With the STM32 thermal peripheral, it is not possible to dump the
temperature that has caused the interrupt.
When the temperature reaches the low threshold, we generally read
a temperature that is a little bit higher than the low threshold.
This maybe due to sampling precision, and also because the CPU becomes
hotter when it quits WFI mode.
In that case, the framework does not change the trip points. This leads
to a lot of low threshold interrupts.
The fix is to set the low threshold value 0.5 degrees Celsius
below the actual request.
The problem is not so frequent with the high threshold and it would
no be a good idea to set the threshold value higher than the request.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-7-p.paillet@st.com
Change the way of computing to avoid rounds by 1 or 2 degrees.
Also simplify the sampling time management that is hard-coded
to maximum value during probe.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-6-p.paillet@st.com
Let the thermal framework handle the trip points instead
of custom code inside the driver. This is backward compatible,
simplifies the driver and offers the possibility to the user
to set any trip point he needs.
stm_thermal_set_trips callback that is registered to
set_trips ops to handle the low and high thresholds and replaces
stm_thermal_set_threshold and stm_thermal_update_threshold functions.
modify irq enable to handle the thresholds.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-5-p.paillet@st.com
In case of CPU reset, the interrupts could be enabled at boot time.
Disable interrupts and clear flags.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-4-p.paillet@st.com
Be sure get_temp returns an error while disabling or enabling the device.
Set THERMAL_DEVICE_ENABLED state at the end of power on function.
Set THERMAL_DEVICE_DISABLED state at the beginning of power off function.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-3-p.paillet@st.com
When devm_thermal_zone_of_sensor_register() is called from
hwmon_thermal_add_sensor() it is possible that the relevant sensor is
missing an OF node. In this case thermal_zone_of_sensor_register() returns
-EINVAL which causes hwmon_thermal_add_sensor() to fail as well. This patch
changes relevant return code of thermal_zone_of_sensor_register() to
-ENODEV, which is tolerated by hwmon_thermal_add_sensor().
Here is a particular case of such behaviour: the Marvell ethernet PHYs
driver registers hwmon device for the built-in temperature sensor (see
drivers/net/phy/marvell.c). Since the sensor doesn't have associated OF
node devm_hwmon_device_register() returns error which ultimately causes
failure of the PHY driver's probe function.
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20190827143952.19591-1-pmamonov@gmail.com
The hardware manual states that the operation of the sensor is not
guaranteed with temperatures above 125°C, not that the readings are
invalid. Remove the bound check and try to deliver temperature readings
even if we are outside the guaranteed operation range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200117160554.3812787-3-niklas.soderlund+renesas@ragnatech.se
The hardware manual states that the operation of the sensor is not
guaranteed outside the range of -45°C to 125°C, not that the readings
are invalid. Remove the bound check and try to deliver temperature
readings even if we are outside the guaranteed operation range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200117160554.3812787-2-niklas.soderlund+renesas@ragnatech.se
Add Comet Lake to the list of the platforms to support intel_pch_thermal
driver.
Cc: Zhang rui <rui.zhang@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191211200043.4985-1-gayatri.kammela@intel.com
The driver calls pci_request_regions() in probe and uses
pci_release_regions() in probe failure.
However, it calls pci_release_region() in remove, which does
match the other two calls.
Use pci_release_regions() instead to unify them.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191206075531.18637-1-hslester96@gmail.com
Since we do not have interrupts on BCM7216, we cannot have trip point
crossing, the thermal subsystem expects us to provide a NULL set_trips
operation in that case, so make it possible to provide per-process
thermal_zone_of_device_ops
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-7-f.fainelli@gmail.com
If we are successful grabbing the interrupt resource, then register an
interrupt handler, this makes it easier to support the interrupt as
being optional, which is it for 7216.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-6-f.fainelli@gmail.com
Match the 7216 compatible string in order to derive the correct 16nm
process thermal parameters to obtain correct readings.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-5-f.fainelli@gmail.com
The driver is currently assuming that it is operating with a 28nm
process chip, which has a specific formula to convert temperature to a
code and vice versa. Update the code to support providing two key
values: offset and multiplier to derive the correct formulas.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-3-f.fainelli@gmail.com
At the time the brcmstb_thermal driver and its binding were merged, the
DT binding did not make the coefficients properties a mandatory one,
therefore all users of the brcmstb_thermal driver out there have a non
functional implementation with zero coefficients. Even if these
properties were provided, the formula used for computation is incorrect.
The coefficients are entirely process specific (right now, only 28nm is
supported) and not board or SoC specific, it is therefore appropriate to
hard code them in the driver given the compatibility string we are
probed with which has to be updated whenever a new process is
introduced.
We remove the existing coefficients definition since subsequent patches
are going to add support for a new process and will introduce new
coefficients as well.
Fixes: 9e03cf1b2d ("thermal: add brcmstb AVS TMON driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-2-f.fainelli@gmail.com
rcar_thermal_update_temp() takes a mutex, so it is always called in a
context that can sleep. Hence replace the 300 µs busy loop by a call to
usleep_range(), to allow other threads to run.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200115125417.5263-1-geert+renesas@glider.be
This adds the thermal sensor driver for the Broadcom BCM2711 SoC,
which is placed on the Raspberry Pi 4. The driver only provides
SoC temperature reading so far.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-3-git-send-email-stefan.wahren@i2se.com
The cp_ft_flag variable is not used after initialization, so delete
it. After that, THS_EFUSE_CP_FT_MASK, THS_EFUSE_CP_FT_BIT and
THS_CALIBRATION_IN_FT are not needed, so delete them.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200112180925.23705-1-tiny.windzz@gmail.com
sparse returns a warning:
"drivers/thermal/sun8i_thermal.c:341:60: sparse: sparse: Using plain
integer as NULL pointer".
Fix it by replacing the zero integer by a NULL pointer.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200112171318.23025-1-tiny.windzz@gmail.com
According to the spec, r40 has 2 thermal sensors.
Sensor0 located in the CPU, another in the GPU.
Fixes: dccc5c3b6f ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-on: sun8i-r40-bananapi-m2-ultra
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200106174639.20862-1-tiny.windzz@gmail.com
* acpi-battery:
ACPI / battery: Deal better with neither design nor full capacity not being reported
ACPI / battery: Use design-cap for capacity calculations if full-cap is not available
ACPI / battery: Deal with design or full capacity being reported as -1
* acpi-video:
ACPI: video: Do not export a non working backlight interface on MSI MS-7721 boards
ACPI: video: Use native backlight on Lenovo E41-25/45
ACPI: video: fix typo in comment
* acpi-fan:
ACPI: fan: Expose fan performance state information
* acpi-drivers:
thermal: int340x_thermal: Add Tiger Lake ACPI device IDs
platform/x86: intel-hid: Add Tiger Lake ACPI device ID
ACPI: fan: Add Tiger Lake ACPI device ID
ACPI: DPTF: Add Tiger Lake ACPI device IDs
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200104152107.11407-7-krzk@kernel.org
Since commit d36e2fa025 ("thermal: generic-adc: make lookup table
optional") "generic-adc-thermal" can be used with an IIO_TEMP channel.
In this case the following message is logged at probe time:
no lookup table, assuming DAC channel returns milliCelcius
Silence this info message if the channel type is known to be in
milli celsius. Keep this message when the channel type is unknown or not
of type temperature.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200107232044.889075-3-martin.blumenstingl@googlemail.com
A "generic-adc-thermal" without "temperature-lookup-table" is perfectly
valid since commit d36e2fa025 ("thermal: generic-adc: make lookup
table optional"). On deferred probe the message "no lookup table,
assuming DAC channel returns milliCelcius" is still logged.
Prevent this message on deferred probe of the IIO channel by first
looking up the IIO channel.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200107232044.889075-2-martin.blumenstingl@googlemail.com
This patch adds the support for allwinner thermal sensor, within
allwinner SoC. It will register sensors for thermal framework
and use device tree to bind cooling device.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219172823.1652600-2-anarsoul@gmail.com
The function of_thermal_destroy_zones() is only used internally by the
of_parse_thermal_zones() for rollbacking in case of error.
Make it static and tag it as an __init function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219222154.16100-1-daniel.lezcano@linaro.org
As we introduced the idle injection cooling device called
cpuidle_cooling, let's be consistent and rename the cpu_cooling to
cpufreq_cooling as this one mitigates with OPPs changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20191219225317.17158-3-daniel.lezcano@linaro.org
The cpu idle cooling device offers a new method to cool down a CPU by
injecting idle cycles at runtime.
It has some similarities with the intel power clamp driver but it is
actually designed to be more generic and relying on the idle injection
powercap framework.
The idle injection duration is fixed while the running duration is
variable. That allows to have control on the device reactivity for the
user experience.
An idle state powering down the CPU or the cluster will allow to drop
the static leakage, thus restoring the heat capacity of the SoC. It
can be set with a trip point between the hot and the critical points,
giving the opportunity to prevent a hard reset of the system when the
cpufreq cooling fails to cool down the CPU.
With more sophisticated boards having a per core sensor, the idle
cooling device allows to cool down a single core without throttling
the compute capacity of several cpus belonging to the same clock line,
so it could be used in collaboration with the cpufreq cooling device.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20191219225317.17158-2-daniel.lezcano@linaro.org
By default, of-based thermal drivers do not enable hwmon.
Explicitly enable hwmon for both, the soc and gpu temperature
sensor.
Signed-off-by: Stefan Schaeckeler <schaecsn@gmx.net>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191212061702.BFE2D6E85603@corona.crabdance.com
The next changes will add a new way to cool down a CPU by injecting
idle cycles. With the current configuration, a CPU cooling device is
the cpufreq cooling device. As we want to add a new CPU cooling
device, let's convert the CPU cooling to a choice giving a list of CPU
cooling devices. At this point, there is obviously only one CPU
cooling device.
There is no functional changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20191204153930.9128-1-daniel.lezcano@linaro.org
Expose thermal readings as a HWMON device, so that it could be
accessed using lm-sensors.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-13-andrew.smirnov@gmail.com
Before returning measured temperature data to upper layer we need to
make sure that the reading was marked as "valid" to avoid reporting
bogus data.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-11-andrew.smirnov@gmail.com
Tmu_get_temp will get called as a part of sensor registration via
devm_thermal_zone_of_sensor_register(). To prevent it from retruning
bogus data we need to enable sensor monitoring before that. Looking at
the datasheet (i.MX8MQ RM) there doesn't seem to be any harm in
enabling them all, so, for the sake of simplicity, change the code to
do just that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-10-andrew.smirnov@gmail.com
Convert driver to use regmap API, drop custom LE/BE IO helpers and
simplify bit manipulation using regmap_update_bits(). This also allows
us to convert some register initialization to use loops and adds
convenient debug access to TMU registers via debugfs.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-9-andrew.smirnov@gmail.com
Driver data of underlying struct device will be set to NULL by Linux's
driver infrastructure. Clearing it here is unnecessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-8-andrew.smirnov@gmail.com
We can simplify error cleanup code if instead of passing a "struct
platform_device *" to qoriq_tmu_calibration() and deriving a bunch of
pointers from it, we pass those pointers directly. This way we won't
be force to call platform_set_drvdata() as early in qoriq_tmu_probe()
and need to have "platform_set_drvdata(pdev, NULL);" in error path.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-7-andrew.smirnov@gmail.com
Pass all necessary data to qoriq_tmu_register_tmu_zone() directly
instead of passing a platform device and then deriving it. This is
done as a first step to simplify resource deallocation code.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-6-andrew.smirnov@gmail.com
Embed per-sensor data into struct qoriq_tmu_data so we can drop the
code allocating it. This also allows us to get rid of per-sensor back
reference to struct qoriq_tmu_data since now its address can be
calculated using container_of().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-5-andrew.smirnov@gmail.com
Struct thermal_zone_device reference stored as sensor's private data
isn't really used anywhere in the code. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: linux-imx@nxp.com
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191210164153.10463-3-andrew.smirnov@gmail.com
Fix up the following warning when compiled with make W=1:
linux.git/drivers/thermal/zx2967_thermal.c:57: warning: Function
parameter or member 'dev' not described in 'zx2967_thermal_priv'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1b4f6fb91e2e713ad5135f0d40dcded65dee9d0e.1574242756.git.amit.kucheria@linaro.org
Fix up the following warning when compiled with make W=1:
linux.git/drivers/thermal/amlogic_thermal.c:78: warning: Function parameter or member 'A' not described in 'amlogic_thermal_soc_calib_data'
linux.git/drivers/thermal/amlogic_thermal.c:78: warning: Function parameter or member 'B' not described in 'amlogic_thermal_soc_calib_data'
linux.git/drivers/thermal/amlogic_thermal.c:78: warning: Function parameter or member 'm' not described in 'amlogic_thermal_soc_calib_data'
linux.git/drivers/thermal/amlogic_thermal.c:78: warning: Function parameter or member 'n' not described in 'amlogic_thermal_soc_calib_data'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/139c9191f1a18d528b5f94376facf40291d28244.1574242756.git.amit.kucheria@linaro.org
Fix up the following warning when compiled with make W=1:
linux.git/drivers/thermal/tegra/soctherm.c:369: warning: Function parameter or member 'value' not described in 'ccroc_writel'
linux.git/drivers/thermal/tegra/soctherm.c:369: warning: Excess function parameter 'v' description in 'ccroc_writel'
linux.git/drivers/thermal/tegra/soctherm.c:447: warning: Function parameter or member 'dev' not described in 'enforce_temp_range'
linux.git/drivers/thermal/tegra/soctherm.c:772: warning: Function parameter or member 'sg' not described in 'tegra_soctherm_set_hwtrips'
linux.git/drivers/thermal/tegra/soctherm.c:772: warning: Function parameter or member 'tz' not described in 'tegra_soctherm_set_hwtrips'
linux.git/drivers/thermal/tegra/soctherm.c:944: warning: Function parameter or member 'ts' not described in 'soctherm_oc_intr_enable'
linux.git/drivers/thermal/tegra/soctherm.c:1167: warning: Function parameter or member 'data' not described in 'soctherm_oc_irq_disable'
linux.git/drivers/thermal/tegra/soctherm.c:1167: warning: Excess function parameter 'irq_data' description in 'soctherm_oc_irq_disable'
linux.git/drivers/thermal/tegra/soctherm.c:1224: warning: Function parameter or member 'ctrlr' not described in 'soctherm_irq_domain_xlate_twocell'
linux.git/drivers/thermal/tegra/soctherm.c:1686: warning: Function parameter or member 'pdev' not described in 'soctherm_init_hw_throt_cdev'
linux.git/drivers/thermal/tegra/soctherm.c:1764: warning: Function parameter or member 'ts' not described in 'throttlectl_cpu_level_cfg'
linux.git/drivers/thermal/tegra/soctherm.c:1812: warning: Function parameter or member 'ts' not described in 'throttlectl_cpu_level_select'
linux.git/drivers/thermal/tegra/soctherm.c:1855: warning: Function parameter or member 'ts' not described in 'throttlectl_cpu_mn'
linux.git/drivers/thermal/tegra/soctherm.c:1886: warning: Function parameter or member 'ts' not described in 'throttlectl_gpu_level_select'
linux.git/drivers/thermal/tegra/soctherm.c:1928: warning: Function parameter or member 'ts' not described in 'soctherm_throttle_program'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/db764f71253bb2ad569b0aeab4c91207a39317ce.1574242756.git.amit.kucheria@linaro.org
Fix up the following warning when compiled with make W=1:
linux.git/drivers/thermal/samsung/exynos_tmu.c:141: warning: bad
line: driver
linux.git/drivers/thermal/samsung/exynos_tmu.c:203: warning: Function
parameter or member 'tzd' not described in 'exynos_tmu_data'
linux.git/drivers/thermal/samsung/exynos_tmu.c:203: warning: Function
parameter or member 'tmu_set_trip_temp' not described in
'exynos_tmu_data'
linux.git/drivers/thermal/samsung/exynos_tmu.c:203: warning: Function
parameter or member 'tmu_set_trip_hyst' not described in
'exynos_tmu_data'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1ded1697c6e5eff11b034b3302b9c79e88fa9c42.1574242756.git.amit.kucheria@linaro.org
Replace a comment starting with /** by simply /* to avoid having it
interpreted as a kernel-doc comment. Describe missing function
parameters where needed.
Fixes up the following warnings when compiled with make W=1:
linux.git/drivers/thermal/rockchip_thermal.c:27: warning: cannot
understand function prototype: 'enum tshut_mode '
linux.git/drivers/thermal/rockchip_thermal.c:37: warning: cannot
understand function prototype: 'enum tshut_polarity '
linux.git/drivers/thermal/rockchip_thermal.c:46: warning: cannot
understand function prototype: 'enum sensor_id '
linux.git/drivers/thermal/rockchip_thermal.c:56: warning: cannot
understand function prototype: 'enum adc_sort_mode '
linux.git/drivers/thermal/rockchip_thermal.c:123: warning: Function
parameter or member 'chn_id' not described in 'rockchip_tsadc_chip'
linux.git/drivers/thermal/rockchip_thermal.c:123: warning: Function
parameter or member 'control' not described in 'rockchip_tsadc_chip'
linux.git/drivers/thermal/rockchip_thermal.c:167: warning: Function
parameter or member 'sensors' not described in 'rockchip_thermal_data'
linux.git/drivers/thermal/rockchip_thermal.c:608: warning: Function
parameter or member 'grf' not described in 'rk_tsadcv2_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:608: warning: Function
parameter or member 'regs' not described in 'rk_tsadcv2_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:608: warning: Function
parameter or member 'tshut_polarity' not described in
'rk_tsadcv2_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:644: warning: Function
parameter or member 'grf' not described in 'rk_tsadcv3_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:644: warning: Function
parameter or member 'regs' not described in 'rk_tsadcv3_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:644: warning: Function
parameter or member 'tshut_polarity' not described in
'rk_tsadcv3_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:732: warning: Function
parameter or member 'regs' not described in 'rk_tsadcv3_control'
linux.git/drivers/thermal/rockchip_thermal.c:732: warning: Function
parameter or member 'enable' not described in 'rk_tsadcv3_control'
linux.git/drivers/thermal/rockchip_thermal.c:1211: warning: Function
parameter or member 'reset' not described in
'rockchip_thermal_reset_controller'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/c3cbdb0619fec602668ba7ae703ba49d67e30b33.1574242756.git.amit.kucheria@linaro.org
Replace a comment starting with /** by simply /* to avoid having it
interpreted as a kernel-doc comment. Describe missing function
parameters where needed.
Fixes up the following warnings when compiled with make W=1:
linux.git/drivers/thermal/mtk_thermal.c:374: warning: cannot understand
function prototype: 'const struct mtk_thermal_data mt8173_thermal_data =
'
linux.git/drivers/thermal/mtk_thermal.c:413: warning: cannot understand
function prototype: 'const struct mtk_thermal_data mt2701_thermal_data =
'
linux.git/drivers/thermal/mtk_thermal.c:443: warning: cannot understand
function prototype: 'const struct mtk_thermal_data mt2712_thermal_data =
'
linux.git/drivers/thermal/mtk_thermal.c:499: warning: cannot understand
function prototype: 'const struct mtk_thermal_data mt8183_thermal_data =
'
linux.git/drivers/thermal/mtk_thermal.c:529: warning: Function parameter
or member 'sensno' not described in 'raw_to_mcelsius'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/ba10b886705879fd1b7d529fec50503d6696df20.1574242756.git.amit.kucheria@linaro.org
Fix up the following warning when compiled with make W=1:
linux.git/drivers/thermal/max77620_thermal.c:48: warning: Function
parameter or member 'temp' not described in 'max77620_thermal_read_temp'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/c943d51e7913a4b73cda447547b8ee77c857f7ba.1574242756.git.amit.kucheria@linaro.org
Fix up the following warnings with make W=1:
linux.git/drivers/thermal/devfreq_cooling.c:68: warning: Function
parameter or member 'capped_state' not described in
'devfreq_cooling_device'
linux.git/drivers/thermal/devfreq_cooling.c:593: warning: Function
parameter or member 'cdev' not described in 'devfreq_cooling_unregister'
linux.git/drivers/thermal/devfreq_cooling.c:593: warning: Excess
function parameter 'dfc' description in 'devfreq_cooling_unregister'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/7059d82472fe12139fc7a3379c5b9716a23cce5c.1574242756.git.amit.kucheria@linaro.org
Replace - with : to appease the kernel-doc gods and fix warnings such as
the following when compiled with make W=1:
linux-amit.git/drivers/thermal/step_wise.c:187: warning: Function
parameter or member 'tz' not described in 'step_wise_throttle'
linux-amit.git/drivers/thermal/step_wise.c:187: warning: Function
parameter or member 'trip' not described in 'step_wise_throttle'
linux.git/drivers/thermal/fair_share.c:79: warning: Function parameter
or member 'tz' not described in 'fair_share_throttle'
linux.git/drivers/thermal/fair_share.c:79: warning: Function parameter
or member 'trip' not described in 'fair_share_throttle'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/5d48ac6f85667a53902092ad5bbfef8cc89a7162.1574242756.git.amit.kucheria@linaro.org
Describe the function parameter to fix the following warning with make
W=1:
linux.git/drivers/thermal/cpu_cooling.c:92: warning: Function parameter
or member 'qos_req' not described in 'cpufreq_cooling_device'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/ddb09e9728533c274edae7ff3da515b3cf7ef231.1574242756.git.amit.kucheria@linaro.org
Replace a comment starting with /** by simply /* to avoid having
it interpreted as a kernel-doc comment.
Fixes the following warning when compile with make W=1:
linux.git/drivers/thermal/of-thermal.c:761: warning: cannot understand function prototype: 'const char *trip_types[] = '
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/dc742789bf4b3c8207b01c7946f2b401350536a7.1574242756.git.amit.kucheria@linaro.org
We are not interested in getting this debug print on our
console all the time.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Fixes: 6c375eccde ("thermal: db8500: Rewrite to be a pure OF sensor")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191119074650.2664-1-linus.walleij@linaro.org
In order for the old DTBs to continue working, the new interrupt code
must not return an error if interrupts are not defined. Don't return an
error in case of -ENXIO.
Fixes: 634e11d5b4 ("drivers: thermal: tsens: Add interrupt support")
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/cea3317c5d793db312064d68b261ad420a4a81b1.1576146898.git.amit.kucheria@linaro.org
Tiger Lake has new unique ACPI device IDs for thermal devices that
need to be added to the Intel thermal driver to suport it.
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When do randbuiding, we got this:
WARNING: unmet direct dependencies detected for THERMAL_GOV_POWER_ALLOCATOR
Depends on [n]: THERMAL [=y] && ENERGY_MODEL [=n]
Selected by [y]:
- THERMAL_DEFAULT_GOV_POWER_ALLOCATOR [=y] && <choice>
The Kconfig option THERMAL_DEFAULT_GOV_POWER_ALLOCATOR selects the
THERMAL_GOV_POWER_ALLOCATOR but this one depends on the ENERGY_MODEL
which is not enabled.
Make THERMAL_DEFAULT_GOV_POWER_ALLOCATOR depend on THERMAL_GOV_POWER_ALLOCATOR
to fix this warning.
Suggested-by: Quentin Perret <qperret@google.com>
Fixes: a4e893e802 ("thermal: cpu_cooling: Migrate to using the EM framework")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20191113105313.41616-1-yuehaibing@huawei.com
Pull thermal management updates from Zhang Rui:
- Fix a deadlock regression in thermal core framework, which was
introduced in 5.3 (Wei Wang)
- Initialize thermal control framework earlier to enable thermal
mitigation during boot (Amit Kucheria)
- Convert the Intelligent Power Allocator (IPA) thermal governor to
follow the generic PM_EM instead of its own Energy Model (Quentin
Perret)
- Introduce a new Amlogic soc thermal driver (Guillaume La Roque)
- Add interrupt support for tsens thermal driver (Amit Kucheria)
- Add support for MSM8956/8976 in tsens thermal driver
(AngeloGioacchino Del Regno)
- Add support for r8a774b1 in rcar thermal driver (Biju Das)
- Add support for Thermal Monitor Unit v2 in qoriq thermal driver
(Yuantian Tang)
- Some other fixes/cleanups on thermal core framework and soc thermal
drivers (Colin Ian King, Daniel Lezcano, Hsin-Yi Wang, Tian Tao)
* 'thermal/next' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (32 commits)
thermal: Fix deadlock in thermal thermal_zone_device_check
thermal: cpu_cooling: Migrate to using the EM framework
thermal: cpu_cooling: Make the power-related code depend on IPA
PM / EM: Declare EM data types unconditionally
arm64: defconfig: Enable CONFIG_ENERGY_MODEL
drivers: thermal: tsens: fix potential integer overflow on multiply
thermal: cpu_cooling: Reorder the header file
thermal: cpu_cooling: Remove pointless dependency on CONFIG_OF
thermal: no need to set .owner when using module_platform_driver
thermal: qcom: tsens-v1: Fix kfree of a non-pointer value
cpufreq: qcom-hw: Move driver initialization earlier
clk: qcom: Initialize clock drivers earlier
cpufreq: Initialize cpufreq-dt driver earlier
cpufreq: Initialize the governors in core_initcall
thermal: Initialize thermal subsystem earlier
thermal: Remove netlink support
dt: thermal: tsens: Document compatible for MSM8976/56
thermal: qcom: tsens-v1: Add support for MSM8956 and MSM8976
MAINTAINERS: add entry for Amlogic Thermal driver
thermal: amlogic: Add thermal driver to support G12 SoCs
...
* New bootctl driver for Mellanox BlueField SoC.
* New driver to support System76 laptops.
* Temperature monitoring and fan control on Acer Aspire 7551
is now supported.
* Previously the Huawei driver handled only hotkeys.
After the conversion to WMI it has been expanded
to support newer laptop models.
* Big refactoring of intel-speed-select tools allows to
use it on Intel CascadeLake-N systems.
* Touchscreen support for ezpad 6 m4 and
Schneider SCT101CTM tablets
* Miscellaneous clean ups and fixes here and there.
The following is an automated git shortlog grouped by driver:
acerhdf:
- Add support for Acer Aspire 7551
- Rename Peter Feuerer to Peter Kaestle
Add System76 ACPI driver:
- Add System76 ACPI driver
asus-laptop:
- switch to using polled mode of input devices
classmate-laptop:
- remove unused variable
dell-laptop:
- disable kbd backlight on Inspiron 10xx
hdaps:
- switch to using polled mode of input devices
hp-wmi:
- Fix ACPI errors caused by passing 0 as input size
- Fix ACPI errors caused by too small buffer
huawei-wmi:
- Remove unnecessary battery mutex
- No need to check for battery name
- Stricter battery thresholds set
- Fix a precision vs width printf bug
- Avoid use of global variable when possible
- No need to keep pointer to platform device
- Don't leak memory on the exit
- huawei_wmi can be static
- Add debugfs support
- Add fn-lock support
- Add battery charging thresholds
- Implement huawei wmi management
- Add quirks and module parameters
- Move to platform driver
i2c-multi-instantiate:
- Fail the probe if no IRQ provided
intel_cht_int33fe:
- Split code to Micro-B and Type-C
intel_int0002_vgpio:
- Pass irqchip when adding gpiochip
intel_pmc_core:
- Add Comet Lake (CML) platform support to intel_pmc_core driver
- Fix the SoC naming inconsistency
intel_punit_ipc:
- Drop useless label
- use devm_platform_ioremap_resource() to simplify code
- Avoid error message when retrieving IRQ
peaq-wmi:
- switch to using polled mode of input devices
platform/mellanox:
- Fix Kconfig indentation
- Add bootctl driver for Mellanox BlueField Soc
tools/power/x86/intel-speed-select:
- Display TRL buckets for just base config level
- Ignore missing config level
- Increment version
- Use core count for base-freq mask
- Support platform with limited Intel(R) Speed Select
- Use Frequency weight for CLOS
- Make CLOS frequency in MHz
- Use mailbox for CLOS_PM_QOS_CONFIG
- Auto mode for CLX
- Correct CLX-N frequency units
- Change display of "avx" to "avx2"
- Extend command set for perf-profile
- Implement base-freq commands on CascadeLake-N
- Implement 'perf-profile info' on CascadeLake-N
- Implement CascadeLake-N help and command functions structures
- Add check for CascadeLake-N models
- Make process_command generic
- Add int argument to command functions
- Refuse to disable core-power when getting used
- Turbo-freq feature auto mode
- Base-freq feature auto mode
- Remove warning for unused result
toshiba_acpi:
- do not select INPUT_POLLDEV
touchscreen_dmi:
- Add info for the ezpad 6 m4 tablet
- Add touchscreen platform data for the Schneider SCT101CTM tablet
-----BEGIN PGP SIGNATURE-----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=KkPQ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.5-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- New bootctl driver for Mellanox BlueField SoC.
- New driver to support System76 laptops.
- Temperature monitoring and fan control on Acer Aspire 7551 is now
supported.
- Previously the Huawei driver handled only hotkeys. After the
conversion to WMI it has been expanded to support newer laptop
models.
- Big refactoring of intel-speed-select tools allows to use it on Intel
CascadeLake-N systems.
- Touchscreen support for ezpad 6 m4 and Schneider SCT101CTM tablets
- Miscellaneous clean ups and fixes here and there.
* tag 'platform-drivers-x86-v5.5-1' of git://git.infradead.org/linux-platform-drivers-x86: (59 commits)
platform/x86: hp-wmi: Fix ACPI errors caused by passing 0 as input size
platform/x86: hp-wmi: Fix ACPI errors caused by too small buffer
platform/x86: intel_pmc_core: Add Comet Lake (CML) platform support to intel_pmc_core driver
platform/x86: intel_pmc_core: Fix the SoC naming inconsistency
platform/mellanox: Fix Kconfig indentation
tools/power/x86/intel-speed-select: Display TRL buckets for just base config level
tools/power/x86/intel-speed-select: Ignore missing config level
platform/x86: touchscreen_dmi: Add info for the ezpad 6 m4 tablet
tools/power/x86/intel-speed-select: Increment version
tools/power/x86/intel-speed-select: Use core count for base-freq mask
tools/power/x86/intel-speed-select: Support platform with limited Intel(R) Speed Select
tools/power/x86/intel-speed-select: Use Frequency weight for CLOS
tools/power/x86/intel-speed-select: Make CLOS frequency in MHz
tools/power/x86/intel-speed-select: Use mailbox for CLOS_PM_QOS_CONFIG
tools/power/x86/intel-speed-select: Auto mode for CLX
tools/power/x86/intel-speed-select: Correct CLX-N frequency units
tools/power/x86/intel-speed-select: Change display of "avx" to "avx2"
tools/power/x86/intel-speed-select: Extend command set for perf-profile
Add touchscreen platform data for the Schneider SCT101CTM tablet
platform/x86: intel_int0002_vgpio: Pass irqchip when adding gpiochip
...
The newly introduced Energy Model framework manages power cost tables in
a generic way. Moreover, it supports several types of models since the
tables can come from DT or firmware (through SCMI) for example. On the
other hand, the cpu_cooling subsystem manages its own power cost tables
using only DT data.
In order to avoid the duplication of data in the kernel, and in order to
enable IPA with EMs coming from more than just DT, remove the private
tables from cpu_cooling.c and migrate it to using the centralized EM
framework. Doing so should have no visible functional impact for
existing users of IPA since:
- recent extenstions to the the PM_OPP infrastructure enable the
registration of EMs in PM_EM using the DT property used by IPA;
- the existing upstream cpufreq drivers marked with the
'CPUFREQ_IS_COOLING_DEV' flag all use the aforementioned PM_OPP
infrastructure, which means they all support PM_EM. The only two
exceptions are qoriq-cpufreq which doesn't in fact use an EM and
scmi-cpufreq which doesn't use DT for power costs.
For existing users of cpu_cooling, PM_EM tables will contain the exact
same power values that IPA used to compute on its own until now. The
only new dependency for them is to compile in CONFIG_ENERGY_MODEL.
The case where the thermal subsystem is used without an Energy Model
(cpufreq_cooling_ops) is handled by looking directly at CPUFreq's
frequency table which is already a dependency for cpu_cooling.c anyway.
Since the thermal framework expects the cooling states in a particular
order, bail out whenever the CPUFreq table is unsorted, since that is
fairly uncommon in general, and there are currently no users of
cpu_cooling for this use-case.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191030151451.7961-5-qperret@google.com
The core CPU cooling infrastructure has power-related functions
that have only one client: IPA. Since there can be no user of those
functions if IPA is not compiled in, make sure to guard them with
checks on CONFIG_THERMAL_GOV_POWER_ALLOCATOR to not waste space
unnecessarily.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191030151451.7961-4-qperret@google.com
Currently a multiply operation is being performed on two int values
and the result is being assigned to a u64, presumably because the
end result is expected to be probably larger than an int. However,
because the multiply is an int multiply one can get overflow. Avoid
the overflow by casting degc to a u64 to force a u64 multiply.
Also use div_u64 for the divide as suggested by Daniel Lezcano.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: fbfe1a042cfd ("drivers: thermal: tsens: Add interrupt support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20191101100035.25502-1-colin.king@canonical.com
the module_platform_driver will call platform_driver_register.
and It will set the .owner to THIS_MODULE
Signed-off-by: Tian Tao <tiantao6@huawei.com>
Acked-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1572051875-35861-1-git-send-email-tiantao6@huawei.com
Currently the kfree of pointer qfprom_cdata is kfreeing an
error value that has been cast to a pointer rather than a
valid address. Fix this by removing the kfree.
Fixes: 95ededc17e4e ("thermal: qcom: tsens-v1: Add support for MSM8956 and MSM8976")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191022111806.23143-1-colin.king@canonical.com
Now that the thermal framework is built-in, in order to facilitate
thermal mitigation as early as possible in the boot cycle, move the
thermal framework initialization to core_initcall.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/f8ff0ab4a8e9c2eca5a26fb2256365b26cb326ce.1571656015.git.amit.kucheria@linaro.org
Add support for reading calibrated value from thermistors in
MSM8956, MSM8976 and their APQ variants.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191005104133.30297-2-kholk11@gmail.com
Amlogic G12A and G12B SoCs integrate two thermal sensors
with the same design. One is located close to the DDR controller
and the other one is located close to the PLLs (between the CPU and GPU).
The calibration data for each of the thermal sensors instance is stored
in a different location within the AO region.
Implement reading the temperature from each thermal sensor.
The IP block has more functionality, which may be added to this driver
in the future:
- chip reset when the temperature exceeds a configurable threshold
- up to four interrupts when the temperature has risen above a
configurable threshold
- up to four interrupts when the temperature has fallen below a
configurable threshold
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191004090114.30694-3-glaroque@baylibre.com
Depending on the IP version, TSENS supports upper, lower and critical
threshold interrupts. We only add support for upper and lower threshold
interrupts for now.
TSENSv2 has an irq [status|clear|mask] bit tuple for each sensor while
earlier versions only have a single bit per sensor to denote status and
clear. These differences are handled transparently by the interrupt
handler. At each interrupt, we reprogram the new upper and lower threshold
in the .set_trip callback.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/7508ba143f144407e5dd546107ddae65c380a76f.1572526427.git.amit.kucheria@linaro.org
Move platform_set_drvdata up to avoid an extra 'if (ret)' check after
the call to tsens_register.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/184422dcc1c12553e71a58c62e01425fd7d1172a.1572526427.git.amit.kucheria@linaro.org
There are two fields - id and hw_id - to track what sensor an action was
to performed on. This was because the sensors connected to a TSENS IP
might not be contiguous i.e. 1, 2, 4, 5 with 3 being skipped.
This causes confusion in the code which uses hw_id sometimes and id
other times (tsens_get_temp, tsens_get_trend).
Switch to only using the hw_id field to track the physical ID of the
sensor. When we iterate through all the sensors connected to an IP
block, we use an index i to loop through the list of sensors, and then
return the actual hw_id that is registered on that index.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/30206cd47d303d2dcaef87f4e3c7173481a0bddd.1572526427.git.amit.kucheria@linaro.org
Thermal Monitor Unit v2 is introduced on new Layscape SoC.
Compared to v1, TMUv2 has a little different register layout
and digital output is fairly linear.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191011020534.334-1-andy.tang@nxp.com
If devm_iio_channel_get() or devm_thermal_zone_of_sensor_register()
fail with EPROBE_DEFER, we shouldn't print an error message, as the
device will be probed again later.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20190910075907.132200-1-hsinyi@chromium.org
Rename Peter Feuerer to Peter Kaestle.
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Kaestle <peter@piie.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Replace the CPU device PM QoS used for the management of min and max
frequency constraints in cpufreq (and its users) with per-policy
frequency QoS to avoid problems with cpufreq policies covering
more then one CPU.
Namely, a cpufreq driver is registered with the subsys interface
which calls cpufreq_add_dev() for each CPU, starting from CPU0, so
currently the PM QoS notifiers are added to the first CPU in the
policy (i.e. CPU0 in the majority of cases).
In turn, when the cpufreq driver is unregistered, the subsys interface
doing that calls cpufreq_remove_dev() for each CPU, starting from CPU0,
and the PM QoS notifiers are only removed when cpufreq_remove_dev() is
called for the last CPU in the policy, say CPUx, which as a rule is
not CPU0 if the policy covers more than one CPU. Then, the PM QoS
notifiers cannot be removed, because CPUx does not have them, and
they are still there in the device PM QoS notifiers list of CPU0,
which prevents new PM QoS notifiers from being registered for CPU0
on the next attempt to register the cpufreq driver.
The same issue occurs when the first CPU in the policy goes offline
before unregistering the driver.
After this change it does not matter which CPU is the policy CPU at
the driver registration time and whether or not it is online all the
time, because the frequency QoS is per policy and not per CPU.
Fixes: 67d874c3b2 ("cpufreq: Register notifiers with the PM QoS framework")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Diagnosed-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/linux-pm/5ad2624194baa2f53acc1f1e627eb7684c577a19.1562210705.git.viresh.kumar@linaro.org/T/#md2d89e95906b8c91c15f582146173dce2e86e99f
Link: https://lore.kernel.org/linux-pm/20191017094612.6tbkwoq4harsjcqv@vireshk-i7/T/#m30d48cc23b9a80467fbaa16e30f90b3828a5a29b
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull thermal SoC updates from Eduardo Valentin:
"This is a really small pull in the midst of a lot of pending patches.
We are in the middle of restructuring how we are maintaining the
thermal subsystem, as per discussion in our last LPC. For now, I am
sending just some changes that were pending in my tree. Looking
forward to get a more streamlined process in the next merge window"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: db8500: Rewrite to be a pure OF sensor
thermal: db8500: Use dev helper variable
thermal: db8500: Finalize device tree conversion
thermal: thermal_mmio: remove some dead code
Pull thermal management updates from Zhang Rui:
- Add Amit Kucheria as thermal subsystem Reviewer (Amit Kucheria)
- Fix a use after free bug when unregistering thermal zone devices (Ido
Schimmel)
- Fix thermal core framework to use put_device() when device_register()
fails (Yue Hu)
- Enable intel_pch_thermal and MMIO RAPL support for Intel Icelake
platform (Srinivas Pandruvada)
- Add clock operations in qorip thermal driver, for some platforms with
clock control like i.MX8MQ (Anson Huang)
- A couple of trivial fixes and cleanups for thermal core and different
soc thermal drivers (Amit Kucheria, Christophe JAILLET, Chuhong Yuan,
Fuqian Huang, Kelsey Skunberg, Nathan Huckleberry, Rishi Gupta,
Srinivas Kandagatla)
* 'for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
MAINTAINERS: Add Amit Kucheria as reviewer for thermal
thermal: Add some error messages
thermal: Fix use-after-free when unregistering thermal zone device
thermal/drivers/core: Use put_device() if device_register() fails
thermal_hwmon: Sanitize thermal_zone type
thermal: intel: Use dev_get_drvdata
thermal: intel: int3403: replace printk(KERN_WARN...) with pr_warn(...)
thermal: intel: int340x_thermal: Remove unnecessary acpi_has_method() uses
thermal: int340x: processor_thermal: Add Ice Lake support
drivers: thermal: qcom: tsens: Fix memory leak from qfprom read
thermal: tegra: Fix a typo
thermal: rcar_gen3_thermal: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
thermal: armada: Fix -Wshift-negative-value
dt-bindings: thermal: qoriq: Add optional clocks property
thermal: qoriq: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
thermal: qoriq: Use devm_platform_ioremap_resource() instead of of_iomap()
thermal: qoriq: Fix error path of calling qoriq_tmu_register_tmu_zone fail
thermal: qoriq: Add clock operations
drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset
This patch rewrites the DB8500 thermal sensor to be a
pure OF sensor, so that it can be used with thermal zones
defined in the device tree.
This driver was initially merged before we had generic
thermal zone device tree bindings, and now it gets
modernized to the way we do things these days.
The old driver depended on a set of trigger points
provided in the device tree or platform data to
interpolate the current temperature between trigger
points depending on whether the trend was rising or
falling. This was bad because the trigger points should
be used for defining temperature zone policies and
bind to cooling devices.
As the PRCMU (power reset control management unit) can
only issue IRQs when we pass temperature trigger points
upward or downward We instead define a number of
temperature points inside the driver ranging from
15 to 100 degrees celsius. The effect is that when
we register the device we quickly trigger 15, 20 ... up
to the room temperature in succession and then we
get continous event IRQs also under normal operating
conditions, and the temperature of the system is now
reported more accurately (+/- 2.5 degrees celsius)
while in the past the first trigger point was at 70
degrees and the average temperature was simply reported
as 35 degrees celsius (between 70 degrees and 0) until
we passed 70 degrees which didn't accurately represent
the temperature of the system.
As a result of dropping all the trigger points from the
driver and reusing the core DT thermal zone management
code we reduce the code footprint quite a bit.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The code gets easier to read like this.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
At some point there was an attempt to convert the DB8500
thermal sensor to device tree: a probe path was added
and the device tree was augmented for the Snowball board.
The switchover was never completed: instead the thermal
devices came from from the PRCMU MFD device and the probe
on the Snowball was confused as another set of configuration
appeared from the device tree.
Move over to a device-tree only approach, as we fixed up
the device trees.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When registering a thermal zone device, we currently return -EINVAL in
four cases. This makes it a little hard to debug the real cause of the
failure.
Print some error messages to make it easier for developer to figure out
what happened.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Never directly free @dev after calling device_register(), even if it
returned an error! Always use put_device() to give up the reference
initialized. Clean up the rollback block also.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When calling thermal_add_hwmon_sysfs(), the device type is sanitized by
replacing '-' with '_'. However tz->type remains unsanitized. Thus
calling thermal_hwmon_lookup_by_type() returns no device. And if there is
no device, thermal_remove_hwmon_sysfs() fails with "hwmon device lookup
failed!".
The result is unregisted hwmon devices in the sysfs.
Fixes: 409ef0baca ("thermal_hwmon: Sanitize attribute name passed to hwmon")
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Direct invocation of printk() is not preferred to emit logs.
This commit replaces printk(KERN_WARNING) with corresponding
pr_warn() function call.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
acpi_evaluate_object() will already return in error if the method does not
exist. Checking if the method is absent before the acpi_evaluate_object()
call is not needed. Remove acpi_has_method() calls to avoid additional
work.
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add new PCI id for Ice lake processor thermal device. Also enabled
the RAPL mmio interface. The MMIO offsets match Skylake.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The platform_get_resource() function doesn't return error pointers, it
returns NULL. The way this is normally done, is that we pass the NULL
resource to devm_ioremap_resource() and then check for errors from that.
See the comment in front of devm_ioremap_resource() for more details.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* pm-cpufreq: (36 commits)
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
sched/cpufreq: Align trace event behavior of fast switching
ACPI: cpufreq: Switch to QoS requests instead of cpufreq notifier
video: pxafb: Remove cpufreq policy notifier
video: sa1100fb: Remove cpufreq policy notifier
arch_topology: Use CPUFREQ_CREATE_POLICY instead of CPUFREQ_NOTIFY
cpufreq: powerpc_cbe: Switch to QoS requests for freq limits
cpufreq: powerpc: macintosh: Switch to QoS requests for freq limits
cpufreq: Print driver name if cpufreq_suspend() fails
cpufreq: mediatek: Add support for mt8183
cpufreq: mediatek: change to regulator_get_optional
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
cpufreq: Use imx-cpufreq-dt for i.MX8MN's speed grading
...
The play_idle resolution is 1ms. The intel_powerclamp bases the idle
duration on jiffies. The idle injection API is also using msec based
duration but has no user yet.
Unfortunately, msec based time does not fit well when we want to
inject idle cycle precisely with shallow idle state.
In order to set the scene for the incoming idle injection user, move
the precision up to usec when calling play_idle.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
memory returned as part of nvmem_read via qfprom_read should be
freed by the consumer once done.
Existing code is not doing it so fix it.
Below memory leak detected by kmemleak
[<ffffff80088b7658>] kmemleak_alloc+0x50/0x84
[<ffffff80081df120>] __kmalloc+0xe8/0x168
[<ffffff80086db350>] nvmem_cell_read+0x30/0x80
[<ffffff8008632790>] qfprom_read+0x4c/0x7c
[<ffffff80086335a4>] calibrate_v1+0x34/0x204
[<ffffff8008632518>] tsens_probe+0x164/0x258
[<ffffff80084e0a1c>] platform_drv_probe+0x80/0xa0
[<ffffff80084de4f4>] really_probe+0x208/0x248
[<ffffff80084de2c4>] driver_probe_device+0x98/0xc0
[<ffffff80084dec54>] __device_attach_driver+0x9c/0xac
[<ffffff80084dca74>] bus_for_each_drv+0x60/0x8c
[<ffffff80084de634>] __device_attach+0x8c/0x100
[<ffffff80084de6c8>] device_initial_probe+0x20/0x28
[<ffffff80084dcbb8>] bus_probe_device+0x34/0x7c
[<ffffff80084deb08>] deferred_probe_work_func+0x6c/0x98
[<ffffff80080c3da8>] process_one_work+0x160/0x2f8
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Clang produces the following warning
drivers/thermal/armada_thermal.c:270:33: warning: shifting a negative
signed value is undefined [-Wshift-negative-value]
1 warning reg &= ~CONTROL1_TSEN_AVG_MASK <<
CONTROL1_TSEN_AVG_SHIFT; generated
.
~~~~~~~~~~~~~~~~~~~~~~~ ^
CONTROL1_TSEN_AVG_SHIFT is defined to be zero.
Since shifting by zero does nothing this variable can be removed.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/532
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use __maybe_unused for power management related functions
instead of #if CONFIG_PM_SLEEP to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use devm_platform_ioremap_resource() instead of of_iomap() to
save the iounmap() call in error handle path;
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When registering tmu zone failed, the error path should be err_tmu
instead of err_iomap, as iounmap() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Some platforms like i.MX8MQ has clock control for this module,
need to add clock operations to make sure the driver is working
properly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This change exports an interface to read tcc offset and allow writing if
the platform is not locked.
Refer to Intel SDM for details on the MSR: MSR_TEMPERATURE_TARGET.
Here TCC Activation Offset (R/W) bits allow temperature offset in degrees
in relation to TjMAX.
This change will be useful for improving performance from user space for
some platforms, if the current offset is not optimal.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The cpufreq core now takes the min/max frequency constraints via QoS
requests and the CPUFREQ_ADJUST notifier shall get removed later on.
Switch over to using the QoS request for maximum frequency constraint
for cpu_cooling driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Passing 0 to cpuhp_remove_state() triggers the BUG_ON() in
__cpuhp_remove_state_cpuslocked() and the argument passed to
powercap_unregister_control_type() is expected to be a valid
pointer, so avoid calling these functions with incorrect
arguments from proc_thermal_rapl_remove().
Fixes: 555c45fe0d ("int340X/processor_thermal_device: add support for MMIO RAPL")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
- Add MMIO interface support to the Intel RAPL power capping
driver and update the int340X thermal driver to provide a
RAPL MMIO interface (Zhang Rui, Stephen Rothwell).
- Add Intel Ice Lake CPU IDs to the RAPL driver (Zhang Rui,
Rajneesh Bhardwaj).
- Make cpufreq use the PM QoS framework (instead of notifiers) for
managing the min and max frequency constraints (Viresh Kumar).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl0wLTgSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxpckP/2DmQ5ydn1EvY47mpMtdEcnptCaMUwoM
xL6oo3hcpZsmHL8uslESW/LCE+Zadq1oz0k8rCiMKIzbujTzaDD+Pbzd/8ueY8nK
YHyNMQaVS23iixix0/UqTsDd2zk2HNvaBGihHhnQAS0tXdJKgvWa7lgIpG2rBQL3
7P/aug1xum1r6DSbDA1+4dQ7XAZcLzK8mw25mdBRo+exBxGCJreOUu1K8DaQ4wrw
aw2DuvBUk4+wmE1acq693uLbDjGA26F6H2Ul/BpcvYK2Bdn+Ec8sOK1N/xkRxdbc
0IxozORawIG6SQRrP1+N+3Tmau79iOnSSAOAtum6XJ06bRvRXo48IrbtnTHuYCrO
gLLzG9DkjYeJx1ymcqQXscAhH4cwm2zEvBqCdy9RXXViZVHmWfN9LeGlYTc9lV33
+X9Co7XevOA3f4DRVhbDFJi/neVEu+RIeBfd7F0dnU0nY2pbtHrBducmTiQOQG2N
HiQ0HPTrMJI7qmr56AxnXQPqvlDP3ys/dygid/vIZL/7Pjqa2T6oWqixvQR+T5/X
wajJM5k8d+KVW0QuuKBGTzhRCjnD+fqGagn+X9kaF8F66i9tMeeSYhd7abIBxMQV
nU61DsOgLWmulrk3f1BSdKaig0U9QMxQLIZI15/CuLH8hv/ctuodCDJLxXykfxlG
CaJOoWC18kj2
=Svee
-----END PGP SIGNATURE-----
Merge tag 'pm-5.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These modify the Intel RAPL driver to allow it to use an MMIO
interface to the hardware, make the int340X thermal driver provide
such an interface for it, add Intel Ice Lake CPU IDs to the RAPL
driver (these changes depend on the previously merged x86 arch
changes), update cpufreq to use the PM QoS framework for managing the
min and max frequency limits, and add update the imx-cpufreq-dt
cpufreq driver to support i.MX8MN.
Specifics:
- Add MMIO interface support to the Intel RAPL power capping driver
and update the int340X thermal driver to provide a RAPL MMIO
interface (Zhang Rui, Stephen Rothwell).
- Add Intel Ice Lake CPU IDs to the RAPL driver (Zhang Rui, Rajneesh
Bhardwaj).
- Make cpufreq use the PM QoS framework (instead of notifiers) for
managing the min and max frequency constraints (Viresh Kumar).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang)"
* tag 'pm-5.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (27 commits)
cpufreq: Make cpufreq_generic_init() return void
intel_rapl: need linux/cpuhotplug.h for enum cpuhp_state
powercap/rapl: Add Ice Lake NNPI support to RAPL driver
powercap/intel_rapl: add support for ICX-D
powercap/intel_rapl: add support for ICX
powercap/intel_rapl: add support for IceLake desktop
intel_rapl: Fix module autoloading issue
int340X/processor_thermal_device: add support for MMIO RAPL
intel_rapl: support two power limits for every RAPL domain
intel_rapl: support 64 bit register
intel_rapl: abstract RAPL common code
intel_rapl: cleanup hardcoded MSR access
intel_rapl: cleanup some functions
intel_rapl: abstract register access operations
intel_rapl: abstract register address
intel_rapl: introduce struct rapl_if_private
intel_rapl: introduce intel_rapl.h
intel_rapl: remove hardcoded register index
intel_rapl: use reg instead of msr
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Introduce MMIO RAPL support as Intel processor_thermal device exposes the
capability to do RAPL control via MMIO registers.
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As a system sleep callback, proc_thermal_resume() should be defined only
if CONFIG_PM_SLEEP is defined.
This fixes a build warning when CONFIG_PM_SLEEP is not set,
drivers/thermal/intel/int340x_thermal/processor_thermal_device.c:446:12: error: 'proc_thermal_resume' defined but not used [-Werror=unused-function]
static int proc_thermal_resume(struct device *dev)
Fixes: aaba9791fb ("drivers: thermal: processor_thermal: Read PPCC on resume")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull x86 topology updates from Ingo Molnar:
"Implement multi-die topology support on Intel CPUs and expose the die
topology to user-space tooling, by Len Brown, Kan Liang and Zhang Rui.
These changes should have no effect on the kernel's existing
understanding of topologies, i.e. there should be no behavioral impact
on cache, NUMA, scheduler, perf and other topologies and overall
system performance"
* 'x86-topology-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/rapl: Cosmetic rename internal variables in response to multi-die/pkg support
perf/x86/intel/uncore: Cosmetic renames in response to multi-die/pkg support
hwmon/coretemp: Cosmetic: Rename internal variables to zones from packages
thermal/x86_pkg_temp_thermal: Cosmetic: Rename internal variables to zones from packages
perf/x86/intel/cstate: Support multi-die/package
perf/x86/intel/rapl: Support multi-die/package
perf/x86/intel/uncore: Support multi-die/package
topology: Create core_cpus and die_cpus sysfs attributes
topology: Create package_cpus sysfs attribute
hwmon/coretemp: Support multi-die/package
powercap/intel_rapl: Update RAPL domain name and debug messages
thermal/x86_pkg_temp_thermal: Support multi-die/package
powercap/intel_rapl: Support multi-die/package
powercap/intel_rapl: Simplify rapl_find_package()
x86/topology: Define topology_logical_die_id()
x86/topology: Define topology_die_id()
cpu/topology: Export die_id
x86/topology: Create topology_max_die_per_package()
x86/topology: Add CPUID.1F multi-die/package support
Now that the governor table is in place and the macro allows to browse the
table, declare the governor so the entry is added in the governor table
in the init section.
The [un]register_thermal_governors function does no longer need to use the
exported [un]register thermal governor's specific function which in turn
call the [un]register_thermal_governor. The governors are fully
self-encapsulated.
The cyclic dependency is no longer needed, remove it.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently the governors are declared in their respective files but they
export their [un]register functions which in turn call the [un]register
governors core's functions. That implies a cyclic dependency which is
not desirable. There is a way to self-encapsulate the governors by letting
them to declare themselves in a __init section table.
Define the table in the asm generic linker description like the other
tables and provide the specific macros to deal with.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Read PPCC power limits on system resume in case those limits changed
while system was suspended.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-pm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Wei Ni <wni@nvidia.com>
Cc: Yangtao Li <tiny.windzz@gmail.com>
Cc: linux-pm@vger.kernel.org
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 111 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.567572064@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
it and or modify it under the terms of the gnu general public
license version 2 as published by the free software foundation this
program is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 11 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.249870634@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 this program is distributed
in the hope that it will be useful but without any warranty without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 97 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.025053186@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull thermal SoC fix from Eduardo Valentin:
"A single revert, detected to cause issues on the tsens driver"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
Revert "drivers: thermal: tsens: Add new operation to check if a sensor is enabled"
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 83 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3e6a8fb330.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Amit Kucheria <amit.kucheria@linaro.org>
Reported-by: Andy Gross <andygro@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Update the formula to calculate temperature:
Currently, current TEMP is calculated as
average of val1 (is calculated by formula 1)
and val2 (is calculated by formula 2). But,
as description in HWM (chapter 10A.3.1.2 Normal Mode.)
If (TEMP_CODE < THCODE2[11:0]) CTEMP value should be val1.
If (TEMP_CODE > THCODE2[11:0]) CTEMP value should be val2.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Update the formula to calculate CTEMP:
Currently, the CTEMP is average of val1 (is calculated by
formula 1) and val2 (is calculated by formula 2). But,
as description in HWM (chapter 10A.3.1.1 Setting of Normal Mode)
If (STEMP < Tj_T) CTEMP value should be val1.
If (STEMP > Tj_T) CTEMP value should be val2.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pascal Paillet