TPS65217 MFD is an interrupt controller and MFD slave devices like
tps65217-charger and tps65217-pwrbutton request an interrupt to handle
each HW event.
Currently, TPS65217 IRQ name is not defined, so the result is as below.
root@arm:~# cat /proc/interrupts
...
182: 0 INTC 7 Level tps65217-irq
183: 0 - 1 Edge tps65217-charger
185: 0 - 2 Edge tps65217_pwrbutton
This patch specifies the name of the interrupt controller.
182: 0 INTC 7 Level tps65217-irq
183: 0 tps65217 1 Edge tps65217-charger
185: 0 tps65217 2 Edge tps65217_pwrbutton
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
palmas_dev and palmas_power_off are always assigned together.
So the check for palmas_dev inside palmas_power_off function
is redundant. Removing the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As DCVDD will often be supplied by a child node of the MFD, we
can't call mfd_remove_devices as the first step in arizona_dev_exit
as might be expected (tidy up the children before we tidy up the
MFD). We need to disable and put the DCVDD regulator before we call
mfd_remove_devices, to prevent PM runtime from turning this back on we
also need to disable the PM runtime before we do this. Finally we can
not clean up the IRQs until all the MFD children have been removed, as
they may have registered IRQs themselves.
This creates a window of time where the interrupts are enabled but
the PM runtime, on which the IRQ handler depends, is not available,
any interrupts in this window will go unhandled and fill the log with
failed to resume device messages. To avoid this we simply disable the
main IRQ at the start of arizona_dev_exit, we don't need to actually
handle any IRQs in this window as we are removing the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support to PM8821 PMIC and interrupt support.
PM8821 is companion device that supplements primary PMIC PM8921 IC.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enable MWI mechanism if PCI bus master supports it.
It might be potential benefit in some cases. Documentation [1] says that
standard Memory Write might supply more current data than in the CPU modified
cache line and "trashing a line in the cache may trash some data that is more
current that in the memory line". This allows to avoid potential retries and
other performance degradation issues on the bus.
[1] PCI System Architecture, 4th edition, ISBN: 0-201-30974-2, pp.117-119.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4/DCDC5
+ LDO7-10
+ Slightly different output voltage/currents
+ 32kHz Output
+ RTC
+ USB Charger detection
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 supports either master/standalone or slave mode.
Slave mode allows sharing the serial bus, even with multiple
AXP806 which all have the same hardware address.
This is done with extra "serial interface address extension",
or AXP806_BUS_ADDR_EXT, and "register address extension", or
AXP806_REG_ADDR_EXT, registers. The former is read-only, with
1 bit customizable at the factory, and 1 bit depending on the
state of an external pin. The latter is writable. Only when
the these device addressing bits (in the upper 4 bits of the
registers) match, will the device respond to operations on
its other registers.
Add these 2 registers to the regmap so we can access them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a typo in MODULE_DEVICE_TABLE(). 'pmic_acpi_ids' should be
'bxtwc_acpi_ids'.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba9963 ("mfd: add platform_device sharing support for mfd")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'i2c_new_dummy()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The new sun4i mfd driver is lacking a dependency, triggering very rarely
int randconfig kernel builds:
drivers/mfd/sun4i-gpadc.o: In function `sun4i_gpadc_probe':
sun4i-gpadc.c:(.text.sun4i_gpadc_probe+0x110): undefined reference to `devm_regmap_add_irq_chip'
This adds a 'select REGMAP_IRQ', as the other drivers with this problem do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config ABX500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We replace module.h with init.h and export.h -- the latter since the file
does make use of EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_GPADC
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 GPADC driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_DEBUG
drivers/mfd/Kconfig: bool "Enable debug info via debugfs"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We replace module.h with moduleparam.h ; the latter since this file
was implicitly relying on getting it.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB3100_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only. In doing
so, the debugfs unregister fcn becomes unused so we remove it too.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial spelling mistake fixes in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
No need to use irq_create_mapping (although there is no issue with
doing so) when we are only looking up an existing mapping. Just to
streamline things a little and make the code a little more clear
change some calls from irq_create_mapping to irq_find_mapping.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The kernel WARNs and then crashes today if wm8994_device_init() fails
after calling devm_regulator_bulk_get().
That happens because there are multiple devices involved here and the
order in which managed resources are freed isn't correct.
The regulators are added as children of wm8994->dev. Whereas,
devm_regulator_bulk_get() receives wm8994->dev as the device, though it
gets the same regulators which were added as children of wm8994->dev
earlier.
During failures, the children are removed first and the core eventually
calls regulator_unregister() for them. As regulator_put() was never done
for them (opposite of devm_regulator_bulk_get()), the kernel WARNs at
WARN_ON(rdev->open_count);
And eventually it crashes from debugfs_remove_recursive().
Fix the kernel warnings and crashes by using regulator_bulk_get()
instead of devm_regulator_bulk_get() and explicitly freeing the supplies
in exit paths.
Tested on Exynos 5250, dual core ARM A15 machine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mach/hardware.h is needed on C source code side, not header.
And struct davinci_vc is duplicated definition.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the trailing spaces on the register default lines to
stop checkpatch complaining.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building for X86 using COMPILE_TEST we get this warning:
../drivers/mfd/sun4i-gpadc.c: In function ‘sun4i_gpadc_probe’:
../drivers/mfd/sun4i-gpadc.c:110:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Since an integer and a pointer are difference sizes on 64bit architectures.
Convert to case to a long instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The i2c subsys does not load modules by compatible, only by
i2c-id, with e.g. a modalias of: "i2c:axp209".
Populate the axp20x_i2c_id[] table with supported ids, so that
module auto-loading will work.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap devicetree binding documentation states that a native-endian
property should be supported as well as big-endian & little-endian,
however syscon in its duplication of the parsing of these properties
omits support for native-endian. Fix this by setting
REGMAP_ENDIAN_NATIVE when a native-endian property is found.
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that
only DEV_OFF_RST can power off supplies. RK818 has been fixed this
issue, so that DEV_OFF is used to power off supplies.
Signed-off-by: Jianhong Chen <chenjh@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mfd/fsl-imx25-tsadc.ko | grep alias
alias: platform:mx25-tsadc
After this patch:
$ modinfo drivers/mfd/fsl-imx25-tsadc.ko | grep alias
alias: platform:mx25-tsadc
alias: of:N*T*Cfsl,imx25-tsadcC*
alias: of:N*T*Cfsl,imx25-tsadc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mfd/hi655x-pmic.ko | grep alias
After this patch:
$ modinfo drivers/mfd/hi655x-pmic.ko | grep alias
alias: of:N*T*Chisilicon,hi655x-pmicC*
alias: of:N*T*Chisilicon,hi655x-pmic
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver only has runtime but no build time dependency with ARCH_U300 ||
ARCH_U8500 So it can be built for testing purposes if COMPILE_TEST option
is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver is meant for Exynos systems so do not offer the option
elsewhere unless build-testing.
Cc: Inha Song <ideal.song@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building with extra warnings enabled, most files including
linux/mfd/tps65912.h warn about a static variable defined in the
header:
include/linux/mfd/tps65912.h:331:35: warning: 'tps65912_regmap_config' defined but not used [-Wunused-const-variable=]
We also duplicate the data structure between the i2c and spi front-end
drivers. Moving it into the driver code avoids the warning and
the duplication.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The order in which resources were freed in wm8994_device_exit() isn't
correct. The regulators are removed before they are disabled.
Fix it by reordering code a bit, which makes it exact opposite of
wm8994_device_init() as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These can fit in a single line (80 columns), don't split lines
unnecessarily.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The OF is not a strict build-time dependency so max77620 and max77686
can be compile tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the correct function name in one case and adjust a variable name to
that of the corresponding function parameter in another case.
Issue detected using Coccinelle (http://coccinelle.lip6.fr/)
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. For now, only the ADC and the thermal
sensor drivers are probed by the MFD, the touchscreen controller support
will be added later.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The kernel WARNs and then crashes today if wm8994_device_init() fails
after calling devm_regulator_bulk_get().
That happens because there are multiple devices involved here and the
order in which managed resources are freed isn't correct.
The regulators are added as children of wm8994->dev. Whereas,
devm_regulator_bulk_get() receives wm8994->dev as the device, though it
gets the same regulators which were added as children of wm8994->dev
earlier.
During failures, the children are removed first and the core eventually
calls regulator_unregister() for them. As regulator_put() was never done
for them (opposite of devm_regulator_bulk_get()), the kernel WARNs at
WARN_ON(rdev->open_count);
And eventually it crashes from debugfs_remove_recursive().
--------x------------------x----------------
wm8994 3-001a: Device is not a WM8994, ID is 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /mnt/ssd/all/work/repos/devel/linux/drivers/regulator/core.c:4072 regulator_unregister+0xc8/0xd0
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.8.0-rc6-00154-g54fe84cbd50b #41
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c010e24c>] (unwind_backtrace) from [<c010af38>] (show_stack+0x10/0x14)
[<c010af38>] (show_stack) from [<c032a1c4>] (dump_stack+0x88/0x9c)
[<c032a1c4>] (dump_stack) from [<c011a98c>] (__warn+0xe8/0x100)
[<c011a98c>] (__warn) from [<c011aa54>] (warn_slowpath_null+0x20/0x28)
[<c011aa54>] (warn_slowpath_null) from [<c0384a0c>] (regulator_unregister+0xc8/0xd0)
[<c0384a0c>] (regulator_unregister) from [<c0406434>] (release_nodes+0x16c/0x1dc)
[<c0406434>] (release_nodes) from [<c04039c4>] (__device_release_driver+0x8c/0x110)
[<c04039c4>] (__device_release_driver) from [<c0403a64>] (device_release_driver+0x1c/0x28)
[<c0403a64>] (device_release_driver) from [<c0402b24>] (bus_remove_device+0xd8/0x104)
[<c0402b24>] (bus_remove_device) from [<c03ffcd8>] (device_del+0x10c/0x218)
[<c03ffcd8>] (device_del) from [<c0404e4c>] (platform_device_del+0x1c/0x88)
[<c0404e4c>] (platform_device_del) from [<c0404ec4>] (platform_device_unregister+0xc/0x20)
[<c0404ec4>] (platform_device_unregister) from [<c0428bc0>] (mfd_remove_devices_fn+0x5c/0x64)
[<c0428bc0>] (mfd_remove_devices_fn) from [<c03ff9d8>] (device_for_each_child_reverse+0x4c/0x78)
[<c03ff9d8>] (device_for_each_child_reverse) from [<c04288c4>] (mfd_remove_devices+0x20/0x30)
[<c04288c4>] (mfd_remove_devices) from [<c042758c>] (wm8994_device_init+0x2ac/0x7f0)
[<c042758c>] (wm8994_device_init) from [<c04f14a8>] (i2c_device_probe+0x178/0x1fc)
[<c04f14a8>] (i2c_device_probe) from [<c04036fc>] (driver_probe_device+0x214/0x2c0)
[<c04036fc>] (driver_probe_device) from [<c0403854>] (__driver_attach+0xac/0xb0)
[<c0403854>] (__driver_attach) from [<c0401a74>] (bus_for_each_dev+0x68/0x9c)
[<c0401a74>] (bus_for_each_dev) from [<c0402cf0>] (bus_add_driver+0x1a0/0x218)
[<c0402cf0>] (bus_add_driver) from [<c040406c>] (driver_register+0x78/0xf8)
[<c040406c>] (driver_register) from [<c04f20a0>] (i2c_register_driver+0x34/0x84)
[<c04f20a0>] (i2c_register_driver) from [<c01017d0>] (do_one_initcall+0x40/0x170)
[<c01017d0>] (do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
[<c0a00dbc>] (kernel_init_freeable) from [<c06e07b0>] (kernel_init+0x8/0x114)
[<c06e07b0>] (kernel_init) from [<c0107978>] (ret_from_fork+0x14/0x3c)
---[ end trace 0919d3d0bc998260 ]---
[snip..]
Unable to handle kernel NULL pointer dereference at virtual address 00000078
pgd = c0004000
[00000078] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.8.0-rc6-00154-g54fe84cbd50b #41
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
task: ee874000 task.stack: ee878000
PC is at down_write+0x14/0x54
LR is at debugfs_remove_recursive+0x30/0x150
[snip..]
[<c06e489c>] (down_write) from [<c02e9954>] (debugfs_remove_recursive+0x30/0x150)
[<c02e9954>] (debugfs_remove_recursive) from [<c0382b78>] (_regulator_put+0x24/0xac)
[<c0382b78>] (_regulator_put) from [<c0382c1c>] (regulator_put+0x1c/0x2c)
[<c0382c1c>] (regulator_put) from [<c0406434>] (release_nodes+0x16c/0x1dc)
[<c0406434>] (release_nodes) from [<c04035d4>] (driver_probe_device+0xec/0x2c0)
[<c04035d4>] (driver_probe_device) from [<c0403854>] (__driver_attach+0xac/0xb0)
[<c0403854>] (__driver_attach) from [<c0401a74>] (bus_for_each_dev+0x68/0x9c)
[<c0401a74>] (bus_for_each_dev) from [<c0402cf0>] (bus_add_driver+0x1a0/0x218)
[<c0402cf0>] (bus_add_driver) from [<c040406c>] (driver_register+0x78/0xf8)
[<c040406c>] (driver_register) from [<c04f20a0>] (i2c_register_driver+0x34/0x84)
[<c04f20a0>] (i2c_register_driver) from [<c01017d0>] (do_one_initcall+0x40/0x170)
[<c01017d0>] (do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
[<c0a00dbc>] (kernel_init_freeable) from [<c06e07b0>] (kernel_init+0x8/0x114)
[<c06e07b0>] (kernel_init) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Code: e1a04000 f590f000 e3a03001 e34f3fff (e1902f9f)
---[ end trace 0919d3d0bc998262 ]---
--------x------------------x----------------
Fix the kernel warnings and crashes by using regulator_bulk_get()
instead of devm_regulator_bulk_get() and explicitly freeing the supplies
in exit paths.
Tested on Exynos 5250, dual core ARM A15 machine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The order in which resources were freed in wm8994_device_exit() isn't
correct. The regulators are removed before they are disabled.
Fix it by reordering code a bit, which makes it exact opposite of
wm8994_device_init() as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap devicetree binding documentation states that a native-endian
property should be supported as well as big-endian & little-endian,
however syscon in its duplication of the parsing of these properties
omits support for native-endian. Fix this by setting
REGMAP_ENDIAN_NATIVE when a native-endian property is found.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This register is used in the AIF code but is missing from the register
tables.
Signed-off-by: Praveen Kumar Vegivada <praveen.vegivada@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AXP22x has also some different register map than axp20x, they're also
added here.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig and file naming for the PM8xxx driver is totally
confusing:
- Kconfig options MFD_PM8XXX and MFD_PM8921_CORE, some in-kernel
users depending on or selecting either at random.
- A driver file named pm8921-core.c even if it is indeed
used by the whole PM8xxx family of chips.
- An irqchip named pm8xxx since it was (I guess) realized that
the driver was generic for all pm8xxx PMICs.
As I may want to add support for PM8901 this is starting to get
really messy. Fix this situation by:
- Remove the MFD_PM8921_CORE symbol and rely solely on MFD_PM8XXX
and convert all users, including LEDs Kconfig and ARM defconfigs
for qcom and multi_v7 to use that single symbol.
- Renaming the driver to qcom-pm8xxx.c to fit along the two
other qcom* prefixed drivers.
- Rename functions withing the driver from 8921 to 8xxx to
indicate it is generic.
- Just drop the =m config from the pxa_defconfig, I have no clue
why it is even there, it is not a Qualcomm platform. (Possibly
older Kconfig noise from saveconfig.)
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As part of an effort to rid the mostly unused second parameter for I2C
related .probe() functions and to conform to other existing frameworks
we're moving over to a temporary replacement .probe() call-back.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba9963 ("mfd: add platform_device sharing support for mfd")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit c4dd1ba355
("mfd: stmpe: Add reset support for all STMPE variant")
we're resetting the STMPE expanders before use.
This caused a regression on the STMP2401 on the Nomadik
NHK8815:
stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x43 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x44 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
It turns out that we start to poll for the reset bit to
go low again too quickly: the STMPE2401 is not yet online and
ready to be asked for the status of the RESET bit.
By introducing a 10ms delay before starting to hammer
the register for information, we get back to normal:
stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
Cc: stable@vger.kernel.org
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Fixes: c4dd1ba355 ("mfd: stmpe: Add reset support for all STMPE variant")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The wcove USB Type-C driver is currently being flooded with
interrupts that are not targeted to it. The reason for that
is because all CHRG first level interrupts are mapped to it.
This fixes the issue by introducing separate irq for the
usbc device, and mapping only USB Type-C PHY interrupts to
it.
Fixes: 9c6235c863 ("mfd: intel_soc_pmic_bxtwc: Add bxt_wcove_usbc device")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 41a3da2b8e ("mfd: intel-lpss: Save register context on
suspend") saved the register context while going to suspend and
also put the device in reset state.
Due to the resetting of device, system cannot enter S3/S0ix
states when no_console_suspend flag is enabled. The system
and serial console both hang. The resetting of device is not
needed while going to suspend. Hence remove this code.
Cc: stable@vger.kernel.org
Fixes: 41a3da2b8e ("mfd: intel-lpss: Save register context on suspend")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are a few issues on Intel Kaby Lake PCH-H properties added by
commit a6a576b78e09 ("mfd: lpss: Add Intel Kaby Lake PCH-H PCI IDs"):
- Input clock of I2C controller on Intel Kaby Lake PCH-H is 120 MHz not
133 MHz. This was probably copy-paste error from Intel Broxton I2C
properties.
- There is no default I2C SDA hold time specified which is used when
ACPI doesn't provide it. I got information from Windows driver team
that Kaby Lake PCH-H can use the same configuration than Intel
Sunrisepoint PCH.
- Common HS-UART properties are not used.
Fix these by reusing the Sunrisepoint properties on Kaby Lake PCH-H.
Fixes: a6a576b78e09 ("mfd: lpss: Add Intel Kaby Lake PCH-H PCI IDs")
Reported-by: Xiang A Wang <xiang.a.wang@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
store the physical address of the device in its priv to use it
for DMA addressing in the client drivers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mfd_add_devices enables parsing device tree nodes without compatibles
for regulators and gpio modules. Replace of_platform_populate with
mfd_add_devices. mfd_cell currently is populated with regulators,
gpio and powerbutton.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently read directly calls the repmap read function. Hence
remove the redundant wrapper and use regmap read wherever
needed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
This is an extremely quiet release for the regulator API, we've got a
small set of bug fixes and minor feature enhancements for drivers plus a
couple of more visible changes:
- Add support for ramp times in regulators that don't use selectors.
- New driver for LTC3676.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX83uoExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9AI
Vgf/TKsgLY/UGdEhgmuSCWDI+64e8NjHRADRYR3rpgg8gfa5LeB6M+Zha6FnEWxn
FAj93OAcszNZqHz8ZLZcyV2j9rXhhRlPI1FadAe+0FTQgqN0EKREsL4MHgJNz8C5
mHe/87t8u+4xvscK7JjyvmmMk2UlvvmH8mmaAHTSa3QiX/Jc2isok6NFI370hDRq
DlmgqKU9plZU7hqtvseNFcgiQ1iaFXI6B0Fv6O87czzVvokHdt5BKugKq4LhwInH
A2H6MXap0H2f8GSmFBtXCSonnTKOKYkAUnbEC1LUASCTxPAIEMVMTdO3jV05wI8g
vsy/95OrfLvzKgrE/UlQlV1WZg==
=bca4
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This is an extremely quiet release for the regulator API, we've got a
small set of bug fixes and minor feature enhancements for drivers plus
a couple of more visible changes:
- add support for ramp times in regulators that don't use selectors.
- new driver for LTC3676"
* tag 'regulator-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: dbx500: remove unused functions in dbx500-prcmu.c
regulator: pv88080: Update regulator for PV88080 BB silicon support
regulator: core: don't return error with inadequate reason
regulator: tps65910: Work around silicon erratum SWCZ010
regulator: core: Add set_voltage_time op
regulator: core: Don't skip set_voltage_time when ramp delay disabled
regulator: core: Simplify error flow in _regulator_do_set_voltage()
regulator: core: Use local ops variable in _regulator_do_set_voltage()
regulator: hi6421: mark hi6421_regulator_ldo_get_optimum_mode() static
regulator: Kconfig: Fix typo
regulator: bindings: Use the correct symbol for second
regulator: Remove support for optional supplies in the bulk API
regulator: Add LTC3676 support
regulator: rk808: Delete owner assignment
regulator: tps65218: do not disable DCDC3 during poweroff on broken PMICs
mfd: tps65218: add version check to the PMIC probe
The Arizona CODECs will generally function correctly without a reset line
although it is strongly advised to have one, as such we do allow the system
to boot if the reset gpio is missing or incorrectly specified. However
we should fail probe if we get a probe deferral request, this patch adds
handling for this case.
Reported-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This function is only used in a single place and no new users will be
added as all the devices other required GPIOs are already handled. As
such just merge the code back into the calling function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
This patch adds DT settings for the max_channels_clocked, spk_fmt and
spk_mute pdata.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The McPDM in OMAP4/5 is using the pdmclk from twl6040 as functional clock.
The twl6040-pdmclk driver provides a clock which can be used to make sure
that the pdmclk is active when the McPDM is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Due to the lack of parity in the way array fields have been named/
numbered, a mistake was made where more debug fields were declared
than actually existed. In doing so, 2 fields were added, which
although unclear, were already declared in the array. The result
was that the latter declarations trashed the former ones.
This patch places the array back in the correct order and removes
the offending NULL entries.
While we're at it, let's ensure this doesn't happen again by naming
each field properly and add a new *_LAST define to describe how
many fields there should be.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The tps65217 gained a new warning when building with W=1:
drivers/mfd/tps65217.c:85:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
This fixes it by putting the 'inline' modifier before 'const'.
Fixes: 262d5cc6ceb2 ("mfd: tps65217: Add support for IRQs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
readl_poll_timeout() calls usleep_range(), but
regmap_atmel_hlcdc_reg_write() is called in atomic context (regmap
spinlock held).
Replace the readl_poll_timeout() call by readl_poll_timeout_atomic().
Cc: <stable@vger.kernel.org>
Fixes: ea31c0cf9b ("mfd: atmel-hlcdc: Implement config synchronization")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The newly added exynos lpass driver produces a build warning when
CONFIG_PM is disabled since the only callers of exynos_lpass_disable
are under an #ifdef:
drivers/mfd/exynos-lpass.c:93:13: error: 'exynos_lpass_disable' defined but not used [-Werror=unused-function]
static void exynos_lpass_disable(struct exynos_lpass *lpass)
This removes the #ifdef and replaces it with __maybe_unused annotations
so the compiler can leave out the unused code silently with less
room for mistakes.
Fixes: 36c26760bba8 ("mfd: Add Samsung Exynos Low Power Audio Subsystem driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Default I2C device properties for Intel Broxton, especially SDA hold time
may not be enough on Intel Apollo Lake. These properties are used in case
we don't get timing parameters from ACPI.
The default SDA hold time for Broxton may fail with arbitration lost errors
on Apollo Lake:
i2c_designware i2c_designware.1: i2c_dw_handle_tx_abort: lost arbitration
Fix this by using different default device properties on Apollo Lake than
Broxton.
Reported-by: Paul Liu <paul.liu@canonical.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=156181
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config TWL4030_CORE
drivers/mfd/Kconfig: bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove what modular code that we can, so that when reading the
driver there is less doubt that it is builtin-only. Note that we can't
remove the twl_remove() itself ; it is still used by the probe unwind
routine. So we leave it linked into the .remove as well, even though
it will most likely never be called via that path from an unbind.
Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_SUN6I_PRCM
drivers/mfd/Kconfig: bool "Allwinner A31 PRCM controller"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_SMSC
drivers/mfd/Kconfig: bool "SMSC ECE1099 series chips"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We replace module.h with init.h and delete an unused moduleparam.h
include.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_INTEL_MSIC
drivers/mfd/Kconfig: bool "Intel MSIC
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple instances of module references, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_AS3722
drivers/mfd/Kconfig: bool "ams AS3722 Power Management IC"
...meaning that it currently is not being built as a module by anyone.
In response to an earlier patch set suggesting removal of the unused
modular code, Laxman suggested that this driver be instead moved to
tristate.
We do that here, and confirm it can build and modpost as a tristate.
However there remains to be runtime testing in order to ensure this
change is 100% functional for "=m".
Cc: Florian Lobmaier <florian.lobmaier@ams.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_ALTERA_A10SR
drivers/mfd/Kconfig: bool "Altera Arria10 DevKit System Resource chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since builtin_driver() uses the same init level priority as
module_spi_driver() the init ordering remains unchanged with
this commit. [Note that there is no builtin_spi_driver macro,
so we open-code what it would be via builtin_driver().]
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add tps65217 power buttor subdevice with assigned IRQ resources.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for handling IRQs: power button, AC and USB power state
changes. Mask and interrupt bits are shared within one register, which
prevents us to use regmap_irq implementation. New irq_domain is created in
order to add interrupt handling for each tps65217's subsystem. IRQ
resources have been added for charger subsystem to be able to notify about
AC and USB state changes.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
probe_irq_off() returns '0' on failure, not NO_IRQ, so the check
in this driver is clearly wrong. This replaces it with the
regular '!irq' check used in other drivers.
The sa1100 platform that this driver is used on originally numbered
all its interrupts starting at '0', which would have conflicted with
this change, but as of commit 18f3aec ("ARM: 8230/1: sa1100: shift
IRQs by one"), this is not a problem any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bulk access is not working with twl6040, we need to use single register
access. Bulk access would happen when we try to sync the regcache after
power on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As runtime PM doesn't function whilst processing system suspend/resume
operations and the Arizona IRQ handlers need runtime PM to function
we must disable IRQs during these operations. Whilst this is
already done in the driver we are using suspend/suspend_late and
resume/resume_noirq to do so which has two problems. Firstly, as
suspend_late is before suspend_noirq that means we still have a
small window where an IRQ can cause issues. Secondly, if another
suspend_late handler fails after ours has run then (as resume_noirq
will not run) we will make unbalanced calls to enable_irq.
This is all simply fixed by using the suspend_noirq callback rather
than suspend_late. Whilst we are doing this tidy the code up a little,
and use the appropriate helper macros.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To regard the act8945a-charger as a sub-device, add .of_compatible for
act8945a-charger cell.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are some cases in arizona_dev_init, such as where we don't
recognise the chip ID, in which we head to the error path without
setting a sensible error code in ret. This would lead to the chip
silently failing probe, as it would still return 0. Fix this up by
adding appropriate sets of the return value.
Whilst adding these update the existing paths that do return an error
when the chip is not recognised to use ENODEV, which seems like a better
fit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds common driver for the Top block of the Samsung Exynos
SoC Low Power Audio Subsystem. This is a minimal driver which prepares
resources for IP blocks like I2S, audio DMA and UART and exposes
a regmap for the Top block registers. Also system power ops are added
to ensure the Audio Subsystem is operational after system suspend/resume
cycle.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function da9052_clear_fault_log() is added to mitigate the case of
persistent data being transferred between reboots.
Clearance of any the persistent information within the DA9053 FAULT_LOG
register must be completed during start-up so the fault-log does not
continue with previous values. A clearance function has been added here in
the kernel driver because wiping the fault-log cannot be counted on outside
the Linux kernel.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Adam Thomson <adam.thomson.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adjust jump targets according to the Linux coding style convention.
Another check for the variable "status" can be omitted then at the end.
Link: https://lkml.kernel.org/g/<20160628163146.GG29166@dell>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Member "status" of struct usb_sg_request is managed by usb core. A
spin lock is used to serialize the change of it. The driver could
check the value of req->status, but should avoid changing it without
the hold of the spinlock. Otherwise, it could cause race or error
in usb core.
This patch could be backported to stable kernels with version later
than v3.14.
Cc: stable@vger.kernel.org # 3.14+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
probe_irq_on() only returns non-zero if it found any interrupts below
IRQ32 which could be probe candidates. If all the probable interrupts
are higher than 32, then this will cause a failure. Fix this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MSM8660, APQ8060, IPQ806x and MSM8960 have a GCC clock
to the message RAM used by the RPM. This needs to be enabled
for messages to pass through. This is a crude solution that
simply prepare/enable at probe() and disable/unprepare
at remove(). More elaborate PM is probably possible to
add later.
The construction uses IS_ERR() to gracefully handle the
platforms that do not provide a message RAM clock. It will
bail out of probe only if the clock is hitting a probe
deferral situation.
Of course this requires the proper device tree set-up:
rpm: rpm@104000 {
compatible = "qcom,rpm-msm8660";
clocks = <&gcc RPM_MSG_RAM_H_CLK>;
clock-names = "ram";
...
};
I have provided this in the MSM8660 device tree, and will
provide patches for the other targets.
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Intel Whiskey Cove PMIC includes several function units, e.g.
ADC, thermal, USB Type-C, GPIO, etc. The corresponding device has
to be created in the mfd driver(intel_soc_pmic_bxtwc.c). This change
adds the USB Type-c device.
Signed-off-by: Bin Gao <bin.gao@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Kaby Lake PCH-H has the same LPSS than Intel Sunrisepoint. Add the new
IDs to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's only used in this driver and never get modified, make it static const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes a compile failure:
drivers/built-in.o: In function `wm8350_i2c_probe':
core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c'
Makefile:953: recipe for target 'vmlinux' failed
Fixes: 52b461b86a ("mfd: Add regmap cache support for wm8350")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove incorrect e-mail addresses from the copyright header and
MODULE_AUTHOR() macro. These e-mail addresses are no longer in use.
The author names have not been changed, only the e-mail addresses have
been deleted from the source files.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that we have a GPIO driver for the AXP209, we can add it to our MFD.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds requesting of the clocks supplied on MCLK1, MCLK2 pins,
gating of the 32k clock is added to the arizona_clk32k_enable(),
arizona_clk32k_disable() helpers.
It's a temporary change until the CODEC's clock controller gets exposed
through the clk API and is helpful for board configurations where the
MCLK clocks are not provided by always on oscillators.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ACPI WDAT table is the preferred way to use hardware watchdog over the
native iTCO_wdt. Windows only uses this table for its hardware watchdog
implementation so we should be relatively safe to trust it has been
validated by OEMs
Prevent iTCO watchdog creation if we detect that there is ACPI WDAT table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The HTC GPIO driver is a pure GPIO driver and I just can not
see what it is doing inside MFD. Let's just move it to GPIO
and take this opportunity to move the platform data to
<linux/platform_data/gpio-htc-egpio.h>
Cc: arm@kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.
This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.
This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clocking
- Battery support
Both RK808 and RK818 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The LP873X chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators.
- Configurable General Purpose Output Signals (GPO).
PMIC interacts with the main processor through i2c. PMIC has
couple of LDOs (Linear Regulators), couple of BUCKs (Step-Down DC-DC
Converter Cores) and GPOs (General Purpose Output Signals).
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer revisions of the ChromeOS EC add more events besides the keyboard
ones. So handle interrupts in the MFD driver and let consumers register
for notifications for the events they might care.
To keep backward compatibility, if the EC doesn't support MKBP event, we
fall back to the old MKBP key matrix host command.
Cc: Randall Spangler <rspangler@chromium.org>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Vic Yang <victoryang@google.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to support the Qualcomm MDM9615 SoC, add support for the
RPM regulator entries in the qcom-rpm driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to support the Qualcomm MDM9615 PMIC, add support for the
pm8018 in pm8921 MFD driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Version information will be needed to handle some error cases under the
regulator driver, so store the information once during MFD probe.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
STMPE1600 is a 16-bit port expander.
Datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
this update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to prepare the ground to STMPE1600,
as STMPE1600's SYS_CTRL register has the same layout as
STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI
bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reset was only implemented for STMPE1801 variant despite
all variant have a SOFT_RESET bit.
For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7
of SYS_CTRL register.
For STMPE610/811 (which have the same variant id) SOFT_RESET
bit is bit 1 of SYS_CTRL register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As STMPE1801/1601/24xx has a SYS_CTRL register and
STMPE1601/2403 has even a SYS_CTRL2 register, add
STMPE_IDX_SYS_CTRL/2 and update driver code accordingly
This update prepares the ground for not yet supported STMPE1600
which share similar REG_SYS_CTRL register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AC100 is a multifunction device with an audio codec subsystem and
an RTC subsystem. These two subsystems share a common register space
and host interface.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
- New API to call bespoke pre/post IRQ handlers; Regmap
- New Device Support
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
- New Functionality
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
- Fix-ups
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
- Bug Fixes
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KB2d
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- New API to call bespoke pre/post IRQ handlers; Regmap
New Device Support:
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
New Functionality:
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
Fix-ups:
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
Bug Fixes:
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic"
* tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (42 commits)
mfd: qcom_rpm: Parametrize also ack selector size
mfd: twl6040: Handle mclk used for HPPLL and optional internal clock source
mfd: Add support for COMe-cSL6 and COMe-mAL10 to Kontron PLD driver
mfd: hi655x: Fix return value check in hi655x_pmic_probe()
mfd: smsc-ece1099: Return directly after a function failure in smsc_i2c_probe()
mfd: smsc-ece1099: Delete an unnecessary variable initialisation in smsc_i2c_probe()
mfd: dm355evm_msp: Return directly after a failed platform_device_alloc() in add_child()
mfd: twl-core: Refactoring for add_numbered_child()
mfd: twl-core: Return directly after a failed platform_device_alloc() in add_numbered_child()
mfd: arizona: Add missing disable of PM runtime on probe error path
mfd: stmpe: Move platform data into MFD driver
mfd: max14577: Allow driver to be built as a module
mfd: max14577: Use module_init() instead of subsys_initcall()
mfd: arizona: Remove some duplicate defines
mfd: qcom_rpm: Remove unused define
mfd: hi655x-pmic: Add powerkey device to hi655x PMIC driver
mfd: hi655x-pmic: Rename some interrupt macro names
mfd: hi655x-pmic: Fixup issue with un-acked interrupts
mfd: arizona: Check if AOD interrupts are pending before dispatching
mfd: qcom_rpm: Fix offset error for msm8660
...
Except for the constant DB8500_PRCMU_FW_VERSION_OFFSET number, nothing
is ever passed through the platform data and used in a driver, so we
can simply stop passing it around.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When configuring FPS during probe, assuming a DT node is present for
FPS, the code can run into a problem with the switch statements in
max77620_config_fps() and max77620_get_fps_period_reg_value(). Namely,
in the case of chip->chip_id == MAX77620, it will set
fps_[mix|max]_period but then fall through to the default switch case
and return -EINVAL. Returning this from max77620_config_fps() will
cause probe to fail.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RPM has two sets of selectors (IPC bit fields): request and
acknowledge. Apparently, some models use 4*32 bit words for select
and some use 7*32 bit words for request, but all use 7*32 words
for acknowledge bits.
So apparently you can on the models with requests of 4*32 select
bits send 4*32 messages and get 7*32 different replies, so on ACK
interrupt, 7*32 bit words need to be read. This is how the vendor
code apparently works.
Cc: stable@vger.kernel.org
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On some boards, like omap5-uevm the MCLK is gated by default and in order
to be able to use the High performance modes of twl6040 it need to be
enabled by SW.
Add support for handling the MCLK source clock via CCF.
At the same time lower the print priority of the notification that the 32K
clock is not provided and it is not going to be handled by the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is an unmodified resend of the patch already been sent on
February 17 as it seems to have fallen through the net.
This patch adds the DMI system ID of the Kontron COMe-cSL6 and
COME-mAL10 boards to the Kontron PLD driver. The list of supported
products in the module description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR(). Also remove unneeded error handling of
platform_get_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This issue was detected by using the Coccinelle software.
Return directly if a call of the function "devm_regmap_init_i2c"
or "regmap_write" failed.
Delete the jump label "err" then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The platform_device_put() function was called in one case by the
add_child() function during error handling even if the passed
variable "pdev" contained a null pointer.
Return directly in this case.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adjust jump targets according to the Linux coding style convention.
Another check for the variable "status" can be omitted then at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The platform_device_put() function was called in one case by the
add_numbered_child() function during error handling even if the passed
variable "pdev" contained a null pointer.
Return directly in this case.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The STMPE platform data is only populated from the device tree
in all existing users, so push the struct and make the OF case
the norm.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver's Kconfig symbol is a boolean but nothing prevents the driver
to be built as a module instead of built-in. It is true that most system
integrators will choose the latter but the config should not restrict it.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver's init function is called at subsys init call level but the
dependencies provided by the driver are looked up by drivers that have
probe deferral support, so manual ordering of init calls isn't needed.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This define RPM_SIGNAL probably pertains to the IPC signal which
we ended up fetching from the device tree instead. the define is
unused, remove it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Wire up the powerkey driver functionality for the hi655x PMIC.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the hi655x-pmic driver has names for interrupt mask
values, but not for the interrupt numbers themselves.
So to allow for interrupt numbers to have sane names, rename
the mask values with the _MASK postfix and use the existing
names as the interrupt name
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
While trying to get the powerkey to function, I found when
pressing the key, I would get infinitely repeating interrupts.
After digging around a bit, it seems we didn't set the ack_base
value for the regmap irqchip logic, so nothing was acking the
interrupt.
This patch adds the ack_base, which seems to make things work.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Previously the arizona_irq_thread implementation would call
handle_nested_irqs() to handle AOD interrupts without checking if any
were actually pending. The kernel will see these as spurious IRQs and
will eventually disable the IRQ.
This patch ensures we only launch the nested handler if there are AOD
interrupts pending in the codec.
Signed-off-by: Simon Trimmer <simont@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RPM in MSM8660/APQ8060 has different offsets to the selector
ACK and request context ACK registers. Make all these register
offsets part of the per-SoC data and assign the right values.
The bug was found by verifying backwards to the vendor tree in
the out-of-tree files <mach/rpm-[8660|8064|8960]>: all were using
offsets 3,11,15,23 and a select size of 4, except the MSM8660/APQ8060
which was using offsets 3,11,19,27 and a select size of 7.
All other platforms apart from msm8660 were affected by reading
excess registers, since 7 was hardcoded as the number of select
words, this patch makes also this part dynamic so we only write/read
as many select words as the platform actually use.
Symptoms of this bug when using msm8660: the first RPM transaction
would work, but the next would stall or raise an error since the
previous transaction was not properly ACKed as the ACK words were
read at the wrong offset.
Cc: stable@vger.kernel.org
Fixes: 58e214382b ("mfd: qcom-rpm: Driver for the Qualcomm RPM")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap structure pointer is named regmap_tscadc, this is not
consistent with other drivers and is redundant, it also contributes
to several checkpatch warnings involving long lines. Rename this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All functions in this driver reference the same ti_tscadc_dev per device
but use several different names for this structure pointer, this can
be confusing when following the code. Use the name 'tscadc' everywhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The programming guidelines of the MAX77620 for servicing interrupt is:
1. When interrupt occurs from PMIC, mask the PMIC interrupt by
setting GLBLM.
2. Read IRQTOP and service the interrupt.
3. Once all interrupts has been checked and serviced, the interrupt
service routine un-masks the hardware interrupt line by clearing
GLBLM.
Add the pre and post interrupt service handler for mask and unmask the
global interrupt mask bit (for step 1 and 3) as callback from regmap-irq.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the Altera Arria10 Development Kit System Resource
chip which is implemented using a MAX5 as a external gpio extender
with the regmap framework over a SPI bus.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
WARNING: please, no spaces at the start of a line
+ { "tps6507x", 0 },$
WARNING: please, no spaces at the start of a line
+ { }$
Signed-off-by: Ben Copeland <ben.copeland@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
tscadc_readl and tscadc_writel are single line functions and do not save
use anything, remove these.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix the code formatting to use the kernel preferred style
of using the actual variables to determine the size using
the sizeof() operator.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix the warnings about the following functions not being
declared by including omap-usb.h which declares them:
drivers/mfd/omap-usb-tll.c:333:5: warning: symbol 'omap_tll_init' was not declared. Should it be static?
drivers/mfd/omap-usb-tll.c:408:5: warning: symbol 'omap_tll_enable' was not declared. Should it be static?
drivers/mfd/omap-usb-tll.c:442:5: warning: symbol 'omap_tll_disable' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The kernel expects the power_off function to not return, and if it does
it panics. Add a slight delay after the i2c write which turns off power
through the PMIC, to give capacitors etc. some time to drain.
Without this the kernel lives on long enough after the poweroff to
print the following on the serial console on my Mele A1000G quad:
[ 248.583588] reboot: Power down
[ 248.600490] Kernel pa
With the delay the start of printing "Kernel panic" is gone.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These tables are never modified, so declare them as const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig: config MFD_MAX8925
drivers/mfd/Kconfig: bool "Maxim Semiconductor MAX8925 PMIC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_MAX8997
drivers/mfd/Kconfig: bool "Maxim Semiconductor MAX8997/8966 PMIC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
mfd/Kconfig:config MFD_MAX8998
mfd/Kconfig: bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We delete the include of module.h as well as an unused include of
moduleparam.h too.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_MAX77620
drivers/mfd/Kconfig: bool "Maxim Semiconductor MAX77620 and MAX20024 PMIC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_MAX77843
drivers/mfd/Kconfig: bool "Maxim Semiconductor MAX77843 PMIC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp22x pmic has a bunch of volatile registers besides the interrupt
ones, extend axp22x_volatile_ranges with these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the PMIC's repower capability for reboots. Register a restart
handler and use a slightly elevated priority of 192 since the PMIC
has suprior reset capability (causing a system wide reset).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Only register power off if the PMIC is defined as system power
controller (see Documentation/devicetree/bindings/power/
power-controller.txt).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4
+ Slightly different output voltage/currents
+ 32kHz Output
- ADC/Charger capabilities
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PMIC MFD driver to support hisilicon hi665x.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
fix spelling mistake, beetween -> between
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD_VEXPRESS_SYSREG driver selects CLKSRC_MMIO, which in turn
conflicts with ARCH_USES_GETTIMEOFFSET, causing a harmless Kconfig
warning when it is set:
warning: (ARCH_MVEBU && ARCH_DIGICOLOR && ARCH_GEMINI && ARCH_KEYSTONE && ARCH_MOXART && ARCH_MXS && PLAT_SPEAR && ARCH_SUNXI && ARCH_TEGRA && ARCH_U300 && PLAT_ORION && ARCH_CLPS711X && ARCH_EP93XX && ARCH_NETX && ARCH_IXP4XX && ARCH_KS8695 && ARCH_W90X900 && ARCH_PXA && ARCH_SA1100 && ARCH_OMAP1 && ARCH_BCM_IPROC && ARCH_INTEGRATOR_AP && ARCH_OMAP2PLUS && MFD_VEXPRESS_SYSREG) selects CLKSRC_MMIO which has unmet direct dependencies (!ARCH_USES_GETTIMEOFFSET)
This was apparently hidden by the fact that no ARM platform that
still sets ARCH_USES_GETTIMEOFFSET has gpiolib support, and we
already have a dependency on GPIOLIB that I added a while ago.
However, after 296ad4acb8 ("gpio: remove deps on
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB"), any platform can enable
CONFIG_GPIOLIB, and that lets us enable MFD_VEXPRESS_SYSREG
as well.
This adds an explicit dependency on !ARCH_USES_GETTIMEOFFSET
to guarantee that we can enable the CLKSRC_MMIO driver without
getting warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MAX77620/MAX20024 are Power Management IC from the MAXIM.
It supports RTC, multiple GPIOs, multiple DCDC and LDOs,
watchdog, clock etc.
Add MFD drier to provides common support for accessing the
device; additional drivers is developed on respected subsystem
in order to use the functionality of the device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some of the bits in this register can be changed by the codec
so we must mark it volatile.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As a counterpart to the usb power_supply cell, this commit adds an AC
power_supply cell to the axp20x driver.
Still missing are the RTC backup battery and the main battery charger
cells.
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
GPIO lookup tables are supposed to be zero terminated. Let's do that
and avoid accidentally walking off the end.
Cc: stable@vger.kernel.org
Fixes: 61dd2ca2d4 ("mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for adding MFD child devices and
devm_regmap_add_irq_chip() for IRQ chip registration.
This reduces the error code path and .remove callback for removing
MFD child devices and deleting IRQ chip data.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for adding MFD child devices and
devm_regmap_add_irq_chip() for IRQ chip registration.
This reduces the error code path and .remove callback for removing
MFD child devices and deleting IRQ chip data.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for adding MFD child devices and
devm_request_threaded_irq() for IRQ registration.
This reduces the need of remove callback for removing MFD child
devices and unregistering IRQ.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for adding MFD child devices and
devm_regmap_add_irq_chip() for IRQ chip registration.
This reduces the error code path and .remove callback for removing
MFD child devices and deleting IRQ chip data.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for adding MFD child devices and
devm_regmap_add_irq_chip() for IRQ chip registration.
This reduces the error code path and .remove callback for removing
MFD child devices and deleting IRQ chip data.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver's file path in the comment is wrong, so just remove it since
these tends to get out of date and they serve very little purpose.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
SMSC MFD driver does not add any MFD child devices via
mfd_add_devices() and hence it is not required to call
mfd_remove_devices() to remove MFD child devices.
Remove the call of the API mfd_remove_devices() which will
result as remove of .remove callback for driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The clk32k clock is prepared and enabled in twl6040_power() but the clock
is left enabled in case of an error while it should be disable/unprepared.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The clk_prepare_enable() function can fail so check the return
value and propagate the error in case of a failure.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver makes no use of linux/regulator/driver.h which should only
be used by drivers implementing a regulator. Since it's unlikely to
ever need anything from there remove the include.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All configurations are lost and the registers will have
default values when the hardware is suspended and resumed,
so saving the private register space context on suspend, and
restoring it on resume.
Fixes: 4b45efe852 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There was a static checker warning in wm8400_reg_read() because we were
returning u16 and that can't hold the negative error codes. The
function isn't used, so let's just delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since this commit:
commit b9a8a271c3 ("mfd: make mfd_remove_devices() iterate in reverse
order")
The order in which the MFD children remove has been reversed, as our
driver contains some dependencies between the devices we need to make
some changes to ensure the driver unloads cleanly.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some sub driver like RTC module need irq domain from parent to create
irq mapping when driver initialize. so move mt6397_irq_init() before
mfd_add_devices().
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch converts device node to fwnode for dwapb driver, so
as to provide a unified fwnode for DT and ACPI bindings.
Tested-by: Alan Tull <delicious.quinoa@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiang Qiu <qiujiang@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removed the name property from dwapb_port_property.
The name property is redundant, since we can get this info
from dwapb_gpio dev node.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiang Qiu <qiujiang@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are platforms using the ChromeOS embeded controller on ARM64 now,
so let's allow using this driver (without having to use COMPILE_TEST).
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver's init and exit function don't do anything besides adding and
deleting the I2C driver so the module_i2c_driver() macro could be used.
Currently is not being used because the driver is initialized at subsys
initcall level, claiming that this is done to allow consumers devices to
use the resources provided by this driver. But dependencies are in DT so
manual ordering of init calls is not necessary any more.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We're planning to remove the gpiochip_add() function to swith
to gpiochip_add_data() with NULL for data argument.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ben Dooks <ben@fluff.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We're planning to remove the gpiochip_add() function to swith
to gpiochip_add_data() with NULL for data argument.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and remove
the call of mfd_remove_devices() from .remove callback to remove
MFD child-devices. This is done by managed device framework.
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Gyungoh Yoo <jack.yoo@skyworksinc.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and remove
the call of mfd_remove_devices() from .remove callback to remove
MFD child-devices. This is done by managed device framework.
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and remove
the call of mfd_remove_devices() from .remove callback to remove
MFD child-devices. This is done by managed device framework.
CC: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: John Crispin <blogic@openwrt.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Milo Kim <milo.kim@ti.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Matt Porter <mporter@linaro.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for MFD devices registration and get
rid of .remove callback to remove MFD child-devices. This is done
by managed device framework.
CC: Wenyou Yang <wenyou.yang@atmel.com>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add resource managed API devm_mfd_add_devices() for the mfd_add_devices().
This helps in reducing code in error path as it is not required
to call mfd_remove_devices() explicitly to remove all child-devices.
In some cases, it also helps not to implement .remove() callback
which get called during driver unbind.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP809 is a new PMIC that is paired with Allwinner's A80
SoC, along with a slave AXP806 PMIC.
This PMIC is quite similar to the earlier AXP223, though the interrupts
and regulator have changed a bit.
This patch adds support for the interrupts and power button of the PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Avoid a false recursive locking warning from lockdep by adding a lock
class for the arizona IRQ chip.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The consumer of max77693 regulators on Trats2 board (samsung-usb2-phy
driver) supports deferred probing so the max77693 main MFD driver can be
built now as a module. This gives more flexibility and removes manual
ordering of init calls.
Suggested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The structure da9063_irq_data and define EVENTS_BUF_LEN are not used, so
remove the redundant entries.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead to being true/false, the "handled" is true/uninitialized.
Presumably this doesn't cause that many problems in real life because
normally we handle the IRQ.
Fixes: eea6b7cc53 ('mfd: Add lp8788 mfd driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If MDF child devices have separate ACPI nodes identified
by _HID/_CID, they will not be assigned the intended
ACPI companion.
acpi_match_device_ids will return 0 if a the child device
matches the _HID/_CID, so this patch changes the matching
condition to check for 0 on success.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Mika Westerberg <mika.westeberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to pass struct pci_dev * to intel_quark_register_i2c_clk() and
intel_quark_unregister_i2c_clk(). Change the parameter to struct device *. As a
result store it in the private struct instead of struct pci_dev *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a potential resource leak in case when ->probe() fails. We have to
unregister and remove clock tree which is done here.
This is a follow up to previously pushed commit c4726abce6 ("mfd:
intel_quark_i2c_gpio: Use clkdev_create()") that prevents double free() when
clkdev_drop() followed by kfree() in devm_kcalloc() release stage.
I leave Fixes tag here, but the backporting will require to backport the commit
c4726abce6 ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") first.
Cc: stable@vger.kernel.org
Fixes: 60ae5b9f5c (mfd: intel_quark_i2c_gpio: Add Intel Quark X1000 I2C-GPIO MFD Driver)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mask_events_buf is not used, so remove this redundant array.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since device_add_property_set() now always takes a copy of
the property_set, and also since the fwnode type is always
hard coded to be FWNODE_PDATA, there is no need for the
drivers to deliver the entire struct property_set. The
function can just create the instance of it on its own and
bind the properties from the drivers to it on the spot.
This renames device_add_property_set() to
device_add_properties(). The function now takes struct
property_entry as its parameter instead of struct
property_set.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW6m24AAoJEEEQszewGV1zUasP/RpTrjRcNI5QFHjudd2oioDx
R/IljC06Q072ZqVy/MR7QxwhoU8jUnCgKgv4rgMa1OcfHblxC2R1+YBKOUSij831
E+SYmYDYmoMhN7j5Aslr66MXg1rLdFSdCZWemuyNruAK8bx6cTE1AWS8AELQzzTn
Re/CPpCDbujLy0ZK2wJHgr9ZkdcBGICtDRCrOR3Kyjpwk/DSZcruK1PDN+VQMI3k
bJlwgtGenOHINgCq/16edpwj/hzmoJXhTOZXJHI5XVR6czTwb3SvCYACvCkauI/a
/N7b3quG88b5y0OPQPVxp5+VVl9GyVcv5oGzIfTNat/g5QinShZIT4kVV9r0xu6/
TQHh1HlXleh+QI3yX0oRv9ztHreMf+vdpw1dhIwLqHqfJ7AWdOGk7BbKjwCrsOoq
t/qUVFnyvooLpyr53Z5JY8+LqyynHF68G+jUQyHLgTZ0GCE+z+1jqNl1T501n3kv
3CSlNYxSN/YUBN3cnroAIU/ZWcV4YRdxmOtEWP+7xgcdzTE6s/JHb2fuEfVHzWPf
mHWtJGy8U0IR4VSSEln5RtjhRr0PAjTHeTOGAmivUnaIGDziTowyUVF+X5hwC77E
DGTuLVx/Kniv173DK7xNAsUZNAETBa3fQZTgu+RfOpMiM1FZc7tI1rd7K7PjbyCc
d2M0gcq+d11ITJTxC7OM
=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
I2C host controller need to be configured properly in order to meet I2C
timings specified in the I2C protocol specification. Some Intel Broxton
based machines do not have this information in the ACPI namespace (or the
boot firmware does not support ACPI at all) so we use build-in device
properties instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ipaq-micro driver uses SET_SYSTEM_SLEEP_PM_OPS() to
remove the reference to its resume function, but does
not use an #ifdef around the definition, so we get
a build warning:
drivers/mfd/ipaq-micro.c:379:12: error: 'micro_resume' defined but not used [-Werror=unused-function]
This adds a __maybe_unused annotation so the compiler knows
it can silently drop it instead of warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The max77686 MFD driver supports both the Maxim 77686 and Maxim 77802
PMICs but only the OF device table contains entries for both devices.
The max77802 entry is missing in the I2C device ID table which isn't
a problem currently since the driver only supports DT but it will be
needed if the driver is changed to be built as a module since the I2C
core always reports a I2C modalias uevent so auto-load will not work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the device is registered via OF, the OF table is used to match the
driver instead of the I2C device ID table but the entries in the latter
are used as aliasses to load the module if the driver was not built-in.
This is because the I2C core always reports an I2C module alias instead
of an OF one but that could change so it is better to always export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver's Kconfig symbol is a boolean but nothing prevents the driver
to be built as a module instead of built-in. It is true that most system
integrators will choose the latter but the config should not restrict it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the PWM resources to the STMPE MFD driver, so that
it can properly grab and use them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).
tps65090 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).
as3711 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).
rc5t583 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The platform bus_type .match callback attempts to match the platform device
name with an entry on the .id_table if provided and fallbacks to match with
the driver's name if a table is not provided.
Using a platform device ID to match is more explicit, allows the driver to
support more than one device and also the MODULE_DEVICE_TABLE macro can be
used to export the module aliases information instead of the MODULE_ALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add an updated set of registers listed in the core regmap_range volatile
ranges defined for the DA9063.
These new registers contain bits that cannot be considered under the full
control of software. Under various conditions the hardware will set and/or
automatically clear bit(s) contained in these registers.
When using a cached version of regmap, the volatility of these registers must
be identified otherwise the regmap operations may not ensure the registers
are explicitly altered.
As well as updating the list of volatile registers, this change will fix a
corner case discovered in the DA9063 ONKEY which is used by the DA9063 core.
In the ONKEY case, the CONTROL_B register is now listed as volatile in the
regmap_range because it contains the bit field NONKEY_LOCK. This bit can be
altered by hardware, in which case regmap must be notified of its ability
to be manpiulated outside of software control.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MT6323 has the INT_CON and INT_STATUS located at a different position.
Make the registers locations configurable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add an updated set of registers listed in the core regmap_range volatile
ranges defined for the DA9062.
These new registers contain bits that cannot be considered under the full
control of software. Under various conditions the hardware will set and/or
automatically clear bit(s) contained in these registers.
When using a cached version of regmap, the volatility of these registers must
be identified otherwise the regmap operations may not ensure the registers
are explicitly altered.
As well as updating the list of volatile registers, this change will fix a
corner case discovered in the DA9063 ONKEY which is used by the DA9062 core.
In the ONKEY case, the CONTROL_B register is now listed as volatile in the
regmap_range because it contains the bit field NONKEY_LOCK. This bit can be
altered by hardware, in which case regmap must be notified of its ability
to be manpiulated outside of software control.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for the Active-semi ACT8945A PMIC.
It is a Multi Function Device with the following subdevices:
- Regulator
- Charger
It is interfaced to the host controller using I2C interface,
ACT8945A is a child device of the I2C.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD_ARIZONA_I2C and MFD_ARIZONA_SPI both select MFD_ARIZONA and all
three of those select MFD_CORE, this makes the selects of MFD_CORE in
MFD_ARIZONA_I2C and MFD_ARIZONA_SPI redundant, so we remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The help text had a copy and paste error and refers to I2C in the SPI
section. This patch corrects this typo.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
syscon_regmap_config can be made const if syscon_probe() creates a local
copy on the stack, just like syscon_register() does.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Determine the regmap max_register configuration from the io resource size
and the reg-io-width device tree property.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The prcmu_config_clkout() function ensures that the 'clkout' argument
can only be '0' or '1' using an appropriate BUG_ON(), so the compiler
should know that the div_mask, mask, and bits variables are always
initialized later on. However, it doesn't understand this in gcc-5.2
and produces a false positive warning instead:
drivers/mfd/db8500-prcmu.c: In function 'prcmu_config_clkout':
drivers/mfd/db8500-prcmu.c:762:10: error: 'div_mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (val & div_mask) {
^
drivers/mfd/db8500-prcmu.c:769:13: error: 'mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if ((val & mask & ~div_mask) != bits) {
^
drivers/mfd/db8500-prcmu.c:757:7: error: 'bits' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Replacing the switch() statement with an equivalent if() lets
gcc figure this out reliably and avoids the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the TPS65912 device. It provides communication
through I2C and contains the following components:
- Regulators
- Load switches
- GPO controller
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Core:
- New sysfs interface to set and read clock offset
- Drivers can now be both I2C and SPI (see pcf2127 and ds3232)
New drivers:
- Alphascale ASM9260
- Epson RX6110SA
- Maxim max20024 and max77620 (in max77686)
- Microchip PIC32
- NXP pcf2129 (in pcf2127)
Subsystem wide cleanups:
- remove IRQF_EARLY_RESUME when unecessary
Drivers:
- ds1307: clock output, temperature sensor and wakeup-source support
- ds1685: actually spin forever in poweroff error path
- ds3232: many cleanups
- ds3234: merged in ds3232
- hym8563: fix invalid year calculation
- max77686: many cleanups
- max77802 merged in max77686
- pcf2123: cleanups and offset support
- pcf85063: cleanups
- pcf8523: propely handle oscillator stop bit
- rv3029: many cleanups, trickle charger and temperature sensor support
- rv8803: convert spin_lock to mutex_lock
- rx8025: many fixes
- vr41xx: restore alarm_irq_enable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+x1Q
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Core:
- New sysfs interface to set and read clock offset
- Drivers can now be both I2C and SPI (see pcf2127 and ds3232)
New drivers:
- Alphascale ASM9260
- Epson RX6110SA
- Maxim max20024 and max77620 (in max77686)
- Microchip PIC32
- NXP pcf2129 (in pcf2127)
Subsystem wide cleanups:
- remove IRQF_EARLY_RESUME when unecessary
Drivers:
- ds1307: clock output, temperature sensor and wakeup-source support
- ds1685: actually spin forever in poweroff error path
- ds3232: many cleanups
- ds3234: merged in ds3232
- hym8563: fix invalid year calculation
- max77686: many cleanups
- max77802 merged in max77686
- pcf2123: cleanups and offset support
- pcf85063: cleanups
- pcf8523: propely handle oscillator stop bit
- rv3029: many cleanups, trickle charger and temperature sensor support
- rv8803: convert spin_lock to mutex_lock
- rx8025: many fixes
- vr41xx: restore alarm_irq_enable"
* tag 'rtc-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (86 commits)
rtc: pcf2127: add pcf2129 device id
rtc: pcf2127: add support for spi interface
rtc: pcf2127: convert to use regmap
rtc: rv3029: Add thermometer hwmon support
rtc: rv3029: Add update_bits helper for eeprom access
rtc: ds1685: actually spin forever in poweroff error path
rtc: hym8563: fix invalid year calculation
rtc: ds3232: use rtc->ops_lock to protect alarm operations
rtc: ds3232: fix issue when irq is shared several devices
rtc: ds3232: remove unused UIE code
rtc: ds3232: add register access error checks
rtc: ds3232: fix read on /dev/rtc after RTC_AIE_ON
rtc: merge ds3232 and ds3234
rtc: ds3232: convert to use regmap
rtc: pxa: fix Kconfig indentation
rtc: rv3029: Add device tree property for trickle charger
rtc: rv3029: Add functions for EEPROM access
rtc: rv3029: Add i2c register update-bits helper
rtc: rv3029: Add missing register definitions
rtc: rv3029: Add "rv3029" I2C device id
...
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.
Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There is different RTC I2C address for RTC block in MAX77686.
Driver is creating dummy i2c client for this address to access
the register of this IP block.
As there is no call to i2c_get_clientdata() for rtc_i2c client,
there is no need to store pointer and hence removing the call
to set client data for rtc i2c client.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add PCI IDs for Intel Broxton B-Step platform, which have same
LPSS devices with A-Step.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
cked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These drivers can be built as module, so make them depend on I2C rather
than I2C=y.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We forgot to remove the clock tree if something goes wrong in ->probe(). Add a
call to intel_lpss_unregister_clock() on error path in ->probe() to fix the
potential issue.
Fixes: 4b45efe852 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
tps65010 driver's initcall cannot succeed when the driver is built-in,
because it expects that the I2C probe is completed at initcall time;
this cannot happen as MFD is initialized before I2C. Also on systems
where the chip is not present there is unnecessary 30 ms delay during
the boot.
Instead of waiting for probe to finish, just register the I2C device.
If some boards need retry mechanism for startup glitches, that should be
done in the actual probe function. Also delete the driver banner message.
The patch allows to use tps65010 again with OMAP1 (where it's required
to be built-in) and enables e.g. USB and LED functionality on OMAP5912 OSK.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes some leftover code style issues in the axp20x core.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp20x driver assumes the device is i2c based. This is not the
case with later chips, which use a proprietary 2 wire serial bus
by Allwinner called "Reduced Serial Bus".
This patch follows the example of mfd/wm831x and splits it into
an interface independent core, and an i2c specific glue layer.
MFD_AXP20X and the new MFD_AXP20X_I2C are changed to tristate
symbols, allowing the driver to be built as modules.
Whitespace and other style errors in the moved i2c specific code
have been fixed. Included but unused header files are removed as
well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Supply a backdated copyright notice.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In axp20x_match_device(), match the of_device_id table bound to the
device driver instead of pointing to axp20x_of_match directly. This
will allow us to keep axp20x_match_device() unmodified when we expand
the axp20x driver into multiple ones covering different interface
types.
of_device_get_match_data() cannot be used here as we need to know if
it failed to get a match, or if the match data value just happened to
be 0, as it is for the AXP152.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The first argument passed to axp20x_match_device(), struct axp20x_dev *,
already contains a pointer to the device. By rearranging some code,
moving the assignment of the pointer before axp20x_match_device() is
called, we can eliminate the second parameter.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for TPS65912 PMIC MFD core. It provides
communication through the I2C and SPI interfaces. It contains
the following components:
- Regulators
- GPIO controller
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the core driver for imx25 touchscreen/adc driver. The module
has one shared ADC and two different conversion queues which use the
ADC. The two queues are identical. Both can be used for general purpose
ADC but one is meant to be used for touchscreens.
This driver is the core which manages the central components and
registers of the TSC/ADC unit. It manages the IRQs and forwards them to
the correct components.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
[ensure correct ADC clock depending on the IPG clock]
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert this driver to use clkdev_create() instead of
clk_register_clkdevs(). The latter API is only used by this driver,
although this driver only allocates one clk to add anyway.
Furthermore, this driver allocates the clk_lookup structure with
devm, but clkdev_drop() will free that structure when passed,
leading to a double free when this driver is removed. Clean it
all up and pave the way for the removal of clk_register_clkdevs().
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the thermal subsystem is a loadable module, the u8500 driver
fails to build:
drivers/thermal/built-in.o: In function `db8500_thermal_probe':
db8500_thermal.c:(.text+0x96c): undefined reference to `thermal_zone_device_register'
drivers/thermal/built-in.o: In function `db8500_thermal_work':
db8500_thermal.c:(.text+0xab4): undefined reference to `thermal_zone_device_update'
This changes the symbol to a tristate, so Kconfig can track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
WARNING: Possible unnecessary 'out of memory' message
+ if (!davinci_vc) {
+ dev_dbg(&pdev->dev,
total: 0 errors, 1 warnings, 154 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ERROR: space prohibited before that ',' (ctx:WxW)
+ da9052_free_irq(da9052, DA9052_IRQ_ADC_EOM , da9052);
total: 1 errors, 0 warnings, 290 lines checked
Cc: Support Opensource <support.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
While we're at it, let's also match the MODULE_LICENSE with the header.
WARNING: please, no space before tabs
+ * ^IMike Rapoport <mike@compulab.co.il>$
WARNING: please, no space before tabs
+ * ^IEric Miao <eric.miao@marvell.com>$
WARNING: quoted string split across lines
+MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>"
+ "Mike Rapoport <mike@compulab.co.il>");
total: 0 errors, 3 warnings, 574 lines checked
Cc: Support Opensource <support.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
WARNING: Comparisons should place the constant on the right side of the test
+ BUG_ON(EC_MSG_PREAMBLE_COUNT > ec_dev->din_size);
WARNING: Comparisons should place the constant on the right side of the test
+ BUG_ON(EC_MSG_PREAMBLE_COUNT > ec_dev->din_size);
total: 0 errors, 2 warnings, 731 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ERROR: code indent should use tabs where possible
+ ^Iec_dev = devm_kzalloc(dev, sizeof(*ec_dev), GFP_KERNEL);$
WARNING: please, no space before tabs
+ ^Iec_dev = devm_kzalloc(dev, sizeof(*ec_dev), GFP_KERNEL);$
WARNING: please, no spaces at the start of a line
+ ^Iec_dev = devm_kzalloc(dev, sizeof(*ec_dev), GFP_KERNEL);$
total: 1 errors, 2 warnings, 366 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ERROR: Macros with complex values should be enclosed in parentheses
+#define INIT_CDEX(_name, _rate) \
+ [ASIC3_CLOCK_##_name] = { \
+ .cdex = CLOCK_CDEX_##_name, \
+ .rate = _rate, \
+ }
WARNING: line over 80 characters
+ ASIC3_GPIO_INT_STATUS);
WARNING: void function return statements are not generally useful
+ return;
+}
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: line over 80 characters
+ asic->tmio_cnf = ioremap((ASIC3_SD_CONFIG_BASE >> asic->bus_shift) +
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ... then dev_err(dev, ... then p
r_err(... to printk(KERN_ERR ...
+ printk(KERN_ERR "kzalloc failed\n");
WARNING: Possible unnecessary 'out of memory' message
+ if (asic == NULL) {
+ printk(KERN_ERR "kzalloc failed\n");
WARNING: Missing a blank line after declarations
+ int retval = 0;
+ retval = platform_driver_probe(&asic3_device_driver, asic3_probe);
total: 1 errors, 13 warnings, 1081 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
WARNING: Possible unnecessary 'out of memory' message
+ if (!pdata) {
+ dev_err(&client->dev, "Failed to allocate pdata\n");
WARNING: Possible unnecessary 'out of memory' message
+ if (!as3711) {
+ dev_err(&client->dev, "Memory allocation failed\n");
WARNING: line over 80 characters
+ dev_err(&client->dev, "regmap initialization failed: %d\n", ret);
WARNING: line over 80 characters
+ /* We can reuse as3711_subdevs[], it will be copied in mfd_add_devices() */
WARNING: line over 80 characters
+ as3711_subdevs[AS3711_REGULATOR].platform_data = &pdata->regulator;
WARNING: line over 80 characters
+ as3711_subdevs[AS3711_REGULATOR].pdata_size = sizeof(pdata->regulator);
WARNING: line over 80 characters
+ as3711_subdevs[AS3711_BACKLIGHT].platform_data = &pdata->backlight;
WARNING: line over 80 characters
+ as3711_subdevs[AS3711_BACKLIGHT].pdata_size = sizeof(pdata->backlight);
total: 0 errors, 8 warnings, 236 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Milo Kim