The relation of i2s nodes as follows:
i2s_src 0 0 594000000 0
i2s_frac 0 0 11289600 0
i2s_pre 0 0 11289600 0
sclk_i2s0 0 0 11289600 0
i2s0_clkout 0 0 11289600 0
hclk_i2s0 1 1 99000000 0
sclk_i2s0 is the master clock, when to set rate of sclk_i2s0, should
allow to set its parent's rate, by add flag CLK_SET_RATE_PARENT for
"i2s_frac", "i2s_pre", "i2s0_clkout" and "sclk_i2s0".
Tested on rk3288 board using max98090, with command "aplay <music.wav>"
Change-Id: I12faad082566532b65a7de8c0a6845e1c17870e6
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the necessary soc-specific divider values and switches the armclk
to use the newly introduced cpuclk type.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
When changing the armclk on Rockchip SoCs it is supposed to be reparented
to an alternate parent before changing the underlying pll and back after
the change. Additionally there exist clocks that are very tightly bound to
the armclk whose divider values are set according to the armclk rate.
Add a special clock-type to handle all that. The rate table and divider
values will be supplied from the soc-specific clock controllers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
On a rk3288-board:
Tested-by: Doug Anderson <dianders@chromium.org>
Rockchip SoCs contain clocks tightly bound to the armclk, where the best
rate / divider is supplied by the vendor after careful measuring.
Often this ideal rate may be greater than the current rate.
Therefore prevent the ccf from trying to set these dividers itself by
setting them to read-only.
In the case of the rk3066, this also includes the aclk_cpu, which makes it
necessary to also split its direct child-clocks (pclk_cpu, hclk_cpu, ...)
into individual definitions for rk3066 and rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
aclk_cpu_pre on the rk3188 can either be sourced from the armclk or the gpll.
To reduce complexity on apll changes caused by cpufreq, reparent it always
to the gpll source.
If really necessary it could be reparented back on a per board level using
the assigned-clocks mechanism.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In RK3288, APLL lock status bit is in GRF_SOC_STATUS1,
but in RK3188, is GRFSOC_STATUS0.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Also name the constant accordingly as GRF_SOC_STATUS1
to prevent confusion.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
The register providing the pll lock status is at a different address on the
rk3066. The error became apparent while working on cpufreq support for
the rockchip SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Rockchip PLL code switches into slow mode (AKA bypass more AKA
24MHz mode) before actually changing the PLL. This keeps anyone from
using the PLL while it's changing. However, in all known Rockchip
SoCs nobody should ever see the 24MHz when changing the PLL supplying
the armclk because we should reparent children to an alternate
(faster than 24MHz) PLL.
One problem is that the code to switch to an alternate parent was
running in PRE_RATE_CHANGE. ...and the code to switch to slow mode
was _also_ running in PRE_RATE_CHANGE. That meant there was no real
guarantee that we would switch to an alternate parent before switching
to 24MHz mode.
Let's move the switch to "slow mode" straight into
rockchip_rk3066_pll_set_rate(). That means we're guaranteed that the
24MHz is really a last-resort.
Note that without this change on real systems we were the code to
switch to an alternate parent at 24MHz. In some older versions of
that code we'd appy a (temporary) / 5 to the 24MHz causing us to run
at 4.8MHz. That wasn't enough to service USB interrupts in some cases
and could lead to a system hang.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Implementing a restart handler in a module don't make sense as there would
be no guarantee that the module is loaded when a restart is needed.
Unexport arm_pm_restart to ensure that no one gets the idea to do it
anyway.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart. Register
with it instead of setting arm_pm_restart.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart. Register
with it to restart the system instead of misusing the reboot notifier.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel now provides an API to trigger a system restart. Register with
it instead of setting arm_pm_restart.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now supports a restart handler call chain for system
restart functions.
With this change, the arm_pm_restart callback is now optional, so drop its
initialization and check if it is set before calling it. Only call the
kernel restart handler if arm_pm_restart is not set.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now supports a restart handler call chain to restart the
system. Call it if arm_pm_restart is not set.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
machine_restart is supported on non-ARM platforms, and and ultimately
calls arm_pm_restart, so dont call arm_pm_restart directly but use the
more generic function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Various drivers implement architecture and/or device specific means to
restart (reset) the system. Various mechanisms have been implemented to
support those schemes. The best known mechanism is arm_pm_restart, which
is a function pointer to be set either from platform specific code or from
drivers. Another mechanism is to use hardware watchdogs to issue a reset;
this mechanism is used if there is no other method available to reset a
board or system. Two examples are alim7101_wdt, which currently uses the
reboot notifier to trigger a reset, and moxart_wdt, which registers the
arm_pm_restart function.
The existing mechanisms have a number of drawbacks. Typically only one
scheme to restart the system is supported (at least if arm_pm_restart is
used). At least in theory there can be multiple means to restart the
system, some of which may be less desirable (for example one mechanism may
only reset the CPU, while another may reset the entire system). Using
arm_pm_restart can also be racy if the function pointer is set from a
driver, as the driver may be in the process of being unloaded when
arm_pm_restart is called. Using the reboot notifier is always racy, as it
is unknown if and when other functions using the reboot notifier have
completed execution by the time the watchdog fires.
Introduce a system restart handler call chain to solve the described
problems. This call chain is expected to be executed from the
architecture specific machine_restart() function. Drivers providing
system restart functionality (such as the watchdog drivers mentioned
above) are expected to register with this call chain. By using the
priority field in the notifier block, callers can control restart handler
execution sequence and thus ensure that the restart handler with the
optimal restart capabilities for a given system is called first.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If CONFIG_COMMON_CLK is selected then __clk_get and __clk_put are
defined in drivers/clk/clk.c and declared in include/linux/clkdev.h.
Sylwester's series[0] to properly support clk_{get,put} in the common
clock framework made changes to the asm-specific clkdev.h headers, but
not the asm-generic version. Tomeu's recent changes[1] to introduce a
provider/consumer split in the clock framework uncovered this problem,
causing the following build error on any architecture using the
asm-generic clkdev.h (e.g. x86 architecture and the ACPI LPSS driver):
In file included from drivers/acpi/acpi_lpss.c:15:0:
include/linux/clkdev.h:59:5: error: conflicting types for ‘__clk_get’
int __clk_get(struct clk_core *clk);
^
In file included from arch/x86/include/generated/asm/clkdev.h:1:0,
from include/linux/clkdev.h:15,
from drivers/acpi/acpi_lpss.c:15:
include/asm-generic/clkdev.h:20:19: note: previous definition of ‘__clk_get’ was here
static inline int __clk_get(struct clk *clk) { return 1; }
^
Fixed by only declarating __clk_get and __clk_put when
CONFIG_COMMON_CLK is set.
[0] http://lkml.kernel.org/r/<1386177127-2894-5-git-send-email-s.nawrocki@samsung.com>
[1] http://lkml.kernel.org/r/<1409758148-20104-1-git-send-email-tomeu.vizoso@collabora.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch add the clock node in PD_VIDEO
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch use the new defined clock ID to initial the clock nodes.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch add some clock binding id for different modules
that under development and going to send upstream.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The npll on rk3288 is exactly the same pll type as the other 4. Yet it
was missing the link to the rate table, making rate changes impossible.
Change that by setting the table.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The rk3288 actually has 12 softresets, so fix the register count.
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The patch add the rest of the indices of the additional reset
registers from the updated TRM.
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The dwc2 usb controller also uses agressive clock gating, which in this
case leads to hclk_peri getting disabled and hanging the system.
Therefore move it to the critical clocks until we also control that
part of the system.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
On 32bit architectures, like ARM calculating the fractional rate will
do the multiplication before converting the value to u64 when it gets
assigned to ret, which can produce overflows.
The error in question happened with a parent_rate of 386MHz, m = 3000,
n = 60000, which resulted in a wrong rate value of 15812Hz.
Therefore cast parent_rate to u64 to make sure the multiplication
happens in a 64bit space and produces the correct 192MHz in the example.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add Device Tree binding documentation for the clocks
outputs in the Maxim 77802 Power Management IC.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The MAX77802 PMIC has two 32.768kHz Buffered Clock Outputs with
Low Jitter Mode. This patch adds support for these two clocks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Like most clock drivers, the Maxim 77686 PMIC clock binding
follows the convention that the "#clock-cells" property is
used to specify the number of cells in a clock provider.
But the binding document is not clear enough that it shall
be set to 1 since the PMIC support multiple clocks outputs.
Also, explain that the clocks identifiers are defined in a
header file that can be included by Device Tree source with
client nodes to avoid using magic numbers.
Finally, add "clock-output-names" as an optional property
since now is supported by the clock driver.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Clocks drivers for Maxim PMIC are very similar so they can
be converted to use the generic Maxim clock driver.
Also, while being there use module_platform_driver() helper
macro to eliminate more boilerplate code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Maxim Integrated Power Management ICs are very similar with
regard to their clock outputs. Most of the clock drivers for
these chips are duplicating code and are simpler enough that
can be converted to use a generic driver to consolidate code
and avoid duplication.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a dt-binding include for Maxim 77686
PMIC clock IDs that can be used by both the max77686
clock driver and Device Tree source files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since commit 54196ccbe0 (of: consolidate linker section OF match table
declarations) which went into 3.16-rc1 the following compiler warning is
generated:
In file included from drivers/clk/clk-efm32gg.c:12:0: include/linux/of.h:772:20:
warning: comparison of distinct pointer types lacks a cast [enabled by default]
.data = (fn == (fn_type)NULL) ? fn : fn }
^
include/linux/of.h:785:3: note: in expansion of macro '_OF_DECLARE'
_OF_DECLARE(table, name, compat, fn, of_init_fn_1)
^
include/linux/clk-provider.h:545:42: note: in expansion of macro 'OF_DECLARE_1'
#define CLK_OF_DECLARE(name, compat, fn) OF_DECLARE_1(clk, name, compat, fn)
^
drivers/clk/clk-efm32gg.c:81:1: note: in expansion of macro 'CLK_OF_DECLARE'
CLK_OF_DECLARE(efm32ggcmu, "efm32gg,cmu", efm32gg_cmu_init);
^
Fix it by making efm32gg_cmu_init return void.
Cc: Rob Herring <robh@kernel.org>
Reported-by: Bryan Hundven <bryanhundven@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use __initconst instead of __initdata for constant init data.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As checkpatch suggests:
WARNING: Possible unnecessary 'out of memory' message,
remove an error message after failing kmalloc() from the PLL driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In some cases, clocks can switch their parent with clk_set_rate, for
example clk_mux can do this in some cases. Current implementation of
clk_change_rate uses un-safe list iteration on the clock children, which
will cause wrong clocks to be parsed in case any of the clock children
change their parents during the change rate operation. Fixed by using
the safe list iterator instead.
The problem was detected due to some divide by zero errors generated
by clock init on dra7-evm board, see discussion under
http://article.gmane.org/gmane.linux.ports.arm.kernel/349180 for details.
Fixes: 71472c0c06 ("clk: add support for clock reparent on set_rate")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clocks for i2c1 and i2c2 are flipped. The clock tree matched the
Technical Reference Manual (TRM) but the TRM was wrong. Swap them in
the clock tree. This was determined experimentally (by Addy) and
confirmed by the Rockchip IC team.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reported-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The pre-divider for the sdc clocks only has 2 bits in it, so we
can't possibly divide by anything larger than 4 here.
Furthermore, we program the value of ~(n - m) and the n value is
larger than 8 bits (max of 256). Replace this entry with 200kHz
which is close enough to 144kHz to be usable.
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Fixes: 24d8fba44a "clk: qcom: Add support for IPQ8064's global clock controller (GCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Test rate value before calculating the div value to avoid div by zero.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The RM9200 USB clock is actually connected to a single parent (the PLLB)
on which we can apply a specific divider.
The USB clock divider does not allow for fine grained control on the USB
clock frequency, hence propagating the set_rate request to the parent is
the only choice we have to properly configure the USB clock rate.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use the cached values to calculate PLL rate instead of the register values.
This is required to prevent erroneous PLL rate return when the PLL rate
has been configured but the PLL is not prepared yet.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Heiko Stuebner