Also removed the bogus zeroing of fmt.sliced when setting up raw VBI.
This should have been removed in ivtv, but it was just copied-and-pasted
into cx18.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also removed the bogus zeroing of fmt.sliced when setting up raw VBI.
Switching between raw and sliced VBI changed in 2.6.28 and this memset
should have been removed at that time. It was never noticed because
the bridge driver will fill in the fmt.vbi values anyway.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only a relatively small number of video receivers and transmitters actually
support VBI. So start moving the vbi specific ops to an ops struct of their
own.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control step values reported by the device are used as a divisor
unchecked, which can result in a division by zero.
Check the step value and make it 1 when null.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC relative controls (exposure time, iris, focus, zoom, pan/tilt)
are write-only (despite the UVC specification stating that the GET_CUR
request is mandatory). Mark the controls as such, and report the related
V4L2 controls V4L2_CTRL_FLAG_WRITE_ONLY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Miricle 307K (17dc:0202) camera reports a 16-bit greyscale format,
support it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vivi uses find_font(), which is only available when FONTS
is enabled, so make vivi depend on FONTS.
ERROR: "find_font" [drivers/media/video/vivi.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the V4L2 specification, poll() should set POLLOUT | POLLWRNORM
flags for output devices after the frame has been displayed.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_pages_to_sg() and videobuf_vmalloc_to_sg() happen to create
a scatterlist element for every page. However, this is not true for
bus addresses, so other functions shouldn't rely on the length of the
scatter list being equal to nr_pages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf-core checks if .sync ops is defined before calling.
So, we don't need a do-nothing function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While analyzing one of the videobuf patches, I noticed that
videobuf_dma_sync is only used internally inside videobuf-dma-sg.
So, let's remove this function, merging the code at __videobuf_dma_sync()
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For recoverable stream errors dqbuf() now returns 0 and the error flag
is set instead of returning EIO.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I have 3 IVC-200 cards (with 4 video channels on each).
2 of the cards identify theirselves as 000[0-3]:a155 (ids already in
cardlist) and another one identifies itself as 080[0-3]:a155, which ids
were unknown so far.
Note - it's IVC-200, not IVC-200G.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch retrieve the correct mac address from the eeprom for TeVii
S470 card.
Signed-off-by: Pierre Gronlier <pierre.gronlier@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Serialize DVB initialization, to avoid it to happen while analog
initialization is still happening.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cx88-mpeg.c, there is code that sets core->input to CX88_VMUX_DVB.
However, this may be incorrect, since core->input is actually an
index to core->board.input[], which has not enough elements to be
indexed by the value of CX88_VMUX_DVB. So, the modified code searches
core->board.input[] for an input with a type of CX88_VMUX_DVB, and if
it does not find one, the index is simply set to zero.
The change may not have much effect, though, since it appears the only
case when core->input is actually used is when the current input is
being queried.
Signed-off-by: Istvan Varga <istvanv@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert drivers/media/video/cx231xx/cx231xx-input.c to not
rely on ir-functions.c.
(I do not have the hardware so I can only compile test this)
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pulse-distance is not a protocol, it is a line coding (used by some protocols,
like NEC). Looking at the uses of IR_TYPE_PD, the real protocol seems to be
NEC in all cases (drivers/media/video/cx88/cx88-input.c is the only user).
So, remove IR_TYPE_PD while it is still easy to do so.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
spin_is_locked() always returns zero when spinlock debugging is
disabled on a single CPU machine. Replace WARN_ON() with
assert_spin_locked().
Thanks to Laurent Pinchart for spotting this!
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Brightness is done by the gamma tables and not by single bridge registers.
It will be back as soon as an algorithm will be found.
This change also fixes the autogain problem found by Jose Alberto Reguero
(webcam 046d:08dd).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error was introduced by "gspca - zc3xx: Rename the USB sequences."
in commit e945e2e44c798f84494260c02478d3c23965bb93.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcams 0c45:613e may contain the sensors ov7630 or soi768.
A sensor probe is done at init time when the sensor is declared ov7630.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the V4L2 specification, applications set bytesused, field and
timestamp fields of struct v4l2_buffer when the buffer is intended for
output and memory type is MMAP. This adds proper copying of those values
to videobuf_buffer so drivers can use them.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Features Supported -
1. Provides V4L2 user interface for the video pipelines of DSS
2. Basic streaming working on LCD, DVI and TV.
3. Works on latest DSS2 library from Tomi
4. Support for various pixel formats like YUV, UYVY, RGB32, RGB24,
RGB565
5. Supports Alpha blending.
6. Supports Color keying both source and destination.
7. Supports rotation.
8. Supports cropping.
9. Supports Background color setting.
10. Allocated buffers to only needed size
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Murailidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for event handling to do_ioctl.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add event handling backend to V4L2. The backend handles event subscription
and delivery to file handles. Event subscriptions are based on file handle.
Events may be delivered to all subscribed file handles on a device
independent of where they originate from.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a set of new ioctls to the V4L2 API. The ioctls conform to
V4L2 Events RFC version 2.3:
<URL:http://www.spinics.net/lists/linux-media/msg12033.html>
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a list of v4l2_fh structures to every video_device.
It allows using file handle related information in V4L2. The event interface
is one example of such use.
The use of v4l2_fh is not mandatory for drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a virtual device driver for testing the memory-to-memory framework.
This virtual device uses in-memory buffers for both its source and destination.
It is capable of multi-instance, multi-buffer-per-transaction operation
(via the mem2mem framework).
[mchehab@redhat.com: use videobuf_queue_to_vaddr instead of the removed videobuf_queue_to_vmalloc]
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A mem-to-mem device is a device that uses memory buffers passed by
userspace applications for both their source and destination data. This
is different from existing drivers, which utilize memory buffers for either
input or output, but not both.
In terms of V4L2 such a device would be both of OUTPUT and CAPTURE type.
Examples of such devices would be: image 'resizers', 'rotators',
'colorspace converters', etc.
This patch adds a separate Kconfig sub-menu for mem-to-mem devices as well.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for more color effects (negative, sketch, emboss, etc) by
extending the v4l2_colorfx enum items.
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AK8814 only differs from AK8813 by included Macrovision Copy Protection
function. This patch adds a driver for AK8813 and AK8814 I2C PAL/NTSC TV
encoders.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of SuperH Mobile SoCs, including sh7724, include a Video Output Unit.
This patch adds a video (V4L2) output driver for it. The driver uses v4l2-subdev
and mediabus APIs to interface to TV encoders.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Current version of sh_mobile_ceu_camera.c interprets the V4L2 API specification
of the VIDIOC_S_CROP ioctl as "change input (for capture devices) area,
preserve scaling factors, therefore change output window," whereas a more
intuitive interpretation of the API is "change input area, preserve output
window." Switch sh_mobile_ceu_camera.c to use this interpretation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Clean up the code
- Use the kernel's built-in vga8x16 font instead of our own.
- Drop exclusive open: now multiple users can open the device as per the V4L2 spec.
- Move the format description to the vivi device instead of keeping it in the file
handle. Again as per the spec.
- Streamline and simplify the drawing code. It is now easy to add text on top of
the colorbar pattern.
- Upgrade the max resolution to 1920x1200.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/videobuf-dma-sg.c: In function ‘__videobuf_mmap_mapper’:
drivers/media/video/videobuf-dma-sg.c:557: warning: ‘size’ may be used uninitialized in this function
The condition where size is floating should never happen, due to the paranoia check,
but a future change at the logic might break it. So, let's just set size to zero and
use it for the paranoia check.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mmap_mapper should operate on a buffer, not on a complete queue. So let
the videobuf-core find the correct buffer instead of duplicating that
code in each mmap_mapper implementation.
The dma-sg implementation has backwards compatibility code for handling
the V4L1_COMPAT layer. This code is now under the v4L1_COMPAT config option.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_copy_to_user and copy_stream ops are almost identical for all
videobuf memtype variants. All that is needed is to use the new vaddr
op and these functions can be moved into the core, ensuring we have just
one single implementation instead of three.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ths function returns the virtual kernel address of the buffer and has
nothing to do with allocation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the .vmalloc op in struct videobuf_qtype_ops to .vaddr. This op returns
the virtual kernel address of a buffer. vaddr is a lot less confusing than
vmalloc since this callback does do any allocations.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_alloc() returned a void *. Change to struct videobuf_buffer *
to get better type checking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the mmap_free callback from struct videobuf_qtype_ops.
All implementations of this callback do the same trivial check: return
-EBUSY if any buffer is mmapped. That can also be tested in the
videobuf core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kref replaced as suggested in code review
uses atomic variable to track when it is ok to delete device
removes setting of video device parent, which is now
handled in v4l2_device.c
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_set_intfdata should not be used when using v4l2_device_register
and a non-NULL argument for the device.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a macro called dev_info that prints struct device specific
information. Having variables with the same name can be confusing and
prevents conversion of the macro to a function.
Rename the existing dev_info variables to something else in preparation
to converting the dev_info macro to a function.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return -EINVAL if we don't find the right query control id.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return -EINVAL if we don't find the control id.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Handle case of GSPCA=m, INPUT=m when building gspca core;
also handle case of INPUT=n by using stubs.
drivers/media/video/gspca/gspca.c:662: error: implicit declaration of function 'gspca_input_destroy_urb'
drivers/media/video/gspca/gspca.c:668: error: implicit declaration of function 'gspca_input_create_urb'
drivers/media/video/gspca/gspca.c:2284: error: implicit declaration of function 'gspca_input_connect'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hybrid tuner FMD1216MEX_MK3 after cold start has disabled IF. This
tuner has internal I2C switch. This switch switch I2C bus between DVB-T
and IF part. Default state is DVB-T. When module saa7134 is load it
can't find IF tda9887 and disable analog TV mode.
Sets internal I2C switch of the tuner to IF by send special value to the
tuner as for receive analog TV from low band. It can be usefule for
other cards.
I didn't set configure a tuner by a tuner model because this tuner can
have different I2C address. May be we can do it later after discuss for
more robust support a tuners.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return an error if the controller is not found.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code doesn't handle the situation where the controller is
not found.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return an error if the controller is not found.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"dev" is never NULL here so there is no need to check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
adding v4l2_device structure.
if one video_register_device call fails, allows use of other devices
or channels.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
big kernel lock removed from open function.
v4l2 code does not require locking the open function except
to check asynchronous firmware load state, which is protected
by a mutex
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
call to video_device_alloc was not being checked in probe function.
code simplified and uses video_device inside device structure.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The "AUVI_INPUT(tmp)" macro uses "tmp" as an index of an array with
AU0828_MAX_INPUT elements.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch fixes code that checks for CX88_VMUX_TELEVISION,
but not CX88_VMUX_CABLE. This prevented for example the audio standard
from being set when using the cable input.
Signed-off-by: Istvan Varga <istvanv@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
makes USB_PWC_INPUT_EVDEV to depend also on USB_PWC
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to obvious copy and paste coding a number of video capture drivers
which implement a limit on the buffer memory decremented the user
supplied buffer count in a while loop until it reaches an acceptable
value.
This is a silly thing to do when the maximum value can be directly
computed.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit bc52d6eb44.
On newer kernels, a saa7134 board stopped to display TV video output
properly. After a bisect, I found it as the commit causing the issue.
Turns out that v4l_bound_align_image isn't doing the same bounding
calculation as manually done previously in saa7134_try_fmt_vid_cap.
What isn't equal is the calculation done in clamp align, while
previously it did "f->fmt.pix.width &= ~0x03", clamp_align function
does "Round to nearest aligned value" as stated in the comment, which
yields a different result. If I comment the round calculation in
clamp_align like this: "x = (x /*+ (1 << (align - 1))*/) & mask",
I get it fixed too, because this way the calculation is the same then.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that video_ioctl2 no longer clobbers the argument for _IO() ioctls we
can move these into vidioc_default where they really belong.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Try to make a more sensible sequence of events in __video_do_ioctl: first
check for a valid ops pointer, then get the compat part done. The VIDIOCGMBUF
command is now part of the big switch.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that I have not been able to find anyone with this hardware. I tried
contacting the author without success, searched on eBay and similar places
without luck either.
So this conversion is untested. That said, it was pretty straightforward
so it is time to have this driver join the V4L2 world at last.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usbvision driver created vbi device nodes but the actual implementation
was just stubs and only returned errors to userspace.
In addition it used video_usercopy() and we want to remove that eventually.
So remove all the vbi code except for the vbi flag in the card definition
should someone ever be mad enough to work on a proper implementation for this
driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
You want to be able to reach the debug code at the end of this function,
so don't use return, use break.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the ioctl was defined without direction (e.g. _IO('o', 25)), then
the arg as passed to vidioc_default was NULL instead of the original
argument.
Several ioctls in e.g. include/linux/dvb/video.h and audio.h use this type
of ioctl to pass simple numerical values to the driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the kmalloc() failed for "ccdc_cfg = kmalloc(...);" then we would exit
with the lock held. I moved the mutex_lock() below the allocation
because it isn't protecting anything in that block and allocations are
allocations are sometimes slow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-raw-event.c is currently written with the assumption
that all "raw" hardware will generate events only on state change (i.e.
when a pulse or space starts).
However, some hardware (like mceusb, probably the most popular IR receiver
out there) only generates duration data (and that data is buffered so using
any kind of timing on the data is futile).
Furthermore, using signed int's to represent pulse/space durations is a
well-known approach when writing ir decoders.
With this patch:
- s64 int's are used to represent pulse/space durations in ns
- a workqueue is used to decode the ir protocols outside of interrupt context
- #defines are added to make decoders clearer
- decoder reset is implemented by passing a zero duration to the kfifo queue
and decoders are updated accordingly
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices have in-hardware Remote Controller decoder, while others
need a software decoder to get the IR code. As each software decoder
can be enabled/disabled individually, allowing multiple protocol
decoding capability.
On the other hand, hardware decoders have a limited protocol
support, often being able of decoding just one protocol each time.
So, each type needs a different set of capabilities to control the
supported protocol(s).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch that adds the rc-map changes didn't take into account that an
a table with IR_TYPE_UNKNOWN would make change_protocol to return -EINVAL.
As this function is fundamental to initialize some data, including a
callback to the getkey function, this caused the driver to stop working,
hanging the machine most of the times.
The fix were simply to add a handler for the IR type, but, to avoid further
issues, explicitly call change_protocol and handle the error before
initializing the IR. Also, let input_dev to start/stop IR handling,
after the opening of the input device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few hardware Remote Controller decoders, even using a standard protocol,
aren't able to provide the entire scancode. Due to that, the capability
of using other IR's are limited on those hardware.
Adds a way to indicate to ir-core what are the bits that the hardware
provides, from a scancode, allowing the addition of a complete IR table
to the kernel and allowing a limited support for changing the Remote
Controller on those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Andy Walls <awalls@md.metrocast.net> for pointing me his
code, that gave me some ideas to better implement it.
After some work with saa7134 bits, I found a way to catch both IRQ
edge pulses. By enabling it, the NEC decoder can now take both
pulse and spaces into account, making it more precise.
Instead of the old strategy of handling the events all at once,
this code implements a state machine. Due to that, it handles
individual pulse or space events, validating them against the
protocol, producing a much more reliable decoding.
With the new implementation, the protocol trailer bits are properly
handled, making possible for the repeat key to work.
Also, the code is now capable of handling both NEC and NEC extended
IR devices. With NEC, it produces a 16 bits code, while with NEC
extended, a 24 bits code is returned.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code that enables IRQ for the Remote Controller on saa7134 is a little
messy: it is outside saa7134-input, it checks if RC is GPIO based, and
it mixes both serial raw decode with parallel reads from a hardware-based
IR decoder.
Also, currently, it doesn't allow to trigger both transition edges at GPIO16
and GPIO18 lines. A rework on the code is needed to provide a better way
to specify what saa7134-input needs, maybe even moving part of the code from
saa7134-core and saa7134-cards into saa7134-input.
Yet, as a large rework is happening at RC core, it is better to wait until
the core changes stablize, in order to rework saa7134 RC internals.While
this don't happen, let's just change the logic a little bit to allow
enabling IRQ to be generated on both edge transitions, in order to better
support pulse/space raw decoders.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's an error at the IRQ2 bit map registers. Also, it doesn't
show what bits are needed for positive and for negative edge.
In the case of IR raw decoding, for some protocols, it is important
to detect both positive and negative edges. So, a latter patch
will need to use the other values.
Also, the code that detects problems on IRQ handling is incomplete,
as it disables only one of the IRQ bits for GPIO16 and GPIO18.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the ugly keymap sequences, use the new rc-*.ko keymap
files. For now, it is still needed to have one keymap loaded, for the
RC code to work. Later patches will remove this depenency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A latter patch will reuse the ir_input_register with a different meaning.
Before it, change all occurrences to a temporary name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaces most of the occurences of IR keytables on V4L drivers by a macro
that evaluates to provide the name of the exported symbol.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems impossible for ov to be NULL at this point.
The semantic match that finds the problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E, E1;
identifier f;
statement S1,S3;
iterator iter;
@@
if ((E == NULL && ...) || ...)
{
... when != false ((E == NULL && ...) || ...)
when != true ((E != NULL && ...) || ...)
when != iter(E,...) S1
when != E = E1
(
sizeof(E->f)
|
* E->f
)
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cap->driver is a 16 char buffer and dev->name is a 32 char buffer.
I don't see an actual problem, but we may as well make the static
checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Especially when IR needs to do polling, it generates lots of wakeups per
second. This makes no sense, if the input event device is closed.
Adds a callback handler to the IR hardware driver, to allow registering
an open/close ops.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some decoders and a lirc_dev interface may need some other operations to work.
For example: IR device register/unregister and ir_keydown events may need to
be tracked.
As some operations can occur in interrupt time, and a lock is needed to prevent
un-registering a decode while decoding a key, the lock needed to be convert
into a spin lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At raw_decode mode, the key is processed after the end of a timer. The
previous code resets the timer every time something is received at the IR
port. While this works fine with IR's that don't implement repeat, like
Avermedia RM-JX IR, it keeps waiting until keydown, on IR's that implement
NEC repeat command, like the Terratec yellow.
The solution is to change the behaviour to do the timeout after the first
received data.
The timeout is currently set to 15 ms, as it works fine with NEC protcocol.
It may need some adjustments to support other protocols and to better handle
spurious detections that may happen with some IR sensors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a method to pass IR raw pulse/code events into ir-core. This is
needed in order to support LIRC. It also helps to move common code
from the drivers into the core.
In order to allow testing, it implements a simple NEC protocol decoder
at ir-nec-decoder.c file. The logic is about the same used at saa7134
driver that handles Avermedia M135A and Encore FM53 boards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2 specification requires drivers to use the write events in the
file operations poll handler for output devices. The uvcvideo driver
erroneously used read events for all devices. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those control, as their names imply, control the camera aperture
settings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the STREAM_NO_FID quirk. Add a corresponding entry
in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_DEF quirk. Add a corresponding entry in
the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams handled by both sn9c102 or zc0301 and some gspca subdrivers
(sonixb, sonixj and zc3xx) were not handled when gspca was generated but
not the associated subdrivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the sequence streamon -> streamoff and again s_input, it fails
to lock the signal, since streamoff puts TVP514x into power off state
which leads to failure in sub-sequent s_input.
So add powerup sequence in s_routing (if disabled), since it is
important to lock the signal at this stage.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the devices like AM3517, it is expected that driver clears the
interrupt in ISR. Since this is device spcific, callback function
added to the platform_data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted this old V4L1 driver to V4L2.
I would like to thank Takeo Takahashi who very kindly tested this
driver for me. Much appreciated!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Takeo Takahashi <takahashi.takeo@renesas.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of completely unnecessary function prototypes.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of some "unused variable" warnings. These were the result of
sloppiness and should not have happened; I'll go stand in the corner now.
Reported-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That makes frame rate configuration persistent.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Cafe controller doesn't do non-SMBUS I/O, so we have to use it there.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow applications to play with the gain settings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Contrary to my earlier belief, the ov7670 is not actually an SMBUS device,
though it will pretend to be one if it's in a good mood. Unfortunately,
it's rarely in a good mood, especially on the XO 1.5. So use low-level i2c
I/O instead.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reading the clkrc register creates flaky behavior in some situations, and
we can easily track its state separately.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also provide for a longer delay after reset - the XO 1.5 needs it.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
card->driver is 15 characters and a NULL. The original code
goes past the end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
card->driver is 15 characters and a NULL, the original code could
cause a buffer overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support SPI bus to v4l2. Useful for control some device with SPI bus like
hardware MPEG2 encoders and etc.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for design which has an em2863/tvp5150 and uses the standard
empia USB ID. In Sander's case, it was branded as an "Eminent model EM3705"
Thanks to Sander Van Ginkel for testing and help debugging the support.
[mchehab@redhat.com: move it to a vague card number slot (card=29)]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that I merged a wrong version of the patch or that
changeset 4d770eeb926d0bc44c0bd68d051d3d2a5568ef41 got mangled somehow:
It were missed the #else to avoid compilation troubles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the ability to use the v4l2_ctrl_query_fill() function for the newly
introduced chroma gain control.
Also, make use of the centralized function by the one caller.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for chroma agc and gain to the saa7115 driver. This allows for
users to do manual adjustment for abnormal signal conditions.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enables the anti-alias filter, which was originally enabled for
the saa7113, but the saa7115_init_misc was trampling the value. Without this
patch, there would be visible vertical bands in the chroma.
Thanks to Andy Walls for helping test this change against other ivtv products.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the logic for tracking the amount of data copied to the VBI buffer, to
address problem found where the video lines are several bytes shifted to the
right (and the leading pixels in the first line rendered are garbage). This
would occur because the copy function would advance the pointer when detecting
headers, but the caller would not adjust the length actually copied.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It turns up we can reduce the starting line for the active area, which results
in more data being captured when under PAL (while the full VBI capture window
still stays properly encoded).
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the packets per URB count from 40 to 64. I suspect that whoever was
looking at the usbsnoop captures saw "0x40" packets and mistook it for "40".
As a result of this change, I can see a 25% reduction in the number of
interrupts generated via powertop.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hv7131d sensor code also works for the hv7131e, this patch changes
it to also recognize the hv7131e sensor id.
Tested-by: Frank Danapfel <fdanapfe@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_spca561: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix LED control on rev12a cameras and remove the unneeded
sd_stop0 callback function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed buggy init sequence for the OV9655 sensor.
Tested with a 0c45:6288 and 0c45:62b3.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for detecting webcams that are mounted
upside down in laptops. Currently the only two known
are two MSI modesl using the 0c45:624f.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop custom code for handling the input button in
favor of using gspca's input hanlding mechinism.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds new capture boards Hawell HW-404M7 and HW-808M7. Those cards have 4
or 8 SAA7130 chips and for the work it only needs initialize registers.
The value of those registers were dumped under Windows using flytest.
But board haven't EEPROM.
For the first chip:
SAA7130 (0x7130, SubVenID:1131, SubDevID:0000, Rev: 01)
I2C slave devices found:
No devices
GPIO pins:
Mode : 0x00389C00
Value: 0x00016C00
Video input: 3
Audio input: Analog Line1
For other chips:
SAA7130 (0x7130, SubVenID:1131, SubDevID:0000, Rev: 01)
I2C slave devices found:
No devices
GPIO pins:
Mode : 0x00389200
Value: 0x00010000
Video input: 3
Audio input: Analog Line1
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_ctrl_get_name(): add missing control names, and make title for
V4L2_CID_BG_COLOR consistent
V4L2_CID_AUTOBRIGHTNESS was introduced with kernel 2.6.31
V4L2_CID_BAND_STOP_FILTER was introduced with kernel 2.6.32
Signed-off-by: Frank Schaefer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In quickcam_messenger.c, if the NULL test on uvd is needed, then the
dereference should be after the NULL test.
In vpif_display.c, std_info is initialized to the address of a structure
field. This seems unlikely to be NULL. Test std_info->stdid instead.
In saa7134-alsa.c, the function is only called from one place, where the
chip argument has already been dereferenced. On the other hand, if it
should be kept, then card should be initialized after it.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of the magic number 0x28c0 used in several places in the ivtv and
ivtvfb driver and define the register address to a meaningful name.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changing the decoder video standard just prior to, or during, the output of
the lower field may result in a hard system lock. To avoid this, try to ensure
the firmware call occurs only during the first 100 lines of the top field.
(Minor comment addition and a line break added Andy Walls <awalls@radix.net>.)
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a guess at the proper configuration for component video on the Leadtek
PVR2100 and DVR3100 H.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some variants of the ASUS TV-FM 7135 are handled as the ASUSTeK P7131
Analog (card=146). However, by the time we find out, some
card-specific initialization is missed. In particular, the fact that
the IR is GPIO-based. Set it when we change the card type, and run
saa7134_input_init1().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, both driver and keytable names are exported to userspace. This
will help userspace to decide when a table need to be replaced
by another one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that setting this options to 50Hz can reduce the framerate, so it is
still disabled (60Hz) by default.
Signed-off-by: Mosalam Ebrahimi <m.ebrahimi@ieee.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Indent with tabs, not with spaces, nor with mixed style.
* Less indentation for controls index comments.
* Use lowercase hex digits.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also set default values unconditionally, for readability.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Adjust comments for sharpness control
* Set default value unconditionally, for readability
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set only the needed bits for AWB, and enable it by default.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Document that even if the state is a u8 value, both MSB and LSB are set
as sd->exposure represents half of the value we are going to set into
registers.
Skip setting exposure when AEC is enabled.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This also makes manual exposure actually work: it never worked before
because AEC was always enabled.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Use 'agc' instead of 'autogain' in the code so to align the naming
as in AEC/AWB.
* Tweak brightness and contrast default values.
* Fix setting/resetting registers values for AGC.
* Set actual gain back when disabling AGC.
* Skip setting GAIN register when AGC is enabled.
* Enable AGC by default.
Note that as Auto Gain Control is now enabled by default, if you are
using the driver for visual computing applications you might need to
disable it explicitly in your software.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hue control doesn't work and the sensor datasheet is not clear about how
to set hue properly.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove Blue/Red Channel Target Value, they are meant for Black Level
Calibration but it is not completely clear how to use them.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the change that stops the CX23415/6 firmware-intiiated secondary stream
appears to fix the temporal filter, it's now fully re-enabled for all capture
resolutions.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a capture is started, the firmware also appears to start a secondary
stream. Unless this secondary stream is also stopped, the encoder will remain
active and not reinitialise for the next capture. Unfortunately, setting up
the video source can glitch the encoder and result in undesirable effects that
this initialisation will clear.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Combine the two 150 ms delays into a single 300 ms delay. Ian Armstrong has
noted that the delay between CX2341X_ENC_INITIALIZE_INPUT and
CX2341X_ENC_START_CAPTURE can cause problems if the temporal filter is allowed
to be enabled.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IRQ from CAM disabled by default. In some environment enabled IRQ can cause of
machine freeze.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
adds hardware frame skipping using VIDIOC_S_PARM ioctl.
adds support for VIDIOC_ENUM_FRAMEINTERVALS.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the local functions static. Note that the function command_setlights() is
currently not called from anywhere.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'command_setformat' was not declared. Should it be static?
* symbol 'command_setcolourparams' was not declared. Should it be static?
* symbol 'command_setapcor' was not declared. Should it be static?
* symbol 'command_setvloffset' was not declared. Should it be static?
* symbol 'command_setexposure' was not declared. Should it be static?
* symbol 'command_setcolourbalance' was not declared. Should it be static?
* symbol 'command_setcompressiontarget' was not declared. Should it be static?
* symbol 'command_setyuvtresh' was not declared. Should it be static?
* symbol 'command_setcompressionparams' was not declared. Should it be static?
* symbol 'command_setcompression' was not declared. Should it be static?
* symbol 'command_setsensorfps' was not declared. Should it be static?
* symbol 'command_setflickerctrl' was not declared. Should it be static?
* symbol 'command_setecptiming' was not declared. Should it be static?
* symbol 'command_pause' was not declared. Should it be static?
* symbol 'command_resume' was not declared. Should it be static?
* symbol 'command_setlights' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adapts the changes submitted by Dainius Ridzevicius to the
linux-media mailing list on 8/14/09, to the current sources in order
to make the Kworld VS-DVB-T 323UR usb device work.
I also removed the "not validated" flag since I own the device and validated
that it works fine after the patch is applied.
Thanks to Devin Heitmueller for his guidance with the code.
Signed-off-by: Antonio Larrosa <larrosa@kde.org>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video status capability for inputs on Sensoray 2255 driver.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the range of exposure values (0-0x1770) distribute evenly through
HV7131R's exposure control bytes.
Signed-off-by: German Galkin <galkinga@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the local variables and functions static. Some of them are not exported by their
symbol name but used trough other means. For example a pointer of the operation
structure is passed through a function call.
This will remove the following sparse warnings (see "make C=1"):
* pd-video.c:20:5: warning: symbol 'usb_transfer_mode' was not declared. Should it be static?
* pd-video.c:621:5: warning: symbol 'fire_all_urb' was not declared. Should it be static?
* pd-video.c:881:5: warning: symbol 'vidioc_s_std' was not declared. Should it be static?
* pd-video.c:1024:5: warning: symbol 'vidioc_g_audio' was not declared. Should it be static?
* pd-video.c:1033:5: warning: symbol 'vidioc_s_audio' was not declared. Should it be static?
* pd-video.c:1193:5: warning: symbol 'usb_transfer_stop' was not declared. Should it be static?
* pd-video.c:1522:14: warning: symbol 'pd_video_poll' was not declared. Should it be static?
* pd-video.c:1528:9: warning: symbol 'pd_video_read' was not declared. Should it be static?
* pd-radio.c:164:5: warning: symbol 'tlg_fm_vidioc_g_tuner' was not declared. Should it be static?
* pd-radio.c:206:5: warning: symbol 'fm_get_freq' was not declared. Should it be static?
* pd-radio.c:249:5: warning: symbol 'fm_set_freq' was not declared. Should it be static?
* pd-radio.c:261:5: warning: symbol 'tlg_fm_vidioc_g_ctrl' was not declared. Should it be static?
* pd-radio.c:267:5: warning: symbol 'tlg_fm_vidioc_g_exts_ctrl' was not declared. Should it be static?
* pd-radio.c:288:5: warning: symbol 'tlg_fm_vidioc_s_exts_ctrl' was not declared. Should it be static?
* pd-radio.c:315:5: warning: symbol 'tlg_fm_vidioc_s_ctrl' was not declared. Should it be static?
* pd-radio.c:321:5: warning: symbol 'tlg_fm_vidioc_queryctrl' was not declared. Should it be static?
* pd-radio.c:340:5: warning: symbol 'tlg_fm_vidioc_querymenu' was not declared. Should it be static?
* pd-main.c:58:12: warning: symbol 'firmware_name' was not declared. Should it be static?
* pd-main.c:59:19: warning: symbol 'poseidon_driver' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When power management is not configured (CONFIG_PM) then some code is no longer
necessary.
This patch will remove the following compiler warnings:
* pd-dvb.c: In function 'poseidon_fe_release':
* pd-dvb.c:101: warning: unused variable 'pd'
* pd-video.c:14: warning: 'pm_video_suspend' declared 'static' but never defined
* pd-video.c:15: warning: 'pm_video_resume' declared 'static' but never defined
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When temporarily there is no video signal, sometimes it takes more than 0.5
secs for the cx88 chip to generate a single frame. If a dma timeout occurs
during recording, it confuses the recording application (at least mencoder)
and the recording stops.
Since there is already an #if 0 for 2 seconds buffer timeout in the code
at the -hg development tree, re-enabling that seemed the most simple
solution.
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the platform hooks are provided, soc_camera powers off the device
on close and powers it on on open. This resets the ADDRESS_MODE registers
which then can be different to the value the driver has computed for them.
This patch setups runtime pm usage for mt9t031 and uses the resume function
to write the ADDRESS_MODE registers in order to fix the above described
problem.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To save power soc-camera powers subdevices down, when they are not in use,
if this is supported by the platform. However, the V4L standard dictates,
that video nodes shall preserve configuration between uses. This requires
runtime power management, which is implemented by this patch. It allows
subdevice drivers to specify their runtime power-management methods, by
assigning a type to the video device.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This will remove the following sparse warning (see "make C=1"):
* incorrect type in argument 1 (different signedness)
expected unsigned int *start
got signed int *<noident>
as well as a couple more signedness mismatches.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the fifo reset from pxa_camera_start_capture to pxa_camera_irq direct
before the dma start after an end of frame interrupt to prevent images from
shifting because of old data at the begin of the frame.
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_mbus_bytes_per_line() returns -EINVAL on error but we store it in an
unsigned int so the test for less than zero doesn't work. I think it
always returns "small" positive values so we can just cast it to int
here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a regression of
7d58289 (mx1: prefix SOC specific defines with MX1_ and deprecate old names)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An earlier regression fix for the mxb driver (V4L/DVB: saa7146_vv: fix
regression where v4l2_device was registered too late) caused a new
regression in the av7110 driver.
Reverted the old fix and fixed the problem in the mxb driver instead.
Tested on mxb and budget-av cards.
The real problem is that the saa7146 framework has separate probe()
and attach() driver callbacks which should be rolled into one. This
is now done for the mxb driver, but others should do the same. Lack
of hardware makes this hard to do, though. I hope to get hold of some
hexium cards and then I can try to improve the framework to prevent
this from happening again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As part of upstream merge, set_params() function was removed from isif.c.
This requires removal of BUG_ON() and check for set_params ptr in
vpfe_capture.c. Without this kernel crash dump is seen while bootup on DM365
Also made following changes:-
1) converted error messages to debug messages since it is not right to flood
the console with error messages for user mistakes.
2) returns -EINVAL if ioctl is not supported
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 0461:0815 camera is spca561 based not spca508
Signed-off-by: John Ellson <john.ellson@comcast.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 046d:08da usb id shouldn't be associated with the stv06xx driver as they're
not compatible with each other.
This fixes a bug where Quickcam Messenger cams fail to use its proper driver
(gspca-zc3xx), rendering the camera inoperable.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
CC: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a bug in vpfe_probe() that doesn't call mutex_unlock() if memory
allocation for ccdc_cfg fails. See also the smatch warning report from Dan
Carpenter that shows this as an issue.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous loop goes until last == VIDEO_MAX_FRAME, so this could
potentially go one past the end of the loop.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Made necessary by 6992f53349 ("sysfs: Use
one lockdep class per sysfs attribute").
Prevents further "key xxx not in .data" bug-reports. Although some
attributes could probably be converted to static ones, this is left for
people having hardware to test.
Found by this semantic patch:
@ init @
type T;
identifier A;
@@
T {
...
struct device_attribute A;
...
};
@ main extends init @
expression E;
statement S;
identifier err;
T *name;
@@
... when != sysfs_attr_init(&name->A.attr);
(
+ sysfs_attr_init(&name->A.attr);
if (device_create_file(E, &name->A))
S
|
+ sysfs_attr_init(&name->A.attr);
err = device_create_file(E, &name->A);
)
While reviewing, I put the initialization to apropriate places.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <gregkh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Mike Isely <isely@pobox.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
A pointer to omap24xxcam_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is not needed, since the function already do it. Also, it causes
a warning at the compilation, since a new var is declared in the middle
of the code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the built-in dvb device
of a Samsung SMT7020s (x86 based STB) to the cx88 family.
Signed-off-by: Dirk Herrendoerfer <d.herrendoerfer@herrendoerfer.name>
Signed-off-by: Helmut Auer <helmut@helmutauer.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only tested with an stv6422 based cam, as that is the only stv06xx cam
I have with a button.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitations this only works while the camera is
streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitations this only works while the camera is
streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note due to hardware limitiations (no interrupt endpoint), this only works
when the camera is streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_main: Fix a compile error when CONFIG_INPUT is not set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2 small changes to input device error handling:
1) Make it fatal when we fail to create an input device (it is either this
or add checks for gspca_dev->input_dev being NULL in a lot of places)
2) Since we allow gspca_input_create_urb() to fail everywhere we call it,
and thus never check its return value, make it void.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow use of the gspca core input device creation code by subdrivers which
have non interrupt driven camera buttons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil