If set_fmt callback is called with format->width or format->height set to
zero and HACTIVE_CNT or VACTIVE_CNT bits (respectively) in chip are zero
we will divide by zero later in this callback when we try to calculate
HSC or VSC values.
Fix this by explicitly rejecting these values.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 0b1100 value in 4 LSBs of "General Status 1" register (AFD_FMT_STAT) has
known meaning for CX2584x-series chips - it means that a SECAM signal is
currently detected by the chip.
Use this opportunity to also fix wrong binary values that were present
as comments attached to some entries in an array where
chip register -> V4L2 standard mappings are stored.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of_node_full_name() now returns only the basename, the endpoint
information printed became useless:
adv748x 4-0070: Endpoint endpoint on port 7
adv748x 4-0070: Endpoint endpoint on port 8
adv748x 4-0070: Endpoint endpoint on port 10
adv748x 4-0070: Endpoint endpoint on port 11
Restore the old behavior by using "%pOF" instead:
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11
Fixes: a7e4cfb0a7 ("of/fdt: only store the device node basename in full_name")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 'return' was missing when detecting Arbitration Lost and
calling transmit_done. With the return transmit_done could be
called a second time, confusing the CEC framework. Luckily
the Arbitration Lost condition is very rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate checks.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current implementation has to search the list of controls for the
pixel rate control, each time it is set. This can be optimised easily
by storing the ctrl pointer in the CSI/TX object, and referencing that
directly.
While at it, fix up a missing blank line also highlighted in review
comments.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mt9v032_power_on() leaves clk enabled in case of errors,
but it is not expected by its callers.
There is a similar problem in mt9v032_registered().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov7670 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sub-device for ov7670 is registered by v4l2_async_register_subdev().
So it should be unregistered by v4l2_async_unregister_subdev() instead of
v4l2_device_unregister_subdev().
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the missing MAINTAINERS entry for imx274, fix error handling in driver
probe and unregister the correct control handler in driver remove.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_async_register_subdev_sensor_common() is only provided when
CONFIG_V4L2_FWNODE is enabled, otherwise we get a link failure:
drivers/media/i2c/et8ek8/et8ek8_driver.o: In function `et8ek8_probe':
et8ek8_driver.c:(.text+0x884): undefined reference to `v4l2_async_register_subdev_sensor_common'
This adds a Kconfig 'select' statement like all the other users of
this interface have.
Fixes: d8932f38c1 ("media: et8ek8: Add support for flash and lens devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov13858 driver depends on the V4L2 fwnode, thus add that to Kconfig.
Fixes: 5fcf092e0c ("[media] ov13858: add support for OV13858 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this warning:
drivers/media/i2c/lm3560.c:69: warning: No description found for parameter 'dev'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some struct fields that aren't documented, and some
consts whose comments start with /**, but they aren't kernel-doc
annotations. So, fix it:
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'hdl'
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'pad'
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'format'
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'int_seq'
drivers/media/i2c/tvp514x.c:219: warning: cannot understand function prototype: 'const struct v4l2_fmtdesc tvp514x_fmt_list[] = '
drivers/media/i2c/tvp514x.c:235: warning: cannot understand function prototype: 'const struct tvp514x_std_info tvp514x_std_list[] = '
drivers/media/i2c/tvp514x.c:941: warning: No description found for parameter 'fmt'
drivers/media/i2c/tvp514x.c:941: warning: Excess function parameter 'format' description in 'tvp514x_set_pad_format'
drivers/media/i2c/tvp514x.c:1208: warning: cannot understand function prototype: 'const struct i2c_device_id tvp514x_id[] = '
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
as warned:
drivers/media/i2c/s5k6aa.c:429: warning: No description found for parameter 's5k6aa'
drivers/media/i2c/s5k6aa.c:679: warning: No description found for parameter 's5k6aa'
drivers/media/i2c/s5k6aa.c:733: warning: No description found for parameter 's5k6aa'
drivers/media/i2c/s5k6aa.c:733: warning: No description found for parameter 'preset'
drivers/media/i2c/s5k6aa.c:787: warning: No description found for parameter 'sd'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/i2c/s5k6a3.c:68: warning: No description found for parameter 'clock'
drivers/media/i2c/s5k6a3.c:68: warning: No description found for parameter 'clock_frequency'
drivers/media/i2c/s5k6a3.c:68: warning: No description found for parameter 'power_count'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those warnings:
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'addr_num'
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'addr_den'
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'val'
drivers/media/i2c/m5mols/m5mols_capture.c:60: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_controls.c:134: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:124: warning: No description found for parameter 'data'
drivers/media/i2c/m5mols/m5mols_core.c:124: warning: No description found for parameter 'length'
drivers/media/i2c/m5mols/m5mols_core.c:124: warning: Excess function parameter 'size' description in 'm5mols_swap_byte'
drivers/media/i2c/m5mols/m5mols_core.c:142: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:241: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:299: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:324: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:324: warning: No description found for parameter 'reg'
drivers/media/i2c/m5mols/m5mols_core.c:357: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:357: warning: No description found for parameter 'mode'
drivers/media/i2c/m5mols/m5mols_core.c:374: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:429: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:503: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:671: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:694: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:798: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:853: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:853: warning: No description found for parameter 'on'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
The variable ret is being checked for failure however it is not being set
from the return status from the call to imx274_mode_regs. Currently ret is
alwayus zero and the check is redundant. Fix this by assigning it.
Detected by CoverityScan, CID#1460278 ("Logically dead code")
Fixes: 0985dd306f ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
These types devices aren't directly related to the sensor, but are
nevertheless handled by the smiapp driver due to the relationship of these
component to the main part of the camera module --- the sensor.
This does not yet address providing the user space with information on how
to associate the sensor or lens devices but the kernel now has the
necessary information to do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The test_pattern_menu[] array has two valid items and a null terminated
item. So the control's maximum value which is passed to
v4l2_ctrl_new_std_menu_items() should be one. However,
'ARRAY_SIZE(test_pattern_menu) - 1' is actually passed and it's not
correct.
Fix it by removing unnecessary terminated entry and let the correct
control's maximum value be passed to v4l2_ctrl_new_std_menu_items().
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The TC358743 does not support more than 4 data lanes. Check that the
lane count is valid.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When I was supporting Rpi Camera Module on the ASUS Tinker board,
I found this driver have some issues with rockchip's mipi-csi driver.
It didn't place clock lane in LP-11 state before performing
D-PHY initialisation.
>From our experience, on some OV sensors,
LP-11 state is not achieved while BIT(5)-0x4800 is cleared.
So let's set BIT(5) and BIT(0) both while not streaming, in order to
coax the clock lane into LP-11 state.
0x4800 : MIPI CTRL 00
BIT(5) : clock lane gate enable
0: continuous
1: none-continuous
BIT(0) : manually set clock lane
0: Not used
1: used
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the ov7670_s_power function which is responsible for
manipulating the power dowm mode through the PWDN pin and the reset
operation through the RESET pin, and keep it powered at all times.
[sakari.ailus@linux.intel.com: set pwdn_gpio direction only once]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the get_fmt callback, also enable V4L2_SUBDEV_FL_HAS_DEVNODE flag
to make this subdev has device node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the media entity pads initialization.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The imx274 is a Sony CMOS image sensor that has 1/2.5 image size.
It supports up to 3840x2160 (4K) 60fps, 1080p 120fps. The interface
is 4-lane MIPI CSI-2 running at 1.44Gbps each.
This driver has been tested on Xilinx ZCU102 platform with a Leopard
LI-IMX274MIPI-FMC camera board.
Support for the following features:
-Resolutions: 3840x2160, 1920x1080, 1280x720
-Frame rate: 3840x2160 : 5 – 60fps
1920x1080 : 5 – 120fps
1280x720 : 5 – 120fps
-Exposure time: 16 – (frame interval) micro-seconds
-Gain: 1x - 180x
-VFLIP: enable/disabledrivers/media/i2c/imx274.c
-Test pattern: 12 test patterns
Signed-off-by: Leon Luo <leonl@leopardimaging.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TC358743 is an HDMI to MIPI CSI2-2 bridge.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can remove the check for if "state->cec_adap" is NULL. The
cec_allocate_adapter() function never returns NULL and also we verified
that "state->cec_adap" is an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It should be "LP-11".
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on a mix of runtime PM and the s_power() callback, drop
the s_power() callback altogether and use runtime PM solely.
As device access is required during device power-on and power-off
sequences, runtime PM alone cannot tell whether the device is available.
Thus the "active" field is introduced in struct smiapp_sensor to tell
whether it is safe to write to the device.
Consequently there is no need to power on the device whenever a file
handle is open. This functionality is removed as well. The user may still
control the device power management through sysfs. Autosuspend remains
enabled, with 1 s delay.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use unlocked __v4l2_ctrl_handler_setup() in order to make the
control setup atomic.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The clock control is not explicitly controlled by the driver in two cases:
ACPI based systems and when the clock is part of the power sequence of the
camera module.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Obtain the clock rate from the clock framework if it's not available
through DT. The assumption is that the parent device (camera module)
defines the rate as clock control is a part of the power on and power off
sequences --- which are camera module specific.
Also use the clock rate from DT if no clock is provided.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The external clock frequency was set by the driver but the obtained
frequency was never verified. Do that.
Being able to obtain the exact frequency is important as the value is used
for PLL calculations which may result in frequencies that violate the PLL
tree limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The error handling code in smiapp_power_on() returned in case of a failed
I2C write instead of cleaning up the mess. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Maciej S. Szmigiero