Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In qed_ll2_start_ooo() the ll2_info variable is uninitialized and then
passed to qed_ll2_acquire_connection() where it is copied into a new
memory space.
This shouldn't cause any issue as long as non of the copied memory is
every read.
But the potential for a bug being introduced by reading this memory
is real.
Detected by CoverityScan, CID#1399632 ("Uninitialized scalar variable")
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't save TIPC header values before the header has been validated,
from Jon Paul Maloy.
2) Fix memory leak in RDS, from Zhu Yanjun.
3) We miss to initialize the UID in the flow key in some paths, from
Julian Anastasov.
4) Fix latent TOS masking bug in the routing cache removal from years
ago, also from Julian.
5) We forget to set the sockaddr port in sctp_copy_local_addr_list(),
fix from Xin Long.
6) Missing module ref count drop in packet scheduler actions, from
Roman Mashak.
7) Fix RCU annotations in rht_bucket_nested, from Herbert Xu.
8) Fix use after free which happens because L2TP's ipv4 support returns
non-zero values from it's backlog_rcv function which ipv4 interprets
as protocol values. Fix from Paul Hüber.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
qed: Don't use attention PTT for configuring BW
qed: Fix race with multiple VFs
l2tp: avoid use-after-free caused by l2tp_ip_backlog_recv
xfrm: provide correct dst in xfrm_neigh_lookup
rhashtable: Fix RCU dereference annotation in rht_bucket_nested
rhashtable: Fix use before NULL check in bucket_table_free
net sched actions: do not overwrite status of action creation.
rxrpc: Kernel calls get stuck in recvmsg
net sched actions: decrement module reference count after table flush.
lib: Allow compile-testing of parman
ipv6: check sk sk_type and protocol early in ip_mroute_set/getsockopt
sctp: set sin_port for addr param when checking duplicate address
net/mlx4_en: fix overflow in mlx4_en_init_timestamp()
netfilter: nft_set_bitmap: incorrect bitmap size
net: s2io: fix typo argumnet argument
net: vxge: fix typo argumnet argument
netfilter: nf_ct_expect: Change __nf_ct_expect_check() return value.
ipv4: mask tos for input route
ipv4: add missing initialization for flowi4_uid
lib: fix spelling mistake: "actualy" -> "actually"
...
Fix typos and add the following to the scripts/spelling.txt:
partiton||partition
Link: http://lkml.kernel.org/r/1481573103-11329-7-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 653d2ffd6405 ("qed*: Fix link indication race") introduced another
race - one of the inner functions called from the link-change flow is
explicitly using the slowpath context dedicated PTT instead of gaining
that PTT from the caller. Since this flow can now be called from
a different context as well, we're in risk of the PTT breaking.
Fixes: 653d2ffd6405 ("qed*: Fix link indication race")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF syncronizes all IOV activity relating to its VFs
by using a single workqueue handling the work.
The workqueue would reach a bitmask of pending VF events
and act upon each in turn.
Problem is that the indication of a VF message [which sets
the 'vf event' bit for that VF] arrives and is set in
the slowpath attention context, which isn't syncronized with
the processing of the events.
When multiple VFs are present, it's possible that PF would
lose the indication of one of the VF's pending evens, leading
that VF to later timeout.
Instead of adding locks/barriers, simply move from a bitmask
into a per-VF indication inside that VF entry in the PF database.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare bin_attribute structures as const as they are only passed as an
arguments to the functions device_remove_bin_file and
device_create_bin_file. These function arguments are of type const, so
bin_attribute structures having this property can be made const too.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct bin_attribute i@p = {...};
@ok1@
identifier r1.i;
position p,p1;
@@
(
device_remove_bin_file(...,&i@p)
|
device_create_bin_file(..., &i@p1)
)
@bad@
position p!={r1.p,ok1.p,ok1.p1};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct bin_attribute i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare bin_attribute structures as const as they are only passed as an
arguments to the functions device_remove_bin_file and
device_create_bin_file. These function arguments are of type const, so
bin_attribute structures having this property can be made const too.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct bin_attribute i@p = {...};
@ok1@
identifier r1.i;
position p,p1;
@@
(
device_remove_bin_file(...,&i@p)
|
device_create_bin_file(..., &i@p1)
)
@bad@
position p!={r1.p,ok1.p,ok1.p1};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct bin_attribute i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.
This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.
Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flows accessing registers require the flow to hold a PTT entry.
To protect 'major' load/unload flows a main_ptt is pre-allocated
to guarantee such flows wouldn't be blocked by PTT being
unavailable.
Status block initialization currently uses the main_ptt which
is incorrect, as this flow might run concurrently to others
[E.g., loading qedr while toggling qede]. That would have dire
effects as it means registers' access to device breaks and further
read/writes might access incorrect addresses.
Instead, when initializing status blocks acquire/release a PTT
as part of the flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently utilizes the same loop variable in two
nested loops.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF learns of the current link state via its bulletin board,
which might reflect either the physical link state or some
user-configured logical state.
Whenever the physical link changes or whnever such a configuration
is explicitly made by user the PF driver would update the bulletin
that the VF reads. But if neither has happened - i.e., PF still
hasn't got a physical link up and no additional configuration was
done the VF wouldn't have a valid link information available.
Simply reflect the physical link state whenever the VF is
initialized. The user could then affect it however he wants.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed needs to be informed of the removal of the qede interface
prior to its actual removal, as qede has some registered callbacks
that might get called async to the removal flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to make sure the slowpath workqueue and the qede lock
are ready for the registration of the netdevice, as once
registered there's no guarantee those wouldn't be used.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserving doorbell BAR space according to the currently active CPUs
may result in a bug if disabled CPUs are later enabled but no
doorbell space was reserved for them.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If QP is in reset state then there are no resources to free so avoid
freeing any.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the state is read only after the buffers are relesed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CQ resource pool is protected by a spin lock. When a CQ creation
fails it now deallocates under that lock as well.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'dma_alloc_coherent()' fails, we should release resources allocated so
far, just as done in all other cases in this function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the FCoE driver (qedf) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver support for,
- Registering the ptp clock functionality with the OS.
- Timestamping the Rx/Tx PTP packets.
- Ethtool callbacks related to PTP.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds the required qed interfaces for configuring/reading
the PTP clock on the adapter.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
# ./perf record -a -e bpf:* sleep 10
# ./perf script
sock_example 6197 [005] 283.980322: bpf:bpf_map_create: map type=ARRAY ufd=4 key=4 val=8 max=256 flags=0
sock_example 6197 [005] 283.980721: bpf:bpf_prog_load: prog=a5ea8fa30ea6849c type=SOCKET_FILTER ufd=5
sock_example 6197 [005] 283.988423: bpf:bpf_prog_get_type: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
sock_example 6197 [005] 283.988443: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[06 00 00 00] val=[00 00 00 00 00 00 00 00]
[...]
sock_example 6197 [005] 288.990868: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[01 00 00 00] val=[14 00 00 00 00 00 00 00]
swapper 0 [005] 289.338243: bpf:bpf_prog_put_rcu: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
[1] https://lwn.net/Articles/705270/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct qed_ll2_info is rather large, so putting it on the stack
can cause an overflow, as this warning tries to tell us:
drivers/net/ethernet/qlogic/qed/qed_ll2.c: In function 'qed_ll2_start':
drivers/net/ethernet/qlogic/qed/qed_ll2.c:2159:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
qed_ll2_start_ooo() already uses a dynamic allocation for the structure
to work around that problem, and we could do the same in qed_ll2_start()
as well as qed_roce_ll2_start(), but since the structure is only
used to pass a couple of initialization values here, it seems nicer
to replace it with a different structure.
Lacking any idea for better naming, I'm adding 'struct qed_ll2_conn',
which now contains all the initialization data, and this now simply
gets copied into struct qed_ll2_info rather than assigning all members
one by one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero. Also, it makes the code clearer
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qedr isn't part of the kernel then don't allocate RDMA resources
for it in qed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently multicast traffic wouldn't be routed internally to
listener; Instead it would only be sent to network via the
physical carrier.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trusted VFs would be allowed to receive promiscuous and
multicast promiscuous data.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver receives a recognized encapsulated packet it needs
to set the skb->encapsulation field as well.
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds