Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.
Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:
[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71
This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f2267089ea.
That commit causes more problem than fixes. Firstly, kfree()
should be called after usb_ep_dequeue() and secondly, the way
things are, we will try to dequeue a request that has already
completed much more frequently than one which is pending.
Cc: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.17
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These changes add two new "simple" drivers, while removing the redundant
zte_ev driver (PIDs moved to option).
Included are also some minor clean ups to the xsens_mt driver, and the
enabling of further baud rates for pl2303 devices.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HsW7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.18-rc1
These changes add two new "simple" drivers, while removing the redundant
zte_ev driver (PIDs moved to option).
Included are also some minor clean ups to the xsens_mt driver, and the
enabling of further baud rates for pl2303 devices.
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the Seluxit ApS USB Serial Dongle to cp210x driver.
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added support for Ketra N1 wireless interface, which uses the
Silicon Labs' CP2104 USB to UART bridge with customized PID 8946.
Signed-off-by: Joe Savage <joe.savage@goketra.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver's handling of DMA buffers for non-aligned transfers
was kind of nuts. For IN transfers, it left the URB DMA buffer
mapped until the transfer completed, then synced it, copied the
data from the bounce buffer, then synced it again.
Instead of that, just call usb_hcd_unmap_urb_for_dma() to unmap
the buffer before starting the transfer. Then no syncing is
required when doing the copy. This should also allow handling of
other types of mappings besides just dma_map_single() ones.
Also reduce the size of the bounce buffer allocation for Isoc
endpoints to 3K, since that's the largest possible transfer size.
Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clip max_transfer_size to 65535 for host. dwc2_hc_setup_align_buf()
allocates coherent buffers with this size, and if it's too large we
can exhaust the coherent DMA pool.
Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device is stopped or suspended clock is not needed so we
can disable it for this time.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because we have not enough memory to have each TX FIFO of size at least
3072 bytes (the maximum single packet size with 3 transactions per
microframe), we create four FIFOs of lenght 1024, and four of length
3072 bytes, and assing them to endpoints dynamically according to
maxpacket size value of given endpoint.
Up to now there were initialized 16 TX FIFOs, but we use only 8 IN
endpoints, so we can split available memory for 8 FIFOs to have more
memory for each one.
It needed to do some small modifications in few places in code, because
there was assumption that TX FIFO numbers assigned to endpoints are the
same as the endpoint numbers, which is not true since we have dynamic
FIFO assigning.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print warning if FIFOs are configured in such a way that they don't fit
into the SPRAM available on the s3c hsotg module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DWC2/s3c-hsotg debug messages are really useless for typical user,
so hide them behind dev_dbg().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust the debug text to the name of the printed variable.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quite big pull request this time. Audio and UVC gadgets
can now be used with our configfs-based binding. We have
three PHY drivers being removed because a new one has been
added using new PHY framework.
Gadget framework got a new ->reset callback preparing for
some other changes to come on next merge window.
A few new drivers came in as well; among those we have a
new UDC driver from Xilinx and two new glue layers for
DWC3 (ST and Qualcomm).
DWC3 also learned about tracepoints which will help debugging
quite a bit.
Other than that, a big series of non-critical fixes and
cleanups.
All patches have been on linux-next for quite a bit of time
and I boot tested these changes on platforms I have access
to and work with mainline.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VHzN
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.18 merge window
Quite big pull request this time. Audio and UVC gadgets
can now be used with our configfs-based binding. We have
three PHY drivers being removed because a new one has been
added using new PHY framework.
Gadget framework got a new ->reset callback preparing for
some other changes to come on next merge window.
A few new drivers came in as well; among those we have a
new UDC driver from Xilinx and two new glue layers for
DWC3 (ST and Qualcomm).
DWC3 also learned about tracepoints which will help debugging
quite a bit.
Other than that, a big series of non-critical fixes and
cleanups.
All patches have been on linux-next for quite a bit of time
and I boot tested these changes on platforms I have access
to and work with mainline.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit be0a8887bb.
The original commit f2267089ea
(usb: gadget: composite: dequeue cdev->req before free it in
composite_dev_cleanup) ended up being reverted because it caused
more issues then fixed. We will also revert this counter part
commit so we start clean to properly add that idea back.
Cc: Li Jun <b47624@freescale.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
This adds a bounce buffer that handles the end of OUT requests where
req.length is not divisible by ep->ep.maxpacket.
Before this, such requests were rejected as the DMA engine cannot
restrict itself to buffers that are smaller than ep->ep.maxpacket.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The state attribute is connected to the kobj of the udc, not the gadget.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.
That will trigger a Data Abort exception because
we would try to access register while clock is gated.
Fix that bug.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 869c597 (usb: musb: dsps: add support for suspend and resume)
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the local queue variable instead of computing it every time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The struct usb_endpoint_descriptor wMaxPacketSize field the struct
usb_ss_ep_comp_descriptor wBytesPerInterval field are stored in
little-endian format. Convert the values from CPU order to little endian
before storing the values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function isn't called from outside of its compilation unit, make it
static.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces virtual endpoint address mapping. It separates
function logic form physical endpoint addresses making it more hardware
independent.
Following modifications changes user space API, so to enable them user
have to switch on the FUNCTIONFS_VIRTUAL_ADDR flag in descriptors.
Endpoints are now refered using virtual endpoint addresses chosen by
user in endpoint descpriptors. This applies to each context when endpoint
address can be used:
- when accessing endpoint files in FunctionFS filesystemi (in file name),
- in setup requests directed to specific endpoint (in wIndex field),
- in descriptors returned by FUNCTIONFS_ENDPOINT_DESC ioctl.
In endpoint file names the endpoint address number is formatted as
double-digit hexadecimal value ("ep%02x") which has few advantages -
it is easy to parse, allows to easly recognize endpoint direction basing
on its name (IN endpoint number starts with digit 8, and OUT with 0)
which can be useful for debugging purpose, and it makes easier to introduce
further features allowing to use each endpoint number in both directions
to have more endpoints available for function if hardware supports this
(for example we could have ep01 which is endpoint 1 with OUT direction,
and ep81 which is endpoint 1 with IN direction).
Physical endpoint address can be still obtained using ioctl named
FUNCTIONFS_ENDPOINT_REVMAP, but now it's not neccesary to handle
USB transactions properly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The SCSI specification requires that the second Command Data Byte
should contain the LUN value in its high-order bits if the recipient
device reports SCSI level 2 or below. Nevertheless, some USB
mass-storage devices use those bits for other purposes in
vendor-specific commands. Currently Linux has no way to send such
commands, because the SCSI stack always overwrites the LUN bits.
Testing shows that Windows 7 and XP do not store the LUN bits in the
CDB when sending commands to a USB device. This doesn't matter if the
device uses the Bulk-Only or UAS transports (which virtually all
modern USB mass-storage devices do), as these have a separate
mechanism for sending the LUN value.
Therefore this patch introduces a flag in the Scsi_Host structure to
inform the SCSI midlayer that a transport does not require the LUN
bits to be stored in the CDB, and it makes usb-storage set this flag
for all devices using the Bulk-Only transport. (UAS is handled by a
separate driver, but it doesn't really matter because no SCSI-2 or
lower device is at all likely to use UAS.)
The patch also cleans up the code responsible for storing the LUN
value by adding a bitflag to the scsi_device structure. The test for
whether to stick the LUN value in the CDB can be made when the device
is probed, and stored for future use rather than being made over and
over in the fast path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Tiziano Bacocco <tiziano.bacocco@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The zte_ev driver is based on code (once) distributed by ZTE that still
appears to originally have been reverse-engineered and bolted onto the
generic driver.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Lei Liu, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1) let's remove the redundant zte_ev driver.
Also move the remaining ZTE PIDs to the generic option modem driver.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc5' into usb-next
USB fixes in Linux 3.17-rc5 are needed to build on top of for 3.18.
Signed-off-by: Johan Hovold <johan@kernel.org>
DWC3 glue layer is hardware layer around Synopsys DesignWare
USB3 core. Its purpose is to supply Synopsys IP with required
clocks, voltages and interface it with the rest of the SoC.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The udc driver can notify the udc core that bus reset occurs by
calling this utility, the core will notify gadget driver this
information and update gadget state accordingly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Xilinx USB2 device is a soft IP which supports both full
and high speed USB 2.0 data transfers. This patch adds
xilinx usb2 device driver support.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I'm seeing problems with a d-link dwcl-g122 wifi dongle that
someone sent me. There are reports of other wifi dongles with the
same/similar problem. The devices appear to be NAKing to the point
of confusing the dwc2 driver completely.
The attached patch helps with my d-link dwl-g122 - it's adapted
from the Raspberry Pi dwc_otg driver, which is a modified version
of the Synopsys vendor driver. The error recovery is still valid
after the patch, I think.
Cc: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some late fixes for dwc3 so we have something more stable
on v3.17-final.
Most bugs have been there for quite a while and nobody
noticed, except for TRB completion when multiple TRBs
are started.
Patches were tested on AM437x SK and J6 EVM and are passing
my tests.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CdSO
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.17-rc4
Some late fixes for dwc3 so we have something more stable
on v3.17-final.
Most bugs have been there for quite a while and nobody
noticed, except for TRB completion when multiple TRBs
are started.
Patches were tested on AM437x SK and J6 EVM and are passing
my tests.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.
Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.
There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.
Reported-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci driver will OOPS on resume from S2/S3 if dma_alloc_coherent()
is out of memory. This is a result of two things:
1. xhci_mem_cleanup() in xhci-mem.c free's xhci->lpm_command if
it's not NULL, but doesn't set it to NULL after the free.
2. xhci_mem_cleanup() is called twice on resume, once for normal
restart and once from xhci_mem_init() if dma_alloc_coherent() fails,
resulting in a free of xhci->lpm_command that has already been freed.
The fix is to set xhci->lpm_command to NULL after freeing it.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci initialization fails before the roothub bandwidth
domains (xhci->rh_bw[i]) are allocated it will oops when
trying to access rh_bw members in xhci_mem_cleanup().
Reported-by: Manuel Reimer <manuel.reimer@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.
On connecting the cable a message like this appears four times in the log:
reset full speed USB device number 4 using uhci_hcd
That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8df438571c.
This patch breaks building dwc2 driver in gadget mode at samsung
platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e006fee6ec.
This patch causes build break. Modifications in Makefile and Kconfig have
no connection with driver code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though the BUG() in __ffs_event_add is a dead-code, it is still
better to warn rather then crash the system if that code ever gets
executed.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initialize USB PHY after every Link controller reset
Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY drivers keep track of the current state of the hardware,
so don't change PHY settings under it.
Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a large numbers of issues with ASM1051 devices in uas mode:
1) They do not support REPORT SUPPORTED OPERATION CODES
2) They use out of spec 8 byte status iu-s when they have no sense data,
switching to normal 16 byte status iu-s when they do have sense data.
3) They hang / crash when combined with some disks, e.g. a Crucial M500 ssd.
4) They hang / crash when stressed (through e.g. sg_reset --bus) with disks
with which then normally do work (once 1 & 2 are worked around).
Where as in BOT mode they appear to work fine, so the best way forward with
these devices is to just blacklist them for uas usage.
Unfortunately this is easier said then done. as older versions of the ASM1053
(which works fine) use the same usb-id as the ASM1051.
When connected over USB-3 the 2 can be told apart by the number of streams
they support. So this patch adds some less then pretty code to disable uas for
the ASM1051. When connected over USB-2, simply disable uas alltogether for
devices with the shared usb-id.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each core could have more than one alternative address. There are cores
with 8 alternative addresses for different functions. The PHY control
in the Chip common B core is done through the 2. alternative address
and not the first one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CC: linux-usb@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces ioctl named FUNCTIONFS_ENDPOINT_DESC, which
returns endpoint descriptor to userspace. It works only if function
is active.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add reset API at usb_gadget_driver, it calls disconnect handler currently,
but may do different things in future.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add reset API at usb_gadget_driver, it calls disconnect handler currently,
but may do different things in future.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add reset API at usb_gadget_driver, it calls disconnect handler currently,
but may do different things in future.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add reset API at usb_gadget_driver, it calls disconnect handler currently,
but may do different things in future.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need "idx" to be signed for the error handling to work.
Fixes: 6d5c1c77bb ('usb: gadget: f_fs: fix the redundant ep files problem')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Attach strings to gadget with usb_strings_attach.
It is required for correct instantiation of functions more than once:
instead of modifying the local uvc_en_us_strings a function instance
specific copy is created with usb_gstrings_attach.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no users of the old interface left. Remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new function interface of f_uvc.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new function registration interface. It is required
in order to integrate configfs support.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[Updated copyright years]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Compile uvc_queue, uvc_v4l2, uvc_video separately so that later they can
be all combined in a separately compiled f_uvc.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[Make uvc_v4l2_ioctl_ops non-static]
[Rename __UVC__V4L2__H__ and __UVC__VIDEO__H__]
[Update MAINTAINERS]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prepare for separate compilation of uvc function's components.
Some symbols will have to be exported, so rename to avoid
conflicts with functions of the same name in host uvc.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[Rename uvc_video_pump and uvc_queue_head as well]
[Rename forgotten uvc_queue_cancel instance in a comment]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The kbuild test bot generated the warning:
drivers/usb/gadget/function/f_sourcesink.c:1498: warning: comparison is
always false due to limited range of data type
This patch fixes it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move the "samsung,s3c6400-hsotg" binding as the probe function in the gadget
driver will get removed when the dual-role driver is implemented.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update DWC2 kconfig and makefile to support dual-role mode. The platform
file will always get compiled for the case where the controller is directly
connected to the CPU. So for loadable modules, only dwc2.ko is needed.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the "dr_mode", the otg controller can work as
device role and host role. Some boards always want to use host mode
and some other boards want to use gadget mode. We use the dts setting
to set dwc2's mode, rather than fixing it to whatever hardware says.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation for GNPTXFSIZ says that "For host mode, this field
is always valid." Since we're already switching to host mode for
HPTXFSIZ, let's also read GNPTXFSIZ in host mode.
On an rk3288 SoC, without this change we see this at bootup:
dwc2 ff580000.usb: gnptxfsiz=00100400
dwc2 ff580000.usb: 128 invalid for host_nperio_tx_fifo_size. Check HW configuration.
After this change we see:
dwc2 ff580000.usb: gnptxfsiz=04000400
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add compatible data for dwc2 controller found on
rk3066, rk3188 and rk3288 processors from rockchip.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we want to keep support for both older usb-phys as well as the
newer generic phys, lets first get the generic PHYs and fallback to
older USB-PHYs only when we fail to get the former.
This should fix the issue with ehci-exynos and ohci-exynos, wherein
in the absence of SAMSUNG_USB2PHY config symbol, we end up getting
the NOP_USB_XCEIV phy when the same is enabled. And thus the PHYs
are not configured properly.
Reported-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jingoo Han <jg1.han@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.
That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.
This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.
This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.
This patch should be backported to all kernels containing
commit 71c731a.
Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUDOW+AAoJEHm+PkMAQRiGOXYH/00TPKm8PdM5cXXG2YYYv9eT
W99K7KD2i0/qiVtlGgjjvB7fO3K0HcZusTd2jmVd8IWntXvauq7Zpw5YZkjwu4KX
Y1HCwwCd2aw0FoqgrJhNP3+j5Cr1BD/HLtbffjCe+A3tppOIis4Bwt2wJOoYlXpS
hU9Jxxc4lcRo8YKbffouDo7PIneWeJy8N+WGpUR5BfJIEK0ZZtCUqn3/3WLX4FYu
fE6uiF/bACTpKXU/mo4dDbhZp439H/QdwQc9B0F8+8CBDMXKaNHrPV7kN36T2SWa
fD4boikTsi/yh9Ks1fvHbvNq2N0ihoMnja+vLRyvjAcAQv2fKG3OZtYgFWSdghU=
=Xknd
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc4' into next
Merge Linux 3.17-rc4 here so we have all the latest
fixes on next too. This also cleans up a few conflicts
when applying patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/Makefile
drivers/usb/gadget/function/Makefile
drivers/usb/gadget/legacy/Makefile
drivers/usb/phy/phy-samsung-usb.h
When configfs support is integrated the future uvc function
module must not take any parameters. Move parameters to
webcam.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Simplify ioctl handling by using video_ioctl2.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To handle class requests received on ep0, the driver needs to access the
length and direction of the request after the setup stage. It currently
stores them in a v4l2 event during the setup stage, and then copies them
from the event structure to the driver internal state structure when the
event is dequeued.
This two-steps approach isn't necessary. Simplify the driver by storing
the needed information in the driver internal state structure directly
during the setup stage.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This driver supports other SoCs, but they need boards/Soc depend code.
So, this patch adds device tree support for R-Car H2 and M2 initially.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Intensive tests with USB audio devices connected to a musb host port
have shown reproducible pops and clicks in both the playback and the
capture stream.
These are related to how the early_tx hrtimer is set up, and it turns
out they can be fixed by reducing the timer's slack value from 40 to
25 us. Also, when the callback is ran without taking action, it should
be rescheduled 20 us later instead of 50 us.
Reported-and-tested-by: Sven Neumann <neumann@teufel.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It manages the powerdown signal,
and configures the internal glue logic and syscfg registers.
[ balbi@ti.com : actually switch over to of_platform_depopulate() ]
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.
This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those functions are only using within debugging
messages, grouping them into debug.h makes sense.
While at that, also add missing multiple inclusion
guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
After commit 2ec2a8be (usb: dwc3: gadget:
always enable IOC on bulk/interrupt transfers)
we created a situation where it was possible to
hang a bulk/interrupt endpoint if we had more
than one pending request in our queue and they
were both started with a single Start Transfer
command.
The problems triggers because we had not enabled
Transfer In Progress event for those endpoints
and we were not able to process early giveback
of requests completed without LST bit set.
Fix the problem by finally enabling Xfer In Progress
event for all endpoint types, except control.
Fixes: 2ec2a8be (usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DMrz
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.17-rc4
These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: Johan Hovold <johan@kernel.org>
Probe is testing if the current interface provides two bulk endpoints.
While this achieves the goal of only binding to the correct interface,
we already know we can find the device on interface number 1. Stop
checking the endpoints and just return successfully when interface
number 1 is probed.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
we don't to gate clocks until our children are
done with their remove path.
Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Cc: <stable@vger.kernel.org> # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
dep->endpoint.desc is checked at the beginning of
dwc3_gadget_ep_queue(), but after that it may be set to NULL
by another thread and then accessed again in dwc3_gadget_ep_queue().
This will lead to kernel oops.
Expand spinlock protection area to aviod race condition.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.
Fixes the following warning from the sparse checker:
drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)
Fixes: 81d5dfe6d8 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Up to now, when endpoint addresses in descriptors were non-consecutive,
there were created redundant files, which could cause problems in kernel,
when user tried to read/write to them. It was result of fact that maximum
endpoint address was taken as total number of endpoints in function.
This patch adds endpoint descriptors counting and storing their addresses
in eps_addrmap to verify their cohesion in each speed.
Endpoint address map would be also useful for further features, just like
vitual endpoint address mapping.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the usb_pkt_pop(). If a gadget driver calls
usb_ep_dequeue(), this driver will call the usb_pkt_pop().
So, the usb_pkt_pop() should cancel the transaction.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the condition of is_done in usbhsf_dma_push_done().
This function will be called after a transmission finished by DMAC.
So, the function should check if the transmission packet is short packet
or not. Also the function should call try_run to send the zero packet
by the pio handler if the "*is_done" is not set. Otherwize, the
transaction will not finish if a gadget driver sets the "zero" flag
in a transmission.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch protects the mod->irq_bempsts and mod->irq_brdysts by
spin lock in the usbhs_status_get_each_irq() because other functions
will write them during spin lock. Otherwise, the driver will clears
the BRDYSTS and/or BEMPSTS wrongly, and then, the transaction will not
finish.
Also since the driver should use the INTSTS0 and BRDYSTS and BEMPSTS
as the same timing, the patch protects them.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>] lr : [<c0278fb4>] psr: 60000193
sp : c0513ce8 ip : c0513c58 fp : c0513d24
r10: 00000001 r9 : 00000193 r8 : eebec4a0
r7 : eebec410 r6 : eebe0c6c r5 : 00000000 r4 : ee4a2774
r3 : 00000000 r2 : ee251e00 r1 : c0513cf4 r0 : ee4a2774
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Clearly this was meant to be an include guard, but a trailing
underscore was missing. It has been this way since the file was
introduced in 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver").
Fixes: 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.
The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.
Validated using the following usbtest write case in MUSB host mode.
# testusb -t1 -c1
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The UAC2 function driver currently responds to all packets at all times
with wMaxPacketSize packets. That results in way too fast audio
playback as the function driver (which is in fact supposed to define
the audio stream pace) delivers as fast as it can.
Fix this by sizing each packet correctly with the following steps:
a) Set the packet's size by dividing the nominal data rate by the
playback endpoint's interval.
b) If there is a residual value from the calculation in a), add
it to a accumulator to keep track of it across packets.
c) If the accumulator has gathered at least the number of bytes
that are needed for one sample frame, increase the packet size.
This way, the packet size calculation will get rid of any kind of
imprecision that would otherwise occur with a simple division over
time.
Some of the variables that are needed while processing each packet
are pre-computed for performance reasons.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With packet sizes other than 512, payloads in the packets may wrap
around the ALSA dma buffer partially, which leads to memory corruption
and audible clicks and pops in the audio stream at the moment, because
there is no boundary check before the memcpy().
In preparation to an implementation for smaller and dynamically sized
packets, we have to address such cases, and copy the payload in two
steps conditionally.
The 'src' and 'dst' approach doesn't work here anymore, as different
behavior is necessary in playback and capture cases. Thus, this patch
open-codes the routine now.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a simple container_of() wrapper to get a struct f_uac2_opts from a
struct struct audio_dev. Use it in two places where it is currently
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In afunc_bind() and afunc_set_alt(), &uac2->pdev.dev are used multiple
times. Adding a short-hand for them makes lines shorter so we can
remove some line wraps.
No functional change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Restructure some code to make it easier to read.
While at it, return -ENOMEM instead of -EINVAL if
usb_ep_alloc_request() fails, and omit the logging in such cases
(the mm core will complain loud enough).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Flatten the start_transfer function by reversing the if condition and
returning early out of the function if everything went fine. It makes
the function look less complicated, at least to me, and easier to
understand.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit f226708(usb: gadget: composite: dequeue cdev->req before free it in
composite_dev_cleanup) fixed a bug: free the usb request(i.e. cdev->req) but
does not dequeue it beforehand. This fix is not proper enough because it
dequeues the request after free its data buffer, considering the hardware can
access the buffer's memory anytime before the request's complettion rountine
runs, and usb_ep_dequeue always call the complettion rountine before it returns,
so the best way is to dequeue the request before free its buffer.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `usbhsg_dma_map_ctrl':
mod_gadget.c:(.text+0x53b226): undefined reference to `usb_gadget_map_request'
mod_gadget.c:(.text+0x53b242): undefined reference to `usb_gadget_unmap_request'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb[2,3] drivers got replaced by
drivers/phy/phy-samsung-usb[2,3] ones and the old common Samsung
USB PHY code is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb3 driver got replaced by
drivers/phy/phy-samsung-usb3 one and is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb2 driver got replaced by
drivers/phy/phy-samsung-usb2 one and is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add simple driver for Medtronic CareLink USB devices.
Reported-by: Benjamin West <bewest@gmail.com>
Tested-by: Benjamin West <bewest@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use direct method for supported baud rates, otherwise use divisors.
Limit baud rate to 12 Mbaud with HX type.
This change has been tested to work with PL-2303HX at 115200, 500000,
1000000, 2000000, 2500000, 3000000 and 4000000 baud rates.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.
Cc: <stable@vger.kernel.org>
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.
It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist. This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for NOVITUS Bono E thermal printer.
Reported-by: Emanuel Koczwara <poczta@emanuelkoczwara.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Using $(PWD) breaks builds when make was invoked from outside
of the kernel tree.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces the use of the functions usb_endpoint_type and
usb_endpoint_num.
The Coccinelle semantic patch that makes these changes is as follows:
@@ struct usb_endpoint_descriptor *epd; @@
- (epd->bEndpointAddress & \(USB_ENDPOINT_NUMBER_MASK\|0x0f\))
+ usb_endpoint_num(epd)
@@ struct usb_endpoint_descriptor *epd; @@
- (epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\))
+ usb_endpoint_type(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two simple test cases for interrupt endpoints are added to the usbtest.c file.
These are simple non-queued interrupt IN and interrupt OUT transfers. Currently,
only gadget zero is capable of executing the interrupt EP test cases. However,
extending the same to other gadgets is extremely simple and can be done
on-demand.
The two new tests added are
- Test 25: To verify Interrupt OUT transfer
- Test 26: To verify Interrupt IN transfer
Since the default value of wMaxPacketSize is set as 1024, so interrupt
IN transfers must be specified with the size parameter = multiple of
1024. Otherwise the default value (512) in the usbtest application fails
the transfer. See [RUN 4] for sample logs
The application logs (usbtest) and corresponding kernel logs are as
following:
[Run 1]
./testusb -a -c 10 -s 2048 -t 26 -v 511
usbtest 7-1:3.0: TEST 26: read 2048 bytes 10 times
[Run 2]
./testusb -a -c 10 -s 1024 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1024 bytes 10 times
[Run 3]
./testusb -a -c 10 -s 1098 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1098 bytes 10 times
[Run 4 - Failure case scenario]
./testusb -a -t 26
unknown speed /dev/bus/usb/007/004 0
/dev/bus/usb/007/004 test 26 --> 75 (Value too large for defined data type)
usbtest 7-1:3.0: TEST 26: read 512 bytes 1000 times
usb 7-1: test26 failed, iterations left 999, status -75 (not 0)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unfortunately, the USB gadget layer has this weird things where NULL
skbs are passed into ops->ndo_start_xmit() in order to trigger the
dev->wrap() calls to build packets.
This is completely outside of the allowable range of sane arguments
for the ndo_start_xmit method. All invocations of ndo_start_xmit()
should be with non-NULL SKB arguments.
Put back the direct call, but with a comment explaining how this
is not acceptable in the long term.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bdd405d2a5 ("usb: hub: Prevent hub autosuspend if
usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is
disabled. Fix that by doing a simple #ifdef guard around it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Michael Welling <mwelling@emacinc.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a bit bigger hammer then I would like to use for this, but for now
it will have to make do. I'm working on getting my hands on one of these so
that I can try to get streams to work (with a quirk flag if necessary) and
then we can re-enable them.
For now this at least makes uas capable disk enclosures work again by forcing
fallback to the usb-storage driver.
https://bugzilla.kernel.org/show_bug.cgi?id=79511
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the number of ports requested by subdriver to avoid
writing beyond the end of fixed-size array in interface data.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of ports requested by a
subdriver (which could have been determined from device descriptors) did
not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the maximum number of endpoints per type to avoid
writing beyond the end of a stack-allocated array.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of endpoints of a certain
type reported by a device did not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupt endpoints behave quite similar to the bulk endpoints with the
difference that the endpoints expect data sending/reception request at
particular intervals till the whole data has not been transmitted.
The interrupt EP support is added to gadget zero. A new alternate setting (=2)
has been added. It has 2 interrupt endpoints. The default parameters are set as:
bInterval: 1 ms for FS and 8 uFrames (implying 1 ms) for HS/SS
wMaxPacketSize: 64 bytes for FS and 1024 bytes for HS/SS
However, the same can be overridden through the module parameter interface.
The code is tested for HS and SS on a platform having DWC3 controller.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the ttyGS PREFIX macro from u_serial.c and replace all occurences with
the hardcoded ttyGS string.
This macro was mostly used in a few debug/warning messages and a lot of
hardcoded ttyGS existed beneath. It may have been used for renaming the
tty, but if done so most debug messages would have ignored this.
Due to the fact the usage of this PREFIX in all debug calls would have
resulted in a hard to read/grep code it is removed completely.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace the VDBG and DBG macro with the kernels "proper" debug macros
(dev_vdbg and dev_dbg) in f_acm.c, f_obex.c & f_serial.c
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes the phy reset clk and reset line optional as this clk
is not available on boards like IFC6410 with APQ8064.
phy-reset clk is only used as argument to the mach level callbacks, so
this patch adds condition before clk_get calls so that the driver
wouldn't fail on SOCs which do not have this support.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds support for the USB PHY in Vybrid VF610. We assume that
the disconnection without VBUS is also needed for Vybrid.
Tests showed, without MXS_PHY_NEED_IP_FIX, enumeration of devices
behind a USB Hub fails with errors:
[ 215.163507] usb usb1-port1: cannot reset (err = -32)
[ 215.170498] usb usb1-port1: cannot reset (err = -32)
[ 215.185120] usb usb1-port1: cannot reset (err = -32)
[ 215.191345] usb usb1-port1: cannot reset (err = -32)
[ 215.202487] usb usb1-port1: cannot reset (err = -32)
[ 215.207718] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[ 215.219317] usb usb1-port1: unable to enumerate USB device
Hence we also enable the MXS_PHY_NEED_IP_FIX flag.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we want to keep support for both older usb-phys as well as the
newer generic phys, lets first get the generic PHYs and fallback to
older USB-PHYs only when we fail to get the former.
This should fix the issue with ehci-exynos and ohci-exynos, wherein
in the absence of SAMSUNG_USB2PHY config symbol, we end up getting
the NOP_USB_XCEIV phy when the same is enabled. And thus the PHYs
are not configured properly.
Reported-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jingoo Han <jg1.han@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user specifies that USB autosuspend must be disabled by module
parameter "usbcore.autosuspend=-1" then we must prevent
autosuspend of USB hub devices as well.
commit 596d789a21 introduced in v3.8 changed the original behaivour
and stopped respecting the usbcore.autosuspend parameter for hubs.
Fixes: 596d789a21 "USB: set hub's default autosuspend delay as 0"
Cc: [3.8+] <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michael Welling <mwelling@emacinc.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have a j5 create (JUA210) USB 2 video device and adding it device id
to SIS USB video gets it to work.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the default EP max packet value as 8 bytes, because in the case
of low-speed, 'ep_mps' is not set. Thus, the default value of 'ep_mps'
should be considered for the case of low-speed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The roothub's index per controller is from 0, but the hub port index per hub
is from 1, this patch fixes "can't find device at roohub" problem for connecting
test fixture at roohub when do USB-IF Embedded Host High-Speed Electrical Test.
This patch is for v3.12+.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uSCSI from Newer Technology is a SCSI-USB converter with USB ID 06ca:2003.
Like several other SCSI-USB products, it's a Shuttle Technology OEM device.
Without a suitable entry in unusual-devs.h, the converter can only access the
(single) device with SCSI ID 0. Copying the entry for device 04e6:0002 allows
it to work with devices with other SCSI IDs too.
There are currently six entries for Shuttle-developed SCSI-USB devices in
unusual-devs.h (grep for euscsi):
04e6:0002 Shuttle eUSCSI Bridge USB_SC_DEVICE, USB_PR_DEVICE
04e6:000b Shuttle eUSCSI Bridge USB_SC_SCSI, USB_PR_BULK
04e6:000c Shuttle eUSCSI Bridge USB_SC_SCSI, USB_PR_BULK
050d:0115 Belkin USB SCSI Adaptor USB_SC_SCSI, USB_PR_BULK
07af:0004 Microtech USB-SCSI-DB25 USB_SC_DEVICE, USB_PR_DEVICE
07af:0005 Microtech USB-SCSI-HD50 USB_SC_DEVICE, USB_PR_DEVICE
lsusb -v output for the uSCSI lists
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
This patch adds an entry for the uSCSI to unusual_devs.h.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was used back when usbip-host was an interface device driver;
after the conversion to device driver, the table remained unused.
Remove it in order to stop receiving a warning about it.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this point, USB/IP kernel code is fully functional
and can be moved out of staging.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's our first set of fixes for v3.17-rc cycle. Most fixes are
pretty minor changes like the signedness bug in dwc3, or the wrong
string format on MUSB.
The most interesting part is the addition of Intel Quark X1000 support
to PCH UDC.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT9NZWAAoJEIaOsuA1yqREUoYP/jMbfKZGhOhFn45l4wWGheBA
JO6gi97zv0TzHEoMCi4MFPiwAJIFEH/868v2s8EchgcIZcRfINlc2gO4/CHnRhXi
k80WU+9w9rvkA9WDzSSa2dAhyMe6mkunCl3MVNPaj0ZxcHx6Woi+UxWEv3xlHKDN
sksZ7qdjs0yYNHtn7qExNSrgP6hvAPRpZPrsTp6k5wuSvvD0voM7mRtcHHg9JRi7
FDs6gGNe5v8DuO4v3fticj2XBW6RH8kehTa1IRn7s+kCQK3uFGN8MbrdmYfaX/Y9
8KTswXdR+ywA1RHrO7zqdxii9jIo2wePdiemkSozgEofuwHuLcoK3ggaYuy+4iwo
sOBh2bYSrie1aC8pTOA17qeWmShBxeTceDgBisMSjlBthlULq0DyvVr8KTVHcMe9
JaDaWp5eq/v1gsld5KugGdyTaG9JIGcnnOcsYEAaTJBK2rXcUqUkqoh2X9IH980l
mpfLVhfTtiJRqSSyKnv6rxhxZx4IY+swgkIac1J0xpISDp/SbqXsE0iJw3NeWk/m
ufXZpWqO4fwRUSLQvcuesJN4DcddnOC1R3XDsoTjHHiBmrIwDbPK67GsJXKDCGLM
YqgMKugevjlo1/pC4pSIh4nRsgDb2SvtNGLHOB3l/NeqNVtvX3Ai4eLoh8n691Bt
E5J32F4xI1q3h7ADJQvg
=Rb6u
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into work-linus
Felipe writes:
usb: fixes for v3.17-rc2
Here's our first set of fixes for v3.17-rc cycle. Most fixes are
pretty minor changes like the signedness bug in dwc3, or the wrong
string format on MUSB.
The most interesting part is the addition of Intel Quark X1000 support
to PCH UDC.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch fixes a potential security issue in the whiteheat USB driver
which might allow a local attacker to cause kernel memory corrpution. This
is due to an unchecked memcpy into a fixed size buffer (of 64 bytes). On
EHCI and XHCI busses it's possible to craft responses greater than 64
bytes leading a buffer overflow.
Signed-off-by: James Forshaw <forshaw@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates fix the log level for some option log messages that started
bothering people after a recent change.
They also fix some issues reported against the zte_ev driver by moving most
device ids back from the zte_ev driver to the option driver (and removing two
duplicate ids). The zte_ev driver is planned to be removed in 3.18.
Some new device ids are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+RG
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into work-linus
Johan writes:
USB-serial fixes for v3.17-rc2
These updates fix the log level for some option log messages that started
bothering people after a recent change.
They also fix some issues reported against the zte_ev driver by moving most
device ids back from the zte_ev driver to the option driver (and removing two
duplicate ids). The zte_ev driver is planned to be removed in 3.18.
Some new device ids are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
As the driver is in mainline we can remove the version numbers.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If uvc->control_buf is successfuly allocated but uvc->control_req
is not, uvc->control_buf is not freed in the error recovery path.
With this patch applied uvc->control_buf is freed unconditionally;
if it happens to be NULL kfree on it is safe anyway.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Activate the videobuf2 DMABUF support. As vb2-vmalloc supports the
importer role only, exporting buffers isn't supported yet. When the
exporter role will be implemented in vb2-vmalloc the UVC gadget driver
will automatically gain support for it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The disconnect of the USB Device is a common pattern for
an UVC Camera. In many cases this will give us an meaningless
information for all buffers that couldn't be enqueued.
That patch changes this to KERN_DEBUG.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using f_uac1 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When configfs support is added the values in question will have to be
used in two different places. Substitute them with defined constants
to avoid duplicating magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_gstring_attach interface.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting uac1 to the new function interface requires converting
the USB uac1's function code and its users.
This patch converts the f_uac1.c to the new function interface.
The file is now compiled into a separate usb_f_uac1.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Integrating configfs requires converting f_uac1 to new function interface,
which in turn requires converting it to the new function interface,
which involves separate compilation of f_uac1.c into usb_f_uac1.ko.
u_uac1.c contains some module parameters. After this patch is applied
they are still a part of the resulting g_audio.ko, but can be guarded
with a compatiblity flag which will be removed when no users of the old
function interface of f_uac1 are left.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
uac1 function is missing strings. Add them.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using f_uac2 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When configfs is integrated the same values will have to be used
as defaults. Use symbolic names in order not to duplicate magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_gstring_attach interface.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting uac2 to the new function interface requires converting
the USB uac2's function code and its users.
This patch converts the f_uac2.c to the new function interface.
The file is now compiled into a separate usb_f_uac2.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Eliminate static struct *agdev_g from f_uac2.c.
It is used for freeing its memory, but the same address can be found
by calling container_of in afunc_unbind(). This implies eliminating
uac2_unbind_config(). The audio_config_driver in audio.c does not have
its unbind method any more. It has been used only when uac2 is used,
so uac2 itself can handle unbinding in afunc_unbind().
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unnecessary lines of register bit definitions in order
to enhance the readability. In this case, there are lines
per register offset definitions. There is no functional change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The variable $(PWD) is useless, and it may break the compilation.
For example, it breaks the kernel compilation when it's done with
buildroot :
/home/trem/Codes/armadeus/armadeus/buildroot/output/host/usr/bin/ccache
/home/trem/Codes/armadeus/armadeus/buildroot/output/host/usr/bin/arm-buildroot-linux-uclibcgnueabi-gcc
-Wp,-MD,drivers/usb/gadget/legacy/.hid.o.d -nostdinc -isystem
/home/trem/Codes/armadeus/armadeus/buildroot/output/host/usr/lib/gcc/arm-buildroot-linux-uclibcgnueabi/4.7.3/include
-I./arch/arm/include -Iarch/arm/include/generated -Iinclude
-I./arch/arm/include/uapi -Iarch/arm/include/generated/uapi
-I./include/uapi -Iinclude/generated/uapi -include
./include/linux/kconfig.h -D__KERNEL__ -mlittle-endian -Wall -Wundef
-Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common
-Werror-implicit-function-declaration -Wno-format-security
-fno-dwarf2-cfi-asm -mabi=aapcs-linux -mno-thumb-interwork -mfpu=vfp
-funwind-tables -marm -D__LINUX_ARM_ARCH__=5 -march=armv5te
-mtune=arm9tdmi -msoft-float -Uarm -fno-delete-null-pointer-checks -O2
--param=allow-store-data-races=0 -Wframe-larger-than=1024
-fno-stack-protector -Wno-unused-but-set-variable -fomit-frame-pointer
-fno-var-tracking-assignments -g -Wdeclaration-after-statement
-Wno-pointer-sign -fno-strict-overflow -fconserve-stack
-Werror=implicit-int -Werror=strict-prototypes -DCC_HAVE_ASM_GOTO
-I/home/trem/Codes/armadeus/armadeus/buildroot/drivers/usb/gadget/
-I/home/trem/Codes/armadeus/armadeus/buildroot/drivers/usb/gadget/udc/
-I/home/trem/Codes/armadeus/armadeus/buildroot/drivers/usb/gadget/function/
-DMODULE -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(hid)"
-D"KBUILD_MODNAME=KBUILD_STR(g_hid)" -c -o
drivers/usb/gadget/legacy/hid.o drivers/usb/gadget/legacy/hid.c
drivers/usb/gadget/epautoconf.c:23:26: erreur fatale: gadget_chips.h :
Aucun fichier ou dossier de ce type
This compilation line include :
..../buildroot/driver/usb/gadget
but the real path is :
..../buildroot/output/build/linux-3.17-rc1/driver/usb/gadget
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is to enable the USB gadget device for Intel Quark X1000
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@intel.com>
Signed-off-by: Bing Niu <bing.niu@intel.com>
Signed-off-by: Alvin (Weike) Chen <alvin.chen@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the pending buffers in the queue could not be pushed to the udc
endpoint we have to cancel the uvc_queue. Otherwise the gadget will get
stuck on this error. This patch calls uvc_queue_cancel if usb_ep_queue
failed.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
linux-2.6/drivers/usb/wusbcore/wa-xfer.c: In function 'wa_buf_in_cb':
linux-2.6/drivers/usb/wusbcore/wa-xfer.c:2590: warning: 'rpipe' may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Suggested-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-2.6/drivers/usb/core/hub.c: In function 'usb_disconnect':
linux-2.6/drivers/usb/core/hub.c:2110: warning: 'hub' may be used uninitialized in this function
linux-2.6/drivers/usb/core/hub.c:2111: warning: 'port1' may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-2.6/drivers/usb/dwc2/gadget.c: In function 's3c_hsotg_irq_enumdone':
linux-2.6/drivers/usb/dwc2/gadget.c:1904: warning: 'ep_mps' may be used uninitialized in this function
Acked-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we manually need to move the TR dequeue pointer we need to set the
correct cycle bit as well. Previously we used the trb pointer from the
last event received as a base, but this was changed in
commit 1f81b6d22a ("usb: xhci: Prefer endpoint context dequeue pointer")
to use the dequeue pointer from the endpoint context instead
It turns out some Asmedia controllers advance the dequeue pointer
stored in the endpoint context past the event triggering TRB, and
this messed up the way the cycle bit was calculated.
Instead of adding a quirk or complicating the already hard to follow cycle bit
code, the whole cycle bit calculation is now simplified and adapted to handle
event and endpoint context dequeue pointer differences.
Fixes: 1f81b6d22a ("usb: xhci: Prefer endpoint context dequeue pointer")
Reported-by: Maciej Puzio <mx34567@gmail.com>
Reported-by: Evan Langlois <uudruid74@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Maciej Puzio <mx34567@gmail.com>
Tested-by: Evan Langlois <uudruid74@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD xHC also needs short tx quirk after tested on most of chipset
generations. That's because there is the same incorrect behavior like
Fresco Logic host. Please see below message with on USB webcam
attached on xHC host:
[ 139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
Reported-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Shriraj-Rai P <shriraj-rai.p@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a Renesas uPD720231 chipset usb-3 uas to sata bridge with a 120G
Crucial M500 ssd, model string: Crucial_ CT120M500SSD1, together with a
the integrated Intel xhci controller on a Haswell laptop:
00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)
The following error gets logged to dmesg:
xhci error: Transfer event TRB DMA ptr not part of current TD
Treating COMP_STOP the same as COMP_STOP_INVAL when no event_seg gets found
fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit [5ee0f803cc3a: usbcore: don't log on consecutive debounce
failures of the same port] added the check of the reliable port, but
it also replaced the device argument to dev_err() wrongly, which leads
to a NULL dereference.
This patch restores the right device, port_dev->dev. Also, since
dev_err() itself shows the port number, reduce the port number shown
in the error message, essentially reverting to the state before the
commit 5ee0f803cc.
[The fix suggested by Hannes, and the error message cleanup suggested
by Alan Stern]
Fixes: 5ee0f803cc ('usbcore: don't log on consecutive debounce failures of the same port')
Reported-by: Hannes Reinecke <hare@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of error, the function memdup_user() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ret" should be signed. It's only used for zero and negative error
codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As, the interrupt for DMA is counted from 1, so need to checked
the USBA_NR_DMAS, in old way, it only check (USBA_NR_DMAS - 1),
so fix it.
Reported-by: Max Liao <liaops@embest-tech.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, PHYPARAM1_PCS_TXDEEMPH is set as
6 bits [5:0]. Thus, the bit mask should be set as 0x3f, instead
of 0x1f.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After dbgp_bind()-dbgp_unbind() cycle happens, static variable dbgp
contains pointers to already deallocated memory (dbgp.serial and dbgp.req).
If the next dbgp_bind() fails, for example in usb_ep_alloc_request(),
dbgp_bind() calls dbgp_unbind() on failure path,
and dbgp_unbind() frees dbgp.serial that still stores a pointer
to already deallocated memory.
The patch sets pointers to NULL in dbgp_unbind().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using kfree to free data allocated with devm_kzalloc causes double frees.
The Coccinelle semantic patch that fixes this problem is as follows:
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When __usb_find_phy_dev() does not return error and
try_module_get() fails, return -ENODEV.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added support to the ftdi_sio driver for ekey Converter USB which
uses an FT232BM chip.
Signed-off-by: Jaša Bartelj <jasa.bartelj@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds a new device id to the pl2303 driver for the ZTEK device.
Reported-by: Mike Chu <Mike-Chu@prolific.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for Basic Micro ATOM Nano USB2Serial adapters.
Reported-by: Nicolas Alt <n.alt@mytum.de>
Tested-by: Nicolas Alt <n.alt@mytum.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dublicate Qualcom PID 0x3197 which is already handled by the
moto-modem driver since commit 6986a978ee ("USB: add new moto_modem
driver for some Morotola phones").
Fixes: 799ee9243d ("USB: serial: add zte_ev.c driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dublicate Gobi PID 0x9008 which is already handled by the
qcserial driver since commit f05932c0ca ("USB: qcserial: Add extra
device IDs").
Fixes: 799ee9243d ("USB: serial: add zte_ev.c driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 73228a0538 ("USB: option,zte_ev: move most ZTE
CDMA devices to zte_ev").
Move the IDs of the devices that were previously driven by the option
driver back to that driver.
As several users have reported, the zte_ev driver is causing random
disconnects as well as reconnect failures.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Liu Lei, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Note that the zte_ev driver is based on code (once) distributed by ZTE
that still appears to originally have been reverse-engineered and bolted
onto the generic driver.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1), this is a first step in ultimately removing the redundant
zte_ev driver.
Note that AC2726 had already been moved back to option, and that some
IDs were in the device table of both drivers prior to the commit being
reverted.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This VIA Telecom baseband processor is used is used by by u-blox in both the
FW2770 and FW2760 products and may be used in others as well.
This patch has been tested on both of these modem versions.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not log normal interrupt-urb shutdowns as errors.
The option driver has always been logging any nonzero interrupt-urb
status as an error, including when the urb is killed during normal
operation.
Commit 9096f1fbba ("USB: usb_wwan: fix potential NULL-deref at
resume") moved the interrupt urb submission from port probe and release
to open and close, thus potentially increasing the number of these
false-positive error messages dramatically.
Reported-by: Ed Butler <ressy66@ausics.net>
Tested-by: Ed Butler <ressy66@ausics.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2ZIACgkQMUfUDdst+ylvQwCfQKPKcwhtq4vJ2imUzJROEZwN
ygYAnRpFpH/19X59uGSdE7DAdhbitqKg
=uPh1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no one
was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1wYACgkQMUfUDdst+ykrNwCgswPkRSAPQ3C8WvLhzUYRZZ/L
AqEAoJP0Q8Fz8unXjlSMcx7pgcqUaJ8G
=mrTQ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no
one was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while"
* tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (2199 commits)
staging: comedi: addi_apci_1564: remove diagnostic interrupt support code
staging: comedi: addi_apci_1564: add subdevice to check diagnostic status
staging: wlan-ng: coding style problem fix
staging: wlan-ng: fixing coding style problems
staging: comedi: ii_pci20kc: request and ioremap memory
staging: lustre: bitwise vs logical typo
staging: dgnc: Remove unneeded dgnc_trace.c and dgnc_trace.h
staging: dgnc: rephrase comment
staging: comedi: ni_tio: remove some dead code
staging: rtl8723au: Fix static symbol sparse warning
staging: rtl8723au: usb_dvobj_init(): Remove unused variable 'pdev_desc'
staging: rtl8723au: Do not duplicate kernel provided USB macros
staging: rtl8723au: Remove never set struct pwrctrl_priv.bHWPowerdown
staging: rtl8723au: Remove two never set variables
staging: rtl8723au: RSSI_test is never set
staging:r8190: coding style: Fixed checkpatch reported Error
staging:r8180: coding style: Fixed too long lines
staging:r8180: coding style: Fixed commenting style
staging: lustre: ptlrpc: lproc_ptlrpc.c - fix dereferenceing user space buffer
staging: lustre: ldlm: ldlm_resource.c - fix dereferenceing user space buffer
...
usbfs allows user space to pass down an URB which sets URB_SHORT_NOT_OK
for output URBs. That causes usbcore to log messages without limit
for a nonsensical disallowed combination. The fix is to silently drop
the attribute in usbfs.
The problem is reported to exist since 3.14
https://www.virtualbox.org/ticket/13085
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So that an user who wants to use uas can see why he is not getting uas.
Also move the check down so that we don't warn if there are other reasons
why uas cannot work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain about controllers without sg support if there are other
reasons why uas cannot be used anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 7023 product id is the generic product id for the Etron EJ168, it is
not specific to the version found on the Asrock P67 motherboard. The same id
is e.g. also used on Gigabyte motherboards and on no-name pci-e usb-3 addon
cards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.
The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.
This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.
But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.
The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.
Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.
https://bugzilla.redhat.com/show_bug.cgi?id=1121288https://bugzilla.kernel.org/show_bug.cgi?id=80101
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some jmicron uas chipsets act up (they disconnect from the bus) when sending
more then 32 commands to them at once.
Rather then building an ever growing list with usb-id based quirks for
devices using this chipset, simply reduce the qdepth to 32 when connected
over usb-2. 32 should be plenty to keep things close to maximum
possible throughput on usb-2.
Cc: stable@vger.kernel.org
Tested-and-reported-by: Laszlo T. <tlacix@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a usb quirk to support devices with interupt endpoints
and bInterval values expressed as microframes. The quirk causes the
parse endpoint function to modify the reported bInterval to a standards
conforming value.
There is currently code in the endpoint parser that checks for
bIntervals that are outside of the valid range (1-16 for USB 2+ high
speed and super speed interupt endpoints). In this case, the code assumes
the bInterval is being reported in 1ms frames. As well, the correction
is only applied if the original bInterval value is out of the 1-16 range.
With this quirk applied to the device, the bInterval will be
accurately adjusted from microframes to an exponent.
Signed-off-by: James P Michels III <james.p.michels@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for new Xsens devices, using Xsens' own Vendor ID.
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The converters are used in specific products. It can be useful to know
which they are exactly.
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver hasn't been fully cleaned up and it doesn't look like anyone
is working on it anymore (including the original author). So remove the
driver and all references to it. If someone wants to finish cleaning
the driver up and moving it out of staging, this commit can be reverted.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Cc: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warnings:
drivers/usb/chipidea/debug.c:211:5: warning:
symbol 'ci_otg_show' was not declared. Should it be static?
drivers/usb/chipidea/debug.c:334:5: warning:
symbol 'ci_registers_show' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-ENODEV is interpreted by the generic driver probing function as a
non-matching driver. This leads to a missing probe failure message.
Also a missing USB PHY is more of an invalid configuration of the usb
driver because it is necessary.
This patch returns -EINVAL if devm_usb_get_phy_by_phandle() returned -ENODEV.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Section 4.4.7.2 "Interrupt Transfer Bandwidth Requirements" of the USB3.0 spec
says:
A zero-length data payload is a valid transfer and may be useful for
some implementations.
So, extend the logic of allowing URB_ZERO_PACKET to interrupt urbs too.
Otherwise, the kernel throws warning of BOGUS transfer flags.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch adds an extra check to ohci-hcd's I/O watchdog routine. If
the controller stops updating the frame counter, we will assume it is
dead. But there has to be an exception: Some controllers stop the
frame counter when no ports are connected. Check to make sure there
is at least one active port before deciding the controller is dead.
(This test may appear racy, but it isn't. Enabling a newly connected
port takes several milliseconds, during which time the frame counter
must advance.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dennis New <dennisn@dennisn.linuxd.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some OHCI controllers have a bug: They fail to add completed TDs to
the done queue. Examining this queue is the only method ohci-hcd has
for telling when a transfer is complete; failure to add a TD can
result in an URB that never completes and cannot be unlinked.
This patch adds a watchdog routine to ohci-hcd. The routine
periodically scans the active ED and TD lists, looking for TDs which
are finished but not on the done queue. When one is found, and it is
certain that the controller hardware will never add the TD to the done
queue, the watchdog routine manually puts the TD on the done list so
that it can be handled normally.
The watchdog routine also checks for a condition indicating the
controller has died. If the done queue is non-empty but the
HccaDoneHead pointer hasn't been updated for a few hundred
milliseconds, we assume the controller will never update it and
therefore is dead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
URBs for a particular endpoint should complete sequentially. That is,
we shouldn't call the completion handler for one URB until the handler
for the previous URB has returned.
When the OHCI watchdog routine is added, there will be two paths for
completing URBs: interrupt handler and watchdog routine. Their
activities have to be synchronized so that completions don't occur in
multiple threads concurrently.
For that purpose, this patch creates an ohci_work() routine which will
be responsible for calling process_done_list() and finish_unlinks(),
the two routines that detect when an URB is complete. Everything will
funnel through ohci_work(), and it will be careful not to run in more
than one thread at a time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the way ohci-hcd handles the TD done list. In
addition to relying on the TD pointers stored by the controller
hardware, we need to handle TDs that the hardware has forgotten about.
This means the list has to exist even while the dl_done_list() routine
isn't running. That function essentially gets split in two:
update_done_list() reads the TD pointers stored by the hardware and
adds the TDs to the done list, and process_done_list() scans through
the list to handle URB completions. When we detect a TD that the
hardware forgot about, we will be able to add it to the done list
manually and then process it normally.
Since the list is really a queue, and because there can be a lot of
TDs, keep the existing singly linked implementation. To insure that
URBs are given back in order of submission, whenever a TD is added to
the done list, all the preceding TDs for the same endpoint must be
added as well (going back to the first one that isn't already on the
done list).
The done list manipulations must all be protected by the private
lock. The scope of the lock is expanded in preparation for the
watchdog routine to be added in a later patch.
We have to be more careful about giving back unlinked URBs. Since TDs
may be added to the done list by the watchdog routine and not in
response to a controller interrupt, we have to check explicitly to
make sure all the URB's TDs that were added to the done list have been
processed before giving back the URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an URB is unlinked from a dead controller, ohci-hcd gives back
the URB with no regard for cleaning up the internal data structures.
This won't play nicely with the upcoming changes to the TD done
list.
Therefore make ohci_urb_dequeue() call finish_unlinks(), which uses
td_done() to do a proper cleanup, rather than calling finish_urb()
directly. Also, remove the checks that urb_priv is non-NULL; the
driver guarantees that urb_priv will never be NULL for a valid URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts the important parts of commit 89a0fd18a9 (USB:
OHCI handles more ZFMicro quirks), namely, the parts related to
handling orphan TDs for interrupt endpoints. A later patch in this
series will introduce a more general mechanism that applies to all
endpoint types and all controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others. Such
devices fail to reconnect with same old address which was associated
with it before suspend.
When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.
Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port. In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.
Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.
I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.
So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.
XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present. USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.
This patch implements above delay, but only for SS device and when
persist is enabled.
So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.
Results:
Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I am removing two fix mes in this file as after dicussing then it seems
there is no reason to check against Null for usb_device as it can never
be NULL and this is check is therefore not needed.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some laptops have an internal port for a BT device which picks
up noise when the kill switch is used, but not enough to trigger
printk_rlimit(). So we shouldn't log consecutive faults of this kind.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cd (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This `usb_reset_device` command has been around since the driver was
originally reverse engineered. It doesn't cause much issue on single
interface CP210x devices, but on the CP2105 and CP2108 with 2 and 4
interfaces respectively it will cause instability on enumeration and
delays enumeration noticably. There should be no reason to reset a device
at startup, per the CP210x AN571 spec.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.
USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).
Some modifications are needed for an embedded Linux USB host to pass all
these tests. Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit. Then,
There are many Link Layer Tests which need host to generate specific
traffic.
This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.
lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.
echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind
Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.
echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id
Now connect LVS device with root hub port.
Test case specific traffic can be generated as follows whenever needed:
1. To issue "Get Device descriptor" command for TD.7.06:
echo > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc
2. To set U1 timeout to 127 for TD.7.18
echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout
3. To set U2 timeout to 0 for TD.7.18
echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout
4. To issue "Hot Reset" for TD.7.29
echo > /sys/bus/usb/devices/2-0\:1.0/hot_reset
5. To issue "U3 Entry" for TD.7.35
echo > /sys/bus/usb/devices/2-0\:1.0/u3_entry
6. To issue "U3 Exit" for TD.7.36
echo > /sys/bus/usb/devices/2-0\:1.0/u3_exit
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_alloc_dev is used by lvstest driver now which can be built as
module. Therefore export usb_alloc_dev symbol.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug in ohci-hcd. When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule. Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed. If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.
This fails when a controller dies. A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it. The remaining URBs cannot be unlinked,
which causes the USB stack to hang.
The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running. This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size. Also, the debug routine ohci_dump() has an unused argument.
This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently nobody ever remembered to add Scatter-Gather support to
ohci-hcd. This patch adds it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a host controller dies, we don't need to wait for a driver to
time out. We can shut down its URBs immediately. Without this
change, we can end up waiting 30 seconds for a mass-storage transfer
to time out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 2 methods for ZLP (zero-length packet) generation:
1) In software
2) Automatic generation by device controller
1) is implemented in UDC driver and it attaches ZLP to IN packet if
descriptor->size < wLength
2) can be enabled/disabled by setting ZLT bit in the QH
When gadget ffs is connected to ubuntu host, the host sends
get descriptor request and wLength in setup packet is 255 while the
size of descriptor which will be sent by gadget in IN packet is
64 byte. So the composite driver sets req->zero = 1.
In UDC driver following code will be executed then
if (hwreq->req.zero && hwreq->req.length
&& (hwreq->req.length % hwep->ep.maxpacket == 0))
add_td_to_list(hwep, hwreq, 0);
Case-A:
So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet.
ubuntu host will request 255 byte in IN request, gadget will send 64 byte
with ZLP and host will come to know that there is no more data.
But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to
automatically generate the ZLP which blocks enumeration for ~6 seconds due
to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING)
Case-B:
In case when gadget ffs is connected to Apple device, Apple device sends
setup packet with wLength=64. So descriptor->size = 64 and wLength=64
therefore req->zero = 0 and UDC driver will not attach any ZLP to the
IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't
further request for IN data. But ZLT=0 by default for endpoint 0 so
hardware tries to automatically generate the ZLP which blocks enumeration
for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any
requests (OUT/PING)
According to USB2.0 specs:
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase in which the
host requests more data than is contained in the specified data
structure. When all of the data structure is returned to the host,
the function should indicate that the Data stage is ended by
returning a packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of wMaxPacketSize
for the pipe, the function will return a zero-length packet to indicate
the end of the Data stage.
In Case-A mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software
ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then
enumeration doesn't block for 6 seconds.
In Case-B mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint then enumeration
still blocks due to ZLP automatically generated by hardware and host not needing
it. But if we keep software ZLP generation enabled but we set ZLT=1 for
endpoint 0 then enumeration doesn't block for 6 seconds.
So the proper solution for this issue seems to disable automatic ZLP generation
by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver)
handle the ZLP generation based on req->zero field.
Cc: stable@vger.kernel.org
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Johan Hovold