We have been observing hangs, both of KVM guest vcpu tasks and more
generally, where a process that is woken doesn't properly wake up and
continue to run, but instead sticks in TASK_WAKING state. This
happens because the update of rq->wake_list in ttwu_queue_remote()
is not ordered with the update of ipi_message in
smp_muxed_ipi_message_pass(), and the reading of rq->wake_list in
scheduler_ipi() is not ordered with the reading of ipi_message in
smp_ipi_demux(). Thus it is possible for the IPI receiver not to see
the updated rq->wake_list and therefore conclude that there is nothing
for it to do.
In order to make sure that anything done before smp_send_reschedule()
is ordered before anything done in the resulting call to scheduler_ipi(),
this adds barriers in smp_muxed_message_pass() and smp_ipi_demux().
The barrier in smp_muxed_message_pass() is a full barrier to ensure that
there is a full ordering between the smp_send_reschedule() caller and
scheduler_ipi(). In smp_ipi_demux(), we use xchg() rather than
xchg_local() because xchg() includes release and acquire barriers.
Using xchg() rather than xchg_local() makes sense given that
ipi_message is not just accessed locally.
This moves the barrier between setting the message and calling the
cause_ipi() function into the individual cause_ipi implementations.
Most of them -- those that used outb, out_8 or similar -- already had
a full barrier because out_8 etc. include a sync before the MMIO
store. This adds an explicit barrier in the two remaining cases.
These changes made no measurable difference to the speed of IPIs as
measured using a simple ping-pong latency test across two CPUs on
different cores of a POWER7 machine.
The analysis of the reason why processes were not waking up properly
is due to Milton Miller.
Cc: stable@vger.kernel.org # v3.0+
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
With the four patches applied I can run a combination of all
test cases successfully at the same time:
http://ozlabs.org/~anton/junkcode/dscr_default_test.chttp://ozlabs.org/~anton/junkcode/dscr_explicit_test.chttp://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.
We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.
This was found with the following test case:
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we update the DSCR either via emulation of mtspr(DSCR) or via
a change to dscr_default in sysfs we don't update thread.dscr.
We will eventually update it at context switch time but there is
a period where thread.dscr is incorrect.
If we fork at this point we will copy the old value of thread.dscr
into the child. To avoid this, always keep thread.dscr in sync with
reality.
This issue was found with the following testcase:
http://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Writing to dscr_default in sysfs doesn't actually change the DSCR -
we rely on a context switch on each CPU to do the work. There is no
guarantee we will get a context switch in a reasonable amount of time
so fire off an IPI to force an immediate change.
This issue was found with the following test case:
http://ozlabs.org/~anton/junkcode/dscr_explicit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The CPU hotplug code for the powernv platform currently only puts
offline CPUs into nap mode if the powersave_nap variable is set.
However, HV-style KVM on this platform requires secondary CPU threads
to be offline and in nap mode. Since we know nap mode works just
fine on all POWER7 machines, and the only machines that support the
powernv platform are POWER7 machines, this changes the code to
always put offline CPUs into nap mode, regardless of powersave_nap.
Powersave_nap still controls whether or not CPUs go into nap mode
when idle, as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the handler for hypervisor decrementer interrupts is
the same as for decrementer interrupts, i.e. timer_interrupt().
This is bogus; if we ever do get a hypervisor decrementer interrupt
it won't have anything to do with the next timer event. In fact
the only time we get hypervisor decrementer interrupts is when one
is left pending on exit from a KVM guest.
When we get a hypervisor decrementer interrupt we don't need to do
anything special to clear it, since they are edge-triggered on the
transition of HDEC from 0 to -1. Thus this adds an empty handler
function for them. We don't need to have them masked when interrupts
are soft-disabled, so we use STD_EXCEPTION_HV instead of
MASKABLE_EXCEPTION_HV.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch_update_cpu_topology() should only return 1 when the topology has
actually changed, and should return 0 otherwise.
This patch fixes a potential bug where rebuild_sched_domains() would
reinitialize the sched domains even when the topology hasn't changed.
Signed-off-by: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull CIFS fixes from Steve French.
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix cifs_do_create error hadnling
cifs: print error code if smb signature verification fails
CIFS: Fix log messages in packet checking for SMB2
CIFS: Protect i_nlink from being negative
Pull networking fixes from David Miller:
1) NLA_PUT* --> nla_put_* conversion got one case wrong in
nfnetlink_log, fix from Patrick McHardy.
2) Missed error return check in ipw2100 driver, from Julia Lawall.
3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix
from Eric Dumazet.
4) SFC driver erroneously reversed src and dst when reporting filters
via ethtool.
5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in
sja1000 can platform driver, from Alexey Khoroshilov and Sven
Schmitt.
6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only
take the lock when we really need to. From Eric Dumazet.
7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso.
8) CWND reduction in TCP is done incorrectly during non-SACK recovery,
fix from Yuchung Cheng.
9) Revert netpoll change, and fix what was actually a driver specific
problem. From Amerigo Wang. This should cure bootup hangs with
netconsole some people reported.
10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page
pointer. From Ian Campbell.
11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso.
12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet.
13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this
situation. From Oliver Neukum.
14) The davinci ethernet driver triggers an OOPS on removal because it
frees an MDIO object before unregistering it. Fix from Bin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
net: qmi_wwan: add several new Gobi devices
fddi: 64 bit bug in smt_add_para()
net: ethernet: fix kernel OOPS when remove davinci_mdio module
net/xfrm/xfrm_state.c: fix error return code
net: ipv6: fix error return code
net: qmi_wwan: new device: Foxconn/Novatel E396
usbnet: fix deadlock in resume
cs89x0 : packet reception not working
netfilter: nf_conntrack: fix racy timer handling with reliable events
bnx2x: Correct the ndo_poll_controller call
bnx2x: Move netif_napi_add to the open call
ipv4: must use rcu protection while calling fib_lookup
bnx2x: fix 57840_MF pci id
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
e1000e: DoS while TSO enabled caused by link partner with small MSS
l2tp: avoid to use synchronize_rcu in tunnel free function
gianfar: fix default tx vlan offload feature flag
netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
netfilter: nfnetlink_log: fix error return code in init path
...
Gobi devices are composite, needing both the qcserial and
qmi_wwan drivers to support all functions. Re-syncing the
list of supported devices with qcserial.
Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@tempietto.lan>
The intent was to set 4 bytes of data so that's why the sp_len is set
to 4 on the next line. The cast to u_long pointer clears 8 bytes
on 64 bit arches.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@tempietto.lan>
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526c ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of two bug fixes. One is the ATOMIC problem which is now
causing a compile failure in certain situations. The other is mishandling of
PER_LINUX32 which may also cause user visible effects.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQQN+IAAoJEDeqqVYsXL0Mza8H/RZHZSk6xRkMXXnmNXeoPpQT
HH8ILKJtfzLDhsurznNUFcHvUeU0QiwAey9NXTuJ6leXa/f9nsRtE1izejGWbxId
1JQPH0VFz0913y9PtmWMfLedKuQLt3muynKyXbfkUO6jZsfbJK4XcU2rVHHDpPh7
PgbtWQmsOqqpmsR3sN3TcU/NglACCw27V4ZhHqoFfru2loyS84BcjdYRIxoMr6W8
AldXulb0RSBseOQXvDrp5XJMV7i75WYx2EM5l8YfK4rFC/kT0TMaTGfzTLjZRjMd
bgY2e/PEZhCzTK23+d4WtrtghKD+fTtWOJoAx5a1DZP/w/A8S9Lp7xzNJ7X2MD8=
=7In9
-----END PGP SIGNATURE-----
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is a set of two bug fixes. One is the ATOMIC problem which is
now causing a compile failure in certain situations. The other is
mishandling of PER_LINUX32 which may also cause user visible effects.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix personality flag check in copy_thread()
[PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
Pull s390 fixes from Martin Schwidefsky:
"A couple of s390 bug fixes for 3.5-rc4"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/32: Don't clobber personality flags on exec
s390/smp: add missing smp_store_status() for !SMP
s390/dasd: fix ioctl return value
s390: Always use "long" for ssize_t to match size_t
davinci mdio device is not unregistered from mdiobus when removing
the module, which causes BUG_ON() when free the device from mdiobus.
Calling mdiobus_unregister() before mdiobus_free() fixes the issue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize return variable before exiting on an error path.
The initial initialization of the return variable is also dropped, because
that value is never used.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Foxconn-branded Novatel E396, Gobi3k modem.
Cc: Dan Williams <dcbw@redhat.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Ben Chan <benchan@google.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A usbnet device can share a multifunction device
with a storage device. If the storage device is autoresumed
the usbnet devices also needs to be autoresumed. Allocating
memory with GFP_KERNEL can deadlock in this case.
This should go back into all kernels that have
commit 65841fd513
That is 3.5
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The RxCFG register of the CS89x0 could be configured incorrectly
(because of misplaced parentheses), resulting in the disabling
of packet reception.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing code assumes that del_timer returns true for alive conntrack
entries. However, this is not true if reliable events are enabled.
In that case, del_timer may return true for entries that were
just inserted in the dying list. Note that packets / ctnetlink may
hold references to conntrack entries that were just inserted to such
list.
This patch fixes the issue by adding an independent timer for
event delivery. This increases the size of the ecache extension.
Still we can revisit this later and use variable size extensions
to allocate this area on demand.
Tested-by: Oliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch correct poll_bnx2x (ndo_poll_controller call) which was not
functioning well with MSI-X.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c3def943c7 have added support for
new pci ids of the 57840 board, while failing to change the obsolete value
in 'pci_ids.h'.
This patch does so, allowing the probe of such devices.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tearing down a net namespace, ipv4 mr_table structures are freed
without first deactivating their timers. This can result in a crash in
run_timer_softirq.
This patch mimics the corresponding behaviour in ipv6.
Locking and synchronization seem to be adequate.
We are about to kfree mrt, so existing code should already make sure that
no other references to mrt are pending or can be created by incoming traffic.
The functions invoked here do not cause new references to mrt or other
race conditions to be created.
Invoking del_timer_sync guarantees that ipmr_expire_timer is inactive.
Both ipmr_expire_process (whose completion we may have to wait in
del_timer_sync) and mroute_clean_tables internally use mfc_unres_lock
or other synchronizations when needed, and they both only modify mrt.
Tested in Linux 3.4.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid to use synchronize_rcu in l2tp_tunnel_free because context may be
atomic.
Signed-off-by: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit -
"b852b72 gianfar: fix bug caused by
87c288c6e9aa31720b72e2bc2d665e24e1653c3e"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're hitting bug while trying to reinsert an already existing
expectation:
kernel BUG at kernel/timer.c:895!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
<IRQ>
[<ffffffffa0069563>] nf_ct_expect_related_report+0x4a0/0x57a [nf_conntrack]
[<ffffffff812d423a>] ? in4_pton+0x72/0x131
[<ffffffffa00ca69e>] ip_nat_sdp_media+0xeb/0x185 [nf_nat_sip]
[<ffffffffa00b5b9b>] set_expected_rtp_rtcp+0x32d/0x39b [nf_conntrack_sip]
[<ffffffffa00b5f15>] process_sdp+0x30c/0x3ec [nf_conntrack_sip]
[<ffffffff8103f1eb>] ? irq_exit+0x9a/0x9c
[<ffffffffa00ca738>] ? ip_nat_sdp_media+0x185/0x185 [nf_nat_sip]
We have to remove the RTP expectation if the RTCP expectation hits EBUSY
since we keep trying with other ports until we succeed.
Reported-by: Rafal Fitt <rafalf@aplusc.com.pl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.
This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
nothing too shocking or different."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
gma500: Consider CRTC initially active.
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm: Check for invalid cursor flags
drm: Initialize object type when using DRM_MODE() macro
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.
In commit bc42aabc [2]
commit bc42aabc6a
Author: Adam Jackson <ajax@redhat.com>
Date: Wed May 23 16:26:54 2012 -0400
drm/edid/quirks: ViewSonic VA2026w
Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.
All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.
Please note that this monitor only has a VGA (D-Sub) connector [1].
[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Against -net.
In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:
[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073] [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075] [<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077] [<ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080] [<ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085] [<ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088] [<ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090] [<ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095] [<ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097] [<ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100] [<ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102] [<ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240
by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:
http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpghttp://marc.info/?l=linux-netdev&m=134563282530588&w=2
So it is safe to fix be2net driver code directly.
This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull btrfs fixes from Chris Mason:
"I've split out the big send/receive update from my last pull request
and now have just the fixes in my for-linus branch. The send/recv
branch will wander over to linux-next shortly though.
The largest patches in this pull are Josef's patches to fix DIO
locking problems and his patch to fix a crash during balance. They
are both well tested.
The rest are smaller fixes that we've had queued. The last rc came
out while I was hacking new and exciting ways to recover from a
misplaced rm -rf on my dev box, so these missed rc3."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
Btrfs: fix that repair code is spuriously executed for transid failures
Btrfs: fix ordered extent leak when failing to start a transaction
Btrfs: fix a dio write regression
Btrfs: fix deadlock with freeze and sync V2
Btrfs: revert checksum error statistic which can cause a BUG()
Btrfs: remove superblock writing after fatal error
Btrfs: allow delayed refs to be merged
Btrfs: fix enospc problems when deleting a subvol
Btrfs: fix wrong mtime and ctime when creating snapshots
Btrfs: fix race in run_clustered_refs
Btrfs: don't run __tree_mod_log_free_eb on leaves
Btrfs: increase the size of the free space cache
Btrfs: barrier before waitqueue_active
Btrfs: fix deadlock in wait_for_more_refs
btrfs: fix second lock in btrfs_delete_delayed_items()
Btrfs: don't allocate a seperate csums array for direct reads
Btrfs: do not strdup non existent strings
Btrfs: do not use missing devices when showing devname
Btrfs: fix that error value is changed by mistake
Btrfs: lock extents as we map them in DIO
...
Pull watchdog fixes from Wim Van Sebroeck:
"This will fix a warning for watchdog-test.c and it will remove a
duplicate include of delay.h"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: da9052: Remove duplicate inclusion of delay.h
watchdog: fix watchdog-test.c build warning
cache_grow() can reenable irqs so the cpu (and node) can change, so ensure
that we take list_lock on the correct nodelist.
This fixes an issue with commit 072bb0aa5e ("mm: sl[au]b: add
knowledge of PFMEMALLOC reserve pages") where list_lock for the wrong
node was taken after growing the cache.
Reported-and-tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
https://bugzilla.redhat.com/show_bug.cgi?id=785375
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Paul Mackerras
