Commit Graph

973 Commits

Author SHA1 Message Date
Andy Shevchenko 525667c025 serial: 8250_of: Use of_device_get_match_data()
Use of_device_get_match_data() to simplify the code a bit.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 12:12:02 +02:00
Linus Torvalds 055128ee00 dmaengine updates for v5.2-rc1
- Updates to stm32 dma residue calculations
  - Interleave dma capability to axi-dmac and
    support for ZynqMP arch
  - Rework of channel assignment for rcar dma
  - Debugfs for pl330 driver
  - Support for Tegra186/Tegra194, refactoring for new chips
    and support for pause/resume
  - Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
    rcar-dmac, stm32-dma etc
  - dev_get_drvdata() updates on few drivers
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJc08p1AAoJEHwUBw8lI4NHD14QAJGU7MOc9dpr+qtm2k3sNO3o
 EXZtb3GjTs4MUt6EfMA47KXsxeq4UhubQqM7CmPngDyjXaPd4JBE8bwAd+OzS9sq
 eAPMa+M1g8MehuQcdUzB/y6APoSFhGvFoGLY8e7FeI6fwYNm3Yy2gTSiZfpMb3MW
 hclJQe+UWfppUHOig13tr0tbQ31DOa7qb2+roVJqDEb9sQ5bDkhRWXjElfoeSXsS
 n8nNh4GZr5RkIxfzslVRZNfqb1lja2e03SXBsN9faQI7BfIYBM+9hWSYd4Nq8uYo
 xvhYf9gJnKVKtFrwdXtyeBJ80DijWBoodhLrLOfhEYYOrCl9WwJT9AepIOdvij32
 11FwjCbkC9ASQ1cSLyRUBbdmfykSlBvdbAMwJc1y9qK7k9BMba3rXRJfimlRy29A
 Cpsu4tZKoPlZRGinoGnEGreg1YZI1YHwa+hlkW/8V9Zkb2hvIUbbXr7xHedJf7n4
 gIb5DnCF5pC1umB/o7pj2YXrYBc9GETp3sDQ88aw1owKh1T2pZcc5HOpi4p7/7n+
 b2HM0cWOCM3aKwdOcONk0jd87FcYQm3g1isQF5SCOtOys8Uy6wNqo9aRrfE/94aw
 4SiGRq9/nSOHDh72mD3Ux7v47/cFjWGzZZJVy5+NC+Mq79KxgpXOjsIr7YVbcn9m
 GuUdiDZmUvZ4y+qq/uCI
 =JDU6
 -----END PGP SIGNATURE-----

Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:

 - Updates to stm32 dma residue calculations

 - Interleave dma capability to axi-dmac and support for ZynqMP arch

 - Rework of channel assignment for rcar dma

 - Debugfs for pl330 driver

 - Support for Tegra186/Tegra194, refactoring for new chips and support
   for pause/resume

 - Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
   stm32-dma etc

 - dev_get_drvdata() updates on few drivers

* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
  dmaengine: tegra210-adma: restore channel status
  dmaengine: tegra210-dma: free dma controller in remove()
  dmaengine: tegra210-adma: add pause/resume support
  dmaengine: tegra210-adma: add support for Tegra186/Tegra194
  Documentation: DT: Add compatibility binding for Tegra186
  dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
  dmaengine: at_xdmac: remove a stray bottom half unlock
  dmaengine: fsl-edma: Adjust indentation
  dmaengine: fsl-edma: Fix typo in Vybrid name
  dmaengine: stm32-dma: fix residue calculation in stm32-dma
  dmaengine: nbpfaxi: Use dev_get_drvdata()
  dmaengine: bcm-sba-raid: Use dev_get_drvdata()
  dmaengine: stm32-dma: Fix unsigned variable compared with zero
  dmaengine: stm32-dma: use platform_get_irq()
  dmaengine: rcar-dmac: Update copyright information
  dmaengine: imx-sdma: Only check ratio on parts that support 1:1
  dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
  dmaengine: idma64: Move driver name to the header
  dmaengine: bcm2835: Drop duplicate capability setting.
  dmaengine: pl330: _stop: clear interrupt status
  ...
2019-05-09 08:51:45 -07:00
Long Cheng bdbd0a7f8f serial: 8250-mtk: modify baudrate setting
In termios function, add Fractional divider to adjust baudrate.

Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:37:42 +02:00
Long Cheng 8ceeb47098 serial: 8250-mtk: add follow control
Add SW and HW follow control function.

Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:37:42 +02:00
Su Bao Cheng 3e51ceea10 serial: 8250_exar: Adjust IOT2000 matching
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.

As only the IOT2040 variants have the Exar chip on board, matching on
their board name is enough. In the future there will be no other devices
with the "SIMATIC IOT2000" DMI board name but different hardware.

Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:37:41 +02:00
Greg Kroah-Hartman f16aa97d3f tty: fix up a few remaining files without SPDX identifiers
There were a few straggling files under drivers/tty/ that did not have
any SPDX identifier either because they entered the tree recently, or
they somehow missed the mass-tagging of commit b24413180f ("License
cleanup: add SPDX GPL-2.0 license identifier to files with no license")

This commit follows the same rule as b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license") where files
without any specified license in them fall under GPL-2.0 as the correct
license for the individual file.  Add that identifier to these remaining
files so that we don't have to guess at the license of them in the
future.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-04 18:48:43 +02:00
Greg Kroah-Hartman 38c91d1d55 tty: add SPDX identifiers to Kconfig and Makefiles
There were a few Kconfig and Makefiles under drivers/tty/ that were
missing a SPDX identifier.  Fix that up so that automated tools can
properly classify all kernel source files.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-04 18:48:43 +02:00
YueHaibing 9828def35a serial: 8250_fintek: Make fintek_8250_set_termios static
Fix sparse warning:

drivers/tty/serial/8250/8250_fintek.c:306:6: warning:
 symbol 'fintek_8250_set_termios' was not declared. Should it be static?

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28 00:29:03 +09:00
Andy Shevchenko 5ba846b1ee dmaengine: idma64: Use actual device for DMA transfers
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.

In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.

We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2019-03-21 19:48:26 +05:30
Linus Torvalds 31ef489a02 dmaengine updates for v5.1-rc1
- dmatest updates for modularizing common struct and code
  - remove SG support for VDMA xilinx IP and updates to driver
  - Update to dw driver to support Intel iDMA controllers
    multi-block support
  - tegra updates for proper reporting of residue
  - Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
  - struct_size() usage and useless LIST_HEAD cleanups in subsystem.
  - qDMA controller driver for Layerscape SoCs
  - stm32-dma PM Runtime support
  - And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
    bcm2835, qcom_hidma etc
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJciVhkAAoJEHwUBw8lI4NHdVoQANDfaY1eruozJobfWX0w1b8U
 0eSCN4M/gRzL/K1nOTWTV9dZFGycGokPBn25lryX6d6VIL+yO7Ptpwls/w0inn0e
 RgVtESQodLZyxcD4iWACVfTGxqxe74/bXCRAq0OCrjt5oX+5KdsBsTrhHvB8dQin
 JWT7Mq6tii5wZHZHl9b4Ds/crxM9+pIHmlzbu5MQiPDL37X9HX4KUoLQCKrVGgZt
 3FjlKEiSS6CnBWP1cs/aHgANr/PjOIwL8SD1t5NPS3i7/2k9z1u16TmmI8SbcyHf
 y9hVy1QPlxC5V85EPYK7JW7JLILotkMToxlX/QhfaFN0PWQq04rp6PCLvObKJuB2
 36QJTwSXBM2/f9bWwkddPyo9Szb3L30K80Vx8zlxzgoXYWtFFB2BXAV57M/I48j2
 gMnxEMZpHD3IupeqlykCmssClVVmCRT8qUZHLNHTdDNu48rLuNlZestFGyBS2Ma2
 D4UcJPiA/IxENy1rz54XoCajL/BIJOsFXXVRikjj3vfbV0Uir0uB9puzwfemMtKz
 tCrJbKwnnDtN30vBZtU7hVu/t4lFYYnl2c945+SpeQC69dysz3IFQGem0kxVHKnH
 INdQH4Od7nQbVQer1EXg4+h3n/rUbcYx/0iLE6JAYyOT80wE+KSlrQ5etqyJ3/qh
 1BxvU49PkUUPzw7aUGgS
 =Ykvn
 -----END PGP SIGNATURE-----

Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:

 - dmatest updates for modularizing common struct and code

 - remove SG support for VDMA xilinx IP and updates to driver

 - Update to dw driver to support Intel iDMA controllers multi-block
   support

 - tegra updates for proper reporting of residue

 - Add Snow Ridge ioatdma device id and support for IOATDMA v3.4

 - struct_size() usage and useless LIST_HEAD cleanups in subsystem.

 - qDMA controller driver for Layerscape SoCs

 - stm32-dma PM Runtime support

 - And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
   bcm2835, qcom_hidma etc

* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
  dmaengine: imx-sdma: fix consistent dma test failures
  dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
  dmaengine: imx-sdma: add clock ratio 1:1 check
  dmaengine: dmatest: move test data alloc & free into functions
  dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
  dmaengine: dmatest: wrap src & dst data into a struct
  dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
  dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
  dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
  dmaengine: ioatdma: Add Snow Ridge ioatdma device id
  dmaengine: sprd: Change channel id to slave id for DMA cell specifier
  dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
  dmaengine: mv_xor: Use correct device for DMA API
  Documentation :dmaengine: clarify DMA desc. pointer after submission
  Documentation: dmaengine: fix dmatest.rst warning
  dmaengine: k3dma: Add support for dma-channel-mask
  dmaengine: k3dma: Delete axi_config
  dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
  Documentation: bindings: dma: Add binding for dma-channel-mask
  Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
  ...
2019-03-14 09:11:54 -07:00
Lubomir Rintel f4817843e3 serial: 8250_of: assume reg-shift of 2 for mrvl,mmp-uart
There are two other drivers that bind to mrvl,mmp-uart and both of them
assume register shift of 2 bits. There are device trees that lack the
property and rely on that assumption.

If this driver wins the race to bind to those devices, it should behave
the same as the older deprecated driver.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-26 12:30:45 +01:00
Lubomir Rintel fe9ed6d248 serial: 8250_pxa: honor the port number from devicetree
Like the other OF-enabled drivers, use the port number from the firmware if
the devicetree specifies an alias:

  aliases {
      ...
      serial2 = &uart2; /* Should be ttyS2 */
  }

This is how the deprecated pxa.c driver behaved, switching to 8250_pxa
messes up the numbering.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-26 12:30:44 +01:00
Jay Dolan 78d3820b9b serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()
The four port Pericom chips have the fourth port at the wrong address.
Make use of quirk to fix it.

Fixes: c8d192428f ("serial: 8250: added acces i/o products quad and octal serial cards")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-13 19:48:57 +01:00
Jay Dolan b896b03bc7 serial: 8250_pci: Fix number of ports for ACCES serial cards
Have the correct number of ports created for ACCES serial cards. Two port
cards show up as four ports, and four port cards show up as eight.

Fixes: c8d192428f ("serial: 8250: added acces i/o products quad and octal serial cards")
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-13 19:48:50 +01:00
Heikki Krogerus 54b2f300f3 serial: 8250_pci: Replace custom code with pci_match_id()
serial_pci_is_blacklisted() is very similar to pci_match_id() implementation.
Replace it with the latter.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-11 09:55:50 +01:00
Greg Kroah-Hartman c744ca39f2 Merge 5.0-rc6 into tty-next
We need the tty fixes in here for other patches to be based on.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-11 09:26:45 +01:00
Andy Shevchenko 824d17c57b serial: 8250_pci: Make PCI class test non fatal
As has been reported the National Instruments serial cards have broken
PCI class.

The commit 7d8905d064

  ("serial: 8250_pci: Enable device after we check black list")

made the PCI class check mandatory for the case when device is listed in
a quirk list.

Make PCI class test non fatal to allow broken card be enumerated.

Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Cc: stable <stable@vger.kernel.org>
Reported-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: KHUENY.Gerhard <Gerhard.KHUENY@bachmann.info>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30 09:35:46 +01:00
Gustavo A. R. Silva 1575c083a7 tty: serial: 8250_mtk: Fix potential NULL pointer dereference
There is a potential NULL pointer dereference in case devm_kzalloc()
fails and returns NULL.

Fix this by adding a NULL check on data->dma

This bug was detected with the help of Coccinelle.

Fixes: 85b5c1dd04 ("serial: 8250-mtk: add uart DMA support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30 09:35:46 +01:00
Zhou Yanjie 8a417cdeb0 Serial: Ingenic: Add support for the X1000.
Add support for probing the 8250_ingenic driver on the
X1000 Soc from Ingenic.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30 09:31:30 +01:00
Linus Walleij 3a50365d8c serial: 8250: Add OF support for Xscale variant
This adds support for device tree probing for the Intel
Xscale 8250 variant needed to support device tree on
the Intel IXP4xx platforms.

Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30 09:31:30 +01:00
Greg Kroah-Hartman 83b21ed0fc Merge 5.0-rc4 into tty-next
We need the tty and serial fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-28 08:22:00 +01:00
He Zhe 352c4cf40c serial: 8250: Fix serial8250 initialization crash
The initialization code of interrupt backoff work might reference NULL
pointer and cause the following crash, if no port was found.

[   10.017727] CPU 0 Unable to handle kernel paging request at virtual address 000001b0, epc == 807088e0, ra == 8070863c
---- snip ----
[   11.704470] [<807088e0>] serial8250_register_8250_port+0x318/0x4ac
[   11.747251] [<80708d74>] serial8250_probe+0x148/0x1c0
[   11.789301] [<80728450>] platform_drv_probe+0x40/0x94
[   11.830515] [<807264f8>] really_probe+0xf8/0x318
[   11.870876] [<80726b7c>] __driver_attach+0x110/0x12c
[   11.910960] [<80724374>] bus_for_each_dev+0x78/0xcc
[   11.951134] [<80725958>] bus_add_driver+0x200/0x234
[   11.989756] [<807273d8>] driver_register+0x84/0x148
[   12.029832] [<80d72f84>] serial8250_init+0x138/0x198
[   12.070447] [<80100e6c>] do_one_initcall+0x5c/0x2a0
[   12.110104] [<80d3a208>] kernel_init_freeable+0x370/0x484
[   12.150722] [<80a49420>] kernel_init+0x10/0xf8
[   12.191517] [<8010756c>] ret_from_kernel_thread+0x14/0x1c

This patch makes sure the initialization code can be reached only if a port
is found.

Fixes: 6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during input overruns")
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18 13:03:47 +01:00
Vignesh R 7d470ebf58 serial: 8250_omap: Use clk_get_rate() to obtain fclk frequency
8250_omap driver uses clock-frequency DT property to obtain functional
clk frequency. This is not ideal as users need to calculate functional
clk frequency offline and populate it in DT.
Therefore add support to obtain functional clock frequency using clk
APIs when clock-frequency DT property is not defined.

Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18 11:23:00 +01:00
Vignesh R d6ce4ec0b8 serial: 8250_omap: Drop check for of_node
8250_omap is DT only driver so dev->of_node always exists. Drop check
for existence of valid dev->of_node to simplify omap8250_probe().

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18 11:23:00 +01:00
Andy Shevchenko d7dba6be0f dmaengine: dw: Remove misleading is_private property
The commit a9ddb575d6

   ("dmaengine: dw_dmac: Enhance device tree support")

introduces is_private property in uncertain understanding what does it mean.

First of all, documentation defines DMA_PRIVATE capability as

Documentation/crypto/async-tx-api.txt:
  The DMA_PRIVATE capability flag is used to tag dma devices that should not be
  used by the general-purpose allocator. It can be set at initialization time
  if it is known that a channel will always be private. Alternatively,
  it is set when dma_request_channel() finds an unused "public" channel.

  A couple caveats to note when implementing a driver and consumer:
  1/ Once a channel has been privately allocated it will no longer be
     considered by the general-purpose allocator even after a call to
     dma_release_channel().
  2/ Since capabilities are specified at the device level a dma_device with
     multiple channels will either have all channels public, or all channels
     private.

Documentation/driver-api/dmaengine/provider.rst:
  - DMA_PRIVATE
    The devices only supports slave transfers, and as such isn't available
    for async transfers.

The capability had been introduced by the commit 59b5ec2144

  ("dmaengine: introduce dma_request_channel and private channels")

and some code didn't changed from that times ever.

Taking into consideration above and the fact that on all known platforms
Synopsys DesignWare DMA engine is attached to serve slave transfers,
the DMA_PRIVATE capability must be enabled for this device unconditionally.
Otherwise, as rightfully noticed in drivers/dma/at_xdmac.c:
  /*
   * Without DMA_PRIVATE the driver is not able to allocate more than
   * one channel, second allocation fails in private_candidate.
   */
because of of a caveats mentioned in above documentation excerpts.

So, remove conditional around DMA_PRIVATE followed by removal leftovers.

If someone wonders, DMA_PRIVATE can be not used if and only if the all channels
of the DMA controller are supposed to serve memory-to-memory like operations.
For example, EP93xx has two controllers, one of which can only perform
memory-to-memory transfers

Note, this change doesn't affect dmatest to be able to test such controllers.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (maintainer:SERIAL DRIVERS)
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2019-01-07 17:57:13 +05:30
Linus Torvalds 117eda8f71 TTY/Serial driver patches for 4.21-rc1
Here is the large TTY/Serial driver set of patches for 4.21-rc1.
 
 A number of small serial driver changes along with some good tty core
 fixes for long-reported issues with locking.  There is also a new
 console font added to the tree, for high-res screens, so that should be
 helpful for many.
 
 The last patch in the series is a revert of an older one in the tree, it
 came late but it resolves a reported issue that linux-next was having
 for some people.
 
 Full details are in the shortlog, and all of these, with the exception
 of the revert, have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCY+1w8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+yl9PgCXckFuSe66uNMzdq2jsVgLKtMR+ACbBzrLQeMZ
 LU8UpaVqDJrrPxVURGY=
 =a/Xk
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial driver updates from Greg KH:
 "Here is the large TTY/Serial driver set of patches for 4.21-rc1.

  A number of small serial driver changes along with some good tty core
  fixes for long-reported issues with locking. There is also a new
  console font added to the tree, for high-res screens, so that should
  be helpful for many.

  The last patch in the series is a revert of an older one in the tree,
  it came late but it resolves a reported issue that linux-next was
  having for some people.

  Full details are in the shortlog, and all of these, with the exception
  of the revert, have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (85 commits)
  Revert "serial: 8250: Default SERIAL_OF_PLATFORM to SERIAL_8250"
  serial: sccnxp: Allow to use non-standard baud rates
  serial: sccnxp: Adds a delay between sequential read/write cycles
  tty: serial: qcom_geni_serial: Fix UART hang
  tty: serial: qcom_geni_serial: Fix wrap around of TX buffer
  serial: max310x: Fix tx_empty() callback
  dt-bindings: serial: sh-sci: Document r8a774c0 bindings
  dt-bindings: serial: sh-sci: Document r8a774a1 bindings
  Fonts: New Terminus large console font
  dt-bindings: serial: lpuart: add imx8qxp compatible string
  serial: uartps: Fix interrupt mask issue to handle the RX interrupts properly
  serial: uartps: Fix error path when alloc failed
  serial: uartps: Check if the device is a console
  serial: uartps: Add the device_init_wakeup
  tty: serial: samsung: Increase maximum baudrate
  tty: serial: samsung: Properly set flags in autoCTS mode
  tty: Use of_node_name_{eq,prefix} for node name comparisons
  tty/serial: do not free trasnmit buffer page under port lock
  serial: 8250: Rate limit serial port rx interrupts during input overruns
  dt-bindings: serial: 8250: Add rate limit for serial port input overruns
  ...
2018-12-28 20:33:54 -08:00
Greg Kroah-Hartman 598134ffca Revert "serial: 8250: Default SERIAL_OF_PLATFORM to SERIAL_8250"
This reverts commit 6d11023c34.

It causes issues with Guenter's test systems and since there seems to
not be any agreement about _why_ this is a problem, but reverting it
fixes things, let's revert until the root cause is found.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-24 09:18:00 +01:00
Paul Burton 3c9dc275db Revert "serial: 8250: Fix clearing FIFOs in RS485 mode again"
Commit f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode
again") makes a change to FIFO clearing code which its commit message
suggests was intended to be specific to use with RS485 mode, however:

 1) The change made does not just affect __do_stop_tx_rs485(), it also
    affects other uses of serial8250_clear_fifos() including paths for
    starting up, shutting down or auto-configuring a port regardless of
    whether it's an RS485 port or not.

 2) It makes the assumption that resetting the FIFOs is a no-op when
    FIFOs are disabled, and as such it checks for this case & explicitly
    avoids setting the FIFO reset bits when the FIFO enable bit is
    clear. A reading of the PC16550D manual would suggest that this is
    OK since the FIFO should automatically be reset if it is later
    enabled, but we support many 16550-compatible devices and have never
    required this auto-reset behaviour for at least the whole git era.
    Starting to rely on it now seems risky, offers no benefit, and
    indeed breaks at least the Ingenic JZ4780's UARTs which reads
    garbage when the RX FIFO is enabled if we don't explicitly reset it.

 3) By only resetting the FIFOs if they're enabled, the behaviour of
    serial8250_do_startup() during boot now depends on what the value of
    FCR is before the 8250 driver is probed. This in itself seems
    questionable and leaves us with FCR=0 & no FIFO reset if the UART
    was used by 8250_early, otherwise it depends upon what the
    bootloader left behind.

 4) Although the naming of serial8250_clear_fifos() may be unclear, it
    is clear that callers of it expect that it will disable FIFOs. Both
    serial8250_do_startup() & serial8250_do_shutdown() contain comments
    to that effect, and other callers explicitly re-enable the FIFOs
    after calling serial8250_clear_fifos(). The premise of that patch
    that disabling the FIFOs is incorrect therefore seems wrong.

For these reasons, this reverts commit f6aa5beb45 ("serial: 8250: Fix
clearing FIFOs in RS485 mode again").

Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode again").
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-17 16:18:29 +01:00
Darwin Dingel 6d7f677a2a serial: 8250: Rate limit serial port rx interrupts during input overruns
When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the characters to the workqueue
for the tty layer to handle them. When this busy time on the serial/tty
subsystem happens during boot, where it is also busy on the userspace
trying to initialise, some processes can continuously get preempted
and will be on hold until the interrupts subside.

The fix is to backoff on processing received characters for a specified
amount of time when an input overrun is seen (received a new character
before the previous one is processed). This only stops receive and will
continue to transmit characters to serial port. After the backoff period
is done, it receive will be re-enabled. This is optional and will only
be enabled by setting 'overrun-throttle-ms' in the dts.

Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-17 16:02:57 +01:00
Greg Kroah-Hartman 9c96f401e9 Merge 4.20-rc6 into tty-next
We want the TTY changes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-10 10:17:45 +01:00
Peter Shih 100bc3e2be tty: serial: 8250_mtk: always resume the device in probe.
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.

This basically reverts the change in commit 68e5fc4a25 ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.

Fixes: 68e5fc4a25 ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05 11:31:21 +01:00
Long Cheng 85b5c1dd04 serial: 8250-mtk: add uart DMA support
Modify uart register to support DMA function.

Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05 11:02:39 +01:00
Douglas Anderson 596f63da42 serial: 8250: Process sysrq at port unlock time
Let's take advantage of the new ("serial: core: Allow processing sysrq
at port unlock time") to handle sysrqs more cleanly.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-09 09:07:18 -08:00
Florian Fainelli 6d11023c34 serial: 8250: Default SERIAL_OF_PLATFORM to SERIAL_8250
It is way too easy to miss enabling SERIAL_OF_PLATFORM which would
result in the inability for the kernel to have a valid console device,
which can be seen with:

Warning: unable to open an initial console.

and then:

Run /init as init process
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100

Since SERIAL_OF_PLATFORM already depends on SERIAL_8250 && OF there
really is no drawback to defaulting this config to the value of
SERIAL_8250.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-09 09:07:17 -08:00
Greg Kroah-Hartman 4e1a606d55 Merge 4.19-rc7 into tty-next
We want the fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-08 15:43:12 +02:00
Guenter Roeck beeeac43b6 Revert "serial: 8250_dw: Fix runtime PM handling"
This reverts commit d76c74387e.

While commit d76c74387e ("serial: 8250_dw: Fix runtime PM handling")
fixes runtime PM handling when using kgdb, it introduces a traceback for
everyone else.

BUG: sleeping function called from invalid context at
	/mnt/host/source/src/third_party/kernel/next/drivers/base/power/runtime.c:1034
in_atomic(): 1, irqs_disabled(): 1, pid: 1, name: swapper/0
7 locks held by swapper/0/1:
 #0: 000000005ec5bc72 (&dev->mutex){....}, at: __driver_attach+0xb5/0x12b
 #1: 000000005d5fa9e5 (&dev->mutex){....}, at: __device_attach+0x3e/0x15b
 #2: 0000000047e93286 (serial_mutex){+.+.}, at: serial8250_register_8250_port+0x51/0x8bb
 #3: 000000003b328f07 (port_mutex){+.+.}, at: uart_add_one_port+0xab/0x8b0
 #4: 00000000fa313d4d (&port->mutex){+.+.}, at: uart_add_one_port+0xcc/0x8b0
 #5: 00000000090983ca (console_lock){+.+.}, at: vprintk_emit+0xdb/0x217
 #6: 00000000c743e583 (console_owner){-...}, at: console_unlock+0x211/0x60f
irq event stamp: 735222
__down_trylock_console_sem+0x4a/0x84
console_unlock+0x338/0x60f
__do_softirq+0x4a4/0x50d
irq_exit+0x64/0xe2
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.19.0-rc5 #6
Hardware name: Google Caroline/Caroline, BIOS Google_Caroline.7820.286.0 03/15/2017
Call Trace:
 dump_stack+0x7d/0xbd
 ___might_sleep+0x238/0x259
 __pm_runtime_resume+0x4e/0xa4
 ? serial8250_rpm_get+0x2e/0x44
 serial8250_console_write+0x44/0x301
 ? lock_acquire+0x1b8/0x1fa
 console_unlock+0x577/0x60f
 vprintk_emit+0x1f0/0x217
 printk+0x52/0x6e
 register_console+0x43b/0x524
 uart_add_one_port+0x672/0x8b0
 ? set_io_from_upio+0x150/0x162
 serial8250_register_8250_port+0x825/0x8bb
 dw8250_probe+0x80c/0x8b0
 ? dw8250_serial_inq+0x8e/0x8e
 ? dw8250_check_lcr+0x108/0x108
 ? dw8250_runtime_resume+0x5b/0x5b
 ? dw8250_serial_outq+0xa1/0xa1
 ? dw8250_remove+0x115/0x115
 platform_drv_probe+0x76/0xc5
 really_probe+0x1f1/0x3ee
 ? driver_allows_async_probing+0x5d/0x5d
 driver_probe_device+0xd6/0x112
 ? driver_allows_async_probing+0x5d/0x5d
 bus_for_each_drv+0xbe/0xe5
 __device_attach+0xdd/0x15b
 bus_probe_device+0x5a/0x10b
 device_add+0x501/0x894
 ? _raw_write_unlock+0x27/0x3a
 platform_device_add+0x224/0x2b7
 mfd_add_device+0x718/0x75b
 ? __kmalloc+0x144/0x16a
 ? mfd_add_devices+0x38/0xdb
 mfd_add_devices+0x9b/0xdb
 intel_lpss_probe+0x7d4/0x8ee
 intel_lpss_pci_probe+0xac/0xd4
 pci_device_probe+0x101/0x18e
...

Revert the offending patch until a more comprehensive solution
is available.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: d76c74387e ("serial: 8250_dw: Fix runtime PM handling")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-02 14:35:10 -07:00
Dai Okamura aad2d4952d serial: 8250_uniphier: add auto-flow-control support
Add selective auto-flow-control support for UniPhier serial driver.

Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-02 13:38:58 -07:00
Masahiro Yamada aca70d19c8 serial: 8250_uniphier: flatten probe function
Currently, the DT-related settings are split out to
uniphier_of_serial_setup(), but it turned out to be not nice.
The next commit will add a DT property, but it will not fit in
the helper.  Merge the helper into the probe function.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-02 13:38:58 -07:00
Masahiro Yamada 2fd8e45418 serial: 8250_uniphier: remove unused "fifo-size" property
The FIFO size of the UART devices is 64 on almost all UniPhier SoCs
with the exception Pro4TV SoC (MN2WS0235), which used 128 FIFO size.
However, Pro4TV SoC was never upstreamed, and out of production.

So, this property has never been used in a useful way.
Let's remove old unused code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-02 13:38:58 -07:00
Marek Vasut f6aa5beb45 serial: 8250: Fix clearing FIFOs in RS485 mode again
The 8250 FIFOs indeed need to be cleared after stopping transmission in
RS485 mode without SER_RS485_RX_DURING_TX flag set. But there are two
problems with the approach taken by the previous patch from Fixes tag.

First, serial8250_clear_fifos() should clear fifos, but what it really
does is it enables the FIFOs unconditionally if present, clears them
and then sets the FCR register to zero, which effectively disables the
FIFOs. In case the FIFO is disabled, enabling it and clearing it makes
no sense and in fact can trigger misbehavior of the 8250 core. Moreover,
the FCR register may contain other FIFO configuration bits which may not
be writable unconditionally and writing them incorrectly can trigger
misbehavior of the 8250 core too. (ie. AM335x UART swallows the first
byte and retransmits the last byte twice because of this FCR write).

Second, serial8250_clear_and_reinit_fifos() completely reloads the FCR,
but what really has to happen at the end of the RS485 transmission is
clearing of the FIFOs and nothing else.

This patch repairs serial8250_clear_fifos() so that it really only
clears the FIFOs by operating on FCR[2:1] bits and leaves all the
other bits alone. It also undoes serial8250_clear_and_reinit_fifos()
from __do_stop_tx_rs485() as serial8250_clear_fifos() is sufficient.

Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 2bed8a8e70 ("Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break")
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # let it bake a bit before merging
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18 16:07:25 +02:00
John Garry a27d938251 serial: 8250_of: Fix for lack of interrupt support
In commit c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ"), a
check was added for the UART driver being probed prior to the parent IRQ
controller.

Unfortunately this breaks certain boards which have no interrupt support,
like Huawei D03.

Indeed, the 8250 DT bindings state that interrupts should be supported -
not must.

To fix, switch from irq_of_parse_and_map() to of_irq_get(), which
does relay whether the IRQ host controller domain is not ready, i.e.
defer probe, instead of assuming it.

Fixes: c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ")
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18 16:07:25 +02:00
Lokesh Vutla c886751465 serial: 8250_omap: Make 8250_omap driver driver depend on ARCH_K3
Allow 8250 omap serial driver to be used for K3 platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18 16:07:24 +02:00
Sebastian Andrzej Siewior 9d7c249a1e serial: 8250: drop the printk from serial8250_interrupt()
The printk() in serial8250_interrupt() was once hidden behind a debug
macro in commit f4f653e987 ("serial: 8250, disable "too much work"
messages") and reverted back in commit 12de375ec4 ("Revert "serial:
8250, disable "too much work" messages"").

This was introduced first in 0.99.13k with the "serial" driver itself
(and called pass_number with a limit of 64 and no print). In 1.1.13 it
was renamed to pass_counter and the printk was behind #if 0. In 1.1.94
the limit of 64 was increased to 256 and hidden behind
RS_ISR_PASS_LIMIT. With this change the #if 0 turned into #if 1. It
slowly become what we have today with a loop limit of 512.

Usually, that printk isn't hit. However on KVM with a busy UART and
overloaded host it might happen. It is also likely with threaded
interrupts and a task which preempts the interrupt handler.

If the UART has (legitimate) work to do and we break out of the loop,
nothing changes: the interrupt is most likely already pending in the
interrupt controller and we end up in the handler anyway. This printk is
hardly helping.

Older kernels also had a comment saying that a bad configuration might
lead to this but I don't see how that should happen because a wrongly
configured interrupt number would let the handler leave "early" with
IRQ_NONE and the spurious detected will handle that (weill since 2.6.11,
before that we had no spurious detector). In that case, we would never
loop that often here.

This loop looks like an optimisation in order to pull the bytes from the
FIFO which were received while we were already here instead of waiting
for the interrupt. This might have been a good idea while the CPUs were
slow and FIFOs small.
There are other serial driver in tree, like the amba-pl*, which also
have this kind of a loop but without the printk (and were based on this
driver).

Remove the printk which might trigger in otherwise valid situtations.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18 16:07:23 +02:00
Linus Torvalds d5acba26bf Char/Misc driver patches for 4.19-rc1
Here is the bit set of char/misc drivers for 4.19-rc1
 
 There is a lot here, much more than normal, seems like everyone is
 writing new driver subsystems these days...  Anyway, major things here
 are:
 	- new FSI driver subsystem, yet-another-powerpc low-level
 	  hardware bus
 	- gnss, finally an in-kernel GPS subsystem to try to tame all of
 	  the crazy out-of-tree drivers that have been floating around
 	  for years, combined with some really hacky userspace
 	  implementations.  This is only for GNSS receivers, but you
 	  have to start somewhere, and this is great to see.
 Other than that, there are new slimbus drivers, new coresight drivers,
 new fpga drivers, and loads of DT bindings for all of these and existing
 drivers.
 
 Full details of everything is in the shortlog.
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
 cvW7a+McOoKz/MGmEKsi
 =TNfn
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver updates from Greg KH:
 "Here is the bit set of char/misc drivers for 4.19-rc1

  There is a lot here, much more than normal, seems like everyone is
  writing new driver subsystems these days... Anyway, major things here
  are:

   - new FSI driver subsystem, yet-another-powerpc low-level hardware
     bus

   - gnss, finally an in-kernel GPS subsystem to try to tame all of the
     crazy out-of-tree drivers that have been floating around for years,
     combined with some really hacky userspace implementations. This is
     only for GNSS receivers, but you have to start somewhere, and this
     is great to see.

  Other than that, there are new slimbus drivers, new coresight drivers,
  new fpga drivers, and loads of DT bindings for all of these and
  existing drivers.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
  android: binder: Rate-limit debug and userspace triggered err msgs
  fsi: sbefifo: Bump max command length
  fsi: scom: Fix NULL dereference
  misc: mic: SCIF Fix scif_get_new_port() error handling
  misc: cxl: changed asterisk position
  genwqe: card_base: Use true and false for boolean values
  misc: eeprom: assignment outside the if statement
  uio: potential double frees if __uio_register_device() fails
  eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
  misc: ti-st: Fix memory leak in the error path of probe()
  android: binder: Show extra_buffers_size in trace
  firmware: vpd: Fix section enabled flag on vpd_section_destroy
  platform: goldfish: Retire pdev_bus
  goldfish: Use dedicated macros instead of manual bit shifting
  goldfish: Add missing includes to goldfish.h
  mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
  dt-bindings: mux: add adi,adgs1408
  Drivers: hv: vmbus: Cleanup synic memory free path
  Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
  Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
  ...
2018-08-18 11:04:51 -07:00
Mark 47ac76662c tty: serial: 8250: Revert NXP SC16C2552 workaround
Revert commit ecb988a3b7985913d1f0112f66667cdd15e40711: tty: serial:
8250: 8250_core: NXP SC16C2552 workaround

The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:

PSW 80000000 INST 00000000                           HALT
//

What is displayed is some variation of:

T 00000000           HAL//

Reverting this commit via this patch fixes my problem.

Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Fixes: ecb988a3b7 ("tty: serial: 8250: 8250_core: NXP SC16C2552 workaround")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-12 18:53:30 +02:00
Aaron Sierra 60ab0fafc4 serial: 8250_exar: Read INT0 from slave device, too
The sleep wake-up refactoring that I introduced in

  commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")

did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:

  commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs")

This also converts an ioread8() to readb() in order to provide visual
consistency with the MMIO-only accessors used elsewhere in the driver.

Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Fixes: c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-02 10:11:35 +02:00
Srinath Mannam 784c29eda5 serial: 8250_dw: Add ACPI support for uart on Broadcom SoC
Add ACPI identifier HID for UART DW 8250 on Broadcom SoCs
to match the HID passed through ACPI tables to enable
UART controller.

Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Tested-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-02 10:11:32 +02:00
Chen Hu dfcab6ba57 serial: 8250_dw: always set baud rate in dw8250_set_termios
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[   54.928108] dw8250_set_termios+0x162/0x170
[   54.928114] serial8250_set_termios+0x17/0x20
[   54.928117] uart_change_speed+0x64/0x160
[   54.928119] uart_resume_port
...

So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.

We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.

Signed-off-by: Chen Hu <hu1.chen@intel.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-02 10:11:32 +02:00
Andy Shevchenko 286d9b8c7d serial: 8250: Use cached port name directly in messages
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.

This will make it one place source for easier maintenance or
modifications.

While here, replace printk_ratelimited(KERN_INFO ) by pr_info_ratelimited().
It seems last printk() call in 8250_port.c.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-25 12:51:23 +02:00
Andy Shevchenko b340cbbea5 serial: 8250_exar: Drop unused variable in pci_xr17v35x_setup()
After removal has_slave use the variable board becomes unused.
Remove it to avoid a warning:

drivers/tty/serial/8250/8250_exar.c: In function 'pci_xr17v35x_setup':
drivers/tty/serial/8250/8250_exar.c:380:31: warning: unused variable 'board' [-Wunused-variable]
  const struct exar8250_board *board = priv->board;
                               ^~~~~

Fixes: 328c11f24b ("serial: 8250_exar: Remove useless has_slave member")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-23 14:15:49 +02:00
Andy Shevchenko 26f22d5748 serial: 8250_exar: Describe all members in struct exar8250_board
Describe all memebers in struct exar8250_board, otherwise we get a warning:

drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'has_slave' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'setup' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'exit' not described in 'exar8250_board'

No functional change intended.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-21 08:40:45 +02:00
Andy Shevchenko 328c11f24b serial: 8250_exar: Remove useless has_slave member
Exar UARTs by default supports only up to 8 channels,
all above go as extension. Thus, there is no need to have
an additional property to distinguish them from first ones.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-21 08:40:45 +02:00
Phil Edworthy 2ff5fa7f74 serial: 8250_dw: Add compatible string for Renesas RZ/N1 UART
The Renesas RZ/N1 UART is based on the Synopsys DW UART, but has additional
registers for DMA. This patch does not address the changes required for DMA
support, it simply adds the compatible string.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-21 08:39:25 +02:00
Alexander Sverdlin c58caaab3b serial: 8250: of: Defer probe on missing IRQ
If the IRQ controller is not yet probed do not proceed with irq=0,
try to defer the probe.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-16 11:56:22 +02:00
Alexander Sverdlin b29330d829 serial: 8250: of: Correct of_platform_serial_setup() error handling
Don't dispose IRQ mapping before it has been created.

Fixes: aa9594740 ("serial: 8250_of: Add IO space support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-16 11:56:22 +02:00
Greg Kroah-Hartman 83cf9cd6d5 Merge 4.18-rc5 into char-misc-next
We want the char-misc fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-16 09:04:54 +02:00
Jisheng Zhang 701c5e73b2 serial: 8250_dw: add fractional divisor support
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register. The fractional divisor width is
4bits ~ 6bits.

Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups dw specific get_divisor() and set_divisor() hook.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-12 17:07:26 +02:00
Jisheng Zhang 6226e5f31a serial: 8250: export serial8250_do_set_divisor()
Some drivers could call serial8250_do_set_divisor() to complete its
own set_divisor routine. Export this symbol for code reusing.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-12 17:07:26 +02:00
Jisheng Zhang 0238d2b4a4 serial: 8250: introduce get_divisor() and set_divisor() hook
Add these two hooks so that they can be overridden with driver specific
implementations.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-12 17:07:26 +02:00
Randy Dunlap ac3167257b headers: separate linux/mod_devicetable.h from linux/platform_device.h
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel.  It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.

   4146 #include <linux/platform_device.h>

After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.

    225 #include <linux/mod_devicetable.h>

This patch was build-tested on 20 different arch-es.

It also makes these drivers SubmitChecklist#1 compliant.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-07 17:52:26 +02:00
Andy Shevchenko 3ff10703c7 serial: 8250_dw: Introduce IO accessors to extended registers
There are several extended (in comparison to the traditional 16550)
registers are present in Synopsys DesignWare UART. All of them
are 32-bit ones.

Introduce helpers to simplify access to them and convert existing users.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-07 17:00:51 +02:00
Jisheng Zhang 6101be86cb serial: 8250: let serial8250_get_divisor() get uart_port * as param
Align serial8250_get_divisor() with serial8250_set_divisor() to accept
uart_port pointer as the first parameter. No functionality changes.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-06 16:45:38 +02:00
Greg Kroah-Hartman 16ecf49c10 Merge 4.18-rc3 into tty-next
We want ths tty core changes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-02 08:23:43 +02:00
Andy Shevchenko 20dcff436e serial: 8250_pci: Remove stalled entries in blacklist
After the commit

  7d8905d064 ("serial: 8250_pci: Enable device after we check black list")

pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.

So, remove the entries from blacklist in order to get cards enumerated.

Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Matt Turner <mattst88@gmail.com>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28 21:34:39 +09:00
Zhouyang Jia 85c634e919 drivers/tty: add error handling for pcmcia_loop_config
When pcmcia_loop_config fails, the lack of error-handling code may
cause unexpected results.

This patch adds error-handling code after calling pcmcia_loop_config.

Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28 21:23:44 +09:00
Nishanth Menon be70874498 serial: 8250_omap: Add support for AM654 UART controller
AM654 uses a UART controller that is compatible (partially) with
existing 8250 UART, however, has a few differences with respect to DMA
support and control paths. Introduce a base definition that allows us
to build up the differences in follow on patches.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28 21:23:44 +09:00
Daniel Golle 9d93989444 tty: serial: exar: generalize RS485 setup
Move the non-board-specific part of the RS485 initialization from
iot2040_rs485_config function to a new generic function used also for
other boards.
This allows using TIOCGRS485 and TIOCSRS485 on boards (such as mPCIe
serial IO modules) which are hard-wired to RS485 or have jumpers for
their configurations.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28 21:07:55 +09:00
Phil Edworthy d76c74387e serial: 8250_dw: Fix runtime PM handling
When using kgdb, you get an abort when accessing the UART registers.
This is because the driver has already entered runtime PM and so turned
off the bus clock needed to access the registers.

To fix this, set the capability indicating Runtime PM is active while idle.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 13:51:12 +02:00
Tony Lindgren 13dc04d0e5 serial: 8250: omap: Fix idling of clocks for unused uarts
I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.

After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.

This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.

Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.

Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.

And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.

Fixes: cdb929e445 ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 13:51:12 +02:00
Marek Vasut 3ace822ad4 serial: 8250: Add missing rxtrig_bytes on Altera 16550 UART
The Altera 16550 UART core supports FCR Rx Trigger Level setting,
but the port definition in the driver is missing the rxtrig_bytes
array specifying the trigger levels. Add the array to make the Rx
Trigger Level setting available on this type of 16550 UART.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 13:51:11 +02:00
Dan Carpenter a451debb41 serial/aspeed-vuart: fix a couple mod_timer() calls
The "unthrottle_timeout" is HZ/10 but mod_timer() takes a the actual
jiffie where you want it to timeout, not an offset.

Fixes: 5909c0bf9c ("serial/aspeed-vuart: Implement quick throttle mechanism")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 13:51:11 +02:00
John Garry aa95947400 serial: 8250_of: Add IO space support
Currently the 8250_of driver only supports MEM IO type
accesses.

Some development boards (Huawei D03, specifically) require
IO space access for 8250-compatible OF driver support, so
add it.

The modification is quite simple: just set the port iotype
and associated flags depending on the device address
resource type.

Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 13:48:29 +02:00
Michal Simek 700ad5531b serial: 8250_early: Setup divider when uartclk is passed
device->baud is always non zero value because it is checked already in
early_serial8250_setup() before init_port is called.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-25 14:56:12 +02:00
Jeremy Kerr 5909c0bf9c serial/aspeed-vuart: Implement quick throttle mechanism
Although we populate the ->throttle and ->unthrottle UART operations,
these may not be called until the ldisc has had a chance to schedule and
check buffer space. This means that we may overflow the flip buffers
without ever hitting the ldisc's throttle threshold.

This change implements an interrupt-based throttle, where we check for
space in the flip buffers before reading characters from the UART's
FIFO. If there's no space available, we disable the RX interrupt and
schedule a timer to check for space later.

For this, we need an unlocked version of the set_throttle function to be
able to change throttle state from the irq_handler, which already holds
port->lock.

This prevents a case where we drop characters under heavy RX load.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-23 10:16:50 +02:00
Jeremy Kerr 989983ea84 serial/aspeed-vuart: Implement rx throttling
The aspeed VUART runs at LPC bus frequency, rather than being restricted
to a typical UART baud rate. This means that the VUART can receive a lot
of data, which can overrun tty flip buffers, and/or cause a large amount
of interrupt traffic.

This change implements the uart_port->throttle & unthrottle callbacks,
implemented by disabling the receiver line status & received data
available IRQs.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-23 10:16:50 +02:00
Jeremy Kerr ebbaf9ab9e serial/8250: export serial8250_read_char
Currently, we export serial8250_rx_chars, which does a whole bunch of
reads from the 8250 data register, without any form of flow control
between reads.

An upcoming change to the aspeed vuart driver implements more
fine-grained flow control in the interrupt handler, requiring
character-at-a-time control over the rx path.

This change exports serial8250_read_char to allow this.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-23 10:16:50 +02:00
Kurt Kanzenbach 54e53b2e80 tty: serial: 8250: pass IRQ shared flag to UART ports
On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.

This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling rountines himself.

Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.

Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.

Example stacktrace by performing echo 1 > /dev/ttyS2 on a non-patched system:

|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85

Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-23 10:13:16 +02:00
Vignesh R 09d8b2bdbc serial: 8250: omap: Provide ability to enable/disable UART as wakeup source
Enable/Clear module level UART wakeup in UART_OMAP_WER register based on
return value of device_may_wakeup() in .suspend(). This allows
userspace to use sysfs to control the ability of UART to wakeup the
system from deep sleep state. Register is restored back in .startup()
call that happens as part of resume sequence.

With this patch, userspace can control UART wakeup capability via sysfs:
To enable wakeup capability:
echo enabled >  /sys/class/tty/ttyXX/device/power/wakeup
For disabling wakeup capability:
echo disabled > /sys/class/tty/ttyXX/device/power/wakeup

Note that the UART wakeup events configured in the 8250 hardware only
work for idle modes that do not cut off power for the UART. For deeper
idle states, dedicated padconf wakeirqs must be used. Or in some cases
the UART RX pin can be remuxed to GPIO input if the GPIO block stays
powered.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-23 10:12:14 +02:00
Joshua Scott b7639b0b15 serial: 8250_dw: Limit dw8250_tx_wait_empty quirk to armada-38x devices
The previous implementation has had a detrimental effect on devices using
high bitrates (bluetooth), as the fifo being non-empty for a single check
would result in a 10 µs delay.

Limit the change to devices with the new "marvell,armada-38x-uart"
compatible string. Also update the code to allow the first 1000 retries
to not perform a delay.

The maximum duration of retries has been increased to cover a worst-case
seen on the Armada 385 SoC. "dmesg ; resize", will fill the buffer with
text to output before doing a resize. At 9600 baud this took up to 13 ms
to flush all characters and avoid some getting lost.

Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-23 10:11:13 +02:00
Greg Kroah-Hartman 4958134df5 Merge 4.16-rc6 into tty-next
We want the serial/tty fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-20 11:27:18 +01:00
Michael Moese e2fea54e45 8250-men-mcb: add support for 16z025 and 16z057
Add support for two MEN UARTs (16z025 and 16z057) to the
8250_men_mcb driver.
The 16z025 consists of up to four ports, the 16z057 has
exactly four ports. Apart from that, all of them share the
Port settings.

Signed-off-by: Michael Moese <mmoese@suse.de>
Reported-by: Ben Turner <ben.turner@21net.com>
Tested-by: Ben Turner <ben.turner@21net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-15 18:12:55 +01:00
Joel Stanley f597fbce38 serial: 8250: Add Nuvoton NPCM UART
The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-09 11:01:19 -08:00
Andy Shevchenko 7d6e2143be serial: 8250_dw: Switch to use acpi_dev_present()
Special settings for APMC0D08 are applied when device is present
in the system. To check its presence we may use acpi_dev_present()
instead of current open coded variant.

Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-09 10:24:38 -08:00
Andy Shevchenko aad76f2c48 serial, pci_ids: Move duplicate IDs to PCI IDs database
PCI ID database is for IDs used across several drivers.
Here is the case for SUNIX combo cards.

No functional change intended.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28 15:33:04 +01:00
Nikola Ciprich 9f2068f357 serial: 8250_pci: Add Brainboxes UC-260 4 port serial device
Add PCI ids for two variants of Brainboxes UC-260 quad port
PCI serial cards.

Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28 13:48:21 +01:00
Andy Shevchenko e7f3e99cb1 serial: 8250_pci: Don't fail on multiport card class
Do not fail on multiport cards in serial_pci_is_class_communication().

It restores behaviour for SUNIX multiport cards, that enumerated by
class and have a custom board data.

Moreover it allows users to reenumerate port-by-port from user space.

Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28 13:48:21 +01:00
Joshua Scott 914eaf935e serial: 8250_dw: Allow TX FIFO to drain before writing to UART_LCR
An issue has been observed on the Marvell Armada 38x serial port.

Writes to UART_LCR can result in characters that are currently held in the
TX FIFO being lost rather than sent, even if the userspace process has
attempted to flush them.

This is most visible when using the "resize" command (tested on Busybox),
where we have observed the escape code for restoring cursor position
becoming mangled.

Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28 13:40:22 +01:00
Vignesh R 08fb00c64f serial: 8250: 8250_omap: Fix throttling when DMA is enabled
omap_8250_throttle() is called when tty RX buffer is about to overflow
and can no longer keep up with the rate at which UART is receiving data.
So, the expectation of this callback, is that UART stops RX and asserts
HW flow control to signal the sender to stop sending more data.
omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer
serviced, leading to assertion of flow control once RX FIFO is full.
But, this does not work when DMA is enabled as driver keeps queuing new
RX DMA request in completion handler without brothering about throttling
request made by the higher layer.
This patch introduces a flag that can be used to determine whether or
not to queue next RX DMA request based on throttling request.

Without this patch, tty buffer overflows are reported at higher
baudrates.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28 13:40:22 +01:00
Vignesh R 2e9fe53910 serial: 8250: Don't service RX FIFO if interrupts are disabled
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28 13:40:22 +01:00
Aaron Sierra c7e1b40590 tty: serial: exar: Relocate sleep wake-up handling
Exar sleep wake-up handling has been done on a per-channel basis by
virtue of INT0 being accessible from each channel's address space. I
believe this was initially done out of necessity, but now that Exar
devices have their own driver, we can do things more efficiently by
registering a dedicated INT0 handler at the PCI device level.

I see this change providing the following benefits:

    1. If more than one port is active, eliminates the redundant bus
       cycles for reading INT0 on every interrupt.
    2. This note associated with hooking in the per-channel handler in
       8250_port.c is resolved:
        /* Fixme: probably not the best place for this */

Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-25 12:44:50 +01:00
Andy Shevchenko c14b65feac serial: 8250_dw: Revert "Improve clock rate setting"
The commit

  de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")

obviously tries to cure symptoms, and not a root cause.

The root cause is the non-flexible rate calculation inside the
corresponding clock driver. What we need is to provide maximum UART
divisor value to the clock driver to allow it do the job transparently
to the caller.

Since from the initial commit message I have got no clue which clock
driver actually needs to be amended, I leave this exercise to the people
who know better the case.

Moreover, it seems [1] the fix introduced a regression. And possible
even one more [2].

Taking above, revert the commit de9e33bdfa for now.

[1]: https://www.spinics.net/lists/linux-serial/msg28872.html
[2]: https://github.com/Dunedan/mbp-2016-linux/issues/29#issuecomment-357583782

Fixes: de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Ed Blake <ed.blake@sondrel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-22 14:13:40 +01:00
Paul Cercueil ea507ce3e0 serial: 8250_ingenic: Parse earlycon options
In the devicetree, it is possible to specify the baudrate, parity,
bits, flow of the early console, by passing a configuration string like
this:

aliases {
	serial0 = &uart0;
};

chosen {
	stdout-path = "serial0:57600n8";
};

This, for instance, will configure the early console for a baudrate of
57600 bps, no parity, and 8 bits per baud.

This patches implements parsing of this configuration string in the
8250_ingenic driver, which previously just ignored it.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-09 16:49:14 +01:00
Paul Cercueil aed3d7012c serial: 8250_ingenic: Add support for the JZ4770 SoC
The JZ4770 SoC's UART is no different from the other JZ SoCs, so this
commit simply adds the ingenic,jz4770-uart compatible string.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-09 16:49:14 +01:00
Masahiro Yamada b9820a3169 serial: 8250_of: fix return code when probe function fails to get reset
The error pointer from devm_reset_control_get_optional_shared() is
not propagated.

One of the most common problem scenarios is it returns -EPROBE_DEFER
when the reset controller has not probed yet.  In this case, the
probe of the reset consumer should be deferred.

Fixes: e2860e1f62 ("serial: 8250_of: Add reset support")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-09 16:46:26 +01:00
Wei Yongjun 7defa77d2b serial: 8250_uniphier: fix error return code in uniphier_uart_probe()
Fix to return a negative error code from the port register error
handling case instead of 0, as done elsewhere in this function.

Fixes: 39be40ce06 ("serial: 8250_uniphier: fix serial port index in private data")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-09 16:45:17 +01:00
Rolf Evers-Fischer 93ad86735d serial: 8250: 8250_omap: Fix spelling error.
Fixed a spelling error in a comment.

Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-15 20:27:44 +01:00
Stefan Potyra 8af016aa5a serial: 8250_dw: Disable clock on error
If there is no clock rate for uartclk defined, disable the previously
enabled clock again.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 23f5b3fdd0 serial: 8250_dw: only get the clock rate in one place
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-15 20:27:43 +01:00
Christian Borntraeger 1598e38c07 serial: forbid 8250 on s390
Using "make kvmconfig" results in a potentially unusable linux image
on s390.  The reason is that both the (default on s390) sclp consoles
as well as the 8250 console register a ttyS<x> as console. Since there
will be no 8250 on s390 let's fence 8250. This will ensure that there
is always a working sclp console.

Reported-by: Alice Frosi <alice@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-15 20:21:28 +01:00
Matt Redfearn 0ff3ab7019 serial: 8250_early: Only set divisor if valid clk & baud
If either uartclk or baud are 0, avoid calculating and setting a divisor
based on them since the output will almost certainly be garbage.

This also allows platforms such as the MIPS generic kernel, which has no
way to know a valid BASE_BASE for the board it is actually booted on at
compile time, to set BASE_BAUD to 0 and avoid early_8250 setting a bad
divisor.

This fixes a regression caused by commit 31cb9a8575 ("earlycon:
initialise baud field of earlycon device structure"), which changed the
behavior of of_setup_earlycon such that it sets a baud rate in the
earlycon structure where previously it was left as 0. All boards
supported by the MIPS generic kernel started outputting garbage from the
boot console due to an incorrect divisor being set.

Fixes: 31cb9a8575 ("earlycon: initialise baud field of earlycon device structure")
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28 15:55:15 +01:00
Matt Wilson 3bfd1300ab serial: 8250_pci: Add Amazon PCI serial device ID
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).

[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28 15:55:15 +01:00
Kees Cook 841b86f328 treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:

    perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
        $(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)

    perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
        $(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)

The now unused macros are also dropped from include/linux/timer.h.

Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 16:35:54 -08:00
Linus Torvalds fb0255fb29 TTY/Serial patches for 4.15-rc1
Here is the big tty/serial driver pull request for 4.15-rc1.
 
 Lots of serial driver updates in here, some small vt cleanups, and a
 raft of SPDX and license boilerplate cleanups, messing up the diffstat a
 bit.
 
 Nothing major, with no realy functional changes except better hardware
 support for some platforms.
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnD+w8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ynAmgCfSSr/9qiCE0vfP5eVYjddzxfWyZ4AoMbKORZC
 5x2KVW0Btrbs3WmnD7ZU
 =PSea
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial updates from Greg KH:
 "Here is the big tty/serial driver pull request for 4.15-rc1.

  Lots of serial driver updates in here, some small vt cleanups, and a
  raft of SPDX and license boilerplate cleanups, messing up the diffstat
  a bit.

  Nothing major, with no realy functional changes except better hardware
  support for some platforms.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
  tty: ehv_bytechan: fix spelling mistake
  tty: serial: meson: allow baud-rates lower than 9600
  serial: 8250_fintek: Fix crash with baud rate B0
  serial: 8250_fintek: Disable delays for ports != 0
  serial: 8250_fintek: Return -EINVAL on invalid configuration
  tty: Remove redundant license text
  tty: serdev: Remove redundant license text
  tty: hvc: Remove redundant license text
  tty: serial: Remove redundant license text
  tty: add SPDX identifiers to all remaining files in drivers/tty/
  tty: serial: jsm: remove redundant pointer ts
  tty: serial: jsm: add space before the open parenthesis '('
  tty: serial: jsm: fix coding style
  tty: serial: jsm: delete space between function name and '('
  tty: serial: jsm: add blank line after declarations
  tty: serial: jsm: change the type of local variable
  tty: serial: imx: remove dead code imx_dma_rxint
  tty: serial: imx: disable ageing timer interrupt if dma in use
  serial: 8250: fix potential deadlock in rs485-mode
  serial: m32r_sio: Drop redundant .data assignment
  ...
2017-11-13 21:05:31 -08:00
Ji-Ze Hong (Peter Hong) 07a708f0a1 serial: 8250_fintek: Fix crash with baud rate B0
The 8250_fintek.c is support the Fintek F81866/F81216 with dynamic clock.
But It'll generate "division by zero" exception and crash in
fintek_8250_set_termios() with baud rate 0 on baudrate_table[i] % baud.

It can be tested with following C code:

	...
	struct termios options;

	tcgetattr(fd, &options);
	...
	options.c_cflag = CS8 | CREAD; /* baud rate 0 */
	tcsetattr(fd, TCSANOW, &options);
	tcflush(fd, TCIOFLUSH);

Fixes: 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Reported-by: Lukas Redlinger <rel+kernel@agilox.net>
Cc: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08 13:09:35 +01:00
Ricardo Ribalda Delgado 21c4e7f255 serial: 8250_fintek: Disable delays for ports != 0
According to the datasheet, only the first port supports delay before
send and delay after send.

Reported-by: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08 13:09:35 +01:00
Ricardo Ribalda Delgado 7ecc77011c serial: 8250_fintek: Return -EINVAL on invalid configuration
Hardware does not support having the same RTS level during RX and TX
when RS485 mode is on (URA in Fintek terminology).

The manufacturer has also confirmed that the delays are not enabled if
the RS485 mode is not enabled.

Therefore we should return -EINVAL if the user wants to have the same
value for RTS_ON_SEND and RTS_AFTER_SEND.

Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08 13:09:35 +01:00
Greg Kroah-Hartman 4793f2ebff tty: serial: Remove redundant license text
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08 13:08:12 +01:00
Greg Kroah-Hartman e3b3d0f549 tty: add SPDX identifiers to all remaining files in drivers/tty/
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself.  The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08 13:08:12 +01:00
Tomas Melin b86f86e8e7 serial: 8250: fix potential deadlock in rs485-mode
Canceling hrtimer when holding uart spinlock can deadlock.

CPU0: syscall write
          -> get uart port spinlock
              -> write uart
                  -> start_tx_rs485
                      -> hrtimer_cancel
                          -> wait for hrtimer callback to finish

CPU1: hrtimer IRQ
          -> run hrtimer
              -> em485_handle_stop_tx
                  -> get uart port spinlock

CPU0 is waiting for the hrtimer callback to finish, but the hrtimer
callback running on CPU1 is waiting to get the uart port spinlock.

This deadlock can be avoided by not canceling the hrtimers in these paths.
Setting active_timer=NULL can be done without accessing hrtimer,
and that will effectively cancel operations that would otherwise have been
performed by the hrtimer callback.

Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04 12:38:04 +01:00
Lukas Wunner 3236a96548 serial: 8250_fintek: Fix rs485 disablement on invalid ioctl()
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value.  If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending.  In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.

Fixes: 28e3fb6c4d ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04 12:08:53 +01:00
Kees Cook 7c3356457a serial: 8250: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Sean Young <sean@mess.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04 12:01:53 +01:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Ji-Ze Hong (Peter Hong) fd97e66c55 serial: 8250_fintek: Fix finding base_port with activated SuperIO
The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().

Tested on iBASE MI802.

Cc: stable@vger.kernel.org
Tested-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Reviewd-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-20 14:06:46 +02:00
Aaron Sierra 0ab84da2e0 serial: 8250: Preserve DLD[7:4] for PORT_XR17V35X
The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.

Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-20 14:06:45 +02:00
Ed Blake de9e33bdfa serial: 8250_dw: Improve clock rate setting
Currently dw8250_set_termios sets the input clock to the nearest
achievable rate to baudx16.  If necessary, the input clock is then
divided down to baudx16 using an integer divider within the UART
device, with the divisor calculated in the 8250 core driver.

However, the clock rate set by dw8250_set_termios and subsequently
divided down could be considerably different to the target baudx16
rate, resulting in incorrect operation.  This patch fixes this by
iteratively searching for an input clock rate that is within +/-1.6%
of an integer multiple of the target baudx16 rate.

Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-04 10:17:27 +02:00
Ed Blake 6263368c5b serial: Add define for max baud rate divisor
Add a define for the maximum baud rate divisor, to improve code
readability.

Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-04 10:17:27 +02:00
Andy Shevchenko daf3930cf6 serial: 8250_mid: Enable HSU on Intel Cedar Fork PCH
Intel Cedar Fork PCH has similar HSU as has been used on Intel Denverton.
Add PCI ID to get it enumerated.

While here, remove DNV part form INTEL_MID_UART_DNV_FISR to show that is
used not only on Intel Denverton from now on.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-04 10:17:27 +02:00
Ji-Ze Hong (Peter Hong) 4c3897b1b0 serial: 8250_fintek: fix warning reported from smatch
This patch is fix the warning reported by smatch as following:

drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03 20:31:17 +02:00
Ji-Ze Hong (Peter Hong) 58178914ae serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H
The F81216H had 4 clocksource 1.8432/18.432/14.769/24MHzand  baud rates can
be up to 1.5Mbits with 24MHz. The register value and mask is the same with
F81866. But F81866 register address is F2h, F81216H is F0h.

We'll implements the dynamic clocksource in fintek_8250_set_termios().

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03 20:31:17 +02:00
Ji-Ze Hong (Peter Hong) 195638b6d4 serial: 8250_fintek: UART dynamic clocksource on Fintek F81866
The F81866 had 4 clocksource 1.8432/18.432/14.769/24MHz and baud rates can
be up to 1.5Mbits with 24MHz. We'll implements the dynamic clocksource in
fintek_8250_set_termios().

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03 20:31:17 +02:00
Allen Pais 305615127a drivers: tty: 8250: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03 20:28:36 +02:00
Linus Torvalds e63a94f12b TTY/Serial updates for 4.14-rc1
Here is the big tty/serial driver update for 4.14-rc1.
 
 Well, not all that big, just a number of small serial driver fixes, and
 a new serial driver.  Also in here are some much needed goldfish tty
 driver (emulator) fixes to try to get that codebase under control.
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa2A+A8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ylNKACfWOuWb4PEGzPg2hF57V1g0cq8VXEAn0BtZT+n
 uuCBV53ylesoHhEhKf/D
 =g+za
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial updates from Greg KH:
 "Here is the big tty/serial driver update for 4.14-rc1.

  Well, not all that big, just a number of small serial driver fixes,
  and a new serial driver. Also in here are some much needed goldfish
  tty driver (emulator) fixes to try to get that codebase under control.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (94 commits)
  tty: goldfish: Implement support for kernel 'earlycon' parameter
  tty: goldfish: Use streaming DMA for r/w operations on Ranchu platforms
  tty: goldfish: Refactor constants to better reflect their nature
  serial: 8250_port: Remove useless NULL checks
  earlycon: initialise baud field of earlycon device structure
  tty: hvcs: make ktermios const
  pty: show associative slave of ptmx in fdinfo
  tty: n_gsm: Add compat_ioctl
  tty: hvcs: constify vio_device_id
  tty: hvc_vio: constify vio_device_id
  tty: mips_ejtag_fdc: constify mips_cdmm_device_id
  Introduce 8250_men_mcb
  mcb: introduce mcb_get_resource()
  serial: imx: Avoid post-PIO cleanup if TX DMA is started
  tty: serial: imx: disable irq after suspend
  serial: 8250_uniphier: add suspend/resume support
  serial: 8250_uniphier: use CHAR register for canary to detect power-off
  serial: 8250_uniphier: fix serial port index in private data
  serial: 8250: of: Add new port type for MediaTek BTIF controller on MT7622/23 SoC
  dt-bindings: serial: 8250: Add MediaTek BTIF controller bindings
  ...
2017-09-05 10:30:48 -07:00
Andy Shevchenko ae28d7402a serial: 8250_port: Remove useless NULL checks
After switching to HR timers for RS485 the NULL checks for the object
inside timer functions become useless.

Remove them to avoid confusion to static analyzers.

Fixes 6e0a5de213 ("serial: 8250: Use hrtimers for rs485 delays")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-31 18:47:31 +02:00
Michael Moese 562e6ef81f Introduce 8250_men_mcb
This patch introduces the 8250_men_mcb driver for the MEN 16Z125
IP-Core. This is a 16550-type UART with a 60 byte FIFO.
Due to strange old hardware, every board using this IP core requires
different values for uartclk. A reasonable default is included in
addition to the support of three boards. Additional values for other
boards will be added later.

This v2 has some whitespace fixes, I screwed this up yesterday.

Signed-off-by: Michael Moese <michael.moese@men.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:22 +02:00
Masahiro Yamada 3d16ddc13c serial: 8250_uniphier: add suspend/resume support
Add suspend/resume support for UniPhier serial driver.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:22 +02:00
Masahiro Yamada d3a9184773 serial: 8250_uniphier: use CHAR register for canary to detect power-off
The 8250 core uses the SCR as a canary to discover if the console has
been powered-off.

This hardware does not have SCR at offset 7, but an unused register
CHAR at a different offset.  As long as the character interrupt is
disabled, the register access has no impact, so it is useful as an
alternative scratch register.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:22 +02:00
Masahiro Yamada 39be40ce06 serial: 8250_uniphier: fix serial port index in private data
serial8250_register_8250_port() may allocate a different port index
than requested.  The driver needs to remember the returned value of
serial8250_register_8250_port() for later use.  Otherwise, the .remove
hook may unregister a different port.

Fixes: 1a8d2903cb ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:22 +02:00
Sean Wang 1c16ae65e2 serial: 8250: of: Add new port type for MediaTek BTIF controller on MT7622/23 SoC
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module called CONNSYS inside the SoC which could be mostly
found on those MediaTek SoCs with Bluetooth feature such as MT7622 and
MT7623 SoCs.

And the controller is made as being compatible with the 8250 register
layout with extra registers such as DMA enablement so it tends to be
integrated with reusing 8250 OF driver. However, DMA mode is not being
supported yet in the current driver.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:22 +02:00
Arvind Yadav 0d474f7fad tty: 8250: constify parisc_device_id
parisc_device_id are not supposed to change at runtime. All functions
working with parisc_device_id provided by <asm/parisc-device.h> work
with const parisc_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:20 +02:00
Franklin S Cooper Jr a2d23edaef serial: 8250_of: Add basic PM runtime support
66AK2G UART instances are not apart of the ALWAYS_ON power domain.
Therefore, pm_runtime calls must be made to properly insure the appropriate
power domains needed by UART are on. Keep legacy clk api calls since other
users of this driver may not support PM runtime.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:20 +02:00
Sergei Shtylyov 5c98e9cd45 serial: 8250_of: use of_property_read_bool()
Use slightly more compact of_property_read_bool() calls for the boolean
properties instead of of_find_property() calls.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:20 +02:00
Rafael Gago 6e0a5de213 serial: 8250: Use hrtimers for rs485 delays
Previously the timers where based on the classic timers, giving a too
coarse resolution on systems with configs of less than 1000 HZ.

This patch changes the rs485 timers to hrtimers.

Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:20 +02:00
Himanshu Jha d77dc47fce tty: serial: 8250_mtk: Use PTR_ERR_OR_ZERO
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 20:51:20 +02:00
Helge Deller 9e466f101e parisc/8250_gsc: Fix section mismatches
Signed-off-by: Helge Deller <deller@gmx.de>
2017-08-22 16:34:36 +02:00
Greg Kroah-Hartman cf0a1579dd Merge 4.13-rc5 into tty-next
We want the fixes in here, and we resolve the merge issue in the
8250_core.c file.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-14 14:46:59 -07:00
Linus Torvalds 438630ef5b tty/serial fixes for 4.13-rc5
Here are two tty serial driver fixes for 4.13-rc5.  One is a revert of a
 -rc1 patch that turned out to not be a good idea, and the other is a fix
 for the pl011 serial driver.
 
 Both have been in linux-next with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+1vw8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykreACeLI2spfagnOcnW264PGHxLMgj47EAn0JPSNIg
 5FLEtVsgxMuc8kc4LkDb
 =58g+
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
 "Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
  a -rc1 patch that turned out to not be a good idea, and the other is a
  fix for the pl011 serial driver.

  Both have been in linux-next with no reported issues"

* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: Delete dead code for CIR serial ports"
  tty: pl011: fix initialization order of QDF2400 E44
2017-08-13 12:33:35 -07:00
Sean Young 9527b82ae3 Revert "serial: Delete dead code for CIR serial ports"
This reverts commit 1104321a7b.

The code is not dead at all and breaks winbond-cir.

Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a CIR port
lirc lirc0: lirc_dev: driver ir-lirc-codec (winbond-cir) registered at minor = 0
winbond-cir 00:03: Region 0x2f8-0x2ff already in use!
winbond-cir: probe of 00:03 failed with error -16

Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-01 09:50:18 -07:00
Jan Kiszka a589e211bd gpio: exar: Use correct property prefix and document bindings
The device-specific property should be prefixed with the vendor name,
not "linux,", as Linus Walleij pointed out. Change this and document the
bindings of this platform device.

We didn't ship the old binding in a release yet. So we can still change
it without breaking an official API.

Fixes: 380b1e2f3a ("gpio-exar/8250-exar: Make set of exported GPIOs configurable")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-01 13:43:55 +02:00
Andy Shevchenko 7d8905d064 serial: 8250_pci: Enable device after we check black list
If the board we are guessing has been listed in black list we don't need
to enable it twice. The associated driver, if any, will take care about
proper initialization.

To achieve this we split out two helper functions, i.e.
serial_pci_is_class_communication() and serial_pci_is_blacklisted() which will
be called before pcim_enable_device(). We can do this since PCI specification
requires class, device and vendor ID registers to be always present in the
configuration space.

As an example what happens before this patch applied
(These are some debug prints, don't search for them in kernel sources):

	serial 0000:00:04.1: Mapped GSI28 to IRQ28
	serial 0000:00:04.2: Mapped GSI29 to IRQ29
	serial 0000:00:04.3: Mapped GSI54 to IRQ54
	8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
	8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
	8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54

After we will have just last three lines out of above.

	8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
	8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
	8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54

While here, correct a value of error code mentioned in the comment of
serial_pci_guess_board().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:44:55 -07:00
Andy Shevchenko c7ac15ce89 serial: core: move UPF_NO_TXEN_TEST to quirks and rename
First 16 bits in the flags field are user-visible except
UPF_NO_TXEN_TEST. To keep it clean we introduce internal quirks and move
UPF_NO_TXEN_TEST to them. Rename the constant to UPQ_NO_TXEN_TEST to
distinguish with port flags. Users are converted accordingly.

The quirks field might be extended later to hold the additional ones.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:44:22 -07:00
Jeffy Chen bdc4704b2d serial: 8250_early: Remove __init marking from early write
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.

So remove the __init marking to avoid invalid memory access.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:38:50 -07:00
Jeffy Chen 1b7eec2af6 serial: 8250_ingenic: Remove __init marking from early write
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.

So remove the __init marking to avoid invalid memory access.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:38:50 -07:00
Alexey Khoroshilov cbafe9d5c3 drivers/serial: Do not leave sysfs group in case of error in aspeed_vuart_probe()
There are several error handling paths in aspeed_vuart_probe(),
where sysfs group is left unremoved. The patch fixes them.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:37:25 -07:00
Philipp Zabel b382f5d3c3 serial: 8250_dw: explicitly request exclusive reset control
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:35:28 -07:00
Alexey Khoroshilov fa9ba3acb5 serial: 8250: fix error handling in of_platform_serial_probe()
clk_disable_unprepare(info->clk) is missed in of_platform_serial_probe(),
while irq_dispose_mapping(port->irq) is missed in of_platform_serial_setup().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:35:28 -07:00
Arvind Yadav c40f716ad3 tty: serial: pci: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
  12626	  18128	      0	  30754	   7822 tty/serial/8250/8250_pci.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
  23986	   6768	      0	  30754	   7822 tty/serial/8250/8250_pci.o

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:35:28 -07:00
Arvind Yadav 3637c46032 tty: serial: exar: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
   4030	   1280	      0	   5310	   14be	tty/serial/8250/8250_exar.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
   4958	    352	      0	   5310	   14be	tty/serial/8250/8250_exar.o

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30 07:35:28 -07:00
Linus Torvalds c7d28eca1d This is the bulk of GPIO changes for the v4.13 series:
Core:
 - Export add/remove for lookup tables so that modules can export GPIO
   descriptor tables.
 - Handle GPIO sleep states: it is now possible to flag that a GPIO line
   may loose its state during suspend/resume of the system to save
   power. This is used in the Wolfson Micro Arizona driver.
 - ACPI-based GPIO was tightened up a lot around the edges.
 - Use bitmap_fill() to speed up a loop.
 
 New drivers:
 - Exar XRA1403 SPI-based GPIO.
 - MVEBU driver now supports Armada 7K and 8K.
 - LP87565 PMIC GPIO.
 - Renesas R-CAR R8A7743 (RZ/G1M).
 - The new IOT2040 8250 serial/GPIO also comes in through this
   changeset.
 
 Substantial driver changes:
 - Seriously fix the Exar 8250 GPIO portions to work.
 - The MCP23S08 was moved out to a pin control driver.
 - Convert MEVEBU to use regmap for register access.
 - Drop Vulcan support from the Broadcom driver.
 - Serious cleanup and improvement of the mockup driver, giving us a
   better test coverage.
 
 Misc:
 - Lots of janitorial clean up.
 - A bunch of documentation fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJZX1MjAAoJEEEQszewGV1zEYUQALFsjJH7D2mRN4TSSEeVAcYr
 Uz52uupsou8tgW0IupRb/khO+V6zgd7j+kHDJLMxX+rCTw3pTq5+XGyi5+iNpxof
 TIIT1XBx4eq7Q/n4nWdGodHbHN9BXw7cGsNmTb1TS/G/6h1wOKxfzjvUNhDAC+2v
 idPy6B5G+WrDsYpBtTWlKHKQKVqbUlhLFyJYoglzqIeM5L9Ry/UoZ6sGleho3hKn
 Vlg/hMtkCexnVO9zopBe5CuEfseLrkcCgCvtQ713egzVXApryp4hqm3Xti20Ntgy
 OxnKhmVyloqd0kU0qLSpvDAf7B1invbHHbeZsag6wluTMrxgUYJONuonrqGeGiwB
 FBDtw9SGn2GlEXcs7sg8ANmAyr2XxxezKXD9XLBL5jadNB2KCY5yKMv1IK3VnYdq
 gEpFAiZ5cmlpZxIXqlyeZP6LKHNTci4amb33x1I/ghH2BTkGQ/3E3anXEbPNWF8G
 DDE6nrSgU0oQcNqRHyZaWNZpUIz4aFUgJtOEO4lYYP4+VzYSKTdrHseTiiJ91J7E
 WBz9p5JvSnB22+60RhyTAPjVjXgWa30nidf7WGCK0UHiIYffihCxGZRTlrhoEEUB
 fXgveJpqxLopYvxpUxi1OqlPYYo7zKRF5BzHsjKMpdVYXfdMdvs7eq2g/X889i1D
 WpbE9LyAH9FY5BM8YjFX
 =TpW1
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.13 series.

  Some administrativa:

  I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
  driver coming in through this tree, along with a whole bunch of Exar
  8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
  where they are ACKed by Andy Shevchenko.

  Speaking about drivers/platform/* there is also a bunch of ACPI stuff
  coming through that route, again ACKed by Andy.

  The MCP23S08 changes are coming in here as well. You already have the
  commits in your tree, so this is just a result of sharing an immutable
  branch between pin control and GPIO.

  Core:
   - Export add/remove for lookup tables so that modules can export GPIO
     descriptor tables.
   - Handle GPIO sleep states: it is now possible to flag that a GPIO
     line may loose its state during suspend/resume of the system to
     save power. This is used in the Wolfson Micro Arizona driver.
   - ACPI-based GPIO was tightened up a lot around the edges.
   - Use bitmap_fill() to speed up a loop.

  New drivers:
   - Exar XRA1403 SPI-based GPIO.
   - MVEBU driver now supports Armada 7K and 8K.
   - LP87565 PMIC GPIO.
   - Renesas R-CAR R8A7743 (RZ/G1M).
   - The new IOT2040 8250 serial/GPIO also comes in through this
     changeset.

  Substantial driver changes:
   - Seriously fix the Exar 8250 GPIO portions to work.
   - The MCP23S08 was moved out to a pin control driver.
   - Convert MEVEBU to use regmap for register access.
   - Drop Vulcan support from the Broadcom driver.
   - Serious cleanup and improvement of the mockup driver, giving us a
     better test coverage.

  Misc:
   - Lots of janitorial clean up.
   - A bunch of documentation fixes"

* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
  serial: exar: Add support for IOT2040 device
  gpio-exar/8250-exar: Make set of exported GPIOs configurable
  platform: Accept const properties
  serial: exar: Factor out platform hooks
  gpio-exar/8250-exar: Rearrange gpiochip parenthood
  gpio: exar: Fix iomap request
  gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
  serial: uapi: Add support for bus termination
  gpio: rcar: Add R8A7743 (RZ/G1M) support
  gpio: gpio-wcove: Fix GPIO control register offset calculation
  gpio: lp87565: Add support for GPIO
  gpio: dwapb: fix missing first irq for edgeboth irq type
  MAINTAINERS: Take maintainership for GPIO ACPI support
  gpio: exar: Fix reading of directions and values
  gpio: exar: Allocate resources on behalf of the platform device
  gpio-exar/8250-exar: Fix passing in of parent PCI device
  gpio: mockup: use devm_kcalloc() where applicable
  gpio: mockup: add myself as author
  gpio: mockup: improve the error message
  gpio: mockup: don't return magic numbers from probe()
  ...
2017-07-07 12:40:27 -07:00
Jan Kiszka 413058df43 serial: exar: Add support for IOT2040 device
This implements the setup of RS232 and the switch-over to RS485 or RS422
for the Siemens IOT2040. That uses an EXAR XR17V352 with external logic
to switch between the different modes. The external logic is controlled
via MPIO pins of the EXAR controller.

Only pin 10 can be exported as GPIO on the IOT2040. It is connected to
an LED.

As the XR17V352 used on the IOT2040 is not equipped with an external
EEPROM, it cannot present itself as IOT2040-variant via subvendor/
subdevice IDs. Thus, we have to check via DMI for the target platform.

Co-developed with Sascha Weisenberger.

Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-03 08:33:20 +02:00
Jan Kiszka 380b1e2f3a gpio-exar/8250-exar: Make set of exported GPIOs configurable
On the SIMATIC, IOT2040 only a single pin is exportable as GPIO, the
rest is required to operate the UART. To allow modeling this case,
expand the platform device data structure to specify a (consecutive) pin
subset for exporting by the gpio-exar driver.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
2017-07-03 08:32:42 +02:00
Jan Kiszka 0d963ebf57 serial: exar: Factor out platform hooks
This prepares the addition of IOT2040 platform support by preparing the
needed setup and rs485_config hooks.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-03 08:30:54 +02:00
Jan Kiszka 4076cf08ac gpio-exar/8250-exar: Rearrange gpiochip parenthood
Set the parent of the exar gpiochip to its platform device, like other
gpiochips are doing it. In order to keep the relationship discoverable
for ACPI systems, set the platform device companion to the PCI device.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2017-07-03 08:30:51 +02:00
Jan Kiszka a39f2fe716 gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
Commtech adapters need the MPIOs for internal purposes, and the
gpio-exar driver already refused to pick them up. But there is actually
no point in even creating the underlying platform device.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-03 08:23:09 +02:00
Vignesh R a1bfb6eb30 serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
DMA RX completion handler for UART is called from a tasklet and hence
may be delayed depending on the system load. In meanwhile, there may be
RX timeout interrupt which can get serviced first before DMA RX
completion handler is executed for the completed transfer.
omap_8250_rx_dma_flush() which is called on RX timeout interrupt makes
sure that the DMA RX buffer is pushed and then the FIFO is drained and
also queues a new DMA request. But, when DMA RX completion handler
executes, it will erroneously flush the currently queued DMA transfer
which sometimes results in data corruption and double queueing of DMA RX
requests.

Fix this by checking whether RX completion is for the currently queued
transfer or not. And also hold port lock when in DMA completion to avoid
race wrt RX timeout handler preempting it.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-29 17:03:10 +02:00
Phil Elwell cfde770d94 serial: 8250: Fix THRE flag usage for CAP_MINI
The BCM2835 MINI UART has non-standard THRE semantics. Conventionally
the bit means that the FIFO is empty (although there may still be a
byte in the transmit register), but on 2835 it indicates that the FIFO
is not full. This causes interrupts after every byte is transmitted,
with the FIFO providing some interrupt latency tolerance.

A consequence of this difference is that the usual strategy of writing
multiple bytes into the TX FIFO after checking THRE once is unsafe.
In the worst case of 7 bytes in the FIFO, writing 8 bytes loses all
but the first since by then the FIFO is full.

There is an HFIFO ("Hidden FIFO") capability that causes the transmit
loop to terminate when both THRE and TEMT are set, i.e. when the TX
block is completely idle. This is unnecessarily cautious, potentially
causing gaps in transmission.

Add a new conditional to the transmit loop, predicated on CAP_MINI,
that exits when THRE is no longer set (the FIFO is full). This allows
the FIFO to fill quickly but subsequent writes are paced by the
transmission rate.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-29 17:03:10 +02:00
Jan Kiszka d3936d7437 gpio-exar/8250-exar: Fix passing in of parent PCI device
This fixes reloading of the GPIO driver for the same platform device
instance as created by the exar UART driver: First of all, the driver
sets drvdata to its own value during probing and does not restore the
original value on exit. But this won't help anyway as the core clears
drvdata after the driver left.

Set the platform device parent instead.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-20 10:12:39 +02:00
Matthias Brugger 1104321a7b serial: Delete dead code for CIR serial ports
Commit e4fda3a042 ("serial: don't register CIR serial ports") adds a
check for PORT_8250_CIR to serial8250_register_8250_port(). But the code
isn't needed as the function never takes the branch when the port is CIR
serial port.

This patch deletes the dead code.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-20 10:24:15 +08:00
Jan Kiszka bea8be6561 serial: exar: Leave MPIOs as output for Commtech adapters
Commtech adapters apparently need the original setting as outputs, see
https://marc.info/?l=linux-gpio&m=149557425201323&w=2. Account for that.

Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-09 11:23:36 +02:00
Joel Stanley e2860e1f62 serial: 8250_of: Add reset support
This adds the hooks for an optional reset controller in the 8250 device
tree node.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-03 18:48:52 +09:00
Greg Kroah-Hartman aa668632ae Merge 4.12-rc3 into tty-next
We need the tty fixes/changes here to handle future work.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-29 08:18:15 +02:00
Phil Elwell d087e7a991 serial: 8250: Add CAP_MINI, set for bcm2835aux
The AUX/mini-UART in the BCM2835 family of procesors is a cut-down
8250 clone. In particular it is lacking support for the following
features: CSTOPB PARENB PARODD CMSPAR CS5 CS6

Add a new capability (UART_CAP_MINI) that exposes the restrictions to
the user of the termios API by turning off the unsupported features in
the request.

N.B. It is almost possible to automatically discover the missing
features by reading back the LCR register, but the CSIZE bits don't
cooperate (contrary to the documentation, both bits are significant,
but CS5 and CS6 are mapped to CS7) and the code is much longer.

See: https://github.com/raspberrypi/linux/issues/1561

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-24 15:15:56 +02:00
Jan Kiszka 2c0ac5b48a serial: exar: Fix stuck MSIs
After migrating 8250_exar to MSI in 172c33cb61, we can get stuck
without further interrupts because of the special wake-up event these
chips send. They are only cleared by reading INT0. As we fail to do so
during startup and shutdown, we can leave the interrupt line asserted,
which is fatal with edge-triggered MSIs.

Add the required reading of INT0 to startup and shutdown. Also account
for the fact that a pending wake-up interrupt means we have to return 1
from exar_handle_irq. Drop the unneeded reading of INT1..3 along with
this - those never reset anything.

An alternative approach would have been disabling the wake-up interrupt.
Unfortunately, this feature (REGB[17] = 1) is not available on the
XR17D15X.

Fixes: 172c33cb61 ("serial: exar: Enable MSI support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18 16:43:55 +02:00
Ard Biesheuvel 4c4fc90964 drivers/tty: 8250: only call fintek_8250_probe when doing port I/O
Commit fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
modified the probing logic for PNP0501 devices, to remove a collision
between the generic 16550A driver and the Fintek driver, which reused
the same ACPI _HID.

The Fintek device probe is now incorporated into the common 8250 probe
path, and gets called for all discovered 16550A compatible devices,
including ones that are MMIO mapped rather than IO mapped. However,
the Fintek driver assumes the port base is a I/O address, and proceeds
to probe some arbitrary offsets above it.

This is generally a wrong thing to do, but on ARM systems (having no
native port I/O), this may result in faulting accesses of completely
unrelated MMIO regions in the PCI I/O space. Given that this is at
serial probe time, this results in hard to diagnose crashes at boot.

So let's restrict the Fintek probe to devices that we know are using
port I/O in the first place.

Fixes: fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18 16:39:10 +02:00
Jan Kiszka 7dea8165f1 serial: exar: Preconfigure xr17v35x MPIOs as output
This is the safe default for GPIOs with unknown external wiring.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18 16:26:40 +02:00
Jeremy Kerr 7fbcf3afe6 drivers/serial: Add driver for Aspeed virtual UART
This change adds a driver for the 16550-based Aspeed virtual UART
device. We use a similar process to the of_serial driver for device
probe, but expose some VUART-specific functions through sysfs too.

The VUART is two UART 'front ends' connected by their FIFO (no actual
serial line in between). One is on the BMC side (management controller)
and one is on the host CPU side.

This driver is for the BMC side. The sysfs files allow the BMC
userspace, which owns the system configuration policy, to specify at
what IO port and interrupt number the host side will appear to the host
on the Host <-> BMC LPC bus. It could be different on a different system
(though most of them use 3f8/4).

OpenPOWER host firmware doesn't like it when the host-side of the
VUART's FIFO is not drained. This driver only disables host TX discard
mode when the port is in use. We set the VUART enabled bit when we bind
to the device, and clear it on unbind.

We don't want to do this on open/release, as the host may be using this
bit to configure serial output modes, which is independent of whether
the devices has been opened by BMC userspace.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18 16:19:16 +02:00
Joel Stanley ea5244e2af serial: 8250: Add flag so drivers can avoid THRE probe
The probing of THRE irq behaviour assumes the other end will be reading
bytes out of the buffer in order to probe the port at driver init. In
some cases the other end cannot be relied upon to read these bytes, so
provide a flag for them to skip this step.

Bit 19 was chosen as the flags are a int and the top bits are taken.

Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18 16:19:16 +02:00
Andy Shevchenko 70b2fe355a serial: 8250_exar: Remove duplicate assignment
UPF_EXAR_EFR is set globally for each port enumerated by the driver.
Thus, no need to repeat this in individual ->setup() hook.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18 16:19:16 +02:00
Vignesh R 84b40e3b57 serial: 8250: omap: Disable DMA for console UART
Kernel always writes log messages to console via
serial8250_console_write()->serial8250_console_putchar() which directly
accesses UART_TX register _without_ using DMA.

But, if other processes like systemd using same UART port, then these
writes are handled by a different code flow using 8250_omap driver where
there is provision to use DMA.

It seems that it is possible that both DMA and CPU might simultaneously
put data to UART FIFO and lead to potential loss of data due to FIFO
overflow and weird data corruption. This happens when both kernel
console and userspace tries to write simultaneously to the same UART
port. Therefore, disable DMA on kernel console port to avoid potential
race between CPU and DMA.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18 16:19:16 +02:00
Linus Torvalds 291b38a756 Annotation of module parameters that specify device settings
-----BEGIN PGP SIGNATURE-----
 
 iQIVAwUAWPiW6vSw1s6N8H32AQLOrw/+NTqGf7bjq+64YKS6NfR0XDgE+wNJltGO
 ck7zJW3NHIg76RNu8s0I9xg5aVmwizz3Z5DGROZquaolnezux4tQihZ3AFyxIzLc
 +Y3WHYagcML7yFfjl/WznCLRD5EW3yPln4lCvQO0nW/xICRYeRI057JaIbi2Dtek
 BhcXt3c4AjXDLdYJkgtHV3p2R2mt8hcdFdWqqx6s7JaIThZNRGNzxAgtbcB9k5IW
 HVG9ZEIL73VBYWHrYivzjHYF5rBnNCPt87eOwDQeTOSkhv8te+u9k+bH8vxZw1T0
 XUtDrLBndKiuVo2GUfLkkF8LItx3Q9eLCJYy0joaIliyPqTEsPx9KjQ+Af0cxS9s
 ZPCZ5SYf96stKmDeL5xaMfrAmeyVHJ4lc4JTOqdzbIT8blsOSfYO/03p0ALShSDv
 /RQLaKGlf8Bjoy8PwKFcXb4sIDufcd/U1Av/EMFXxOfgN/u2JUkGKq6EaIM5B68L
 fHPje+aR9VNELPmPjwNOWtmN4I79EH3EItQf7zv0KG+UeKhcHLx/EAcSJ3ZRKEkH
 Lathg7pPOEJGArPiVO79TZzBG01ADn1aiwv65XObMzNZ+54xI/mN/Y1DNF/kL5jU
 XzvNzEjFt8mwMIZGVNdAt4+pDyMfIZGZSyUkSRKFnaQZMIvQrfQIU9RLBYLX5eOx
 +/p0VkIwDpg=
 =lbS7
 -----END PGP SIGNATURE-----

Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull hw lockdown support from David Howells:
 "Annotation of module parameters that configure hardware resources
  including ioports, iomem addresses, irq lines and dma channels.

  This allows a future patch to prohibit the use of such module
  parameters to prevent that hardware from being abused to gain access
  to the running kernel image as part of locking the kernel down under
  UEFI secure boot conditions.

  Annotations are made by changing:

        module_param(n, t, p)
        module_param_named(n, v, t, p)
        module_param_array(n, t, m, p)

  to:

        module_param_hw(n, t, hwtype, p)
        module_param_hw_named(n, v, t, hwtype, p)
        module_param_hw_array(n, t, hwtype, m, p)

  where the module parameter refers to a hardware setting

  hwtype specifies the type of the resource being configured. This can
  be one of:

        ioport          Module parameter configures an I/O port
        iomem           Module parameter configures an I/O mem address
        ioport_or_iomem Module parameter could be either (runtime set)
        irq             Module parameter configures an I/O port
        dma             Module parameter configures a DMA channel
        dma_addr        Module parameter configures a DMA buffer address
        other           Module parameter configures some other value

  Note that the hwtype is compile checked, but not currently stored (the
  lockdown code probably won't require it). It is, however, there for
  future use.

  A bonus is that the hwtype can also be used for grepping.

  The intention is for the kernel to ignore or reject attempts to set
  annotated module parameters if lockdown is enabled. This applies to
  options passed on the boot command line, passed to insmod/modprobe or
  direct twiddling in /sys/module/ parameter files.

  The module initialisation then needs to handle the parameter not being
  set, by (1) giving an error, (2) probing for a value or (3) using a
  reasonable default.

  What I can't do is just reject a module out of hand because it may
  take a hardware setting in the module parameters. Some important
  modules, some ipmi stuff for instance, both probe for hardware and
  allow hardware to be manually specified; if the driver is aborts with
  any error, you don't get any ipmi hardware.

  Further, trying to do this entirely in the module initialisation code
  doesn't protect against sysfs twiddling.

  [!] Note that in and of itself, this series of patches should have no
      effect on the the size of the kernel or code execution - that is
      left to a patch in the next series to effect. It does mark
      annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
      an already existing field"

* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
  Annotate hardware config module parameters in sound/pci/
  Annotate hardware config module parameters in sound/oss/
  Annotate hardware config module parameters in sound/isa/
  Annotate hardware config module parameters in sound/drivers/
  Annotate hardware config module parameters in fs/pstore/
  Annotate hardware config module parameters in drivers/watchdog/
  Annotate hardware config module parameters in drivers/video/
  Annotate hardware config module parameters in drivers/tty/
  Annotate hardware config module parameters in drivers/staging/vme/
  Annotate hardware config module parameters in drivers/staging/speakup/
  Annotate hardware config module parameters in drivers/staging/media/
  Annotate hardware config module parameters in drivers/scsi/
  Annotate hardware config module parameters in drivers/pcmcia/
  Annotate hardware config module parameters in drivers/pci/hotplug/
  Annotate hardware config module parameters in drivers/parport/
  Annotate hardware config module parameters in drivers/net/wireless/
  Annotate hardware config module parameters in drivers/net/wan/
  Annotate hardware config module parameters in drivers/net/irda/
  Annotate hardware config module parameters in drivers/net/hamradio/
  Annotate hardware config module parameters in drivers/net/ethernet/
  ...
2017-05-10 19:13:03 -07:00
David Howells 3b60daf86b Annotate hardware config module parameters in drivers/tty/
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image.  Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.

To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify.  The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.

Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.

This patch annotates drivers in drivers/tty/.

Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jiri Slaby <jslaby@suse.com>
cc: linux-serial@vger.kernel.org
2017-04-20 12:02:32 +01:00
Marc Gonzalez 72f1b85a04 serial: 8250_early: Add earlycon support for Palmchip UART
Define an OF early console for Palmchip UART, which can be enabled
by passing "earlycon" on the boot command line.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-04-18 17:47:42 +02:00
Greg Kroah-Hartman 9ccd8d7445 Merge 4.11-rc5 into tty-next
We want the serial fixes in here as well to handle merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-04-03 14:18:16 +02:00
Paul Gortmaker 49e1590c2e serial: 8250_EXAR: fix duplicate Kconfig text and add missing help text
In commit d0aeaa83f0 ("serial: exar:
split out the exar code from 8250_pci") the exar driver got its own
Kconfig.  However the text for the new option was never changed from
the original 8250_PCI text, and hence it appears confusing when you
get asked the same question twice:

  8250/16550 PCI device support (SERIAL_8250_PCI) [Y/n/m/?] (NEW)
    8250/16550 PCI device support (SERIAL_8250_EXAR) [Y/n/m] (NEW)

Adding to the confusion, is that there is no help text for this new
option to indicate it is specific to a certain family of cards.

Fix both issues at the same time, as well as the space vs. tab issues
introduced in the same commit.

Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-31 17:26:20 +02:00
Vignesh R b2c663d155 serial: 8250: 8250_core: Fix irq name for 8250 serial IRQ
Using dev_name() as IRQ name during request_irq() might be misleading in
case of serial over PCI. Therefore identify serial port IRQ using
uart_port's name field. This will help mapping IRQs to appropriate
ttySN(where N is the serial port index) instances.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-31 16:56:10 +02:00
Jan Kiszka 7cd3e9dbdd serial: 8250_lpss: Unconditionally set PCI master for Quark
MSI needs it as well.

Should have no practical impact, though, as DMA is always available on
the Quark. But given the few users of pci_alloc_irq_vectors so far, this
incorrect pattern may spread otherwise.

Fixes: 3f3a46951e ("serial: 8250_lpss: set PCI master only for private DMA")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-31 15:36:54 +02:00
Greg Kroah-Hartman 53c1cf4281 Merge 4.11-rc4 into tty-next
We want the tty/serial fixes in here to handle bugfixes and merge
issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-29 08:58:53 +02:00
Philipp Zabel acbdad8dd1 serial: 8250_dw: simplify optional reset handling
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.

This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-17 14:17:12 +09:00
Lukas Redlinger fab8a02b73 serial: 8250_fintek: Enable high speed mode on Fintek F81866
Fintek F81866 supports baud rates higher than 115200 but needs to raise
it's clock speed from 1.84 to 14.76 MHz.
This is eight times faster, so gives 921600 as resulting baud_base.

F81866 clock register 0xf2:
    Bit 7-2    reserved
    Bit 1-0    00: 1.8432MHz
               01: 18.432MHz
               10: 24MHz
               11: 14.769MHz

Signed-off-by: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-17 14:17:11 +09:00
Vignesh R f48180a70e serial: 8250: 8250_core: Use dev_name() during request_irq()
Passing "serial" as name during request_irq() results in all serial port
irqs have same name. This does not help much to easily identify which
irq belongs to which serial port instance. Therefore pass dev_name()
during request_irq() so that better identifiable name is listed for
serial ports in cat /proc/interrupts output.

Output of cat /proc/interrupts
Before this patch:
 26:        689          0     GICv2 309 Edge      serial
After this patch:
 26:        696          0     GICv2 309 Edge      2530c00.serial

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-14 11:01:40 +08:00
Andy Shevchenko 2b57b7ff9d serial: 8250_exar: Fix spelling of "driver"
Fix typo in "Dricer".

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-14 10:59:04 +08:00
James Hogan b15bfbe642 serial: 8250_dw: Fix breakage when HAVE_CLK=n
Commit 6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be
used") recently broke the 8250_dw driver on platforms which don't select
HAVE_CLK, as dw8250_set_termios() gets confused by the behaviour of the
fallback HAVE_CLK=n clock API in linux/clk.h which pretends everything
is fine but returns (valid) NULL clocks and 0 HZ clock rates.

That 0 rate is written into the uartclk resulting in a crash at boot,
e.g. on Cavium Octeon III based UTM-8 we get something like this:

1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 41, base_baud = 25000000) is a OCTEON
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1 at drivers/tty/serial/serial_core.c:441 uart_get_baud_rate+0xfc/0x1f0
...
Call Trace:
...
[<ffffffff8149c2e4>] uart_get_baud_rate+0xfc/0x1f0
[<ffffffff814a5098>] serial8250_do_set_termios+0xb0/0x440
[<ffffffff8149c710>] uart_set_options+0xe8/0x190
[<ffffffff814a6cdc>] serial8250_console_setup+0x84/0x158
[<ffffffff814a11ec>] univ8250_console_setup+0x54/0x70
[<ffffffff811901a0>] register_console+0x1c8/0x418
[<ffffffff8149f004>] uart_add_one_port+0x434/0x4b0
[<ffffffff814a1af8>] serial8250_register_8250_port+0x2d8/0x440
[<ffffffff814aa620>] dw8250_probe+0x388/0x5e8
...

The clock API is defined such that NULL is a valid clock handle so it
wouldn't be right to check explicitly for NULL. Instead treat a
clk_round_rate() return value of 0 as an error which prevents uartclk
being overwritten.

Fixes: 6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-serial@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: bcm-kernel-feedback-list@broadcom.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jason Uy <jason.uy@broadcom.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-14 10:48:11 +08:00
Heiko Stuebner 09498087f9 serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios
clk_round_rate returns a signed long and may possibly return errors
in it, for example if there is no possible rate.

Till now dw8250_set_termios ignored any error, the signednes and would
just use the value as input to clk_set_rate. This of course falls apart
if there is an actual error, so check for errors and only try to set
a rate if the value is actually valid.

This turned up on some Rockchip platforms after commit
6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
enabled set_termios callback in all cases, not only ACPI.

Fixes: 6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-14 10:48:11 +08:00
Jan Kiszka 172c33cb61 serial: exar: Enable MSI support
Use pci_alloc_irq_vectors to enable MSI when available. At least the
XR17V352 supports this.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:13:26 +01:00
Jan Kiszka 7e12357ed6 serial: exar: Move register defines from uapi header to consumer site
None of these registers is relevant for the userspace API.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:13:26 +01:00
Jan Kiszka 0d560a1d54 serial: pci: Remove unused pci_boards entries
Became obsolete with the split-out of 8250_exar.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:12:39 +01:00
Jan Kiszka fc6cc96157 serial: exar: Move Commtech adapters to 8250_exar as well
Those are Exar-based, too.

With the required refactoring of the code to fit into 8250_exar, we
automatically fix the same issue pci_xr17v35x_setup had before: 8XMODE,
FCTL, TXTRG and RXTRG were always only set for port 0. Now they are
initialized for the correct target port by using port.membase.

Now we can also cleanly fix the blacklist of 8250_pci so that all
Commtech devices are rejected and 8250_exar can handle them.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:12:38 +01:00
Jan Kiszka 5b5f252d67 serial: exar: Fix initialization of EXAR registers for ports > 0
So far, pci_xr17v35x_setup always initialized 8XMODE, FCTR & Co. for
port 0 because it used the address of that port instead of moving the
pointer according to the port number. Fix this and remove the unneeded
temporary ioremap by moving default_setup up and reusing the membase it
fills into the port structure.

Fixes: 14faa8cce8 ("tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:12:38 +01:00
Jan Kiszka 24572af4fb serial: exar: Fix mapping of port I/O resources
pcim_iomap_table only returns the table of mapping, it does not perform
them. For that, we need to call pcim_iomap, but only if that mapping was
not done before.

Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:12:38 +01:00
Douglas Anderson 424d79183a serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
On a Rockchip rk3399-based board during suspend/resume testing, we
found that we could get the console UART into a state where it would
print this to the console a lot:
  serial8250: too much work for irq42

Followed eventually by:
  NMI watchdog: BUG: soft lockup - CPU#0 stuck for 11s!

Upon debugging I found that we're in this state:
  iir = 0x000000cc
  lsr = 0x00000060

It appears that somehow we have a RX Timeout interrupt but there is no
actual data present to receive.  When we're in this state the UART
driver claims that it handled the interrupt but it actually doesn't
really do anything.  This means that we keep getting the interrupt
over and over again.

Normally we don't actually need to do anything special to handle a RX
Timeout interrupt.  We'll notice that there is some data ready and
we'll read it, which will end up clearing the RX Timeout.  In this
case we have a problem specifically because we got the RX TImeout
without any data.  Reading a bogus byte is confirmed to get us out of
this state.

It's unclear how exactly the UART got into this state, but it is known
that the UART lines are essentially undriven and unpowered during
suspend, so possibly during resume some garbage / half transmitted
bits are seen on the line and put the UART into this state.

The UART on the rk3399 is a DesignWare based 8250 UART.  From mailing
list posts, it appears that other people have run into similar
problems with DesignWare based IP.  Presumably this problem is unique
to that IP, so I have placed the workaround there to avoid possibly of
accidentally triggering bad behavior on other IP.  Also note the RX
Timeout behaves very differently in the DMA case, for for now the
workaround is only applied to the non-DMA case.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:10:16 +01:00
Wei Yongjun 80cd94e759 serial: 8250_pci: make pciserial_detach_ports() static
Fixes the following sparse warning:

drivers/tty/serial/8250/8250_pci.c:3916:6: warning:
 symbol 'pciserial_detach_ports' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-09 13:54:49 +01:00
Ian Abbott 1c9c858e2f serial: 8250_pci: Add MKS Tenta SCOM-0800 and SCOM-0801 cards
The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively.  The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954.  The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-06 09:47:52 +01:00
Sudip Mukherjee 5d1a2388ed serial: 8250_pci: remove exar code
Remove the Exar specific codes from 8250_pci and blacklist those chips
so that the new Exar serial driver binds to the devices.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-03 10:12:16 +01:00
Sudip Mukherjee d0aeaa83f0 serial: exar: split out the exar code from 8250_pci
Add the serial driver for the Exar chips. And also register the
platform device for the GPIO provided by the Exar chips.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-03 10:12:16 +01:00
Arnd Bergmann aa42db44f6 8250: of: remove remnants of generic of_serial driver
During build testing, I ran into a warning in a driver that I
had written myself at some point:

drivers/tty/serial/8250/8250_of.c: In function 'of_platform_serial_probe':
drivers/tty/serial/8250/8250_of.c:233:1: error: the frame size of 1200 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]

This is harmless by itself, but it shows two other problems in
the driver:

- It still tries to be generic enough to handle all kinds of serial
  ports, where in reality the driver has been 8250-only for a while,
  and every other uart has its own DT support

- As a result of that generalization, we keep two copies of
  'struct uart_port' on the stack during probe(). This is completely
  unnessary.

Removing the last code dealing with unsupported port_type values
solves both problems nicely, and reduces the stack size.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-27 09:23:36 +01:00
Tony Lindgren 4e0f5cc650 serial: 8250_omap: Fix probe and remove for PM runtime
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:

omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?

Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().

Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-25 11:08:30 +01:00
Paul Gortmaker f99b63afb9 serial: hp300: mask the warning for people just doing build coverage
Currently this warning is triggered for allmodconfig on m68k.  It is
well intentioned, in that if you are building the driver but not
enabling one of the platforms where the hardware exists, you get a
warning.

The warning dates back to pre-git days, and now we have COMPILE_TEST
so we can use that to mask the warning for people who are obviously
just doing build coverage on tree wide changes.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-25 11:08:30 +01:00
Vignesh R aa75941ca1 serial: 8250_omap: Remove rx_dma_broken flag
8250 UART DMA support was marked broken by default as it was not
possible to pause ongoing RX DMA transfer. Now that both SDMA and
EDMA can support pause operation for RX DMA transactions, don't set
rx_dma_broken to true by default. With this patch 8250_omap driver will
use DMA by default.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-20 14:44:37 +01:00
Vignesh R b6ffcf2108 serial: 8250_omap: Add OMAP_DMA_TX_KICK quirk for AM437x
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-20 14:44:37 +01:00
Vignesh R 75f54acc08 serial: 8250_omap: pause DMA only if DMA transfer in progress
It is possible that DMA transfer is already complete but, completion
handler is yet to be called, when dmaengine_pause() is called in case of
error condition(like break/rx timeout). This leads to dmaengine_pause()
API to return EINVAL (as descriptor is already NULL) causing
rx_dma_broken flag to be set and effectively disabling RX DMA.
Fix this by calling dmaengine_pause() only when transfer is in progress.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-20 14:44:37 +01:00
Arvind Yadav 2cc32b18d1 tty: serial: 8250: 8250_gsc:- Handle return NULL error from ioremap_nocache
Here, If ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-19 14:20:23 +01:00
Andy Shevchenko 216e234d66 serial: 8250_mid: set PCI master only for DMA capable device
There is no need to set PCI bus mastering when device is not doing any DMA. It
includes MSI type of interrupts. Currently only UART on Denverton, which is DMA
capable, might have MSI enabled.

Taking above into account enable bus mastering for Denverton case only.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-19 14:20:23 +01:00