Add an soc-camera host livecrop operation to implement live zoom. If
a host driver implements it, it should take care to preserve output
frame format, then live crop doesn't break streaming.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MT9V032 is a parallel wide VGA sensor from Aptina (formerly Micron)
controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports binning and
cropping, and the gain, auto gain, exposure, auto exposure and test
pattern controls.
Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
dma_addr_t may not fit into void* on some architectures. To be safe, make
vb2_dma_contig_cookie() return a pointer to dma_addr_t and dereference it
in vb2_dma_contig_plane_paddr() back to dma_addr_t.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the problem in which a host driver
sets a personalized sizeimage or bytesperline field,
and gets ignored when doing G_FMT.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Rather than guess which driver supports core priority handling, require drivers
that do to explicitly set the V4L2_FL_USE_FH_PRIO flag in video_device.
Updated the core prio handling accordingly and set the flag in the three
drivers that do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device struct has proper ref counting and its release function
will be called when the last user releases it. But no such support was
available for struct v4l2_device. This made it hard to determine when a
USB driver can release the device if it has multiple device nodes.
With one device node it is easy of course, since when the device node is
released, the whole device can be released.
This patch adds refcounting to v4l2_device. When registering device nodes
the v4l2_device refcount will be increased, when releasing device nodes
it will be decreased. The (optional) release function will be called when
the last device node was released.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_fh can now use the core framework support of g/s_priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several drivers need to do something when the first filehandle is opened
or the last filehandle is closed. Most implement some use count mechanism,
but if they use v4l2_fh, then you can also just check if this is the only
filehandle for the device node. A simple helper function can do this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two new functions: v4l2_fh_open allocates and initializes a struct v4l2_fh
based on a struct file pointer and v4l2_fh_release releases and frees a struct
v4l2_fh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Integrate the v4l2_prio_state into the core, ready for use.
One struct v4l2_prio_state is added to v4l2_device and a pointer
to a prio state is added to video_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We are going to move priority handling into the v4l2 core. As a consequence
the v4l2_prio helper functions need to be moved into the core videodev
module as well to prevent circular dependencies.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote used for TerraTec Cinergy T Stick RC.
Keytable from Martin Groszhauser <mgroszhauser@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Martin Groszhauser <mgroszhauser@gmail.com>
Cc: TerraTux <TerraTux@terratec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow the MIPI-CSI data alignment to be defined in the board setup
as it may be different across various camera sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add num_clients field to struct s5p_fimc_isp_info to define exactly
size of clients array which simplifies a bit the sensors management.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some buggy sensors generate corrupt frames when the stream is started.
This new operation return the number of corrupt frames to skip when
starting the stream.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the VIDIOC_SUBDEV_S_CROP and G_CROP ioctls to the
userland API. CROPCAP is not implemented because it's redundant.
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The three new ioctl VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL,
VIDIOC_SUBDEV_G_FRAME_INTERVAL and VIDIOC_SUBDEV_S_FRAME_INTERVAL can be
used to enumerate and configure a subdev's frame rate from userspace.
Two new video::g/s_frame_interval subdev operations are introduced to
support those ioctls. The existing video::g/s_parm operations are
deprecated and shouldn't be used anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a userspace API to get, set and enumerate the media format on a
subdev pad.
The format at the output of a subdev usually depends on the format at
its input(s). The try format operation is thus not suitable for probing
format at individual pads, as it can't modify the device state and thus
can't remember the format tried at the input to compute the output
format.
To fix the problem, pass an extra argument to the get/set format
operations to select the 'try' or 'active' format.
The try format is used when probing the subdev. Setting the try format
must not change the device configuration but can store data for later
reuse. Data storage is provided at the file-handle level so applications
probing the subdev concurently won't interfere with each other.
The active format is used when configuring the subdev. It's identical to
the format handled by the usual get/set operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2_subdev_pad_ops structure for the operations that need to be
performed at the pad level such as format-related operations.
Pad format-related operations use v4l2_mbus_framefmt instead of
v4l2_format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 sub-devices store pad formats and crop settings in the file handle.
To let drivers initialize those settings properly, add an open operation
that is called when the subdev is opened as well as a corresponding
close operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Used for storing subdev information per file handle and hold V4L2 file
handle.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The header defines the v4l2_mbus_framefmt structure which will be used
by the V4L2 subdevs userspace API.
Change the type of the v4l2_mbus_framefmt::code field to __u32, as enum
sizes can differ between different ABIs on the same architectures.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 subdevices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the subdevice, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 devices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the device, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pointer will later be used to register/unregister media entities
when registering/unregistering a v4l2_subdev or a video_device.
With the introduction of media devices, device drivers need to store a
pointer to a driver-specific structure in the device's drvdata.
v4l2_device can't claim ownership of the drvdata anymore.
To maintain compatibility with drivers that rely on v4l2_device storing
a pointer to itself in the device's drvdata, v4l2_device_register() will
keep doing so if the drvdata is NULL.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers often need to associate pipeline objects to entities, and to
take stream state into account when configuring entities and links. The
pipeline API helps drivers manage that information.
When starting streaming, drivers call media_entity_pipeline_start(). The
function marks all entities connected to the given entity through
enabled links, either directly or indirectly, as streaming. Similarly,
when stopping the stream, drivers call media_entity_pipeline_stop().
The media_entity_pipeline_start() function takes a pointer to a media
pipeline and stores it in every entity in the graph. Drivers should
embed the media_pipeline structure in higher-level pipeline structures
and can then access the pipeline through the media_entity structure.
Link configuration will fail with -EBUSY by default if either end of the
link is a streaming entity, unless the link is marked with the
MEDIA_LNK_FL_DYNAMIC flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
setup links.
- MEDIA_IOC_SETUP_LINK: Modify the properties of a given link
The only property that can currently be modified is the ENABLED link
flag to enable/disable a link. Links marked with the IMMUTABLE link flag
can not be enabled or disabled.
Enabling or disabling a link has effects on entities' use count. Those
changes are automatically propagated through the graph.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following two ioctls and implement them at the media device
level to enumerate entities, pads and links.
- MEDIA_IOC_ENUM_ENTITIES: Enumerate entities and their properties
- MEDIA_IOC_ENUM_LINKS: Enumerate all pads and links for a given entity
Entity IDs can be non-contiguous. Userspace applications should
enumerate entities using the MEDIA_ENT_ID_FLAG_NEXT flag. When the flag
is set in the entity ID, the MEDIA_IOC_ENUM_ENTITIES will return the
next entity with an ID bigger than the requested one.
Only forward links that originate at one of the entity's source pads are
returned during the enumeration process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to the wide differences between drivers regarding power management
needs, the media controller does not implement power management.
However, the media_entity structure includes a use_count field that
media drivers can use to track the number of users of every entity for
power management needs.
The use_count field is owned by media drivers and must not be touched by
entity drivers. Access to the field must be protected by the media
device graph_mutex lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add media entity graph traversal. The traversal follows enabled links by
depth first. Traversing graph backwards is prevented by comparing the next
possible entity in the graph with the previous one. Multiply connected
graphs are thus not supported.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As video hardware pipelines become increasingly complex and
configurable, the current hardware description through v4l2 subdevices
reaches its limits. In addition to enumerating and configuring
subdevices, video camera drivers need a way to discover and modify at
runtime how those subdevices are connected. This is done through new
elements called entities, pads and links.
An entity is a basic media hardware building block. It can correspond to
a large variety of logical blocks such as physical hardware devices
(CMOS sensor for instance), logical hardware devices (a building block
in a System-on-Chip image processing pipeline), DMA channels or physical
connectors.
A pad is a connection endpoint through which an entity can interact with
other entities. Data (not restricted to video) produced by an entity
flows from the entity's output to one or more entity inputs. Pads should
not be confused with physical pins at chip boundaries.
A link is a point-to-point oriented connection between two pads, either
on the same entity or on different entities. Data flows from a source
pad to a sink pad.
Links are stored in the source entity. To make backwards graph walk
faster, a copy of all links is also stored in the sink entity. The copy
is known as a backlink and is only used to help graph traversal.
The entity API is made of three functions:
- media_entity_init() initializes an entity. The caller must provide an
array of pads as well as an estimated number of links. The links array
is allocated dynamically and will be reallocated if it grows beyond the
initial estimate.
- media_entity_cleanup() frees resources allocated for an entity. It
must be called during the cleanup phase after unregistering the entity
and before freeing it.
- media_entity_create_link() creates a link between two entities. An
entry in the link array of each entity is allocated and stores pointers
to source and sink pads.
When a media device is unregistered, all its entities are unregistered
automatically.
The code is based on Hans Verkuil <hverkuil@xs4all.nl> initial work.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_device structure abstracts functions common to all kind of
media devices (v4l2, dvb, alsa, ...). It manages media entities and
offers a userspace API to discover and configure the media device
internal topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_devnode structure provides support for registering and
unregistering character devices using a dynamic major number. Reference
counting is handled internally, making device drivers easier to write
without having to solve the open/disconnect race condition issue over
and over again.
The code is based on video/v4l2-dev.c.
[mchehab@redhat.com: Remove linux/smp_lock.h include to not break compilation on bisect]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide v4l2_subdevs with v4l2_event support. Subdev drivers only need very
little to support events.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function isn't small or performance sensitive enough to be inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create a device node named subdevX for every registered subdev.
As the device node is registered before the subdev core::s_config
function is called, return -EGAIN on open until initialization
completes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no reason to require subdevices to implement the core
operations. Remove the check for non-NULL core operations when
initializing the subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vb2_get_plane_payload() gets the bytesused field for a plane, it doesn't
set it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]
[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
This soc_camera driver is for Omnivision's OV9740 sensor. This initial
submission provides support for YUV422 output at 1280x720 (720p), which is
the sensor's native resolution. 640x480 (VGA) is also supported, with
cropping and scaling performed by the sensor's ISP.
This driver is heavily based off of the existing OV9640 driver.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend soc-camera core to also support the videobuf2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a function to calculate the number of samples on the media-bus,
required to retrieve one pixel of a certain format.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, T_STANDBY were used on devices with a separate radio tuner to
mark a tuner that were disabled. With the time, it got newer meanings.
Also, due to a bug at the logic, the driver might incorrectly return
T_STANDBY to userspace.
So, instead of keeping the abuse, just use a boolean for storing
such information.
We can't remove T_STANDBY yet, as this is used on two other drivers. A
latter patch will address its usage outside tuner-core.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add I2C/V4L2 subdev driver for Siliconfile NOON010PC30 CIF camera.
The driver implements basic functionality, i.e. CIF/QCIF/QQCIF
resolution and color format selection, automatic/manual color
balance control. Other functions like cropping, rotation/flip,
exposure etc. can be easily implemented if needed.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ID for NOON010PC30 camera chip and reserve ID range for
Siliconfile sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Port memory-to-memory framework to videobuf2 framework.
Add support for multi-planar Video for Linux 2 API extensions to the
memory-to-memory driver framework.
Based on the original patch written by Pawel Osciak.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a generic file io (read and write) emulator for videobuf2. It uses
MMAP memory type buffers and generic vb2 calls: req_bufs, qbuf and
dqbuf. Video date is being copied from mmap buffers to userspace with
standard copy_to_user() function. To add support for file io the driver
needs to provide an additional callback - read_setup or write_setup. It
should provide the default number of buffers used by emulator and flags.
With these flags one can detemine the style of read() or write()
emulation. By default 'streaming' style is used. With
VB2_FILEIO_READ_ONCE flag one can select 'one shot' mode for read()
emulator. With VB2_FILEIO_WRITE_IMMEDIATE flag one can select immediate
conversion of write calls to qbuf for write() emulator, so the vb2 will
not wait until each buffer is filled completely before queueing it to
the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA scatter/gather allocator and handling
routines for videobuf2.
For mmap operation mode it is implemented on top of
alloc_page + sg_set_page/_free_page.
For userptr operation mode it is implemented on top of
get_user_pages + sg_set_page/put_page.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA coherent memory allocator and handling
routines for videobuf2, implemented on top of dma_alloc_coherent() call.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of contiguous virtual memory allocator and handling
routines for videobuf2, implemented on top of vmalloc()/vfree() calls.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 is a Video for Linux 2 API-compatible driver framework for
multimedia devices. It acts as an intermediate layer between userspace
applications and device drivers. It also provides low-level, modular
memory management functions for drivers.
Videobuf2 eases driver development, reduces drivers' code size and aids in
proper and consistent implementation of V4L2 API in drivers.
Videobuf2 memory management backend is fully modular. This allows custom
memory management routines for devices and platforms with non-standard
memory management requirements to be plugged in, without changing the
high-level buffer management functions and API.
The framework provides:
- implementations of streaming I/O V4L2 ioctls and file operations
- high-level video buffer, video queue and state management functions
- video buffer memory allocation and management
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adding support for Technisat's new USB2.0 DVB-S/S2 receiver
device. The development was sponsored by Technisat.
The Green led is toggle depending on the frontend-state. The Red LED is turned
on all the time.
The MAC address reading from the EEPROM along with the
LRC-method to check whether its valid.
Support for the IR-receiver of the Technisat USB2 box. The keys of
small, black remote-control are built-in, repeated key behaviour are
simulated.
The i2c-mutex of the dvb-usb-structure is used as a general mutex for
USB requests, as there are 3 threads racing for atomic requests
consisting of multiple usb-requests.
A module option is there which disables the toggling of LEDs by the
driver on certain triggers. Useful when being used in a "dark"
environment.
[mchehab@redhat.com: Fix merge conflicts with RC renaming patches]
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The later makes extensive use of structures defined in the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:
MS_TO_NS - milliseconds to nanoseconds
MS_TO_US - milliseconds to microseconds
US_TO_NS - microseconds to nanoseconds
Reported-by: David Härdeman <david@hardeman.nu>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Renamed has_new to is_new.
Drivers can use the is_new field to determine if a new value was specified
for a control. The v4l2_ctrl_handler_setup() must always set this to 1 since
the setup has to force a full update of all controls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some subdevs need to call into the board code after they are registered
and have a valid struct v4l2_device pointer. The s_config op was abused
for this, but now that it is removed we need a cleaner way of solving this.
So this patch adds a struct with internal ops that the v4l2 core can call.
Currently only two ops exist: register and unregister. Subdevs can implement
these to call the board code and pass it the v4l2_device pointer, which the
board code can then use to get access to the struct that embeds the
v4l2_device.
It is expected that in the future open and close ops will also be added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core.s_config op was meant for legacy drivers that needed to work with old
pre-2.6.26 kernels. This is no longer relevant. Unfortunately, this op was
incorrectly called from several drivers.
Replace those occurences with proper i2c_board_info structs and call
v4l2_i2c_new_subdev_board.
After these changes v4l2_i2c_new_subdev_cfg() was no longer used, so remove
that function as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert saa7146 to use core-assisted locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that cx88 and ivtv use wm8775 on some different modes. The
patch that added support for a board with wm8775 broke ivtv boards with
this device. As we're too close to release 2.6.37, let's just revert
it.
Reported-by: Andy Walls <awalls@md.metrocast.net>
Reported-by: Eric Sharkey <eric@lisaneric.org>
Reported-by: Auric <auric@aanet.com.au>
Reported by: David Gesswein <djg@pdp8online.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In certain machines, camera devices are supplied directly
by a number of regulators. This patch add the ability to drive
these regulators directly by the soc_camera driver.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents checkpatch warnings generated when defining
'static const char *foo[]' arrays. It makes sense to use
const char * const * anyway since the pointers in the array
are indeed const.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bt819.h from ioctl-number.txt and make a note in the header
that these ioctls are for internal use only.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The naming of the media/rds.h header suggested that it was a generic
RDS header, when in fact it is just a saa6588 module API that is
internal to the kernel.
Rename the header and the struct and defines in it to make this clear.
Also removed the header include in radio-si470x.h (not used anymore)
and from ioctl-number.txt (it's internal to the kernel and never called
from userspace).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no sense on keeping it on 2.6.38, as nobody is using it
anymore, at the kernel tree, and installing it at the userspace
API.
As two deprecated drivers still need it, move it to their internal
directories.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some minor comments etc which are leftover from the old naming scheme.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote keytables had different names all over the place. Part of the fault
is due to a bad naming when rc subsystem was created, but there were lots
of old names that were still here.
Use a common standard for everything.
Patch generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_codes_,rc_map_,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_key_map,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_map_table_size,rc_map_size,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The struct that describes a rc mapping had an weird and long name.
We should properly name it, to make easier for developers to work
with it, and to avoid confusion.
Basically, generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode_table,rc_map,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_tab,rc_map,g <$i >a && mv a $i; done
(and manually fixed where needed)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h
To be consistent with the other changes.
No functional change on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the timberdale video-in driver.
The video IP of timberdale delivers the video data via DMA.
The driver uses the DMA api to handle DMA transfers, and make use
of the V4L2 video buffers to handle buffers against user space.
If available the driver uses an encoder to get/set the video standard
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several fields on rc_dev that drivers can benefit. Allow drivers
to pass it as a parameter to the driver.
For now, the rc_dev parameter is optional. If drivers don't pass it, create
them internally. However, the best is to create rc_dev inside the drivers,
in order to fill other fields, like open(), close(), driver_name, etc.
So, a latter patch making it mandatory and changing the caller drivers is
welcome.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.
This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.
The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()
[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: this patch were originally bundled with some renaming
stuff and with the file merges, as seen at:
https://patchwork.kernel.org/patch/291092/.
Instead of using the original approach, I wrote the rename patches and the
code merge as separate changes, then applied the difference on this patch.
This way, it is easier to see the real changes at the code, and will be easier
to merge upstream, especially if some conflict rises on the renaming patches]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88 only depends on VIDEO_IR because it needs ir_extract_bits().
Move that function to ir-core.h and make it inline.
Lots of drivers had dependencies on VIDEO_IR when they really
wanted IR_CORE.
The only remaining drivers to depend on VIDEO_IR are bt8xx and
saa7134 (ir_rc5_timer_end is the only function exported by
ir-functions).
Rename VIDEO_IR -> IR_LEGACY to give a hint to anyone writing or
converting drivers to IR_CORE that they do not want a dependency
on IR_LEGACY.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the remaining usages of the ir_input_nokey() and
ir_input_keydown() functions provided by drivers/media/IR/ir-functions.c
by using the corresponding functionality in ir-core instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the cx88 driver (for sampling hw) to use the
decoders provided by ir-core instead of the separate ones provided
by ir-functions (and gets rid of those).
The value for MO_DDS_IO had a comment saying it corresponded to
a 4kHz samplerate. That comment was unfortunately misleading. The
actual samplerate was something like 3250Hz.
The current value has been derived by analyzing the elapsed time
between interrupts for different values (knowing that each interrupt
corresponds to 32 samples).
Thanks to Mariusz Bialonczyk <manio@skyboo.net> for testing my patches
(about one a day for two weeks!) on actual hardware.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the driver to use regulator framework instead of set_power callback.
This with gpio_reset platform data provide cleaner way to manage chip VIO,
VDD and reset signal inside the driver.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Drivers should append their name on exported symbols, to avoid
conflicts with allyesconfig:
drivers/staging/built-in.o: In function `format_by_fourcc':
/home/v4l/work_trees/linus/drivers/staging/cx25821/cx25821-video.c:96: multiple definition of `format_by_fourcc'
drivers/media/built-in.o:/home/v4l/work_trees/linus/drivers/media/common/saa7146_video.c:88: first defined here
Let's rename both occurences with a small shellscript:
for i in drivers/staging/cx25821/*.[ch]; do sed s,format_by_fourcc,cx25821_format_by_fourcc,g <$i >a && mv a $i; done
for i in drivers/media/common/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
for i in include/media/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL replacement mutex had some serious performance side-effects on
V4L drivers. It is replaced by a better heuristic that works around the
worst of the side-effects.
Read the v4l2-dev.c comments for the whole sorry story. This is a
temporary measure only until we can convert all v4l drivers to use
unlocked_ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The argument isn't used anymore by the functions, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Lawrence Rust <lawrence@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the sh_vou
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for the video capture port on VIA integrated chipsets. This
version has a remaining OLPCism or two and expects to be talking to an
ov7670; those can be improved as the need arises.
This work was supported by the One Laptop Per Child project.
Thanks to Laurent Pinchart for a number of useful comments.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new event types for timeout & carrier report
Move timeout handling from ir_raw_event_store_with_filter to
ir-lirc-codec, where it is really needed.
Now lirc bridge ensures proper gap handling.
Extend lirc bridge for carrier & timeout reports
Note: all new ir_raw_event variables now should be initialized
like that: DEFINE_IR_RAW_EVENT(ev);
To clean an existing event, use init_ir_raw_event(&ev);
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch add support of TwinHan 1027 DVB-S card.
Refreshed version of https://patchwork.kernel.org/patch/79753/ patch.
(adapted for the new IR system), still works.
DVB-S support come from a patch originally authored by
Manu Abraham (abraham.manu@gmail.com).
IR Port support were added by Sergey.
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an I2C/v4l2-subdev driver for Siliconfile SR030PC30 VGA
camera sensor with Image Signal Processor. SR030PC30 is
the low resolution camera sensor on Samsung Aquila boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a video device driver per each FIMC entity to support
the camera capture input mode. Video capture node is registered
only if CCD sensor data is provided through driver's platfrom data
and board setup code.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides a V4L2 SoC Camera driver for OV6650 camera sensor, found
on OMAP1 SoC based Amstrad Delta videophone.
Since I have no experience with camera sensors, and the sensor documentation I
was able to find was not very comprehensive, I left most settings at their
default (reset) values, except for:
- those required for proper mediabus parameters and picture geometry and
format setup,
- those used by controls.
Resulting picture quality may be far from perfect, but better than nothing.
In order to be able to get / set the sensor frame rate from userspace, I
decided to provide two not yet SoC camera supported operations, g_parm and
s_parm. These can be used after applying patch 4/6 from this series,
"SoC Camera: add support for g_parm / s_parm operations".
Created and tested against linux-2.6.36-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a V4L2 driver for TI OMAP1 SoC camera interface.
Both videobuf-dma versions are supported, contig and sg, selectable with a
module option. The former uses less processing power, but often fails to
allocate contignuous buffer memory. The latter is free of this problem, but
generates tens of DMA interrupts per frame. If contig memory allocation ever
fails, the driver falls back to sg automatically on next open, but still can
be switched back to contig manually. Both paths work stable for me, even
under heavy load, on my OMAP1510 based Amstrad Delta videophone, that is the
oldest, least powerfull OMAP1 implementation.
The interface generally works in pass-through mode. Since input data byte
endianess can be swapped, it provides up to two v4l2 pixel formats per each of
several soc_mbus formats that have their swapped endian counterparts.
Boards using this driver can provide it with the following platform data:
- if and what freqency clock is expected by an on-board camera sensor,
- what is the maximum pixel clock that should be accepted from the sensor,
- what is the polarity of the sensor provided pixel clock,
- if the interface GPIO line is connected to a sensor reset/powerdown input
and what is the input polarity.
Created and tested against linux-2.6.36-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
>From Joris van Rantwijk <jorispubl@xs4all.nl>:
I tested lirc_serial and found that it works fine.
Except the LIRC ioctls do not work in my 64-bit-kernel/32-bit-user
setup. I added compat_ioctl entries in the drivers to fix this.
While doing so, I noticed inconsistencies in the argument type of
the LIRC ioctls. All ioctls are declared in lirc.h as having argument
type __u32, however there are a few places where the driver calls
get_user/put_user with an unsigned long argument.
The patch below changes lirc_dev and lirc_serial to use __u32 for all
ioctl arguments, and adds compat_ioctl entries.
It should probably also be done in the other low-level drivers,
but I don't have hardware to test those.
I've dropped the .compat_ioctl addition from Joris' original patch,
as I swear the non-compat definition should now work for both 32-bit
and 64-bit userspace. Technically, I think we still need/want a
in getting a reply to you).
Reported-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h. Initial keytable was from
Jose Alberto Reguero <jareguero@telefonica.net> and
Felipe Morales Moreno <felipe.morales.moreno@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Digittrade DVB-T USB Stick remote controller.
Imported from af9015.h. Initial keytable was from Alain Kalker <miki@dds.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h.
Initial keytable was from Marc Schneider <macke@macke.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MSI DIGIVOX mini III remote controller. Uses NEC extended 0x61d6.
This remote seems to be same as rc-kworld-315u.c. Anyhow, add new remote
since rc-kworld-315u.c lacks NEC extended address byte.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct file_operations was made const in the drivers, but not in struct
lirc_driver:
drivers/staging/lirc/lirc_it87.c:365: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_parallel.c:571: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_serial.c:1073: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_sir.c:482: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_zilog.c:1284: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is an internal API and belongs in v4l2-common.h, not
videodev.h. The return pointer and probe argument should be const as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multiple user-space application instances can open the same video device, but
it only makes sense for one of them to manage the videobuffer queue and set
video format of the device. Restrict soc-camera respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_waiton() must unlock and relock ext_lock if it has to wait.
For that to happen it needs the videobuf_queue pointer.
Don't attempt to unlock/relock q->ext_lock unless it was locked in the
first place.
vb->state has to be protected by a spinlock to be safe.
This patch is based on code from Mauro Carvalho Chehab <mchehab@redhat.com>.
[mchehab@redhat.com: add extra argument to a few missing places]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently videobuf uses the vb_lock mutex to lock its data structures.
But this locking will (optionally) move into the v4l2 core, which means
that in that case vb_lock shouldn't be used since the external lock is already
held.
Prepare for this by adding a pointer to such an external mutex and
don't lock if that pointer is set.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers can optionally set a pointer to a mutex in struct video_device.
The core will use that to lock before calling open, read, write, unlocked_ioctl,
poll, mmap or release.
Updated the documentation as well and ensure that v4l2-event knows about the
lock: it will unlock it before doing a blocking wait on an event and relock it
afterwards.
Ensure that the 'video_is_registered' check is done when the lock is held:
a typical disconnect will take the lock as well before unregistering the
device nodes, so to prevent race conditions the video_is_registered check
should also be done with the lock held.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon driver currently reimplements its own version of ir_keyup
(along with key release timer functionality also already present in the
core IR code). A follow-up imon patch will make use of ir_keyup and the
IR stack's key release code.
Trivial extraction from David Härdeman's pending rc-core merge and
device interface abstraction patchset to facilitate merging a patch
based on his imon input dev split patch ahead of the larger churn, which
is slated for post-2.6.37-rc1 (after Dmitry's large keycode patches are
merged in mainline).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason for keeping I2C_HW_SAA7134 is to allow setting a
per-device polling interval. Just move this info to the platform
data, allowing drivers to change it per device, where needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The include/media/v4l2-i2c-drv.h header was used to be able to compile drivers
in the v4l-dvb hg repository for legacy kernels (mainly pre-2.6.26) without
creating an #ifdef mess.
The hg repository dropped support for kernels < 2.6.26 so we can remove this
header. All i2c drivers that used it have now been converted to use proper
i2c code. The header was a hack, but it did its job well. So I would call
this an honorable removal. :-)
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vtx (aka videotext aka teletext) API from the v4l2 core.
This API was scheduled for removal in kernel 2.6.35.
The vtx device nodes have been superseded by vbi device nodes
for many years. No applications exist that use the vtx support.
Of the two i2c drivers that actually support this API the saa5249
has been impossible to use for a year now and no known hardware
that supports this device exists. The saa5246a is theoretically
supported by the old mxb boards, but it never actually worked.
In summary: there is no hardware that can use this API and there
are no applications actually implementing this API.
The vtx support still reserves minors 192-223 and we would really
like to reuse those for upcoming new functionality. In the unlikely
event that new hardware appears that wants to use the functionality
provided by the vtx API, then that functionality should be build
around the sliced VBI API instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The existing priv field stores subdev private data owned by the subdev
driver. Host (bridge) drivers might need to store per-subdev
host-specific data, such as a pointer to platform data.
Add a v4l2_subdev host_priv field to store host-specific data, and
rename the existing priv field to dev_priv.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"sd" and "err" are too common names to be used in macros for local variables.
Prefix them with an underscore to avoid name clashing.
[mchehab@redhat.com: whitespace cleanups]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes in-kernel decoding with the stock Streamzap PC Remote
work out of the box. There are quite a few things going on in this
patch, all related to getting this working:
1) I had to enable reporting of a long space at the end of each signal,
or I had weird buffering and keybounce issues.
2) The keymap has been reworked slightly to match actual decoded values,
the first edition was missing the pre-data bits present in the lirc
config file for this remote.
3) There's a whole new decoder included, specifically for the
not-quite-RC5 15-bit protocol variant used by the Streamzap PC
Remote. The decoder, while usable with other recievers (tested with
an mceusb receiver), will only be loaded by the streamzap driver, as
its likely not of use in almost all other situations. This can be
revisited if/when all keytable loading (and disabling of unneeded
protocol decoder engines) is moved to userspace, but for now, I think
this makes the most sense.
Note that I did try to enable handling the streamzap RC5-ish protocol in
the current RC5 decoder, but there's no particularly easy way to tell if
its 14-bit RC5 or 15-bit Streamzap until we see bit 14, and even then,
in testing an attempted decoder merge, only 2/3 of the keys were
properly recognized as being the 15-bit variant and decoded correctly,
the rest were close enough to compliant with 14-bit that they were
decoded as such (but they have overlap with one another, and thus we
can't just shrug and use the 14-bit decoded values).
Also of note in this patch is the removal of the streamzap driver's
internal delay buffer. Per discussion w/Christoph, it shouldn't be
needed by lirc any longer anyway, and it doesn't seem to make any
difference to the in-kernel decoder engine. That being the case, I'm
yanking it all out, as it greatly simplifies the driver code.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These have now all been replaced by enum/try/s/g_mbus_fmt.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a nasty memory corruption bug when using userptr I/O.
The function videobuf_pages_to_sg() sets up the scatter-gather list for the
DMA transfer to the userspace pages. The first transfer is setup correctly
(the size is set to PAGE_SIZE - offset), but all other transfers have size
PAGE_SIZE. This is wrong for the last transfer which may be less than PAGE_SIZE.
Most, if not all, drivers will program the boards DMA engine correctly, i.e.
even though the size in the last sg element is wrong, they will do their
own size calculations and make sure the right amount is DMA-ed, and so seemingly
prevent memory corruption.
However, behind the scenes the dynamic DMA mapping support (in lib/swiotlb.c)
may create bounce buffers if the memory pages are not in DMA-able memory.
This happens for example on a 64-bit linux with a board that only supports
32-bit DMA.
These bounce buffers DO use the information in the sg list to determine the
size. So while the DMA engine transfers the correct amount of data, when the
data is 'bounced' back too much is copied, causing buffer overwrites.
The fix is simple: calculate and set the correct size for the last sg list
element.
Signed-off-by: Hans Verkuil <hans.verkuil@tandberg.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch the code to use new style of getkeycode and setkeycode
methods to allow retrieving and setting keycodes not only by
their scancodes but also by index.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since this module is also used by drivers that are not yet converted, the old
and new code have to co-exist.
The source is split into three parts: a common part at the top, which is used
by both old and new code, then the old code followed by the new control
framework implementation. This new code is much more readable (and shorter!)
than the original code.
Once all bridge drivers that use this are converted the old code can be
deleted.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 used a private control CX25840_CID_ENABLE_PVR150_WORKAROUND
to be told whether to enable a workaround for certain pvr150 cards.
This is really config data that it needs to get at load time.
Implemented this in cx25840 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new framework to handle controls which makes life for driver
developers much easier.
Note that this patch moves some of the control support that used to be in
v4l2-common.c to v4l2-ctrls.c. The tables were copied unchanged. The body
of v4l2_ctrl_query_fill() was copied to a new v4l2_ctrl_fill() function
in v4l2-ctrls.c. This new function doesn't use the v4l2_queryctrl
struct anymore, which makes it more general.
The remainder of v4l2-ctrls.c is all new. Highlights include:
- No need to implement VIDIOC_QUERYCTRL, QUERYMENU, S_CTRL, G_CTRL,
S_EXT_CTRLS, G_EXT_CTRLS or TRY_EXT_CTRLS in either bridge drivers
or subdevs. New wrapper functions are provided that can just be plugged in.
Once everything has been converted these wrapper functions can be removed as well.
- When subdevices are added their controls can be automatically merged
with the bridge driver's controls.
- Most drivers just need to implement s_ctrl to set the controls.
The framework handles the locking and tries to be as 'atomic' as possible.
- Ready for the subdev device nodes: the same mechanism applies to subdevs
and their device nodes as well. Sub-device drivers can make controls
local, preventing them from being merged with bridge drivers.
- Takes care of backwards compatibility handling of VIDIOC_S_CTRL and
VIDIOC_G_CTRL. Handling of V4L2_CID_PRIVATE_BASE is fully transparent.
CTRL_CLASS controls are automatically added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
LIRC: add new IOCTL that enables learning mode (wide band receiver)
Still missing features: carrier report & timeout reports.
Will need to pack these into ir_raw_event
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ir input devices have small buffer, and interrupt the host
each time it is full (or half full)
Add a helper that automaticly handles timeouts, and also
automaticly merges samples of same time (space-space)
Such samples might be placed by hardware because size of
sample in the buffer is small (a byte for example).
Also remove constness from ir_dev_props, because it now contains timeout
settings that driver might want to change
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, ir device registration fails if keymap requested by driver is not found.
Fix that by always compiling in the empty keymap, and using it as a failback.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ports lirc_streamzap.c over to ir-core in-place, to be followed by
a patch moving the driver over to drivers/media/IR/streamzap.c and
enabling the proper Kconfig bits.
Presently, the in-kernel keymap doesn't work, as the stock Streamzap
remote uses an RC-5-like, but not-quite-RC-5 protocol, which the
in-kernel RC-5 decoder doesn't cope with. The remote can be used right
now with the lirc bridge driver though, and other remotes (at least an
RC-6(A) MCE remote) work perfectly with the driver.
I'll take a look at making the existing RC-5 decoder cope with this odd
duck, possibly implement another standalone decoder engine, or just
throw up my hands and say "meh, use lirc"... But the driver itself
should be perfectly sound.
Remaining items on the streamzap TODO list:
- add LIRC_SET_REC_TIMEOUT-alike support
- add LIRC_GET_M{AX,IN}_TIMEOUT-alike support
- add LIRC_GET_REC_RESOLUTION-alike support
All of the above should be trivial to add. There are patches pending to
add this support to ir-core from Maxim Levitsky, and I'll take care of
these once his patches get integrated. None of them are currently
essential though.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources. Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block. This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters. This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a method to v4l2_sudev_core_ops to allow bridge drivers to
manage what signal pads/functions are routed out to multiplexed IO pins on a
pin by pin basis. The interface also allows specifying initial output settings
for pins and disabling an IO pin altogether.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big keytable with 2 protocols inside, break it
into two separate tables, being one for NEC and another for RC-5 variants,
and properly identify what variant should be used at the boards entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These formats belong to the standard format set, defined by the MIPI CSI-2
specification.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lirc userspace needs all the current ioctls defined, and we need to
put the header files in places out-of-tree and/or staging lirc drivers
(which I plan to prep soon) can easily build with. I've actually tested this
in a tree w/all the lirc drivers queued up to be submitted for staging. I'm
also reasonably sure that Andy Walls is going to need most of the ioctls
anyway for his cx23888 IR driver work.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_dmabuf and videobuf_vmalloc_memory fields have a vmalloc
field to store the kernel virtual address of vmalloc'ed buffers. Rename
the field to vaddr.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fields are assigned but never used, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those functions are only called inside videobuf-dma-sg.c, make them
static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of creating dirty wrappers around videobuf_dma_map/unmap that
create a dummy videobuf_queue structure, modify videobuf_dma_map/unmap
to take a device pointer argument and use it directly. The
videobuf_sg_dma_map/unmap then become unused and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These functions allocate videobuf_buffer structures only. Renaming in order
to prevent confusion with functions allocating actual video buffer memory.
Rename the functions in videobuf-core.h videobuf-dma-sg.c as well.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
incoming IR buffer now an int pointer, and not fed from userspace
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v2: copy of buffer data from userspace done inside this plugin/driver,
keeping the actual drivers minimal, and more flexible in what we can
deliver to them later on (they may be fed from within kernelspace later
on, by an in-kernel IR encoder).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v2: currently unused ioctls are included, but #if 0'd out
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Partially convert drivers/media/video/ir-kbd-i2c.c to
not use ir-functions.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the RC6 keymap for the Windows Media Center Edition remotes
that come bundled with MCE/eHome Infrared Remote transceivers. Tested
with 3 different variants of the remote, but its possible there are
still some additional keys missing, but its simple enough to add them
in later...
This patch also adds an IR_TYPE_ALL convenience macro to make life
easier for receivers that support all IR protocols.
v2: fix an erroneous comment that referred to imon devices
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for one more remote control type for Avermedia
M135A (model RM-K6), shipped with Positivo machines.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for Avermedia M733A. The original version for
linux 2.6.31 was sent to me from Avermedia, original author is unknown.
I ported it to current kernels, expanded and fixed key code handling for
RM-K6 remote control, and added an additional pci id also supported.
[mchehab@redhat.com: make checkpatch.pl happier]
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
enum_mbus_fmt received an index argument that was defined as an int instead
of an unsigned int. This is now fixed. This had the knock-on effect that the
index argument in the callback get_formats in soc_camera.h also had to be
changed to unsigned int.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The op enum_dv_preset was missing in this header but is needed by subdev
drivers with DV functionality.
Signed-off-by: Mats Randgaard <mats.randgaard@tandberg.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_prio_init/open/close returned an int when in fact they would
always return 0. Make these void functions.
v4l2_prio_close and v4l2_prio_check pass an enum v4l2_priority as a
pointer for no good reason. Replace with a normal enum v4l2_priority
argument.
These changes will simplify the work of moving priority handling into
the v4l core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently raw and sliced vbi is setup using the video g/s_fmt ops.
However, we want to split off the vbi formatting into separate ops
so the first step is to create those new ops.
The next step will be to convert subdev drivers and bridge drivers
to use the new ops. And in the final step we can start converting
the video g/s_fmt ops to the new (and more appropriate) mediabus
format ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only a relatively small number of video receivers and transmitters actually
support VBI. So start moving the vbi specific ops to an ops struct of their
own.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While analyzing one of the videobuf patches, I noticed that
videobuf_dma_sync is only used internally inside videobuf-dma-sg.
So, let's remove this function, merging the code at __videobuf_dma_sync()
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pulse-distance is not a protocol, it is a line coding (used by some protocols,
like NEC). Looking at the uses of IR_TYPE_PD, the real protocol seems to be
NEC in all cases (drivers/media/video/cx88/cx88-input.c is the only user).
So, remove IR_TYPE_PD while it is still easy to do so.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for event handling to do_ioctl.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add event handling backend to V4L2. The backend handles event subscription
and delivery to file handles. Event subscriptions are based on file handle.
Events may be delivered to all subscribed file handles on a device
independent of where they originate from.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a list of v4l2_fh structures to every video_device.
It allows using file handle related information in V4L2. The event interface
is one example of such use.
The use of v4l2_fh is not mandatory for drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A mem-to-mem device is a device that uses memory buffers passed by
userspace applications for both their source and destination data. This
is different from existing drivers, which utilize memory buffers for either
input or output, but not both.
In terms of V4L2 such a device would be both of OUTPUT and CAPTURE type.
Examples of such devices would be: image 'resizers', 'rotators',
'colorspace converters', etc.
This patch adds a separate Kconfig sub-menu for mem-to-mem devices as well.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AK8814 only differs from AK8813 by included Macrovision Copy Protection
function. This patch adds a driver for AK8813 and AK8814 I2C PAL/NTSC TV
encoders.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of SuperH Mobile SoCs, including sh7724, include a Video Output Unit.
This patch adds a video (V4L2) output driver for it. The driver uses v4l2-subdev
and mediabus APIs to interface to TV encoders.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mmap_mapper should operate on a buffer, not on a complete queue. So let
the videobuf-core find the correct buffer instead of duplicating that
code in each mmap_mapper implementation.
The dma-sg implementation has backwards compatibility code for handling
the V4L1_COMPAT layer. This code is now under the v4L1_COMPAT config option.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_copy_to_user and copy_stream ops are almost identical for all
videobuf memtype variants. All that is needed is to use the new vaddr
op and these functions can be moved into the core, ensuring we have just
one single implementation instead of three.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ths function returns the virtual kernel address of the buffer and has
nothing to do with allocation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the .vmalloc op in struct videobuf_qtype_ops to .vaddr. This op returns
the virtual kernel address of a buffer. vaddr is a lot less confusing than
vmalloc since this callback does do any allocations.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_alloc() returned a void *. Change to struct videobuf_buffer *
to get better type checking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the mmap_free callback from struct videobuf_qtype_ops.
All implementations of this callback do the same trivial check: return
-EBUSY if any buffer is mmapped. That can also be tested in the
videobuf core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mmap callback in struct videobuf_qtype_ops is never used.
Remove.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a Sony12/15/20 decoder to ir-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements the agreed upon 1:31 integer encoded pulse/duration
struct for ir-core raw decoders. All decoders have been tested after the
change. Comments are welcome.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the keymaps for the hardware decode scancodes imon
devices create for their native imon pad (and mini) remotes,
and the hardware scancodes generated by the imon devices when
used with an rc6 windows media center ed. remote.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon driver I've previously submitted and have been porting to
use ir-core needs to use ir_g_keycode_from_table, as ir_keydown is
not sufficient, due to these things having really oddball hardware
decoders in them. This just moves the function declaration from
ir-core-priv.h over to ir-core.h.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds an RC6 decoder (modes 0 and 6A) to ir-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-core.h has the kABI to be used by the bridge drivers, when needing to register
IR protocols and pass IR events. However, the same file also contains IR subsystem
internal calls, meant to be used inside ir-core and between ir-core and the raw
decoders.
Better to move those functions to an internal header, for some reasons:
1) Header will be a little more cleaner;
2) It avoids the need of recompile everything (bridge/hardware drivers, etc),
just because a new decoder were added, or some other internal change were needed;
3) Better organize the ir-core API, splitting the functions that are internal to
IR core and the ancillary drivers (decoders, lirc_dev) from the features that
should be exported to IR subsystem clients.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-raw-event.c is currently written with the assumption
that all "raw" hardware will generate events only on state change (i.e.
when a pulse or space starts).
However, some hardware (like mceusb, probably the most popular IR receiver
out there) only generates duration data (and that data is buffered so using
any kind of timing on the data is futile).
Furthermore, using signed int's to represent pulse/space durations is a
well-known approach when writing ir decoders.
With this patch:
- s64 int's are used to represent pulse/space durations in ns
- a workqueue is used to decode the ir protocols outside of interrupt context
- #defines are added to make decoders clearer
- decoder reset is implemented by passing a zero duration to the kfifo queue
and decoders are updated accordingly
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices have in-hardware Remote Controller decoder, while others
need a software decoder to get the IR code. As each software decoder
can be enabled/disabled individually, allowing multiple protocol
decoding capability.
On the other hand, hardware decoders have a limited protocol
support, often being able of decoding just one protocol each time.
So, each type needs a different set of capabilities to control the
supported protocol(s).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few hardware Remote Controller decoders, even using a standard protocol,
aren't able to provide the entire scancode. Due to that, the capability
of using other IR's are limited on those hardware.
Adds a way to indicate to ir-core what are the bits that the hardware
provides, from a scancode, allowing the addition of a complete IR table
to the kernel and allowing a limited support for changing the Remote
Controller on those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The keymaps don't need to be recompiled every time a change at ir-core.h
happens, since it only depends on rc-map defines. By moving those
definitions to the proper header, the code became cleaner, and avoids
needing to recompile all the RC maps every time a non-related change
is introduced.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the decoders are state machine, there's no need to create
an ancillary buffer while decoding the protocol. Just call the decoders
code directly, event by event.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This decoder is also based on a state machine, just like the NEC protocol
decoder. It is pedantic in the sense that accepts only 14 bits. As there
are some variants that outputs less bits, it needs to be improved to also
handle those.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrites the keyup/keydown logic in drivers/media/IR/ir-keytable.c.
All knowledge of keystates etc is now internal to ir-keytable.c
and not scattered around ir-raw-event.c and ir-nec-decoder.c (where
it doesn't belong).
In addition, I've changed the API slightly so that ir_input_dev is
passed as the first argument rather than input_dev. If we're ever
going to support multiple keytables we need to move towards making
ir_input_dev the main interface from a driver POV and obscure away
the input_dev as an implementational detail in ir-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch rewrites much of the keytable code in
drivers/media/IR/ir-keytable.c.
The scancodes are now inserted into the array in sorted
order which allows for a binary search on lookup.
The code has also been shrunk by about 150 lines.
In addition it fixes the following bugs:
Any use of ir_seek_table() was racy.
ir_dev->driver_name is leaked between ir_input_register() and
ir_input_unregister().
ir_setkeycode() unconditionally does clear_bit() on dev->keybit
when removing a mapping, but there might be another mapping with
a different scancode and the same keycode.
This version has been updated to incorporate patch feedback from
Mauro Carvalho Chehab.
[mchehab@redhat.com: Fix a conflict with RC keytable breakup patches and input changes]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the remote keymaps were broken into separate modules,
get rid of the keycode tables that were hardcoded into ir-common.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the ugly keymap sequences, use the new rc-*.ko keymap
files. For now, it is still needed to have one keymap loaded, for the
RC code to work. Later patches will remove this depenency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A latter patch will reuse the ir_input_register with a different meaning.
Before it, change all occurrences to a temporary name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having all RC tables hardcoded on one file with
all tables there, add infrastructure for registering and dynamically
load the table(s) when needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big file with lots of keytables, create one include
file for each IR keymap.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usage of macros ensures that the proper namespace is being used
by all tables. It also makes easier to associate a keytable with
the name used inside the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the first patch of a series of changes that will break the IR
tables into a series of small modules that can be dynamically loaded,
or just loaded from userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add CHIP ID of the NEC MPEG2 encoders uPD61151 and uPD61152.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Especially when IR needs to do polling, it generates lots of wakeups per
second. This makes no sense, if the input event device is closed.
Adds a callback handler to the IR hardware driver, to allow registering
an open/close ops.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some decoders and a lirc_dev interface may need some other operations to work.
For example: IR device register/unregister and ir_keydown events may need to
be tracked.
As some operations can occur in interrupt time, and a lock is needed to prevent
un-registering a decode while decoding a key, the lock needed to be convert
into a spin lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of hardcoding the protocols into ir-core, add a register interface
for the IR protocol decoders, and convert ir-nec-decoder into a client of
ir-core.
With this approach, it is possible to dynamically load the needed IR protocols,
and to add a RAW IR interface module, registered as one IR raw protocol decoder.
This patch opens a way to register a lirc_dev interface to work as an userspace
IR protocol decoder.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At raw_decode mode, the key is processed after the end of a timer. The
previous code resets the timer every time something is received at the IR
port. While this works fine with IR's that don't implement repeat, like
Avermedia RM-JX IR, it keeps waiting until keydown, on IR's that implement
NEC repeat command, like the Terratec yellow.
The solution is to change the behaviour to do the timeout after the first
received data.
The timeout is currently set to 15 ms, as it works fine with NEC protcocol.
It may need some adjustments to support other protocols and to better handle
spurious detections that may happen with some IR sensors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a method to pass IR raw pulse/code events into ir-core. This is
needed in order to support LIRC. It also helps to move common code
from the drivers into the core.
In order to allow testing, it implements a simple NEC protocol decoder
at ir-nec-decoder.c file. The logic is about the same used at saa7134
driver that handles Avermedia M135A and Encore FM53 boards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the devices like AM3517, it is expected that driver clears the
interrupt in ISR. Since this is device spcific, callback function
added to the platform_data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support SPI bus to v4l2. Useful for control some device with SPI bus like
hardware MPEG2 encoders and etc.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This list should stay sorted to make it easy to find new ID ranges when
adding new chip families.
[mchehab@redhat.com: fixed bad whitespacing]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, both driver and keytable names are exported to userspace. This
will help userspace to decide when a table need to be replaced
by another one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the ir-sysfs approach to create irrcv0 as a device, instead of
using class_dev. Also, change the way input is registered, in order
to make its parent to be the irrcv device.
Due to this change, now the event device is created under
/sys/class/ir/irrcv class:
/sys/class/irrcv/irrcv0/
|-- current_protocol
|-- device -> ../../../1-3
|-- input9
| |-- capabilities
| | |-- abs
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To save power soc-camera powers subdevices down, when they are not in use,
if this is supported by the platform. However, the V4L standard dictates,
that video nodes shall preserve configuration between uses. This requires
runtime power management, which is implemented by this patch. It allows
subdevice drivers to specify their runtime power-management methods, by
assigning a type to the video device.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This will remove the following sparse warning (see "make C=1"):
* incorrect type in argument 1 (different signedness)
expected unsigned int *start
got signed int *<noident>
as well as a couple more signedness mismatches.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An earlier regression fix for the mxb driver (V4L/DVB: saa7146_vv: fix
regression where v4l2_device was registered too late) caused a new
regression in the av7110 driver.
Reverted the old fix and fixed the problem in the mxb driver instead.
Tested on mxb and budget-av cards.
The real problem is that the saa7146 framework has separate probe()
and attach() driver callbacks which should be rolled into one. This
is now done for the mxb driver, but others should do the same. Lack
of hardware makes this hard to do, though. I hope to get hold of some
hexium cards and then I can try to improve the framework to prevent
this from happening again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sony makes custome tuners for its GigaPocket line of ivtv based capture
cards. This adds an entry to the tuner-types list for such tuners.
Parameters are based on experiments by Eric Anderson <rico99@sbcglobal.net>.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enhancements to support DM365 ISP5 and VPSS module configuration.
Also cleaned up the driver by removing redundant variables.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the header file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for
YUV capture from TVP514x driver. This patch contains the header files required
for this driver.
Reviewed-by: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the saa7111 driver was merged into saa7115 several bugs were introduced,
in particular with the saa7111a support as is used in the mxb.c driver.
This patch fixes the saa7111a support. This was tested with the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_register needs to be called before the i2c subdevs are loaded.
However, it was called afterwards in the saa7146 driver. This caused an oops
when loading the mxb and hexium drivers. The vv_init function is now split
into two: one registers the v4l2_device, the other does the rest of the
initialization. The three drivers that depend on this have been updated to
call the new vv_devinit function.
Thanks to Michael Hunold for reporting this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides the required definitions for the TVP7002 driver
in DM365.
Signed-off-by: Santiago Nunez-Corrales <santiago.nunez@ridgerun.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides required chip identification definitions
within v4l2. Included only definitions for TVP7002.
Signed-off-by: Santiago Nunez-Corrales <santiago.nunez@ridgerun.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just pass VIDIOC_S_PARM and VIDIOC_G_PARM down to host drivers. So far no
special handling in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes "buswidth" struct member, and sets the default buswidth
to the natively supported 10 bit. You can select 8 bit buswidth by new flag.
This patch also modify ap325rxa/migor setup.c
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add supports for the radio system on the Intel Russellville board.
It's a In-Vehicle Infotainment board with a radio tuner and DSP.
This umbrella driver has the DSP and tuner as V4L2 subdevs and calls them
when needed.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial support for the SAA7706H Car Radio DSP.
It is a I2C device and currently the mute control is supported.
When the device is unmuted it is brought out of reset and initiated using
the proposed intialisation sequence.
When muted the DSP is brought into reset state.
[akpm@linux-foundation.org: include delay.h]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: Douglas Schilling Landgraf <dougsland@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fix Video/Sound support "Leadtek winfast tv usbii deluxe".
Now, it is working Stereo, IR, Radio, TV, Svideo and Composite.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change attempts to fix the ivtv tinny audio problem by keeping digitizer
to encoder audio clocks running, while disabling the video clocks as needed to
avoid unpredictable PCI bus hangs.
To accomplish this, for the cx25840 module enabling of audio streaming had
to be separated from enabling video streaming, requiring an additional
v4l2_subdev_audio_op and calls to this new op in the pvrusb2 and ivtv drivers.
The cx231xx and cx23885 driver use the cx25840 module for affecting only
video on s_stream calls, so those drivers needed no change.
The CX23418 hardware does not exhibit either the tinny audio problem nor the PCI
bus hang, so the cx18 driver did not need corresponding changes.
CX2341[56] based cards that are not using the CX2584x family of chips
do not seem to be affected by the tinny audio problem, and this change should
not affect how they are configured. It will delay their first capture by
starting by another 300 msec though.
Many thanks go to Argus <pthorn-ivtvd@styx2002.no-ip.org> and
Martin Dauskardt <martin.dauskardt@gmx.de> whose persistent testing and
investigation of this problem will hopefully fix this problem once and for all
for many ivtv users.
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Reported-by: Argus <pthorn-ivtvd@styx2002.no-ip.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add sysfs skeleton to export remote controller information via
/sys/class/irrcv.
For now, the code doesn't do much. It just exports an attribute that
is meant to report and control the IR protocol used by the keytable.
However, the callbacks for this new attribute weren't set yet.
Also, it lacks symlinks to the used event interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It has been experimentally found out, that the sensor only supports up to
512x384 video output and also has some restrictions on minimum scale. We
disable non-working size ranges until, maybe, someone finds out how to properly
set them up. Also add cropping support, an auto white balance control, platform
data to specify master clock frequency and polarity of the IOCTL pin.
create mode 100644 include/media/rj54n1cb0c.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all soc-camera drivers to the new mediabus
API. This also takes soc-camera client drivers one step closer to also be
usable with generic v4l2-subdev host drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video subdevices, like cameras, decoders, connect to video bridges over
specialised busses. Data is being transferred over these busses in various
formats, which only loosely correspond to fourcc codes, describing how video
data is stored in RAM. This is not a one-to-one correspondence, therefore we
cannot use fourcc codes to configure subdevice output data formats. This patch
adds codes for several such on-the-bus formats and an API, similar to the
familiar .s_fmt(), .g_fmt(), .try_fmt(), .enum_fmt() API for configuring those
codes. After all users of the old API in struct v4l2_subdev_video_ops are
converted, it will be removed. Also add helper routines to support generic
pass-through mode for the soc-camera framework.
create mode 100644 drivers/media/video/soc_mediabus.c
create mode 100644 include/media/soc_mediabus.h
create mode 100644 include/media/v4l2-mediabus.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After this change drivers can be further extended to not fail, if they don't
get platform data, but to use defaults.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Up to now, if a client driver needed platform data apart from those contained
in struct soc_camera_link, it had to embed the struct into its own object. This
makes the use of such a driver in configurations other than soc-camera
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce new v4l2-subdev sensor operations, move .enum_framesizes() and
.enum_frameintervals() methods to it, add a new .g_skip_top_lines() method
and switch soc-camera to use it instead of .y_skip_top soc_camera_device
member, which can now be removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a helper function to get description of a digital
video preset added by the video timing API. This will be useful for drivers
implementing the above API.
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll need to register a sysfs class for the IR devices. As such, the better
is to have the input_register_device()/input_unregister_device() inside
the ir register/unregister functions.
Also, solves a naming problem with V4L ir_input_init() function, that were,
in fact, registering a device.
While here, do a few cleanups at budget-ci IR logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ir_input_free does more than just freeing the keytab. Better to
rename it as ir_input_unregister.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move non-V4L specific stuff from ir-functions ir_input_init() into
a new function to register ir devices: ir_input_register().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split the ir-common into two separate modules:
- ir-core: it is the IR-independent functions;
- ir-common: has the common part used by V4L drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the above APIs to the v4l2 core. This is based on version v1.2
of the RFC titled "V4L - Support for video timings at the input/output interface"
Following new ioctls are added:-
- VIDIOC_ENUM_DV_PRESETS
- VIDIOC_S_DV_PRESET
- VIDIOC_G_DV_PRESET
- VIDIOC_QUERY_DV_PRESET
- VIDIOC_S_DV_TIMINGS
- VIDIOC_G_DV_TIMINGS
Please refer to the RFC for the details. This code was tested using vpfe
capture driver on TI's DM365. Following is the test configuration used :-
Blu-Ray HD DVD source -> TVP7002 -> DM365 (VPFE) ->DDR
A draft version of the TVP7002 driver (currently being reviewed in the mailing
list) was used that supports V4L2_DV_1080I60 & V4L2_DV_720P60 presets.
A loopback video capture application was used for testing these APIs. This calls
following IOCTLS :-
- verify the new v4l2_input capabilities flag added
- Enumerate available presets using VIDIOC_ENUM_DV_PRESETS
- Set one of the supported preset using VIDIOC_S_DV_PRESET
- Get current preset using VIDIOC_G_DV_PRESET
- Detect current preset using VIDIOC_QUERY_DV_PRESET
- Using stub functions in tvp7002, verify VIDIOC_S_DV_TIMINGS
and VIDIOC_G_DV_TIMINGS ioctls are received at the sub device.
- Tested on 64bit platform by Hans Verkuil
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device::minor field is used where it shouldn't, either to
- test for error conditions that can't happen anymore with the current
v4l-dvb core,
- store the value in a driver private field that isn't used anymore,
- check the video device type where video_device::vfl_type should be
used, or
- create the name of a kernel thread that should get a stable name.
Remove or fix those use cases.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the video_is_unregistered function by a video_is_registered
function. The V4L2_FL_UNREGISTERED flag is replaced by a
V4L2_FL_REGISTERED flag.
This change makes the video_is_registered function return coherent
results when called on an initialize but not yet registered video_device
instance. The function can now be used instead of checking
video_device::minor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many drivers access the device number (video_device::v4l2_devnode::num)
in order to print the video device node name. Add and use a helper
function to retrieve the video_device node name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This IR uses NEC protocol, with address=0x14. This keymap is similar
to the existing Terratec Cinergy XS, except that:
- it contains the full address/command code;
- the Music button were mapped as KEY_RADIO;
- some keycodes from the previous entry were wrong, IMHO.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The same loop to seek for a key were used on different places. Also,
no spinlock were protecting it to avoid the risk of replacing a keycode
while seeking for a new code.
This cleanup does:
- create an unique function to seek for a code;
- adds an spinlock to protect the table lookup;
- remove some unused code;
- simplifies to code to make it easier to understand.
Basically no change in behavior should be noticed after this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the IR table is initialized by calling ir_input_init(). However,
this function doesn't return any error code, nor has a function to be called
when de-initializing the IR's.
Change the return argment to integer and make sure that each driver will
handle the error code. Also adds a function to free any resources that may
be allocating there: ir_input_free().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that V4L drivers can support more than 7 bits for scan code, let's
add a modified version for the Hauppauge Grey IR containing the full IR
scancode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the IR conversion to dynamic tables has finished, we can get
rid of some fields and definitions that aren't used anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L drivers use an static keycode vector with 128 entries, where the scancode
indexes the keycode. While this works, it limits the scancodes to have only
7 bits, not allowing for example full RC5 codes.
Instead of implementing the same code on every V4L driver, provide a common
infrastructure to handle the bigger tables, minimizing the changes inside
each driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As newer IR common code will be added on other files, we need a global
debug var inside the module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For whatever reason, the device structure pointer to
videobuf_queue_vmalloc_init is typed "void *", even though it's passed
right through to videobuf_queue_core_init(), which expects a struct
device pointer. The other videobuf implementations use struct device *;
I think vmalloc should too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_queue_ops function vector is not declared constant, but
there's no need for the videobuf layer to ever change it. Make it const
so that videobuf users can make their operations const without warnings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Upcoming I2C v4l2_subdev drivers need a way to control the subdevice
power state from the core. This use case is already partially covered by
the tuner s_standby operation, but no way to explicitly come back from
the standby state is available.
Rename the tuner s_standby operation to core s_power, and fix tuner
drivers accordingly. The tuner core will call s_power(0) instead of
s_standby(). No explicit call to s_power(1) is required for tuners as
they are supposed to wake up from standby automatically.
[mchehab@redhat.com: CodingStyle fix]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for TEF6862 Car Radio Enhanced Selectivity Tuner.
It's implemented as a subdev, supporting checking signal strength
and setting and getting frequency.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as TeVii S460,S420.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as:
TeVii S460,S420; Omicom SS4; SatTrade ST4200;
TBS 8920,8910; Prof 7300,6200.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds an soc-camera / v4l2-subdev driver for the RJ54N1CB0C CMOS camera
sensor from Sharp. The sensor is very picky about initialisation and
configuration sequences. The driver limits artificially maximum window size by
800x600, although the sensor supports 1600x1200. Sizes above 800x600 don't seem
to work correctly, besides, examples from the system integrator use sizes above
640x480 only for still photography. Unfortunately, I had to use "magic"
register-value pairs for undocumented and "reserved" registers. This version of
the driver also omits some functionality, like cropping, which hasn't been
sufficiently tested yet and will be added later.
create mode 100644 drivers/media/video/rj54n1cb0c.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add v4l2_subdev_ir_ops and IR notify defines for v4l2_device. This change
is specifically needed at this time to support the integrated IR controller in
the CX2388[58] chips.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add identifiers for CX2388[578] chips, CX2310[012] chips, integrated
A/V decoders cores, integrated IR controller core, and the CX23417
MPEG encoder. The cx23885 module and cx25840 module will use these
identifiers in upcoming changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an initial driver for Analog Devices ADV7180 Video Decoder.
So far it only supports query standard.
[akpm@linux-foundation.org: remove unneeded cast]
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warn when the desired device node number is already in use, except when
the new video_register_device_no_warn function is called since in some
use-cases that warning is not relevant.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_register_device_index is never actually called, instead the
stream index number is always calculated automatically.
This patch removes this function and simplifies the internal get_index
function since that can now always just return the first free index.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the soc-camera interface for V4L2 subdevices thinner yet. Handle
gain and exposure internally in each driver just like all other controls.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unneeded soc-camera operations, this also makes the soc-camera API to
v4l2 subdevices thinner.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial soc-camera scaling and cropping implementation turned out to be
incompliant with the V4L2 API, e.g., it expected the user to specify cropping
in output window pixels, instead of input window pixels. This patch converts
the soc-camera core and all drivers to comply with the standard.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_subdev_call() instead of v4l2_device_call_until_err() in all host
drivers and in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove set_crop soc-camera device method and switch to s_crop from v4l2-subdev
video operations. Also extend non-i2c drivers to also hold a pointer to their
v4l2-subdev instance in control device driver-data, i.e., in
dev_get_drvdata((struct device *)to_soc_camera_control(icd))
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The move of format translation initialisation into soc_camera_open() was
temporary for the soc-camera as platform driver intermediate step, put it back
into soc_camera_probe(). Also add a .put_formats() method to
soc_camera_host_ops to free any resources host driver might have allocated in
.get_formats().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to using struct v4l2_rect in struct soc_camera_device for uniformity and
simplicity.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now soc-camera only supported client (sensor) controls. This patch
enables camera-host drivers to implement their own controls too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the soc-camera framework to use the v4l2-(sub)dev API. Start using
v4l2-subdev operations. Only a part of the interface between the
soc_camera core, soc_camera host drivers on one side and soc_camera device
drivers on the other side is replaced so far. The rest of the interface
will be replaced in incremental steps, and will require extensions and,
possibly, modifications to the v4l2-subdev code.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all drivers to platform device API. We already
converted platforms to register a platform device for each soc-camera client,
now we remove the compatibility code and switch completely to the new scheme.
This is a preparatory step for the v4l2-subdev conversion.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a struct device pointer to struct soc_camera_platform_info and let the user
(ap325rxa) pass it down to soc_camera_platform.c in its .add_device() method.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_platform.c is only used by y SuperH ap325rxa board. This patch
converts soc_camera_platform.c and its users for the soc-camera platform-
device conversion and also extends soc-camera core to handle non-I2C cameras.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new module added for vpss library functions that are
used for configuring vpss system module. All video drivers will
include vpss.h header file and call functions defined in this
module to configure vpss system module.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the hw module for DM644x CCDC. This registers with the
vpfe capture driver and provides a set of hw_ops to configure
CCDC for a specific decoder device connected to the VPFE.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds ccdc hw module for DM355 CCDC. This registers with the bridge
driver a set of hw_ops for configuring the CCDC for a specific
decoder device connected to vpfe.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This the vpfe capture bridge driver for doing video
capture on DM355 and DM6446 evms. The ccdc hw modules register with the
driver and are used for configuring the CCD Controller for a specific
decoder interface. The driver also registers the sub devices required
for a specific evm. More than one sub devices can be registered.
This allows driver to switch dynamically to capture video from
any sub device that is registered. Currently only one sub device
(tvp5146) is supported. But in future this driver is expected
to do capture from sensor devices such as Micron's MT9T001, MT9T031
and MT9P031 etc. The driver currently supports MMAP based IO.
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for NXP TDA18271 as a standalone tuner, allowing the use of
analog demodulators other than the Philips/NXP TDA829x.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds files to control si4713 devices.
Internal functions to control device properties
and initialization procedures are into these files.
Also, a v4l2 subdev interface is also exported.
This way other drivers can use this as v4l2 i2c subdevice.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds files which creates the radio interface
for si4713 FM transmitter (modulator) devices.
In order to do the real access to device registers, this
driver uses the v4l2 subdev interface exported by si4713 i2c driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds driver for mt9v011 based on its datasheet, available at:
http://download.micron.com/pdf/datasheets/imaging/MT9V011.pdf
The driver was tested with a webcam that will be added on a next patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most hardware has limits on minimum and maximum image dimensions and also
requirements about alignment. For example, image width must be even or a
multiple of four. Some hardware has requirements that the total image size
(width * height) be a multiple of some power of two.
v4l_bound_align_image() will enforce min and max width and height, power of
two alignment on width and height, and power of two alignment on total
image size.
It uses an efficient algorithm that will try to find the "closest" image
size that meets the requirements.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new s_config core ops call: this is called with the irq and platform
data to be used to initialize the subdev.
Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls
that allows you to pass these new arguments.
The existing v4l2_i2c_new_subdev functions were modified to also call
s_config.
In the future the existing v4l2_i2c_new_subdev functions will be replaced
by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg
but without the irq and platform_data arguments.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it very clear that this header should not be used for i2c drivers that
do not need to be compiled for pre-2.6.26 kernels.
As soon as the minimum supported kernel in the v4l-dvb repository becomes
2.6.26 or up, then this header should be removed entirely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the standard device driver binding model, the name field of
struct i2c_client is used to match devices to their drivers, so we
must stop using it for internal purposes. Define a separate field
in struct IR_i2c as a replacement, and use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ADV7343 I2C based video encoder driver. This follows the
v4l2-subdev framework. This driver has been tested on TI DM646x EVM. It
has been tested for Composite and Component outputs.
Updates as per review by Mauro Chehab, added support for more standards
supported by the encoder. Also adding the missed out signed-offs.Tested
only NTSC and PAL standards.
[hverkuil@xs4all.nl: s_routing API changed, updated driver to use new API]
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds driver for TI THS7303 video amplifier. This driver is
implemented as a v4l2 sub device. Tested on TI DM646x EVM.
This version has updates based on review comments by Mauro Chehab.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a platform driver to soc_camera.c. This way we preserve backwards
compatibility with existing platforms and can start converting them one by one
to the new platform-device soc-camera interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now I relied on i2c_del_adapter to unregister the i2c_clients for
me, however, if the i2c bus is a platform bus then it is never deleted.
So instead I need to unregister i2c clients when unregistering the
v4l2_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a utility function that can be used to setup the v4l2_device's name
field in a standard manner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make camera devices direct children of host platform devices, move the
inheritance management into the soc_camera.c core driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently pcm990 camera bus-width management functions request a GPIO and never
free it again. With this approach the GPIO extender driver cannot be unloaded
once camera drivers have been loaded, also unloading theb i2c-pxa bus driver
produces errors, because the GPIO extender driver cannot unregister properly.
Another problem is, that if camera drivers are once loaded before the GPIO
extender driver, the platform code marks the GPIO unavailable and only a reboot
helps to recover. Adding an explicit free_bus method and using it in mt9m001
and mt9v022 drivers fixes these problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The name size limit is gone from the driver core, the BUS_ID_SIZE
value will be removed.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove support for the debug call VIDIOC_INT_S_AUDIO_ROUTING from cx18
and ivtv. These internal ioctls shouldn't be exposed. These were only
used through the cx18-ctl and ivtv-ctl utilities, and only when testing
a new card variant.
This cleanup allows the removal of this ioctl from v4l2-common.h.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With all the v4l2_subdev changes that were made to these drivers it is a
good idea to increase the version number of each driver.
It's just the patch level that is increased, except for the zoran and saa7146
drivers where the minor number was increased due to the more substantial
changes that were made to those two drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than duplicating this list everywhere, just put it in tvaudio.h.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add utility function to probe for a single address, rather than a list
of addresses.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Originally the intention was to switch to the new style i2c API starting with
the introduction of the API in 2.6.22. However, the i2c_new_probed_device()
function has a lethal bug that wasn't fixed until 2.6.25. Or more accurately,
it was only fixed in the stable series of 2.6.25 and 2.6.26.
Given the fact that the new i2c API also changed starting with 2.6.26 (the
addition of i2c_device_id), it is easiest to switch APIs starting with
2.6.26.
This patch updates all the legacy code accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init callback was used in several places to load firmware. Make a separate
load_fw callback for that. This makes the code a lot more understandable.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that all drivers are converted to v4l2_subdev we can remove legacy code
in v4l2-common. Also move the documentation of the internal API to
v4l2-subdev.h where it really belongs.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-subdev.c and v4l2-i2c-drv-legacy.h were used to support the old i2c
API. All v4l drivers are now converted to v4l2_subdev, so these two files
can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kassey Li