Add pre-dsp download initialization for the DAC's used in the surround
sound configuration. Fixes issues of no audio on surround channels.
Fixes: 2e492b8ee5 ("ALSA: hda/ca0132 - Add ZxR init commands")
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201211225504.4508-2-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The check for infoframe transmit status in hdmi_infoframe_uptodate()
makes the assumption that packet buffer index is set to zero.
Align code with specification and explicitly set the index before
AC_VERB_GET_HDMI_DIP_XMIT. The packet index setting affects both
DIP-Data and DIP-XmitCtrl verbs.
There are no known cases where the old implementation has caused driver
to work incorrectly. This change is purely based on code review against
the specification (HDA spec rev1.0a).
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211131613.3271407-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The debug prints from patch_hdmi.c are not aligned with HDA common code
in hda_codec.c nor with other HDA codec drivers.
To align with rest of the codebase, use hexadecimal formatting whenever
printing value of a HDA NID. Also refer to NIDs with capital letters in
traces as is done other modules. This presentation is also aligned with
the formatting used in HDA codec procfs entry.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211124547.3243871-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the DSP's audio configuration is understood, remove previous
hacky methods of trying to properly configure it.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-6-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make sure that the DSP has no DMA channels allocated once the firmware
is downloaded, and that the default audio streams in use by the DSP are
setup in the correct order.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-5-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add functions for both reading and writing to the 8051's exram. Also,
add a little bit of documentation on how the addresses are segmented.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-4-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reset the codec upon initialization to clear out anything that may have
been setup on a previous boot into Windows, or in case of an improper
shutdown.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-2-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A problem exists in enabling silent stream when connection type is
DisplayPort. Silent stream programming is completed when a new DP
receiver is connected, but infoframe transmission does not actually
start until PCM is opened for the first time. This can result in audible
gap of multiple seconds. This only affects the first PCM open.
Fix the issue by properly assigning a converter to the silent stream,
and modifying the required stream ID programming sequence.
This change only affects Intel display audio codecs.
BugLink: https://github.com/thesofproject/linux/issues/2468
Fixes: 951894cf30 ("ALSA: hda/hdmi: Add Intel silent stream support")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201210174445.3134104-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that the HD-audio clear and reconfig sysfs don't work any
longer after the recent driver core change. There are multiple issues
around that: the linked list corruption and the dead device handling.
The former issue is fixed by another patch for the driver core itself,
while the latter patch needs to be addressed in HD-audio side.
This patch corresponds to the latter, it recovers those broken
functions by replacing the device detach and attach actions with the
standard core API functions, which are almost equivalent with unbind
and bind actions.
Fixes: 654888327e ("driver core: Avoid binding drivers to dead devices")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209207
Link: https://lore.kernel.org/r/20201209150119.7705-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS laptop Q524UQK with ALC255 codec can't detect the headset
microphone until ALC255_FIXUP_ASUS_MIC_NO_PRESENCE quirk applied.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209045730.9972-1-chiu@endlessos.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To help in debugging issues with DisplayPort Multi-Stream Transport (aka
DP-MST) support, print information of active connections for each device
of a display audio pin widget.
Example output with the patch with two monitors connected to a DP-MST hub:
Devices: 4
Dev 00: PD = 0, ELDV = 0, IA = 0, Connections [ 0x03* 0x05 0x07 0x09 ]
Dev 01: PD = 1, ELDV = 1, IA = 0, Connections [ 0x03* 0x05 0x07 0x09 ]
*Dev 02: PD = 1, ELDV = 1, IA = 0, Connections [ 0x03 0x05* 0x07 0x09 ]
Dev 03: PD = 0, ELDV = 0, IA = 0, Connections [ 0x03* 0x05 0x07 0x09 ]
Connection: 4
0x03 0x05* 0x07 0x09
Format of existing "Connection:" entry is left intact to keep
compatibility.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201208185736.2877541-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS laptop X430UN with ALC256 can't detect the headset microphone
until ALC256_FIXUP_ASUS_MIC_NO_PRESENCE quirk applied.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201207072755.16210-1-chiu@endlessos.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This change could fix 2 issues on this machine:
- the bass speaker's output volume can't be adjusted, that is because
the bass speaker is routed to the DAC (Nid 0x6) which has no volume
control.
- after plugging a headset with vol+, vol- and pause buttons on it,
press those buttons, nothing happens, this means those buttons
don't work at all. This machine has alc287 codec, need to add the
codec id to the disable/enable_headset_jack_key(), then the headset
button could work.
The quirk of ALC285_FIXUP_THINKPAD_HEADSET_JACK could fix both of these
2 issues.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20201205051130.8122-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Spectre x360 Convertible 15" version (SSID 103c:827f) needs the
same quirk to make the mute LED working like other models.
System Information
Manufacturer: HP
Product Name: HP Spectre x360 Convertible 15-bl1XX
Sound Codec:
Codec: Realtek ALC295
Vendor Id: 0x10ec0295
Subsystem Id: 0x103c827f
Revision Id: 0x100002
Reported-by: <christoph.plattner@gmx.at>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201128090015.7743-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The setup of unsolicited event callbacks should be done only once at
the parser phase, not in the init phase that is called multiple times
at each resume.
This patch moves the unsol setup code in ca0132 codec driver to the
more appropriate place.
Reported-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200930113008.9307-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Zephyrus G14 has two speaker pins, and the auto-parser tries to
assign an individual DAC to each pin as much as possible.
Unfortunately the third DAC has no volume control unlike the two DACs,
and this resulted in the inconsistent speaker volumes.
As a workaround, wire both speaker pins to the same DAC by modifying
the existing quirk (ALC289_FIXUP_ASUS_GA401) applied to this device.
Since this quirk entry is chained by another, we need to avoid
applying the DAC assignment change for it. Luckily, there is another
quirk entry (ALC289_FIXUP_ASUS_GA502) doing the very same thing, so we
can chain to the GA502 quirk instead.
Note that this patch uses a new flag of the generic parser,
obey_preferred_dacs, for enforcing the DACs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210359
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops like ASUS UX482EG & B9400CEA's headset audio does not work
until the quirk ALC294_FIXUP_ASUS_HPE is applied.
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201124092024.179540-1-jhp@endlessos.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'pci_set_dma_mask()' + 'pci_set_consistent_dma_mask()' can be replaced by
an equivalent 'dma_set_mask_and_coherent()' which is much less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201121083747.1330299-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This platform only had one audio jack.
If it plugged speaker then replug with speaker or headset, the sound
tone will change to abnormal.
Headset Mic also can't record when this issue was happen.
[ Added a short comment about the COEF by tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/593c777dcfef4546aa050e105b8e53b5@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code change for switching to non-atomic mode brought the
unexpected mutex deadlock in get_msg(). It converted the spinlock
with the existing mutex, but there were calls with the already holding
the mutex. Since the only place that needs the extra lock is the code
path from snd_mixart_send_msg(), remove the mutex lock in get_msg()
and apply in the caller side for fixing the mutex deadlock.
Fixes: 8d3a8b5cb5 ("ALSA: mixart: Use nonatomic PCM ops")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201119121440.18945-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_PCI=n leads to a compile warning like:
sound/pci/hda/patch_ca0132.c:8214:10: warning: no case matching constant switch condition '0'
due to the missed handling of QUIRK_NONE in ca0132_mmio_init().
Fix it.
Fixes: bf2aa9ccc8 ("ALSA: hda/ca0132 - Cleanup ca0132_mmio_init function.")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201119120404.16833-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
System boot or warm boot with plugged headset.
If it turn on power save mode, Headset Mic will lose.
This patch will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1ae4d98e92c147b780ace3911c4e1d73@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Pavilion x360 Convertible machine, it supported mute led.
GPIO4 high will turn on led.
The patch will enable control led via GPIO4 pin.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1ae4d98e92c147b780ace3911c4e1d73@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix "use as headset mic, without its own jack detect" problem.
[ Minor coding style fixes by tiwai ]
Signed-off-by: PeiSen Hou <pshou@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/481963e4a5694ff19f27ae1e283d79ad@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS TM420 had depop circuit for headphone.
It need to turn on by COEF bit.
[ fixed the missing enum definition by tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/3d6177d7023b4783bf2793861c577ada@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The broken jack detection should be fixed by commit a6e7d0a4bd ("ALSA:
hda: fix jack detection with Realtek codecs when in D3"), let's try
enabling runtime PM by default again.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201027130038.16463-4-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both pm_runtime_force_suspend() and pm_runtime_force_resume() have
some implicit checks, so it can make code flow more straightforward if
we separate runtime and system suspend callbacks.
High Definition Audio Specification, 4.5.9.3 Codec Wake From System S3
states that codec can wake the system up from S3 if WAKEEN is toggled.
Since HDA controller has different wakeup settings for runtime and
system susend, we also need to explicitly disable direct-complete which
can be enabled automatically by PCI core. In addition to that, avoid
waking up codec if runtime resume is for system suspend, to not break
direct-complete for codecs.
While at it, also remove AZX_DCAPS_SUSPEND_SPURIOUS_WAKEUP, as the
original bug commit a6630529ae ("ALSA: hda: Workaround for spurious
wakeups on some Intel platforms") solves doesn't happen with this
patch.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201027130038.16463-3-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upon system resume, hda_codec_pm_resume() uses hda_codec_force_resume()
to resume the codec. However, pm_runtime_force_resume() won't really
resume the codec because of pm_runtime_need_not_resume() check.
Hence, hda_codec_force_resume() schedules a jackpoll work, which is to
really power up the codec.
Instead of doing that, we can use direct-complete to make the PM flow
more straightforward, and keep codec always suspended through system PM
flow if conditions are met.
On system suspend, PM core will decide what to do based on
hda_codec_pm_prepare():
- If codec is not runtime-suspended, PM core will suspend and resume the
device as normal.
- If codec is runtime-suspended, PM core will try to keep it suspended.
If it's still suspended after system resume, we use
hda_codec_pm_complete() to resume codec if it's needed.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201027130038.16463-2-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
System boot with plugged headset. It will not detect headset Mic.
It will happen on cold boot restart resume state.
Quirk by SSID change to quirk by pin verb.
Fixes: 13468bfa8c ("ALSA: hda/realtek - set mic to auto detect on a HP AIO machine")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/f42ae1ede1cf47029ae2bef1a42caf03@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A break is not needed if it is preceded by a return, goto
or break
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201019164857.27223-1-trix@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the cb function is already registered, should return the pointer
of the structure hda_jack_callback which contains this cb func, but
instead it returns the NULL.
Now fix it by replacing func_is_already_in_callback_list() with
find_callback_from_list().
Fixes: f4794c6064 ("ALSA: hda - Don't register a cb func if it is registered already")
Reported-and-suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20201022030221.22393-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't populate const arrays on the stack but instead make them
static. Makes the object code smaller by 57 bytes.
Before:
text data bss dec hex filename
173256 38016 192 211464 33a08 sound/pci/hda/patch_ca0132.o
After:
text data bss dec hex filename
172879 38336 192 211407 339cf sound/pci/hda/patch_ca0132.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201016224913.687724-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A race exists between closing a PCM and update of ELD data. In
hdmi_pcm_close(), hinfo->nid value is modified without taking
spec->pcm_lock. If this happens concurrently while processing an ELD
update in hdmi_pcm_setup_pin(), converter assignment may be done
incorrectly.
This bug was found by hitting a WARN_ON in snd_hda_spdif_ctls_assign()
in a HDMI receiver connection stress test:
[2739.684569] WARNING: CPU: 5 PID: 2090 at sound/pci/hda/patch_hdmi.c:1898 check_non_pcm_per_cvt+0x41/0x50 [snd_hda_codec_hdmi]
...
[2739.684707] Call Trace:
[2739.684720] update_eld+0x121/0x5a0 [snd_hda_codec_hdmi]
[2739.684736] hdmi_present_sense+0x21e/0x3b0 [snd_hda_codec_hdmi]
[2739.684750] check_presence_and_report+0x81/0xd0 [snd_hda_codec_hdmi]
[2739.684842] intel_audio_codec_enable+0x122/0x190 [i915]
Fixes: 42b2987079 ("ALSA: hda - hdmi playback without monitor in dynamic pcm bind mode")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201013152628.920764-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case HDA controller becomes active, but codec is runtime suspended,
jack detection is not successful and no interrupt is raised. This has
been observed with multiple Realtek codecs and HDA controllers from
different vendors. Bug does not occur if both codec and controller are
active, or both are in suspend. Bug can be easily hit on desktop systems
with no built-in speaker.
The problem can be fixed by powering up the codec once after every
controller runtime resume. Even if codec goes back to suspend later, the
jack detection will continue to work. Add a flag to 'hda_codec' to
describe codecs that require this flow from the controller driver.
Modify __azx_runtime_resume() to use pm_request_resume() to make the
intent clearer.
Mark all Realtek codecs with the new forced_resume flag.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209379
Cc: Kailang Yang <kailang@realtek.com>
Co-developed-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201012102704.794423-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a HP ZCentral, the front Mic could not be detected.
The codec of the HP ZCentrol is alc671 and it needs to override the pin
configuration to enable the headset mic.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201008105645.65505-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai