Follow-up patches will extend the registers ioremap and request
to handle SoC-specific quirks on the RSTOUT register. Therefore,
in order to keep the code readable, this commit introduces a special
function for this.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert the imx2_wdt driver to the new watchdog core api.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog driver will be working on IMX2+, Vybrid, LS1, LS2+
platforms, and will be in different endianness mode in those SoCs:
SoCs CPU endian mode WDT endian mode
------------------------------------------------
IMX2+ LE LE
Vybird LE LE
LS1 LE BE
LS2 LE LE
Other possible SoCs:
SoCs CPU endian mode WDT endian mode
------------------------------------------------
Soc1 BE BE
Soc2 BE LE
And also the watchdog's registers will be 32-bits for some versions,
and though it is 16-bits in IMX2+, Vybird and LS+.
Using the regmap APIs, could be more easy to support different
endianness and also more easy to support 32-bits version...
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace clk_enable() and clk_disable() calls with
clk_prepare_enable() and clk_disable_unprepare()
to get ready for the migration to the common clock
framework.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some AR934x based systems, where the frequency of
the AHB bus is relatively high, the built-in watchdog
causes a spurious restart when it gets enabled.
The possible cause of these restarts is that the timeout
value written into the TIMER register does not reaches
the hardware in time.
Add an explicit delay into the ath79_wdt_enable function
to avoid the spurious restarts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: <stable@vger.kernel.org>
This patch removes platform_set_drvdata() which is not used in
the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the prescaler index, rather than its value, to configure the watchdog.
This will prevent a mismatch with the prescaler used to calculate the cycles.
Signed-off-by: Per Gundberg <per.gundberg@icomera.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
When compiling sunxi_defconfig while using C=2, the following error
causes the compilation to fail:
drivers/watchdog/sunxi_wdt.c:60:15: error: constant 0b0001 is not a valid number
Fix it by using hex notation instead of the non-standard binary one
Signed-off-by: Emilio Lopez <emilio@elopez.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exits.
This change was suggested by Thomas Gleixner.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,t,ex;
@@
struct t i = { .remove = ex, };
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to its Kconfig help text, the sbc8360 watchdog driver is
only used on the Axiomtek SBC8360 single-board computer. This piece of
hardware is 32-bit x86 so the driver is useless beyond X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Two bug fixes, one in xattr error path and the other in parsing
major/minor numbers from devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: GPGTools - http://gpgtools.org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=EjHz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.16-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p fixes from Eric Van Hensbergen:
"Two bug fixes, one in xattr error path and the other in parsing
major/minor numbers from devices"
* tag 'for-linus-3.16-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9P: fix return value in v9fs_fid_xattr_set
fs/9p: adjust sscanf parameters accordingly to the variable types
This function is supposed to return true if the new load imbalance is
worse than the old one. It didn't. I can only hope brown paper bags
are in style.
Now things converge much better on both the 4 node and 8 node systems.
I am not sure why this did not seem to impact specjbb performance on the
4 node system, which is the system I have full-time access to.
This bug was introduced recently, with commit e63da03639 ("sched/numa:
Allow task switch if load imbalance improves")
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shrink_inactive_list() used to wait 0.1s to avoid congestion when all
the pages that were isolated from the inactive list were dirty but not
under active writeback. That makes no real sense, and apparently causes
major interactivity issues under some loads since 3.11.
The ostensible reason for it was to wait for kswapd to start writing
pages, but that seems questionable as well, since the congestion wait
code seems to trigger for kswapd itself as well. Also, the logic behind
delaying anything when we haven't actually started writeback is not
clear - it only delays actually starting that writeback.
We'll still trigger the congestion waiting if
(a) the process is kswapd, and we hit pages flagged for immediate
reclaim
(b) the process is not kswapd, and the zone backing dev writeback is
actually congested.
This probably needs to be revisited, but as it is this fixes a reported
regression.
Reported-by: Felipe Contreras <felipe.contreras@gmail.com>
Pinpointed-by: Hillf Danton <dhillf@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
collapse_range and zero_range fallocate functions. In addition,
improve the scalability of adding and remove inodes from the orphan
list.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=C1ZV
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Clean ups and miscellaneous bug fixes, in particular for the new
collapse_range and zero_range fallocate functions. In addition,
improve the scalability of adding and remove inodes from the orphan
list"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (25 commits)
ext4: handle symlink properly with inline_data
ext4: fix wrong assert in ext4_mb_normalize_request()
ext4: fix zeroing of page during writeback
ext4: remove unused local variable "stored" from ext4_readdir(...)
ext4: fix ZERO_RANGE test failure in data journalling
ext4: reduce contention on s_orphan_lock
ext4: use sbi in ext4_orphan_{add|del}()
ext4: use EXT_MAX_BLOCKS in ext4_es_can_be_merged()
ext4: add missing BUFFER_TRACE before ext4_journal_get_write_access
ext4: remove unnecessary double parentheses
ext4: do not destroy ext4_groupinfo_caches if ext4_mb_init() fails
ext4: make local functions static
ext4: fix block bitmap validation when bigalloc, ^flex_bg
ext4: fix block bitmap initialization under sparse_super2
ext4: find the group descriptors on a 1k-block bigalloc,meta_bg filesystem
ext4: avoid unneeded lookup when xattr name is invalid
ext4: fix data integrity sync in ordered mode
ext4: remove obsoleted check
ext4: add a new spinlock i_raw_lock to protect the ext4's raw inode
ext4: fix locking for O_APPEND writes
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlOTY+wACgkQuseO5dulBZXrIgCdFZyXRojufLLKikWEvHjZ3/k5
KsQAnimtcge+62/IX7YwDjWS+xg9Wt3m
=yPrI
-----END PGP SIGNATURE-----
Merge tag 'llvmlinux-for-v3.16' of git://git.linuxfoundation.org/llvmlinux/kernel
Pull LLVM patches from Behan Webster:
"Next set of patches to support compiling the kernel with clang.
They've been soaking in linux-next since the last merge window.
More still in the works for the next merge window..."
* tag 'llvmlinux-for-v3.16' of git://git.linuxfoundation.org/llvmlinux/kernel:
arm, unwind, LLVMLinux: Enable clang to be used for unwinding the stack
ARM: LLVMLinux: Change "extern inline" to "static inline" in glue-cache.h
all: LLVMLinux: Change DWARF flag to support gcc and clang
net: netfilter: LLVMLinux: vlais-netfilter
crypto: LLVMLinux: aligned-attribute.patch
Pull x86 vdso build fix from Peter Anvin:
"This fixes building the vdso code on older Linux systems, and probably
some non-Linux systems"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use <tools/le_byteshift.h> for littleendian access
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
This reverts commit 3e1a878b7c.
It came in very late, and already has one reported failure: Sitsofe
reports that the current tree fails to boot on his EeePC, and bisected
it down to this. Rather than waste time trying to figure out what's
wrong, just revert it.
Reported-by: Sitsofe Wheeler <sitsofe@gmail.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
driver additions and fixes. There are additions to the clock core code
for some of the basic types (e.g. the common divider type has some fixes
and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. ba0fae3 in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=2AAL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux into next
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
Pull exofs raid6 support from Boaz Harrosh:
"These simple patches will enable raid6 using the kernel's raid6_pq
engine for support under exofs and pnfs-objects.
There is nothing needed to do at exofs and pnfs-obj. Just fire your
mkfs.exofs with --raid=6 (that was already supported before) and off
you go as usual. The ORE will pick up the new map and will start
writing two devices of redundancy bits. The patches are so simple
because most of the ORE was already for the general raid case, only a
few bug fixes were needed and the actual wiring into the raid6_pq
engine"
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
ore: Support for raid 6
ore: Remove redundant dev_order(), more cleanups
ore: (trivial) reformat some code
Pull btrfs fix from Chris Mason:
"I had this in my 3.16 merge window queue, but it is small and obvious
enough for 3.15. I cherry-picked and retested against current rc8"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: send, fix corrupted path strings for long paths
Pull x86 fixes from Peter Anvin:
"A significantly larger than I'd like set of patches for just below the
wire. All of these, however, fix real problems.
The one thing that is genuinely scary in here is the change of SMP
initialization, but that *does* fix a confirmed hang when booting
virtual machines.
There is also a patch to actually do the right thing about not
offlining a CPU when there are not enough interrupt vectors available
in the system; the accounting was done incorrectly. The worst case
for that patch is that we fail to offline CPUs when we should (the new
code is strictly more conservative than the old), so is not
particularly risky.
Most of the rest is minor stuff; the EFI patches are all about
exporting correct information to boot loaders and kexec"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: EFI_MIXED should not prohibit loading above 4G
x86/smpboot: Initialize secondary CPU only if master CPU will wait for it
x86/smpboot: Log error on secondary CPU wakeup failure at ERR level
x86: Fix list/memory corruption on CPU hotplug
x86: irq: Get correct available vectors for cpu disable
x86/efi: Do not export efi runtime map in case old map
x86/efi: earlyprintk=efi,keep fix
Patch to prevent warning of a buggy compiler when using clang and
the ARM_UNWIND option.
Clang defines (at least on the current trunk) GNUC, GNUC_MINOR, and
GNUC_PATCHLEVEL to 4, 2, and 1 respectively.
This version of GCC gets flagged as buggy, but it isn't actually an
issue with clang so the patch will do what it did before unless clang
is defined and then it will not report the GCC version as an issue.
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
With compilers which follow the C99 standard (like modern versions of gcc and
clang), "extern inline" does the wrong thing (emits code for an externally
linkable version of the inline function). "static inline" is the correct choice
instead.
Author: Behan Webster <behanw@converseincode.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Both gcc (well, actually gnu as) and clang support the "-Wa,-gdwarf-2" option
(though clang does not support "-Wa,--gdwarf-2"). Since these flags are equivalent
in meaning, this patch uses the one which is better supported across compilers.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Replaced non-standard C use of Variable Length Arrays In Structs (VLAIS) in
xt_repldata.h with a C99 compliant flexible array member and then calculated
offsets to the other struct members. These other members aren't referenced by
name in this code, however this patch maintains the same memory layout and
padding as was previously accomplished using VLAIS.
Had the original structure been ordered differently, with the entries VLA at
the end, then it could have been a flexible member, and this patch would have
been a lot simpler. However since the data stored in this structure is
ultimately exported to userspace, the order of this structure can't be changed.
This patch makes no attempt to change the existing behavior, merely the way in
which the current layout is accomplished using standard C99 constructs. As such
the code can now be compiled with either gcc or clang.
This version of the patch removes the trailing alignment that the VLAIS
structure would allocate in order to simplify the patch.
Author: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Vinícius Tinti <viniciustinti@gmail.com>
__attribute__((aligned)) applies the default alignment for the largest scalar
type for the target ABI. gcc allows it to be applied inline to a defined type.
Clang only allows it to be applied to a type definition (PR11071).
Making it into 2 lines makes it more readable and works with both compilers.
Author: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
commit 7d453eee36 ("x86/efi: Wire up CONFIG_EFI_MIXED") introduced a
regression for the functionality to load kernels above 4G. The relevant
(incorrect) reasoning behind this change can be seen in the commit
message,
"The xloadflags field in the bzImage header is also updated to reflect
that the kernel supports both entry points by setting both of
XLF_EFI_HANDOVER_32 and XLF_EFI_HANDOVER_64 when CONFIG_EFI_MIXED=y.
XLF_CAN_BE_LOADED_ABOVE_4G is disabled so that the kernel text is
guaranteed to be addressable with 32-bits."
This is obviously bogus since 32-bit EFI loaders will never place the
kernel above the 4G mark. So this restriction is entirely unnecessary.
But things are worse than that - since we want to encourage people to
always compile with CONFIG_EFI_MIXED=y so that their kernels work out of
the box for both 32-bit and 64-bit firmware, commit 7d453eee36
effectively disables XLF_CAN_BE_LOADED_ABOVE_4G completely.
Remove the overzealous and superfluous restriction and restore the
XLF_CAN_BE_LOADED_ABOVE_4G functionality.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1402140380-15377-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Merge more updates from Andrew Morton:
- Most of the rest of MM.
This includes "mark remap_file_pages syscall as deprecated" but the
actual "replace remap_file_pages syscall with emulation" is held
back. I guess we'll need to work out when to pull the trigger on
that one.
- various minor cleanups to obscure filesystems
- the drivers/rtc queue
- hfsplus updates
- ufs, hpfs, fatfs, affs, reiserfs
- Documentation/
- signals
- procfs
- cpu hotplug
- lib/idr.c
- rapidio
- sysctl
- ipc updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (171 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Commit 788257d610 ("ufs: remove the BKL") replaced BKL with mutex
protection using functions lock_ufs, unlock_ufs and struct mutex 'mutex'
in sb_info.
Commit b6963327e0 ("ufs: drop lock/unlock super") removed lock/unlock
super and added struct mutex 's_lock' in sb_info.
Those 2 mutexes are generally locked/unlocked at the same time except in
allocation (balloc, ialloc).
This patch merges the 2 mutexes and propagates first commit solution.
It also adds mutex destruction before kfree during ufs_fill_super
failure and ufs_put_super.
[akpm@linux-foundation.org: avoid ifdefs, return -EROFS not -EINVAL]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Cc: "Chen, Jet" <jet.chen@intel.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of commit 799fef0612 ("powerpc: Use generic idle loop"), this
applies to arch_cpu_idle() instead of cpu_idle().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of commit 8dc7c5ecd8 ("cris: Use generic idle loop"), cris no
longer provides cpu_idle().
- On cris-v10, etrax_gpio_wake_up_check() is called from default_idle()
instead of cpu_idle(),
- On cris-v32, etrax_gpio_wake_up_check() is not called from
default_idle(), so remove this (copy-and-paste?) part.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After all architectures were converted to the generic idle framework,
commit d190e8195b ("idle: Remove GENERIC_IDLE_LOOP config switch")
removed the last caller of cpu_idle(). The forward declarations in
header files were forgotten.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Len field is already set to zero, but not the from field which is sent
as 0xfffffffffffffe00. This makes no sense, and may cause confuse
server implementations doing sanity checks (qemu-nbd is an example.)
Signed-off-by: Hani Benhabiles <hani@linux.com>
Cc: Paul Clements <paul.clements@us.sios.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
printk is meant to be used with an associated log level. There are some
instances of printk scattered around the mm code where the log level is
missing. Add a log level and adhere to suggestions by
scripts/checkpatch.pl by moving to the pr_* macros.
Also add the typical pr_fmt definition so that print statements can be
easily traced back to the modules where they occur, correlated one with
another, etc. This will require the removal of some (now redundant)
prefixes on a few print statements.
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes it more likely that patch submitters will CC API/ABI changes to
the linux-api list, and tools like get_maintainer.pl will do so
automatically.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Michael Kerrisk <mtk.man-pages@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace seq_printf where possible. This patch also fixes the following
checkpatch warning "unnecessary whitespace before a quoted newline"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Christine Caulfield <ccaulfie@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace obsolete functions
simple_strtoul/kstrtouint
simple_strtol/kstrtoint
(kstr __must_check requires the right function to be applied)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Christine Caulfield <ccaulfie@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remap_file_pages() system call is used to create a nonlinear
mapping, that is, a mapping in which the pages of the file are mapped
into a nonsequential order in memory. The advantage of using
remap_file_pages() over using repeated calls to mmap(2) is that the
former approach does not require the kernel to create additional VMA
(Virtual Memory Area) data structures.
Supporting of nonlinear mapping requires significant amount of
non-trivial code in kernel virtual memory subsystem including hot paths.
Also to get nonlinear mapping work kernel need a way to distinguish
normal page table entries from entries with file offset (pte_file).
Kernel reserves flag in PTE for this purpose. PTE flags are scarce
resource especially on some CPU architectures. It would be nice to free
up the flag for other usage.
Fortunately, there are not many users of remap_file_pages() in the wild.
It's only known that one enterprise RDBMS implementation uses the
syscall on 32-bit systems to map files bigger than can linearly fit into
32-bit virtual address space. This use-case is not critical anymore
since 64-bit systems are widely available.
The plan is to deprecate the syscall and replace it with an emulation.
The emulation will create new VMAs instead of nonlinear mappings. It's
going to work slower for rare users of remap_file_pages() but ABI is
preserved.
One side effect of emulation (apart from performance) is that user can
hit vm.max_map_count limit more easily due to additional VMAs. See
comment for DEFAULT_MAX_MAP_COUNT for more details on the limit.
[akpm@linux-foundation.org: fix spello]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Armin Rigo <arigo@tunes.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memcg zoneinfo lookup sites have either the page, the zone, or the node
id and zone index, but sites that only have the zone have to look up the
node id and zone index themselves, whereas sites that already have those
two integers use a function for a simple pointer chase.
Provide mem_cgroup_zone_zoneinfo() that takes a zone pointer and let
sites that already have node id and zone index - all for each node, for
each zone iterators - use &memcg->nodeinfo[nid]->zoneinfo[zid].
Rename page_cgroup_zoneinfo() to mem_cgroup_page_zoneinfo() to match.
Signed-off-by: Jianyu Zhan <nasa4836@gmail.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>