Add set block count command support for close ended multiblock read/write.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
split start dma function into setup and start dma to keep track of
host_cookie when cmd23 support is enabled along with async request.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
mrq is not populated for set block count(cmd23) command.
Use block read/write mmc_commond pointer for request done and
avoid NULL pointer access in error case for sbc (cmd23).
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
clk_get_rate throws DEBUG_LOCKS_WARN_ON(in_interrupt()) warning
if called from interrupt context.
use cached clock rate in set_data_timeout, so that
set_data_timeout can be called from interrupt context.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
Remove redundant reset done check since omap hwmod layer ensures IP reset.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chris Ball <chris@printf.net>
of_get_hsmmc_pdata returns a pointer, returning NULL is invalid,
return ERR_PTR for error case.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chris Ball <chris@printf.net>
remove pbias workaround
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
Enable REGULATOR_PBIAS needed for SD card on most OMAPs.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
Add pbias regulator node as a child of system control
module - syscon.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
In DT case, PBAIS registers are programmed via regulator,
use regulator APIs to control PBIAS.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
pbias register controls internal power supply to sd card i/o pads
in most OMAPs (OMAP2-5, DRA7).
Control bits for selecting voltage level and
enabling/disabling are in the same PBIAS register.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@linaro.org>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
handle vcc and vcc_aux independently to reduce indent.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
Use devm_regulator API, while at it use
devm_regulator_get_optional for optional vmmc_aux supply
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
This should probably be done implicitly through mmc_of_parse(), but that
doesn't play well along with the multi-slot model the hsmmc driver
features. Hence, for now, do it manually. The properties are already
documented in Documentation/devicetree/bindings/mmc/mmc.txt.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
MMC1 is the only MMC interface available on the platform. Further,
since the platform is based on older revision of SoC which is not
capable of doing multi-block reads, mark it with compatibility for the
same and add pinmux to ensure that all relevant pins are configured
for non-MMC boot mode.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
When device is booted using devicetree, platforms impacted by Erratum
2.1.1.128 is not detected easily in the mmc driver. This erratum
indicates that the module cannot do multi-block transfers. Platforms
such as LDP which use OMAP3 ES revision prior to ES3.0 are impacted by
this.
Provide a new compatible property "ti,omap3-pre-es3-hsmmc" to allow
driver to determine if driver needs to implement quirks associated
with the specific module version (primarily because the IP revision
information is not sufficient for the same).
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
Static checkers complain that testing for both "next" and "!next" is
duplicative.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
Fix the following build errors:
drivers/mmc/host/dw_mmc-k3.c: In function ‘dw_mci_k3_suspend’:
drivers/mmc/host/dw_mmc-k3.c:58:2: error: implicit declaration of
function ‘dw_mci_suspend’ [-Werror=implicit-function-declaration]
ret = dw_mci_suspend(host);
^
drivers/mmc/host/dw_mmc-k3.c: In function ‘dw_mci_k3_resume’:
drivers/mmc/host/dw_mmc-k3.c:76:2: error: implicit declaration of
function ‘dw_mci_resume’ [-Werror=implicit-function-declaration]
return dw_mci_resume(host);
^
drivers/mmc/host/dw_mmc-k3.c: At top level:
drivers/mmc/host/dw_mmc-k3.c:53:12: warning: ‘dw_mci_k3_suspend’ defined
but not used [-Wunused-function]
static int dw_mci_k3_suspend(struct device *dev)
^
drivers/mmc/host/dw_mmc-k3.c:65:12: warning: ‘dw_mci_k3_resume’ defined
but not used [-Wunused-function]
static int dw_mci_k3_resume(struct device *dev)
^
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
This patch modifies sdhci_s3c_consider_clock() to fail if bus clock
being considered can not provide frequency lower or equal requested,
instead of returning the lowest supported.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Currently the driver assumes at probe that controller is configured for
last valid enumerated bus clock. This assumption is completely wrong, as
there is no way to ensure such configuration until the hardware gets
first configured (by calling sdhci_s3c_set_clock()).
This patch modifies the driver to set current clock at probe to unknown
state (represented by negative value) and make sure that the hardware
gets actually configured to selected clock in sdhci_s3c_set_clock().
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
This patch reimplements functions calculating minimum and maximum clock
rates to leverage clock rate cache introduced by previous patches.
In addition, the calculation is simplified to just comparing input
clock rates (max case) or input clock rates divided by maximum divisor
(min case), which is basically what the original code did, but with much
more unnecessary work.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
IS_ERR() must be used to make sure that not a valid clock was returned
by clk_get() and company.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
To fix scheduling while atomic happening in sdhci_s3c_set_clock() caused
by calling clk_get_rate() that might sleep, this patch modifies the
driver to cache rates of all bus clocks at probe time and then only use
those cache values.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Current implementation of sdhci_s3c_consider_clock() is highly
inefficient due to multiple integer divisions by variable performed in a
loop. Since only divisors that are powers of two are considered, this
patch replaces them with respective shifts, removing all the integer
divisions.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Introduce "altr,socfpga-dw-mshc" to enable Altera's SOCFPGA platform
specific implementation of the dw_mmc driver.
Also add the "syscon" binding to the "altr,sys-mgr" node. The clock
driver can use the syscon driver to toggle the register for the SD/MMC
clock phase shift settings.
Finally, fix an indentation error for the sysmgr node.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Chris Ball <chris@printf.net>
Like the rockchip, Altera's SOCFPGA platform specific implementation of the
dw_mmc driver requires using the HOLD register for SD commands. This patch
renames dw_mci_rockchip_prepare_command to dw_mci_pltfm_prepare_command so
that SOCFPGA and Rockchip can use it.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
It turns now that the only really platform specific code that is needed for
SOCFPGA is using the SDMMC_CMD_USE_HOLD_REG in the prepare_command function.
Since the Rockchip already has this functionality, re-use the code that is
already in dw_mmc-pltfm.c.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
If mrq->sbc is not NULL but data->stop happens to be NULL,
it will lead to NULL pointer dereferencing. Avoid this by
having a NULL check for data->stop.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Commit c02cecb92e ("ARM: orion: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Commit 1ef21f6343 ("ARM: msm: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Commit 0976f16d ("mmc: dw_mmc: add support tuning scheme") introduced
the execute_tuning hook but did not add its description for kernel docs.
Update the same.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
pdata could be NULL if cd_gpio = -1. Dereference pdata only
if it is not NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
'of_id' is dereferenced before NULL pointer check. Move it to
after the check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <chris@printf.net>
sizeof should be of the parent structure type.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Enable the external clock needed by the host controller during the
probe and disable it during the remove.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The ux500 variants have HW busy detection support, which is indicated
by the busy_detect flag. For these variants let's enable the
MMC_CAP_WAIT_WHILE_BUSY flag and add the support for it.
The mmc core will provide the RSP_BUSY command flag for those requests
we should care about busy detection. Regarding the max_busy_timeout,
the HW don't support busy detection timeouts so at this initial step
let's make it simple and set it to zero to indicate we are able to
support any timeout.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
In case of a read operation both MCI_CMDRESPEND and MCI_DATAEND can be
set in the status register when entering the interrupt handler. This is
due to that the card start sending data before the host has
acknowledged the command response.
To resolve the issue for this scenario, we must start by handling the
CMD irq instead of the DATA irq. The reason is beacuse the completion
of the DATA irq will not respect the current command and then causing
it to be garbled.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
When sending a stop command at the recovery path, use a R1B response
when the failing data request are a WRITE. Thus we also care about the
busy detection completion in this case.
For a failing READ request, we use a R1 response for the stop command,
since we don't need to care about busy detection in this case.
To align behavior between hosts supporting MMC_CAP_WAIT_WHILE_BUSY and
those who are not, we add a CMD13 polling method for the card's status.
We also respect whether the host has specified the max_busy_timeout,
which means we may fallback to CMD13 polling if the timeout is greater
than what the host are able to support.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Currently for write request we don't trust the hw busy detection to be
fully handled by host, thus we also poll the card's status until we see
it's gets out of the busy state.
Still there are scenarios where it will a benefit to trust the hw busy
detection done by the host, since no additional polling is needed.
Let's prepare card_busy_detect() to be able to handle this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
To complete a data write request we poll for the card's status register
by sending CMD13. The are other scenarios when this polling method are
needed, which is why we here moves this code to it's own function. No
functional change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
While using open ended transmission and thus ending the transfer by
sending a stop command, we shall use R1B only for writes and R1 shall
be used for reads. Previously R1B were used in both cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
When sending the sleep command for host drivers supporting
MMC_CAP_WAIT_WHILE_BUSY, we need to confirm that max_busy_timeout is
big enough comparing to the sleep timeout specified from card's
EXT_CSD. If this isn't case, we use a R1 response instead of R1B and
fallback to use a delay instead.
Do note that a max_busy_timeout set to zero by the host, is interpreted
as it can cope with whatever timeout the mmc core provides it with.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Conform to the eMMC spec and use the CMD6 generic timeout from the
EXT_CSD register, when switching to HS200 mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
If the host controller supports busy detection in HW, we expect the
MMC_CAP_WAIT_WHILE_BUSY to be set. Likewise the corresponding
host->max_busy_timeout should reflect the maximum busy detection
timeout supported by the host.
Previously we expected a host that supported MMC_CAP_WAIT_WHILE_BUSY to
cope with any timeout, which just isn't feasible due to HW limitations.
For most switch operations, R1B responses are expected and thus we need
to check for busy detection completion. To cope with cases where the
requested busy detection timeout is greater than what the host are able
to support, we fallback to use a R1 response instead. This will prevent
the host from doing HW busy detection.
In those cases, busy detection completion is handled by polling the for
the card's status using CMD13. This is the same mechanism used when the
host doesn't support MMC_CAP_WAIT_WHILE_BUSY.
Do note, a host->max_busy_timeout set to zero, is interpreted by the
mmc core as it don't know what the host supports. It will then provide
the host with whatever timeout the mmc core finds suitable.
For some cases the mmc core has unfurtunate no clue of what timeout to
use. In these cases we provide the host with a timeout value of zero,
which the host may interpret as use whatever timeout it finds suitable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Instead of using several references to card->host, let's use a local
variable. That means we can remove the BUG_ON verifications for the
same pointers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Balaji T K