The ov7670 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sub-device for ov7670 is registered by v4l2_async_register_subdev().
So it should be unregistered by v4l2_async_unregister_subdev() instead of
v4l2_device_unregister_subdev().
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the ov7670_s_power function which is responsible for
manipulating the power dowm mode through the PWDN pin and the reset
operation through the RESET pin, and keep it powered at all times.
[sakari.ailus@linux.intel.com: set pwdn_gpio direction only once]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the get_fmt callback, also enable V4L2_SUBDEV_FL_HAS_DEVNODE flag
to make this subdev has device node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the media entity pads initialization.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When devm_clk_get() fails the real error code should be propagated,
instead of always returning -EPROBE_DEFER.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add DT support. Use it to get the reset and pwdn pins (if there are any).
Tested with one sensor requiring reset/pwdn and one sensor that doesn't
have reset/pwdn pins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Get the clock for this sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop unnecesary memset. Drop the unnecessary extendedmode check and
set the V4L2_CAP_TIMEPERFRAME capability.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add v4l2-async support for this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The try_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Since try_mbus_fmt and s_mbus_fmt both map to the set_fmt pad op (but
with a different 'which' argument), this patch will replace both
try_mbus_fmt and s_mbus_fmt by set_fmt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to the enum_mbus_fmt video op by the pad
enum_mbus_code op and remove the duplicate video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though the format is Y'CbCr, the colorspace used by the sensor
is almost certainly SRGB. The sensor is also not generating JPEG data,
so it makes no sense to use V4L2_COLORSPACE_JPEG here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The width and height should be checked in the enum_frame_interval
op. This fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ov7670_s_exp() checks read error for 2 registers: REG_COM1
and REG_COM8. But, although it uses the value latter, it
doesn't check errors on REG_AECHH read. Yet, as it is doing
a bitmask operation there, the read operation should succeed.
So, fix the code to also check if this succeeded.
This fixes this smatch report:
drivers/media/i2c/ov7670.c:1366 ov7670_s_exp() warn: inconsistent indenting
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_interval ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Tested for ov7670 and marvell-ccic on a OLPC XO-1 laptop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definitions to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Replace all references to the old definitions in i2c drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 75e2bdad89 "ov7670: allow
configuration of image size, clock speed, and I/O method" uses a wrong
index to iterate an array. Apart from being wrong, it also uses an
unchecked value from user-space, which can cause access to unmapped
memory in the kernel, triggered by a normal desktop user with rights to
use V4L2 devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is no longer needed since the core now handles this through DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes check for EPERM in dbg_g/s_register of subdevice
drivers as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
via-camera and mcam-core were the only bridge drivers that used ov7670.
Since now they have been moved to use the ctrl framework, the old
legacy callbacks in the ov7670 can be removed.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some bridge drivers capture pixels during blanking periods if
pixclk is enabled. In order to avoid capturing bogus data we need to
disable pixclk in the sensor during those blanking periods.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For a frame rate of 30 fps a pixclk of 24MHz is needed. For those
cases where the ov7670 has a clean 24MHz input (xvclk) the PLL
can be bypassed.
This will result in a value of clkrc of 1, which means that in practice
pixclk = xvclk (input clock)
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the datasheet ov7675 uses a formula to achieve
the desired framerate that is different from the operations
done in the current code.
In fact, this formula should apply to ov7670 too. This would
mean that current code is wrong but, in order to preserve
compatibility, the new formula will be used for ov7675 only.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'min_height' and 'min_width' are variables that allow to specify the minimum
resolution that the sensor will achieve. This patch make v4l2 fmt callbacks
consider this parameters in order to return valid data to user space.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov7675 and ov7670 share the same registers but there is no way
to distinguish them at runtime. However, they require different
tweaks to achieve the desired resolution. For this reason this
patch adds a new ov7675 entry to the ov7670_id table.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
4x gain ceiling is not enough to capture a decent image in conditions
of total darkness and only a LED light source. Allow a maximum gain
of 32x instead.
This doesn't have any drawback since the image quality in 'normal'
light conditions is the same.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Akinobu Mita