Commit Graph

2909 Commits

Author SHA1 Message Date
Robert Jarzmik 32a50b3a45 mtd: docg3: fix reading oob+data without correction
Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.

The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:07:17 +00:00
Robert Jarzmik 34db8a5a72 mtd: docg3: fix BCH registers
BCH registers are contiguous, not on every byte. Fix the
register definitions.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:07:16 +00:00
Robert Jarzmik dbc26d98f8 mtd: docg3: fix protection areas reading
The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:07:15 +00:00
Robert Jarzmik 84a930581e mtd: docg3: fix tracing of IO in writeb
Writeb was incorrectly traced as a 16 bits write, instead of
a 8 bits write. Fix it by tracing the correct width.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:07:13 +00:00
Robert Jarzmik ac48e800c0 mtd: docg3: fix debug log verbosity
Change the NOP debug log verbosity to very verbose to
unburden log analysis.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:07:12 +00:00
Shubhrajyoti D 12f049bd59 mtd: nand: Making MTD_NAND_OMAP2 depend on ARCH_OMAP2PLUS
Making  MTD_NAND_OMAP2 depend on ARCH_OMAP2PLUS instead of
oring with ARCH2/3/4.

Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:07:04 +00:00
Aaron Sierra 8e987465a1 mtd: cfi: Allow per-mapping CFI device endianness
This patch allows each CFI device map to use its own endianness. The
globally defined CFI endianness (CONFIG_MTD_CFI_NOSWAP,
CONFIG_MTD_CFI_BE_BYTE_SWAP or CONFIG_MTD_CFI_LE_BYTE_SWAP) becomes the
default value which can be overridden by a driver for a particular device.

Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:06:13 +00:00
Brian Norris 342ff28f5a mtd: mtd_blkdevs: don't increase 'open' count on error path
Some error paths in mtd_blkdevs were fixed in the following commit:

    commit 94735ec404
    mtd: mtd_blkdevs: fix error path in blktrans_open

But on these error paths, the block device's `dev->open' count is
already incremented before we check for errors. This meant that, while
the error path was handled correctly on the first time through
blktrans_open(), the device is erroneously considered already open on
the second time through.

This problem can be seen, for instance, when a UBI volume is
simultaneously mounted as a UBIFS partition and read through its
corresponding gluebi mtdblockX device. This results in blktrans_open()
passing its error checks (with `dev->open > 0') without actually having
a handle on the device. Here's a summarized log of the actions and
results with nandsim:

    # modprobe nandsim
    # modprobe mtdblock
    # modprobe gluebi
    # modprobe ubifs
    # ubiattach /dev/ubi_ctrl -m 0
    ...
    # ubimkvol /dev/ubi0 -N test -s 16MiB
    ...
    # mount -t ubifs ubi0:test /mnt
    # ls /dev/mtdblock*
    /dev/mtdblock0  /dev/mtdblock1
    # cat /dev/mtdblock1 > /dev/null
    cat: can't open '/dev/mtdblock4': Device or resource busy
    # cat /dev/mtdblock1 > /dev/null

    CPU 0 Unable to handle kernel paging request at virtual address
    fffffff0, epc == 8031536c, ra == 8031f280
    Oops[#1]:
    ...
    Call Trace:
    [<8031536c>] ubi_leb_read+0x14/0x164
    [<8031f280>] gluebi_read+0xf0/0x148
    [<802edba8>] mtdblock_readsect+0x64/0x198
    [<802ecfe4>] mtd_blktrans_thread+0x330/0x3f4
    [<8005be98>] kthread+0x88/0x90
    [<8000bc04>] kernel_thread_helper+0x10/0x18

Cc: stable@kernel.org [3.0+]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:04:01 +00:00
Brian Norris 8c34233596 mtd: nand: scan 1st and 2nd page for Macronix SLC
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 17:59:53 +00:00
Brian Norris c01804edde mtd: nand: add 512 Mbit device code (Macronix)
Macronix MX30LF1208AA is a 512 Mbit NAND with device code 0xF0.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 17:59:44 +00:00
Brian Norris c1257b4798 mtd: nand: add Macronix manufacturer
Macronix is produing SLC NAND MX30LF1208AA, so add their manufacturer
code to the manufacturer lists.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 17:59:33 +00:00
Ilya Yanok c32987918e mtd: plat_ram: call mtd_device_register only if partition data exists
mtd_device_parse_register() registers the device as a whole if no
partition data is passed so there is no reason to call
mtd_device_register() after that.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-12-19 11:13:52 +00:00
Jonathan Cameron 7148b79992 mtd: pxa2xx-flash.c: It used to fall back to provided table.
Make this work again.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-12-07 10:05:15 +00:00
Wolfram Sang df16c86a56 mtd: gpmi: add missing include 'module.h'
Fixes:

drivers/mtd/nand/gpmi-nand/gpmi-nand.c: In function 'gpmi_nfc_init':
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: At top level:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:15: error: expected declaration specifiers or '...' before string constant
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: data definition has no type or storage class
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'

and some more...

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-12-05 11:37:54 +00:00
Tony Breeds 629be5f275 mtd: ndfc: fix typo in structure dereference
In commit 9d7948c500 (mtd: ndfc: use
ofpart through generic parsing) we dereference a non pointer type
causing the following compiler error:
drivers/mtd/nand/ndfc.c: In function 'ndfc_chip_init':
drivers/mtd/nand/ndfc.c:191: error: invalid type argument of '->' (have 'struct mtd_part_parser_data')

Fix that.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-12-02 16:27:03 +00:00
Jonas Gorski 4e549d6d4a MTD: MAPS: bcm963xx-flash.c: explicitly include module.h
module.h was previously implicitly included through mtd/mtd.h.

Fixes the following build failure after the module.h cleanup:

  CC      drivers/mtd/maps/bcm963xx-flash.o
drivers/mtd/maps/bcm963xx-flash.c: In function 'bcm963xx_probe':
drivers/mtd/maps/bcm963xx-flash.c:208:29: error: 'THIS_MODULE' undeclared (first use in this function)
 [...]
drivers/mtd/maps/bcm963xx-flash.c:276:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/mtd/maps/bcm963xx-flash.c:276:15: warning: function declaration isn't a prototype
make[7]: *** [drivers/mtd/maps/bcm963xx-flash.o] Error 1

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-11-07 21:26:55 -05:00
Linus Torvalds e0d65113a7 Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (226 commits)
  mtd: tests: annotate as DANGEROUS in Kconfig
  mtd: tests: don't use mtd0 as a default
  mtd: clean up usage of MTD_DOCPROBE_ADDRESS
  jffs2: add compr=lzo and compr=zlib options
  jffs2: implement mount option parsing and compression overriding
  mtd: nand: initialize ops.mode
  mtd: provide an alias for the redboot module name
  mtd: m25p80: don't probe device which has status of 'disabled'
  mtd: nand_h1900 never worked
  mtd: Add DiskOnChip G3 support
  mtd: m25p80: add EON flash EN25Q32B into spi flash id table
  mtd: mark block device queue as non-rotational
  mtd: r852: make r852_pm_ops static
  mtd: m25p80: add support for at25df321a spi data flash
  mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
  mtd: nand: switch `check_pattern()' to standard `memcmp()'
  mtd: nand: invalidate cache on unaligned reads
  mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
  mtd: nand: wait to set BBT version
  mtd: nand: scrub BBT on ECC errors
  ...

Fix up trivial conflicts:
 - arch/arm/mach-at91/board-usb-a9260.c
	Merged into board-usb-a926x.c
 - drivers/mtd/maps/lantiq-flash.c
	add_mtd_partitions -> mtd_device_register vs changed to use
	mtd_device_parse_register.
2011-11-07 09:11:16 -08:00
Linus Torvalds 32aaeffbd4 Merge branch 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
  Revert "tracing: Include module.h in define_trace.h"
  irq: don't put module.h into irq.h for tracking irqgen modules.
  bluetooth: macroize two small inlines to avoid module.h
  ip_vs.h: fix implicit use of module_get/module_put from module.h
  nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
  include: replace linux/module.h with "struct module" wherever possible
  include: convert various register fcns to macros to avoid include chaining
  crypto.h: remove unused crypto_tfm_alg_modname() inline
  uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
  pm_runtime.h: explicitly requires notifier.h
  linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
  miscdevice.h: fix up implicit use of lists and types
  stop_machine.h: fix implicit use of smp.h for smp_processor_id
  of: fix implicit use of errno.h in include/linux/of.h
  of_platform.h: delete needless include <linux/module.h>
  acpi: remove module.h include from platform/aclinux.h
  miscdevice.h: delete unnecessary inclusion of module.h
  device_cgroup.h: delete needless include <linux/module.h>
  net: sch_generic remove redundant use of <linux/module.h>
  net: inet_timewait_sock doesnt need <linux/module.h>
  ...

Fix up trivial conflicts (other header files, and  removal of the ab3550 mfd driver) in
 - drivers/media/dvb/frontends/dibx000_common.c
 - drivers/media/video/{mt9m111.c,ov6650.c}
 - drivers/mfd/ab3550-core.c
 - include/linux/dmaengine.h
2011-11-06 19:44:47 -08:00
Linus Torvalds d6748066ad Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (37 commits)
  MIPS: O32: Provide definition of registers ta0 .. ta3.
  MIPS: perf: Add Octeon support for hardware perf.
  MIPS: perf: Add support for 64-bit perf counters.
  MIPS: perf: Reorganize contents of perf support files.
  MIPS: perf: Cleanup formatting in arch/mips/kernel/perf_event.c
  MIPS: Add accessor macros for 64-bit performance counter registers.
  MIPS: Add probes for more Octeon II CPUs.
  MIPS: Add more CPU identifiers for Octeon II CPUs.
  MIPS: XLR, XLS: Add comment for smp setup
  MIPS: JZ4740: GPIO: Check correct IRQ in demux handler
  MIPS: JZ4740: GPIO: Simplify IRQ demuxer
  MIPS: JZ4740: Use generic irq chip
  MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines
  MIPS: Alchemy: kill au1xxx.h header
  MIPS: Alchemy: clean DMA code of CONFIG_SOC_AU1??? defines
  MIPS, IDE: Alchem, au1xxx-ide: Remove pb1200/db1200 header dep
  MIPS: Alchemy: Redo PCI as platform driver
  MIPS: Alchemy: more base address cleanup
  MIPS: Alchemy: rewrite USB platform setup.
  MIPS: Alchemy: abstract USB block control register access
  ...

Fix up trivial conflicts in:
	arch/mips/alchemy/devboards/db1x00/platform.c
	drivers/ide/Kconfig
	drivers/mmc/host/au1xmmc.c
	drivers/video/Kconfig
	sound/mips/Kconfig
2011-11-03 13:28:14 -07:00
Miklos Szeredi 6d6b77f163 filesystems: add missing nlink wrappers
Replace direct i_nlink updates with the respective updater function
(inc_nlink, drop_nlink, clear_nlink, inode_dec_link_count).

Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
2011-11-02 12:53:43 +01:00
Paul Gortmaker a0e5cc581b mtd: Add module.h to drivers users that were implicitly using it.
We are cleaning up the implicit presence of module.h that these
drivers are taking advantage of.  Fix them in advance of the
cleanup operation.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:12 -04:00
Paul Gortmaker f3bcc0179a mtd: Add export.h for EXPORT_SYMBOL/THIS_MODULE where needed
These two common macros will be no longer present everywhere.
Call out the include needs of them explicitly where required.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:11 -04:00
Wolfram Sang 48e546b7f2 mtd: tests: annotate as DANGEROUS in Kconfig
The tests may erase mtd devices, so annotate them as suggested per
coding style and add a paragraph to the help text as well.

Artem: amended the help test a bit.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
2011-10-30 22:33:30 +02:00
Wolfram Sang 7406060e29 mtd: tests: don't use mtd0 as a default
mtd tests may erase the mtd device, so force the user to specify which
mtd device to test by using the module parameter. Disable the default
(using mtd0) since this may destroy a vital part of the flash if the
module is inserted accidently or carelessly.

Reported-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
2011-10-30 14:31:04 +02:00
Paul Bolle 6be55f79a2 mtd: clean up usage of MTD_DOCPROBE_ADDRESS
Depending on whether MTD_DOCPROBE_ADVANCED is set or not,
MTD_DOCPROBE_ADDRESS will default to either 0x0000 or 0. That should
lead to (basically) identical code in docprobe.c. The current two
defaults should be merged.

And, while we're at it, if MTD_DOCPROBE is set MTD_DOCPROBE_ADDRESS will
always be set. (MTD_DOCPROBE_ADDRESS depends on MTD_DOCPROBE and it has
a default value.) So the check whether CONFIG_MTD_DOCPROBE_ADDRESS is
defined is unnecessary and should be dropped.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2011-10-30 14:22:36 +02:00
Linus Torvalds ca90666287 Merge branch 'gpio' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'gpio' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (43 commits)
  ARM: 7135/1: ep93xx: bring back missing <mach/gpio.h>
  ARM: 7104/1: plat-pxa: break out GPIO driver specifics
  ARM: 7103/1: plat-pxa: move PXA GPIO driver to GPIO subsystem
  ARM: 7042/3: mach-ep93xx: break out GPIO driver specifics
  ARM: 7101/1: arm/tegra: Replace <mach/gpio.h> with <mach/gpio-tegra.h>
  ARM: 7094/1: arm/tegra: Move EN_VDD_1V05_GPIO to board-harmony.h
  ARM: 7083/1: rewrite U300 GPIO to use gpiolib
  ARM: 7074/1: gpio: davinci: eliminate unused variable warnings
  ARM: 7063/1: Orion: gpio: add missing include of linux/types.h
  ARM: 7055/1: arm/tegra: mach/gpio.h: include linux/types.h to fix build
  ARM: 7054/1: arm/tegra: Delete custom gpio_to_irq, and irq_to_gpio
  ARM: 7053/1: gpio/tegra: Implement gpio_chip.to_irq
  ARM: 7052/1: gpio/tegra: Remove use of irq_to_gpio
  ARM: 7057/1: mach-pnx4008: rename GPIO header
  ARM: 7056/1: plat-nomadik: kill off <plat/gpio.h>
  ARM: 7050/1: mach-sa1100: delete irq_to_gpio() function
  ARM: 7049/1: mach-sa1100: move SA1100 GPIO driver to GPIO subsystem
  ARM: 7045/1: mach-lpc32xx: break out GPIO driver specifics
  ARM: 7044/1: mach-lpc32xx: move LPC32XX GPIO driver to GPIO subsystem
  ARM: 7043/1: mach-ixp2000: rename GPIO header
  ...

Fix up trivial conflicts in arch/arm/mach-u300/Kconfig manually
2011-10-27 08:39:10 +02:00
Manuel Lauss 3766386037 MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines
Now that no driver any longer depends on the CONFIG_SOC_AU1???  symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files.  Finally
delete them altogether from the Alchemy Kconfig file.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-10-24 23:34:24 +01:00
Manuel Lauss 50d5676eba MIPS: Alchemy: kill au1xxx.h header
No longer required

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/include/asm/mach-au1x00/au1xxx.h
2011-10-24 23:34:24 +01:00
John Crispin 2e5db86dd4 MIPS: Lantiq: Fix MTD registration of NOR device
The 2 functions add_mtd_partitions and del_mtd_partitions were renamed to
mtd_device_register and mtd_device_unregister.

Signed-of-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-10-20 15:00:17 +01:00
Brian Norris 23b1a99b87 mtd: nand: initialize ops.mode
Our `ops' information was converted to a local variable recently, and
apparently, old code relied on the fact that the global version was
often left in a valid mode. We can't make this assumption on local
structs, and we shouldn't be relying on a previous state anyway.

Instead, we initialize mode to 0 for don't-care situations (i.e., the
operation does not use OOB anyway) and MTD_OPS_PLACE_OOB when we want to
place OOB data.

This fixes a bug with nand_default_block_markbad(), where we catch on
the BUG() call in nand_fill_oob():

Kernel bug detected[#1]:
...
Call Trace:
[<80307350>] nand_fill_oob.clone.5+0xa4/0x15c
[<803075d8>] nand_do_write_oob+0x1d0/0x260
[<803077c4>] nand_default_block_markbad+0x15c/0x1a8
[<802e8c2c>] part_block_markbad+0x80/0x98
[<802ebc74>] mtd_ioctl+0x6d8/0xbd0
[<802ec1a4>] mtd_unlocked_ioctl+0x38/0x5c
[<800d9c60>] do_vfs_ioctl+0xa4/0x6e4
[<800da2e4>] sys_ioctl+0x44/0xa0
[<8001381c>] stack_done+0x20/0x40

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2011-10-16 15:04:00 +03:00
Andres Salomon d5de1907d0 mtd: provide an alias for the redboot module name
parse_mtd_partitions takes a list of partition types; if the driver
isn't loaded, it attempts to load it, and then it grabs the partition
parser.  For redboot, the module name is "redboot.ko", while the parser
name is "RedBoot".  Since modprobe is case-sensitive, attempting to
modprobe "RedBoot" will never work.  I suspect the embedded systems that
make use of redboot just always manually loaded redboot prior to loading
their specific nand chip drivers (or statically compiled it in).

Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org
2011-10-16 14:56:33 +03:00
Shaohui Xie 5f94913795 mtd: m25p80: don't probe device which has status of 'disabled'
On some platforms such as P3060QDS, has multiple spi flashes, but they are
not available at same time, so if their status is 'disabled', which is set
by u-boot, will not be probed.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2011-10-16 14:51:04 +03:00
Arnd Bergmann 57468a646e mtd: nand_h1900 never worked
This driver has been broken through all of git history and
cannot even be built. Better mark it as broken. Next stop is
removing from the tree.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2011-10-16 14:31:45 +03:00
Robert Jarzmik efa2ca73a7 mtd: Add DiskOnChip G3 support
Add support for DiskOnChip G3 chips. The support is quite
limited yet :
 - no flash writes/erases are implemented
 - ECC fixes are not implemented
 - powerdown is not implemented
 - IPL handling is not yet done

On the brighter side, the chip reading does work.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
2011-10-14 12:03:47 +03:00
Shaohui Xie 86a9893d08 mtd: m25p80: add EON flash EN25Q32B into spi flash id table
Add support for EON spi flash EN25Q32B, which is not listed in id table,
need to add it in the id table to support the EON flash.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-10-14 11:36:48 +03:00
Dan McGee 16f7eca587 mtd: mark block device queue as non-rotational
This is similar to what the nbd driver does, among others.

Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-10-14 11:22:48 +03:00
Axel Lin 1bba688b5a mtd: r852: make r852_pm_ops static
It is not used outside this driver so no need to make the symbol global.
Also make r852_suspend and r852_resume static.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-10-01 14:40:56 +03:00
Paul Bolle 395cf9691d doc: fix broken references
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.

Fix these broken references, sometimes by dropping the irrelevant text
they were part of.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-09-27 18:08:04 +02:00
Mikhail Kshevetskiy ada766e959 mtd: m25p80: add support for at25df321a spi data flash
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-26 10:05:25 +03:00
Wolfram Stering 5172ac1c6d mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
For NFC v1, the unlock end block address was 0x4000, which would only
unlock the first 32 blocks of the NAND flash.  Change that value to
0xffff to unlock all available blocks, as is done for NFC v21 as well.

Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-23 15:25:35 +03:00
Brian Norris 75b66d8ccd mtd: nand: switch `check_pattern()' to standard `memcmp()'
A portion of the `check_pattern()' function is basically a `memcmp()'.
Since it's possible for `memcmp()' to be optimized for a particular
architecture, we should use it instead.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-21 09:19:08 +03:00
Brian Norris 6d77b9d0af mtd: nand: invalidate cache on unaligned reads
In rare cases, we are given an unaligned parameter `from' in
`nand_do_read_ops()'. In such cases, we use the page cache
(chip->buffers->databuf) as an intermediate buffer before dumping to the
client buffer. However, there are also cases where this buffer is not
cleanly reusable. In those cases, we need to make sure that we
explicitly invalidate the cache.

This patch prevents accidental reusage of the page cache, and for me,
this solves some problems I come across when reading a corrupted BBT
from flash (NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).

Note: the rare "unaligned" case is a result of the extra BBT pattern +
version located in the data area instead of OOB.

Also, this patch disables caching on raw reads, since we are reading
without error correction. This is, obviously, prone to errors and should
not be cached.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-21 09:19:08 +03:00
Brian Norris 752ed6c5f8 mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
Updates to our default function for creating bad block patterns have
broken the "no OOB" feature. The NAND_BBT_NO_OOB option should not be
set while scanning for bad blocks, but we've been passing all BBT
options from nand_chip.bbt_options to the bad block scan. This causes us
to hit the:

	BUG_ON(bd->options & NAND_BBT_NO_OOB);

in create_bbt() when we scan the flash for bad blocks.

Thus, while it can be legal to set NAND_BBT_NO_OOB in a custom badblock
pattern descriptor (presumably with NAND_BBT_CREATE disabled?), we
should not pass it through in our default function.

Also, to help clarify and emphasize that the function creates bad block
patterns only (not, for example, table descriptors for locating
flash-based BBT), I renamed `nand_create_default_bbt_descr' to
`nand_create_badblock_pattern'.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-21 09:19:08 +03:00
Brian Norris dadc17a3e3 mtd: nand: wait to set BBT version
Because there are so many cases of checking, writing, and re-writing of
the bad block table(s), we might as well wait until the we've settled on
a valid, clean copy of the table. This also prevents us from falsely
incrementing the table version. For example, we may have the following:

  Primary table, with version 0x02
  Mirror table, with version 0x01
  Primary table has uncorrectable ECC errors

If we don't have this fix applied, then we will:

  Choose to read the primary table (higher version)
  Set mirror table version to 0x02
  Read back primary table
  Invalidate table because of ECC errors
  Retry readback operation with mirror table, now version 0x02
  Mirrored table reads cleanly
  Writeback BBT to primary table location (with "version 0x02")

However, the mirrored table shouldn't have a new version number.
Instead, we actually want:

  Choose to read the primary table (higher version)
  Read back primary table
  Invalidate table because of ECC errors
  Retry readback with mirror table (version 0x01)
  Mirrored table reads cleanly
  Set both tables to version 0x01
  Writeback BBT to primary table location (version 0x01)

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-21 09:19:08 +03:00
Brian Norris 623978de36 mtd: nand: scrub BBT on ECC errors
Now that `read_bbt()' returns ECC error codes properly, we handle those
codes when checking the integrity of our flash-based BBT.

The modifications can be described by this new policy:

*) On any uncorrected ECC error, we invalidate the corresponding table
   and retry our version-checking integrity logic.
*) On corrected bitflips, we mark both tables for re-writing to flash
   (a.k.a. scrubbing).

Current integrity checks (i.e., comparing version numbers, etc.) should
take care of all the cases that result in rescanning the device for bad
blocks or falling back to the BBT as found in the mirror descriptor.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-21 09:19:07 +03:00
Brian Norris 167a8d5250 mtd: nand: report ECC errors properly when reading BBT
Instead of just printing a warning when encountering ECC errors, we
should return a proper error status and print a more informative
warning. Later, we will handle these error messages in the upper layers
of the BBT scan.

Note that this patch makes our check for ECC error codes a little bit
more restrictive, leaving all unrecognized errors to the generic "else"
clause. This shouldn't cause problems and could even be a benefit.

This code is based on some findings reported by Matthieu Castet.

Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-21 09:19:07 +03:00
Brian Norris d57f40544a mtd: utilize `mtd_is_*()' functions
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-21 09:19:06 +03:00
Brian Norris b61bf5bbf6 mtd: nand: remove gotos in `check_create()'
This is a second step in restructuring `check_create()'. When we don't
rely on goto statements for our main functionality, the code will become
a little easier to manipulate.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 17:16:03 +03:00
Brian Norris c5e8ef9c21 mtd: nand: begin restructuring check_create
We will begin restructuring the code for check_create so that we can
make some important changes. For now, we should just begin to get rid of
some goto statements to make things cleaner. This is the first step of a
few, which are separated to make them easier to follow.

This step should just be a code refactor.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 17:15:56 +03:00
Brian Norris 596d74527a mtd: nand: fix style
Remove some extra spaces
Consistently use '0x' prefix for bitfield-like constants
Spelling: "aplies" -> "applies"

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 16:59:58 +03:00
Brian Norris 1196ac5a99 mtd: nand: remove unnecessary variable
`writeops' is unnecessary in the function `nand_update_bbt()'

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 16:57:49 +03:00
Brian Norris afa17de262 mtd: nand: do not ignore all ECC errors
There are a few reasons not to ignore ECC errors here.

First, mtd->read_oob is being called in raw mode, so there should be no
error correction in the first place.

Second, if we change this such that there *is* error correction in this
function, then we will want to pass the error message upward.

In fact, the code I introduced to "ignore ECC errors" would have been
better if it had just placed this test down in `scan_block_full()' in
the first place. We would like to ignore ECC errors when we are simply
checking for bad block markers (e.g., factory marked), but we may not
want to ignore ECC errors when scanning OOB for a flash-based BBT
pattern (in `scan_read_raw()'; note that the return codes from
`scan_read_raw()' are not actually handled yet).

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 16:48:49 +03:00
Brian Norris 105513cc4a mtd: nand: refactor scanning code
A few pieces of code are unnecessarily duplicated. For easier
maintenance, we should fix this.

This should have no functional effect.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 16:48:47 +03:00
Linus Walleij 3e2b82b907 mtd: drop Integrator flash map Kconfig
The integrator flash has been deleted, even from the Makefile.
Drop the Kconfig entry as well.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 16:35:47 +03:00
Brian Norris 19fb4341ad mtd: kill old field for `struct mtd_info_user'
The ecctype and eccsize fields have been obsolete for a while. Since they
don't have any users, we can kill them and leave padding in their place
for now.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:57:44 +03:00
Brian Norris 4a89ff885f mtd: nand: kill member `ops' of `struct nand_chip'
The nand_chip.ops field is a struct that is passed around globally with
no particular reason. Every time it is used, it could just as easily be
replaced with a local struct that is updated on each operation. So make
it local.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:57:44 +03:00
Brian Norris e99d8b089a mtd: add MEMWRITE ioctl
Implement a new ioctl for writing both page data and OOB to flash at the
same time. This ioctl is intended to be a generic interface that can
replace other ioctls (MEMWRITEOOB and MEMWRITEOOB64) and cover the
functionality of several other old ones, e.g., MEMWRITE can:

* write autoplaced OOB instead of using ECCGETLAYOUT (deprecated) and
  working around the reserved areas
* write raw (no ECC) OOB instead of using MTDFILEMODE to set the
  per-file-descriptor MTD_FILE_MODE_RAW
* write raw (no ECC) data instead of using MTDFILEMODE
  (MTD_FILE_MODE_RAW) and using standard character device "write"

This ioctl is especially useful for MLC NAND, which cannot be written
twice (i.e., we cannot successfully write the page data and OOB in two
separate operations). Instead, MEMWRITE can write both in a single
operation.

Note that this ioctl is not affected by the MTD file mode (i.e.,
MTD_FILE_MODE_RAW vs. MTD_FILE_MODE_NORMAL), since it receives its write
mode as an input parameter.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:56:25 +03:00
Brian Norris beb133fc16 mtd: rename MTD_MODE_* to MTD_FILE_MODE_*
These modes hold their state only for the life of their file descriptor,
and they overlap functionality with the MTD_OPS_* modes. Particularly,
MTD_MODE_RAW and MTD_OPS_RAW cover the same function: to provide raw
(i.e., without ECC) access to the flash. In fact, although it may not be
clear, MTD_MODE_RAW implied that operations should enable the
MTD_OPS_RAW mode.

Thus, we should be specific on what each mode means. This is a start,
where MTD_FILE_MODE_* actually represents a "file mode," not necessarily
a true global MTD mode.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:29:36 +03:00
Brian Norris 0612b9ddc2 mtd: rename MTD_OOB_* to MTD_OPS_*
These modes are not necessarily for OOB only. Particularly, MTD_OOB_RAW
affected operations on in-band page data as well. To clarify these
options and to emphasize that their effect is applied per-operation, we
change the primary prefix to MTD_OPS_.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:28:59 +03:00
Brian Norris 905c6bcdb4 mtd: move mtd_oob_mode_t to shared kernel/user space
We will want to use the MTD_OOB_{PLACE,AUTO,RAW} modes in user-space
applications through the introduction of new ioctls, so we should make
this enum a shared type.

This enum is now anonymous.

Artem: tweaked the patch.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:26:20 +03:00
Brian Norris c46f6483d2 mtd: support reading OOB without ECC
This fixes issues with `nanddump -n' and the MEMREADOOB[64] ioctls on
hardware that performs error correction when reading only OOB data. A
driver for such hardware needs to know when we're doing a RAW vs. a
normal write, but mtd_do_read_oob does not pass such information to the
lower layers (e.g., NAND). We should pass MTD_OOB_RAW or MTD_OOB_PLACE
based on the MTD file mode.

For now, most drivers can get away with just setting:

  chip->ecc.read_oob_raw = chip->ecc.read_oob

This is done by default; but for systems that behave as described above,
you must supply your own replacement function.

This was tested with nandsim as well as on actual SLC NAND.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:13:38 +03:00
Brian Norris 9ce244b3fb mtd: support writing OOB without ECC
This fixes issues with `nandwrite -n -o' and the MEMWRITEOOB[64] ioctls
on hardware that writes ECC when writing OOB. The problem arises as
follows: `nandwrite -n' can write page data to flash without applying
ECC, but when used with the `-o' option, ECC is applied (incorrectly),
contrary to the `--noecc' option.

I found that this is the case because my hardware computes and writes
ECC data to flash upon either OOB write or page write. Thus, to support
a proper "no ECC" write, my driver must know when we're performing a raw
OOB write vs. a normal ECC OOB write. However, MTD does not pass any raw
mode information to the write_oob functions.  This patch addresses the
problems by:

1) Passing MTD_OOB_RAW down to lower layers, instead of just defaulting
   to MTD_OOB_PLACE
2) Handling MTD_OOB_RAW within the NAND layer's `nand_do_write_oob'
3) Adding a new (replaceable) function pointer in struct ecc_ctrl; this
   function should support writing OOB without ECC data. Current
   hardware often can use the same OOB write function when writing
   either with or without ECC

This was tested with nandsim as well as on actual SLC NAND.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:18 +03:00
Huang Shijie 10a2bcae99 mtd: add the common code for GPMI-NAND controller driver
These files contain the common code for the GPMI-NAND driver.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:18 +03:00
Huang Shijie 157550ff77 mtd: add GPMI-NAND driver in the config and Makefile
add the GPMI-NAND driver in the relevant Kconfig and Makefile in the MTD.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:18 +03:00
Huang Shijie 45dfc1a09a mtd: add helper functions library and header files for GPMI NAND driver
bch-regs.h : registers file for BCH module
gpmi-regs.h: registers file for GPMI module
gpmi-lib.c: helper functions library.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:18 +03:00
Jason Liu 4d523b60ef mtd: check parts pointer before using it
The code has the check for parts but it called after kmemdup,
kmemdup(parts, sizeof(*parts) * nr_parts,...)
if (!parts)
	return -ENOMEM

In fact, we need check parts before safely using it.
and we also need check the real_parts to make sure kmemdup
allocation sucessfully.

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:18 +03:00
Brian Norris 305b93f180 mtd: do not assume oobsize is power of 2
Previous generations of MTDs all used OOB sizes that were powers of 2,
(e.g., 64, 128). However, newer generations of flash, especially NAND,
use irregular OOB sizes that are not powers of 2 (e.g., 218, 224, 448).
This means we cannot use masks like "mtd->oobsize - 1" to assume that we
will get a proper bitmask for OOB operations.

These masks are really only intended to hide the "page" portion of the
offset, leaving any OOB offset intact, so a masking with the writesize
(which *is* always a power of 2) is valid and makes more sense.

This has been tested for read/write of NAND devices (nanddump/nandwrite)
using nandsim and actual NAND flash.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:17 +03:00
Jason Liu c97926dd8d mtd: mxc_nand: add mx53 NFC driver support
This has already been tested with Samsung NAND: K9LAG08U0M
on MX53EVK board, ubi/ubifs has already been tested OK too.

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:17 +03:00
Julia Lawall 38ca6ebc72 mtd: bcm_umi_nand: clean up error handling code
Convert error handling code to use gotos.  At the same time, this adds
calls to kfree and iounmap in a few cases where they were overlooked.

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:17 +03:00
Michael Hench f975c6bcb0 mtd: eLBC NAND: update ecc_stats.corrected when lteccr available
Signed-off-by: Michael Hench <MichaelHench@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:17 +03:00
Jonghwan Choi 4aa10626ad mtd: s3c2410 nand: Remove uncessary null check
clk_get() return a pointer to the struct clk or an ERR_PTR().

Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:17 +03:00
Brian Norris 92394b5c2b mtd: spelling fixes
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Jan Weitzel 46a00d83ff mtd: use MTD_NAND_OMAP2 for OMAP4
use MTD_NAND_OMAP2 also for OMAP4 arch.
testes with omap4430

Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Brian Norris 022bba8a30 mtd: Kbuild: remove reference to MTD_PARTITIONS
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Brian Norris 278981c541 mtd: cleanup last uses of MTD_DEBUG config macros
Some messages that were tied to CONFIG_MTD_DEBUG_VERBOSE can now simply
be enabled using dynamic debugging features, if necessary. There's no
need for special debugging functions here.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Brian Norris 87ed114bb2 mtd: remove CONFIG_MTD_DEBUG
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Brian Norris e6453521ed mtd: pcmciamtd: remove custom DEBUG() function
We don't need a custom DEBUG() macro here. Just use the built-in kernel
code with dynamic debugging features.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Brian Norris 0a32a10264 mtd: cleanup style on pr_debug messages
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Brian Norris 289c052221 mtd: replace DEBUG() with pr_debug()
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic
debugging feature is a generic kernel feature that provides more
flexibility.

(See Documentation/dynamic-debug-howto.txt)

Also fix some punctuation, indentation, and capitalization that went
along with the affected lines.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:16 +03:00
Brian Norris d037021953 mtd: nand: style fixups in pr_* messages
This is a cleanup of some punctuation, indentation, and capitalization
on the lines affected affected by the last patch.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:15 +03:00
Brian Norris 9a4d4d6901 mtd: nand: convert printk() to pr_*()
Instead of directly calling printk, it's simpler to use the built-in
pr_* functions. This shortens code and allows easy customization through
the definition of a pr_fmt() macro (not used currently). Ideally, we
could implement much of this with dev_* functions, but the MTD subsystem
does not necessarily register all its master `mtd_info.dev` device, so
we cannot use dev_* consistently. See:
http://lists.infradead.org/pipermail/linux-mtd/2011-July/036950.html

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:15 +03:00
Brian Norris a0f5080ecc mtd: nand: change KERN_DEBUG to KERN_INFO
Soon we will change many printk statements into pr_* statements, i.e.,
'printk(KERN_INFO, ...)' becomes 'pr_info(...)'. However, this means that
KERN_DEBUG messages will become pr_debug() statements and therefore will
not be activated by default - they must be enabled using dynamic debug.
So, for important DEBUG messages, we will simply upgrade these to INFO
so that they appear by default.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:15 +03:00
Shawn Guo b94e757c4b mtd: dataflash: add device tree probe support
It adds device tree probe support for mtd_dataflash driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:15 +03:00
Lei Wen f3c8cfc237 mtd: pxa3xx_nand: enable multiple chip select support
Current pxa3xx_nand controller has two chip select which
both be workable. This patch enable this feature.

Update platform driver to support this feature.

Another notice should be taken that:
When you want to use this feature, you should not enable the
keep configuration feature, for two chip select could be
attached with different nand chip. The different page size
and timing requirement make the keep configuration impossible.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-09-11 15:02:15 +03:00
Lei Wen d456882b41 mtd: pxa3xx_nand: sperate each chip individual info
For support two chip select, we seperate chip specific info in this
patch.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-09-11 15:02:15 +03:00
Lei Wen da675b4ef2 mtd: pxa3xx_nand: convert all printk into dev_*
Also add missed warning message.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:15 +03:00
Lei Wen 051fc41c2e mtd: pxa3xx_nand: enhance suspend and resume routine
This patch add protection on the suspend&resume path to prevent
some unexpected behavior, like interrupt occur at the very second
of resume back and it don't follow normal command path, which lead
to bug.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-09-11 15:02:15 +03:00
Mike Hench 52a474de0a mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly.  Remove this useless (and potentially problematic)
block of code.

Signed-off-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:15 +03:00
Nicolas Ferre fb5427508a mtd: atmel_nand: optimize read/write buffer functions
For PIO NAND access functions, we use the features of the SMC:
- no need to take into account the NAND bus width: SMC will deal with this
- use of an IO memcpy on the NAND chip-select space is able to generate
  proper SMC behavior.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:15 +03:00
Liu Shuo 57b078a09b mtd: nand: don't free the global data too early
The global data fsl_lbc_ctrl_dev->nand don't have to be freed in
fsl_elbc_chip_remove(). The right place to do that is in fsl_elbc_nand_remove()
if elbc_fcm_ctrl->counter is zero.

Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Axel Lin a751d3155d mtd: fsl_upm: fix a memory leak in fun_chip_init error path
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Nicolas Ferre 201ab536ac mtd: atmel_nand: fix wrong use of 0 as NULL
Fixing this error:
atmel_nand.c:718:20: warning: Using plain integer as NULL pointer

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Matthieu CASTET 08c248fbe2 mtd: nand_flash_detect_onfi propagate busw info
there is a bug in nand_flash_detect_onfi, busw need to be passed
by pointer to return it.

Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Brian Norris c478d7e449 mtd: edit NAND-related comment
This comment was unclear regarding which NAND functions do and do not
support ECC on the spare area. This update should reflect the current
status of the NAND system but can be updated if changes are made in
the standard functions.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Brian Norris 003bc47922 mtd: tests: ignore corrected bitflips in OOB on mtd_readtest
read_oob may now return ECC error codes. If the code is -EUCLEAN, then
we can safely ignore the error as a corrected bitflip.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Brian Norris 903cd06cd6 mtd: nand: ignore ECC errors for simple BBM scans
Now that nand_do_readoob() may return -EUCLEAN or -EBADMSG on ECC errors,
we need to handle the return value specially in some cases.

When scanning for simple bad block markers, reacting to an ECC error is
not very useful, as we assume that the relevant markers are still
non-0xFF for true bad blocks.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Dmitry Eremin-Solenikov 9786f6e68a mtd: ofpart: add ofoldpart alias
ofpart.ko also provides ofoldpart MTD parser. Add respective
MODULE_ALIAS("ofoldpart"); declaration.

Artem: improve the comment

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Brian Norris 041e4575f0 mtd: nand: handle ECC errors in OOB
While the standard NAND OOB functions do not do ECC on the spare area,
it is possible for a driver to supply its own OOB ECC functions (e.g., HW
ECC). nand_do_read_oob should act like nand_do_read_ops in checking the
ECC stats and returning -EBADMSG or -EUCLEAN on uncorrectable errors or
correctable bitflips, respectively. These error codes could be used in
flash-based BBT code or in YAFFS, for example.

Doing this, however, messes with the behavior of mtd_do_readoob. Now,
mtd_do_readoob should check whether we had -EUCLEAN or -EBADMSG errors
and discard those as "non-fatal" so that the ioctls can still succeed
with (possibly uncorrected) data.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2011-09-11 15:02:14 +03:00
Dmitry Eremin-Solenikov d6137badef mtd: make ofpart buildable as a separate module
As ofpart now uses a standard mtd partitions parser interface, make it
buildable as a separate module. Also provide MODULE_DESCRIPTION and
MODULE_AUTHOR for this module.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:13 +03:00
Brian Norris 7854d3f749 mtd: spelling, capitalization, uniformity
Therefor -> Therefore
[Intern], [Internal] -> [INTERN]
[REPLACABLE] -> [REPLACEABLE]
syndrom, syndom -> syndrome
ecc -> ECC
buswith -> buswidth
endianess -> endianness
dont -> don't
occures -> occurs
independend -> independent
wihin -> within
erease -> erase
blockes -> blocks
...

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2011-09-11 15:02:13 +03:00