Use list_for_each_entry_safe macro for the IPv6 addr list
as IPv6 addresses can be deleted while going through the
list.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Disable listeners and disconnect all connected QPs on
a netdev interface down event. On an interface up event,
the listeners are re-enabled.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
On i40iw device close, disconnect all connected QPs by moving
them to error state; and block further QPs, PDs and CQs from
being created. Additionally, make sure all resources have been
freed before deallocating the ibdev as part of the device close.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support to allow each independent memory region to
be configured for 2MB page size in addition to 4KB
page size.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support to use physically mapped WQ's and MR's if determined
that the OS registered user-memory for the region is physically
contiguous. This feature will eliminate the need for unnecessarily
setting up and using PBL's when not required.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The SQ head is incorrectly incremented when the number
of WQEs required is greater than the number available.
The fix is to use the I40IW_RING_MOV_HEAD_BY_COUNT
macro. This checks for the SQ full condition first and
only if SQ has room for the request, then we move the
head appropriately.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The flush_code variable in i40iw_bld_terminate_hdr() is obsolete and
the check to set qp->sq_flush is unreachable. Currently flush code is
populated in setup_term_hdr() and both SQ and RQ are flushed always
as part of the tear down flow.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove unnecessary check for return code from
device_init_pestat() and change func to void.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To be consistent, use the runtime check instead of
conditional compile.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_post_send, use the actual page size instead of
encoded page size. This is to be consistent with the
rest of the file.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It is not necessary to check cm_node->iwdev in
i40iw_rem_ref_cm_node() as it can never be NULL after
a successful call out of i40iw_make_cm_node().
Signed-off-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove dead code, which isn't executed because we
return error if the data size is greater than 48 bytes.
Inline data size greater than 48 bytes isn't supported
and the maximum WQE size is 64 bytes.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some resources are consumed internally and not available to the user.
After hw is initialized, figure out how many resources are consumed
and subtract those numbers from the initial max device capability in
i40iw_query_device().
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use memcpy for inline data copy in sends
and writes instead of byte by byte copy.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If i40iw_open() fails for any reason, the LAN handler
is not being removed. Modify i40iw_deinit_device()
to always remove the handler.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When creating QPs, ensure init_attr->cap.max_recv_sge
is clipped to MAX_FRAG_COUNT.
Expose MAX_FRAG_COUNT for max_recv_sge and max_send_sge in
i40iw_query_qp().
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Reviewed-By: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Assign each CEQ vector to a different CPU when possible, then
when creating a CQ, use the vector for the CEQ id. This
allows completion work to be distributed over multiple cores.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Passed in page_size was used as encoded value for writing
the WQE and passed in value was usually 4096. This was
working out since bit 0 was 0 and implies 4KB pages,
but would not work for other page sizes.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the MAX_IRD and MAX_ORD size negotiated to the maximum
supported values.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pre-production silicon incorrectly truncates 4 bytes of the MPA
packet in UDP loopback case. Remove the workaround as it is no
longer necessary.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the parameter to disable message packing and
always enable it.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for QoS on QPs. Upon device initialization,
a map is created from user priority to queue set
handles. On QP creation, use ToS to look up the queue
set handle for use with the QP.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When creating a FWD rule using tc create also a HW counter
for this rule.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently the code supports only drop rules to possess counters,
add that ability also for fwd rules.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently when calling mlx5_add_flow_rule we accept
only one flow destination, this commit allows to pass
multiple destinations.
This change forces us to change the return structure to a more
flexible one. We introduce a flow handle (struct mlx5_flow_handle),
it holds internally the number for rules created and holds an array
where each cell points the to a flow rule.
From the consumers (of mlx5_add_flow_rule) point of view this
change is only cosmetic and requires only to change the type
of the returned value they store.
From the core point of view, we now need to use a loop when
allocating and deleting rules (e.g given to us a flow handler).
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When adding a new rule, if we can match it with compare_match_value and
flow tag we might be able to insert the rule to the same fte.
In order to do that, there must be an overlap between the actions of the
fte and the new rule.
When updating the action of an existing fte, we must tell the firmware
we are doing so.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The way we compare between two dests will need to be used in other
places in the future, so we factor out the comparison logic
between two dests into a separate function.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
An fte status becomes FS_FTE_STATUS_EXISTING only after it was
created in HW. We can use this in order to simplify the logic on
what firmware command to use. If the status isn't FS_FTE_STATUS_EXISTING
we need to create the fte, otherwise we need only to update it.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When adding a new rule to an fte, we need to hold the fte lock
until we add that rule to the fte and increase the fte ref count.
Fixes: 0c56b97503 ("net/mlx5_core: Introduce flow steering API")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add TSAR to the eswitch which will act as the vports rate limiter.
Create/Destroy TSAR on Enable/Dsiable SRIOV.
Attach/Detach vport to eswitch TSAR on Enable/Disable vport.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
TSAR (stands for Transmit Scheduling ARbiter) is a hardware component
that is responsible for selecting the next entity to serve on the
transmit path.
The arbitration defines the QoS policy between the agents connected to
the TSAR.
The TSAR is a consist two main features:
1) BW Allocation between agents:
The TSAR implements a defecit weighted round robin between the agents.
Each agent attached to the TSAR is assigned with a weight and it is
awarded transmission tokens according to this weight.
2) Rate limer per agent:
Each agent attached to the TSAR is (optionally) assigned with a rate
limit.
TSAR will not allow scheduling for an agent exceeding its defined rate
limit.
In this patch we implement the API of manipulating the TSAR.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
For the mlx5 driver to support ConnectX-5 PCIe 4.0 VFs, we add the
device ID "0x101a" to mlx5_core_pci_table.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
According to PRM async_event_mask have to be 64 bits long.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
SRQ physical address structure field should be in big-endian format.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Update struct mlx5_ifc_xrqc_bits according to last specification
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Pull x86 bugfix from Thomas Gleixner:
"A single bugfix for the recent changes related to registering the boot
cpu when this has not happened before prefill_possible_map().
The main problem with this change got fixed already, but we missed the
case where the local APIC is not yet mapped, when prefill_possible_map()
is invoked, so the registration of the boot cpu which has the APIC bit
set in CPUID will explode.
I should have seen that issue earlier, but all I can do now is feeling
embarassed"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smpboot: Init apic mapping before usage
- A regression wrt. overlayfs, introduced in -rc2.
- An UBI issue, found by Dan Carpenter's static checker.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=eOKJ
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs
Pull ubi/ubifs fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- A regression wrt overlayfs, introduced in -rc2.
- An UBI issue, found by Dan Carpenter's static checker"
* tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs:
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
We haven't seen a whole lot of fixes for the first two weeks since the merge
window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful of
smaller fixes to several platforms. The Uniphier reset controller changes
could probably have been delayed to 4.10, but they're not scary and just
plumbing up driver changes that went in during the merge window.
We're also adding another maintainer to Marvell Berlin platforms, to help
out when Sebastian is too busy. Yay teamwork!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OGbj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Here are a few small char/misc driver fixes for reported issues. The
"biggest" are two binder fixes for reported issues that have been
shipping in Android phones for a while now, the others are various fixes
for reported problems.
And there's a MAINTAINERS update for good measure.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgUz3APHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspNGgAnibp
VyUJZjQ7CDeIm2lD+Qgz/4a4AJ9xUaO6xmmmkov5QJ7LqscBmiw+jA==
=1qM6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small char/misc driver fixes for reported issues.
The "biggest" are two binder fixes for reported issues that have been
shipping in Android phones for a while now, the others are various
fixes for reported problems.
And there's a MAINTAINERS update for good measure.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
extcon: qcom-spmi-misc: Sync the extcon state on interrupt
hv: do not lose pending heartbeat vmbus packets
mei: txe: don't clean an unprocessed interrupt cause.
ANDROID: binder: Clear binder and cookie when setting handle in flat binder struct
ANDROID: binder: Add strong ref checks
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYExViEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYGwZggA
tK2vjkNsdbFGHscpOxzzMX3ck1tcTgHdFZY/0kgBW6yRm1/FnqP1JW20P2QIthI3
ax1U4m7xDzoS089UndkyHQnHd0ZaUV2htCrocih91QST6Og24atCiyvPSIR58Qbs
EpMNJhbXFVctJarUxdrsCMF0jl2AxxD9euPDhjkYiXLZ0tmdIWZXQUmafmGKviWs
EytssiPPs4fUOOymqKv3kMw2OoTmrTlSNMXpWWDguTPn5p2mDlHOwbJKlgyz8c4x
HAYM56Ad4S0bJyOtraVcPrwfB6gQ321Qs+JfPBR3YJgt1EIjzgeG+W5TYLezXYDu
h1/FnJqU6yrlos+NSIptxQ==
=KA/s
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Hfed
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains a single fix for Broadcom ARM64-based SoCs:
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYDhQ/AAoJEFBXWFqHsHzOjK8H/0BpUb5J1q+ULcJr5boRoErh
LIILJA3q0voOXjONRhOcUx8d3yVccR4AFDsMxP3fzfzDvHrNJcK0ldqMg2I/TvL9
0hUt/IDxSoQ4dCtuuMpWMATeAiUGzCebxKfg12stB+wXUALD7upBrLNP509/Vifw
O8xhPW5w5nWJ5g72QHpDQIqG0Le0Lf4lhuvPsS/hYOeL6mkGVfDTRMOduM3n3KLd
YSMj9NuG1IH9f4xKxGVcs/2ZPdNk+t0PfP/NuPIY3S0qtWwkJRQSPV314WEsxDff
pSCD/KhtkWf8VsHbOgiZUKXPQEsUuKLpqnjjkuF2Sm9KmYCgvaXfLfyX2eyyMN8=
=Xh9e
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.9:
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>
Here are two small driver core / kernfs fixes for 4.9-rc3. One makes
the Kconfig entry for DEBUG_TEST_DRIVER_REMOVE a bit more explicit that
this is a crazy thing to enable for a distro kernel (thanks for trying
Fedora!), the other resolves an issue with vim opening kernfs files
(sysfs, configfs, etc.).
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0CMPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspgv4AoJhR
YJeG57ReBKjlzAj497Z1X7QcAJ9GXcbbbxmwj2IcUln5I3uEyuPCkQ==
=pS6k
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core / kernfs fixes for 4.9-rc3.
One makes the Kconfig entry for DEBUG_TEST_DRIVER_REMOVE a bit more
explicit that this is a crazy thing to enable for a distro kernel
(thanks for trying Fedora!), the other resolves an issue with vim
opening kernfs files (sysfs, configfs, etc.)
Both have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Make Kconfig text for DEBUG_TEST_DRIVER_REMOVE stronger
kernfs: Add noop_fsync to supported kernfs_file_fops
Here are some small staging and iio driver fixes for reported issues for
4.9-rc3. Nothing major, the "largest" being a lustre fix for a sysfs
file that was obviously wrong, and had never been tested, so it was
moved to debugfs as that is where it belongs. The others are small bug
fixes for reported issues with various staging or iio drivers.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0N8PHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspB1IAmgP4
nFPbchXqe+xNl6X5P1jlyQYFAJ9f/RIpr0XPDi0Epto5YoO6cs1MDA==
=xyXG
-----END PGP SIGNATURE-----
Merge tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small staging and iio driver fixes for reported issues
for 4.9-rc3. Nothing major, the "largest" being a lustre fix for a
sysfs file that was obviously wrong, and had never been tested, so it
was moved to debugfs as that is where it belongs. The others are small
bug fixes for reported issues with various staging or iio drivers.
All have been in linux-next for a while with no reported issues"
* tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
greybus: fix a leak on error in gb_module_create()
greybus: es2: fix error return code in ap_probe()
greybus: arche-platform: Add missing of_node_put() in arche_platform_change_state()
staging: android: ion: Fix error handling in ion_query_heaps()
iio: accel: sca3000_core: avoid potentially uninitialized variable
iio:chemical:atlas-ph-sensor: Fix use of 32 bit int to hold 16 bit big endian value
staging/lustre/llite: Move unstable_stats from sysfs to debugfs
Staging: wilc1000: Fix kernel Oops on opening the device
staging: android/ion: testing the wrong variable
Staging: greybus: uart: Use gbphy_dev->dev instead of bundle->dev
Staging: greybus: gpio: Use gbphy_dev->dev instead of bundle->dev
iio: adc: ti-adc081c: Select IIO_TRIGGERED_BUFFER to prevent build errors
iio: maxim_thermocouple: Align 16 bit big endian value of raw reads
Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally the
atmel serial driver is back working properly.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0WQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwmIAoJYQ
5fdXVYgwh59wn0E4xuKWSH84AJ9bTIe3MDED9TrE1rocnLaj9wxIuw==
=os0d
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally
the atmel serial driver is back working properly.
All have been in linux-next with no reported issues"
* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
tty: serial_core: Fix serial console crash on port shutdown
tty/serial: at91: fix hardware handshake on Atmel platforms
vt: clear selection before resizing
sc16is7xx: always write state when configuring GPIO as an output
sh-sci: document R8A7743/5 support
tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
tty: limit terminal size to 4M chars
tty: serial: fsl_lpuart: Fix Tx DMA edge case
serial: 8250_lpss: enable MSI for sure
serial: core: fix console problems on uart_close
serial: 8250_uniphier: fix clearing divisor latch access bit
serial: 8250_uniphier: fix more unterminated string
serial: pch_uart: add terminate entry for dmi_system_id tables
devicetree: bindings: uart: Add new compatible string for ZynqMP
serial: xuartps: Add new compatible string for ZynqMP
serial: SERIAL_STM32 should depend on HAS_DMA
serial: stm32: Fix comparisons with undefined register
tty: vt, fix bogus division in csi_J
Here are a number of small USB driver fixes for 4.9-rc3. There is the
usual number of gadget and xhci patches in here to resolved reported
issues, as well as some usb-serial driver fixes and new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0foPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspqE4Ani3Y
N4J9W4SeXT7ilLLQoeLznUv8AJ4sm/Uy5d4syBa+TVEPuAHXort+vw==
=ICZX
-----END PGP SIGNATURE-----
Merge tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 4.9-rc3.
There is the usual number of gadget and xhci patches in here to
resolved reported issues, as well as some usb-serial driver fixes and
new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: chipidea: host: fix NULL ptr dereference during shutdown
usb: renesas_usbhs: add wait after initialization for R-Car Gen3
usb: increase ohci watchdog delay to 275 msec
usb: musb: Call pm_runtime from musb_gadget_queue
usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
usb: ehci-platform: increase EHCI_MAX_RSTS to 4
usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
USB: serial: fix potential NULL-dereference at probe
xhci: use default USB_RESUME_TIMEOUT when resuming ports.
xhci: workaround for hosts missing CAS bit
xhci: add restart quirk for Intel Wildcatpoint PCH
USB: serial: cp210x: fix tiocmget error handling
wusb: fix error return code in wusb_prf()
Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
Revert "usb: dwc2: gadget: change variable name to more meaningful"
USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
wusb: Stop using the stack for sg crypto scratch space
usb: dwc3: Fix size used in dma_free_coherent()
usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
...
Mustafa Ismail