All users now setup a fixed regulator for the vbus supply. We can drop
the vbus GPIO code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Historically the power supply management in this driver has been handled
in two separate places in parallel. Device-tree users simply defined an
appropriate regulator, while two boards with no DT support (da830-evm and
omapl138-hawk) passed functions defined in their respective board files
over platform data. These functions simply used legacy GPIO calls to
watch the oc GPIO for interrupts and disable the vbus GPIO when the irq
fires.
Commit d193abf1c9 ("usb: ohci-da8xx: add vbus and overcurrent gpios")
updated these GPIO calls to the modern API and moved them inside the
driver.
This however is not the optimal solution for the vbus GPIO which should
be modeled as a fixed regulator that can be controlled with a GPIO.
In order to keep the overcurrent protection available once we move the
board files to using fixed regulators we need to disable the enable_reg
regulator when the overcurrent indicator interrupt fires. Since we
cannot call regulator_disable() from interrupt context, we need to
switch to using a oneshot threaded interrupt.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There's no reason to have a separate variable to keep track of the
regulator state. The regulator core already does that. Remove
reg_enabled from struct da8xx_ohci_hcd.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In case create_singlethread_workqueue fails, the fix notifies
callers the error to avoid potential NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled
move the memory cleanup outside the spinlock
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- add debugfs support for dumping dma-debug information (Corentin Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
-----BEGIN PGP SIGNATURE-----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=nAMI
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
- add debugfs support for dumping dma-debug information (Corentin
Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
* tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping: (21 commits)
Documentation/DMA-API-HOWTO: update dma_mask sections
sparc64/pci_sun4v: allow large DMA masks
sparc64/iommu: allow large DMA masks
sparc64: refactor the ali DMA quirk
ccio: allow large DMA masks
dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
dma-mapping: remove dma_mark_declared_memory_occupied
dma-mapping: move CONFIG_DMA_CMA to kernel/dma/Kconfig
dma-mapping: improve selection of dma_declare_coherent availability
dma-mapping: remove an incorrect __iommem annotation
of: select OF_RESERVED_MEM automatically
device.h: dma_mem is only needed for HAVE_GENERIC_DMA_COHERENT
mfd/sm501: depend on HAS_DMA
dma-mapping: add a kconfig symbol for arch_teardown_dma_ops availability
dma-mapping: add a kconfig symbol for arch_setup_dma_ops availability
dma-mapping: move debug configuration options to kernel/dma
dma-debug: add dumping facility via debugfs
dma: debug: no need to check return value of debugfs_create functions
videobuf2: replace a layering violation with dma_map_resource
dma-mapping: don't BUG when calling dma_map_resource on RAM
...
Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates (you will
have a merge issue with Kconfig and Makefile), xhci updates, and typec
additions. Also included in here are a lot of small cleanups and fixes
and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+hsw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynfNwCgqKKg+MxJ9pFjrwfWYOrbk+BBe2UAn2Elp4ia
8FTdneQfN2J8Hhc6KGXE
=Kx9I
-----END PGP SIGNATURE-----
Merge tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates, xhci
updates, and typec additions. Also included in here are a lot of small
cleanups and fixes and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
wusb: Remove unnecessary static function ckhdid_printf
usb: core: make default autosuspend delay configurable
usb: core: Fix typo in description of "authorized_default"
usb: chipidea: Refactor USB PHY selection and keep a single PHY
usb: chipidea: Grab the (legacy) USB PHY by phandle first
usb: chipidea: imx: set power polarity
dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
usb: chipidea: imx: remove unused header files
usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
usb: core: add option of only authorizing internal devices
usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
usb: xhci: fix build warning - missing prototype
usb: xhci: dbc: Fixing typo error.
usb: xhci: remove unused member 'parent' in xhci_regset struct
xhci: tegra: Prevent error pointer dereference
USB: serial: option: add Telit ME910 ECM composition
usb: core: Replace hardcoded check with inline function from usb.h
usb: core: skip interfaces disabled in devicetree
usb: typec: mux: remove redundant check on variable match
...
This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build warning when building drivers/usb/host/xhci-mem.o with W=1 due
to missing prototype for xhci_free_virt_devices_depth_first.
This function is only used in xhci-mem.c so just make it static.
Signed-off-by: Jean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member @parent of xhci_regset struct is not used in fact,
so remove it
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes: 6494a9ad86 ("usb: xhci: tegra: Add genpd support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users of dma_declare_coherent want their allocations to be
exclusive, so default to exclusive allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/oxu210hp-hcd.c: In function 'scan_periodic':
drivers/usb/host/oxu210hp-hcd.c:2256:13: warning:
variable 'uframes' set but not used [-Wunused-but-set-variable]
drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_urb_enqueue':
drivers/usb/host/oxu210hp-hcd.c:2835:6: warning:
variable 'transfer_buffer_length' set but not used [-Wunused-but-set-variable]
They are never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DaVinci SoC updates for v5.1 (part 2)
This pull request contains changes needed to help get rid of
hard-coded GPIO base value passed from DaVinci platform data.
The OHCI related changes also help by moving over-current support
from board-files to OHCI driver making future DT-coversion easy.
The OHCI parts are acked by its maintainer.
* tag 'davinci-for-v5.1/soc-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
usb: ohci-da8xx: remove unused callbacks from platform data
ARM: davinci: da830-evm: remove legacy usb helpers
ARM: davinci: omapl138-hawk: remove legacy usb helpers
usb: ohci-da8xx: add vbus and overcurrent gpios
ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
usb: ohci-da8xx: add a helper pointer to &pdev->dev
usb: ohci-da8xx: add a new line after local variables
ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
ARM: davinci: mityomapl138: use device properties for at24 eeprom
ARM: davinci: mityomapl138: use nvmem notifiers
ARM: davinci: remove dead code related to MAC address reading
ARM: davinci: sffsdr: use device properties for at24 eeprom
ARM: davinci: sffsdr: fix the at24 eeprom device name
ARM: davinci: dm646x-evm: use device properties for at24 eeprom
ARM: davinci: dm644x-evm: use device properties for at24 eeprom
ARM: davinci: da830-evm: use device properties for at24 eeprom
ARM: davinci: dm365-evm: use device properties for at24 eeprom
ARM: davinci: mityomapl138: don't read the MAC address from machine code
ARM: davinci: da850-evm: remove dead MTD code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A statement is indented too deeply, fix this by removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two users upstream which register external callbacks for
switching the port power on/off and overcurrent protection. Both
users only use two GPIOs for that. Instead of having that functionality
in the board files, move the logic into the OHCI driver - including
the interrupt handler for overcurrent detection.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a helper pointer to &pdev->dev. This improves readability by
removing all the &pdev->dev dereferencing.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a new line after local variables. This improves the coding style.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
No need to initialize the PHY from the driver's probe. It is done by
the core automatically and doing it twice would increment the
phy->powercount counter to 2 instead of 1. During later suspend
operation, the counter will be decremented to one, no phy->power_off()
will occur and worse than that, the following phy->power_on() at
resume time will also be skipped, failing the whole S2RAM operation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvebu xHCI host driver does not have suspend/resume support. Use of
the XHCI_RESET_ON_RESUME quirk is mandatory in order to avoid failures
after resume. This will work only if no USB device is plugged-in.
While at it, mention in the Kconfig file that this IP is also present
on the A3700 SoC.
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
[miquel.raynal@bootlin.com: Reword the commit message]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have been using Makefile for well over a decade now, use that name
instead of Kbuild.
Also, while moving the file, add the proper SPDX identifier at the top
of it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove USB errata checking code from driver. Applicability of erratum
is retrieved by reading corresponding property in device tree.
This property is written during device tree fixup.
Besides, replace spaces with tabs to make code aligned.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_USB_EHCI_FSL is not dependent on FSL_SOC, it can be built on
non-PPC platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arm/arm64's io.h doesn't define clrbits32() and clrsetbits_be32(), which
causing compile failure on some Layerscape Platforms (such as LS1021A and
LS2012A which also integrates FSL EHCI controller). So use
ioread32be()/iowrite32be() instead to make it workable on both
powerpc and arm.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add this SFR compatible definition for the sam9x60 SoC and manage
its use in ohci-at91.c driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are two statements that are indented incorrectly and need
to be moved to a new line. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.
If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.
This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.
Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the dev->iommu_group check with a proper function
call that better reprensents its purpose.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring, no functional changes.
But worth mentioning that checking for port link resume state is now behind
a additional port power check.
This is fine as ports can't be in resume state if port power bit is not
set.
xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be
set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume,
and RExit states.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move U0 link state handing to USB3 and USB2 specific functions
Note that
bus_state->resuming_ports:
bus_state->resume_done[]:
are only used for USB2, and don't need to cleared for USB3 ports
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Group the code where the wPortstatus and wPortChange bits
are set into one place.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state
is reported if xhci port link is in U2 AND port is powered.
Previously we did not check if the port was powered, but according to
xhci spec 4.19.1.1.6 All the 'Enabled' states, including
USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that each root hub has their own bus_state strucure the
hcd_undex() used to get the correct bus_state strucure is
no longer needed.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is introduced for the pre-0.96 xHC controllers, and the driver only
support HW LPM for 1.0 and later controllers.It's not actually used now
and is thought not to be used in the future any more, so just remove it.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Observed "TRB completion code (27)" error which corresponds to Stopped -
Length Invalid error(xhci spec section 4.17.4) while connecting USB to
SATA bridge.
Looks like this case was not considered when the following patch[1] was
committed. Hence adding this new check which can prevent
the invalid byte size error.
[1] ade2e3a xhci: handle transfer events without TRB pointer
Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing NULL pointer dereference.
Check if xhci->shared_hcd is still valid before handing USB3 port events
Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()
The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)
Afer commit fe190ed0d6 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.
shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.
xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them")
Fixes: fe190ed0d6 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_pool_destroy() can handle NULL pointer correctly, so there is
no need to check NULL pointer before calling dma_pool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
The generic power-domain framework has been updated to allow devices
that require more than one power-domain to create a new device for
each power-domain required and then link these new power-domain
devices to the consumer device.
Update the Tegra xHCI driver to use the new APIs provided by the
generic power-domain framework so we can use the generic power-domain
framework for managing the xHCI controllers power-domains. Please
note that to maintain backward compatibility with older device-tree
blobs these new generic power-domain APIs are only used if the
'power-domains' property is present and otherwise we fall back to
using the legacy Tegra APIs for managing the power-domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the XUSB power domains used by the Tegra xHCI controller are
never powered off on the removal of the driver, however, they will be
powered off on probe failure. Update the removal code to be consistent
with the probe failure path to power off the XUSB power domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel,oc-gpio is optional. Request its irq only when atmel,oc is set
in device tree.
devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its
return value for NULL before error, because it is more probable that
atmel,oc is not set.
This fixes the following errors on boards where atmel,oc is not set in
device tree:
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Apollo Lake has the same internal USB role mux as
Intel Cherry Trail.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give USB3 devices a better chance to enumerate at USB3 speeds if
they are connected to a suspended host.
Porting from "671ffdff5b13 xhci: resume USB 3 roothub first"
Cc: <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workaround for missing CAS bit is also needed for xHC on Intel
sunrisepoint PCH. For more details see:
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.
This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.
This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to autoresume/autosuspend
root hub properly.
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XUSB firmware header is in little endian byte order, so make the
fields __le32 and __le16 instead of u32 and u16 to avoid warnings from
sparse when the fields are used with the endian-aware __le32_to_cpu()
and __le16_to_cpu() accessors, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci controller on Alpine and Titan Ridge keeps the whole thunderbolt
awake if the host controller is not allowed tp sleep.
This is the case even if no USB devices are connected to the host.
Because of this bigger impact, allow runtime pm as default for these xhci
controllers in the driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use soft retry to recover from a USB Transaction Errors that are caused by
temporary error conditions. The USB device is not aware that the xHC
has halted the endpoint, and will be waiting for another retry
A Soft Retry perform additional retries and recover from an error which has
caused the xHC to halt an endpoint.
Soft retry has some limitations:
Soft Retry attempts shall not be performed on Isoch endpoints
Soft Retry attempts shall not be performed if the device is behind a TT in
a HS Hub
Software shall limit the number of unsuccessful Soft Retry attempts to
prevent an infinite loop.
For more details on Soft retry see xhci specs 4.6.8.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPL support is used to identify targeted devices during
EH2.0 and EH3.0 certification test, the user can add "tpl-support"
at dts to enable this feature.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supports SSP scheduling only for SSP device directly connected
to root hub but not through external USB3 gen2 hub which need
use a new scheduling way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mainly improve SuperSpeed ISOC bandwidth in last microframe,
and LowSpeed/FullSpeed IN INT/ISOC bandwidth in split and
idle microframes by introduing a bandwidth budget table;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the interval equal zero, needn't round up to power of two
for the number of packets in each ESIT, so fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of maximum ESIT payload of endpoint context to calculate
the number of packets to send in each ESIT
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's dangerous to use empty code define.
Furthermore it lead to the following warning:
"suggest braces around empty body in an « else » statement"
So let's replace emptyness by "do {} while(0)"
Furthermore, as suggested by Joe Perches, rename the macro to INCR.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is code in the .remove() hook to handle the drvdata
being NULL, for good reasons: it is never set, so it will
always be NULL. As I moved code around, static checkers
start complaining.
Instead of this, make sure to always set it on successful
probe so we can always dereference it on the remove path.
Use the platform_device_[set|get]_drvdata() since this is
a platform device.
Fixes: ffa8a31b5b ("usb: host: fotg2: add silicon clock handling")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a proper PHY driver, instead of hooks to a board support package.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done do that it could be enabled alongside other platform EHCI
glue drivers on multiplatform kernels.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MTK xHCI controller use some reserved bytes in endpoint context for
bandwidth scheduling, so need keep them in xhci_endpoint_copy();
The issue is introduced by:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
It resets endpoints and will drop bandwidth scheduling parameters used
by interrupt or isochronous endpoints on MTK xHCI controller.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul pointed out that the 50-ms sleep during OHCI initialization takes
up a large fraction of a system's boot time. Things get worse when
there are two OHCI controllers present, each requiring 50 ms.
However, there really is no need to send a 50-ms reset signal out all
the root-hub ports during initialization. The ports themselves will
be disabled, and the only way to enable a port is to reset it.
Therefore all attached USB devices will receive a proper reset in any
case. The controller reset does not need to be long enough to reset
those other devices, so the 50-ms delay isn't necessary.
Without the delay, there is no remaining incentive for skipping the
reset when the controller is already in the RESET state. This patch
removes the test, issuing the command unconditionally, and removes the
following delay.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When used in a system with software-controlled silicon clocks,
the FOTG210 needs to grab, prepare and enable the clock.
This is needed on for example the Cortina Gemini, where the
platform will by default gate off the clock unless the
peripheral (in this case the USB driver) grabs and enables
the clock.
If there is no clock available on the platform, we live
without it. Make sure to percolate probe deferrals.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.
[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
i_usX2Y_urb_complete in i_usX2Y_subs_startup
Note that [FUNC_PTR] means a function pointer call is used.
To fix this bug, msleep() is replaced with mdelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_plat_probe() both sysdev and pdev->dev are being used
for finding quirks. There are some drivers(like dwc3 host.c)
which adds quirks(like usb3-lpm-capable) into pdev and the logic
present in xhci_plat_probe() checks for quirks in either sysdev
or pdev for finding the quirks. Because of this logic, some of
the quirks are getting missed(usb3-lpm-capable quirk added by dwc3
host.c driver is getting missed).This patch fixes this by iterating
over all the available parents for finding the quirks. In this way
all the quirks which are present in child or parent are correctly
updated.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bartosz Golaszewski