Pull networking fixes from David Miller:
1) The value choosen for the new SO_MAX_PACING_RATE socket option on
parisc was very poorly choosen, let's fix it while we still can.
From Eric Dumazet.
2) Our generic reciprocal divide was found to handle some edge cases
incorrectly, part of this is encoded into the BPF as deep as the JIT
engines themselves. Just use a real divide throughout for now.
From Eric Dumazet.
3) Because the initial lookup is lockless, the TCP metrics engine can
end up creating two entries for the same lookup key. Fix this by
doing a second lookup under the lock before we actually create the
new entry. From Christoph Paasch.
4) Fix scatter-gather list init in usbnet driver, from Bjørn Mork.
5) Fix unintended 32-bit truncation in cxgb4 driver's bit shifting.
From Dan Carpenter.
6) Netlink socket dumping uses the wrong socket state for timewait
sockets. Fix from Neal Cardwell.
7) Fix netlink memory leak in ieee802154_add_iface(), from Christian
Engelmayer.
8) Multicast forwarding in ipv4 can overflow the per-rule reference
counts, causing all multicast traffic to cease. Fix from Hannes
Frederic Sowa.
9) via-rhine needs to stop all TX queues when it resets the device,
from Richard Weinberger.
10) Fix RDS per-cpu accesses broken by the this_cpu_* conversions. From
Gerald Schaefer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
s390/bpf,jit: fix 32 bit divisions, use unsigned divide instructions
parisc: fix SO_MAX_PACING_RATE typo
ipv6: simplify detection of first operational link-local address on interface
tcp: metrics: Avoid duplicate entries with the same destination-IP
net: rds: fix per-cpu helper usage
e1000e: Fix compilation warning when !CONFIG_PM_SLEEP
bpf: do not use reciprocal divide
be2net: add dma_mapping_error() check for dma_map_page()
bnx2x: Don't release PCI bars on shutdown
net,via-rhine: Fix tx_timeout handling
batman-adv: fix batman-adv header overhead calculation
qlge: Fix vlan netdev features.
net: avoid reference counter overflows on fib_rules in multicast forwarding
dm9601: add USB IDs for new dm96xx variants
MAINTAINERS: add virtio-dev ML for virtio
ieee802154: Fix memory leak in ieee802154_add_iface()
net: usbnet: fix SG initialisation
inet_diag: fix inet_diag_dump_icsk() to use correct state for timewait sockets
cxgb4: silence shift wrapping static checker warning
OMAP3 platforms support both DT and non-DT boot at the moment, make
the clock init work according to the used setup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
AM33xx clocks have now been moved to DT, thus remove the old data file
and use the new init code under OMAP clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Initializes clock data from device tree.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Initializes clock data from device tree.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP4 clocks have now been moved to DT, thus remove the old data file
and use the new init code under drivers/clk/omap/clk-44xx.c.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_init is now separated to a common function which gets called for all
SoC:s, which initializes the DT clocks and calls the SoC specific clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch provides top level functionality for the DT clock initialization.
Clock tree is initialized hierarchically starting from IP modules (CM/PRM/PRCM)
going down towards individual clock nodes, and finally initializing
clockdomains once all the clocks are ready.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DT clocks are mostly missing clkdm info now, and this causes an issue with
counter32k which makes its slave idlemode wrong and prevents core idle.
Fixed by initializing the hwmod clkdm pointers for omap3 also which makes
sure the clkdm flag matching logic works properly.
This patch also changes the return value for _init_clkdm to 0 for
incorrect clkdm_name, as this a warning, not a fatal error.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If the main clock for a hwmod is of basic clock type, it is illegal to type
cast this to clk_hw_omap and will result in bogus data. Fixed by checking
the clock flags before attempting the type cast.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Clock nodes shall use the services provided by underlying drivers to access
the hardware registers instead of direct memory read/write. Thus, change
all the code to use the new omap2_clk_readl / omap2_clk_writel APIs for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Using indexed memmaps is required for isolating the actual memory access
from the clock code. Now, the driver providing the support for the clock IP
block provides the low level routines for reading/writing clock registers
also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the AM43xx power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
AM35xx now uses the clock data from device tree. Most of the data is
shared with OMAP3xxx, but as there is some delta, a new base .dtsi
file is also created for the SoC.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the OMAP3 power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the AM33xx power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds optfclk_pciephy_clk and optfclk_pciephy_div_clk
which are used by PCIe phy. It also adds a mux clock to choose
the source of optfclk_pciephy_div_clk clock.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch changes apll_pcie_m2_ck to fixed factor
clock as there are no configurable divider associated to m2.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The patch adds a mux node to choose the parent of apll_pcie_ck node.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the DRA7 power,
reset and clock manager (PRCM).
TODO: apll_pcie clock node is still a dummy in this version, and
proper support for the APLL should be added.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the OMAP5 power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the OMAP4 power,
reset and clock manager (PRCM). OMAP443x and OMAP446x have slightly
different clock tree which is taken into account in the data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-3xxx.c now contains the clock init functionality for omap3, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP3 has interface clocks in addition to functional clocks, which
require special handling for the autoidle and idle status register
offsets mainly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-33xx.c now contains the clock init functionality for am33xx, including
DT clock registration and adding of static clkdev entries.
This patch also moves the omap2_clk_enable_init_clocks declaration to
the driver include, as this is needed by the am33xx clock init code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-54xx.c now contains the clock init functionality for omap5, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-44xx.c now contains the clock init functionality for omap4, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a multipurpose clock node, which contains support for multiple
sub-clocks. Uses basic composite clock type to implement the actual
functionality, and TI specific gate, mux and divider clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
TI clk driver now routes some of the basic clocks through own
registration routine to allow autoidle support. This routine just
checks a couple of device node properties and adds autoidle support
if required, and just passes the registration forward to basic clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
SOC_DRA7XX was under wrong menu within Kconfig file, which prevented
DRA7XX only build. Fixed the kconfig options for this SoC as we are
there. voltage.c needs to be added to the DRA7XX build also, otherwise
DRA7XX only build will fail.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DRA7XX and AM43XX were missing common clock code from the Makefile, which
causes build breakage in DRA7XX / AM43XX only builds once clock support
for these SoCs is added. Add the missing entries to the Makefile as
preparation of this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
* pm-cpufreq: (40 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
powernow-k6: reorder frequencies
powernow-k6: correctly initialize default parameters
powernow-k6: disable cache when changing frequency
Documentation: add ABI entry for intel_pstate
cpufreq: exynos: Convert exynos-cpufreq to platform driver
...
There are some parts of common kernel which would be using routines
like clk_get_rate() on some platforms. Currently, they wouldn't be
called for SA1100 boards, but they are needed for successful kernel
compilation.
Create a dummy clk_get_rate() routine for SA1100 which can be called
by the cpufreq core. More dummy routines might be added later if
necessary.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
platform device name from generic "watchdog"
to something more specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=C9qR
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/watchdog' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
This patch updates the davinci watchdog
platform device name from generic "watchdog"
to something more specific.
* tag 'davinci-for-v3.14/watchdog' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
watchdog: davinci: rename platform driver to davinci-wdt
Signed-off-by: Kevin Hilman <khilman@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=dQO3
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
A patch to fix the return value of clk_round_rate()
* tag 'davinci-for-v3.14/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: clock: return 0 upon error from clk_round_rate()
DT-enabled Marvell Kirkwood and Dove SoCs make use of an irqchip
driver. As expected for irqchip drivers, it uses a C-style
interrupt handler and therefore selects MULTI_IRQ_HANDLER.
Now, compiling a kernel with both non-DT and DT support enabled,
selecting MULTI_IRQ_HANDLER will break ASM irq handler used by
non-DT boards.
Therefore, we provide a C-style irq handler even for non-DT boards,
if MULTI_IRQ_HANDLER is set. By installing the C-style irq handler
in orion_irq_init this is transparent to all non-DT board files.
While the regression report was filed on Marvell Kirkwood, also
Marvell Dove non-DT boards are affected and fixed by this patch.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Reported-by: Ian Campbell <ijc@hellion.org.uk>
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 2326f04321 ("ARM: kirkwood: convert to DT irqchip and clocksource")
Fixes: f07d73e33d ("ARM: dove: convert to DT irqchip and clocksource")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
device_type is deprecated and the kernel doesn't require it in most
cases. The only exceptions for flat tree users are the "gianfar",
"ucc_geth" and "ibm,emac" bindings, and arguably that requirement could
be relaxed for ucc_geth and ibm,emac (that is a task for separate
patches though).
This patch removes references to device_type="network" from the binding
documentation where possible and removes the properties from ARM and
microblaze dts files. This patch does not modify the powerpc .dts files
since there are a much larger number of them affected and I think the
ucc_geth, ibm,emac and gianfar users should be addressed before clearing
out the references to reduce the chance of breakage.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device_type property is deprecated for the flattened device tree and
the value "ethernet-phy" has never been defined as having a useful
meaning. Neither the kernel nor u-boot depend on it. It should never
have appeared in PHY bindings. This patch removes all references to
"ethernet-phy" as a device_type value from the documentation and the
.dts files.
This patch was generated mechanically with the following command and
then verified by looking at the diff.
sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'`
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull ARM fixes from Russell King:
"Another few fixes for ARM, nothing major here"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling
ARM: 7939/1: traps: fix opcode endianness when read from user memory
ARM: 7937/1: perf_event: Silence sparse warning
ARM: 7934/1: DT/kernel: fix arch_match_cpu_phys_id to avoid erroneous match
Revert "ARM: 7908/1: mm: Fix the arm_dma_limit calculation"
At first Jakub Zawadzki noticed that some divisions by reciprocal_divide
were not correct. (off by one in some cases)
http://www.wireshark.org/~darkjames/reciprocal-buggy.c
He could also show this with BPF:
http://www.wireshark.org/~darkjames/set-and-dump-filter-k-bug.c
The reciprocal divide in linux kernel is not generic enough,
lets remove its use in BPF, as it is not worth the pain with
current cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Daniel Borkmann <dxchgb@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
gpio-samsung.h header file introduced by commit 93177be0910c
("ARM: S3C[24|64]xx: move includes back under <mach/> scope")
is required only by S3C[24|64]xx machines. Include them conditionally
to avoid the following build errors for other machine configurations.
drivers/gpio/gpio-samsung.c:35:31: fatal error: mach/gpio-samsung.h: No such file or directory
arch/arm/plat-samsung/pm-gpio.c:22:31: fatal error: mach/gpio-samsung.h: No such file or directory
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates the Armada 370/XP SATA node with the new compatible
string "marvell,armada-370-sata".
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
some missed dt nodes or props for sirf dts for 3.14.
Among them:
- add lost clocks for cphifbg
- add lost bus_width, clock and status for sdhci
- add clock, frequence-voltage table for CPU0
- add lost minigpsrtc device node
- add lost usp1_uart_nostreamctrl pin group for atlas6
- add pin group for USP0 with only RX or TX frame sync
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XVM4
-----END PGP SIGNATURE-----
Merge tag 'sirf-dts-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/dt
ARM: sirf: dts update for 3.14
From Barry Song:
some missed dt nodes or props for sirf dts for 3.14.
Among them:
- add lost clocks for cphifbg
- add lost bus_width, clock and status for sdhci
- add clock, frequence-voltage table for CPU0
- add lost minigpsrtc device node
- add lost usp1_uart_nostreamctrl pin group for atlas6
- add pin group for USP0 with only RX or TX frame sync
* tag 'sirf-dts-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- a tiny fix for the recent AT91 CCF implementation
- the switch of one platform to DT with board file removal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSzV2DAAoJEAf03oE53VmQLl0H/2KFQx+lwcg1XWd6Sq05yW7h
PtVKT6bCNZxDXGiUZ1mvZLBkDlVoQn7p35gX+NM05rsad8t9ibdmEutpe4ynPohc
Es5UpQ20txhpzGoDiIIW+pWng+fajtMV1dV8xEC4pf/d4K7HSH8k/tUwZ4GrtaJb
4eUyohznKBHdroavXao1aIuvM+MJvIu2qvxCZZPYDp0LBzTxlHR+ogcCcqO80YSL
dHG2WzbGLr+XMkxpl0bJMF9bxYarg0NsHk+GPqmnOI479rNevptSncbLQRchvwGD
auEAN8I77IwQGUpTuupssKgUrSbOU9JHTwiC2pv8zkaKdoYaIBQVPXCvmyV6kAk=
=KYgN
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
Second cleanup pull-request for 3.14:
- a tiny fix for the recent AT91 CCF implementation
- the switch of one platform to DT with board file removal
* tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91:
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Move GPIO2 and GPIO3 to be registered from the core boardfile.
- Update the defconfig.
Defconfig changes:
- Enable GPIOLIB and PL061 for the Versatile.
- Build the Versatile using EABI.
- Enable the new LEDs in the defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wyA4
-----END PGP SIGNATURE-----
Merge tag 'versatile-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
Versatile patches for v3.14:
- Move GPIO2 and GPIO3 to be registered from the core boardfile.
- Update the defconfig.
Defconfig changes:
- Enable GPIOLIB and PL061 for the Versatile.
- Build the Versatile using EABI.
- Enable the new LEDs in the defconfig.
* tag 'versatile-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: versatile: enable LEDs by default
ARM: versatile: build using EABI
ARM: versatile: enable GPIOLIB and PL061 by default
ARM: versatile: update defconfig
ARM: versatile: move GPIO2 and GPIO3 to core
Fixes to select missing configuration options, and update of the maintainer
file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=TOqs
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.14-2' of https://github.com/mripard/linux into next/soc
From Maxime Ripard:
Second round of core additions for the Allwinner SoCs
Fixes to select missing configuration options, and update of the maintainer
file.
* tag 'sunxi-core-for-3.14-2' of https://github.com/mripard/linux:
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: sun6i: Add SMP support for the Allwinner A31
dt-bindings: fix example of allwinner interrupt controller
ARM: sunxi: Register the A31 reset IP in init_time
ARM: sunxi: Select ARCH_HAS_RESET_CONTROLLER
reset: Add Allwinner SoCs Reset Controller Driver
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tliU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu into next/fixes-non-critical
From Jason Cooper:
mvebu late fixes for v3.13
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
* tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu:
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
Signed-off-by: Kevin Hilman <khilman@linaro.org>
* r8a7790 (R-Car H2) SoC
- Correct I2C controller names
This fixes the issue introduced by
b448c904f5 "ARM: shmobile: r8a7790: add I2C support"
which is queued-up for v3.14.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=DE21
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-fixes-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM Based SoC Fixes for v3.14
* r8a7790 (R-Car H2) SoC
- Correct I2C controller names
This fixes the issue introduced by
b448c904f5 "ARM: shmobile: r8a7790: add I2C support"
which is queued-up for v3.14.
* tag 'renesas-soc-fixes-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Fix I2C controller names
There was a copy/paste error when reading the nwe_pulse value.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Cc: stable <stable@vger.kernel.org> # 3.3
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Previously the custom GPIO header for the S3C24xx would in turn
bring in the custom pin control implementation from
<plat/gpio-cfg.h>. This is not good as it mixes up two
subsystems and makes the dependencies hard to track. Make
the dependency explicit by explicitly including the pin
control header where needed.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When refactoring and breaking out the includes for the
machine-specific GPIO configuration, two files were created
in <linux/platform_data/gpio-samsung-s3c[24|64]xx.h>, but as
that namespace shall be used for defining data exchanged
between machines and drivers, using it for these broad macros
and config settings is wrong.
Move the headers back into the machine-local
<mach/gpio-samsung.h> file and think about the next step.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull clocksource/clockevent updates from Daniel Lezcano:
* Axel Lin removed an unused structure defining the ids for the
bcm kona driver.
* Ezequiel Garcia enabled the timer divider only when the 25MHz
timer is not used for the armada 370 XP.
* Jingoo Han removed a pointless platform data initialization for
the sh_mtu and sh_mtu2.
* Laurent Pinchart added the clk_prepare/clk_unprepare for sh_cmt.
* Linus Walleij added a useful warning in clk_of when no clocks
are found while the old behavior was to silently hang at boot time.
* Maxime Ripard added the high speed timer drivers for the
Allwinner SoCs (A10, A13, A20). He increased the rating, shared the
irq across all available cpus and fixed the clockevent's irq
initialization for the sun4i.
* Michael Opdenacker removed the usage of the IRQF_DISABLED for the
all the timers driver located in drivers/clocksource.
* Stephen Boyd switched to sched_clock_register for the
arm_global_timer, cadence_ttc, sun4i and orion timers.
Conflicts:
drivers/clocksource/clksrc-of.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The first variants of Armada XP SoCs (A0 stepping) have issues related
to the i2c controller which prevent to use the offload mechanism and
lead to a kernel hang during boot.
This commit add quirk in the mvebu platform code to check the SoC
version and then update the compatible string for the i2c controller
according to the revision of the SoC. Currently only some OpenBlocks
AX3-4 boards are known to use an A0 revision so the check is done only
for these boards.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+: af8d1c63afcb: ARM: mvebu: Add support to get the ID and the revision of a SoC
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
All the mvebu SoCs have information related to their variant and
revision that can be read from the PCI control register.
This patch adds support for Armada XP and Armada 370. This reading of
the revision and the ID are done before the PCI initialization to
avoid any conflicts. Once these data are retrieved, the resources are
freed to let the PCI subsystem use it.
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ARMs ffs/fls implementations are not type compatible with x86, so when
they're used in combination with min()/max(), they provoke warnings.
Change these to be inline functions with the correct types, providing
the clz as a separate documentation, and document their individual
behaviours.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the syscalls needed for supporting scheduling algorithms
with extended scheduling parameters (e.g., SCHED_DEADLINE).
In general, it makes possible to specify a periodic/sporadic task,
that executes for a given amount of runtime at each instance, and is
scheduled according to the urgency of their own timing constraints,
i.e.:
- a (maximum/typical) instance execution time,
- a minimum interval between consecutive instances,
- a time constraint by which each instance must be completed.
Thus, both the data structure that holds the scheduling parameters of
the tasks and the system calls dealing with it must be extended.
Unfortunately, modifying the existing struct sched_param would break
the ABI and result in potentially serious compatibility issues with
legacy binaries.
For these reasons, this patch:
- defines the new struct sched_attr, containing all the fields
that are necessary for specifying a task in the computational
model described above;
- defines and implements the new scheduling related syscalls that
manipulate it, i.e., sched_setattr() and sched_getattr().
Syscalls are introduced for x86 (32 and 64 bits) and ARM only, as a
proof of concept and for developing and testing purposes. Making them
available on other architectures is straightforward.
Since no "user" for these new parameters is introduced in this patch,
the implementation of the new system calls is just identical to their
already existing counterpart. Future patches that implement scheduling
policies able to exploit the new data structure must also take care of
modifying the sched_*attr() calls accordingly with their own purposes.
Signed-off-by: Dario Faggioli <raistlin@linux.it>
[ Rewrote to use sched_attr. ]
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
[ Removed sched_setscheduler2() for now. ]
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1383831828-15501-3-git-send-email-juri.lelli@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS0miqAAoJEHm+PkMAQRiGbfgIAJSWEfo8ludknhPcHJabBtxu
75SQAKJlL3sBVnxEc58Rtt8gsKYQIrm4IY5Slunklsn04RxuDUIQMgFoAYR5gQwz
+Myqkw/HOqDe5VStGxtLYpWnfglxVwGDCd7ISfL9AOVy5adMWBxh4Tv+qqQc7aIZ
eF7dy+DD+C6Q3Z5OoV8s0FZDxse29vOf17Nki7+7t8WMqyegYwjoOqNeqocGKsPi
eHLrJgTl4T6jB4l9LKKC154DSKjKOTSwZMWgwK8mToyNLT/ufCiKgXloIjEvZZcY
VVKUtncdHiTf+iqVojgpGBzOEeB5DM83iiapFeDiJg8C9yBzvT8lBtA9aPb5Wgw=
=lEeV
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc8' into core/locking
Refresh the tree with the latest fixes, before applying new changes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.
This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of situations currently require the heavyweight smp_mb(),
even though there is no need to order prior stores against later
loads. Many architectures have much cheaper ways to handle these
situations, but the Linux kernel currently has no portable way
to make use of them.
This commit therefore supplies smp_load_acquire() and
smp_store_release() to remedy this situation. The new
smp_load_acquire() primitive orders the specified load against
any subsequent reads or writes, while the new smp_store_release()
primitive orders the specifed store against any prior reads or
writes. These primitives allow array-based circular FIFOs to be
implemented without an smp_mb(), and also allow a theoretical
hole in rcu_assign_pointer() to be closed at no additional
expense on most architectures.
In addition, the RCU experience transitioning from explicit
smp_read_barrier_depends() and smp_wmb() to rcu_dereference()
and rcu_assign_pointer(), respectively resulted in substantial
improvements in readability. It therefore seems likely that
replacing other explicit barriers with smp_load_acquire() and
smp_store_release() will provide similar benefits. It appears
that roughly half of the explicit barriers in core kernel code
might be so replaced.
[Changelog by PaulMck]
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Victor Kaplansky <VICTORK@il.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20131213150640.908486364@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
collie has several GPIO lines that act like keys - Sync/Wakeup button on
dock station is connected to GPIO line. Another one is connected to
on/off button. Add corresponding gpio-keys configuration.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently code has an inverted logic: opcode from user memory
is swapped to a proper endianness only in case of read error.
While normally opcode should be swapped only if it was read
correctly from user memory.
Reviewed-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/perf_event_cpu.c:274:25: warning: incorrect type in assignment (different modifiers)
arch/arm/kernel/perf_event_cpu.c:274:25: expected int ( *init_fn )( ... )
arch/arm/kernel/perf_event_cpu.c:274:25: got void const *const data
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MPIDR contains specific bitfields(MPIDR.Aff{2..0}) which uniquely
identify a CPU, in addition to some non-identifying information and
reserved bits. The ARM cpu binding defines the 'reg' property to only
contain the affinity bits, and any cpu nodes with other bits set in
their 'reg' entry are skipped.
As such it is not necessary to mask the phys_id with MPIDR_HWID_BITMASK,
and doing so could lead to matching erroneous CPU nodes in the device
tree. This patch removes the masking of the physical identifier.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The EXYNOS cpuidle driver code assumes that cpuidle core will handle
dev->state_count smaller than drv->state_count but currently this is
untrue (dev->state_count is used only for handling cpuidle state sysfs
entries and drv->state_count is used for all other cases) and will not
be fixed in the future as dev->state_count is planned to be removed.
Fix the issue by checking for the max supported idle state in AFTR
state's ->enter handler (exynos4_enter_lowpower()) and entering AFTR
mode only when cores other than CPU0 are offline.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The summary interrupt is #16 in the SPI space. Unfortunately,
when this device was translated from board files to DT we forgot
to subtract 16 from the interrupt number to translate it into a
SPI interrupt. Also, the register space is larger than 4k, increase
it appropriately so that the gpio driver doesn't try to access
registers outside of its mapping.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
ARCH_MSM is a hidden config option now so this defconfig needs to
be updated to select ARCH_MSM_DT instead. While we're here,
remove dead symbols (SSBI), drop selected symbols (ZRELADDR,
PHYLIB, USB_PHY) and enable the MSM random driver (HW_RANDOM_MSM).
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
regressions, typically boot failures or other unsafe system
configuration that causes badness.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=iLBN
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock fixes from Mike Turquette:
"Late fixes for clock drivers. All of these fixes are for user-visible
regressions, typically boot failures or other unsafe system
configuration that causes badness"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: clk-divider: fix divisor > 255 bug
clk: exynos: File scope reg_save array should depend on PM_SLEEP
clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg clock
ARM: dts: exynos5250: Fix MDMA0 clock number
clk: samsung: exynos5250: Add MDMA0 clocks
clk: samsung: exynos5250: Fix ACP gate register offset
clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
clk: samsung: exynos4: Correct SRC_MFC register
Hopefully the last set of arm-soc fixes for 3.13, or at least only a
few stray patches after this.
There are a few fixes for Renesas platforms to fixup DMA masks (this
started causing errors once the DMA API added checks for valid masks in
3.13). Two more dealing with resources for MMC and PWM setup.
There's also a few TI/OMAP/DRA fixes for smaller stuff and a fix for
compilation failures on a PXA platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=edy8
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for Renesas platforms to fixup DMA masks (this started
causing errors once the DMA API added checks for valid masks in 3.13)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: mackerel: Fix coherent DMA mask
ARM: shmobile: kzm9g: Fix coherent DMA mask
ARM: shmobile: armadillo: Fix coherent DMA mask
add pin groups for USP0 only holding one of TX and RX frame sync. this
patch matches with the change in drivers/pinctrl/sirf.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
this patch adds lost usp1_uart_nostreamctrl pin group for atlas6, which
matches with the change in drivers/pinctrl/sirf/pinctrl-atlas6.c.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
This patch adds lost minigpsrtc device node for prima2 and atlas6,
which is behind rtc-iobg and whose offset is 2000.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
prima2 and atlas6 uses cpufreq_cpu0, here we put related clock, operation
points in dtsi.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
some nodes missed bus_width, clocks and status properties, here we fix them
in prima2 and atlas6 dtsi.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
As we switch to use the watchdog core which permits more than one
active watchdog in the system, rename platform driver to
"davinci-wdt" to be identifiable.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
* qcom/soc2:
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
Signed-off-by: Olof Johansson <olof@lixom.net>
The DT based MSM platforms can join the multi-platform builds, so
introduce a DT based ARCH_MSM option. This option allows DT based
MSM platforms to be built into the multi-platform kernel. Also
introduce a hidden ARCH_MSM config that both the DT and non-DT
platform support code select to avoid churn in places that depend
on CONFIG_ARCH_MSM.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The MSM timer is only used on MSM devices that don't have the
architected timers. Introduce a hidden Kconfig option for this
driver so that we don't build it on the platforms that don't need
it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The functionality provided by clock.c in mach-msm is only needed
on proc_comm based platforms. Only build the file if proc_comm is
enabled. This prevents compile failures for platforms that are
part of the multi-platform kernel.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* qcom/drivers:
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fix compilation error when driver is compiled
in multi-platform builds.
drivers/built-in.o: In function `msm_otg_link_clk_reset':
./drivers/usb/phy/phy-msm-usb.c:314: undefined reference to `clk_reset'
./drivers/usb/phy/phy-msm-usb.c:318: undefined reference to `clk_reset'
Use platform data supplied reset handlers and adjust error
messages reported when reset sequence fail.
This is an intermediate step before adding support for reset
framework and newer targets.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Linus Walleij:
Ux500 core patches for the v3.14 series:
- Enable PRINTK_TIME
- Enable suspend with WFI
* tag 'ux500-core-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
From Christian Daudt, various defconfig udpates to bcm mobile.
* tag 'bcm-for-3.14-soc' of git://github.com/broadcom/bcm11351:
rename ARCH_BCM to ARCH_BCM_MOBILE (clocksource)
ARM: bcm_defconfig: Unset CONFIG_CRYPTO_ANSI_CPRNG
ARM: bcm_defconfig: Do not expect appended DTB
ARM: bcm_defconfig: CONFIG_OABI_COMPAT default off
Signed-off-by: Olof Johansson <olof@lixom.net>
- Delete some unused U8540 UART platform data.
- MMC/SD-fixes from Ulf Hansson so everything works with
the device tree again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vC9c
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Ux500 device tree patches for v3.14, take 2
- Delete some unused U8540 UART platform data.
- MMC/SD-fixes from Ulf Hansson so everything works with
the device tree again.
* tag 'ux500-devicetree-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: regulators: Remove dead code for SD-card regulator
ARM: ux500: Configure regulator for I/O voltage for SD-card slot
ARM: ux500: Refactor common DT configs for sdi[n] devices
ARM: ux500: delete U8540 UART auxdata
Signed-off-by: Olof Johansson <olof@lixom.net>
Revert the addition of SSI clocks to DT for the
r8a7790 (R-Car H2) and r8a7791 (R-Car M2) SoCs.
Unfortunately these patches prevent booting the
r8a7790-based Lager board and r8a7791-based Koelsch board
to the point where a serial output is available.
A solution to this problem is being sought but has not
yet been finalised so in the mean time revert the changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pTPp
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-fixes-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM Based SoC DT Fixes for v3.14
Revert the addition of SSI clocks to DT for the
r8a7790 (R-Car H2) and r8a7791 (R-Car M2) SoCs.
Unfortunately these patches prevent booting the
r8a7790-based Lager board and r8a7791-based Koelsch board
to the point where a serial output is available.
A solution to this problem is being sought but has not
yet been finalised so in the mean time revert the changes.
* tag 'renesas-dt-fixes-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
Revert "ARM: shmobile: r8a7791: Add SSI clocks in device tree"
Revert "ARM: shmobile: r8a7790: Add SSI clocks in device tree"
Signed-off-by: Olof Johansson <olof@lixom.net>
trace.h was included twice. Remove duplicate inclusion.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The THP code in KVM/ARM is a bit restrictive in not allowing a THP
to be used if the VMA is not 2MB aligned. Actually, it is not so much
the VMA that matters, but the associated memslot:
A process can perfectly mmap a region with no particular alignment
restriction, and then pass a 2MB aligned address to KVM. In this
case, KVM will only use this 2MB aligned region, and will ignore
the range between vma->vm_start and memslot->userspace_addr.
It can also choose to place this memslot at whatever alignment it
wants in the IPA space. In the end, what matters is the relative
alignment of the user space and IPA mappings with respect to a
2M page. They absolutely must be the same if you want to use THP.
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The irq data for rng module defined in hwmod data previously
missed the OMAP_INTC_START relative offset, so the interrupt
number is probably misconfigured during the DT node addition
adjusting for this OMAP_INTC_START. Interrupt #36 is associated
with a watchdog timer, so fix the rng module's interrupt to the
appropriate interrupt #52.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pl330 dmac won't be added to the list of amba devices, as it doesn't have
a clock entry.
Add the clock.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
This patch adds a label and #clock-cells property to device node of
max77686 PMIC to allow using it as a clock provider.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
After the introduction of gpmc_set_legacy(), move the GPMC width setting
to be done inside it. Currently, in the DT probed case, this is (wrongly)
done twice: first at gpmc_read_settings_dt(), and then based in the
NAND width setting.
Fix this and use only the value obtained from the DT.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce a helper function to complete the setting of some GPMC
parameters, only used when the gpmc is probed from a board file.
As such, it will go away once the DT conversion is completed.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit moves a bunch of initialization previously enclosed
under a 'if (gpmc_t)' check, to be outside such condition.
These initializations are not related to gpmc_t (timings) in any way
so it's nonsense to enclose them under such check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have standardized SoC definitions, update the
compatibility strings in board machine descriptors. Eventually, we
should just have SoC compatiblity here and all board specific stuff
should disappear.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modifying the omap2plus_defconfig to enable the audio support for
AM335x EVM and other AM33xx based devices with TLV320AIC3X connected
to McASP.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Specify the remaining input clocks (pll_ref, pll_in, and sclk_pcm_in)
for the AudioSS clock controller.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Specify pll_ref, pll_in, sclk_audio, and sclk_pcm_in for the AudioSS
clock controller.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
fiq.h contains only a function declaration and is not used by anyone
else. Move the declaration to the driver header file and remove the
unnecessary platform dependency from the driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When enabling device tree on the S3C an additional build
bug appears in the Osiris DVS board file:
CC arch/arm/mach-s3c24xx/mach-osiris-dvs.o
archh/arm/mach-s3c24xx/mach-osiris-dvs.c:
In function ‘osiris_dvs_notify’:
arch/arm/mach-s3c24xx/mach-osiris-dvs.c:77:4:
error: implicit declaration of function ‘S3C2410_GPB’
[-Werror=implicit-function-declaration]
gpio_set_value(OSIRIS_GPIO_DVS, 1);
^
Fix this by explicitly including
<linux/platform_data/gpio-samsung-s3c24xx.h>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable this option as it's required to use USB on AM335x SoC.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Cubietruck makes use of the first three i2c controllers found on the
Allwinner A20; i2c-0 is used internally for the PMIC, i2c-1 is exposed on
the board headers, and i2c-2 is used for DDC on the VGA connector. This
patch enables them in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The omap3_pmx_core pinmux device in the device tree handles the system
controller module (SCM) PADCONFS fonction. Its control registers are
split in two distinct areas, with other SCM registers in-between. Those
other registers can't thus be requested by other drivers as the memory
region gets reserved by the pinmux driver.
Split the omap3_pmx_core device tree node in two for the two memory
regions. The second region address and size depends on the SoC model.
The change in omap3.dtsi fixes an "external abort on non-linefetch" when
doing
cat /sys/kernel/debug/pinctrl/.../pins
on a Nokia N900.
Note that the core2 padconf region is different for 3430 vs 3630,
and does not exist on 3517 as noted by Nishanth Menon <nm@ti.com>.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-By: Sebastian Reichel <sre@debian.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 based on Nishant's patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 787b0d5c1c since
it is no longer required after 7909/1 was applied, and it causes
build regressions when ARM_PATCH_PHYS_VIRT is disabled and DMA_ZONE
is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When building for CONFIG_SUSPEND, add the platform suspend callbacks
to enable system suspend for ux500.
At this initial step, only WFI state is supported, which is reached
for both PM_SUSPEND_MEM and PM_SUSPEND_STANDBY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I recently noticed slow booting of a board, and without printk timestamps it's
harder to tell just where the delays are coming from. Enable it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'xen_hvm_resume_frames' used to be an 'unsigned long'
and contain the virtual address of the grants. That was OK
for most architectures (PVHVM, ARM) were the grants are contiguous
in memory. That however is not the case for PVH - in which case
we will have to do a lookup for each virtual address for the PFN.
Instead of doing that, lets make it a structure which will contain
the array of PFNs, the virtual address and the count of said PFNs.
Also provide a generic functions: gnttab_setup_auto_xlat_frames and
gnttab_free_auto_xlat_frames to populate said structure with
appropriate values for PVHVM and ARM.
To round it off, change the name from 'xen_hvm_resume_frames' to
a more descriptive one - 'xen_auto_xlat_grant_frames'.
For PVH, in patch "xen/pvh: Piggyback on PVHVM for grant driver"
we will populate the 'xen_auto_xlat_grant_frames' by ourselves.
v2 moves the xen_remap in the gnttab_setup_auto_xlat_frames
and also introduces xen_unmap for gnttab_free_auto_xlat_frames.
Suggested-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v3: Based on top of 'asm/xen/page.h: remove redundant semicolon']
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
To make the driver multiplatform-friendly, unconditional initialization
in an initcall is replaced with a platform driver probed only if
respective platform device is registered.
Tested at: Exynos4210 (TRATS) and Exynos4412 (TRATS2)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJSxY6TAAoJEIv3Hb8G/XruUcgP/001H5qqDZWtEk2Z1XvOUPgF
MfFprrNcPpLhLmBnvDpR5mUrcMIp4t/4GcWClmX58zcsZfcQP5YF81oGGiQy+U13
Yu94H+sWihrms5h8GSkqEhB5YSvcIOfs4rtAeNl/g2su7i+l4loF/xofXpj09+qp
xnmKJ8yfB5RD822StgrkoMu7vxzYyK05j8IasSH54vsO9X3Z3jTWuAKdQFKZoZp4
xBGjtIwoyyHndWAlhl1nIj1dvaDgx+gF25qRUrfShfE51R4BNzmvpgiN1mpQTjCl
JpYDJqZ1h7FL883ZXiz7SfRVv4H2GaEWqz+zxgVfHkO45lIL3Eyn1zhSKas4pRFH
KZscKBvT/YEgIQjBW4+VdMuMM0NWIzvYp1BM2/l88KvUgXYiS0EOM5UjYJatKwIO
MW4ZLpIsMiJlN8OygBTaZOZQaY8rbbdVn5KFsgkL0zl7uZzmbYCqhxKrXZfTKyx/
ieEGRmqjrcuguVDPNSsd9TZ/LUm3kTCSzpr3gvAXjK+29DbVrs6fX1lQ0RCxvACQ
8gBjD6ZsVFcsGSbWbPEoDi+qtKielZBjbSrgTDNkRqE/6yqg+UUZVSJJ6kkEA14o
swE+8mGrUhdv5TvpTjJactnBZeUpFbmLm4TE/r695dfwcr6wX7cK41gMVo7bE9fk
2rYzz35ed29q8OfJI/54
=0B0x
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes
Samsung Clock fixes for 3.13-rc7
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
This fixes the issue introduced by the following commit:
b448c904f5 "ARM: shmobile: r8a7790: add I2C support"
The R8A7790 is an R-Car Gen2 SoC. The clock division factor
(CDF) width is 3 bits on Gen2 as opposed to 2 bits on Gen1.
Fix the device names for R8A7790 SoC to make the R-Car I2C
driver configure the hardware properly.
Changes in V2:
* rebased on top of the latest branch;
* capitalized ARM in the subject line;
* noted the commit that caused the issue in the log.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull ARM fixes from Russell King:
"Another set of small fixes for ARM, covering various areas.
Laura fixed a long standing issue with virt_addr_valid() failing to
handle holes in memory. Steve found a problem with dcache flushing
for compound pages. I fixed another bug in footbridge stuff causing
time to tick slowly, and also a problem with the AES code which can
cause linker errors.
A patch from Rob which fixes Xen problems induced by a lack of
consistency in our naming of ioremap_cache() - which thankfully has
very few users"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7933/1: rename ioremap_cached to ioremap_cache
ARM: fix "bad mode in ... handler" message for undefined instructions
CRYPTO: Fix more AES build errors
ARM: 7931/1: Correct virt_addr_valid
ARM: 7923/1: mm: fix dcache flush logic for compound high pages
ARM: fix footbridge clockevent device
ioremap_cache is more aligned with other architectures.
There are only 2 users of this in the kernel: pxa2xx-flash and Xen.
This fixes Xen build failures on arm64:
drivers/tty/hvc/hvc_xen.c:233:2: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/grant-table.c:1174:3: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/xenbus/xenbus_probe.c:778:4: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The array was missing the final entry for the undefined instruction
exception handler; this commit adds it.
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Building a multi-arch kernel results in:
arch/arm/crypto/built-in.o: In function `aesbs_xts_decrypt':
sha1_glue.c:(.text+0x15c8): undefined reference to `bsaes_xts_decrypt'
arch/arm/crypto/built-in.o: In function `aesbs_xts_encrypt':
sha1_glue.c:(.text+0x1664): undefined reference to `bsaes_xts_encrypt'
arch/arm/crypto/built-in.o: In function `aesbs_ctr_encrypt':
sha1_glue.c:(.text+0x184c): undefined reference to `bsaes_ctr32_encrypt_blocks'
arch/arm/crypto/built-in.o: In function `aesbs_cbc_decrypt':
sha1_glue.c:(.text+0x19b4): undefined reference to `bsaes_cbc_encrypt'
This code is already runtime-conditional on NEON being supported, so
there's no point compiling it out depending on the minimum build
architecture.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable the DCP by default on both i.MX23 and i.MX28.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a minimal board dts file for EXYNOS4412 based FriendlyARM's
TINY4412 board. This patch including support peripherals like
UART, SD card on SDMMC2 port and GPIO connected LEDs.
Signed-off-by: Alex Ling <kasimling@gmail.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Arndale Octa board is based on Exynos5420 SoC. This patch
adds the basic support required for booting it through DT.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cCZc
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
From Linus Walleij:
Some Integrator patches that matured for v3.14:
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
* tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
ARM: integrator: Default enable ARM_PATCH_PHYS_VIRT, AUTO_ZRELADDR
Signed-off-by: Olof Johansson <olof@lixom.net>
This mostly adds the reset controller initialisation for the A31 and the SMP
operations for this SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=zEQv
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.14' of https://github.com/mripard/linux into next/drivers
From Maxime Ripard:
Allwinner core changes for 3.14
This mostly adds the reset controller initialisation for the A31 and the SMP
operations for this SoC.
* tag 'sunxi-core-for-3.14' of https://github.com/mripard/linux:
ARM: sun6i: Add SMP support for the Allwinner A31
dt-bindings: fix example of allwinner interrupt controller
ARM: sunxi: Register the A31 reset IP in init_time
ARM: sunxi: Select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSwiPBAAoJEFBXWFqHsHzO3/AIALlP6m/7taIQW5wO4o4aqdwk
GsN7IdsfWH/biG9VyxgpIoJKUqaOJckGA0eyLSeEG7p78xlf0n7cVPUNwzz9z1Vc
zxLSaVNznVOa4fTIsbMK9U+gUP931hjXskxD3tH98MUFqlM0JLQYoofr/lXG7Esf
N2p8B9aUND3WSxDa+d+CsW0B3FBj1piOQDMDgrdc3p7kjcAJs31KaKfUa06o7gzM
a81OaD9Vk0ONf44wh1LGlg0hDRsatQOa4tUTimeV14CnESKqsKxT4qAJ6pZLdfOt
KyRqSk4f4mkpimv4bGdhXTIsIko1CD9wg7G9fsSaolh3OEP0yyNf1savR1fmwCI=
=Hhbl
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
i.MX SoC changes for 3.14:
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
* tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits)
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
ARM: imx: update imx_v6_v7_defconfig
ARM: imx6sl: Add missing spba clock to clock tree
ARM: imx6sl: Add missing pll4_audio_div to the clock tree
ARM: imx6: Derive spdif clock from pll3_pfd3_454m
ARM: imx: use __initconst for const init definition
ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition
ARM i.MX5: set CAN peripheral clock to 24 MHz parent
ARM: imx: pllv1: Fix PLL calculation for i.MX27
ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53
ARM: imx: imx53: Add SATA PHY clock
ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen
ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END
ARM: imx: select PINCTRL at sub-architecure level
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Rebuild bcm2835_defconfig using "make bcm2835_defconfig;
make savedefconfig", and add the following features:
* Enable the DWC2 USB controller present in the BCM2835 SoC.
* Enable drivers for various USB-hosted devices, which make the
controller useful.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The BCM2835 SoC contains a DWC2 USB controller. Add this to the DT.
Set up the pin controller to fully enable the USB controller on the
Raspberry Pi. The GPIO setup works because the default output value for
GPIO 6 (LAN_RUN/n_reset) just happens to be 1, which enables the
USB/LAN chip.
Note that you'll need a U-Boot which enables power to the USB controller;
search for U-Boot patch "ARM: rpi_b: power on SDHCI and USB HW modules".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace "is use" by "is used" and remove a comma.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Various DT related patches, but mostly:
- Support for the Olimex A13-olinuxino-micro
- Added the needed IP in the A31 for the HS timer support and SMP bringup
- A10 and A20 RTC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=kYub
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.14' of https://github.com/mripard/linux into next/dt
From Maxime Ripard:
Allwinner sunXi DT Additions for 3.14
Various DT related patches, but mostly:
- Support for the Olimex A13-olinuxino-micro
- Added the needed IP in the A31 for the HS timer support and SMP bringup
- A10 and A20 RTC
* tag 'sunxi-dt-for-3.14' of https://github.com/mripard/linux:
ARM: sun6i: dt: Add IP needed to bring up the additional cores
ARM: dts: sun5i: Add new sun5i-a13-olinuxino-micro board
ARM: sun6i: Add the reset controller to the DTSI
ARM: sunxi: dt: add EMAC aliases
ARM: dts: sun4i/sun7i: add RTC node
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds