Add a new PIN_CONFIG_BIAS_BUS_HOLD pin configuration for a bus holder
pin mode (also known as bus keeper, or repeater). This is a weak latch
which drives the last value on a tristate bus. Another device on the bus
can drive the bus high or low before going tristate to change the value
driven by the pin.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the drive strength pinconf to debugfs output (with the unit "mA").
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Suppress a mutex which was initialized on probe
and destroyed on remove but never used.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this patch saves the status of pinctrl registers and restore them while
resuming. this makes all drivers have coherent status for pinmux after
suspending and resuming.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrldev_list_mutex is sinked into the functions that
actually traverse the list and lock it there. The code makes
much more sense in this way. All the callers are in
non-performance critical paths and the code is way more
readable this way.
Also refactor the function get_pinctrl_dev_from_devname() to
follow the design pattern of get_pinctrl_dev_from_of_node()
which is slightly simpler.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
atlas6 is a SoC very similar with primaII, the register layput of
pinctrl is same, but the pads, groups and functions of atlas6 have
different layout with prima2, this patch
1. pull the definition of pads, groups and functions out of the
pinctrl-sirf driver,and put them into soc-specific files
2. add pads, groups and functions tables for atlas6
3. let pads, groups and functions tables become the config data of
the related dt compatible node, so the pinctrl-sirf can support
all SiRF SoCs with the config data as private data.
In this patch,we create a sirf dir, and let
the old drivers/pinctrl/pinctrl-sirf.c =
drivers/pinctrl/sirf/pinctrl-prima2.c +
drivers/pinctrl/sirf/pinctrl-sirf.c
drivers/pinctrl/sirf/pinctrl-atlas6.c is a newly created file for the
pin layout of atlas6.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace a call to deprecated devm_request_and_ioremap by devm_ioremap_resource.
Found with coccicheck and this semantic patch:
scripts/coccinelle/api/devm_ioremap_resource.cocci
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dove power management unit can mux some special functions to mpp0-15.
This patch adds support to set/get the current PMU function mapped
to the corresponding mpp pins. The device tree documentation is also
updated accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-imx6sl is in place. Enable the build of it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DT support to GPIO R-Car driver by Laurent Pinchart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NgKm
-----END PGP SIGNATURE-----
Merge tag 'renesas-gpio-rcar-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Renesas ARM based SoC GPIO R-Car updates for v3.11
DT support to GPIO R-Car driver by Laurent Pinchart.
* tag 'renesas-gpio-rcar-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (131 commits)
gpio-rcar: Add DT support
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=cph0
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Device tree patches for ux500, basically trees and auxdata:
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: drop any 0x prefix from I2C DT devices
ARM: ux500: Allocate correct amount of memory for the u8540 in DT
ARM: ux500: Provide auxdata to ux500 ASoC driver
ARM: ux500: Add DT regulators for ab8500-codec
ARM: ux500: Correct anamic2 typo in DT files
ARM: ux500: Fix trivial typo in v-anamic1 comment
ARM: ux500: Reduce PRCMU reg-names to shorter form for u8540 DT
ARM: ux500: Add an auxdata entry for MUSB for clock-name look-up
ARM: ux500: cut chip-select GPIOs from SSP device
ARM: ux500: use symbolic names for interrupt flags
ARM: ux500: use #include syntax to include *.dtsi.
ARM: ux500: bump MMC/SD max frequency for DT boots
ARM: ux500: Apply other compatible name to the u8540 DTS file
pinctrl/nomadik: Standardise Pinctrl compat string for DBx5x based platforms
ARM: ux500: Standardise Pinctrl compatible string for DBx5x based platforms
ARM: ux500: Standardise DBx5x0 based Pinctrl compat string in the DTS
crypto: ux500/hash - Enable DT probing of the driver
crypto: ux500/cryp - Enable DT probing of the driver
ARM: ux500: enable the crypto and hash on all dbx500
ARM: ux500: Provide an AUXDATA entry for ux500-hash
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds pinmux groups and functions for the two MMCIF and three
SDHI interfaces on r8a73a4 (APE6).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
From Alexander Shiyan, this is a series of cleanups of clps711x, movig it
closer to multiplatform and cleans up a bunch of old code.
* clps711x/soc:
ARM: clps711x: Update defconfig
ARM: clps711x: Add support for SYSCON driver
ARM: clps711x: edb7211: Control LCD backlight via PWM
ARM: clps711x: edb7211: Add support for I2C
ARM: clps711x: Optimize interrupt handling
ARM: clps711x: Add clocksource framework
ARM: clps711x: Replace "arch_initcall" in common code with ".init_early"
ARM: clps711x: Move specific definitions from hardware.h to boards files
ARM: clps711x: p720t: Define PLD registers as GPIOs
ARM: clps711x: autcpu12: Move remaining specific definitions to board file
ARM: clps711x: autcpu12: Special driver for handling memory is removed
ARM: clps711x: autcpu12: Add support for NOR flash
ARM: clps711x: autcpu12: Move LCD DPOT definitions to board file
ARM: clps711x: Set PLL clock to zero if we work from 13 mHz source
ARM: clps711x: Remove NEED_MACH_MEMORY_H dependency
ARM: clps711x: Re-add GPIO support
GPIO: clps711x: Add DT support
GPIO: clps711x: Rewrite driver for using generic GPIO code
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
* Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
This avoids conflicts when the USB_OVCn pins are used by another function.
This has been observed to be a problem in v3.10-rc1.
* Update CMT clock rating for sh73a0 SoC to resolve boot failure
on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oukw
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman, Renesas ARM based SoC fixes for v3.10:
- Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
This avoids conflicts when the USB_OVCn pins are used by another function.
This has been observed to be a problem in v3.10-rc1.
- Update CMT clock rating for sh73a0 SoC to resolve boot failure
on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.
* tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
sh-pfc: r8a7779: Don't group USB OVC and PENC pins
Signed-off-by: Olof Johansson <olof@lixom.net>
The list of functions selected by the MOD_SEL2 register was missing
an entry. This caused all entries after this to modify the MOD_SEL2
register incorrectly.
This bug showed up when selecting i2c2_c pins on the Renesas Hurricane board.
This bug has been present since pinmux support was added for the
r8a7779 SoC by 881023d28b ("sh-pfc: Add
r8a7779 pinmux support") in v3.8-rc4.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pinmux groups and functions for the two MMCIF and four
SDHI interfaces on r8a73a4 (APE6).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix several errors in Peripheral Function Select register tables for
r8a7790, which prevent various function pins from being correctly
configured.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
IP2[31] func2 is IRQ1A, not IRQ3A
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN DATA[0:8]/CLK/HSYNC/VSYNC pin groups to R8A7778 PFC driver.
While at it, add SH_PFC_MUX8() macro for 8-bit data busses.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
[Sergei: updated the copyrights, added SH_PFC_MUX8() macro for 8-bit data bus,
made use of SH_PFC_*() macros to define the pin groups.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No sh73a0 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh73a0 has an internal power gate on the VCCQ power supply for the
SDHI0 device that is controlled (for some strange reason) by a bit in a
PFC register. This feature should be exposed as a regulator.
As the same register is also used for pin control purposes there is no
way to achieve atomic read/write sequences with a separate regulator
driver. We thus need to implement the regulator here.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add two optional init and exit SoC operations and call them from the
core at probe and remove time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Function GPIOs have been removed, remove comments that refer to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No r8a7740 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the HDMI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the FSI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the CEU pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the GETHER
pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the BSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the INTC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the SCIF pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7740 has two LCDC units and two sets of LCDC output signals. By
default LCDC0 is routed to the LCD0 signals, and LCDC1 to the LCD1
signals. However, LCDC1 can be routed to the LCD0 signals by setting bit
MSEL6 in MSEL3CR (the LCD0 signals are further pinmuxed the usual way).
This could be configured by duplicating the LCD0 pin groups for LCDC1.
However, this would unnecessarily complicate the LCD pin groups, as no
r8a7740 board supported in mainline use such a configuration. Hardcode
the MSEL3CR MSEL6 bit to 0 for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the INTC pin groups the INTC function hasn't been added to
the functions list. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No sh7372 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
pfc-r8a7778 will have many devices pfc support in the future,
and current pfc-r8a7778 is using pin/mux definition macro for SCIF.
The device definition style using macro is readable code IMO,
but creating new macro for each devices is not good sense.
This patch adds common SH_PFC_xx() macro for each new feature devices
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN DATA[0:7]/CLK/HSYNC/VSYNC pin groups to R8A7779 PFC driver.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[horms+renesas@verge.net.au: trivial rebase on top of
"sh-pfc: r8a7779: Don't group USB OVC and PENC pins"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the RCAR_GP_PIN macro to convert from the documentation pin number
space to the linear pinctrl space.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SCIFA1 as preparation to switch to pinctrl in board files.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7790.h header.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No r8a7770 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: fixed typo in changelog: r8a7779 -> r8a7770]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make GPIO support optional for platforms that don't support GPIOLIB.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We add all necessary entries to support the external IRQs from the INTC.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial PFC support for the r8a7790 SoC.
At this point only GPIO interface is supported, move to
newer interfaces planned as incremental changes.
Original authors is Koji Matsuoka-san, thanks for him
and his team for the heavy lifting. Adjusted by Magnus
to work together with updated code in drivers/pinctrl.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@rms.renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The USB_OVCn pins are alternate options for USB over-current detection
when using a 3.3V USB interface. As they're not mandatory they can be
used independently of the USB PENC pins. Don't group the USB_OVCn and
PENC pins to avoid conflicts when the USB_OVCn pins are used by another
function.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This makes it possible to probe the COH901 pinctrl driver from
the device tree, and assigned the device tree node in the
gpio_chip so we can look up cross-references from the device
tree. Start grabbing the per-port (bank) IRQs by index instead
of by name so we don't have to look up the IRQs by name going
forward.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a simple device tree compat string for the U300 pin
controller. The base address is already passed properly as
a resource and everything works fine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinconf_dgb_config_print() takes the per-pincontroller
mutex, when what it wants to take is actually the pin maps
mutex.
Reported-by: James Hogan <james.hogan@imgtec.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix to return a negative error code from the devm_clk_get() error
handling case instead of 0, as done elsewhere in this function.
Introduced by commit 950707c0eb
(pinctrl: sunxi: add clock support)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO EINT control registers needs to be preserved across
suspend/resume cycle. This patch extends the driver to take care of
this.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch extends pin bank descriptor structure with SoC-specific
private data field that allows SoC-specific drivers to store their own
private data.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SoC-specific driver might require additional save and restore of
registers. This patch adds pair of SoC-specific callbacks per pinctrl
device to account for this.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise, we return 0 in probe error paths when gpiochip_remove() returns 0.
Also show error message if gpiochip_remove() fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support of IRQ wake-up ability configuration for
wake-up EINTs on Exynos SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO states need to be restored after s2r and this is not currently
supported in the pinctrl driver. This patch saves the gpio states before
suspend and restores them after resume.
Saving and restoring is done very early using syscore_ops and must
happen before pins are released from their powerdown state.
Patch originally from Prathyush K <prathyush.k@samsung.com> but
rewritten by Doug Anderson <dianders@chromium.org>.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The s3c24xx pins follow a similar pattern as the other Samsung SoCs and
can therefore reuse the already introduced infrastructure.
The s3c24xx SoCs have one design oddity in that the first 4 external
interrupts do not reside in the eint pending register but in the main
interrupt controller instead. We solve this by forwarding the external
interrupt from the main controller into the irq domain of the pin bank.
The masking/acking of these interrupts is handled in the same way.
Furthermore the S3C2412/2413 SoCs contain another oddity in that they
keep the same 4 eints in the main interrupt controller and eintpend
register and requiring ack operations to happen in both. This is solved
by using different compatible properties for the wakeup eint node which
set a property accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Three fixes to make the boot path for device tree work
properly on the Nomadik pin controller.
- Compile warning fix for the vt8500 driver.
- Fix error path in pinctrl-single.
- Free mappings in error path of the Lantiq controller.
- Documentation fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Kj7K
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- Three fixes to make the boot path for device tree work properly on
the Nomadik pin controller.
- Compile warning fix for the vt8500 driver.
- Fix error path in pinctrl-single.
- Free mappings in error path of the Lantiq controller.
- Documentation fixes.
* tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/lantiq: Free mapping configs for both pin and groups
pinctrl: single: fix error return code in pcs_parse_one_pinctrl_entry()
pinctrl: generic: Fix typos and clarify comments
pinctrl: vt8500: Fix incorrect data in WM8750 pinctrl table
pinctrl: abx500: Rejiggle platform data and DT initialisation
pinctrl: abx500: Specify failed sub-driver by ID instead of driver_data
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When creating mappings from DT both pin config and group config mappings
are allocated. Free them both when destroying the mappings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Introduced by commit 9dddb4df90
(pinctrl: single: support generic pinconf)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WMT_PIN_WAKEUP1 should be declared as WMT_PIN(0, 17) rather than
WMT_PIN(0, 16). This currently generates a runtime warning because
WMT_PIN_WAKEUP0 is already defined as WMT_PIN(0, 16).
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Platform Data is invariably populated for this driver, even when
booting with Device Tree. Thus the Device Tree probing code encased
within the first check for Platform Data will never executed, causing
the driver to fail when DT is enabled.
This patch fixes the aforementioned regression by rejigging the
probe() semantics to attempt to extract a platform ID from Device Tree
if one can not be sourced from platform data.
A pointer to GPIO platform data is always passed to the driver now, so
there's little point in checking for 'pdata' and executing the DT case if
it's not there. The difference between booting with DT and !DT is when
booting with DT, plat_id is not populated. Thus, in the DT case we have
to use a DT match table in order to find out which platform we're
executing on. So, we're changing the semantics here to only use the
match table if no plat_id is supplied though platform data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[edited commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a sub-driver has not been specified correctly, there is a good chance
that plat_id is NULL, hence using an attribute of plat_id in the error
message is likely to not only fail the driver but Oops the kernel. Use
the failed ID instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using the
common clock subsystem). The latter will have to get converted in one
of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot of
infrastructure in shmobile that has not been converted to DT yet. Once
those are resolved to the degree that no board specific setup code is
needed, they can get folded into the respective SoC setup files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xaLf
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
This is yet another driver change, which is split out just because
of its size. As already in 3.9, a lot of changes are going on here,
as the shmobile platform gets converted from its own pin control
API to the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9DPk
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC pinctrl changes for Renesas from Olof Johansson:
"This is yet another driver change, which is split out just because of
its size. As already in 3.9, a lot of changes are going on here, as
the shmobile platform gets converted from its own pin control API to
the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well"
* tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (142 commits)
ARM: shmobile: r8a7779: Remove INTC function GPIOs
ARM: shmobile: r8a7779: Remove LBSC function GPIOs
ARM: shmobile: r8a7779: Remove USB function GPIOs
ARM: shmobile: r8a7779: Remove HSPI function GPIOs
ARM: shmobile: r8a7779: Remove SCIF function GPIOs
ARM: shmobile: r8a7779: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7779: Remove DU function GPIOs
ARM: shmobile: r8a7779: Remove DU1_DOTCLKOUT1 GPIO
ARM: shmobile: r8a7740: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7740: Remove LCD0 and LCD1 function GPIOs
ARM: shmobile: sh73a0: Remove IrDA function GPIOs
ARM: shmobile: sh73a0: Remove USB function GPIOs
ARM: shmobile: sh73a0: Remove BSC function GPIOs
ARM: shmobile: sh73a0: Remove KEYSC function GPIOs
ARM: shmobile: sh73a0: Remove pull-up function GPIOS
ARM: shmobile: sh73a0: Remove FSI function GPIOs
ARM: shmobile: sh73a0: Remove I2C function GPIOs
ARM: shmobile: sh73a0: Remove SCIFA and SCIFB function GPIOs
ARM: shmobile: sh73a0: Remove LCDC and LCDC2 function GPIOs
ARM: shmobile: sh7372: Remove SDHI and MMCIF function GPIOs
...
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
- A quite apparent mutex fix in an untested codepath
- A compile warning fix in the plgpio driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJRgpowAAoJEEEQszewGV1z1uQP/jXY/ld+rvRkW6KB8iZgvHQG
dNNSksX84CDa75p8Dwwxpi6LlZyjq5UPbtBHSGocSPPoXs0OuLKrE42eIJIaSv4J
LQYcOKBWt/OCLLWBOh6aTGfSBMVIs5vLp3p2F38RwG7UinoVP2IlgLVA9PP7XChR
gnedpINCs5EUpf+nBLtYOUBljmOiwJZg9ZfL40yJE6Guiw3oamm3eg/dpmwGbi8I
2yFY9Qt7kDA/UNW0y+wFc6wdV3kvVQt7U4nnWYNEZZENnFoDGUOgwEr7T90EReQD
uivmctQ3orVqLFMdPwxrxgJP5ZKlg3ZO8nVVohwSbWV78oarvh9JhInA5I5JU7OV
5DF485DQ8k932jmfhK8g+geR0+siW60cQ7i0bPgHUePa15I5ck/c/SztVO0HiDX5
j+/VMEH2mEQPId0XW3hZergXQmK6jiQTN+Ly48GsAsztZYPZ964x8ikxAZw/oIAF
ri8I18KteanHNaw0G1BdXqGkWMh5SzzZ0+JoSYEH7uGbATNZPd3cchJmmPly89m9
butJUr4pfP7mu2zpzsGT9IjOTbvDir2O+i/9+GU2n45VWl8NSzgtXHJNCsYdtX1I
zJNp47pL6uGfjafAxh/lpvhOlXaDRNu1+d8WzCepA3r5RyZugXdABjM6pbVJSP0G
V8oruhqy09mELcexm5DO
=kX7M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Two fixes to the pinctrl subsystem for v3.10:
- A quite apparent mutex fix in an untested codepath
- A compile warning fix in the plgpio driver"
* tag 'pinctrl-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix mutex deadlock in get_pinctrl_dev_from_of_node()
pinctrl: plgpio: add CONFIG_PM_SLEEP to suspend/resume functions
More multiplatform enablement for ARM platforms. The ones converted in
this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was a
patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4hSo
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform updates from Olof Johansson:
"More multiplatform enablement for ARM platforms. The ones converted
in this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was
a patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then"
* tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms
clocksource: nomadik-mtu: fix up clocksource/timer
Revert "ARM: exynos: enable multiplatform support"
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: exynos: enable multiplatform support
rtc: s3c: make header file local
mtd: onenand/samsung: make regs-onenand.h file local
thermal/exynos: remove unnecessary header inclusions
mmc: sdhci-s3c: remove platform dependencies
ARM: samsung: move mfc device definition to s5p-dev-mfc.c
ARM: exynos: move debug-macro.S to include/debug/
ARM: exynos: prepare for sparse IRQ
ARM: exynos: introduce EXYNOS_ATAGS symbol
ARM: tegra: build assembly files with -march=armv7-a
ARM: Push selects for TWD/SCU into machine entries
ARM: ux500: build hotplug.o for ARMv7-a
ARM: ux500: move to multiplatform
ARM: ux500: make remaining headers local
ARM: ux500: make irqs.h local to platform
ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
...
Device-tree updates for 3.10. The bulk of the churn in this branch is due
to i.MX moving from C-defined pin control over to device tree, which is
a one-time conversion that will allow greater flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8X1b
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree updates from Olof Johansson:
"Part 1 of device-tree updates for 3.10. The bulk of the churn in this
branch is due to i.MX moving from C-defined pin control over to device
tree, which is a one-time conversion that will allow greater
flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (113 commits)
arm: mvebu: PCIe Device Tree informations for Armada XP GP
arm: mvebu: PCIe Device Tree informations for Armada 370 DB
arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
arm: mvebu: PCIe Device Tree informations for Armada XP DB
arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
arm: mvebu: add PCIe Device Tree informations for Armada XP
arm: mvebu: add PCIe Device Tree informations for Armada 370
ARM: sunxi: unify osc24M_fixed and osc24M
arm: vt8500: Add SDHC support to WM8505 DT
ARM: dts: Add a 64 bits version of the skeleton device tree
ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
ARM: dts: imx6dl-wandboard: Add USB Host support
ARM: dts: imx51 cpu node
ARM: dts: Add missing imx27-phytec-phycore dtb target
ARM: dts: Add NFC support for i.MX27 Phytec PCM038 module
ARM: i.MX51: Add PATA support
ARM: dts: Add initial support for Wandboard Dual-Lite
...
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
This obvious bug was introduced by d755910b7 ("pinctrl: move subsystem
mutex to pinctrl_dev struct").
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/pinctrl/spear/pinctrl-plgpio.c:645:12: warning: 'plgpio_suspend' defined but not used [-Wunused-function]
drivers/pinctrl/spear/pinctrl-plgpio.c:684:12: warning: 'plgpio_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This mutex avoids deadlock in case of use of multiple pin
controllers. Before this modification, by using a global
mutex, deadlock appeared when, for example, a call to
pinctrl_pins_show() locked the pinctrl_mutex, called the
ops->pin_dbg_show of a particular pin controller. If this
pin controller needs I2C access to retrieve configuration
information and I2C driver is using pinctrl to drive its
pins, a call to pinctrl_select_state() try to lock again
pinctrl_mutex which leads to a deadlock.
Notice that the mutex grab from the two direction functions
was moved into pinctrl_gpio_direction().
For several cases, we can't replace pinctrl_mutex by
pctldev->mutex, because at this stage, pctldev is
not accessible :
- pinctrl_get()/pinctrl_put()
- pinctrl_register_maps()
So add respectively pinctrl_list_mutex and
pinctrl_maps_mutex in order to protect
pinctrl_list and pinctrl_maps list instead.
Reintroduce pinctrldev_list_mutex in
find_pinctrl_by_of_node(),
pinctrl_find_and_add_gpio_range()
pinctrl_request_gpio(), pinctrl_free_gpio(),
pinctrl_gpio_direction(), pinctrl_devices_show(),
pinctrl_register() and pinctrl_unregister() to
protect pinctrldev_list.
Changes v2->v3:
- Fix a missing EXPORT_SYMBOL_GPL() for pinctrl_select_state().
Changes v1->v2:
- pinctrl_select_state_locked() is removed, all lock mechanism
is located inside pinctrl_select_state(). When parsing
the state->setting list, take the per-pin-controller driver
lock. (Patrice).
- Introduce pinctrldev_list_mutex to protect pinctrldev_list
in all functions which parse or modify pictrldev_list.
(Patrice).
- move find_pinctrl_by_of_node() from pinctrl/devicetree.c to
pinctrl/core.c in order to protect pinctrldev_list.
(Patrice).
- Sink mutex:es into some functions and remove some _locked
variants down to where the lists are actually accessed to
make things simpler. (Linus)
- Drop *all* mutexes completely from pinctrl_lookup_state()
and pinctrl_select_state() - no relevant mutex was taken
and it was unclear what this was protecting against. (Linus)
Reported by : Seraphin Bonnaffe <seraphin.bonnaffe@stericsson.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This update contains a basic fix that went unseen through
test and review.
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit de88cbb7 moved definitions of chained_irq_enter and
chained_irq_exit to a generic header, which must be now included instead
of the legacy arch-specific one.
This patch fixes build error caused by including the legacy header
leading to undefined chained_irq_enter and chained_irq_exit symbols.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register() returns NULL on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This update adds a debugfs interface to modify a pin configuration
for a given state in the pinctrl map. This allows to modify the
configuration for a non-active state, typically sleep state.
This configuration is not applied right away, but only when the state
will be entered.
This solution is mandated for us by HW validation: in order
to test and verify several pin configurations during sleep without
recompiling the software.
Change log in this patch set;
Take into account latest feedback from Stephen Warren:
- stale comments update
- improved code efficiency and readibility
- limit size of global variable pinconf_dbg_conf
- remove req_type as it can easily be added later when
add/delete requests support is implemented
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix an issue when probing pinctrl-abx500 with no
platform data.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Correct a typo in sh-pfc r8a7779
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0Xk/
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinmux-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
From Simon Horman:
Renesas ARM and SH based SoC pinmux fixes for v3.10
Correct a typo in sh-pfc r8a7779
* tag 'renesas-pinmux-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
sh-pfc: r8a7779: tidyup intc_irq3_b typo
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a pinctrl driver for i.MX6 SoloLite based on pinctrl-imx core
driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The imx6dl is a derivative of imx6q with very limited difference. These
two SoCs are so compatible that they can be handled as one platform in
software. That said, we will not have target SOC_IMX6DL but just
reusing SOC_IMX6Q. That's why the pinctrl-imx6dl driver is added here
with symbol PINCTRL_IMX6Q controlling the build of it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Currently, all imx pinctrl drivers maintain a big array of struct
imx_pin_reg which hard-codes data like register offset and mux mode
setting for each pin function. Every time a new imx SoC support is
added, we need to add such a big mount of data. With moving to single
kernel build, it's only matter of time to be blamed on memory consuming.
With DTC pre-processor support in place, the patch moves all these data
into device tree by redefining the PIN_FUNC_ID in imxXX-pinfunc.h and
changing the PIN_FUNC_ID parsing code a little bit.
The pin id gets re-numbered based on mux register offset, or config
register offset if the pin has no mux register, so that kernel can
identify the pin id from register offsets provided by device tree.
As a bonus point of the change, those arbitrary magic numbers standing
for particular PIN_FUNC_ID in device tree sources are now replaced by
macros to improve the readability of dts files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into next/cleanup
This is a dependency for the mxs/cleanup branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pin functions associated to the ethernet controller were introduced
with the label "wemac", which was the name of the ethernet driver in the
allwinner source tree, while the real name of the IP is actually "emac",
as advertised in several documents including the datasheet.
Since this is part of the device tree bindings, and that these part of
the bindings have not yet be released in a kernel version, it seems like
the good timing to change it and assure consistency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Exynos5440 supports gpio interrupts on gpios 16 to 23. The eight interrupt lines
originating from the pin-controller are connected to the gic. Add irq-chip support
for these interrupts.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The property 'samsung,exynos5440-pins' is optional in configuration nodes
which are included in the Exynos5440 pin-controller device node. Fix the
incorrect failure in driver probe if 'samsung,exynos5440-pins' property
is not found in the configuration nodes.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Silences the following warnings:
drivers/pinctrl/pinctrl-ab8505.c:274:28: warning:
symbol 'ab8505_alternate_functions' was not declared. Should it be static?
drivers/pinctrl/pinctrl-ab8505.c:351:32: warning:
symbol 'ab8505_gpio_irq_cluster' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Silences the following warnings:
drivers/pinctrl/pinctrl-ab8540.c:302:28: warning:
symbol 'ab8540_alternate_functions' was not declared. Should it be static?
drivers/pinctrl/pinctrl-ab8540.c:379:32: warning:
symbol 'ab8540_gpio_irq_cluster' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following warnings:
drivers/pinctrl/pinctrl-ab9540.c:382:28: warning:
symbol 'ab9540alternate_functions' was not declared. Should it be static?
drivers/pinctrl/pinctrl-ab9540.c:457:32: warning:
symbol 'ab9540_gpio_irq_cluster' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These symbols are used only in this file. Silences the following
warnings:
drivers/pinctrl/pinctrl-ab8500.c:392:28: warning:
symbol 'ab8500_alternate_functions' was not declared. Should it be static?
drivers/pinctrl/pinctrl-ab8500.c:458:32: warning:
symbol 'ab8500_gpio_irq_cluster' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These symbols are used only in this file. Without this patch
we get the following warnings:
drivers/pinctrl/pinctrl-abx500.c:520:5: warning:
symbol 'abx500_gpio_request' was not declared. Should it be static?
drivers/pinctrl/pinctrl-abx500.c:527:6: warning:
symbol 'abx500_gpio_free' was not declared. Should it be static?
drivers/pinctrl/pinctrl-abx500.c:614:5: warning:
symbol 'abx500_gpio_request_enable' was not declared. Should it be static?
drivers/pinctrl/pinctrl-abx500.c:714:5: warning:
symbol 'abx500_pin_config_get' was not declared. Should it be static?
drivers/pinctrl/pinctrl-abx500.c:721:5: warning:
symbol 'abx500_pin_config_set' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl-s3c64xx driver which implements pin control
interface for Samsung S3C64xx SoCs.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for banks that have more than one function
configuration registers, e.g. some of the banks of S3C64xx SoCs.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch replaces statically hardcoded register offsets of Exynos SoCs
with an array of register offsets in samsung_pin_bank_type struct.
Thanks to this change, support for SoCs with other set and order of
registers can be added (e.g. S3C24xx and S3C64xx).
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch splits pin bank description into two structures, one
describing bank type (currently only bitfield widths), which can be
shared across multiple banks and second containing bank-specific
parameters including a pointer to a bank type struct.
It is a prerequisite for further patch removing the statically hardcoded
register offsets, making it impossible to support SoCs with different
set and order of pin control registers.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since pinctrl-samsung is a common part of the pin control support for
several Samsung SoCs, it can be compiled without Exynos support enabled.
This patch surrounds Exynos-specific driver data with ifdefs to include
them only when support for Exynos is enabled.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
[Fixed up EXYNOS4->EXYNOS]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain pin control registers can be accessed from different contexts,
i.e. pinctrl, gpio and irq functions. This makes the locking provided by
pin control core insufficient.
This patch adds necessary locking using a per bank spinlock as it was
done in the old Samsung GPIO driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This series consists mainly of clean-ups for clockevents and
clocksource timers on OMAP2+ devices. The most significant change
in functionality comes from the 5th patch which is changing the
selection of the clocksource timer for OMAP3 and AM335x devices
when gptimers are used for clocksource.
Note that this series depends on 7185684 (ARM: OMAP: use
consistent error checking) in RMK's tree and 960cba6 (ARM:
OMAP5: timer: Update the clocksource name as per clock data)
in omap-for-v3.10/fixes-non-critical. So this branch is based
on a merge of 7185684 and omap-for-v3.10/fixes-non-critical
to avoid non-trivial merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5kiA
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
From Tony Lindgren <tony@atomide.com>:
Clean-up for omap2+ timers from Jon Hunter <jon-hunter@ti.com>:
This series consists mainly of clean-ups for clockevents and
clocksource timers on OMAP2+ devices. The most significant change
in functionality comes from the 5th patch which is changing the
selection of the clocksource timer for OMAP3 and AM335x devices
when gptimers are used for clocksource.
Note that this series depends on 7185684 (ARM: OMAP: use
consistent error checking) in RMK's tree and 960cba6 (ARM:
OMAP5: timer: Update the clocksource name as per clock data)
in omap-for-v3.10/fixes-non-critical. So this branch is based
on a merge of 7185684 and omap-for-v3.10/fixes-non-critical
to avoid non-trivial merge conflicts.
* tag 'omap-for-v3.10/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: Fix sparse warning in system timers
ARM: OMAP2+: Store ID of system timers in timer structure
ARM: OMAP3: Update clocksource timer selection
ARM: OMAP2+: Simplify system timers definitions
ARM: OMAP2+: Simplify system timer clock definitions
ARM: OMAP2+: Remove hard-coded test on timer ID
ARM: OMAP2+: Display correct system timer name
ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
ARM: OMAP: dpll: enable bypass clock only when attempting dpll bypass
ARM: OMAP2+: powerdomain: avoid testing whether an unsigned char is less than 0
ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
ARM: OMAP2+: am335x: Change the wdt1 func clk src to per_32k clk
ARM: OMAP2+: AM33xx: hwmod: Add missing sysc definition to wdt1 entry
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
James Hogan