gpio controllers that deviate from those found on
traditional davinci socs. davinci_soc_info has an added field to indicate the
soc-specific gpio controller type. The gpio initialization code then bails
out if necessary.
More elements (tnetv107x) to be added later into enum davinci_gpio_type.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch renders the inlined gpio accessors in gpio.h independent of the
underlying controller's register layout. This is done by including three new
fields in davinci_gpio_controller to hold the addresses of the set, clear, and
in data registers.
Other changes:
1. davinci_gpio_regs structure definition moved to gpio.c. This structure is
no longer common across all davinci socs (davinci_gpio_controller is).
2. controller base address calculation code (gpio2controller()) moved to
gpio.c as this was no longer necessary for the inline implementation.
3. modified inline range checks to use davinci_soc_info.gpio_num instead of
DAVINCI_N_GPIO.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Renamed gpio types to something more sensible:
struct gpio_controller --> struct davinci_gpio_regs
struct davinci_gpio --> struct davinci_gpio_controller
gpio2controller() --> gpio2regs()
irq2controller() --> irq2regs()
This change also moves davinci_gpio_controller definition to gpio.h.
Eventually, the gpio registers structure will be moved to gpio.c and no longer
a common cross-soc definition.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The IDE platform device is registered in three different places (2 board files
for DM644x and in dm646x.c for DM646x) while both the IDE base address and the
IDE IRQ are the same for both SoCs -- therefore, the proper place for the IDE
platform seems to be in devices.c. Merge the IDE platform data and registration
code and create davinci_init_ide() in place of dm646x_init_ide()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
linux/compiler.h is required for __iomem
linux/types.h is required u32
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Extended the MUX configuration to allow use of GPIO
terminals 64..57.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently each DaVinci board file #define's its own version of the EMIFA base
addresses (all named DAVINCI_ASYNC_EMIF_*_BASE), which leads to duplication.
Move these #define's to the SoC specific headers, changing their prefixes from
'DAVINCI' to the 'DM355', 'DM644X', and 'DM646X' since all these base addresses
are SoC specific...
And while at it, rename DM646X_ASYNC_EMIF_DATA_CE0_BASE to
DM646X_ASYNC_EMIF_CS2_SPACE_BASE in order to match the DM646x datasheet.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added tnetv107x cpu type definitions and cpu identification macros.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IRQ numbers as defined for tnetv107x cp_intc.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added definitions for LPSC modules in the tnetv107x SOC
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added list of muxed pins on the tnetv107x SOC.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename da8xx_pinmux_setup() to davinci_cfg_reg_list() and promote it for use in
other SOCs that may need the ability to configure multiple pins in one shot.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current clock control code always gates the clock (PSC state Disable = 2)
on clk_disable(). Some on-chip peripherals (e.g. LCD controller on TNETV107X)
need to be put into SwRstDisable = 0 on clock disable, to maintain
hardware sanity.
This patch extends the davinci_psc_config() arguments to pass in the desired
module state instead of a boolean enable/disable. Further, clk_disable() now
checks for the PSC_SWRSTDISABLE clk flag before selecting the target state.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Host map configuration instructs the interrupt controller to route interrupt
channels to FIQ or IRQ lines. Currently, DA8xx family of devices leave these
registers at their reset-default values.
TNETV107X however does not have sane reset defaults, and therefore this
architecture needs to reconfigure the host-map such that channels 0 and 1
go to FIQ, and the remaining channels raise IRQs.
This patch adds an optional host map argument to cp_intc_init() for this.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This hushes the following warning:
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: ‘struct platform_device’
declared inside parameter list
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The da8xx/omap-l1 boards refuse to build when CONFIG_DAVINCI_MUX is undefined
because arch/arm/mach-davinci/mux.c:da8xx_pinmux_setup() is not defined.
This patch fixes this issue. This is build tested with davinci_all_defconfig
and da8xx_omapl_defconfig and boot tested on DA830 EVM.
Reported-by: Shanmuga Sundaram Mahendran <shanmuga@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
This patch adds SPI init for DM365.
It does the following
1) Initializes SPI0
2) Defines resources to be used by SPI0
3) Adds platform data for SPI0
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds "spi.h" header file that will be used by board and
architecture specific code.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace platfrom -> platform.
This is a frequent spelling bug.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove unneeded 'struct davinci_clk' wrapper around 'struct clk_lookup'
and use clkdev_add_table() to add the list of clocks in one go.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the generic Voice Codec support for the DM365 based
platforms.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Patch adds SDA and SCL pin numbers to the i2c platform data
structure for Davinci DM355 and DM6446. This at present is
used for i2c bus recovery.
TODO: Add SDA and SCL pin number information to include all
Davinci platforms such as dm355-leopard, dm365, dm646x, da8xx etc.
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the edma_noevent list is passed from platform data.
But on some architectures, there will be many EDMA channels
which will not be used at all. This patch scans all the
platform devices and then builds a list of events which are
not being used. The unused event list will be used to allocate
EDMA channels in case of EDMA_CHANNEL_ANY usage instead of the
edma_noevent being used earlier for this purpose.
This patch is based on David Brownells's suggestion at
http://article.gmane.org/gmane.linux.davinci/15176.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for TI's CDCE949 - a clock
synthesizer with 4 PLLs and 9 outputs.
It is used on DM6467 EVM. On the EVM, it generates
clocks required for VPIF, TSIF and Audio modules.
This patch adds it as part of the DaVinci clock framework.
Testing:
The various frequency outputs on Y1 have been tested using
a out-of-tree VPIF video driver supporting HD video.
The register values for Y5 frequency outputs have been
derived from TSIF driver sources in MontaVista LSP kernel,
but actual output has not been tested for lack of TSIF
driver which actually works on the latest kernel.
Signed-off-by: Nageswari Srinivasan <nageswari@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for registering for suspend-to-RAM
functionality on da850/omap-l138 SoCs.
da850 supports wakeup based on external event and RTC
alarm.
Currently only RTC alarm based wakeup is supported.
Support for wakeup based on external event will be
added as later improvements.
For scheduling an alarm event on RTC some useful code
is present in Documentation/rtc.txt
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds core power management (suspend-to-RAM)
support for DaVinci SoCs.
The code depends on the the "deepsleep" feature to suspend
the SoC and saves power by gating the input clock.
The wakeup can be based on an external event as supported
by the SoC.
Assembly code (in sleep.S) is added to aid gating DDR2
clocks. Code doing this work should not be accessing DDR2.
The assembly code is relocated to SRAM by the code in pm.c
The support has been validated on DA850/OMAP-L138 only
though the code is (hopefully) generic enough that other
SoCs supporting deepsleep feature simply requires SoC
specific code to start using this driver.
Note that all the device drivers don't support suspend/resume
still and are being worked on.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The davinci EMAC peripheral is also available on other TI
platforms -notably TI AM3517 SoC. This patch modifies the
config option and the platform structure header files so that
the driver can be reused on non-davinci platforms as well.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM6467T (T for Turbo) is a newer and faster DM6467
part from TI. The new part supports 1080p video and
has the ARM running at 495MHz. More SoC information:
http://focus.ti.com/docs/prod/folders/print/tms320dm6467t.html
Spectrum Digital, Inc has a new EVM for this part.
It is _mostly_ same as the older DM6467 EVM except
for a 33MHz crystal input and THS8200 video encoder
for 1080p support.
The meat of this patch is dedicated to initializing
the crystal frequency from EVM board file.
Additional notes:
I did consider some alternative ways to make the crystal
input board specific including - (1) having board code
initialize the crystal frequency using the first member
of soc_info->cpu_clks array (2) introducing a new ref_clk_rate
member in soc_info structure.
But, the current way seems to be the simplest and least
intruding considering that both the clock array and SoC
info structure are actually private to the SoC file. Also
the fact that davinci_common_init() initializes both the
soc_info and clocks in one go.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Leave a comment explaining the constant value of 27Mhz used
in include/mach/timex.h for all DaVinci platforms. Many of
the platforms actually run at 24MHz timer frequency (Eg.
EVMs of DM355, DM365 and OMAP-L1).
The comment also serves as a porting alert.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Create static map for internal SRAM and populate SRAM base
and size in soc_info structure to allow SRAM allocation
functions from arch/arm/mach-davinci/sram.c to work.
On DA850 SRAM is used for suspend-to-RAM implementation
in places where DDR2 cannot be accessed as its clocks are
stopped.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When suspend is supported, both cpuidle and suspend code
need to work on DDR2 registers. Instead of mapping the
DDR2 registers twice, do it once outside of cpuidle
driver and let cpuidle driver get the virtual base address
of DDR2 registers.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
psc.h contains register defines for PSC module which
need to be accessed in assembly code which helps the
DA850/OMAP-L138 SoC go to sleep. Shutting down DDR clock
using PSC is a part of the sleep procedure.
Also, the PLL related hardware definitions in clock.h are
needed in assembly code to bypass the DDR2 PLL.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The motivation behind the change is to use the same
definitions in the assembly code responsible for
suspending the SoC, a part of which is to clock gate
the DDR2 clock.
Note that the assembly code cannot invoke the C function
meant for this. The main reason being that stack in DDR2
cannot be accessed while DDR2 clock is being clock gated.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Move defintions of DDR2 controller registers to memory.h
from cpuidle.c. The motivation behind the change is to be
able to use these defintions in assembly code that puts
DDR2 in self-refresh and enables the SoC to enter suspend
state.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP-L138 adds a second SYSCFG region having useful functionality
like deep sleep, pull up/down control and SATA clock stop.
This patch makes provision for accessing registers from second
SYSCFG region in da8xx code.
Note that OMAP-L137 has a single SYSCFG region.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sentelic - fix left/right horizontal scroll mapping
Input: pmouse - move Sentelic probe down the list
Input: add compat support for sysfs and /proc capabilities output
Input: i8042 - add Dritek quirk for Acer Aspire 5610.
Input: xbox - do not use GFP_KERNEL under spinlock
Input: psmouse - fix Synaptics detection when protocol is disabled
Input: bcm5974 - report ABS_MT events
Input: davinci_keyscan - add device_enable method to platform data
Input: evdev - be less aggressive about sending SIGIO notifies
Input: atkbd - fix canceling event_work in disconnect
Input: serio - fix potential deadlock when unbinding drivers
Input: gf2k - fix &&/|| confusion in gf2k_connect()
Add a function pointer in the platform data of the DaVinci Keyscan driver
called device_enable, in order to perform board specific actions when
the device is initialized, like setup the PINMUX configuration.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (69 commits)
davinci: Initial support for Neuros OSD2 platform.
davinci: remove unused variable in arch/arm/mach-davinci/board-sffsdr.c
davinci: fix section mismatch warning in arch/arm/mach-davinci/board-dm646x-evm.c
DaVinci: DM365: Enable DaVinci RTC support for DM365 EVM
DA8xx/OMAP-L1xx: Add high speed SD/MMC capabilities
davinci: DA8XX/OMAP-L1XX: enable cpuidle and regulator in defconfig
davinci: DA850/OMAP-L138: avoid using separate initcall for initializing regulator
davinci: DA850/OMAP-L138 EVM: register for cpuidle support
davinci: DA8XX/OMAP-L1XX: add support for cpuidle driver register
davinci: add CPU idle driver
davinci: DA8XX/OMAP-L1XX: fix compiler warning
davinci: DA850/OMAP-L138: eliminate static function declaration
davinci: DA850/OMAP-L138 EVM: simplify configuration of emac in MII/RMII mode
davinci: DA850/OMAP-L138 EVM: get rid of DA850_UI_EXP config option
davinci: DA850/OMAP-L138 EVM: implement autodetect of RMII PHY
davinci: DA830/OMAP-L137 EVM: do not configure NAND on UI card when MMC/SD is selected
davinci: DA830/OMAP-L137 EVM: use runtime detection for UI card
davinci: DA830/OMAP-L137 EVM: remove ifdefs inside da830_evm_init()
davinci: DA830/OMAP-L137 EVM: fix warning with default config
davinci: Add NAND support for DA830/OMAP-L137 EVM platform
...
The existing NAND infrastructure allows the default main and
mirror bad block tables to be overridden in nand_default_bbt().
However, the davinci_nand driver does not support this. Add
that support by adding fields to the davinci driver's platform
data so platform code can pass in their own bbt's and make the
davinci_nand driver honor them.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The Neuros OSD 2.0 is the hardware component of the Neuros Open
Internet Television Platform. Hardware is very close to Ti DM644X-EVM board.
It has: DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video.
Additionaly realtime clock, IR remote control receiver,
IR Blaster based on MSP430 (firmware although is different
from used in DM644X-EVM), internal ATA-6 3.5” HDD drive
with PATA interface, two muxed red-green leds.
For more information please refer to
http://wiki.neurostechnology.com/index.php/OSD_2.0_HD
Signed-off-by: Andrey Porodko <panda@chelcom.ru>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using a device_initcall() for initializing the voltage regulator
on DA850 is not such a good idea because it gets called for all
platforms - even those who do not have a regulator implemented.
This leads to a big fat warning message during boot-up when
regulator cannot be found.
Instead, tie initialization of voltage regulator to cpufreq init.
Define a platform specific init call which in case of DA850 gets
used for initializing the regulator. On other future platforms it
can be used for other purposes.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch provides a function to help register cpuidle driver
on da8xx/omap-l1xx platforms.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds support for DaVinci cpu idle driver.
Two idle states are defined:
1. Wait for interrupt
2. Wait for interrupt and DDR self-refresh (or power down)
Some DaVinci SoCs support putting DDR in self-refresh (eg Dm644x, DM6467)
while others support putting DDR in self-refresh and power down (eg DM35x,
DA8xx).
Putting DDR (or mDDR) in power down saves more power than self-refresh.
The patch has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the function to register the MUSB platform device.
Additional compile warning fixes by Sekhar Nori.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename setup_usb() into davinci_setup_usb(). While at it:
- move its declaration from <mach/common.h> to more fitting <mach/usb.h>;
- teach it to handle values of the 'mA' parameter greater than 510 and thus
pass 1000 instead of 500 for the power switches capable of sourcing over 1 A;
- teach it to handle odd values of the 'potpgt_ms' parameter...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.
This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds basic frequency scaling support for DA850/OMAP-L138.
Currently, frequency scaling only on PLL0 is supported. No scaling of PLL1
as yet.
Peripherals like MMC/SD which have a clock input synchronous with
ARM clock will not work well since the clock will change behind their backs.
Support for notification to such devices to adjust themselves to the
new frequency will be added in later patches. Current defconfigs keep
CPUFreq disabled so it will not affect normal operation.
The OPP defintions assume clock input of 24MHz to the SoC. This is inline
with hardcoding of input frequency in the <soc>.c files. At some point
this will need to move into board dependent code as new boards appear with
a different reference clock.
Tested on OMAP-L138 EVM with ondemand governer and a shell script to
vary processor load.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a basic CPUFreq driver for DaVinci devices registering with the
kernel CPUFreq infrastructure.
Support is added for both frequency and voltage regulation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the function to register the OHCI platform device, given the root hub
related platform data passed from the board specific code. The platfrom
data provide for overriding the OHCI port power and over-current bits at
the board level.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
These are needed by the MUSB and OHCI glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin
number of LCD panel power has changed. This patch takes
care of this change. Software will support only Beta
versions of DA850/OMAP-L138 EVM.
In the process, add the missing entry for data pin 0
and remove the GPIO specific pins from da850_lcdcntl_pins
structure. EVM specific muxing for LCD is being done in the
board file now.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add RTC support for the da830/omap-l137 and da850/omap-l138
SoC's by leveraging existing the rtc-omap driver.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the Sharp LCD035Q3DG01 graphical LCD. This
requires a minor interface change to da8xx_register_lcdc()
so that the board code can pass in the platform_data which
describes the lcd controller that's to be used.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch allows Async3 clock source to be selected between PLL1 SYSCLK2
and PLL0 SYSCLK2.
Having Async3 source from PLL1 SYSCLK2 allows peripherals on that
domain to remain unaffected by frequency scaling on PLL0.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This makes it clear that JTAG ID register is part of the
SYSCFG module
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Avoid use of IO_ADDRESS() for SYSCFG module by doing an ioremap() instead.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename the DA8XX_BOOT_CFG_BASE macro to get it in line
with the public documentation for these parts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For consistency with existing code, change the name of
da8xx_init_mcasp() to da8xx_register_mcasp().
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
1) Registers the platform device for McBSP on dm365.
2) Add platform data to DM365 EVM board file.
3) Set i2c address for audio codec at DM365 EVM board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix underruns by using dma to copy 1st to sram
in a ping/pong buffer style and then copying from
the sram to the ASP. This also has the advantage
of tolerating very long interrupt latency on dma
completion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the left and right 16 bit samples to be shifted out as 1
32 bit sample.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver enables keypad support on DaVinci platforms. DM365 is the
only platform that uses this driver at the moment.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
VPIF display changes (Chaithrika)
Add platform device and resource structures. Also define a platform specific
clock setup function that can be accessed by the driver to configure the clock
and CPLD.
VPIF caputure changes (Murali)
1) Modify vpif_subdev_info to add board_info, routing information and
vpif interface configuration. Remove addr since it is part of
board_info
2) Add code to setup channel mode and input decoder path for vpif
capture driver
Also incorporated comments against version v0 of the patch series and
added a spinlock to protect writes to common registers
Tested on DM6467 on channel 0 using TVP514x. Following bootargs used
for drivers:
vpif_capture.ch0_bufsize=829440 vpif_display.ch2_bufsize=829440
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM355 platform and board setup
This has platform and board setup changes to support vpfe capture
driver for DM355 EVMs.
Tested video capture on DM355 using tvp514x
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM644x platform and board setup
This adds platform and board setup changes required to support
vpfe capture driver on DM644x
Tested video capture on DM6446 with tvp514x driver
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For best performance, codecs often setup linked triggered
transfers with a contiguous block of params, and that is when
this API is used. Setup/configuration of these parameter RAMs
is most efficient if they are contiguous.
There is an API to allocate a set of contiguous parameter RAMs and
a corresponding API to free a set of contiguous parameter RAMs
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds definitions for some DM365 IRQs that are used by
the codecs. Codecs will also use the IRQs.
Entries are being added to enable/disable IRQ's.
There is no use as such for these entires in the kernel itself.
Instead these will be used by the "linuxutils" package of the DVSDK.
For further information on IRQ muxing refer to
http://focus.ti.com/lit/ug/sprufg5a/sprufg5a.pdf
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds PINMUX entries for DM355 Display.
These will be used by the DM355 display driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Michael Williamson