Move this logic to a function, because it will be reused later.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-raid1 is setting the 'DM_KCOPYD_IGNORE_ERROR' flag unconditionally
when assigning kcopyd work. kcopyd is responsible for copying an
assigned section of disk to one or more other disks. The
'DM_KCOPYD_IGNORE_ERROR' flag affects kcopyd in the following way:
When not set:
kcopyd will immediately stop the copy operation when an error is
encountered.
When set:
kcopyd will try to proceed regardless of errors and try to continue
copying any remaining amount.
Since dm-raid1 tracks regions of the address space that are (or
are not) in sync and it now has the ability to handle these
errors, we can safely enable this optimization. This optimization
is conditional on whether mirror error handling has been enabled.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves 'is_active' from struct dm_path to struct pgpath
as it does not need exporting.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch allows path errors from the multipath ctr function to
propagate up to userspace as errno values from the ioctl() call.
This is in response to
https://www.redhat.com/archives/dm-devel/2008-May/msg00000.html
and
https://bugzilla.redhat.com/show_bug.cgi?id=444421
The patch only lets through the errors that it needs to in order to
get the path errors from parse_path().
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Referencing cm_node after it is freed via rem_ref_cm_node() causes a
slab corruption. There is no need to set cm_node->cm_id to NULL in
mini_cm_close().
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix warnings caught by David Miller on sparc64
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to modulus the queue number in ->hard_start_xmit() since the
core is going to do that for you modulus ->real_num_tx_queues.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
same patch as e1000e
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before, the driver would not care about the return codes from pci_map_*
functions. This could be potentially dangerous if a mapping failed.
Now, we will check all pci_map_* calls. On the transmit side, we switch
to use the new function skb_dma_map(). On the receive side, we add
pci_dma_mapping_error().
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this new firmware, the driver no longer has to modify the
TCP/IP header fields when transmitting TSO packets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check netif_running() state in most ethtool operations
and properly handle the !netif_running() state where the chip is
in an uninitailzed state or low power state that may not accept
any MMIO.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This logic is used in bnx2_close() and bnx2_suspend() and
so should be separated out into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to export the governors for use as the default governor,
because the default governor will be built-in anyway and we can access
the symbol directly.
This also fixes the following sparse warnings:
drivers/cpufreq/cpufreq_conservative.c:578:25: warning: symbol 'cpufreq_gov_conservative' was not declared. Should it be static?
drivers/cpufreq/cpufreq_ondemand.c:582:25: warning: symbol 'cpufreq_gov_ondemand' was not declared. Should it be static?
drivers/cpufreq/cpufreq_performance.c:39:25: warning: symbol 'cpufreq_gov_performance' was not declared. Should it be static?
drivers/cpufreq/cpufreq_powersave.c:38:25: warning: symbol 'cpufreq_gov_powersave' was not declared. Should it be static?
drivers/cpufreq/cpufreq_userspace.c:190:25: warning: symbol 'cpufreq_gov_userspace' was not declared. Should it be static?
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Use get_cpu_idle_time_us() to get micro-accounted idle information.
This enables ondemand to get more accurate idle and busy timings
than the jiffy based calculation. As a result, we can decrease
the ondemand safety gaurd band from 80-10 to 95-3.
Results in more aggressive power savings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Use a parameter for down differential, instead of hardcoded 10%. Follow-on
patch changes the down-differential dynamically, based on whether
we are using idle micro-accounting or not.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Preparatory changes for doing idle micro-accounting in ondemand governor.
get_cpu_idle_time() gets extra parameter and returns idle time and also the
wall time that corresponds to the idle time measurement.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Change the load calculation algorithm in ondemand to work well with software
coordination of frequency across the dependent cpus.
Multiply individual CPU utilization with the average freq of that logical CPU
during the measurement interval (using getavg call). And find the max CPU
utilization number in terms of CPU freq. That number is then used to
get to the target freq for next sampling interval.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add a cpu parameter to __cpufreq_driver_getavg(). This is needed for software
cpufreq coordination where policy->cpu may not be same as the CPU on which we
want to getavg frequency.
A follow-on patch will use this parameter to getavg freq from all cpus
in policy->cpus.
Change since last patch. Fix the offline/online and suspend/resume
oops reported by Youquan Song <youquan.song@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Venki Pallipadi made a similar change to the ondemand governor a while
back (in commit 28287033e1). It seems to
work just as well in the conservative governor, leading to fewer wakeups
as reported by powertop.
Signed-off-by: Ben Slusky <sluskyb@paranoiacs.org>
Signed-off-by: Dave Jones <davej@redhat.com>
After calling cpufreq_cpu_get, error handling code should call
cpufreq_cpu_put.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r@
expression x,E;
statement S;
position p1,p2,p3;
@@
(
if ((x = cpufreq_cpu_get@p1(...)) == NULL || ...) S
|
x = cpufreq_cpu_get@p1(...)
... when != x
if (x == NULL || ...) S
)
<...
if@p3 (...) { ... when != cpufreq_cpu_put(x)
when != if (x) { ... cpufreq_cpu_put(x); ...}
return@p2 ...;
}
...>
(
return x;
|
return 0;
|
x = E
|
E = x
|
cpufreq_cpu_put(x)
)
@exists@
position r.p1,r.p2,r.p3;
expression x;
int ret != 0;
statement S;
@@
* x = cpufreq_cpu_get@p1(...)
<...
* if@p3 (...)
S
...>
* return@p2 \(NULL\|ret\);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Jones <davej@redhat.com>
Add error handling for cpufreq_register_governor() error
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Dave Jones <davej@redhat.com>
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Creates a name file in the sysfs directory, that
is needed for the libsensors library to work.
Also rename fan1_pwm to pwm1 and scale its value as needed.
This fixes bug #11520:
http://bugzilla.kernel.org/show_bug.cgi?id=11520
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;
then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.
Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts gdrom to use __blk_end_request() directly
so that end_{queued|dequeued}_request() can be removed.
gd.transfer is '1' in error cases and '0' in non-error cases,
so gdrom hasn't been propagating any error code to the block layer.
We can just convert error cases to '-EIO'.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts memstick to use __blk_end_request() directly
so that end_{queued|dequeued}_request() can be removed.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts virtio_blk to use __blk_end_request() directly
so that end_{queued|dequeued}_request() can be removed.
Related 'uptodate' argument is converted to 'error'.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The current floppy_struct allows floppies to number sectors starting
from 0 or 1. This patch allows arbitrary first-sector numbers - for
example, 0xC1 for Amstrad CPC disks.
This extends the existing 1-bit field (FD_ZEROBASED, bit 2 of stretch)
to 8 bits (FD_SECTMASK, bits 2 to 9).
Currently 0x00 denotes a first sector number of 1, and 0x01 denotes a
first sector number of 0. We extend this by interpreting FD_SECTMASK
as the first sector number with the LSB flipped.
Signed-off-by: Keith Wansbrough <keith@lochan.org>
Cc: Alain Knaff <alain@linux.lu>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix cciss SCSI rescan code to better notice device changes.
If you hot-unplug a tape drive, then hot-plug a different
tape drive into the same slot in a storage enclosure,
the cciss driver wouldn't notice anything had changed, as
it was only looking at the LUN address and device type.
Now it looks at the inquiry page 0x83 device identifier,
and vendor and model strings as well.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until recently, the maximum number of xvd block devices you could attach
to a Xen domU was 16. This limitation turned out to be problematic for
some users, so it was expanded to handle a much larger number of disks.
However, this requires a couple of changes in the way that blkfront
scans for disks. This functionality is already present in the Xen
linux-2.6.18-xen.hg tree; the attached patch adds this functionality to
the mainline xen-blkfront implementation. I successfully tested it on a
2.6.25 tree, and build tested it on 2.6.27-rc3.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blk_rq_unmap_user in sg_finish_rem_req can take care of all the cases.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sg_read_xfer was used to copy data to user space for READ
commands. blk_rq_unmap_user does the job so sg_read_xfer does nothing
useful.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sg_write_xfer was used to copy data from user space for WRITE
commands. blk_rq_map_user_iov and blk_rq_map_user do the job so
sg_write_xfer does nothing useful.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Calling blk_rq_map_user() at a single place is better than at
different two places. It makes the code more understandable.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
__sg_start_req() was used temporarily to call blk_get_request() during
converting sg to use the block layer.
Now sg always calls blk_get_request() so we can move blk_get_request()
to sg_start_req(). We don't need __sg_start_req anymore.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's not used for anything useful after the block layer conversion.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sg had lots of the own functions for the direct IO but now sg uses the
block layer functions for it. There are only five lines for the direct
IO. SG_ALLOW_DIO_CODE define was used to compile out the direct IO
code but we don't need the define. If someone wants to remove the
direct IO code, he can do easily without the define.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
old sg_rq_end_io() was used to wrap sg_cmd_done during converting sg
to use the block layer (in order to cover the difference
scsi_execute_async and blk_execute_rq_nowait). Now we don't need it so
let's remove it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Modify the SCSI disk driver to call the revalidate_disk()
wrapper. This allows us to do some housekeeping such as accounting for
a disk being resized online. The wrapper will call
sd_revalidate_disk() at the appropriate time.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the older SG interface, we don't know a user-space address to
trasfer data when executing a SCSI command. So we can't pass a
user-space address to blk_rq_map_user.
This patch fixes sg to pass a NULL user-space address to
blk_rq_map_user so that it just sets up a request and bios with page
frames propely without data transfer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts the indirect IO path (including mmap IO and old
struct sg_header) to use the block layer functions (blk_get_request,
blk_execute_rq_nowait, blk_rq_map_user, etc) instead of
scsi_execute_async().
[Jens: fixed compile error with SCSI logging enabled]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts the direct IO path (SG_FLAG_DIRECT_IO) to use the
block layer functions (blk_get_request, blk_execute_rq_nowait,
blk_rq_map_user, etc) instead of scsi_execute_async().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts the non data path to use the block layer functions
(blk_get_request, blk_execute_rq_nowait, etc) instead of uses
scsi_execute_async().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch introduces struct rq_map_data to enable bio_copy_use_iov()
use reserved pages.
Currently, bio_copy_user_iov allocates bounce pages but
drivers/scsi/sg.c wants to allocate pages by itself and use
them. struct rq_map_data can be used to pass allocated pages to
bio_copy_user_iov.
The current users of bio_copy_user_iov simply passes NULL (they don't
want to use pre-allocated pages).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Currently, blk_rq_map_user and blk_rq_map_user_iov always do
GFP_KERNEL allocation.
This adds gfp_mask argument to blk_rq_map_user and blk_rq_map_user_iov
so sg can use it (sg always does GFP_ATOMIC allocation).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that disk and partition handlings are mostly unified, it's easy to
allow disk to have extended device number. This patch makes
add_disk() use extended device number if disk->minors is zero. Both
sd and ide-disk are updated to use this.
* sd_format_disk_name() is implemented which can generically determine
the drive name. This removes disk number restriction stemming from
limited device names.
* If sd index goes over SD_MAX_DISKS (which can be increased now BTW),
sd simply doesn't initialize minors letting block layer choose
extended device number.
* If CONFIG_DEBUG_EXT_DEVT is set, both sd and ide-disk always set
minors to 0 and use extended device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With previous changes, it's meaningless to limit the number of
partitions. Replace @ext_minors with GENHD_FL_EXT_DEVT such that
setting the flag allows the disk to have maximum number of allowed
partitions (only limited by the number of entries in parsed_partitions
as determined by MAX_PART constant).
This kills not-too-pretty alloc_disk_ext[_node]() functions and makes
@minors parameter to alloc_disk[_node]() unnecessary. The parameter
is left alone to avoid disturbing the users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now, bdev->bd_part is set only if the bdev was for parts other
than part0. This patch makes bdev->bd_part always set so that code
paths don't have to differenciate common handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move disk->capacity to part0->nr_sects and convert all users who
directly accessed the field to use {get|set}_capacity(). This is done
early to allow the __dev field to be moved.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement {disk|part}_to_dev() and use them to access generic device
instead of directly dereferencing {disk|part}->dev. To make sure no
user is left behind, rename generic devices fields to __dev.
This is in preparation of unifying partition 0 handling with other
partitions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Extended devt introduces non-contiguos device numbers. This patch
implements a debug option which forces most devt allocations to be
from the extended area and spreads them out. This is enabled by
default if DEBUG_KERNEL is set and achieves...
1. Detects code paths in kernel or userland which expect predetermined
consecutive device numbers.
2. When something goes wrong, avoid corruption as adding to the minor
of earlier partition won't lead to the wrong but valid device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Update sd and ide-disk such that they can take advantage of extended
minors.
ide-disk already has 64 minors per device and currently doesn't use
extended minors although after this patch it can be turned on by
simply tweaking constants.
sd only had 16 minors per device causing problems on certain peculiar
configurations. This patch lifts the restriction and enables it to
use upto 64 minors.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters. It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.
This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access). diskstats access
should always be enclosed between the two functions. As such, there's
no need for the versions which disables preemption. They're removed
and double underbars ones are renamed to drop the underbars. As an
extra argument is added, there's no danger of using the old version
unconverted.
disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.
This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others. Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
disk->part[] is protected by its matching bdev's lock. However,
non-critical accesses like collecting stats and printing out sysfs and
proc information used to be performed without any locking. As
partitions can come and go dynamically, partitions can go away
underneath those non-critical accesses. As some of those accesses are
writes, this theoretically can lead to silent corruption.
This patch fixes the race by using RCU for the partition array and dev
reference counter to hold partitions.
* Rename disk->part[] to disk->__part[] to make sure no one outside
genhd layer proper accesses it directly.
* Use RCU for disk->__part[] dereferencing.
* Implement disk_{get|put}_part() which can be used to get and put
partitions from gendisk respectively.
* Iterators are implemented to help iterate through all partitions
safely.
* Functions which require RCU readlock are marked with _rcu suffix.
* Use disk_put_part() in __blkdev_put() instead of directly putting
the contained kobject.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Implement disk_devt() and part_devt() and use them to directly
access devt instead of computing it from ->major and ->first_minor.
Note that all references to ->major and ->first_minor outside of
block layer is used to determine devt of the disk (the part0) and as
->major and ->first_minor will continue to represent devt for the
disk, converting these users aren't strictly necessary. However,
convert them for consistency.
* Implement disk_max_parts() to avoid directly deferencing
genhd->minors.
* Update bdget_disk() such that it doesn't assume consecutive minor
space.
* Move devt computation from register_disk() to add_disk() and make it
the only one (all other usages use the initially determined value).
These changes clean up the code and will help disk->part dereference
fix and extended block device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the following misc updates in preparation for
disk->part dereference fix and extended block devt support.
* implment part_to_disk()
* fix comment about gendisk->part indexing
* rename get_part() to disk_map_sector()
* don't use n which is always zero while printing disk information in
diskstats_show()
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Iterating over entries using callback usually isn't too fun especially
when the entry being iterated over can't be manipulated freely. This
patch converts class->p->class_devices to klist and implements class
device iterator so that the users can freely build their own control
structure. The users are also free to call back into class code
without worrying about locking.
class_for_each_device() and class_find_device() are converted to use
the new iterators, so their users don't have to worry about locking
anymore either.
Note: This depends on klist-dont-iterate-over-deleted-entries patch
because class_intf->add/remove_dev() depends on proper synchronization
with device removal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
raid5 can overflow with more than 255 stripes, and we can increase it
to an int for free on both 32 and 64-bit archs due to the padding.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove hw_segments field from struct bio and struct request. Without virtual
merge accounting they have no purpose.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
struct request has an ioprio member but it is never updated because
currently bios do not hold io context information. The implication of
this is that virtio_blk ends up passing useless information to the
backend driver.
That said, some IO schedulers such as CFQ do store io context
information in struct request, but use private members for that, which
means that that information cannot be directly accessed in a IO
scheduler-independent way.
This patch adds a function to obtain the ioprio of a request. We should
avoid accessing ioprio directly and use this function instead, so that
its users do not have to care about future changes in block layer
structures or what the currently active IO controller is.
This patch does not introduce any functional changes but paves the way
for future clean-ups and enhancements.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It was only used by ps3disk, and it should probably have been
REQ_TYPE_LINUX_BLOCK + REQ_LB_OP_FLUSH.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We can benefit from knowing that the file system no longer cares about
the contents of certain sectors, by throwing them away immediately and
then never having to garbage collect them, and using the extra free
space to make our operations more efficient. Do so.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Set RLKEY bit in the HW context for kernel QPs so that kernel QPs can
use the reserved L_Key for memory reference.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
drivers/net/jme.c:1598: warning: ‘jme_set_100m_half’ defined but not used
drivers/net/jme.c:1618: warning: ‘jme_wait_link’ defined but not used
Signed-off-by: David S. Miller <davem@davemloft.net>
Advances the driver version after modification.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix IRQ handle bug when interrupt mode.
The driver was incorrectly handled and returned IRQ_HANDLED
while the device is not generating the interrupt.
It happened due to faulty determination of interrupt status register.
Found by: "Ethan" <ethanhsiao@jmicron.com>
Fixed by: "akeemting" <akeem@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Set bit 5 of GPREG1 to 1 to enable hardware workaround for half-duplex
mode. Which the MAC processor generates CRS/COL by itself instead of
receive it from PHY processor.
2. Set bit 6 of GPREG1 to 1 to enable hardware workaround that masks the
MAC processor working right while calculating IPv6 RSS in 10/100
mode.
3. Group the workaround codes all together.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SR PHY.
Auto-detect phy module type, and report type changes.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic code to manage interrupt driven PHYs.
Do not reset the phy after link parameters update,
the new values might get lost.
Return early from link change notification
when the link parameters remain unchanged.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not require PHY interrupts to be connected to GPIs in ascending order.
Base interrupt availability both on PHYs supporting them and on GPIs being
hooked up. Allows boards to specify interrupt GPIs though the PHYs don't
use them.
Remove spurious PHY interrupts due to clearing T3DBG interrupts before
setting their polarity.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second step in overall phy layer reorganization.
Clean up the port_type_info structure.
Support coextistence of clause 22 and clause 45 MDIO devices.
Select the type of MDIO transaction on a per transaction basis.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step towards overall PHY layering re-organization.
Allow a status return when a PHY is reset.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a queue set per core, up to the maximum of available qsets.
Share the queue sets on multi port adapters.
Rename MSI-X interrupt vectors ethX-N, N being the queue set number.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when a fatal error occurs, bring ports down, reset the chip,
and bring ports back up.
Factorize code used for both EEH and fatal error recovery.
Fix timer usage when bringing up/resetting sge queue sets.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The write barrier should be used before starting a DMA transfer. This fixes
a problem, where almost all packets received on another machine had garbled
content. Tested with an RTL8100C on a MIPS machine.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
there's several drivers that have use "tx_timeout" for the .. tx
timeout function. All fine with that, they're static, however for
doing stats on how often which driver hits the timeout it's a tad
unfortunate. The patch below gives the ones I found in the
kerneloops.org database unique names.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with CONFIG_USB_DEBUG, don't create logspam from
the USB networking drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since recent kernel (2.6.26 or 2.6.27) the PCI wakeup functions are
influenced by generic device ability and configuration when enabling
PCI-device triggered wake-up.
This patch causes WoL setting to enable/disable device's wish to
be permitted to wake-up the host when changing WoL options and
also during device probing.
Without this patch one has write 'enabled' to
/sys/bus/pci/devices/0000:02:08.0/power/wakeup
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the chip and handling it's power management settings
also remember wether WoL feature is enabled.
Without this patch one has to call ethtool to change WoL settings
for this flag to be set and any WoL being enabled on suspend to
RAM.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device's carrier status is controlled via the functions
netif_carrier_on() and netif_carrier_off(). These set or clear a bit
indicating the carrier (aka lower level link) is down, and if the state
changed, they fire off a routing netlink event.
Add a call to netif_carrier_off() before register_netdev() so that the
newly created device will be set to carrier down. Then when the carrier
comes up for the first time, a netlink event will be generated, as the
carrier changed from down to up. Otherwise the initial carrier up will
appear to be changing the status from up to up, and so no event is
generated since that's not a change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv643xx_eth uses ip_hdr() (defined in linux/ip.h), but relied on
another header file to include the needed header file indirectly.
In latest net-next this indirect include chain is gone, so the
driver fails to build. Include linux/ip.h explicitly to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lockdep warning:
=================================
[ INFO: inconsistent lock state ]
2.6.27-rc7 #3
---------------------------------
inconsistent {in-softirq-W} -> {softirq-on-W} usage.
syslogd/2474 [HC0[0]:SC0[0]:HE1:SE1] takes:
(_xmit_ETHER#2){-+..}, at: [<c0265562>] netpoll_send_skb+0x132/0x190
...
is caused by unconditional local_irq_disable()/local_irq_enable() in
disable_irq_lockdep()/enable_irq_lockdep() used by __ei_poll(). Since
netconsole/netpoll always calls dev->poll_controller() with local irqs
disabled, disable_irq()/enable_irq() instead is safe and enough (like
e.g. in 3c509 or 8139xx drivers).
Reported-and-tested-by: Bernard Pidoux F6BVP <f6bvp@free.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out by Breno Leitao <leitao@linux.vnet.ibm.com> that
ixgb would crash on PPC when an IOMMU was in use, if change_mtu was
called.
It appears to be a pretty simple issue in the driver that wasn't discovered
because most systems don't run with an IOMMU. The driver needs to only unmap
buffers that are mapped (duh).
CC: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since e1000e has been existance in linux-2.6, we've
never released the hardware semaphore after a successful
write to the SPI EEPROM. I guess we don't write to
SPI EEPROM much -- but those few of us that do appreciate
it when we can later read from the EEPROM without having
to reboot.
Found-by: Nick Van Fossen <Nick.VanFossen@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Reviewed-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN9500 USB2.0 10/100 ethernet
adapter.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
Add multiqueue TX support to myri10ge.
[ Removed reference to deprecated CONFIG_NETDEVICES_MULTIQUEUE and
NETIF_F_MULTI_QUEUE ]
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the EXPERIMENTAL label from the atl1 driver and change the vendor
name to include Attansic's successor, Atheros. We'll leave Attansic in
the name since Attansic's PCI ID (1969) is encoded in the PCI config and
is what users encounter on their systems.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_LLTX is deprecated. Remove private TX locking from the driver
and remove the NETIF_F_LLTX feature flag.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
See http://marc.info/?l=linux-netdev&m=121931988219314&w=2
Stop the queue and turn off carrier to prevent transmit timeouts
when the cable is unplugged/replugged.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return is useful to caller, driver shouldn't miss it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pauseparam is set
On Wednesday 24 September 2008 07:47, Stephen Hemminger wrote:
> On Mon, 22 Sep 2008 14:52:17 -0700
>
> akpm@linux-foundation.org wrote:
> > From: "Xiaoming.Zhang" <Xiaoming.Zhang@resilience.com>
> >
> > We have an issue of the skge driver: The card won't work when it's
> > options are changed. Here's the hardware info:
> >
> > # lspci -v
> > 05:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
> > Gigabit Ethernet Controller (rev 13) Subsystem: Marvell Technology Group
> > Ltd. Marvell RDK-8001 Flags: bus master, 66MHz, medium devsel, latency
> > 32, IRQ 16 Memory at d042c000 (32-bit, non-prefetchable) [size=16K] I/O
> > ports at d000 [size=256]
> > [virtual] Expansion ROM at 20400000 [disabled] [size=128K]
> > Capabilities: [48] Power Management version 2
> > Capabilities: [50] Vital Product Data
> >
> > The happens in both Linux-2.6.26(skge version 1.23) and RHEL5.2(skge
> > version 1.6).
> >
> > For example, at first it is set to "speed 1000 duplex full auto-neg on"
> > and it works, then run
> >
> > ethtool -s <ethx> autoneg off
> > or ethtool -s <ethx> speed 100 duplex full autoneg off
> >
> > Then it will stop working. After that if we restart the interface:
> >
> > ifconifg <ethx> down
> > ifconfig <ethx> up
> >
> > It will work again. And `ethtool -A' has the same issue.
> >
> > So we think after setting the options, the interface should be restarted.
> >
> > Signed-off-by: Zhang Xiaoming <xiaoming.zhang@resilience.com>
> > Cc: Stephen Hemminger <shemminger@vyatta.com>
> > Cc: Jeff Garzik <jeff@garzik.org>
> > Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
> > ---
> >
> > drivers/net/skge.c | 12 ++++++++----
> > 1 file changed, 8 insertions(+), 4 deletions(-)
> >
> > diff -puN
> > drivers/net/skge.c~driver-net-skgec-restart-the-interface-when-its-option
> >s-or-pauseparam-is-set drivers/net/skge.c ---
> > a/drivers/net/skge.c~driver-net-skgec-restart-the-interface-when-its-opti
> >ons-or-pauseparam-is-set +++ a/drivers/net/skge.c
> > @@ -353,8 +353,10 @@ static int skge_set_settings(struct net_
> > skge->autoneg = ecmd->autoneg;
> > skge->advertising = ecmd->advertising;
> >
> > - if (netif_running(dev))
> > - skge_phy_reset(skge);
> > + if (netif_running(dev)) {
> > + skge_down(dev);
> > + skge_up(dev);
> > + }
> >
> > return (0);
> > }
> > @@ -595,8 +597,10 @@ static int skge_set_pauseparam(struct ne
> > skge->flow_control = FLOW_MODE_NONE;
> > }
> >
> > - if (netif_running(dev))
> > - skge_phy_reset(skge);
> > + if (netif_running(dev)) {
> > + skge_down(dev);
> > + skge_up(dev);
> > + }
> >
> > return 0;
> > }
>
> Since skge_up can fail because of out of memory, this code needs to
> check the return value. And then if it fails the "limbo state" needs
> to be handled in skge_down.
How about like this? It is tested.
Thank you.
Signed-off-by: Zhang Xiaoming <xiaoming.zhang@resilience.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SGE queue set timer might access registers while in EEH recovery,
triggering an EEH error loop. Stop all timers early in EEH process.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NETIF_F_LLTX is set, the atlx driver will use a private lock.
But in recent kernels this implementation seems redundant and
can cause problems where AF_PACKET sees things twice. Since
NETIF_F_LLTX is marked as deprecated and shouldn't be used in
new driver, this patch removes NETIF_F_LLTX and adds a mmiowb
before sending packet. I have tested this driver on a Eee PC.
It works well.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Acked-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way the phy layer will respond to a change in phy state immediately,
instead of up to one second later when the state machine timer runs.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's aneg is configured and restarted whenever the link is brought up,
e.g. when DHCP is started after the kernel has booted. This can take the
link down for several seconds while auto-negotiation is redone.
If the advertised features haven't changed, then it shouldn't be necessary
to bring down the link and start auto-negotiation over again.
genphy_config_advert() is enhanced to return 0 when the advertised features
haven't been changed and >0 when they have been.
genphy_config_aneg() then uses this information to not call
genphy_restart_aneg() if there has been no change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netconsole support for Atheros L2 10/100 network device.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Acked-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes EMAC soft reset on 460EX/GT when no external clock is
available.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the SIOCGMIIPHY case fall through properly (it is supposed
to not only return the ID of the default PHY but also to read from
that PHY), and make phy_mii_ioctl() return the same error code as
generic_mii_ioctl() in case of an unsupported operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Fix tcp_hybla zero congestion window growth with small rho and large cwnd.
net: Fix netdev_run_todo dead-lock
tcp: Fix possible double-ack w/ user dma
net: only invoke dev->change_rx_flags when device is UP
netrom: Fix sock_orphan() use in nr_release
ax25: Quick fix for making sure unaccepted sockets get destroyed.
Revert "ax25: Fix std timer socket destroy handling."
[Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
[Bluetooth] Add reset quirk for new Targus and Belkin dongles
[Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
This avoid the pre-mapping of OHCI controller register space, and the
mapping is made only when necessary (OHCI is probed).
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Depending on the order of how resource is defined in the platform
device is not good, use platform_get_{irq,resource} for the IRQ
and memory resources.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. DRCMRxx is no longer recommended, use DRCMR(xx) instead, and
pass DRCMR index by "struct resource" if possible
2. DCSRxx, DDADRxx, DSADRxx, DTADRxx, DCMDxx is never used, use
DCSR(), DDADR(), DSADR(), DTADR(), DCMD() instead
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 135aedc38e, as
requested by Hans Verkuil.
It was a patch for 2.6.28 where the BKL was pushed down from v4l core to
the drivers, not for 2.6.27!
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for Trizeps4 SOM PCMCIA
with ConXS or other baseboards.
with double GPIO-free fixed (sorry!)
replaces 5279/1
Signed-off-by: Jurgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes STATUS_CONF_PENDING usage that called from
iwl4965_mac_config internally after scan completed.
It's called anyway from the mac80211 ieee80211_scan_completed():
if (local->hw_scanning) {
local->hw_scanning = false;
if (ieee80211_hw_config(local))
...
}
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves comment to proper line, it has moved during
code shuffling.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets rx_chain bitmap correctly according hw configuration.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the tx status reporting, fix retry counters (short retries are
virtual collisions, not actual retries). Implement multi-rate retry
support.
This also fixes strong throughput fluctuations with rc80211_pid
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The state field of the rfkill structure was incorrectly initialized to -1, which results in rfkill
issueing a WARN_ON. Fix this by initializing the state field to the proper value as indicated by
the driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the a few lines that went missing in
"p54: 802.11a 5GHz phy support"
Essentially: the rx-code wasn't updated and therefore reported the wrong band,
but more importantly the rate index was off as well, since 802.11a doesn't
allow the "four" 802.11b rates...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables Adaptive Noise Immunity (ANI) on ath9k.
ANI is as algorithm designed to minimize the detrimental
effects of time-varying interferences. This should
help with throughput in noisy environments. To use
ANI we re-enable the MIB interrupt. Since ANI works
on a timer and updates the noise floor we take
advantage of this and also report a non-static noise
floor now to mac80211.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were trying to hold the wrong spinlock due to a typo
on IEEE80211_BAR_CTL_TID_S's definition. We use this to
compute the tid number and then hold this this tid number's
spinlock.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of the cleanup on ath9k -- this was also causing some
annoying compile time warnings.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (33 commits)
V4L/DVB (9103): em28xx: HVR-900 B3C0 - fix audio clicking issue
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
V4L/DVB (9092): gspca: Bad init values for sonixj ov7660.
V4L/DVB (9080): gspca: Add a delay after writing to the sonixj sensors.
V4L/DVB (9075): gspca: Bad check of returned status in i2c_read() spca561.
V4L/DVB (9053): fix buffer overflow in uvc-video
V4L/DVB (9043): S5H1420: Fix size of shadow-array to avoid overflow
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
V4L/DVB (9029): Fix deadlock in demux code
V4L/DVB (8979): sms1xxx: Add new USB product ID for Hauppauge WinTV MiniStick
V4L/DVB (8978): sms1xxx: fix product name for Hauppauge WinTV MiniStick
V4L/DVB (8967): Use correct XC3028L firmware for AMD ATI TV Wonder 600
V4L/DVB (8963): s2255drv field count fix
V4L/DVB (8961): zr36067: Fix RGBR pixel format
V4L/DVB (8960): drivers/media/video/cafe_ccic.c needs mm.h
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
V4L/DVB (8957): zr36067: Restore the default pixel format
V4L/DVB (8955): bttv: Prevent NULL pointer dereference in radio_open
V4L/DVB (8935): em28xx-cards: Remove duplicate entry (EM2800_BOARD_KWORLD_USB2800)
V4L/DVB (8933): gspca: Disable light frquency for zc3xx cs2102 Kokom.
...
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The transfer buffer of an URB will be automatically freed when using
the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will
cause a double free.
Reported-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After a data error, we wait for the NOTBUSY bit to be set so that we can
be sure the data transfer is completely finished. However, when NOTBUSY
is set, the interrupt handler copies the contents of SR into
data_status, overwriting any error bits we may have detected earlier.
To avoid this, initialize data_status to 0 before starting a request, and
don't overwrite it unless it still contains 0.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This adds support for DMA transfers through the generic DMA engine
framework with the DMA slave extensions.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 7.5 MiB/s on fast cards with debugging disabled.
Unfortunately, the driver has been known to lock up from time to time
with DMA enabled, so DMA support is currently optional and marked
EXPERIMENTAL. However, I didn't see any problems while testing 13
different cards (MMC, SD and SDHC of different brands and sizes), so I
suspect the "Initialize BLKR before sending data transfer command" fix
that was posted earlier fixed this as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Atmel MCI controller can drive multiple cards through separate sets
of pins, but only one at a time. This patch adds support for
multiplexing access to the controller so that multiple card slots can be
used as if they were hooked up to separate mmc controllers.
The atmel-mci driver registers each slot as a separate mmc_host. Both
access the same common controller state, but they also have some state
on their own for card detection/write protect handling, and separate
shadows of the MR and SDCR registers.
When one of the slots receives a request from the mmc core, the common
controller state is checked. If it's idle, the request is submitted
immediately. If not, the request is added to a queue. When a request is
done, the queue is checked and if there is a queued request, it is
submitted before the completion callback is called.
This patch also includes a few cleanups and fixes, including a locking
overhaul. I had to change the locking extensively in any case, so I
might as well try to get it right. The driver no longer takes any
irq-safe locks, which may or may not improve the overall system
performance.
This patch also adds a bit of documentation of the internal data
structures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.
Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.
Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Some cards might get upset if we turn off the clock for extended periods
of time. So keep the clock running until the mmc core tells us to turn
it off.
Also, don't reset the controller between each transfer. That was an
attempt to work around earlier bugs, and it never really worked very
well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
With the current system of completed/pending events, things may get
handled in different order depending on which event triggers first. For
example, if the data transfer is complete before the command, the stop
command must be sent after the command is complete, not the data. This
creates a bit of complexity around the stop command.
By having the tasklet go through a sequence of clearly defined states,
things always happen in a certain order even if the events come at
different times, so the stop command can simply be sent when we exit the
"sending data" state because we will never enter that state before the
command has been sent successfully.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Optiarc DVD RW AD-7200A can play audio, but tells it could not.
Signed-off-by: Bodo Eggert <7eggert@gmx.de>
Tested-by: Nick Warne <nick@ukfsn.org>
Received-from: Borislav Petkov <petkovbb@googlemail.com>
[bart: keep "audio" quirks together]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check. So, we must never try
to "split" the PRD for TRM290.
This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=11602.
A more generic fix for drives which cannot autoclose tray will follow.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
[bart: add an extra parentheses for consistency with the rest of kernel code]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Found during the (partial) unregister_netdevice audit that we didn't
have to have :)
It looks like a couple of Sun NIC drivers had unregister_netdevice
when they really meant unregister_netdev.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed audio clicking problem which could be heard when using analog tv or composite input
Signed-off-by: Wiktor Grebla <greblus@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct firmware type to MTS
Correct audio routing for composite/s-video
Add DVB-T detection.
This patch uses the eeprom hash method for detection as the vendor/product
ids are also used for the DIGIVOX_AD. This may be a clone of the same
product. Explanatory text has been added prior to the hask look-up in
anticipation that it may help others.
The following has been tested to work:
Analogue TV (PAL-I)
Composite In
DVB-T (UK Crystal Palace)
USB AUDIO
The following has not been tested but probably works:
S-Video In
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes auto gain functional on 04fc:0561.
Signed-off-by: Shane <gnome42@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a buffer overflow in drivers/media/video/uvc/uvc_ctrl.c:
INFO: 0xf2c5ce08-0xf2c5ce0b. First byte 0xa1 instead of 0xcc
INFO: Allocated in uvc_query_v4l2_ctrl+0x3c/0x239 [uvcvideo] age=13 cpu=1 pid=4975
...
A fixed size 8-byte buffer is allocated, and a variable size field is read
into it; there is no particular bound on the size of the field (it is
dependent on hardware and configuration) and it can overflow [also
verified by inserting printk's.]
The patch attempts to size the buffer to the correctly.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The array size of 'shadow' still needs to be fixed in order to not overflow when reading register 0x00.
Thanks to Oliver Endriss for pointing that out.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Different backends have different input busses (saa7146, flexcop).
To reflect that a config-option to the s5h1420-driver was added which makes
the output mode selectable.
Furthermore the s5h1420-driver is now doing the same i2c-method as it was done
before adding support for other i2c-users.
This patch needs to go into the current release of the kernel, as this driver
is currently broken.
(Thanks to Eberhard Kaltenhaeuser for helping out to debug this issue.)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions dvb_dmxdev_section_callback, dvb_dmxdev_ts_callback,
dvb_dmx_swfilter_packet, dvb_dmx_swfilter_packets, dvb_dmx_swfilter and
dvb_dmx_swfilter_204 may be called from both interrupt and process
context. Therefore they need to be protected by spin_lock_irqsave()
instead of spin_lock().
This fixes a deadlock discovered by lockdep.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2040:5510 is the same hardware as 2040:5500
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AMD ATI TV Wonder 600 has an XC3028L and *not* an XC3028, so we need to
load the proper firmware to prevent the device from overheating.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zr36067 driver is improperly declaring pixel format RGBP twice,
once as "16-bit RGB LE" and once as "16-bit RGB BE". The latter is
actually RGBR. Fix the code to properly map both pixel formats.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sparc32 allmodconfig:
drivers/media/video/cafe_ccic.c: In function 'cafe_setup_siobuf':
drivers/media/video/cafe_ccic.c:1192: error: implicit declaration of function 'PAGE_ALIGN'
drivers/media/video/cafe_ccic.c: At top level:
drivers/media/video/cafe_ccic.c:1430: error: variable 'cafe_v4l_vm_ops' has initializer but incomplete type
drivers/media/video/cafe_ccic.c:1431: error: unknown field 'open' specified in initializer
drivers/media/video/cafe_ccic.c:1431: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1431: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c:1432: error: unknown field 'close' specified in initializer
drivers/media/video/cafe_ccic.c:1433: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1433: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c: In function 'cafe_v4l_mmap':
drivers/media/video/cafe_ccic.c:1444: error: 'VM_WRITE' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1444: error: (Each undeclared identifier is reported only once
drivers/media/video/cafe_ccic.c:1444: error: for each function it appears in.)
drivers/media/video/cafe_ccic.c:1444: error: 'VM_SHARED' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1461: error: 'VM_DONTEXPAND' undeclared (first use in this function)
This build breakage is caused by some header file shuffle in linux-next. But
I suggest that this patch be merged ahead of linux-next to avoid bisection
breakage.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zr36067 driver should return the actual bytes-per-line value when
queried with ioctl VIDIOC_G_FMT, instead of 0. Otherwise user-space
applications can get confused.
Likewise, with ioctl VIDIOC_S_FMT, we are supposed to fill the
bytes-per-line value. And we shouldn't fail if the caller sets the
initial value to something different from 0. This is perfectly valid
for applications to pre-fill this field with the value they expect.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore the default pixel format to YUYV as it used to be before
kernel 2.6.23. It was accidentally changed to BGR3 by commit
603d6f2c8f.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following crash in the bttv driver:
BUG: unable to handle kernel NULL pointer dereference at 000000000000036c
IP: [<ffffffffa037860a>] radio_open+0x3a/0x170 [bttv]
This happens because radio_open assumes that all present bttv devices
have a radio function. If a bttv device without radio and one with
radio are installed on the same system, and the one without radio is
registered first, then radio_open checks for the radio device number
of a bttv device that has no radio function, and this breaks. All we
have to do to fix it is to skip bttv devices without a radio function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CS2102K stop streaming on setlightfreq (50Hz & 60Hz).
Disable it for now until a correct solution is found.
Signed-off-by: Costantino Leandro <le_costantino@pixartargentina.com.ar>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Earlier fixes to get the tuner audio working correctly broke the audio
on the Compro VideoMate H900 cards. This is now fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the ACPI /proc/acpi/wakeup interface set the appropriate wake-up bits
of physical devices corresponding to the ACPI devices and make those bits
be set initially for devices that are enabled to wake up by default. This
is needed to restore the 2.6.26 and earlier behavior for the PCI devices
that were previously handled correctly with the help of the
/proc/acpi/wakeup interface.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check the return value of led_classdev_register and unregister all
registered devices, if registering one device fails. Also the dynamic
memory handling is totally bogus. You can't allocate multiple chunks via
kzalloc() and expect them to be in order later. I wonder how this ever
worked.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Acked-by: Nate Case <ncase@xes-inc.com>
Tested-by: Nate Case <ncase@xes-inc.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On initialization, we first do the ioremap and then register the led devices.
On deinitialization, we do it in reverse order. This prevents someone calling
into the brightness_set functions with an invalid latch_address.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Acked-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tasklet checks RAW.BLOCK twice, and does not check RAW.XFER. This is
obviously wrong, and could theoretically cause the driver to hang.
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Accept zero (the default!) as a per-transfer clock speed override.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't print more information than fits into the string on the
stack. Combine the informational output of qdio to fit into
one line.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix routed RDMA connections to destinations where the next hop is not
the final destination. Use neigh_*() to properly locate neighbor.
Signed-off-by: Bob Sharp <bsharp@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Trace ids 107 and 3 are used twice, fix this to have unique ids for
the erp triggers.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Due to the character of a scheduled work we cannot guarantee the
LUN register to be finished before an initial device tries to use it.
Therefor we have to wait for PENDING_SCSI_WORK flag to be cleared
before proceeding.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The zfcp_erp_thread was using the nolock version of the dbf function.
This resulted in a list access while other tasks could modifying the
list. The symptom was an erp thread running at 100% CPU and never
returning from the dbf function.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In case of an adapter reopen all rports have to be deleted from the
environment. This should only happen for already registered rports
otherwise fc_remote_port_delete is called with a NULL pointer.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Each adapter reopen trigger automatically a scan_port task which
is waiting for the ERP to be finished before further processing.
Since the initial device setup enqueues adapter, port and LUN which
are individual ERP actions, this process would start after
everything is done. Unfortunately the port_reopen requires another
scheduled work to be finished which is queued after the automatic
scan_port -> deadlock !
This fix creates an own work queue for ERP based nameserver requests.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now that we removed the long messages for the bit error threshold
data, put the data in the hba trace. This way, we get a short warning
for the threshold event from the hardware and have the data in the
trace for further analysis.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reduce the size of zfcp data structures by removing unused and
redundant members. scsi_lun is only the mangled version of the
fcp_lun. So, remove the redundant field and use the fcp_lun instead.
Since the queue lock and the pci_batch indicator are only used in the
request queue, move them from the common queue struct to the adapter
struct.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Call the helper function from cio instead looping through all zfcp
adapters.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing the zfcp behaviour from always having the nameserver port
open to an on-demand strategy. This strategy reduces the use of
limited resources like port connections. The patch provides a common
infrastructure which could be used for all WKA ports in future.
Also reduce the number of nameserver lookups by changing the zfcp
behaviour of always querying the nameserver for the corresponding
destination ID of the remote port. If the destination ID has changed
during the reopen process we will be informed and then trigger a
nameserver query on demand.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Remove unused references and declarations, including one instance
of the FC ls_adisc struct that has been defined twice.
- Also remove the flags COMMON_OPENING, COMMON_CLOSING,
ADAPTER_REGISTERED and XPORT_OK that are only set and cleared, but
not checked anywhere.
- Remove the zfcp specific atomic_test_mask makro. Simply use
atomic_read directly instead.
- Remove the zfcp internal sg helper functions and switch the places
where it is still used to call sg_virt directly.
- With the update of the QDIO code, the QDIO data structures no
longer use the volatile type qualifier. Now we can also remove the
volatile qualifiers from the zfcp code.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update the kernel messages in zfcp with input from the message review
and remove some messages that have been identified as redundant.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds a new sysfs attribute queue_full for adapters that records the number
of incidents where a requests could not be submitted due to insufficient
free space on the request queue.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Mon, 2008-09-22 at 14:56 -0700, akpm@linux-foundation.org wrote:
> From: Andrew Morton <akpm@linux-foundation.org>
>
> s390:
>
> drivers/scsi/device_handler/scsi_dh_emc.c: In function 'parse_sp_info_reply':
> drivers/scsi/device_handler/scsi_dh_emc.c:179: warning: comparison is always false due to limited range of data type
>
> because chars are unsigned, I assume.
Fix by making csdev->buffer explicitly an unsigned char and dropping
the < 0 test.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add Dell Powervault storage arrays into device list of rdac device
handler.
Signed-off-by: Yanqing Liu <yanqing_liu@dell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This option was forgotten when the SCSI_QLOGIC_FC driver was removed.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As the driver is only interested in bits 0-9 of the 1st
RSCN-payload word:
rsvd[15:14]RscnEventQualifier[13:10]Fmt[9:8]Domain[7:0]
Area[15:8]Alpa[7:0]
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add additional tightening of residual-count handling (originally
from commit 6acf819002) where the
driver should discard any lower SCSI-status during
firmware/transport residual-count mismatches.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix "occured" spelling errors. Most of these are in comments, which
I wouldn't normally bother with, but a couple are in printks, which
irritate me more. So I just fixed them all at the same time.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To instatiate pre-configured vport entities defined within an
HBA's flash memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Both call-sites are sleeping-capable.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently Firmware does not have counters for input megabytes and
output megabytes, therefore driver counts these values depending
on the status of the scsi command and direction of the command.
The values are exported in the FC_HOST path.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Due to patch building error on my side, we are still passing DID_BUS_BUSY
for commands that are running, when we want to return whatever the caller
of fail_all_commands wanted. This replaces the hardcoded error code with
the value that is passed in.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's already a fc_vport_termintate() call exported by
the transport. This patch adds a symmetric call to the API to allow
an NPIV-capable LLD to instantiate vports sans user intervention.
Additional comments/updates:
Re: scsi_fc_transport.txt
Add a function prototype for fc_vport_terminate similar to what's
done for fc_vport_create
Re: fc_vport_create
I recommend we pass the channel number in fc_vport_create rather
than fixing it at zero.
Also, ids->vport_type should be set to FC_PORTTYPE_NPIV prior to
calling fc_vport_create. The comment is also meaningless.
Added-by and
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
blk_get_request initializes rq->cmd (rq_init does) so the users don't
need to do that.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).
Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition. Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mikulas Patocka