The l2cap_conn->src and l2cap_conn->dst pointers are no longer in use
and so just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The l2cap_conn->src and l2cap_conn->dst addresses are just a pointers
to hci_conn structure. Use hci_conn->hdev->bdaddr and hci_conn->dst
directly instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The l2cap_conn->src and l2cap_conn->dst addresses are just a pointer
to hci_conn->hdev->bdaddr and hci_conn->dst structures. Use the data
provided by hci_conn directly. This is done for hci_conn->dst_type
already anyway and with this change it makes it a lot clearer were
the address information comes from.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The l2cap_conn->dst address is just a pointer into the hci_conn->dst
structure. Use hci_conn->dst directly instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The unicast connectionless data reception feature is actually support
and has been supported all along. Mark it as supported in the L2CAP
features bitmask.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The implementation actually supports the L2CAP connectionless data
channel. So set it as supported in the fixed channels bitmask.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The PSM 0x0021 is dedicated to the 3D profile and has permission to
use security mode 4 level 0 for L2CAP connectionless unicast data
transfers.
When establishing a L2CAP connectionless channel on PSM 0x0021, it
will no longer force Secure Simple Pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The exception for certain PSM channels when it comes to security
mode 4 level 0 should only be checked when actually a connection
oriented channel is established.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The put_unaligned() for setting the PSM is missing the (__le16 *)
cast. Without this, the PSM information transmitted over the air
are bogus.
In addition, print the used PSM value in the debug message so this
becomes easier to debug in the future.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The 1st generation of BlueFRITZ! devices from AVM Berlin pretend
to be HCI version 1.2 controllers, but they are not. They are simple
Bluetooth 1.1 devices.
Since this company never created any newer controllers, it is safe
to use the manufacturer ID instead of an USB quirk.
< HCI Command: Read Page Scan Activity (0x03|0x001b) plen 0
> HCI Event: Command Complete (0x0e) plen 8
Read Page Scan Activity (0x03|0x001b) ncmd 1
Status: Success (0x00)
Interval: 1280.000 msec (0x0800)
Window: 21.250 msec (0x0022)
< HCI Command: Read Page Scan Type (0x03|0x0046) plen 0
> HCI Event: Command Status (0x0f) plen 4
Read Page Scan Type (0x03|0x0046) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding support for MGMT_OP_SET_SCAN_PARAMS command the addition
to the supported commands list has been forgotten. This is needed
for userspace to detect if the command is supported or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is not allowed to enable high speed support when Secure Simple
Pairing is not available or disabled.
However the support for high speed gets advertised on a controller
that does not even support Secure Simple Pairing. Since there is
no way to enable high speed support on such a controller, do not
even advertise its support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Really early versions of the Bluetooth specification were unclear
with the behavior of HCI Reset for USB devices. They assumed that
also an USB reset needs to be issued. Later Bluetooth specifications
cleared this out and it is safe to call HCI Reset without affecting
the transport.
For old devices that misbehave, the HCI_QUIRK_RESET_ON_CLOSE quirk
was introduced to postpone the HCI Reset until the device was no
longer in use.
One of these devices is the Digianswer BPA-105 Bluetooth Protocol
Analyzer. The only problem now is that with the quirk set, the
HCI Reset is also executed at the end of the setup phase. So the
controller gets configured and then it disconnects from the USB
bus, connects again, gets configured and of course disconnects
again. This game goes on forever.
For devices that need HCI_QUIRK_RESET_ON_CLOSE it is important
that the HCI Reset is not executed after the setup phase. In
specific when HCI_AUTO_OFF is set, do not call HCI Reset when
closing the device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The scan interval and window parameters are used for LE passive
background scanning and connection establishment. This allows
userspace to change the values.
These two values should be kept in sync with whatever is used for
the scan parameters service on remote devices. And it puts the
controlling daemon (for example bluetoothd) in charge of setting
the values.
Main use case would be to switch between two sets of values. One
for foreground applications and one for background applications.
At this moment, the values are only used for manual connection
establishment, but soon that should be extended to background
scanning and automatic connection establishment.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The scan interval and window for LE passive scanning and connection
establishment should be configurable on a per controller basis. So
introduce a setting that later on will allow modifying it.
This setting does not affect LE active scanning during device
discovery phase. As long as that phase uses interleaved discovery,
it will continuously scan.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The ath3k_table[] and ath3k_blist_tbl[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bpa10x_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb_table[] and blacklist_table[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of vhci_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of hci_uart_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of dtl1_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btuart_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btmrvl_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bt3c_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bluecard_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bfusb_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The function h4_check_data_len() is actually not used. So just
remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of hci_send_frame() is never checked. So just make
this function void and print an error when the hdev->send driver
callback returns a negative value.
Having the error printed is actually an improvement over the
current situation where any driver error just gets ignored.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of hci_send_frame must be always valid. If the hdev
is not valid, it would not even make it to this stage. The callers
will have already accessed hdev at that point many times.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The assignement of skb->dev is done all over the place. So it makes it
hard to eventually get rid of it. Move it all in one central place so
it gets assigned right before calling hdev->send driver callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The smp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The a2mp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The amp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since there is no use of hdev->ioctl by any Bluetooth driver since
ever, so just lets remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btmrvl_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The dtl1_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btuart_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt3c_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bluecard_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The legacy ioctls for device specific commands including inquiry are
not support by AMP controllers. So just reject them right away instead
of trying to send the HCI command and wait for failure from the
actual hardware.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.
In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When checking for the current number of LE connections, use
hci_conn_num() function instead of a full blown lookup within
the connection hash or direct access of the counters.
In the case of re-enabling advertising, it is more useful to
check for any connection attempt or existing connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The function declaration goes over 80 characters, so break it down.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI_SETUP flag is set the controller has not yet been announced
over mgmt and therefore doesn't exist from that perspective. If we
nevertheless get a mgmt command for it we should respond with the
appropriate INVALID_INDEX error.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The l2cap_recv_frame function is expected to take ownership and
eventually free the skb passed to it. We need to ensure that the
conn->rx_skb pointer is no longer reachable when calling
l2cap_recv_frame so that no other function, such as l2cap_conn_del, may
think that it can free conn->rx_skb.
An actual situation when this can happen is when smp_sig_channel (called
from l2cap_recv_frame) fails and l2cap_conn_del gets called as a
consequence. The l2cap_conn_del function would then try to free
conn->rx_skb, but as the same skb was just passed to smp_sig_channel and
freed we get a double-free.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The support for Bluetooth High Speed can only be enabled on controllers
where also Secure Simple Pairing has been enabled. Trying to enable
high speed when SSP is disabled will result into an error. Disabling
SSP will at the same time disable high speed as well.
It is required to enforce this dependency on SSP since high speed
support is only defined for authenticated, unauthenticated and
debug link keys. These link key types require SSP.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann