We will check if any hidden SSID found in passive scan channels
and do specific SSID active scan for those channels.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware dump feature for SD8997 chipset.
The difference here is only one memory type is needed
to save all firmware information. Device dump information
will be uploaded to usersapace file.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for 8997 chipset to mwifiex
with SDIO/PCIe/USB interface.
The corresponding firmware image files are located in:
"mrvl/sd8997_uapsta.bin"
"mrvl/pcie8997_uapsta.bin"
"mrvl/usb8997_uapsta.bin"
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code returns success if kmalloc fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this driver, two variables are masked by one quantity, and then tested
against a second number with more bits that the mask. Accordingly, the
test always fails. To minimize the possibility of such typos, a symbolic
definition of the mask is created and used.
The separate load and mask operations are also combined into a single
statement.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The drivers are converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit e996db6983 (rtlwifi: rtl8192c: Add init codes for "fw_version"
and "fw_subversion") added initialization for fw_version, but failed to
note that the variable in the firmware header is little-endian. The
following Sparse warning results:
CHECK drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: warning: incorrect type in assignment (different base types)
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: expected unsigned short [unsigned] [usertype] fw_version
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: got restricted __le16 [usertype] version
When fixing this problem, I noticed that several of the drivers contain
nearly identical copies of the firmware header struct, and that only the one
used in rtl8192c{e,u} had correct endian notation. The struct has been
moved into a common header, and the other drivers will be fixed in
subsequant patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/link.c:197
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/wmi.c:331
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_drv_init.c:81
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_hst.c:171
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:277
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:206
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware peer entries are involved in internal
firmware vdev structures. This was not accounted
for and could lead firmware to crash due to asking
it to do more than it could.
Fixes: 039a0051ec ("ath10k: allocate fw resources for iface combinations")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If peer creation failed during offchannel Tx the
driver attempted to delete the peer nonetheless.
This caused the ar->num_peers counter to be
incorrectly decremented. This subsequently could
cause the counter to drop below 0 and also
eventually lead to firmware crash because host
would think there are less peer entries created in
firmware then there really were.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When WoWLAN resume fails with retval 1 mac80211
will attempt to reconfig the device in a similar
manner when hw restart is requested. This wasn't
handled properly and yielded call trace warnings
and the device ended up not working.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware did not have any feature flags set the
var would be left with values found on the stack
(i.e. garbage) yielding print string like this:
(...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E
Fixes: b27bc5a40f ("ath10k: dump fw features during probing")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables MU-MIMO transmit beamforming support
for QCA99X0 chipsets.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d ("ath10k: unregister and remove frag_threshold callback")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 1010ba4c5d ("ath10k: unregister and
remove frag_threshold callback") didn't remove all
instances of (futile) fragmentation threshold
configuration. No known firmware supports the
parameter so don't even bother setting it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to firmware engineers, the firmware has never required
these fields and the values have always been calculated, they were
just leftovers from a previous implementation.
Therefore remove the unnecessary calculation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If register_hdlc_device() fails, the current code returns 0 but we
should return an error code instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use the IS_ERR_VALUE() macro for checking
the return value from pm_runtime_* functions.
Just do a simple negative test instead.
The semantic patch that makes this change is available
in scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs support to dump tid info like stid, sftid, tids, atid and
hwtids
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For T4 adapter, offloaded servers tid for IPv4 connections are
allocated from filter region. So add a new field for server filter tid if
server tid is allocated from filter region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the tid info, differentiate from which region the TID is allocated
from. It can be from TCAM region or HASH region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding more details to sge qinfo for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This BQL implementation is mostly derived from its related driver, alx.
Tested on AR8131 (rev c0) [1969:1063]. Saturated a 100mbps link with 5
concurrent runs of netperf. Ping latency dropped from 14ms to 3ms.
Signed-off-by: Ron Angeles <ronangeles@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current filer rule optimization is broken in several ways:
(1) Can perform reads/writes beyond end of allocated tables.
(gianfar_ethtool.c:1326).
(2) It breaks badly for rules with more than 2 specifiers
(e.g. matching ip, port, tos).
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: TOS == 00000003 AND Q:00 ctrl:0000008a prop:00000003
05: DIA == 0a000003 AND Q:11 ctrl:0000448c prop:0a000003
06: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
07: TOS == 00000002 AND Q:00 ctrl:0000008a prop:00000002
08: DIA == 0a000002 AND Q:09 ctrl:0000248c prop:0a000002
09: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
0a: DPT == 00000001 AND Q:00 ctrl:0000008e prop:00000001
0b: TOS == 00000001 CLE Q:01 ctrl:0000060a prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
(Entire cluster gets AND-ed together).
(3) We observed that the masking rules it generates do not
play well with clustering on P2020. Only first rule
of the cluster would ever fire. Given that optimizer
relies heavily on masking this is very hard to fix.
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: DIA == 0a000003 Q:11 ctrl:0000440c prop:0a000003
05: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
06: DIA == 0a000002 Q:09 ctrl:0000240c prop:0a000002
07: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
08: DPT == 00000001 CLE Q:01 ctrl:0000060e prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules. We found no errata covering this.
The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: Aleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_FILER_IDX is the last usable index. Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the use of ethtool --set-channels devname combined N to
change the number of vRSS queues. Separate rx, tx, and other parameters
are not supported. The maximum is rsscap.num_recv_que. It passes the
given value to rndis_filter_device_add through the device_info->num_chn
field.
If the procedure fails, it attempts to recover to the prior state. If
the recovery fails, it logs an error and aborts.
Current num_chn is saved and restored when changing the MTU.
Signed-off-by: Andrew Schwartzmeyer <andschwa@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uses device_info->num_chn to pass user provided number of vRSS
queues (from ethtool --set-channels) to rndis_filter_device_add. If
nonzero and less than the maximum, set net_device->num_chn to the given
value; else default to prior algorithm.
Always initialize struct device_info to 0, otherwise not all its fields
are guaranteed to be 0, which is necessary when checking if num_chn has
been purposefully set.
Signed-off-by: Andrew Schwartzmeyer <andschwa@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first slave is added (such as during bootup) the first
gratuitous ARP gets dropped. We don't see this drop during a failover.
The packet gets dropped in qdisc (noop_enqueue).
The fix is to delay the sending of gratuitous ARPs till the bond dev's
carrier is present.
It can also be worked around by setting num_grat_arp to more than 1.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime. Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.
We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an ndm_state member to the switchdev_obj_fdb structure,
in order to support static FDB addresses.
Set Rocker ndm_state to NUD_REACHABLE.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a low level _mv88e6xxx_atu_getnext function for convenient access to
the hardware, and rework the FDB Get Next operation.
This will ease the future integration with VLAN IDs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mv88e6xxx_atu_entry structure and a low level function for the ATU
Load operation, and provide FDB add and delete wrappers functions.
This implementation handles the eventual trunk mapping. If the related
bit is set, then the ATU data register would contain the trunk ID, and
not the port vector.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the prototype of port_getnext to include a vid parameter.
This is necessary to introduce the support for VLAN.
Also rename the fdb_{add,del,getnext} function pointers to
port_fdb_{add,del,getnext} since they are specific to a given port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the __mv88e6xxx_{read,write}_addr functions to more explicit
_mv88e6xxx_atu_mac_{read,write} functions, which also respect the single
underscore convention used in the file (meaning SMI lock must be held).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently manages one FID per port (or bridge group), with a
mask of DSA_MAX_PORTS bits, where 0 means that the FID is in use.
The Marvell 88E6xxx switches support up to 4094 FIDs (from 1 to 0xfff;
FID 0 means that multiple address databases are not being used).
This patch changes the fid_mask for an fid_bitmap of 4096 bits.
>From now on, FIDs 1 to num_ports are reserved for non-bridged ports and
bridge groups (a bridge group gets the FID of its first member). The
remaining bits will be reserved for VLAN entries.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define register GLOBAL_ATU_FID instead of the raw value 0x01.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way to get the MAC address in a firmware
independent manner, so set the MAC address of the device directly from
the ACPI tables.
The binding agrees with the proposed standard here:
http://www.uefi.org/sites/default/files/resources/nic-request-v2.pdf
Based on code from: Narinder Dhillon <ndhillon@cavium.com>
Tomasz Nowicki <tomasz.nowicki@linaro.org>
Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate DT code in preparation for follow-on ACPI integration.
Based on code from: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When too many remotes are bound to an FDB entry, index may not be increased.
This problem will be caused on the large scale environment that is based on
the unicast default destination, for instance.
Signed-off-by: Atzm Watanabe <atzm@iij.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device tree support is disabled, the fifo_pin is uninitialized,
this patch will set the fifo_pin value based on platform data
Signed-off-by: Yong Li <sdliyong@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use '%zx' to print size_t format in order to fix the following build warning:
drivers/net/ethernet/mellanox/mlxsw/item.h:65:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type 'size_t' [-Wformat=]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev() fails we are not propagating the error and
we return success because ax_open() succeeded previously.
Fix this by checking the return value of ax_open() and
register_netdev() and propagate the error in case of failure.
Reported-by: RUC_Soft_Sec <zy900702@163.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.
Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.
This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error flows its possible to free an SKB even if it was not allocated.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some tabs so that statements line up correctly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were missing curly braces so it means we call add_debugfs_mem()
unintentionally.
Fixes: 3ccc6cf74d ('cxgb4: Adds support for T6 adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register definitions #defines for accessing the EEPROM.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates a large chunk of temporary buffer using kzalloc
to copy FW image. As there is no real need of this memory to be
physically contiguous, use vzalloc instead.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it is required to capture minidump for iSCSI functions
as part of default minidump collection process. To enable this, firmware
exports it's capability and driver need to enable that capability
by issuing a mailbox command.
With this feature, firmware can provide additional iSCSI function's
minidump with smaller minidump capture mask (0x1f).
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include local headers files after kernel's header files.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the Marvel 88e1111 PHY only two SGMII modes are available, both
allowing only SGMII to copper mode (with or without clock). SGMII
to fiber mode is not supported. Make sure the fiber/copper registers
selector bits are cleared for selecting copper mode.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make ath_opmode_to_string return "OCB" for NL80211_IFTYPE_OCB. Currently
it will return "UNKNOWN".
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Add a spinlock which will ensure that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Since rx path is run in driver tasklet,
tx status cannot be reported directly from interrupt context
(there would be no way to lock it out).
Add tasklet for tx and move all possible code from irq handler
there.
Note: tx tasklet is needed because workqueue is queued very
rarely and that kills TCP performance.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx is run inside a tasklet so ieee80211_rx() should be used
instead of ieee80211_rx_ni().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DMA to variables located on the stack is a bad idea.
For simplicity and to avoid frequent allocations create
a buffer inside the device structure. Protect this
buffer with vendor_req_mutex. Don't protect vendor
requests which don't use this buffer.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.
In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.
If the vif is a p2p mgmt vif, block some mac80211 ops.
Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.
Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.
Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add definitions and function prototypes for generic_cfg
command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for long intervals on sched scan.
If configured, the original request interval will
be used num_short_interval times, and then the
long interval will be used.
While on it, fix the scan command field names
to reflect the expected value is in ms (rather
than secs).
These values will be taken from the conf file,
so bump its version accordingly.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added support for a new time sync event
the event data contains the WiLink TSF value.
To trigger the event, a HW modification is required,
so as a supporting firmware binary.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit d8d2f19feb ("mwifiex: silence TDLS link delete failure
for nonexistent link") lowers the priority of error message when
TDLS link is already deleted. But it had got increased by
commit acebe8c10a ("mwifiex: change dbg print func to
mwifiex_dbg")
Reported-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch changes the state change behaviour of at86rf230 to always
TX_ARET mode. According the at86rf2xx datasheets TX_ARET mode doesn't
mean to be always waiting for ack frames after transmit. The transceiver
will automatically wait for ack frames or not if the acknowledge request
bit is set. See section "TX_ARET_ON – Transmit with Automatic Frame
Retransmission and CSMA-CA Retry".
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commit "e29aa33 bna: Enable Multi Buffer RX" moved packets counter
increment from the beginning of the NAPI processing loop after the check
for erroneous packets so they are never accounted. This counter is used
to inform firmware about number of processed completions (packets).
As these packets are never acked the firmware fires IRQs for them again
and again.
Fixes: e29aa33 ("bna: Enable Multi Buffer RX")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PP2 controller is capable of per-CPU TX processing, which means there are
per-CPU banked register sets and queues. Current version of the driver supports
TX packet coalescing - once on given CPU sent packets amount reaches a threshold
value, an IRQ occurs. However, there is a single interrupt line responsible for
CPU0/1 TX and RX events (the latter is not per-CPU, the hardware does not
support RSS).
When the top-half executes the interrupt cause is not known. This is why in
NAPI poll function, along with RX processing, IRQ cause register on both
CPU's is accessed in order to determine on which of them the TX coalescing
threshold might have been reached. Thus the egress processing and releasing the
buffers is able to take place on the corresponding CPU. Hitherto approach lead
to an illegal usage of on_each_cpu function in softirq context.
The problem is solved by resigning from TX coalescing interrupts and separating
egress finalization from NAPI processing. For that purpose a method of using
hrtimer is introduced. In main transmit function (mvpp2_tx) buffers are released
once a software coalescing threshold is reached. In case not all the data is
processed a timer is set on this CPU - in its interrupt context a tasklet is
scheduled in which all queues are processed. At once only one timer per-CPU can
be running, which is controlled by a dedicated flag.
This commit removes TX processing from NAPI polling function, disables hardware
coalescing and enables hrtimer with tasklet, using new per-CPU port structure
(mvpp2_port_pcpu).
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp2 driver allows usage of per-CPU TX processing. Once the packets are
prepared independetly on each CPU, the hardware enqueues the descriptors in
common TX queue. After they are sent, the buffers and associated sk_buffs
should be released on the corresponding CPU.
This is why a special index is maintained in order to point to the right data to
be released after transmission takes place. Each per-CPU TX queue comprise an
array of sent sk_buffs, freed in mvpp2_txq_bufs_free function. However, the
index was used there also for obtaining a descriptor (and therefore a buffer to
be DMA-unmapped) from common TX queue, which was wrong, because it was not
referring to the current CPU.
This commit enables proper unmapping of sent data buffers by indexing them in
per-CPU queues using a dedicated array for keeping their physical addresses.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using spinlocks protection during one-time driver initialization is not
necessary. Moreover it resulted in invalid GFP_KERNEL allocation under the lock.
This commit removes redundant spinlocks from buffer manager part of mvpp2
initialization.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reported-by: Alexandre Fournier <alexandre.fournier@wisp-e.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use the length of the transmitted skb (which was freed), but
that of the response skb.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.
Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCS of incoming packets is already checked by HW. Just strip it out.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves compile errors on um-allyesconfig.
Note that there are many other drivers which have the same issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
System ports are unique identifiers in a multi-ASIC environment that
represent all the available ports in the system. Local ports on the
other hand, are unique only within the local ASIC.
Since system port to local port mapping is not part of the HW-SW
contract and since only single-ASIC configurations are currently
supported, set an explicit 1:1 mapping by configuring the Switch System
Port Record (SSPR) register.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a port's netdevice we should also free the memory
allocated by alloc_etherdev(). Do this by calling free_netdev() at the
end of the teardown sequence.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a low level function for the ATU Load operation, and provide FDB add
and delete wrappers functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a low level _mv88e6xxx_atu_getnext function and helpers
to rewrite the mv88e6xxx_port_fdb_getnext operation.
A mv88e6xxx_atu_entry structure is added for convenient access to the
hardware, and GLOBAL_ATU_FID is defined instead of the raw 0x01 value.
The previous implementation did not handle the eventual trunk mapping.
If the related bit is set, then the ATU data register would contain the
trunk ID, and not the port vector.
Check this in the FDB getnext operation and do not handle it (yet).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the __mv88e6xxx_{read,write}_addr functions to more explicit
_mv88e6xxx_atu_mac_{read,write} functions, which also respect the single
underscore convention used in the file (meaning SMI lock must be held).
In the meantime, define their MAC address parameters as an array of
ETH_ALEN bytes instead of a char pointer.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently manages one FID per port (or bridge group), with a
mask of DSA_MAX_PORTS bits, where 0 means that the FID is in use.
The Marvell 88E6xxx switches support up to 4094 FIDs (from 1 to 0xfff;
FID 0 means that multiple address databases are not being used).
This patch changes the fid_mask for an fid_bitmap of 4096 bits.
>From now on, FIDs 1 to num_ports are reserved for non-bridged ports and
bridge groups (a bridge group gets the FID of its first member). The
remaining bits will be reserved for VLAN entries.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the fdb_{add,del,getnext} function pointer in favor of new
port_fdb_{add,del,getnext}.
Implement the switchdev_port_obj_{add,del,dump} functions in DSA to
support the SWITCHDEV_OBJ_PORT_FDB objects.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address in the switchdev_obj_fdb structure is currently represented
as a pointer. Replacing it for a 6-byte array allows switchdev to carry
addresses directly read from hardware registers, not stored by the
switch chip driver (as in Rocker).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ntb_netdev is allowing the link to come up even when -ENOMEM is returned
from ntb_transport_rx_enqueue. Fix to cover all possible errors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
It was possible for a synchronous update of the RX index in the error
case to get ahead of the asynchronous RX index update in the normal
case. Change the RX processing to preserve an RX completion order.
There were two error cases. First, if a buffer is not present to
receive data, there would be no queue entry to preserve the RX
completion order. Instead of dropping the RX frame, leave the RX frame
in the ring. Schedule RX processing when RX entries are enqueued, in
case there are RX frames waiting in the ring to be received.
Second, if a buffer is too small to receive data, drop the frame in the
ring, mark the RX entry as done, and indicate the error in the RX entry
length. Check for a negative length in the receive callback in
ntb_netdev, and count occurrences as rx_length_errors.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
failed to configure the page size for architectures with page size
different than 4K.
Fixes: 938fe83 ("net/mlx5_core: New device capabilities handling")
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are paths in the driver such as an unrecoverable error (UE) detection
followed by a driver unload wherein be_clear() is invoked twice.
Individual data structures are reset so that they are not cleaned/freed
twice. This patch does the same for eqo->affinity_mask. It is freed only
if EQs haven't yet been destroyed. This fixes a possible crash when
affinity_mask is freed twice.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An RX stall issue was seen on Lancer adapters, when RXQs are destroyed
while they are in an "out of buffer" state. This patch fixes this issue
by posting 64 buffers to each RXQ before destroying them in the close path.
This is done after ensuring that no more new packets are selected for
transfer to the RXQs by disabling interface filters.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW issues were observed on Lancer adapters if IFACE filters
(flags, mac addrs etc) are enabled *before* creating RXQs. This patch
changes the driver design by enabling filters in be_open() --
instead of be_setup() -- after RXQs are created and buffers posted.
Two new wrapper functions, be_enable_if_filters() and
be_disable_if_filters() are introduced to enable/disable IFACE filters in
be_open()/be_close() respectively. In be_setup() the IFACE is now created
only with the RSS flag.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_VXLAN_FLOWBASED is useless without IFLA_VXLAN_COLLECT_METADATA,
so combine them into single IFLA_VXLAN_COLLECT_METADATA flag.
'flowbased' doesn't convey real meaning of the vxlan tunnel mode.
This mode can be used by routing, tc+bpf and ovs.
Only ovs is strictly flow based, so 'collect metadata' is a better
name for this tunnel mode.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild bot reported that commit 592fa228f2 ("ath9k: remove struct
ath_atx_ac") broke the build when CONFIG_ATH9K_STATION_STATISTICS is y.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 592fa228f2 ("ath9k: remove struct ath_atx_ac")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-08-05
This series contains updates to i40e, i40evf and e1000e.
Anjali adds support for x772 devices to i40e and i40evf. With the added
support, x772 supports offloading of the outer UDP transmit and receive
checksum for tunneled packets. Also supports evicting ATR filters in the
hardware, so update the driver with this new feature set.
Raanan provides several fixes for e1000e, first rectifies the Energy
Efficient Ethernet in Sx code so that it only applies to parts that
actually support EEE in Sx. Fix whitespace and moved ICH8 related define
to the proper context. Fixed the ASPM locking which was reported by
Bjorn Helgaas. Fix a workaround implementation for systime which could
experience a large non-linear increment of the systime value when
checking for overflow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio declares support for NETIF_F_FRAGLIST, but assumes
that there are at most MAX_SKB_FRAGS + 2 fragments which isn't
always true with a fraglist.
A longer fraglist in the skb will make the call to skb_to_sgvec overflow
the sg array, leading to memory corruption.
Drop NETIF_F_FRAGLIST so we only get what we can handle.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch b1c17215d718: "stmmac: add ipq806x glue layer", leads to the
following static checker warning:
.../stmmac/dwmac-ipq806x.c:314 ipq806x_gmac_probe()
warn: double left shift '1 << (1 << gmac->id)'
The NSS_COMMON_CLK_SRC_CTRL_OFFSET macro is used once as an offset, and
once as a mask, which is a bug indeed. We'll fix it by defining the
offset as the real offset value and computing the mask from it when
required.
Tested on IPQ806x ref designs AP148 & DB149.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, rx buffer size for each rx queue
of an interface is configurable through dts bindings.
But for an interface, the first rx queue's rx buffer
size is always the usual MTU size (plus usual overhead)
and page size for the remaining rx queues (if they are
enabled by specifying a non-zero rx queue depth dts
binding of the corresponding interface). This patch
removes the rx buffer size configuration capability.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As well as for kernels built only for ThunderX ARCH_THUNDERX is also enabled
for kernels which support multiple platforms (such as distro kernels). Thus
"default ARCH_THUNDER" is inappropriate.
I believe default m is equally frowned upon, so remove the line completely
rather than "default m if ARCH_THUNDER".
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Derek Chickles <derek.chickles@caviumnetworks.com>
Cc: Satanand Burla <satananda.burla@caviumnetworks.com>
Cc: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Cc: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Enforcing this flag in RxConfig for the mentioned chips fixes netdev
watchdog issues prepended with AMD IOMMU message(s) like:
AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x001d address=0x0000000000003000 flags=0x0050]
Note that this flag is also set in Realtek's own driver for these chips.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Alexander Lindqvist <alexander@bitspace.se>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* a fix for the stuck TFD queue mechanism - it was producing
noisy false alarms
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running
rsi:
* fix firmware load DMA regression
b43:
* fix extpa_gain check for 2GHz
rtlwifi:
* fix NULL dereference when PCI driver used as an AP
* add missing module parameter declaration for rtl8723be_mod_params.msi_support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVwOsmAAoJEG4XJFUm622bWSAIAJDlW0ZKnxI+tmsbU2CYuoQS
yfiK+oTuQE5+eB+5bNaJqSI2QSzVo11JBxnf4014wu+/gjKy2OHQ48ufXbkFfHB2
t2o+rIx7WL5zvoy67fIifgIQSdg542e68xPc8Wz6MV58szuYscBT78dy2ZWvthqB
S6DK8K+ohHzHYMV5fw65xkcmsXB8BEKEoUckm8ZxjsLF4Pj+ZzAgpqf+i85JYkFM
LwktfKRxg2un9u51IhBCPZUUxe7MhLgZbSuHSP/7ltxWIGctseMAFMlCMrmi9+2B
zXPR+2EMWLy0rgmQ04/sG6LjNdW6tmF1rCtcuKnS7hiOngubAj3UEj9d5r98/LI=
=SqUX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* a fix for the stuck TFD queue mechanism - it was producing
noisy false alarms
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running
rsi:
* fix firmware load DMA regression
b43:
* fix extpa_gain check for 2GHz
rtlwifi:
* fix NULL dereference when PCI driver used as an AP
* add missing module parameter declaration for rtl8723be_mod_params.msi_support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Waking the dealloc thread before decrementing inflight_packets is racy
because it means the thread may go to sleep before inflight_packets is
decremented. If kthread_stop() has already been called, the dealloc
thread may wait forever with nothing to wake it. Instead, wake the
thread only after decrementing inflight_packets.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that TIRs, TISs and flow tables are kept alive while the netdev is
stopped (after executing ndo_stop()) we can do the following
improvements:
- Obsolete the active_vlans SW shadow.
- Do not delete/add flow table rules upon ndo_stop/open.
In addition to simplifying the flow, this change also fastens
the ndo_open/close operations.
- Obsolete synchronization of threads accessing the flow tables
with the netdev stop/open threads.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not make sense to allow events while the netdev is
unregistered.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename some functions that used to be invoked upon ndo_open/stop and
are now invoked upon create/destroy_netdev() in order to better hint
their place in the flow.
Change some functions location in the file so that functions involved
in ndo_open/stop flow will not be interleaved with other functions.
This is a cosmetic change, no logical change here.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX traffic routed to this RQ will be silently dropped, at the NIC HW
level.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally an RX packet flows through the following objects:
Flow table --> TIR --> RQT --> RQ
Where:
- TIR stands for "Transport Interface Receive", defining the RSS and
LRO paramaters.
- RQT stands for "RQ Table", implementing the RSS indirection table.
- RQ stands for "Receive Queue"
For flows that do not need LRO, nor RSS, the driver made a shortcut to
the above RX flow by pointing to the RQ directly from the TIR, yielding
this flow:
Flow table --> TIR --> RQ
In this commit we remove this shortcut by "inserting" a single-RQ RQT
between the TIR and the RQ, i.e RX packets will reach the same RQ but
will go through an RQT of size 1, pointing to just a single RQ.
This way the RX traffic re-direction to/from the "Drop RQ" will be more
uniform (AKA "one flow"), as it will involve only RQTs re-direction and
no TIRs re-direction.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]
[1] http://patchwork.ozlabs.org/patch/492741/
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 230d00eb4b ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful register_netdev, we can use netdev_err rather the more
generic dev_err.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set port to NULL if port probe fails so we don't try to remove partially
initialized port on port probe err cleanup path.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.
Fix this by initializing the refcount to be coherent with the initial
device status.
Fixes:
8fff755e9f (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9MX3
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-04' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
For PCIe/USB chipsets, preallocated skb buffers are reused for
event handling. mwifiex_check_uap_capabilties() performs
skb_pull(). This patch adds missing skb_push() to restore skb's
data pointer/length.
This bug was introduced by commit debfc60081 ("mwifiex: update
AP WMM settings from BSS_START event")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add option to dynamically configure the fw
which debug traces to open
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preallocated event SKBs are getting reused for PCIe chipset.
Their physical addresses are shared with firmware so that
firmware can write data into them.
This patch makes sure that SKB is cleared and length is set to
default while submitting it to firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System crash was observed if one of the driver initialisation
commands is timed out. The reason is our timeout handler triggers
firmware dump, meanwhile driver initialisation error paths have
already freed the adapter structure.
Firmware hasn't yet completely initialized. So collecting firmware
dump is not needed in this case. Command timeout handler is
modified in this patch to fix the crash issue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When WLAN interface is up and running, driver unload and
load was causing command timeout error.
We enable Rx data by updating RX ring read pointer in
init_fw_port(). It should be done when FW is completely
intialialised. Command timeout is fixed in this patch by
moving init_fw_port() call to mwifiex_init_fw_complete().
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable pos is u8 here, so memcpy is needed to store u16 aid.
At the same time, aid should be platform independent, upper layer
utility(wpa_supplicant,etc.,) parse it as le16, so keep it le16
here.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC.
This patch changes the code to track active station TIDs in the txq directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setup rxfiler correctly for offchannel ctx.
This fix problem we didn't configure rxfilter, next
didn't receive probe requests and next failed
p2p_find. This was seen when ath9k loaded with
use_chanctx=1
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While mac80211 setup this per HW, set same
rxfilter configuration for all chanctx.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise p2p device support when ath9k loaded with
use_chanctx=1.
This will fix problem, when first interface is an AP
and next we would like to run p2p_find.
Before p2p find (scan phase) failed with EOPNOTSUPP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
600f5d909a54("mwifiex: cleanup ioctl wait queue and abstraction layer")
introduced the wakeup_interruptible suppression in mwifiex_complete_cmd
b1a47aa5e1e1("mwifiex: fix system hang issue in cmd timeout error case")
then added wakup_interruptible to mwifiex_cmd_timeout_func the single
place setting a status of ETIMEDOUT.
Instead of doing extra work, using the standard call-chain will have the
same effect:
mwifiex_cancel_pending_ioctl
-> mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd
-> wake_up_interruptible
The difference is that previously the condition was not set to true,
but that's probably just an oversight in b1a47aa5e1 and shouldn't
have any consequence
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CMD_F_CANCELED was used to abort mwifiex_process_cmdresp in
case it already started or starts processing the cmd.
But this was probably not working the way intended:
- it is racy: mwifiex_process_cmdresp might already have passed that
test and is continuing to use the cmd node being recycled
- mwifiex_process_cmdresp repeatedly uses adapter->curr_cmd which
we just set to NULL
- mwifiex_recycle_cmd_node will clear the flag
The reason why it probably works is that mwifiex_cancel_pending_ioctl
is only called from mwifiex_cmd_timeout_func, where the there is little
chance of a command response still arriving
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_cancel_pending_ioctl is called only from
mwifiex_cmd_timeout_func. There the wait_q status is set to
-ETIMEDWAIT before calling this function. Whether we reset the status
to -1 or leave it at -ETIMEDWAIT at end doesn't matter since both
are != 0 hence mean failure
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
standard call chain when releasing a cmd node:
mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd, if wait_q_enabled
calling mwifiex_complete_cmd explicitly and setting
wait_q_enabled = false is redundant
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 1fb654fd97ff("mmc: sdio: add reset callback to bus operations"),
sdio cards can be power cycled using mmc_hw_reset.
The use mmc_remove_host/mmc_add_host is discouraged, because these are
internal functions to the mmc core and should only be used by mmc hosts
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Boot loader versions as backward compatible,
starting from v1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Boot loader reports error starting from the struct v2.
Print error info before reset (power up state) in debug mode,
and print same info as error if target reset timed out.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for the system suspend/resume.
In preparation for the run-time PM, implementation made
run-time PM friendly: common for system and run-time PM
code factored out as generic functions, albeit is_runtime
parameter value is always false currently.
For debug purposes, "PM" debug category introduced.
Policy: AP-like interface can't be suspended; otherwise
suspend is allowed. Hardware brought down if interface
was up. Connection, if existed, get lost.
Interface will be brought up upon resume if it was up
before suspend.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow network stack part of Rx processing to run on separate core,
relaxing CPU utilization on the core used for Rx NAPI.
If RXHASH feature is enabled, the driver sets rxhash of each skb to 1
to enable RPS. The core for processing the rx skb is determined by RPS
mechanism according to rx_cpus bit mask which is configured at user level.
For processing skbs on different core from the core which processes
the interrupts, it is recommended not to enable core 0 in rx_cpus bit mask.
Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".
Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the recent kernel versions, multiple MSI is not well supported.
In particular, it is not supported on x86 and ARM architectures.
Also, internal interrupt handling logic is simpler and
more effective when using single interrupt.
Remove support for 3 MSI, convert module parameter
"use_msi" from int with range [0,1,3] to boolean.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx drops may be for 2 reasons: frame is old,
or it is duplicate. On the debugfs "stations" entry,
provide counters per reorder buffer for total
frames processed, drops for these 2 reasons.
Also add debug print for dropped frames.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When printing error message, provide string describing IE kind.
Derive it from IE type
This allows removing of error messages printing
in callers
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
sort overall IE's handling
prepare code (disabled for now) to add IEs for the beacon
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW is allowed to generate WMI events that are not handled by this driver.
Treat such case as warning instead of error.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check event length;
hex dump both Rx and Tx frames
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver report supported TSO (v4 & v6) and IP checksum offload
in addition to previously supported features. In data path
skbs are checked for non-zero gso_size, and when detected sent
to additional function for processing TSO SKBs. Since HW does not
fully support TSO, additional effort is required from the driver.
Driver partitions the data into mss sized descriptors which are
then DMAed to the HW.
Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading with debug_fw flag, do not bail out on
unknown chipId
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use function wil_fw_error_recovery() instead of inline equivalent code
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Multiple del_station requests may be sent to the driver by the
supplicant when turning down AP. This may overflow mailbox
between the FW and ucode
Wait till disconnect of one STA completed before sending next command.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
linux/device.h should be included using <>, not ""
since it is not local include
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the debugfs, there is "ulong" attribute printing.
It is used for bitmap printing, and more appropriate format
would be hexadecimal, not decimal.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When performing Rx reordering, count skb's dropped
per reorder buffer; and print dropped packets count
on the "stations" debugfs entry
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are 2 versions of boot loader struct: v0 and v1.
In the v1, boot loader build version added; as well as
RF status.
Support both versions.
Boot loader structure v1 has RF status; ignore RF error if firmware
not going to be loaded; driver can still be used to interact with the HW
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Replace spaces with tab.
2) Move ich8lan related define to the proper context.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 does NVM update via the adminq queue, so we need to add support for
that.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports evicting ATR filters in the HW. With this patch, we enable
the feature in the driver and avoid filter deletion by the driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports IWARP, this patch handles checking for PE critical errors.
Since the driver doesn't support the IWARP interface for now, this patch
just does bare minimum to log a message oif a PE critical error
happens.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the i40e and i40evf register.h file with the registers for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the firmware API update to support the new X722 device.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add capabilities flags specific to X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding device ids for new hardware X722
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When building a Tx Command for management frames, we are lacking
a check for action frames, for which we should set a different
pm_timeout. This cause the fw to stay awake for 100TU after each
such frame is transmitted, resulting an excessive power consumption.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.
In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.
When the device is slave on the bus(SDIO) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. When the FW wants load / unload pages, it creates an
interrupt, and the driver uploads / downloads the page to an address in
the a specific address on the device's memory.
The driver can support up to 1 MB of pages.
Add paging mechanism for the UMAC on SDIO in order to allow the program to
use a larger virtual space while using less physical memory on the device
itself.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As a preperation for multiple RX queues change the RBD
allocation model.
The new model includes a background allocator. The allocator is
called by the interrupt handler when there are two released
buffers by the queue, and the allocator starts allocating eight
pages per request.
When the queue has released 8 pages it tries claiming the
request. If the pages are not ready - it keeps claiming.
This new model should make sure that RBDs are always available
across the multiple queues.
The RBDs are transferred between the allocator and the queue.
The queue moves the free RBDs upon freeing them to the allocator.
The allocator moves them back to the queue's possession when the
request is claimed.
The allocator has an initial pool to make sure there are always RBDs
available for the request completion.
Release of the buffers at exit is done per pools - the allocator
frees its own initial pool and the queue frees its own pool.
Existing code refactor -
-Queue's initial pool is the size of the queue only as the allocation
of the new buffers no longer uses this pool.
-Removal of replenish background work, and replenish calls in the
interrupt handler and restock().
-The replenish() and the rxq used_list are used only during
initialization.
-Moved page allocation to a new function for code reuse.
New code -
Allocator code - new structure and functions.
Interrupt handler uses the allocator functions for replenishing buffers.
Reuse of the restock() method.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change the FW debug trigger tlv to include a monitor only
option. Setting this option to true will cause fw dump triggers
to only collect monitor data and skip other dumps such as
SMEM, SRAM, CSR, PRPH, etc.
This option is used when accessing the different parts of the
firmware memory is not wanted and can cause unwanted behavior
like when debugging TX latency.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow frag SKBs in PCIe and advertise the maximum number of frags
to the opmode. As a fallback. linearize the SKB if it exceeds the
maximum number of fragments. This allows using the hardware better
(filling more TBs) and should improve performance when used by the
opmode.
Also adjust tracing to be able to deal with this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Gscan is a scan feature which is supported on certain devices only,
hence the need for a TLV flag for it. For devices that support gscan
store the gscan capabilities advertised by the FW so the driver can
report it to upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set max TX aggregation size for 8260 SDIO devices series to 40 frames.
Fine tune max RX aggregation size - change it to 21.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our firmware scheduler used to suffer from false wake-up on 500 time units.
We had to came up with a formula to address this buggy behavior.
Now that our firmware is fixed, we can go back to our old policy.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for dumping all the RBs in the RX queue
when FW error occurs.
This will assist debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Print the CPU1 and CPU2 secured boot status registers from the NIC
to indicate a SYSASSERT during secured engine unlocking process
on init/protocol image.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
chunfan chen