Describe all memebers in struct exar8250_board, otherwise we get a warning:
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'has_slave' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'setup' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'exit' not described in 'exar8250_board'
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar UARTs by default supports only up to 8 channels,
all above go as extension. Thus, there is no need to have
an additional property to distinguish them from first ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas RZ/N1 UART is based on the Synopsys DW UART, but has additional
registers for DMA. This patch does not address the changes required for DMA
support, it simply adds the compatible string.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the IRQ controller is not yet probed do not proceed with irq=0,
try to defer the probe.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't dispose IRQ mapping before it has been created.
Fixes: aa9594740 ("serial: 8250_of: Add IO space support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register. The fractional divisor width is
4bits ~ 6bits.
Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups dw specific get_divisor() and set_divisor() hook.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers could call serial8250_do_set_divisor() to complete its
own set_divisor routine. Export this symbol for code reusing.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add these two hooks so that they can be overridden with driver specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several extended (in comparison to the traditional 16550)
registers are present in Synopsys DesignWare UART. All of them
are 32-bit ones.
Introduce helpers to simplify access to them and convert existing users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align serial8250_get_divisor() with serial8250_set_divisor() to accept
uart_port pointer as the first parameter. No functionality changes.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the commit
7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.
So, remove the entries from blacklist in order to get cards enumerated.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Matt Turner <mattst88@gmail.com>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pcmcia_loop_config fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pcmcia_loop_config.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM654 uses a UART controller that is compatible (partially) with
existing 8250 UART, however, has a few differences with respect to DMA
support and control paths. Introduce a base definition that allows us
to build up the differences in follow on patches.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the non-board-specific part of the RS485 initialization from
iot2040_rs485_config function to a new generic function used also for
other boards.
This allows using TIOCGRS485 and TIOCSRS485 on boards (such as mPCIe
serial IO modules) which are hard-wired to RS485 or have jumpers for
their configurations.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using kgdb, you get an abort when accessing the UART registers.
This is because the driver has already entered runtime PM and so turned
off the bus clock needed to access the registers.
To fix this, set the capability indicating Runtime PM is active while idle.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.
After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.
This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.
Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.
Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.
And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.
Fixes: cdb929e445 ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Altera 16550 UART core supports FCR Rx Trigger Level setting,
but the port definition in the driver is missing the rxtrig_bytes
array specifying the trigger levels. Add the array to make the Rx
Trigger Level setting available on this type of 16550 UART.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "unthrottle_timeout" is HZ/10 but mod_timer() takes a the actual
jiffie where you want it to timeout, not an offset.
Fixes: 5909c0bf9c ("serial/aspeed-vuart: Implement quick throttle mechanism")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the 8250_of driver only supports MEM IO type
accesses.
Some development boards (Huawei D03, specifically) require
IO space access for 8250-compatible OF driver support, so
add it.
The modification is quite simple: just set the port iotype
and associated flags depending on the device address
resource type.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device->baud is always non zero value because it is checked already in
early_serial8250_setup() before init_port is called.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although we populate the ->throttle and ->unthrottle UART operations,
these may not be called until the ldisc has had a chance to schedule and
check buffer space. This means that we may overflow the flip buffers
without ever hitting the ldisc's throttle threshold.
This change implements an interrupt-based throttle, where we check for
space in the flip buffers before reading characters from the UART's
FIFO. If there's no space available, we disable the RX interrupt and
schedule a timer to check for space later.
For this, we need an unlocked version of the set_throttle function to be
able to change throttle state from the irq_handler, which already holds
port->lock.
This prevents a case where we drop characters under heavy RX load.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aspeed VUART runs at LPC bus frequency, rather than being restricted
to a typical UART baud rate. This means that the VUART can receive a lot
of data, which can overrun tty flip buffers, and/or cause a large amount
of interrupt traffic.
This change implements the uart_port->throttle & unthrottle callbacks,
implemented by disabling the receiver line status & received data
available IRQs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we export serial8250_rx_chars, which does a whole bunch of
reads from the 8250 data register, without any form of flow control
between reads.
An upcoming change to the aspeed vuart driver implements more
fine-grained flow control in the interrupt handler, requiring
character-at-a-time control over the rx path.
This change exports serial8250_read_char to allow this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.
This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling rountines himself.
Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.
Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.
Example stacktrace by performing echo 1 > /dev/ttyS2 on a non-patched system:
|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable/Clear module level UART wakeup in UART_OMAP_WER register based on
return value of device_may_wakeup() in .suspend(). This allows
userspace to use sysfs to control the ability of UART to wakeup the
system from deep sleep state. Register is restored back in .startup()
call that happens as part of resume sequence.
With this patch, userspace can control UART wakeup capability via sysfs:
To enable wakeup capability:
echo enabled > /sys/class/tty/ttyXX/device/power/wakeup
For disabling wakeup capability:
echo disabled > /sys/class/tty/ttyXX/device/power/wakeup
Note that the UART wakeup events configured in the 8250 hardware only
work for idle modes that do not cut off power for the UART. For deeper
idle states, dedicated padconf wakeirqs must be used. Or in some cases
the UART RX pin can be remuxed to GPIO input if the GPIO block stays
powered.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous implementation has had a detrimental effect on devices using
high bitrates (bluetooth), as the fifo being non-empty for a single check
would result in a 10 µs delay.
Limit the change to devices with the new "marvell,armada-38x-uart"
compatible string. Also update the code to allow the first 1000 retries
to not perform a delay.
The maximum duration of retries has been increased to cover a worst-case
seen on the Armada 385 SoC. "dmesg ; resize", will fill the buffer with
text to output before doing a resize. At 9600 baud this took up to 13 ms
to flush all characters and avoid some getting lost.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for two MEN UARTs (16z025 and 16z057) to the
8250_men_mcb driver.
The 16z025 consists of up to four ports, the 16z057 has
exactly four ports. Apart from that, all of them share the
Port settings.
Signed-off-by: Michael Moese <mmoese@suse.de>
Reported-by: Ben Turner <ben.turner@21net.com>
Tested-by: Ben Turner <ben.turner@21net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Special settings for APMC0D08 are applied when device is present
in the system. To check its presence we may use acpi_dev_present()
instead of current open coded variant.
Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI ID database is for IDs used across several drivers.
Here is the case for SUNIX combo cards.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI ids for two variants of Brainboxes UC-260 quad port
PCI serial cards.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not fail on multiport cards in serial_pci_is_class_communication().
It restores behaviour for SUNIX multiport cards, that enumerated by
class and have a custom board data.
Moreover it allows users to reenumerate port-by-port from user space.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An issue has been observed on the Marvell Armada 38x serial port.
Writes to UART_LCR can result in characters that are currently held in the
TX FIFO being lost rather than sent, even if the userspace process has
attempted to flush them.
This is most visible when using the "resize" command (tested on Busybox),
where we have observed the escape code for restoring cursor position
becoming mangled.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_8250_throttle() is called when tty RX buffer is about to overflow
and can no longer keep up with the rate at which UART is receiving data.
So, the expectation of this callback, is that UART stops RX and asserts
HW flow control to signal the sender to stop sending more data.
omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer
serviced, leading to assertion of flow control once RX FIFO is full.
But, this does not work when DMA is enabled as driver keeps queuing new
RX DMA request in completion handler without brothering about throttling
request made by the higher layer.
This patch introduces a flag that can be used to determine whether or
not to queue next RX DMA request based on throttling request.
Without this patch, tty buffer overflows are reported at higher
baudrates.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar sleep wake-up handling has been done on a per-channel basis by
virtue of INT0 being accessible from each channel's address space. I
believe this was initially done out of necessity, but now that Exar
devices have their own driver, we can do things more efficiently by
registering a dedicated INT0 handler at the PCI device level.
I see this change providing the following benefits:
1. If more than one port is active, eliminates the redundant bus
cycles for reading INT0 on every interrupt.
2. This note associated with hooking in the per-channel handler in
8250_port.c is resolved:
/* Fixme: probably not the best place for this */
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit
de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")
obviously tries to cure symptoms, and not a root cause.
The root cause is the non-flexible rate calculation inside the
corresponding clock driver. What we need is to provide maximum UART
divisor value to the clock driver to allow it do the job transparently
to the caller.
Since from the initial commit message I have got no clue which clock
driver actually needs to be amended, I leave this exercise to the people
who know better the case.
Moreover, it seems [1] the fix introduced a regression. And possible
even one more [2].
Taking above, revert the commit de9e33bdfa for now.
[1]: https://www.spinics.net/lists/linux-serial/msg28872.html
[2]: https://github.com/Dunedan/mbp-2016-linux/issues/29#issuecomment-357583782
Fixes: de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Ed Blake <ed.blake@sondrel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the devicetree, it is possible to specify the baudrate, parity,
bits, flow of the early console, by passing a configuration string like
this:
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:57600n8";
};
This, for instance, will configure the early console for a baudrate of
57600 bps, no parity, and 8 bits per baud.
This patches implements parsing of this configuration string in the
8250_ingenic driver, which previously just ignored it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The JZ4770 SoC's UART is no different from the other JZ SoCs, so this
commit simply adds the ingenic,jz4770-uart compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error pointer from devm_reset_control_get_optional_shared() is
not propagated.
One of the most common problem scenarios is it returns -EPROBE_DEFER
when the reset controller has not probed yet. In this case, the
probe of the reset consumer should be deferred.
Fixes: e2860e1f62 ("serial: 8250_of: Add reset support")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the port register error
handling case instead of 0, as done elsewhere in this function.
Fixes: 39be40ce06 ("serial: 8250_uniphier: fix serial port index in private data")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed a spelling error in a comment.
Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is no clock rate for uartclk defined, disable the previously
enabled clock again.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 23f5b3fdd0 serial: 8250_dw: only get the clock rate in one place
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using "make kvmconfig" results in a potentially unusable linux image
on s390. The reason is that both the (default on s390) sclp consoles
as well as the 8250 console register a ttyS<x> as console. Since there
will be no 8250 on s390 let's fence 8250. This will ensure that there
is always a working sclp console.
Reported-by: Alice Frosi <alice@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If either uartclk or baud are 0, avoid calculating and setting a divisor
based on them since the output will almost certainly be garbage.
This also allows platforms such as the MIPS generic kernel, which has no
way to know a valid BASE_BASE for the board it is actually booted on at
compile time, to set BASE_BAUD to 0 and avoid early_8250 setting a bad
divisor.
This fixes a regression caused by commit 31cb9a8575 ("earlycon:
initialise baud field of earlycon device structure"), which changed the
behavior of of_setup_earlycon such that it sets a baud rate in the
earlycon structure where previously it was left as 0. All boards
supported by the MIPS generic kernel started outputting garbage from the
boot console due to an incorrect divisor being set.
Fixes: 31cb9a8575 ("earlycon: initialise baud field of earlycon device structure")
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).
[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat a
bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnD+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynAmgCfSSr/9qiCE0vfP5eVYjddzxfWyZ4AoMbKORZC
5x2KVW0Btrbs3WmnD7ZU
=PSea
-----END PGP SIGNATURE-----
Merge tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat
a bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
tty: ehv_bytechan: fix spelling mistake
tty: serial: meson: allow baud-rates lower than 9600
serial: 8250_fintek: Fix crash with baud rate B0
serial: 8250_fintek: Disable delays for ports != 0
serial: 8250_fintek: Return -EINVAL on invalid configuration
tty: Remove redundant license text
tty: serdev: Remove redundant license text
tty: hvc: Remove redundant license text
tty: serial: Remove redundant license text
tty: add SPDX identifiers to all remaining files in drivers/tty/
tty: serial: jsm: remove redundant pointer ts
tty: serial: jsm: add space before the open parenthesis '('
tty: serial: jsm: fix coding style
tty: serial: jsm: delete space between function name and '('
tty: serial: jsm: add blank line after declarations
tty: serial: jsm: change the type of local variable
tty: serial: imx: remove dead code imx_dma_rxint
tty: serial: imx: disable ageing timer interrupt if dma in use
serial: 8250: fix potential deadlock in rs485-mode
serial: m32r_sio: Drop redundant .data assignment
...
The 8250_fintek.c is support the Fintek F81866/F81216 with dynamic clock.
But It'll generate "division by zero" exception and crash in
fintek_8250_set_termios() with baud rate 0 on baudrate_table[i] % baud.
It can be tested with following C code:
...
struct termios options;
tcgetattr(fd, &options);
...
options.c_cflag = CS8 | CREAD; /* baud rate 0 */
tcsetattr(fd, TCSANOW, &options);
tcflush(fd, TCIOFLUSH);
Fixes: 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Reported-by: Lukas Redlinger <rel+kernel@agilox.net>
Cc: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet, only the first port supports delay before
send and delay after send.
Reported-by: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware does not support having the same RTS level during RX and TX
when RS485 mode is on (URA in Fintek terminology).
The manufacturer has also confirmed that the delays are not enabled if
the RS485 mode is not enabled.
Therefore we should return -EINVAL if the user wants to have the same
value for RTS_ON_SEND and RTS_AFTER_SEND.
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Canceling hrtimer when holding uart spinlock can deadlock.
CPU0: syscall write
-> get uart port spinlock
-> write uart
-> start_tx_rs485
-> hrtimer_cancel
-> wait for hrtimer callback to finish
CPU1: hrtimer IRQ
-> run hrtimer
-> em485_handle_stop_tx
-> get uart port spinlock
CPU0 is waiting for the hrtimer callback to finish, but the hrtimer
callback running on CPU1 is waiting to get the uart port spinlock.
This deadlock can be avoided by not canceling the hrtimers in these paths.
Setting active_timer=NULL can be done without accessing hrtimer,
and that will effectively cancel operations that would otherwise have been
performed by the hrtimer callback.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4d ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Sean Young <sean@mess.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().
Tested on iBASE MI802.
Cc: stable@vger.kernel.org
Tested-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Reviewd-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dw8250_set_termios sets the input clock to the nearest
achievable rate to baudx16. If necessary, the input clock is then
divided down to baudx16 using an integer divider within the UART
device, with the divisor calculated in the 8250 core driver.
However, the clock rate set by dw8250_set_termios and subsequently
divided down could be considerably different to the target baudx16
rate, resulting in incorrect operation. This patch fixes this by
iteratively searching for an input clock rate that is within +/-1.6%
of an integer multiple of the target baudx16 rate.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a define for the maximum baud rate divisor, to improve code
readability.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Cedar Fork PCH has similar HSU as has been used on Intel Denverton.
Add PCI ID to get it enumerated.
While here, remove DNV part form INTEL_MID_UART_DNV_FISR to show that is
used not only on Intel Denverton from now on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is fix the warning reported by smatch as following:
drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81216H had 4 clocksource 1.8432/18.432/14.769/24MHzand baud rates can
be up to 1.5Mbits with 24MHz. The register value and mask is the same with
F81866. But F81866 register address is F2h, F81216H is F0h.
We'll implements the dynamic clocksource in fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81866 had 4 clocksource 1.8432/18.432/14.769/24MHz and baud rates can
be up to 1.5Mbits with 24MHz. We'll implements the dynamic clocksource in
fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes, and
a new serial driver. Also in here are some much needed goldfish tty
driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa2A+A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylNKACfWOuWb4PEGzPg2hF57V1g0cq8VXEAn0BtZT+n
uuCBV53ylesoHhEhKf/D
=g+za
-----END PGP SIGNATURE-----
Merge tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes,
and a new serial driver. Also in here are some much needed goldfish
tty driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (94 commits)
tty: goldfish: Implement support for kernel 'earlycon' parameter
tty: goldfish: Use streaming DMA for r/w operations on Ranchu platforms
tty: goldfish: Refactor constants to better reflect their nature
serial: 8250_port: Remove useless NULL checks
earlycon: initialise baud field of earlycon device structure
tty: hvcs: make ktermios const
pty: show associative slave of ptmx in fdinfo
tty: n_gsm: Add compat_ioctl
tty: hvcs: constify vio_device_id
tty: hvc_vio: constify vio_device_id
tty: mips_ejtag_fdc: constify mips_cdmm_device_id
Introduce 8250_men_mcb
mcb: introduce mcb_get_resource()
serial: imx: Avoid post-PIO cleanup if TX DMA is started
tty: serial: imx: disable irq after suspend
serial: 8250_uniphier: add suspend/resume support
serial: 8250_uniphier: use CHAR register for canary to detect power-off
serial: 8250_uniphier: fix serial port index in private data
serial: 8250: of: Add new port type for MediaTek BTIF controller on MT7622/23 SoC
dt-bindings: serial: 8250: Add MediaTek BTIF controller bindings
...
After switching to HR timers for RS485 the NULL checks for the object
inside timer functions become useless.
Remove them to avoid confusion to static analyzers.
Fixes 6e0a5de213 ("serial: 8250: Use hrtimers for rs485 delays")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the 8250_men_mcb driver for the MEN 16Z125
IP-Core. This is a 16550-type UART with a 60 byte FIFO.
Due to strange old hardware, every board using this IP core requires
different values for uartclk. A reasonable default is included in
addition to the support of three boards. Additional values for other
boards will be added later.
This v2 has some whitespace fixes, I screwed this up yesterday.
Signed-off-by: Michael Moese <michael.moese@men.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add suspend/resume support for UniPhier serial driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 core uses the SCR as a canary to discover if the console has
been powered-off.
This hardware does not have SCR at offset 7, but an unused register
CHAR at a different offset. As long as the character interrupt is
disabled, the register access has no impact, so it is useful as an
alternative scratch register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port() may allocate a different port index
than requested. The driver needs to remember the returned value of
serial8250_register_8250_port() for later use. Otherwise, the .remove
hook may unregister a different port.
Fixes: 1a8d2903cb ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module called CONNSYS inside the SoC which could be mostly
found on those MediaTek SoCs with Bluetooth feature such as MT7622 and
MT7623 SoCs.
And the controller is made as being compatible with the 8250 register
layout with extra registers such as DMA enablement so it tends to be
integrated with reusing 8250 OF driver. However, DMA mode is not being
supported yet in the current driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parisc_device_id are not supposed to change at runtime. All functions
working with parisc_device_id provided by <asm/parisc-device.h> work
with const parisc_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
66AK2G UART instances are not apart of the ALWAYS_ON power domain.
Therefore, pm_runtime calls must be made to properly insure the appropriate
power domains needed by UART are on. Keep legacy clk api calls since other
users of this driver may not support PM runtime.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use slightly more compact of_property_read_bool() calls for the boolean
properties instead of of_find_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the timers where based on the classic timers, giving a too
coarse resolution on systems with configs of less than 1000 HZ.
This patch changes the rs485 timers to hrtimers.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two tty serial driver fixes for 4.13-rc5. One is a revert of a
-rc1 patch that turned out to not be a good idea, and the other is a fix
for the pl011 serial driver.
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+1vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykreACeLI2spfagnOcnW264PGHxLMgj47EAn0JPSNIg
5FLEtVsgxMuc8kc4LkDb
=58g+
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
This reverts commit 1104321a7b.
The code is not dead at all and breaks winbond-cir.
Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a CIR port
lirc lirc0: lirc_dev: driver ir-lirc-codec (winbond-cir) registered at minor = 0
winbond-cir 00:03: Region 0x2f8-0x2ff already in use!
winbond-cir: probe of 00:03 failed with error -16
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device-specific property should be prefixed with the vendor name,
not "linux,", as Linus Walleij pointed out. Change this and document the
bindings of this platform device.
We didn't ship the old binding in a release yet. So we can still change
it without breaking an official API.
Fixes: 380b1e2f3a ("gpio-exar/8250-exar: Make set of exported GPIOs configurable")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the board we are guessing has been listed in black list we don't need
to enable it twice. The associated driver, if any, will take care about
proper initialization.
To achieve this we split out two helper functions, i.e.
serial_pci_is_class_communication() and serial_pci_is_blacklisted() which will
be called before pcim_enable_device(). We can do this since PCI specification
requires class, device and vendor ID registers to be always present in the
configuration space.
As an example what happens before this patch applied
(These are some debug prints, don't search for them in kernel sources):
serial 0000:00:04.1: Mapped GSI28 to IRQ28
serial 0000:00:04.2: Mapped GSI29 to IRQ29
serial 0000:00:04.3: Mapped GSI54 to IRQ54
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54
After we will have just last three lines out of above.
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54
While here, correct a value of error code mentioned in the comment of
serial_pci_guess_board().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First 16 bits in the flags field are user-visible except
UPF_NO_TXEN_TEST. To keep it clean we introduce internal quirks and move
UPF_NO_TXEN_TEST to them. Rename the constant to UPQ_NO_TXEN_TEST to
distinguish with port flags. Users are converted accordingly.
The quirks field might be extended later to hold the additional ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several error handling paths in aspeed_vuart_probe(),
where sysfs group is left unremoved. The patch fixes them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_disable_unprepare(info->clk) is missed in of_platform_serial_probe(),
while irq_dispose_mapping(port->irq) is missed in of_platform_serial_setup().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
12626 18128 0 30754 7822 tty/serial/8250/8250_pci.o
File size After adding 'const':
text data bss dec hex filename
23986 6768 0 30754 7822 tty/serial/8250/8250_pci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4030 1280 0 5310 14be tty/serial/8250/8250_exar.o
File size After adding 'const':
text data bss dec hex filename
4958 352 0 5310 14be tty/serial/8250/8250_exar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO line
may loose its state during suspend/resume of the system to save
power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes.
-----BEGIN PGP SIGNATURE-----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=TpW1
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
This implements the setup of RS232 and the switch-over to RS485 or RS422
for the Siemens IOT2040. That uses an EXAR XR17V352 with external logic
to switch between the different modes. The external logic is controlled
via MPIO pins of the EXAR controller.
Only pin 10 can be exported as GPIO on the IOT2040. It is connected to
an LED.
As the XR17V352 used on the IOT2040 is not equipped with an external
EEPROM, it cannot present itself as IOT2040-variant via subvendor/
subdevice IDs. Thus, we have to check via DMI for the target platform.
Co-developed with Sascha Weisenberger.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the SIMATIC, IOT2040 only a single pin is exportable as GPIO, the
rest is required to operate the UART. To allow modeling this case,
expand the platform device data structure to specify a (consecutive) pin
subset for exporting by the gpio-exar driver.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This prepares the addition of IOT2040 platform support by preparing the
needed setup and rs485_config hooks.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the parent of the exar gpiochip to its platform device, like other
gpiochips are doing it. In order to keep the relationship discoverable
for ACPI systems, set the platform device companion to the PCI device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Commtech adapters need the MPIOs for internal purposes, and the
gpio-exar driver already refused to pick them up. But there is actually
no point in even creating the underlying platform device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA RX completion handler for UART is called from a tasklet and hence
may be delayed depending on the system load. In meanwhile, there may be
RX timeout interrupt which can get serviced first before DMA RX
completion handler is executed for the completed transfer.
omap_8250_rx_dma_flush() which is called on RX timeout interrupt makes
sure that the DMA RX buffer is pushed and then the FIFO is drained and
also queues a new DMA request. But, when DMA RX completion handler
executes, it will erroneously flush the currently queued DMA transfer
which sometimes results in data corruption and double queueing of DMA RX
requests.
Fix this by checking whether RX completion is for the currently queued
transfer or not. And also hold port lock when in DMA completion to avoid
race wrt RX timeout handler preempting it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BCM2835 MINI UART has non-standard THRE semantics. Conventionally
the bit means that the FIFO is empty (although there may still be a
byte in the transmit register), but on 2835 it indicates that the FIFO
is not full. This causes interrupts after every byte is transmitted,
with the FIFO providing some interrupt latency tolerance.
A consequence of this difference is that the usual strategy of writing
multiple bytes into the TX FIFO after checking THRE once is unsafe.
In the worst case of 7 bytes in the FIFO, writing 8 bytes loses all
but the first since by then the FIFO is full.
There is an HFIFO ("Hidden FIFO") capability that causes the transmit
loop to terminate when both THRE and TEMT are set, i.e. when the TX
block is completely idle. This is unnecessarily cautious, potentially
causing gaps in transmission.
Add a new conditional to the transmit loop, predicated on CAP_MINI,
that exits when THRE is no longer set (the FIFO is full). This allows
the FIFO to fill quickly but subsequent writes are paced by the
transmission rate.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes reloading of the GPIO driver for the same platform device
instance as created by the exar UART driver: First of all, the driver
sets drvdata to its own value during probing and does not restore the
original value on exit. But this won't help anyway as the core clears
drvdata after the driver left.
Set the platform device parent instead.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit e4fda3a042 ("serial: don't register CIR serial ports") adds a
check for PORT_8250_CIR to serial8250_register_8250_port(). But the code
isn't needed as the function never takes the branch when the port is CIR
serial port.
This patch deletes the dead code.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commtech adapters apparently need the original setting as outputs, see
https://marc.info/?l=linux-gpio&m=149557425201323&w=2. Account for that.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the hooks for an optional reset controller in the 8250 device
tree node.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AUX/mini-UART in the BCM2835 family of procesors is a cut-down
8250 clone. In particular it is lacking support for the following
features: CSTOPB PARENB PARODD CMSPAR CS5 CS6
Add a new capability (UART_CAP_MINI) that exposes the restrictions to
the user of the termios API by turning off the unsupported features in
the request.
N.B. It is almost possible to automatically discover the missing
features by reading back the LCR register, but the CSIZE bits don't
cooperate (contrary to the documentation, both bits are significant,
but CS5 and CS6 are mapped to CS7) and the code is much longer.
See: https://github.com/raspberrypi/linux/issues/1561
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After migrating 8250_exar to MSI in 172c33cb61, we can get stuck
without further interrupts because of the special wake-up event these
chips send. They are only cleared by reading INT0. As we fail to do so
during startup and shutdown, we can leave the interrupt line asserted,
which is fatal with edge-triggered MSIs.
Add the required reading of INT0 to startup and shutdown. Also account
for the fact that a pending wake-up interrupt means we have to return 1
from exar_handle_irq. Drop the unneeded reading of INT1..3 along with
this - those never reset anything.
An alternative approach would have been disabling the wake-up interrupt.
Unfortunately, this feature (REGB[17] = 1) is not available on the
XR17D15X.
Fixes: 172c33cb61 ("serial: exar: Enable MSI support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
modified the probing logic for PNP0501 devices, to remove a collision
between the generic 16550A driver and the Fintek driver, which reused
the same ACPI _HID.
The Fintek device probe is now incorporated into the common 8250 probe
path, and gets called for all discovered 16550A compatible devices,
including ones that are MMIO mapped rather than IO mapped. However,
the Fintek driver assumes the port base is a I/O address, and proceeds
to probe some arbitrary offsets above it.
This is generally a wrong thing to do, but on ARM systems (having no
native port I/O), this may result in faulting accesses of completely
unrelated MMIO regions in the PCI I/O space. Given that this is at
serial probe time, this results in hard to diagnose crashes at boot.
So let's restrict the Fintek probe to devices that we know are using
port I/O in the first place.
Fixes: fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the safe default for GPIOs with unknown external wiring.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds a driver for the 16550-based Aspeed virtual UART
device. We use a similar process to the of_serial driver for device
probe, but expose some VUART-specific functions through sysfs too.
The VUART is two UART 'front ends' connected by their FIFO (no actual
serial line in between). One is on the BMC side (management controller)
and one is on the host CPU side.
This driver is for the BMC side. The sysfs files allow the BMC
userspace, which owns the system configuration policy, to specify at
what IO port and interrupt number the host side will appear to the host
on the Host <-> BMC LPC bus. It could be different on a different system
(though most of them use 3f8/4).
OpenPOWER host firmware doesn't like it when the host-side of the
VUART's FIFO is not drained. This driver only disables host TX discard
mode when the port is in use. We set the VUART enabled bit when we bind
to the device, and clear it on unbind.
We don't want to do this on open/release, as the host may be using this
bit to configure serial output modes, which is independent of whether
the devices has been opened by BMC userspace.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probing of THRE irq behaviour assumes the other end will be reading
bytes out of the buffer in order to probe the port at driver init. In
some cases the other end cannot be relied upon to read these bytes, so
provide a flag for them to skip this step.
Bit 19 was chosen as the flags are a int and the top bits are taken.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UPF_EXAR_EFR is set globally for each port enumerated by the driver.
Thus, no need to repeat this in individual ->setup() hook.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel always writes log messages to console via
serial8250_console_write()->serial8250_console_putchar() which directly
accesses UART_TX register _without_ using DMA.
But, if other processes like systemd using same UART port, then these
writes are handled by a different code flow using 8250_omap driver where
there is provision to use DMA.
It seems that it is possible that both DMA and CPU might simultaneously
put data to UART FIFO and lead to potential loss of data due to FIFO
overflow and weird data corruption. This happens when both kernel
console and userspace tries to write simultaneously to the same UART
port. Therefore, disable DMA on kernel console port to avoid potential
race between CPU and DMA.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQIVAwUAWPiW6vSw1s6N8H32AQLOrw/+NTqGf7bjq+64YKS6NfR0XDgE+wNJltGO
ck7zJW3NHIg76RNu8s0I9xg5aVmwizz3Z5DGROZquaolnezux4tQihZ3AFyxIzLc
+Y3WHYagcML7yFfjl/WznCLRD5EW3yPln4lCvQO0nW/xICRYeRI057JaIbi2Dtek
BhcXt3c4AjXDLdYJkgtHV3p2R2mt8hcdFdWqqx6s7JaIThZNRGNzxAgtbcB9k5IW
HVG9ZEIL73VBYWHrYivzjHYF5rBnNCPt87eOwDQeTOSkhv8te+u9k+bH8vxZw1T0
XUtDrLBndKiuVo2GUfLkkF8LItx3Q9eLCJYy0joaIliyPqTEsPx9KjQ+Af0cxS9s
ZPCZ5SYf96stKmDeL5xaMfrAmeyVHJ4lc4JTOqdzbIT8blsOSfYO/03p0ALShSDv
/RQLaKGlf8Bjoy8PwKFcXb4sIDufcd/U1Av/EMFXxOfgN/u2JUkGKq6EaIM5B68L
fHPje+aR9VNELPmPjwNOWtmN4I79EH3EItQf7zv0KG+UeKhcHLx/EAcSJ3ZRKEkH
Lathg7pPOEJGArPiVO79TZzBG01ADn1aiwv65XObMzNZ+54xI/mN/Y1DNF/kL5jU
XzvNzEjFt8mwMIZGVNdAt4+pDyMfIZGZSyUkSRKFnaQZMIvQrfQIU9RLBYLX5eOx
+/p0VkIwDpg=
=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/tty/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jiri Slaby <jslaby@suse.com>
cc: linux-serial@vger.kernel.org
Define an OF early console for Palmchip UART, which can be enabled
by passing "earlycon" on the boot command line.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit d0aeaa83f0 ("serial: exar:
split out the exar code from 8250_pci") the exar driver got its own
Kconfig. However the text for the new option was never changed from
the original 8250_PCI text, and hence it appears confusing when you
get asked the same question twice:
8250/16550 PCI device support (SERIAL_8250_PCI) [Y/n/m/?] (NEW)
8250/16550 PCI device support (SERIAL_8250_EXAR) [Y/n/m] (NEW)
Adding to the confusion, is that there is no help text for this new
option to indicate it is specific to a certain family of cards.
Fix both issues at the same time, as well as the space vs. tab issues
introduced in the same commit.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using dev_name() as IRQ name during request_irq() might be misleading in
case of serial over PCI. Therefore identify serial port IRQ using
uart_port's name field. This will help mapping IRQs to appropriate
ttySN(where N is the serial port index) instances.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MSI needs it as well.
Should have no practical impact, though, as DMA is always available on
the Quark. But given the few users of pci_alloc_irq_vectors so far, this
incorrect pattern may spread otherwise.
Fixes: 3f3a46951e ("serial: 8250_lpss: set PCI master only for private DMA")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81866 supports baud rates higher than 115200 but needs to raise
it's clock speed from 1.84 to 14.76 MHz.
This is eight times faster, so gives 921600 as resulting baud_base.
F81866 clock register 0xf2:
Bit 7-2 reserved
Bit 1-0 00: 1.8432MHz
01: 18.432MHz
10: 24MHz
11: 14.769MHz
Signed-off-by: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing "serial" as name during request_irq() results in all serial port
irqs have same name. This does not help much to easily identify which
irq belongs to which serial port instance. Therefore pass dev_name()
during request_irq() so that better identifiable name is listed for
serial ports in cat /proc/interrupts output.
Output of cat /proc/interrupts
Before this patch:
26: 689 0 GICv2 309 Edge serial
After this patch:
26: 696 0 GICv2 309 Edge 2530c00.serial
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be
used") recently broke the 8250_dw driver on platforms which don't select
HAVE_CLK, as dw8250_set_termios() gets confused by the behaviour of the
fallback HAVE_CLK=n clock API in linux/clk.h which pretends everything
is fine but returns (valid) NULL clocks and 0 HZ clock rates.
That 0 rate is written into the uartclk resulting in a crash at boot,
e.g. on Cavium Octeon III based UTM-8 we get something like this:
1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 41, base_baud = 25000000) is a OCTEON
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1 at drivers/tty/serial/serial_core.c:441 uart_get_baud_rate+0xfc/0x1f0
...
Call Trace:
...
[<ffffffff8149c2e4>] uart_get_baud_rate+0xfc/0x1f0
[<ffffffff814a5098>] serial8250_do_set_termios+0xb0/0x440
[<ffffffff8149c710>] uart_set_options+0xe8/0x190
[<ffffffff814a6cdc>] serial8250_console_setup+0x84/0x158
[<ffffffff814a11ec>] univ8250_console_setup+0x54/0x70
[<ffffffff811901a0>] register_console+0x1c8/0x418
[<ffffffff8149f004>] uart_add_one_port+0x434/0x4b0
[<ffffffff814a1af8>] serial8250_register_8250_port+0x2d8/0x440
[<ffffffff814aa620>] dw8250_probe+0x388/0x5e8
...
The clock API is defined such that NULL is a valid clock handle so it
wouldn't be right to check explicitly for NULL. Instead treat a
clk_round_rate() return value of 0 as an error which prevents uartclk
being overwritten.
Fixes: 6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-serial@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: bcm-kernel-feedback-list@broadcom.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jason Uy <jason.uy@broadcom.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_round_rate returns a signed long and may possibly return errors
in it, for example if there is no possible rate.
Till now dw8250_set_termios ignored any error, the signednes and would
just use the value as input to clk_set_rate. This of course falls apart
if there is an actual error, so check for errors and only try to set
a rate if the value is actually valid.
This turned up on some Rockchip platforms after commit
6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
enabled set_termios callback in all cases, not only ACPI.
Fixes: 6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pci_alloc_irq_vectors to enable MSI when available. At least the
XR17V352 supports this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these registers is relevant for the userspace API.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Became obsolete with the split-out of 8250_exar.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those are Exar-based, too.
With the required refactoring of the code to fit into 8250_exar, we
automatically fix the same issue pci_xr17v35x_setup had before: 8XMODE,
FCTL, TXTRG and RXTRG were always only set for port 0. Now they are
initialized for the correct target port by using port.membase.
Now we can also cleanly fix the blacklist of 8250_pci so that all
Commtech devices are rejected and 8250_exar can handle them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far, pci_xr17v35x_setup always initialized 8XMODE, FCTR & Co. for
port 0 because it used the address of that port instead of moving the
pointer according to the port number. Fix this and remove the unneeded
temporary ioremap by moving default_setup up and reusing the membase it
fills into the port structure.
Fixes: 14faa8cce8 ("tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcim_iomap_table only returns the table of mapping, it does not perform
them. For that, we need to call pcim_iomap, but only if that mapping was
not done before.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a Rockchip rk3399-based board during suspend/resume testing, we
found that we could get the console UART into a state where it would
print this to the console a lot:
serial8250: too much work for irq42
Followed eventually by:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 11s!
Upon debugging I found that we're in this state:
iir = 0x000000cc
lsr = 0x00000060
It appears that somehow we have a RX Timeout interrupt but there is no
actual data present to receive. When we're in this state the UART
driver claims that it handled the interrupt but it actually doesn't
really do anything. This means that we keep getting the interrupt
over and over again.
Normally we don't actually need to do anything special to handle a RX
Timeout interrupt. We'll notice that there is some data ready and
we'll read it, which will end up clearing the RX Timeout. In this
case we have a problem specifically because we got the RX TImeout
without any data. Reading a bogus byte is confirmed to get us out of
this state.
It's unclear how exactly the UART got into this state, but it is known
that the UART lines are essentially undriven and unpowered during
suspend, so possibly during resume some garbage / half transmitted
bits are seen on the line and put the UART into this state.
The UART on the rk3399 is a DesignWare based 8250 UART. From mailing
list posts, it appears that other people have run into similar
problems with DesignWare based IP. Presumably this problem is unique
to that IP, so I have placed the workaround there to avoid possibly of
accidentally triggering bad behavior on other IP. Also note the RX
Timeout behaves very differently in the DMA case, for for now the
workaround is only applied to the non-DMA case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/tty/serial/8250/8250_pci.c:3916:6: warning:
symbol 'pciserial_detach_ports' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively. The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954. The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the Exar specific codes from 8250_pci and blacklist those chips
so that the new Exar serial driver binds to the devices.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the serial driver for the Exar chips. And also register the
platform device for the GPIO provided by the Exar chips.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During build testing, I ran into a warning in a driver that I
had written myself at some point:
drivers/tty/serial/8250/8250_of.c: In function 'of_platform_serial_probe':
drivers/tty/serial/8250/8250_of.c:233:1: error: the frame size of 1200 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
This is harmless by itself, but it shows two other problems in
the driver:
- It still tries to be generic enough to handle all kinds of serial
ports, where in reality the driver has been 8250-only for a while,
and every other uart has its own DT support
- As a result of that generalization, we keep two copies of
'struct uart_port' on the stack during probe(). This is completely
unnessary.
Removing the last code dealing with unsupported port_type values
solves both problems nicely, and reduces the stack size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:
omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?
Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this warning is triggered for allmodconfig on m68k. It is
well intentioned, in that if you are building the driver but not
enabling one of the platforms where the hardware exists, you get a
warning.
The warning dates back to pre-git days, and now we have COMPILE_TEST
so we can use that to mask the warning for people who are obviously
just doing build coverage on tree wide changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 UART DMA support was marked broken by default as it was not
possible to pause ongoing RX DMA transfer. Now that both SDMA and
EDMA can support pause operation for RX DMA transactions, don't set
rx_dma_broken to true by default. With this patch 8250_omap driver will
use DMA by default.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that DMA transfer is already complete but, completion
handler is yet to be called, when dmaengine_pause() is called in case of
error condition(like break/rx timeout). This leads to dmaengine_pause()
API to return EINVAL (as descriptor is already NULL) causing
rx_dma_broken flag to be set and effectively disabling RX DMA.
Fix this by calling dmaengine_pause() only when transfer is in progress.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here, If ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to set PCI bus mastering when device is not doing any DMA. It
includes MSI type of interrupts. Currently only UART on Denverton, which is DMA
capable, might have MSI enabled.
Taking above into account enable bus mastering for Denverton case only.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable MSI type of interrupt if PCI BIOS supports it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Tangier B0 and continuing on Anniedale the HSU DMA interrupt
line is actually shared with UART. Handling them independently is racy and
quite often comes with the following traceback.
irq 54: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6-edison64-86244934+ #1
Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
ffff88003f203eb0 ffffffff8130e718 ffff880032627000 ffff88003262709c
ffff88003f203ed8 ffffffff810a3960 ffff880032627000 0000000000000000
ffff880032627000 ffff88003f203f10 ffffffff810a3cc7 ffff880032627000
Call Trace:
<IRQ>
[<ffffffff8130e718>] dump_stack+0x4d/0x65
[<ffffffff810a3960>] __report_bad_irq+0x30/0xc0
[<ffffffff810a3cc7>] note_interrupt+0x227/0x270
[<ffffffff810a1380>] handle_irq_event_percpu+0x40/0x50
[<ffffffff810a13b7>] handle_irq_event+0x27/0x50
[<ffffffff810a42d5>] handle_fasteoi_irq+0x85/0x150
[<ffffffff8101d7fe>] handle_irq+0x6e/0x120
[<ffffffff8105b8bc>] ? _local_bh_enable+0x1c/0x50
[<ffffffff8101d0d6>] do_IRQ+0x46/0xd0
[<ffffffff818cef3f>] common_interrupt+0x7f/0x7f
<EOI>
[<ffffffff818cdead>] ? mwait_idle+0x7d/0x140
[<ffffffff81024c9a>] arch_cpu_idle+0xa/0x10
[<ffffffff818ce150>] default_idle_call+0x20/0x30
[<ffffffff810908fd>] cpu_startup_entry+0x16d/0x1d0
[<ffffffff818c882d>] rest_init+0x6d/0x70
[<ffffffff81f93e8f>] start_kernel+0x3e2/0x3ef
[<ffffffff81f9343d>] x86_64_start_reservations+0x38/0x3a
[<ffffffff81f93529>] x86_64_start_kernel+0xea/0xed
handlers:
[<ffffffff81411670>] serial8250_interrupt
Disabling IRQ #54
Fix this by handling interrupt only in one place.
The issue is discussed here: https://github.com/andy-shev/linux/issues/5
Moreover this also fixes another bug when Rx DMA returns wrong residue and we
can't rely on it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the most common use case, the Synopsys DW UART driver does not
set the set_termios callback function. This prevents UPSTAT_AUTOCTS
from being set when the UART flag CRTSCTS is set. As a result, the
driver will use software flow control as opposed to hardware flow
control.
To fix the problem, the set_termios callback function is set to the
DW specific function. The logic to set UPSTAT_AUTOCTS is moved so
that any clock error will not affect setting the hardware flow
control.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Jason Uy <jason.uy@broadcom.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a new UART port type for TI DA8xx/OMAPL13x/AM17xx/AM18xx/66AK2x.
These SoCs have standard 8250 registers plus some extra non-standard
registers.
The UART will not function unless the non-standard Power and Emulation
Management Register (PWREMU_MGMT) is configured correctly. This is
currently handled in arch/arm/mach-davinci/serial.c for non-device-tree
boards. Making this part of the UART driver will allow UART to work on
device-tree boards as well and the mach code can eventually be removed.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding tristate options with "if EXPERT" is usually not a good idea.
You can decide that the driver should be included by default, but you
don't know if the user wants it built-in or as a module. Hiding the
option prevents the user from making that decision.
This is even more problematic when said option selects other options.
You end up with several device drivers forcibly built into the kernel.
In this specific case, drivers 8250_mid, virt-dma, hsu_dma and
hsu_dma_pci end up being built-in as soon as SERIAL_8250=y. It is
very common for distribution kernels to build the subsystem core code
into the kernel, because almost everybody will need it, but build all
the device drivers as modules. This should be made possible.
So drop the "if EXPERT" and make SERIAL_8250_MID visible.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 1fc969c759 ("serial: 8250_mid: make module available only on X86")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding tristate options with "if EXPERT" is usually not a good idea.
You can decide that the driver should be included by default, but you
don't know if the user wants it built-in or as a module. Hiding the
option prevents the user from making that decision.
This is even more problematic when said option selects other options.
You end up with several device drivers forcibly built into the kernel.
In this specific case, drivers 8250_lpss, dw_dmac_core and
dw_dmac_pci end up being built-in as soon as SERIAL_8250=y. It is
very common for distribution kernels to build the subsystem core code
into the kernel, because almost everybody will need it, but build all
the device drivers as modules. This should be made possible.
So drop the "if EXPERT" and make SERIAL_8250_LPSS visible.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a13e19cf3d ("serial: 8250_lpss: split LPSS driver to separate module")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding tristate options with "if EXPERT" is usually not a good idea.
You can decide that the driver should be included by default, but you
don't know if the user wants it built-in or as a module. Hiding the
option prevents the user from making that decision.
In this specific case, driver 8250_pci ends up being built-in as soon
as SERIAL_8250=y. It is very common for distribution kernels to build
the subsystem core code into the kernel, because almost everybody
will need it, but build all the device drivers as modules. This
should be made possible.
So drop the "if EXPERT" and make SERIAL_8250_PCI visible.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_DYNAMIC_DEBUG if dyndbg enables debug output in
8250_port.c deadlock happens inevitably on UART IRQ handling.
That's the problematic execution path:
---------------------------->8------------------------
UART IRQ:
serial8250_interrupt() ->
serial8250_handle_irq(): lock "port->lock" ->
pr_debug() ->
serial8250_console_write(): bump in locked "port->lock".
OR (if above pr_debug() gets removed):
serial8250_tx_chars() ->
pr_debug() ->
serial8250_console_write(): bump in locked "port->lock".
---------------------------->8------------------------
So let's get rid of those not that much useful debug entries.
Discussed problem could be easily reproduced with QEMU for x86_64.
As well as this fix could be mimicked with muting of dynamic debug for
the problematic lines as simple as:
---------------------------->8------------------------
dyndbg="+p; file 8250_port.c line 1756 -p; file 8250_port.c line 1822 -p"
---------------------------->8------------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Phillip Raffeck <phillip.raffeck@fau.de>
Cc: Anton Wuerfel <anton.wuerfel@fau.de>
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Thor Thayer <tthayer@opensource.altera.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a follow up to the commit a9b01b5823 ("serial: 8250_mid fix calltrace
when hotplug 8250 serial controller") in which the kernel crash was described
for another 8250 based driver. It appears that we have the very same issue in
8250_lpss. Fix it by unregistering serial driver first.
Cc: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When struct moxa8250_board is allocated, then num_ports should
be initialized in order to use it later in moxa8250_remove.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add resource type check for Fintek F81504/508/512, BAR3/4/5 must be
IORESOURCE_IO.
Fintek is trying to make F81504/508/512 works on MMIO interface, but
it's still in progress. We found some issue when the experiment IC
when the BAR3/4/5 is IORESOURCE_MEM. It'll cause wrong operation with
IO resource. So we'll add the resource check for this.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit needs to be reverted because it prevents people from
using the serial console as a secondary console with input being
directed to tty0.
IOW, if you boot with console=ttyS0 console=tty0 then all kernels
prior to this commit will produce output on both ttyS0 and tty0
but input will only be taken from tty0. With this patch the serial
console will always be the primary console instead of tty0,
potentially preventing people from getting into their machines in
emergency situations.
Fixes: d03516df83 ("tty: serial: 8250: add CON_CONSDEV to flags")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in RS485 emulation mode, __do_stop_tx_rs485() calls
serial8250_clear_fifos(). This not only clears the FIFOs, but also sets
all bits in their control register (UART_FCR) to 0.
One of the effects of this is the disabling of the FIFOs, which turns
them into single-byte holding registers. The rest of the driver doesn't
know this, which results in the lions share of characters passed into a
write call to be dropped.
(I can supply logic analyzer screenshots if necessary)
This fix replaces the serial8250_clear_fifos() call to
serial8250_clear_and_reinit_fifos() - this prevents the "dropped
characters" issue from manifesting again while retaining the requirement
of clearing the RX FIFO after transmission if the SER_RS485_RX_DURING_TX
flag is disabled.
Signed-off-by: Daniel Jedrychowski <avistel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fairly routine update this time around with all changes specific to drivers.
o New driver for STMicroelectronics FDMA
o Memory-to-memory transfers on dw dmac
o Support for slave maps on pl08x devices
o Bunch of driver fixes to use dma_pool_zalloc
o Bunch of compile and warning fixes spread across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pf0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
Fix the following Calltrace:
[ 77.768221] WARNING: CPU: 5 PID: 645 at drivers/dma/dmaengine.c:1069 dma_async_device_unregister+0xe2/0xf0
[ 77.775058] dma_async_device_unregister called while 1 clients hold a reference
[ 77.825048] CPU: 5 PID: 645 Comm: sh Not tainted 4.8.8-WR9.0.0.0_standard+ #3
[ 77.832550] Hardware name: Intel Corp. Aspen Cove/Server, BIOS HAVLCRB1.X64.0012.D58.1604140405 04/14/2016
[ 77.840396] 0000000000000000 ffffc90008adbc80 ffffffff81403456 ffffc90008adbcd0
[ 77.848245] 0000000000000000 ffffc90008adbcc0 ffffffff8105e2e1 0000042d08adbf20
[ 77.855934] ffff88046a861c18 ffff88046a85c420 ffffffff820d4200 ffff88046ae92318
[ 77.863601] Call Trace:
[ 77.871113] [<ffffffff81403456>] dump_stack+0x4f/0x69
[ 77.878655] [<ffffffff8105e2e1>] __warn+0xd1/0xf0
[ 77.886102] [<ffffffff8105e34f>] warn_slowpath_fmt+0x4f/0x60
[ 77.893508] [<ffffffff814187a9>] ? find_next_bit+0x19/0x20
[ 77.900730] [<ffffffff814bf83e>] ? dma_channel_rebalance+0x23e/0x270
[ 77.907814] [<ffffffff814bfee2>] dma_async_device_unregister+0xe2/0xf0
[ 77.914992] [<ffffffff814c53aa>] hsu_dma_remove+0x1a/0x60
[ 77.921977] [<ffffffff814ee14c>] dnv_exit+0x1c/0x20
[ 77.928752] [<ffffffff814edff6>] mid8250_remove+0x26/0x40
[ 77.935607] [<ffffffff8144f1b9>] pci_device_remove+0x39/0xc0
[ 77.942292] [<ffffffff8160cfea>] __device_release_driver+0x9a/0x140
[ 77.948836] [<ffffffff8160d0b3>] device_release_driver+0x23/0x30
[ 77.955364] [<ffffffff81447dcc>] pci_stop_bus_device+0x8c/0xa0
[ 77.961769] [<ffffffff81447f0a>] pci_stop_and_remove_bus_device_locked+0x1a/0x30
[ 77.968113] [<ffffffff81450d4e>] remove_store+0x5e/0x70
[ 77.974267] [<ffffffff81607ed8>] dev_attr_store+0x18/0x30
[ 77.980243] [<ffffffff8123006a>] sysfs_kf_write+0x3a/0x50
[ 77.986180] [<ffffffff8122f5ab>] kernfs_fop_write+0x10b/0x190
[ 77.992118] [<ffffffff811bf1c8>] __vfs_write+0x18/0x40
[ 77.998032] [<ffffffff811bfdee>] vfs_write+0xae/0x190
[ 78.003747] [<ffffffff811c1016>] SyS_write+0x46/0xb0
[ 78.009234] [<ffffffff81a4c31b>] entry_SYSCALL_64_fastpath+0x13/0x8f
[ 78.014809] ---[ end trace 0c36dd73b7408eb2 ]---
This happens when the 8250 serial controller is hotplugged as follows:
echo 1 > /sys/bus/pci/devices/0000:00:1a.0/remove
This trace happens due to the serial port still holding a reference when
the dma device is unregistered.
The dma unregister routine will check if there is still a reference exist,
if so it will give the WARNING(here serial port still was not unregister).
To fix this, We need to unregister the serial port first, then do DMA
device unregister to make sure there is no reference when to DMA routine.
Signed-off-by: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed. Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device. Those end up
racing with the EEH recovery, crashing it. Similar races were also
observed when opening the device and when shutting it down during
recovery.
This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards. Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery. This is similar to the solution used by the JSM serial
driver.
I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a set_ldisc function to enable/disable IrDA SIR mode according to
the new line discipline, if IrDA SIR mode is supported by the hardware
configuration.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose set_ldisc() function so that it can be overridden with a
platform specific implementation.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an IrDA UART capability flag and change the type of
uart_8250_port.capabilities to be u32 rather than unsigned short to
accommodate the additional flag.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When any 8250 based driver sets up DMA and has UART_CAP_RPM capability enabled
the device is left powered on after transfer is done. We need to schedule a
device suspend operation when DMA completes the transfer.
The patch is based on the work done by the reporter.
Reported-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following fix of runtime PM use in DMA mode requires at least
serial8250_rpm_put_tx() to be available. Export both calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fresh new serial driver for pxa produces warnings when
CONFIG_PM_SLEEP is disabled:
drivers/tty/serial/8250/8250_pxa.c:50:12: error: 'serial_pxa_resume' defined but not used [-Werror=unused-function]
drivers/tty/serial/8250/8250_pxa.c:41:12: error: 'serial_pxa_suspend' defined but not used [-Werror=unused-function]
This removes the #ifdef around the two functions and instead marks both
as __maybe_unused, which is more robust and avoids the warning.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
below patch to fix Fourth port offset of Percom PI7C9X7954 boards.
I had a problem using Fourth port on a pci express serial board based on Pericom
PI7C9X7954. Reading datasheet I notice a "special" offset assign to this port
when used in I/O mode.
Offset 0x0 -> UART 0
Offset 0x8 -> UART 1
Offset 0x10 -> UART 2
Offset 0x38 -> UART 3 <<---- This don't follow a logical sequence
This patch add a different init to last port, to have right offset.
I check also Pericom 7952 and 7958 but that devices follow logical sequence,
so they are ok.
Regards,
Angelo
Signed-off-by: Angelo Butti <buttiangelo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added pxa glue driver for 8250 supports console output, but
fails to build if the 8250 console is disabled:
drivers/tty/serial/8250/8250_pxa.o: In function `early_serial_pxa_setup':
8250_pxa.c:(.init.text+0x50): undefined reference to `early_serial8250_setup'
This adds an #ifdef like the other glue drivers have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware book says, the FCR is combined with a register called
CHAR (it will trigger interrupt when a specific character is
received). At first, I used lock/read/modify/write/unlock dance for
the FCR to not affect the upper bits, but the CHAR is actually never
used. It should not hurt to always clear the CHAR and to handle the
FCR as a normal case. It can save the costly locking.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For this driver, uart_port::regshift is always 2. Hardcode the
shift value instead of reading ->regshift to get an already known
value. (pointed out by Denys Vlasenko)
Furthermore, I am using register macros that are already shifted,
which will save code a bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NXP SC16C2552 requires that we always write a reset to the RX FIFO and
TX FIFO whenever we enable the FIFOs
Cc: xe-kernel@external.cisco.com
Signed-off-by: Steve Shih <sshih@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81865 is a LPC to 6 UARTs SuperIO. It has less functional UARTs
likes F81866. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81865 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
Level/Low: IRQ_MODE0:0
Edge/High: IRQ_MODE0:1
The following list is brief descriptions of F81865:
F81865 (0704)
9Bit(not implements with mainline)
RS485(implemented)
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81866 is a LPC to 6 UARTs SuperIO. It has fully functional UARTs
likes F81216H. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81866 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
The following list is brief descriptions of F81866:
F81866 (1010)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81216 is a LPC to 4 UARTs device. It's the F81216 series but
support less functional than F81216AD/F81216H
The following list is brief descriptions of F81216 series:
F81216H (0105)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
F81216AD (0216)
9Bit(not implements with mainline)
RS485(implemented)
F81216 (0208)
basically 16550A
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fintek F81216H had maximum 128Bytes FIFO, but some BIOS configurated
as normal 16Bytes FIFO. This patch will set 128Bytes FIFO and trigger
level multiplier as 4x when F81216H detected.
Default 16550A trigger level is 8Bytes. When this patch applied, the
trigger level will change to 8Byte x 4 = 32Byte. It can be reduce the RX
incoming interrupts.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set IRQ Mode when port probed in probe_setup_port()
It should hold the IO port premission via fintek_8250_enter_key() and
release via fintek_8250_exit_key() when we configure the SuperIO.
This patch will move all SuperIO configure operations to
probe_setup_port() to reduce fintek_8250_enter_key() and
fintek_8250_exit_key() usage.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we need to access SuperIO registers, It should write register offset
to base_addr and read/write value to base_addr + 1 to perform read/write.
We can make it more simply with write/read functions.
This patch add sio_read_reg()/sio_write_reg()/sio_write_mask_reg() to
reduce SuperIO register operation with lot of outb()/inb().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transfer the device-tree pxa uart handling from 8250_of to the new
8250_pxa. As a corollary, add the early console definition into
8250_pxa.
This enables to have the same uart node for the early console and the
normal uart.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of a direct assignment use pci_irq_vector() call as it's done for the
other case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable MWI mechanism if PCI bus master supports it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to set PCI bus mastering when device is not doing any DMA.
Though on Intel Quark DMA is a part of UART IP and thus shares same device in
Linux kernel.
Enable bus mastering only for Quark case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4fe0d15488 ("PCI: Use positive flags in pci_alloc_irq_vectors()")
replaces flags from negative to positive values which makes mandatory to have
the last argument in pci_alloc_irq_vectors() non-zero (if we want to be no-op).
This basically drops MSI enabling in 8250_lpss driver.
Restore desired behaviour in 8250_lpss by passing PCI_IRQ_ALL_TYPES instead of
0 to pci_alloc_irq_vectors().
Fixes: 60a9244a5d ("serial: 8250_lpss: enable MSI for Intel Quark")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pxa2xx-uart was a separate uart platform driver. It was declaring
the same device names and numbers as 8250 driver. As a result,
it was impossible to use 8250 driver on PXA SoCs.
Upon closer examination pxa2xx-uart turned out to be a clone of
8250_core driver.
Workaround for Erratum #19 according to Marvel(R) PXA270M Processor
Specification Update (April 19, 2010) is dropped. 8250_core reads
from FIFO immediately after checking DR bit in LSR.
The patch leaves the original SERIAL_PXA driver around. The original
driver is just marked DEPRECATED in Kconfig and C source. When
the original driver is considered safe to remove, no changes
to SERIAL_8250 will be necessary.
Compiling SERIAL_8250_CONSOLE and SERIAL_PXA_CONSOLE even without
SERIAL_8250_PXA breaks console for SERIAL_PXA. For this reasons, the new
and the original drivers are made mutually exclusive.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC: James Cameron <quozl@laptop.org>
CC: Robert Jarzmik <robert.jarzmik@free.fr>
CC: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[rebased on v4.8]
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this point, 'value' is always a byte, then this code is clearing
bit 15, which is already clear. I meant to clear bit 7.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big TTY and Serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by some
serial drivers, and they were all acked by the DMA maintainer. Also in
here is the long-suffering ACPI SPCR patchset, which was passed around
from maintainer to maintainer like a hot-potato. Seems I was the
sucker^Wlucky one. All of those patches have been acked by the various
subsystem maintainers as well.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNjEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwIcAn2uN
qCD8xQJ0Cs61hD1nUzhNygG8AJ94I4zz/fPGpyh/CtJfLQwtUdLhNA==
=Rken
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
The Altera 16550 soft IP UART requires 2 additional registers for
TX FIFO threshold support. These 2 registers enable the TX FIFO
Low Watermark and set the TX FIFO Low Watermark.
Set the TX FIFO threshold to the FIFO size - tx_loadsz.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize the tx_loadsz parameter from passed in devicetree
tx-threshold parameter.
The tx_loadsz is calculated as the number of bytes to fill FIFO
when tx-threshold is triggered.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Less magic that only requires comments.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have nice macro IRQ_RETVAL() we would use it to convert a flag of
handled interrupt from int to irqreturn_t.
The rationale of doing this is:
a) hence we implicitly mark hsu_dma_do_irq() as an auxiliary function that
can't be used as interrupt handler directly, and
b) to be in align with serial driver which is using serial8250_handle_irq()
that returns plain int by design.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon implementation used "unsigned long" internally, but there are systems
(ARM with LPAE) where sizeof(unsigned long) == 4 and uart is mapped beyond 4GiB
address range.
Switch to resource_size_t internally and replace obsoleted simple_strtoul() with
kstrtoull().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI identifier for UART on Hisilicon Hip05 SoC, be careful that
it is not 16550 compatible, and "reg-io-width" and "reg-shift" need
be set properly by _DSD method in DSDT.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the check of em485 variable to be either (em485) or (!em485) instead of
the explicit comparison to NULL.
While here, remove redundant check in __do_stop_tx_rs485() and
__stop_tx_rs485() since the functions ain't called with NULL value of em485
variable.
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are calls to serial8250_rpm_{get|put}() in __do_stop_tx_rs485() that are
certainly placed in a wrong location. I dunno how it had been tested with
runtime PM enabled because it is obvious "sleep in atomic context" error.
Besides that serial8250_rpm_get() is called immediately after an IO just
happened. It implies that the device is already powered on, see implementation
of serial8250_em485_rts_after_send() and serial8250_clear_fifos() for the
details.
There is no bug have been seen due to, as I can guess, use of auto suspend mode
when scheduled transaction to suspend is invoked quite lately than it's needed
for a few writes to the port. It might be possible to trigger a warning if
stop_tx_timer fires when device is suspended.
Refactor the code to use runtime PM only in case of timer function.
Fixes: 0c66940d58 ("tty/serial/8250: fix RS485 half-duplex RX")
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use an unified new dev variable instead of &pdev->dev and p->dev
in probe function.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The APM X-Gene SoC UART is the only board that still needs
the hard-coded values, so handle it separately in
dw8250_quirks(). The other ACPI platforms are able to
provide the values with device properties.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA on Intel Quark SoC is a part of UART IP block. Enable it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoCs, such as Intel Braswell, have DesignWare UART IP. Split out the
support of such chips to a separate module which also will be used for Intel
Quark later.
The rationale to have the separate driver to be existing:
- Do not contaminate 8250_pci.c anymore with LPSS related quirks
- All of them are using same DMA engine and they are Designware IP which means
that in the future we might share the code between 8250_dw.c and 8250_lpss.c
- It reduces the kernel memory footprint on non-X86 machines where 8250_pci.c
is in use
Besides the split the driver also has been refactored, in particular a) the DMA
and port setup are separate functions, b) the two new structures lpss8250 and
lpss8250_board are introduced to keep necessary data instead of
pciserial_board, c) DMA parameters are passed to the DMA setup via mentioned
custom structure. Most of the changes are done due to the future support of
UART DMA on Intel Quark.
The Intel Quark UART DMA support is based on bits taking from BSP code
published by Intel earlier.
The driver does not use any specific power management. PCI core takes care of
the default behaviour during suspend and resume.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Quark has 16550A compatible UART with autoflow feature enabled. It has
only 16 bytes of FIFO. Currently serial8250_do_set_termios() prevents to enable
autoflow since the minimum requirement of 32 bytes of FIFO size.
Drop a FIFO size limitation to allow autoflow control be enabled on such UARTs.
While here, comment out UART_CAP_AFE for PORT_AR7 since it wasn't working and
it will be not a good idea to use it in conjunction with trigger level of 1
byte.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UARTs, e.g. one is used in Intel Quark, have a different address base for
DMA operations. Introduce an additional field (per RX and TX DMA channels) in
struct uart_8250_dma to cover those cases.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mediatek can support baud rate up to 4M.
the 'uart_get_baud_rate' function will limit the max baud rate.
Modify max baud to remove the limit.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit c1a67b48f6 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com>
Fixes: c1a67b48f6 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should check the data->pclk, not data->clk when get apb_pclk.
Fixes: c8ed99d4f6a8("serial: 8250_dw: Add support for deferred probing")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial console is broken in v4.8-rcX. Mika and I independently bisected down to
commit 4ef03d3287 ("tty/serial/8250: use mctrl_gpio helpers").
Since neither author nor anyone else didn't propose a solution we better revert
it for now.
This reverts commit 4ef03d3287.
Link: https://lkml.kernel.org/r/20160809130229.GN1729@lahna.fi.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix for the fintek driver required defining some macros, but
one of them clashes with a system header on ARM:
drivers/tty/serial/8250/8250_fintek.c:34:0: error: "IRQ_MODE" redefined [-Werror]
#define IRQ_MODE 0x70
In file included from /git/arm-soc/arch/arm/include/asm/ptrace.h:13:0,
from /git/arm-soc/arch/arm/include/asm/irqflags.h:6,
from /git/arm-soc/include/linux/irqflags.h:15,
from /git/arm-soc/arch/arm/include/asm/bitops.h:27,
from /git/arm-soc/include/linux/bitops.h:36,
from /git/arm-soc/include/linux/kernel.h:10,
from /git/arm-soc/include/linux/list.h:8,
from /git/arm-soc/include/linux/module.h:9,
from /git/arm-soc/drivers/tty/serial/8250/8250_fintek.c:11:
arch/arm/include/uapi/asm/ptrace.h:55:0: note: this is the location of the previous definition
This renames the newly introduced 'IRQ_MODE' macro to FINTEK_IRQ_MODE.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4da22f1418 ("serial: 8250_fintek: fix the mismatched IRQ mode")
Link: https://patchwork.kernel.org/patch/9200119/
Acked-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #if defined(CONFIG_SERIAL_EARLYCON) && !defined(MODULE)
conditional has been added to the OF_EARLYCON_DECLARE() define.
The same conditional can be dropped from 8250_ingenic.c because
the unused symbols will be marked as __maybe_unsed.
Also, the Kconfig dependency can become much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
This commit partially reverts commit 3f5921a60f ("serial:
8250/mediatek: fix building with SERIAL_8250=m").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
Now we can revert commit a2d3ea2f23 ("serial: 8250/uniphier:
fix modular build").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that
replace following calls:
serial_out(port, UART_MCR, val)
serial_port_out(up, UART_MCR, val)
serial_in(port, UART_MCR)
This patch is needed in order to integrate reading/writing of MCR
signals via SERIAL_MCTRL_GPIO infrastructure later.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DNV, when RX DMA is used and number of bytes received is less than
transfer size, only RX DMA timeout interrupt is sent. When this happens,
read the RX buffer.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export serial8250_rx_dma_flush() for use by SOC UART drivers.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow other code to safely read DMA Channel Status Register (where
the register attribute for Channel Error, Descriptor Time Out &
Descriptor Done fields are read-clear), export hsu_dma_get_status().
hsu_dma_irq() is renamed to hsu_dma_do_irq() and requires Status
Register value to be passed in.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the 8250 as a boot console and the main console results in
messages being printed twice. The console framework will only
unregister boot consoles if a new console is registered with the
CON_CONSDEV flag set.
Set this flag for the univ8250 console to prevent double-registration.
Signed-off-by: Matthew Leach <matthew.leach@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for the WCH CH355 4S card in the 8250 serial driver.
Signed-off-by: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOS only use _OSI("Linux") to distinguish between Linux & Windows.
Apply Level/Low to UART trigger mode if Windows, Edge/High mode otherwise.
But since 2.6.23 the mainline kernel no longer returns true for
_OSI(“Linux”).
The default IRQ0~15 trigger mode in Linux is Edge/High mode without
ACPI MADT override. It mismatches IRQ mode and makes UART malfunctional on
such motherboard.
This patch will check the current IRQ mode and apply correct mode to UART.
The following link is F81216AD spec PDF:
http://html.alldatasheet.com/html-pdf/257956/FINTEK/F81216AD/5569/
25/F81216AD.html
LDN0~3
70h: IRQ channel & Mode register
Bit 6~5 :
00 : Active low level mode
01 : Active high edge mode
Bit 4 : Sharing Flag (0: not share/1: share)
Bit 3~0 : IRQ channel
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some board like Hisilicon D02 uses Synopsys DesignWare ABP UART, declare an
OF early console for it, so early console device can be enabled with comand
line "earlycon"(without option) via the "stdout-path" property in device-tree.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compiler complains about variables that are set, but never used:
* intX variables in exar_handle_irq
drivers/tty/serial/8250/8250_port.c:1864:34: warning: variable ‘int3’ set but not used [-Wunused-but-set-variable]
* val variable in pci_quatech_wqopr
drivers/tty/serial/8250/8250_pci.c:1139:10: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
And about a shadow variable:
* tmout in wait_for_xmitr is defined twice with the same type. Both of
them are also initialized before use.
Remove all of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert DEBUG_INTR to pr_debug:
* defined semantics (DEBUG, DYNAMIC_DEBUG)
* KERN_DEBUG level instead of KERN_DEFAULT
* emit __func__ and \n
* verified 'fmt' even when !DEBUG
I wonder if anybody ever used that or whether we should just drop the
lines.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hub6 and irqflags from struct old_serial_port are nowhere set. Drop
them from the structure and replace the reads by zeros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Commit cdcea058e5 ("serial: 8250_dw: Avoid serial_outx code duplicate
with new dw8250_check_lcr()") introduce a wrong logic when write val to
LCR reg. When CONFIG_64BIT enabled, __raw_writeq is used unconditionally.
The __raw_readq/__raw_writeq is introduced by commit bca2092d78 ("serial:
8250_dw: Use 64-bit access for OCTEON.") for OCTEON.
So for 64BIT && !PORT_OCTEON, we better to use coincident write function.
Fixes: cdcea058e510("serial: 8250_dw: Avoid serial_outx code duplicate with new dw8250_check_lcr()")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device HID AMDI0020 to match the AMD ACPI Vendor ID (AMDI) as
registered in http://www.uefi.org/acpi_id_list, and the UART
controller on future AMD paltform will use the HID instead of AMD0020.
Signed-off-by: Wang Hongcheng <annie.wang@amd.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek driver advertises as the PNP0501 driver; however this
conflicts with the standard 16550A uart PNP0501. The conflict causes
the 8250_fintek driver to load with _every_ PNP0501, but never probe,
and causing the entire 8250 driver stack to unload if the 8250_fintek
driver is unloaded (modprobe doesn't know that 8250_pnp rather than
8250_fintek claimed the resource).
This patch merges the Fintek driver into 8250_base. On autoconfig_16550
the device is probed to verify if it is a FINTEK device or not.
This custom probing can be disabled completely via configuration. When a
Fintek device is not probed it will behave as a standard 16550A device,
with no RS485 capabilities.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is not used outside the file, so it can be static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA completed normally does not require termination; only terminate
paused rx dma stemming from rx dma flush.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using fake IIR values to perform rx dma operations unnecessarily
conflates separate operations, stopping in-progress dma with starting
new dma.
Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma
[omap8250 already has equivalent omap_8250_rx_dma_flush()].
Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(),
and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering
in the irq handler with handle_rx_dma() helper.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the operation (restarting new rx dma) performed when error
argument is true.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c310c5c3 ("serial: 8250_dma: no need to sync RX buffer")
notes the RX DMA buffer is allocated from DMA coherent memory, and
thus does not need sync'd for each transaction. The same is true
for OMAP RX DMA.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaegine driver support terminate.
Query slave caps to determine if necessary commands/properties are
supported; disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaengine driver support error-free
pause/terminate and better-than-descriptor residue granularity. Query
slave caps to determine if necessary commands/properties are supported;
disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko