Commit Graph

4023 Commits

Author SHA1 Message Date
Logan Shaw 2ecff39791 hwmon: (adt7475) Add attenuator bypass support
Added support for reading DTS properties to set attenuators on
device probe for the ADT7473, ADT7475, ADT7476, and ADT7490.

Signed-off-by: Logan Shaw <logan.shaw@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Continuation line formatting; dev_err -> dev_warn]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Henry Shen 0454e799c5 hwmon: (lm73) Add support for of_match_table
Add the of_match_table.

Signed-off-by: Henry Shen <henry.shen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200212030615.28537-3-henry.shen@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Guenter Roeck 6f944004f8 hwmon: (pmbus/tps53679) Add support for TPS53647 and TPS53667
TPS53647 and TPS53667 are single channel, Step-Down Buck Controllers.
TPS53647 supports 4 phases, TPS53667 supports 6 phases.
The chips do not support per-phase output telemetry.

Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Guenter Roeck 53030bcc87 hwmon: (pmbus/tps53679) Add support for TPS53681
TPS53681 is a dual-channel multiphase step-down controller
supporting per-phase and per-channel output telemetry.

Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Guenter Roeck 39c749aca8 hwmon: (pmbus/tps53679) Add support for IIN and PIN to TPS53679 and TPS53688
All chips of this series with published datasheets support IIN, PIN, and
STATUS_INPUT PMBus commands. Per TI Power Management Forum, "TPS53679 and
TPS53681 have the same PMBus command set". There is no reason to believe
that this does not apply to TPS53688. Let's assume that this is correct
and add support for IIN, PIN, and STATUS_INPUT to TPS53679 and TPS53688
to simplify adding support for more chips of the same series.

At the same time, drop reporting VIN on channel 2. On chips with published
datasheets this voltage is identical to the voltage reported on channel 1,
and there is no reason to believe that this is different for TPS53679 and
TPS53888.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Guenter Roeck 63eb4587f6 hwmon: (pmbus/tps53679) Add support for multiple chips IDs
Chip specific support will be needed in the driver to be able to
support additional chips of the same series. Add support for it
to the driver.

To simplify adding support for more chips, call identification code
from the probe function. This lets us use a single structure for common
elements of struct pmbus_driver_info, thus reducing code size as support
for more chips is added.

Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Guenter Roeck 16358542f3 hwmon: (pmbus) Implement multi-phase support
Some PMBus chips support multiple phases, and report telemetry such
as input current, output current, or temperature for each phase.
Add support for such chips to the PMBus core.

Start with a maximum of 8 phases per page, and assume that supported
sensors per phase are similar for all pages. Only support per-phase
telemetry attributes, no limits or alarms.

As part of this patch, set the initial page variable to 0xff to ensure
that the page is updated when the first page command is issued. Also
only issue page commands if the chip supports more than one page.

Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Guenter Roeck 43f33b6e59 hwmon: (pmbus) Add 'phase' parameter where needed for multi-phase support
In preparation for multi-phase support, add 'phase' parameter to read_word
and set_page functions. Actual multi-phase support will be added in
a subsequent patch.

Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Guenter Roeck a1dd176c42 hwmon: (pmbus) Add IC_DEVICE_ID and IC_DEVICE_REV command definitions
Recent PMBus versions added IC_DEVICE_ID and IC_DEVICE_REV commands as
additional means to identify the chip. Add command definitions to
pmbus.h include file.

Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:47 -07:00
Gustavo A. R. Silva afde6416e1 hwmon: (ibmaem) Replace zero-length array with flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211234237.GA26971@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:46 -07:00
Guenter Roeck 60465245e6 hwmon: (k10temp) Reorganize and simplify temperature support detection
Use a bit map to describe if temperature channels are supported,
and use it for all temperature channels. Use a separate flag,
independent of Tdie support, to indicate if the system is running
on a Ryzen CPU.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:46 -07:00
Guenter Roeck b02c685738 hwmon: (k10temp) Swap Tdie and Tctl on Family 17h CPUs
Traditionally, the temperature displayed by k10temp was Tctl.
On Family 17h CPUs, Tdie was displayed instead. To reduce confusion,
Tctl was added later as second temperature. This resulted in Tdie
being reported as temp1_input, and Tctl as temp2_input. This is
different to non-Ryzen CPUs, where Tctl is displayed as temp1_input.
Swap temp1_input and temp2_input on Family 17h CPUs, such that Tctl
is now reported as temp1_input and Tdie is reported as temp2_input,
to align with other CPUs, streamline the code, and make it less
confusing. Coincidentally, this also aligns the code with its
documentation, which states that Tdie is reported as temp2_input.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:46 -07:00
Mike Jones ee44fafb38 hwmon: (pmbus/ltc2978) add support for more parts.
LTC2972, LTC2979, LTC3884, LTC3889, LTC7880, LTM4664, LTM4677,
LTM4678, LTM4680, LTM4700.

Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1581032654-4330-1-git-send-email-michael-a1.jones@analog.com
[groeck: Fixed checkpatch issues (long lines, whitespace)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:46 -07:00
Nuno Sá 8412b410fa hwmon: Support ADI Fan Control IP
The purpose of this IP Core is to control the fan used for the cooling of a
Xilinx Zynq Ultrascale+ MPSoC without the need of any external temperature
sensors. To achieve this, the IP core uses the PL SYSMONE4 primitive to
obtain the PL temperature and, based on those readings, it then outputs
a PWM signal to control the fan rotation accordingly.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191009102806.262241-1-nuno.sa@analog.com
[groeck: adi,pulses-per-revolution -> pulses-per-revolution;
 dropped unused 'res' from probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:46 -07:00
Dan Carpenter 44f2f88290 hwmon: (adt7462) Fix an error return in ADT7462_REG_VOLT()
This is only called from adt7462_update_device().  The caller expects it
to return zero on error.  I fixed a similar issue earlier in commit
a4bf06d58f ("hwmon: (adt7462) ADT7462_REG_VOLT_MAX() should return 0")
but I missed this one.

Fixes: c0b4e3ab0c ("adt7462: new hwmon driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Link: https://lore.kernel.org/r/20200303101608.kqjwfcazu2ylhi2a@kili.mountain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-03 12:42:55 -08:00
Vadim Pasternak deddc9e8c0 hwmon: (pmbus/xdpe12284) Add callback for vout limits conversion
Provide read_word_data() callback for overvoltage and undervoltage
output readouts conversion. These registers are presented in
'slinear11' format, while default conversion for 'vout' class for the
devices is 'vid'. It is resulted in wrong conversion in pmbus_reg2data()
for in{3-4}_lcrit and in{3-4}_crit attributes.
)
Fixes: aaafb7c8eb ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200224225202.19576-1-vadimp@mellanox.com
[gropeck: Adjusted to mainline PMBus API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-02-25 13:23:26 -08:00
Guenter Roeck e61d239225 hwmon: (w83627ehf) Fix crash seen with W83627DHG-P
Loading the driver on a system with W83627DHG-P crashes as follows.

w83627ehf: Found W83627DHG-P chip at 0x290
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 0 PID: 604 Comm: sensors Not tainted 5.6.0-rc2-00055-gca7e1fd1026c #29
Hardware name:  /D425KT, BIOS MWPNT10N.86A.0132.2013.0726.1534 07/26/2013
RIP: 0010:w83627ehf_read_string+0x27/0x70 [w83627ehf]
Code: [... ]
RSP: 0018:ffffb95980657df8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff96caaa7f5218 RCX: 0000000000000000
RDX: 0000000000000015 RSI: 0000000000000001 RDI: ffff96caa736ec08
RBP: 0000000000000000 R08: ffffb95980657e20 R09: 0000000000000001
R10: ffff96caaa635cc0 R11: 0000000000000000 R12: ffff96caa9f7cf00
R13: ffff96caa9ec3d00 R14: ffff96caa9ec3d28 R15: ffff96caa9ec3d40
FS:  00007fbc7c4e2740(0000) GS:ffff96caabc00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000129d58000 CR4: 00000000000006f0
Call Trace:
 ? cp_new_stat+0x12d/0x160
 hwmon_attr_show_string+0x37/0x70 [hwmon]
 dev_attr_show+0x14/0x50
 sysfs_kf_seq_show+0xb5/0x1b0
 seq_read+0xcf/0x460
 vfs_read+0x9b/0x150
 ksys_read+0x5f/0xe0
 do_syscall_64+0x48/0x190
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
...

Temperature labels are not always present. Adjust sysfs attribute
visibility accordingly.

Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Dr. David Alan Gilbert <linux@treblig.org>
Fixes: 266cd58359 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-02-21 09:16:24 -08:00
Guenter Roeck badcd4546d hwmon: (acpi_power_meter) Fix lockdep splat
Damien Le Moal reports a lockdep splat with the acpi_power_meter,
observed with Linux v5.5 and later.

======================================================
WARNING: possible circular locking dependency detected
5.6.0-rc2+ #629 Not tainted
------------------------------------------------------
python/1397 is trying to acquire lock:
ffff888619080070 (&resource->lock){+.+.}, at: show_power+0x3c/0xa0 [acpi_power_meter]

               but task is already holding lock:
ffff88881643f188 (kn->count#119){++++}, at: kernfs_seq_start+0x6a/0x160

               which lock already depends on the new lock.

               the existing dependency chain (in reverse order) is:

               -> #1 (kn->count#119){++++}:
       __kernfs_remove+0x626/0x7e0
       kernfs_remove_by_name_ns+0x41/0x80
       remove_attrs+0xcb/0x3c0 [acpi_power_meter]
       acpi_power_meter_notify+0x1f7/0x310 [acpi_power_meter]
       acpi_ev_notify_dispatch+0x198/0x1f3
       acpi_os_execute_deferred+0x4d/0x70
       process_one_work+0x7c8/0x1340
       worker_thread+0x94/0xc70
       kthread+0x2ed/0x3f0
       ret_from_fork+0x24/0x30

               -> #0 (&resource->lock){+.+.}:
       __lock_acquire+0x20be/0x49b0
       lock_acquire+0x127/0x340
       __mutex_lock+0x15b/0x1350
       show_power+0x3c/0xa0 [acpi_power_meter]
       dev_attr_show+0x3f/0x80
       sysfs_kf_seq_show+0x216/0x410
       seq_read+0x407/0xf90
       vfs_read+0x152/0x2c0
       ksys_read+0xf3/0x1d0
       do_syscall_64+0x95/0x1010
       entry_SYSCALL_64_after_hwframe+0x49/0xbe

               other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(kn->count#119);
                               lock(&resource->lock);
                               lock(kn->count#119);
  lock(&resource->lock);

                *** DEADLOCK ***
4 locks held by python/1397:
 #0: ffff8890242d64e0 (&f->f_pos_lock){+.+.}, at: __fdget_pos+0x9b/0xb0
 #1: ffff889040be74e0 (&p->lock){+.+.}, at: seq_read+0x6b/0xf90
 #2: ffff8890448eb880 (&of->mutex){+.+.}, at: kernfs_seq_start+0x47/0x160
 #3: ffff88881643f188 (kn->count#119){++++}, at: kernfs_seq_start+0x6a/0x160

               stack backtrace:
CPU: 10 PID: 1397 Comm: python Not tainted 5.6.0-rc2+ #629
Hardware name: Supermicro Super Server/X11DPL-i, BIOS 3.1 05/21/2019
Call Trace:
 dump_stack+0x97/0xe0
 check_noncircular+0x32e/0x3e0
 ? print_circular_bug.isra.0+0x1e0/0x1e0
 ? unwind_next_frame+0xb9a/0x1890
 ? entry_SYSCALL_64_after_hwframe+0x49/0xbe
 ? graph_lock+0x79/0x170
 ? __lockdep_reset_lock+0x3c0/0x3c0
 ? mark_lock+0xbc/0x1150
 __lock_acquire+0x20be/0x49b0
 ? mark_held_locks+0xe0/0xe0
 ? stack_trace_save+0x91/0xc0
 lock_acquire+0x127/0x340
 ? show_power+0x3c/0xa0 [acpi_power_meter]
 ? device_remove_bin_file+0x10/0x10
 ? device_remove_bin_file+0x10/0x10
 __mutex_lock+0x15b/0x1350
 ? show_power+0x3c/0xa0 [acpi_power_meter]
 ? show_power+0x3c/0xa0 [acpi_power_meter]
 ? mutex_lock_io_nested+0x11f0/0x11f0
 ? lock_downgrade+0x6a0/0x6a0
 ? kernfs_seq_start+0x47/0x160
 ? lock_acquire+0x127/0x340
 ? kernfs_seq_start+0x6a/0x160
 ? device_remove_bin_file+0x10/0x10
 ? show_power+0x3c/0xa0 [acpi_power_meter]
 show_power+0x3c/0xa0 [acpi_power_meter]
 dev_attr_show+0x3f/0x80
 ? memset+0x20/0x40
 sysfs_kf_seq_show+0x216/0x410
 seq_read+0x407/0xf90
 ? security_file_permission+0x16f/0x2c0
 vfs_read+0x152/0x2c0

Problem is that reading an attribute takes the kernfs lock in the kernfs
code, then resource->lock in the driver. During an ACPI notification, the
opposite happens: The resource lock is taken first, followed by the kernfs
lock when sysfs attributes are removed and re-created. Presumably this is
now seen due to some locking related changes in kernfs after v5.4, but it
was likely always a problem.

Fix the problem by not blindly acquiring the lock in the notification
function. It is only needed to protect the various update functions.
However, those update functions are called anyway when sysfs attributes
are read. This means that we can just stop calling those functions from
the notifier, and the resource lock in the notifier function is no longer
needed.

That leaves two situations:

First, METER_NOTIFY_CONFIG removes and re-allocates capability strings.
While it did so under the resource lock, _displaying_ those strings was not
protected, creating a race condition. To solve this problem, selectively
protect both removal/creation and reporting of capability attributes with
the resource lock.

Second, removing and re-creating the attribute files is no longer protected
by the resource lock. That doesn't matter since access to each individual
attribute is protected by the kernfs lock. Userspace may get messed up if
attributes disappear and reappear under its nose, but that is not different
than today, and there is nothing we can do about it without major driver
restructuring.

Last but not least, when removing the driver, remove attribute functions
first, then release capability strings. This avoids yet another race
condition.

Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: stable@vger.kernel.org # v5.5+
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-02-19 17:25:15 -08:00
Johan Hovold 205447fa9e hwmon: (pmbus/xdpe12284) fix typo in compatible strings
Make sure that the driver compatible strings matches the binding by
removing the space between the manufacturer and model.

Fixes: aaafb7c8eb ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200212092426.24012-1-johan@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-02-12 12:43:01 -08:00
Mike Jones cf2b012c90 hwmon: (pmbus/ltc2978) Fix PMBus polling of MFR_COMMON definitions.
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.

Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bb ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-02-09 18:41:08 -08:00
Linus Torvalds eab3540562 ARM: SoC-related driver updates
Various driver updates for platforms:
 
  - Nvidia: Fuse support for Tegra194, continued memory controller pieces
    for Tegra30
 
  - NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
 
  - NXP/FSL: i.MX8MP SoC driver pieces
 
  - TI Keystone: ring accelerator driver
 
  - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
 
  - Xilinx ZynqMP: feature checking interface for firmware. Mailbox
    communication for power management
 
  - Overall support patch set for cpuidle on more complex hierarchies
    (PSCI-based)
 
 + Misc cleanups, refactorings of Marvell, TI, other platforms.
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl4+lTYPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3nQcQAJm91+6hZbmMjlBySGS7ISjYvOcrI/hMgiOl
 uhhEP0Dcylvf9A9x3wcIbLwixe+2pvie9DQh2u5F80ShYimidtFi/2xCfuTb9fKu
 sxxKjrXWyVKhkpW0z+tedY08ftVhkwwcyD4m2C7uVl6AwTP7c367vFeU7XjF2APn
 drfgmgbjm8U3XbSyAqv+k6z6tyqaCnFM7vbPupSKHgHJ3mfByxOa+XyBN2RdgBbs
 0KrVfbXGv80zFIFrMPwaWG7G52bu7K68nVdgy44MpKdRZ6QTjhnR+kerFxHsYgV4
 bM55Fya52nTCSTGdKaQakDtKwbAUdCDTSkxgOHGcQoyFi0R/VaEUJtcysnvLbI6c
 +n/yFIzGyEdXcvIzfv2SoDYhogw19I6RR/M9K5Ni29eazkDVYx2z3rI+2QYeqCiF
 u7cq52gW6JLP0SI/9kuUrRFiR8v19Ixap7qokAxgqQwYB3NzT8a7WsYPkzdpDZGQ
 ETSDFMyBWT6UvBe/HWkQluBabbet53rG8BF0OHFrQuMK0u/ieKgSGuTB9XN2djEW
 PHMOMz2vhi+8XTfpkskhF2tTxlA/k4R6QwCdIMpIkMRVnVQCh1XdPr3Fi2NrgB+S
 kIXHD4vV6zLYh04zHyKewSPHAXWgraFpg2qKnvL5+KWMTnW6QH+RNjOt9xKDNXOd
 +iDXpOad
 =ONtb
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - Nvidia: Fuse support for Tegra194, continued memory controller
     pieces for Tegra30

   - NXP/FSL: Refactorings of QuickEngine drivers to support
     ARM/ARM64/PPC

   - NXP/FSL: i.MX8MP SoC driver pieces

   - TI Keystone: ring accelerator driver

   - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.

   - Xilinx ZynqMP: feature checking interface for firmware. Mailbox
     communication for power management

   - Overall support patch set for cpuidle on more complex hierarchies
     (PSCI-based)

  and misc cleanups, refactorings of Marvell, TI, other platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
  drivers: soc: xilinx: Use mailbox IPI callback
  dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
  drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
  MAINTAINERS: Add brcmstb PCIe controller entry
  soc/tegra: fuse: Unmap registers once they are not needed anymore
  soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
  soc/tegra: fuse: Warn if straps are not ready
  soc/tegra: fuse: Cache values of straps and Chip ID registers
  memory: tegra30-emc: Correct error message for timed out auto calibration
  memory: tegra30-emc: Firm up hardware programming sequence
  memory: tegra30-emc: Firm up suspend/resume sequence
  soc/tegra: regulators: Do nothing if voltage is unchanged
  memory: tegra: Correct reset value of xusb_hostr
  soc/tegra: fuse: Add APB DMA dependency for Tegra20
  bus: tegra-aconnect: Remove PM_CLK dependency
  dt-bindings: mediatek: add MT6765 power dt-bindings
  soc: mediatek: cmdq: delete not used define
  memory: tegra: Add support for the Tegra194 memory controller
  memory: tegra: Only include support for enabled SoCs
  memory: tegra: Support DVFS on Tegra186 and later
  ...
2020-02-08 14:04:19 -08:00
Alexey Dobriyan 97a32539b9 proc: convert everything to "struct proc_ops"
The most notable change is DEFINE_SHOW_ATTRIBUTE macro split in
seq_file.h.

Conversion rule is:

	llseek		=> proc_lseek
	unlocked_ioctl	=> proc_ioctl

	xxx		=> proc_xxx

	delete ".owner = THIS_MODULE" line

[akpm@linux-foundation.org: fix drivers/isdn/capi/kcapi_proc.c]
[sfr@canb.auug.org.au: fix kernel/sched/psi.c]
  Link: http://lkml.kernel.org/r/20200122180545.36222f50@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191225172546.GB13378@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-02-04 03:05:26 +00:00
Linus Torvalds 6a1000bd27 ioremap changes for 5.6
- remove ioremap_nocache given that is is equivalent to
    ioremap everywhere
 -----BEGIN PGP SIGNATURE-----
 
 iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAl4vKHwLHGhjaEBsc3Qu
 ZGUACgkQD55TZVIEUYMPGBAAuVNUZaZfWYHpiVP2oRcUQUguFiD3NTbknsyzV2oH
 J9P0GfeENSKwE9OOhZ7XIjnCZAJwQgTK/ppQY5yiQ/KAtYyyXjXEJ6jqqjiTDInr
 +3+I3t/LhkgrK7tMrb7ylTGa/d7KhaciljnOXC8+b75iddvM9I1z2pbHDbppZMS9
 wT4RXL/cFtRb85AfOyPLybcka3f5P2gGvQz38qyimhJYEzHDXZu9VO1Bd20f8+Xf
 eLBKX0o6yWMhcaPLma8tm0M0zaXHEfLHUKLSOkiOk+eHTWBZ3b/w5nsOQZYZ7uQp
 25yaClbameAn7k5dHajduLGEJv//ZjLRWcN3HJWJ5vzO111aHhswpE7JgTZJSVWI
 ggCVkytD3ESXapvswmACSeCIDMmiJMzvn6JvwuSMVB7a6e5mcqTuGo/FN+DrBF/R
 IP+/gY/T7zIIOaljhQVkiEIIwiD/akYo0V9fheHTBnqcKEDTHV4WjKbeF6aCwcO+
 b8inHyXZSKSMG//UlDuN84/KH/o1l62oKaB1uDIYrrL8JVyjAxctWt3GOt5KgSFq
 wVz1lMw4kIvWtC/Sy2H4oB+RtODLp6yJDqmvmPkeJwKDUcd/1JKf0KsZ8j3FpGei
 /rEkBEss0KBKyFAgBSRO2jIpdj2epgcBcsdB/r5mlhcn8L77AS6mHbA173kY4pQ/
 Kdg=
 =TUCJ
 -----END PGP SIGNATURE-----

Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap

Pull ioremap updates from Christoph Hellwig:
 "Remove the ioremap_nocache API (plus wrappers) that are always
  identical to ioremap"

* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
  remove ioremap_nocache and devm_ioremap_nocache
  MIPS: define ioremap_nocache to ioremap
2020-01-27 13:03:00 -08:00
Guenter Roeck fd8bdb23b9 hwmon: (k10temp) Display up to eight sets of CCD temperatures
In HWiNFO, we see support for Tccd1, Tccd3, Tccd5, and Tccd7 temperature
sensors on Zen2 based Threadripper CPUs. Checking register maps on
Threadripper 3970X confirms SMN register addresses and values for those
sensors.

Register values observed in an idle system:

0x059950: 00000000 00000abc 00000000 00000ad8
0x059960: 00000000 00000ade 00000000 00000ae4

Under load:

0x059950: 00000000 00000c02 00000000 00000c14
0x059960: 00000000 00000c30 00000000 00000c22

More analysis shows that EPYC CPUs support up to 8 CCD temperature
sensors. EPYC 7601 supports three CCD temperature sensors. Unlike
Zen2 CPUs, the register space in Zen1 CPUs supports a maximum of four
sensors, so only search for a maximum of four sensors on Zen1 CPUs.

On top of that, in thm_10_0_sh_mask.h in the Linux kernel, we find
definitions for THM_DIE{1-3}_TEMP__VALID_MASK, set to 0x00000800, as well
as matching SMN addresses. This lets us conclude that bit 11 of the
respective registers is a valid bit. With this assumption, the temperature
offset is now 49 degrees C. This conveniently matches the documented
temperature offset for Tdie, again suggesting that above registers indeed
report temperatures sensor values. Assume that bit 11 is indeed a valid
bit, and add support for the additional sensors.

With this patch applied, output from 3970X (idle) looks as follows:

k10temp-pci-00c3
Adapter: PCI adapter
Tdie:         +55.9°C
Tctl:         +55.9°C
Tccd1:        +39.8°C
Tccd3:        +43.8°C
Tccd5:        +43.8°C
Tccd7:        +44.8°C

Tested-by: Michael Larabel <michael@phoronix.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 15:17:59 -08:00
Guenter Roeck 9c4a38f19e hwmon: (k10temp) Add debugfs support
Show thermal and SVI registers for Family 17h CPUs.

Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Guenter Roeck 70831c8a91 hwmon: (k10temp) Don't show temperature limits on Ryzen (Zen) CPUs
The maximum Tdie or Tctl is not published for Ryzen CPUs. What is
known, however, is that the traditional value of 70 degrees C is no
longer correct. On top of that, the limit applies to Tctl, not to Tdie.
Displaying it in either context is meaningless, confusing, and wrong.
Stop doing it.

Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Guenter Roeck b00647c46c hwmon: (k10temp) Show core and SoC current and voltages on Ryzen CPUs
Ryzen CPUs report core and SoC voltages and currents. Add support
for it to the k10temp driver.

For the time being, only report voltages and currents for Ryzen
CPUs. Threadripper and EPYC appear to use a different mechanism.

Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Guenter Roeck c757938929 hwmon: (k10temp) Report temperatures per CPU die
Zen2 reports reporting temperatures per CPU die (called Core Complex Dies,
or CCD, by AMD). Add support for it to the k10temp driver.

Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Guenter Roeck d547552a1b hmon: (k10temp) Convert to use devm_hwmon_device_register_with_info
Convert driver to use devm_hwmon_device_register_with_info to simplify
the code and to reduce its size.

Old size (x86_64):
   text	   data	    bss	    dec	    hex	filename
   8247	   4488	     64	  12799	   31ff	drivers/hwmon/k10temp.o
New size:
   text	   data	    bss	    dec	    hex	filename
   6778	   2792	     64	   9634	   25a2	drivers/hwmon/k10temp.o

Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Guenter Roeck a6d210da1a hwmon: (k10temp) Use bitops
Using bitops makes bit masks and shifts easier to read.

Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Akinobu Mita 7992db7cb9 hwmon: (pwm-fan) stop fan on shutdown
The pwm-fan driver stops the fan in suspend but leaves the fan on in
shutdown.  It seems strange to leave the fan on in shutdown because there
is no use case in my mind and the gpio-fan driver on the other hand stops
in shutdown.

This change turns off the fan in shutdown.  If anyone complains then we'll
add an optional property to switch the behavior.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kamil Debski <kamil@wypas.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/1579534344-11694-1-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Beniamin Bia 09b08ac9e8 hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
ADM1177 is a Hot Swap Controller and Digital Power Monitor with
Soft Start Pin.

Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Link: https://lore.kernel.org/r/20200114112159.25998-1-beniamin.bia@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Vadim Pasternak aaafb7c8eb hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers
Add support for devices XDPE12254, XDPE12284.

All these device support two pages.
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps, supported by these
devices:
VR12.0 mode, 5-mV DAC - 0x01;
VR12.5 mode, 10-mV DAC - 0x02;
IMVP9 mode, 5-mV DAC - 0x03;
AMD mode 6.25mV - 0x10.

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-5-vadimp@mellanox.com
[groeck: Added missing break statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Vadim Pasternak 583dc92127 hwmon: (pmbus/tps53679) Extend device list supported by driver
Extends driver with support of the additional devices:
Texas Instruments Dual channel DCAP+ multiphase controllers: TPS53688.

Extend Kconfig with added device.

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-4-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Vadim Pasternak 9d72340b6a hwmon: (pmbus/core) Add support for Intel IMVP9 and AMD 6.25mV modes
Extend "vrm_version" with the type for Intel IMVP9 and AMD 6.25mV VID
modes.
Add calculation for those types.

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-3-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Vadim Pasternak b9fa0a3acf hwmon: (pmbus/core) Add support for vid mode detection per page bases
Add support for VID protocol detection per page bases, instead of
detecting it based on "PMBU_VOUT" readout from page 0 for all the pages
supported by particular device.
The reason that some devices allows to configure different VID modes
per page within the same device.
Patch modifies the field "vrm_version" within the structure
"pmbus_driver_info" to be per page array.

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-2-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Eddie James d9c8ae69b9 hwmon: (pmbus/ibm-cffps) Prevent writing on_off_config with bad data
If the user write parameters resulted in no bytes being written to the
temporary buffer, then ON_OFF_CONFIG will be written with uninitialized
data. Prevent this by bailing out in this case.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1578411640-16929-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
YueHaibing 392923715d hwmon: (w83627ehf) Remove set but not used variable 'fan4min'
Fixes gcc '-Wunused-but-set-variable' warning:

drivers/hwmon/w83627ehf.c: In function 'w83627ehf_check_fan_inputs':
drivers/hwmon/w83627ehf.c:1296:24: warning:
 variable 'fan4min' set but not used [-Wunused-but-set-variable]

commit 62000264cfa8 ("hwmon: (w83627ehf) remove nct6775 and nct6776 support")
left behind this unused variable.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200108034514.50130-1-yuehaibing@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Guenter Roeck 5b46903d8b hwmon: Driver for disk and solid state drives with temperature sensors
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.

This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.

With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:

$ sensors drivetemp-scsi-1-0
drivetemp-scsi-1-0
Adapter: SCSI adapter
temp1:        +23.0°C

or directly from sysfs:

$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000

If the drive supports SCT transport and reports temperature limits,
those are reported as well.

drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1:        +27.0°C  (low  =  +0.0°C, high = +60.0°C)
                       (crit low = -41.0°C, crit = +85.0°C)
                       (lowest = +23.0°C, highest = +34.0°C)

The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.

Cc: Chris Healy <cphealy@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Eddie James 74a71a831b hwmon: (pmbus/ibm-cffps) Fix the LED behavior when turned off
The driver should remain in control of the LED on the PSU, even while
off, not the PSU firmware as previously indicated.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1576788607-13567-4-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Eddie James 1952d79a0d hwmon: (pmbus/ibm-cffps) Add the VMON property for version 2
Version 2 of the PSU supports reading an auxiliary voltage. Use the
pmbus VMON property and associated virtual register to read it.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1576788607-13567-3-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Eddie James abe508b66d hwmon: (pmbus/ibm-cffps) Add new manufacturer debugfs entries
Add support for a number of manufacturer-specific registers in the
debugfs entries, as well as support to read and write the
PMBUS_ON_OFF_CONFIG register through debugfs.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1576788607-13567-2-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Guenter Roeck cce209581a hwmon: (pmbus) Driver for MAX20730, MAX20734, and MAX20743
Add support for Maxim MAX20730, MAX20734, MAX20743 Integrated,
Step-Down Switching Regulators with PMBus support.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Dr. David Alan Gilbert 931f397bc6 hwmon: (w83627ehf) Now only one intrusion channel
The 2nd intrusion channel was only used on the nct6776

Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191225023225.2785-4-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Dr. David Alan Gilbert 695955028a hwmon: (w83627ehf) Remove code not needed after nct677* removal
Now the nct677* are gone, we can clean up some flags that are
always the same now and simplify some code.

Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191225023225.2785-3-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Dr. David Alan Gilbert 3207408ab4 hwmon: (w83627ehf) remove nct6775 and nct6776 support
The nct6775 and nct6776 are supported by the separate nct6775.c driver,
so remove the code from the w83627ehf driver.

Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191225023225.2785-2-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Guenter Roeck 1a1ea120af hwmon: (pmbus) Add MAX20796 to devices supported by generic pmbus driver
MAX20796 is a dual-phase scalable integrated voltage regulator with
PMBus interface.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Chen Zhou 8f77203587 hwmon: (w83627ehf) make sensor_dev_attr_##_name variables static
Fix sparse warning:

drivers/hwmon/w83627ehf.c:1202:1: warning:
	symbol 'sensor_dev_attr_pwm1_target' was not declared. Should it be static?

and many more similar messages.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Link: https://lore.kernel.org/r/20191213015605.172472-1-chenzhou10@huawei.com
[groeck: Dropped all but one log message from description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Guenter Roeck 9e347728c4 hwmon: (pmbus) Detect if chip is write protected
If a chip is write protected, we can not change any limits, and we can
not clear status flags. This may be the reason why clearing status flags
is reported to not work for some chips. Detect the condition in the pmbus
core. If the chip is write protected, set limit attributes as read-only,
and set the flag indicating that the status flag should be ignored.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Guenter Roeck d21ed22ba7 hwmon: Driver for MAX31730
MAX31730 is a 3-Channel Remote Temperature Sensor.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Guenter Roeck 002c6b545b hwmon: Add support for enable attributes to hwmon core
The hwmon ABI supports enable attributes since commit fb41a710f8
("hwmon: Document the sensor enable attribute"), but did not
add support for those attributes to the hwmon core. Do that now.

Since the enable attributes are logically the most important attributes,
they are added as first attribute to the attribute list. Move
hwmon_in_enable from last to first place for consistency.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Dr. David Alan Gilbert 266cd58359 hwmon: (w83627ehf) convert to with_info interface
Convert the old hwmon_device_register code to
devm_hwmon_device_register_with_info.

Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191124202030.45360-3-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Jim Wright a470f11c5b hwmon: (pmbus/ucd9000) Add support for UCD90320 Power Sequencer
Add support for the UCD90320 chip and its expanded set of GPIO pins.

Signed-off-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20191205232411.21492-3-wrightj@linux.vnet.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Dr. David Alan Gilbert 4413405f93 hwmon: Add intrusion templates
Add templates for intrusion%d_alarm and intrusion%d_beep.
Note, these start at 0.

Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191124202030.45360-2-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Guenter Roeck 3bf8bdcf3b hwmon: (core) Do not use device managed functions for memory allocations
The hwmon core uses device managed functions, tied to the hwmon parent
device, for various internal memory allocations. This is problematic
since hwmon device lifetime does not necessarily match its parent's
device lifetime. If there is a mismatch, memory leaks will accumulate
until the parent device is released.

Fix the problem by managing all memory allocations internally. The only
exception is memory allocation for thermal device registration, which
can be tied to the hwmon device, along with thermal device registration
itself.

Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Cc: stable@vger.kernel.org # v4.14.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.14.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9.x: 3a412d5e4a1c: hwmon: (core) Simplify sysfs attribute name allocation
Cc: stable@vger.kernel.org # v4.9.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.9.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9+
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-17 07:57:16 -08:00
Luuk Paulussen cf3ca18775 hwmon: (adt7475) Make volt2reg return same reg as reg2volt input
reg2volt returns the voltage that matches a given register value.
Converting this back the other way with volt2reg didn't return the same
register value because it used truncation instead of rounding.

This meant that values read from sysfs could not be written back to sysfs
to set back the same register value.

With this change, volt2reg will return the same value for every voltage
previously returned by reg2volt (for the set of possible input values)

Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191205231659.1301-1-luuk.paulussen@alliedtelesis.co.nz
cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-17 07:56:48 -08:00
Gilles Buloz e51a7dda29 hwmon: (nct7802) Fix non-working alarm on voltages
No alarm is reported by /sys/.../inX_alarm

In detail:

The SMI Voltage status register is the only register giving a status
for voltages, but it does not work like the non-SMI status registers
used for temperatures and fans.
A bit is set for each input crossing a threshold, in both direction,
but the "inside" or "outside" limits info is not available.
Also this register is cleared on read.
Note : this is not explicitly spelled out in the datasheet, but from
experiment.
As a result if an input is crossing a threshold (min or max in any
direction), the alarm is reported only once even if the input is
still outside limits. Also if the alarm for another input is read
before the one of this input, no alarm is reported at all.

Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f566.tBga5POKAgHlmd0p%gilles.buloz@kontron.com
Fixes: 3434f37835 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-17 07:56:48 -08:00
Gilles Buloz 7713e62c86 hwmon: (nct7802) Fix voltage limits to wrong registers
in0 thresholds are written to the in2 thresholds registers
in2 thresholds to in3 thresholds
in3 thresholds to in4 thresholds
in4 thresholds to in0 thresholds

Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f509.rc0oEvPOMjbfPW1w%gilles.buloz@kontron.com
Fixes: 3434f37835 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-17 07:56:48 -08:00
Christoph Hellwig 4bdc0d676a remove ioremap_nocache and devm_ioremap_nocache
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2020-01-06 09:45:59 +01:00
Sudeep Holla b017b2791c hwmon: (scmi-hwmon) Match scmi device by both name and protocol id
The scmi bus now has support to match the driver with devices not only
based on their protocol id but also based on their device name if one is
available. This was added to cater the need to support multiple devices
and drivers for the same protocol.

Let us add the name "hwmon" to scmi_device_id table in the driver so
that in matches only with device with the same name and protocol id
SCMI_PROTOCOL_SENSOR. This is just for sake of completion and must
not be used to add IIO support in parallel. Instead, if IIO support is
added ever in future, we need to drop this hwmon driver entirely and
use the iio->hwmon bridge to access the sensors as hwmon devices if
needed.

Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2019-12-24 11:37:35 +00:00
Linus Torvalds 0da522107e compat_ioctl: remove most of fs/compat_ioctl.c
As part of the cleanup of some remaining y2038 issues, I came to
 fs/compat_ioctl.c, which still has a couple of commands that need support
 for time64_t.
 
 In completely unrelated work, I spent time on cleaning up parts of this
 file in the past, moving things out into drivers instead.
 
 After Al Viro reviewed an earlier version of this series and did a lot
 more of that cleanup, I decided to try to completely eliminate the rest
 of it and move it all into drivers.
 
 This series incorporates some of Al's work and many patches of my own,
 but in the end stops short of actually removing the last part, which is
 the scsi ioctl handlers. I have patches for those as well, but they need
 more testing or possibly a rewrite.
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJdsHCdAAoJEJpsee/mABjZtYkP/1JGl3jFv3Iq/5BCdPkaePP1
 RtMJRNfURgK3GeuHUui330PvVjI/pLWXU/VXMK2MPTASpJLzYz3uCaZrpVWEMpDZ
 +ImzGmgJkITlW1uWU3zOcQhOxTyb1hCZ0Ci+2xn9QAmyOL7prXoXCXDWv3h6iyiF
 lwG+nW+HNtyx41YG+9bRfKNoG0ZJ+nkJ70BV6u0acQHXWn7Xuupa9YUmBL87hxAL
 6dlJfLTJg6q8QSv/Q6LxslfWk2Ti8OOJZOwtFM5R8Bgl0iUcvshiRCKfv/3t9jXD
 dJNvF1uq8z+gracWK49Qsfq5dnZ2ZxHFUo9u0NjbCrxNvWH/sdvhbaUBuJI75seH
 VIznCkdxFhrqitJJ8KmxANxG08u+9zSKjSlxG2SmlA4qFx/AoStoHwQXcogJscNb
 YIXYKmWBvwPzYu09QFAXdHFPmZvp/3HhMWU6o92lvDhsDwzkSGt3XKhCJea4DCaT
 m+oCcoACqSWhMwdbJOEFofSub4bY43s5iaYuKes+c8O261/Dwg6v/pgIVez9mxXm
 TBnvCsotq5m8wbwzv99eFqGeJH8zpDHrXxEtRR5KQqMqjLq/OQVaEzmpHZTEuK7n
 e/V/PAKo2/V63g4k6GApQXDxnjwT+m0aWToWoeEzPYXS6KmtWC91r4bWtslu3rdl
 bN65armTm7bFFR32Avnu
 =lgCl
 -----END PGP SIGNATURE-----

Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground

Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
 "As part of the cleanup of some remaining y2038 issues, I came to
  fs/compat_ioctl.c, which still has a couple of commands that need
  support for time64_t.

  In completely unrelated work, I spent time on cleaning up parts of
  this file in the past, moving things out into drivers instead.

  After Al Viro reviewed an earlier version of this series and did a lot
  more of that cleanup, I decided to try to completely eliminate the
  rest of it and move it all into drivers.

  This series incorporates some of Al's work and many patches of my own,
  but in the end stops short of actually removing the last part, which
  is the scsi ioctl handlers. I have patches for those as well, but they
  need more testing or possibly a rewrite"

* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
  scsi: sd: enable compat ioctls for sed-opal
  pktcdvd: add compat_ioctl handler
  compat_ioctl: move SG_GET_REQUEST_TABLE handling
  compat_ioctl: ppp: move simple commands into ppp_generic.c
  compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
  compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
  compat_ioctl: unify copy-in of ppp filters
  tty: handle compat PPP ioctls
  compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
  compat_ioctl: handle SIOCOUTQNSD
  af_unix: add compat_ioctl support
  compat_ioctl: reimplement SG_IO handling
  compat_ioctl: move WDIOC handling into wdt drivers
  fs: compat_ioctl: move FITRIM emulation into file systems
  gfs2: add compat_ioctl support
  compat_ioctl: remove unused convert_in_user macro
  compat_ioctl: remove last RAID handling code
  compat_ioctl: remove /dev/raw ioctl translation
  compat_ioctl: remove PCI ioctl translation
  compat_ioctl: remove joystick ioctl translation
  ...
2019-12-01 13:46:15 -08:00
Linus Torvalds 3d9e3501a0 hwmon updates for v5.5
- Added support for Texas Instruments TMP512/513
 - Added support for LTC2947
 - Added support for BEL PFE1100 and PFE3000
 - Various minor improvements and fixes
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiHPvMQj9QTOCiqgVyx8mb86fmYEFAl3dGjsACgkQyx8mb86f
 mYHdxxAAiMSLIy9+0F+bpDY9LPkASVTEBNKf50aCihS1HLfMcHxN4SaPU9xfoa64
 x8Oq3D0g3FVHoJYLjX0NFKx7w1u+B3Mud0bEKt09KHcJjQQFFSAwkGGyxpk28+IH
 XzLTYgYSqitYEmcT/AMsyNg1mRAyEJCmdF9yQyGqpirWkR1GxRYVmidZEgblWEZD
 IQYhy8omjyWOrJEHFT6oQ+Ki+kZkEQNCB22ies/R4qVC3u3zunnOK/xmT8abCSMh
 i+2lVpMyo/oo/loOWzRFwOYuQAXB072vpTwRRxo/77n4j2pVwg7Pb0AWrUMCR3Ec
 Nj3qd/phUMhL3iBDqBNy5VfeMiRGdGdnigHDMHQoJjYlyXI3Jc6MNFdluhm1VRSb
 +8aurQsS56XVfsk+FOr6wxD5q9vppIIS0RXlZ6TVD2RznEX5ta8GJ71y1FQHQ3FD
 KNp2aaAElx/Y6QAKswQ8BKA/138lTVFgZ4Pi4h9O4yptCzhxMOeo01Wlp+CsIQPF
 WCNvC2D8Lp5d9fU9z9Rr5e4iKDQLYBVEfkDQs/bL04h2+rPnddM9rJYcWE3rOSPk
 JZ6y3oj1iJxMF2eK5Q0x9qgUhmRURJMelFNshEukO7F+ismRiQPnXSOiPHJM+Qcj
 JGeSp8kPusOPGAt+/Zh4knKPGG41PfL03MMJQVwF5vQzXbwlDcs=
 =HNfe
 -----END PGP SIGNATURE-----

Merge tag 'hwmon-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - Add support for Texas Instruments TMP512/513

 - Add support for LTC2947

 - Add support for BEL PFE1100 and PFE3000

 - Various minor improvements and fixes

* tag 'hwmon-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  dell-smm-hwmon: Add documentation
  hwmon: (dell-smm) Add support for disabling automatic BIOS fan control
  hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.
  dt-bindings: hwmon: Add TMP512/513
  docs: hwmon: Document bel-pfe pmbus driver
  hwmon: (pmbus) add driver for BEL PFE1100 and PFE3000
  dt-bindings: hwmon: Add ltc2947 documentation
  hwmon: Add support for ltc2947
  hwmon: (ina3221) Add summation feature support
  hwmon: (tmp421) Allow reading at 2Hz instead of 0.5Hz
  hwmon: (w83793d) remove redundant assignment to variable res
  hwmon: (pmbus/ibm-cffps) Add version detection capability
  dt-bindings: hwmon: Document ibm,cffps compatible string
  hwmon: abituguru: make array probe_order static, makes object smaller
  hwmon: (applesmc) switch to using input device polling mode
  hwmon: (aspeed-pwm-tacho) Use devm_platform_ioremap_resource() in aspeed_pwm_tacho_probe()
  hwmon: (pmbus/ibm-cffps) Fix LED blink behavior
  hwmon: (pmbus/ibm-cffps) Switch LEDs to blocking brightness call
2019-11-27 09:58:49 -08:00
Linus Torvalds 00074a7007 power supply and reset changes for the v5.5 series
Drivers:
  * test_power: add support for current and charge_counter
  * cpcap-charger: improve charge calculation and limit default charge voltage
  * ab8500: convert to IIO
  * misc. small fixes all over drivers
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEE72YNB0Y/i3JqeVQT2O7X88g7+poFAl3dFBkACgkQ2O7X88g7
 +ppUPQ/7Bv3GRusMB9Z/nTlhTLyR68P5vOoQ7Axfhi9NUCIq3RRG/pKZkYKKits1
 5U9Z13pceDznmWvamPvNkhH6mVjS4JsLsJOSkp8op2DvptQpcrfs5t+XhBamWu/D
 pmy6FkhbFLhxSRshd3st1VcqPZNc9/PmoYaoBp397wDF+SKZxJ+wI/Fm6LQmqG/q
 SZv8eBKFmViyv+xYmXGJf2CZanxzZ0DZK2ZMYlp39XQcfOw90ImD5crZJcLlf9zQ
 HJV69JxurCDb0ovr2JfRjYtyfx8eqYFxSE5o6rqqNWIPGikQs3+TajovMuO5B0D0
 FmLxkgMeNAzK1CzccxKKh1qQi65T8Kdv+N6pgVgsR9wVfCmLsfYCeBrZb4PJv5GH
 hlJSZXxzYKgN00bD/7HA2l0hlUpIepQm0EtNCyjiPwGMVAHr8MerCfHwbzr5oWfq
 h1G3hGW9OOm1BwVvScff08UdL2xI6A7Aa7lLXqCkwM3oXhdFPAmr3qiv0Rw8wVNS
 /LY1HiQ2jldWgdVPdSMvPoLqxdfebz/Ro0J7do2amPGj/ebh6H7GvUVIxX/8cNZe
 iz22kzoJXW+k9173FGNZA+4Ccf49XdplFn2uinX9TsNCf4XCKcyWq+3aPczQ6zSl
 ZPqGn4mOpjRLm3xl/DbOOWXpNqFszVHhhX4G/WAMB8RMseFfelw=
 =iHhO
 -----END PGP SIGNATURE-----

Merge tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply

Pull power supply and reset updates from Sebastian Reichel:

 - test_power: add support for current and charge_counter

 - cpcap-charger: improve charge calculation and limit default charge
   voltage

 - ab8500: convert to IIO

 - misc small fixes all over drivers

* tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (29 commits)
  power: supply: bd70528: Add MODULE_ALIAS to allow module auto loading
  power: supply: ab8500_charger: Fix inconsistent IS_ERR and PTR_ERR
  power: supply: cpcap-charger: cpcap_charger_voltage_to_regval() can be static
  power: supply: cpcap-battery: Add basic coulomb counter calibrate support
  power: supply: cpcap-battery: Read and save integrator register CCI
  power: supply: cpcap-battery: Simplify short term power average calculation
  power: supply: cpcap-battery: Simplify coulomb counter calculation with div_s64
  power: supply: cpcap-battery: Move coulomb counter units per lsb to ddata
  power: supply: cpcap-charger: Allow changing constant charge voltage
  power: supply: cpcap-battery: Fix handling of lowered charger voltage
  power: supply: cpcap-charger: Improve battery detection
  power: supply: cpcap-battery: Check voltage before orderly_poweroff
  power: supply: cpcap-charger: Limit voltage to 4.2V for battery
  power: supply: ab8500: Handle invalid IRQ from platform_get_irq_byname()
  power: supply: ab8500_fg: Do not free non-requested IRQs in probe's error path
  power: supply: ab8500: Cleanup probe in reverse order
  power: reset: at91: fix __le32 cast in reset code
  power: supply: abx500_chargalg: Fix code indentation
  mfd: Switch the AB8500 GPADC to IIO
  iio: adc: New driver for the AB8500 GPADC
  ...
2019-11-27 09:55:39 -08:00
Giovanni Mascellani afe45277ad hwmon: (dell-smm) Add support for disabling automatic BIOS fan control
This patch exports standard hwmon pwmX_enable sysfs attribute for
enabling or disabling automatic fan control by BIOS. Standard value
"1" is for disabling automatic BIOS fan control and value "2" for
enabling.

By default BIOS auto mode is enabled by laptop firmware.

When BIOS auto mode is enabled, custom fan speed value (set via hwmon
pwmX sysfs attribute) is overwritten by SMM in few seconds and
therefore any custom settings are without effect. So this is reason
why implementing option for disabling BIOS auto mode is needed.

So finally this patch allows kernel to set and control fan speed on
laptops, but it can be dangerous (like setting speed of other fans).

The SMM commands to enable or disable automatic fan control are not
documented and are not the same on all Dell laptops. Therefore a
whitelist is used to send the correct codes only on laptopts for which
they are known.

This patch was originally developed by Pali Rohár; later Giovanni
Mascellani implemented the whitelist.

Signed-off-by: Giovanni Mascellani <gio@debian.org>
Co-Developed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://lore.kernel.org/r/20191122101519.1246458-1-gio@debian.org
[groeck: Fixed checkpatch warnings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-22 20:08:58 -08:00
Eric Tremblay 59dfa75e5d hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.
TI's TMP512/513 are I2C/SMBus system monitor chips. These chips
monitor the supply voltage, supply current, power consumption
and provide one local and up to three (TMP513) remote temperature sensors.

It has been tested using a TI TMP513 development kit (TMP513EVM)

Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
Link: https://lore.kernel.org/r/20191112223001.20844-3-etremblay@distech-controls.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-21 21:26:40 -08:00
Tao Ren 626bb2f3fb hwmon: (pmbus) add driver for BEL PFE1100 and PFE3000
Add "bel-pfe" pmbus driver to support hardware monitoring for BEL PFE1100
and PFE3000 power supplies.

Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20191029182054.32279-2-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Nuno Sá 9f90fd652b hwmon: Add support for ltc2947
The ltc2947 is a high precision power and energy monitor with an
internal sense resistor supporting up to +/- 30A. Three internal no
Latency ADCs ensure accurate measurement of voltage and current, while
high-bandwidth analog multiplication of voltage and current provides
accurate power measurement in a wide range of applications. Internal or
external clocking options enable precise charge and energy measurements.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191021154115.319073-1-nuno.sa@analog.com
[groeck: Removed unnecessary checks when reading temperature and energy;
	 PAGE{0,1} -> LTC2947_PAGE_{0,1}]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Nicolin Chen 2057bdfb71 hwmon: (ina3221) Add summation feature support
This patch implements the summation feature of INA3221, mainly the
SCC (enabling) and SF (warning flag) bits of MASK_ENABLE register,
INA3221_SHUNT_SUM (summation of shunt voltages) register, and the
INA3221_CRIT_SUM (its critical alert setting) register.

Although the summation feature allows user to select which channels
to be added to the result, as an initial support, this patch simply
selects all channels by default, with one only condition: all shunt
resistor values need to be the same. This is because the summation
of current channels can be only accurately calculated, using shunt
voltage sum register, if all shunt resistors are equivalent.

Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20191016235702.22039-1-nicoleotsuka@gmail.com
[groeck: summation->sum in documentation and label]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Kyle Roeschley 5ff02752b3 hwmon: (tmp421) Allow reading at 2Hz instead of 0.5Hz
Our driver configures the device to read at 2Hz, but then only allows the
user to read cached temp values at up to 0.5Hz. Let's allow users to read
as quickly as we do.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Link: https://lore.kernel.org/r/20191014140310.7438-1-kyle.roeschley@ni.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Colin Ian King 58a24b5241 hwmon: (w83793d) remove redundant assignment to variable res
The variable res is being initialized with a value that
is never read and is being re-assigned a little later on. The
assignment is redundant and hence can be removed.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191011170215.11539-1-colin.king@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Eddie James da806a1777 hwmon: (pmbus/ibm-cffps) Add version detection capability
Some systems may plug in either version 1 or version 2 of the IBM common
form factor power supply. Add a version-less compatibility string that
tells the driver to try and detect which version of the power supply is
connected.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1570648262-25383-3-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Colin Ian King 16f7f3bccb hwmon: abituguru: make array probe_order static, makes object smaller
Don't populate the array probe_order on the stack but instead make it
static. Makes the object code smaller by 94 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  41473	  13448	    320	  55241	   d7c9	drivers/hwmon/abituguru.o

After:
   text	   data	    bss	    dec	    hex	filename
  41315	  13512	    320	  55147	   d76b	drivers/hwmon/abituguru.o

(gcc version 9.2.1, amd64)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191006145231.24022-1-colin.king@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Dmitry Torokhov 58d5aa5c75 hwmon: (applesmc) switch to using input device polling mode
Now that instances of input_dev support polling mode natively,
we no longer need to create input_polled_dev instance.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20191002214345.GA108728@dtor-ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:18 -08:00
Markus Elfring 7b10e17067 hwmon: (aspeed-pwm-tacho) Use devm_platform_ioremap_resource() in aspeed_pwm_tacho_probe()
Simplify this function implementation by using a known wrapper function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/cd5bab7b-9333-2a43-bcf0-a47bbbe719eb@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:18 -08:00
Eddie James 92b39ad440 hwmon: (pmbus/ibm-cffps) Fix LED blink behavior
The LED blink_set function incorrectly did not tell the PSU LED to blink
if brightness was LED_OFF. Fix this, and also correct the LED_OFF
command data, which should give control of the LED back to the PSU
firmware. Also prevent I2C failures from getting the driver LED state
out of sync and add some dev_dbg statements.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20191106200106.29519-3-eajames@linux.ibm.com
Fixes: ef9e1cdf41 ("hwmon: (pmbus/cffps) Add led class device for power supply fault led")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:36:37 -08:00
Eddie James 9861ff954c hwmon: (pmbus/ibm-cffps) Switch LEDs to blocking brightness call
Since i2c_smbus functions can sleep, the brightness setting function
for this driver must be the blocking version to avoid scheduling while
atomic.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20191106200106.29519-2-eajames@linux.ibm.com
Fixes: ef9e1cdf41 ("hwmon: (pmbus/cffps) Add led class device for power supply fault led")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:34:06 -08:00
Nicolin Chen 2ccb4f16d0 hwmon: (ina3221) Fix read timeout issue
After introducing "samples" to the calculation of wait time, the
driver might timeout at the regmap_field_read_poll_timeout call,
because the wait time could be longer than the 100000 usec limit
due to a large "samples" number.

So this patch sets the timeout limit to 2 times of the wait time
in order to fix this issue.

Fixes: 5c090abf94 ("hwmon: (ina3221) Add averaging mode support")
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20191022005922.30239-1-nicoleotsuka@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-10-28 18:46:55 -07:00
Arnd Bergmann b6dfb2477f compat_ioctl: move WDIOC handling into wdt drivers
All watchdog drivers implement the same set of ioctl commands, and
fortunately all of them are compatible between 32-bit and 64-bit
architectures.

Modern drivers always go through drivers/watchdog/wdt.c as an abstraction
layer, but older ones implement their own file_operations on a character
device for this.

Move the handling from fs/compat_ioctl.c into the individual drivers.

Note that most of the legacy drivers will never be used on 64-bit
hardware, because they are for an old 32-bit SoC implementation, but
doing them all at once is safer than trying to guess which ones do
or do not need the compat_ioctl handling.

Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-10-23 17:23:46 +02:00
amy.shih 6fc28b7e0a hwmon: (nct7904) Fix the incorrect value of vsen_mask & tcpu_mask & temp_mode in nct7904_data struct.
Voltage sensors overlap with external temperature sensors. Detect
the multi-function of voltage, thermal diode, thermistor and
reserved from register VT_ADC_MD_REG to set value of vsen_mask &
tcpu_mask & temp_mode in nct7904_data struct. If the value is
reserved, needs to disable the vsen_mask & tcpu_mask.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20191014082451.2895-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-10-20 09:22:48 -07:00
Linus Walleij d17e86cb16 hwmon: ab8500: Convert to IIO ADC
This switches the AB8500 hardware monitor driver to using
the standard IIO ADC channel lookup and conversion routines.

Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-10-18 19:37:08 +01:00
amy.shih 6bbfdcbc8e hwmon: (nct7904) Add array fan_alarm and vsen_alarm to store the alarms in nct7904_data struct.
SMI# interrupt for fan and voltage is Two-Times Interrupt Mode.
Fan or voltage exceeds high limit or going below low limit,
it will causes an interrupt if the previous interrupt has been
reset by reading all the interrupt Status Register. Thus, add the
array fan_alarm and vsen_alarm to store the alarms for all of the
fan and voltage sensors.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190919030205.11440-1-Amy.Shih@advantech.com.tw
Fixes: 486842db3b ("hwmon: (nct7904) Add extra sysfs support for fan, voltage and temperature.")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-10-02 06:42:48 -07:00
amy.shih 539ad001d1 hwmon: (nct7904) Fix the incorrect value of vsen_mask in nct7904_data struct
Voltage sensors overlap with external temperature sensors. Detect
the multi-function of voltage, thermal diode and thermistor from
register VT_ADC_MD_REG to set value of vsen_mask in nct7904_data
struct.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190918084801.9859-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-10-02 06:34:26 -07:00
Linus Torvalds 5c6bd5de3c Main MIPS changes for v5.4:
- boot_mem_map is removed, providing a nice cleanup made possible by the
   recent removal of bootmem.
 
 - Some fixes to atomics, in general providing compiler barriers for
   smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
   MIPS32 systems using cmpxchg64().
 
 - Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
   Frascino.
 
 - Removal of undefined behavior in set_io_port_base(), fixing the
   behavior of some MIPS kernel configurations when built with recent
   clang versions.
 
 - Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
 
 - pte_special() is now supported for some configurations, allowing among
   other things generic fast GUP to be used.
 
 - Miscellaneous fixes & cleanups.
 
 And platform specific changes:
 
 - Major improvements to Ingenic SoC support from Paul Cercueil, mostly
   enabled by the inclusion of the new TCU (timer-counter unit) drivers
   he's spent a very patient year or so working on. Plus some fixes for
   X1000 SoCs from Zhou Yanjie.
 
 - Netgear R6200 v1 systems are now supported by the bcm47xx platform.
 
 - DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
 -----BEGIN PGP SIGNATURE-----
 
 iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
 b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
 4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
 =lWlM
 -----END PGP SIGNATURE-----

Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

Pull MIPS updates from Paul Burton:
 "Main MIPS changes:

   - boot_mem_map is removed, providing a nice cleanup made possible by
     the recent removal of bootmem.

   - Some fixes to atomics, in general providing compiler barriers for
     smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
     or MIPS32 systems using cmpxchg64().

   - Conversion to the new generic VDSO infrastructure courtesy of
     Vincenzo Frascino.

   - Removal of undefined behavior in set_io_port_base(), fixing the
     behavior of some MIPS kernel configurations when built with recent
     clang versions.

   - Initial MIPS32 huge page support, functional on at least Ingenic
     SoCs.

   - pte_special() is now supported for some configurations, allowing
     among other things generic fast GUP to be used.

   - Miscellaneous fixes & cleanups.

  And platform specific changes:

   - Major improvements to Ingenic SoC support from Paul Cercueil,
     mostly enabled by the inclusion of the new TCU (timer-counter unit)
     drivers he's spent a very patient year or so working on. Plus some
     fixes for X1000 SoCs from Zhou Yanjie.

   - Netgear R6200 v1 systems are now supported by the bcm47xx platform.

   - DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"

* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
  MIPS: Detect bad _PFN_SHIFT values
  MIPS: Disable pte_special() for MIPS32 with RiXi
  MIPS: ralink: deactivate PCI support for SOC_MT7621
  mips: compat: vdso: Use legacy syscalls as fallback
  MIPS: Drop Loongson _CACHE_* definitions
  MIPS: tlbex: Remove cpu_has_local_ebase
  MIPS: tlbex: Simplify r3k check
  MIPS: Select R3k-style TLB in Kconfig
  MIPS: PCI: refactor ioc3 special handling
  mips: remove ioremap_cachable
  mips/atomic: Fix smp_mb__{before,after}_atomic()
  mips/atomic: Fix loongson_llsc_mb() wreckage
  mips/atomic: Fix cmpxchg64 barriers
  MIPS: Octeon: remove duplicated include from dma-octeon.c
  firmware: bcm47xx_nvram: Allow COMPILE_TEST
  firmware: bcm47xx_nvram: Correct size_t printf format
  MIPS: Treat Loongson Extensions as ASEs
  MIPS: Remove dev_err() usage after platform_get_irq()
  MIPS: dts: mscc: describe the PTP ready interrupt
  MIPS: dts: mscc: describe the PTP register range
  ...
2019-09-22 09:30:30 -07:00
Linus Torvalds 1f7d290a72 Driver core patches for 5.4-rc1
Here is the big driver core update for 5.4-rc1.
 
 There was a bit of a churn in here, with a number of core and OF
 platform patches being added to the tree, and then after much discussion
 and review and a day-long in-person meeting, they were decided to be
 reverted and a new set of patches is currently being reviewed on the
 mailing list.
 
 Other than that churn, there are two "persistent" branches in here that
 other trees will be pulling in as well during the merge window.  One
 branch to add support for drivers to have the driver core automatically
 add sysfs attribute files when a driver is bound to a device so that the
 driver doesn't have to manually do it (and then clean it up, as it
 always gets it wrong).
 
 There's another branch in here for generic lookup helpers for the driver
 core that lots of busses are starting to use.  That's the majority of
 the non-driver-core changes in this patch series.
 
 There's also some on-going debugfs file creation cleanup that has been
 slowly happening over the past few releases, with the goal to hopefully
 get that done sometime next year.
 
 All of these have been in linux-next for a while now with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIVHA8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymEVwCfRPxQHQplI6ZR6h0jPscLSaZnaFIAn1a+rjO2
 EFuuXJ5Ip72F5Ch9AW3G
 =r8lH
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg Kroah-Hartman:
 "Here is the big driver core update for 5.4-rc1.

  There was a bit of a churn in here, with a number of core and OF
  platform patches being added to the tree, and then after much
  discussion and review and a day-long in-person meeting, they were
  decided to be reverted and a new set of patches is currently being
  reviewed on the mailing list.

  Other than that churn, there are two "persistent" branches in here
  that other trees will be pulling in as well during the merge window.
  One branch to add support for drivers to have the driver core
  automatically add sysfs attribute files when a driver is bound to a
  device so that the driver doesn't have to manually do it (and then
  clean it up, as it always gets it wrong).

  There's another branch in here for generic lookup helpers for the
  driver core that lots of busses are starting to use. That's the
  majority of the non-driver-core changes in this patch series.

  There's also some on-going debugfs file creation cleanup that has been
  slowly happening over the past few releases, with the goal to
  hopefully get that done sometime next year.

  All of these have been in linux-next for a while now with no reported
  issues"

[ Note that the above-mentioned generic lookup helpers branch was
  already brought in by the LED merge (commit 4feaab05dc) that had
  shared it.

  Also note that that common branch introduced an i2c bug due to a bad
  conversion, which got fixed here. - Linus ]

* tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (49 commits)
  coccinelle: platform_get_irq: Fix parse error
  driver-core: add include guard to linux/container.h
  sysfs: add BIN_ATTR_WO() macro
  driver core: platform: Export platform_get_irq_optional()
  hwmon: pwm-fan: Use platform_get_irq_optional()
  driver core: platform: Introduce platform_get_irq_optional()
  Revert "driver core: Add support for linking devices during device addition"
  Revert "driver core: Add edit_links() callback for drivers"
  Revert "of/platform: Add functional dependency link from DT bindings"
  Revert "driver core: Add sync_state driver/bus callback"
  Revert "of/platform: Pause/resume sync state during init and of_platform_populate()"
  Revert "of/platform: Create device links for all child-supplier depencencies"
  Revert "of/platform: Don't create device links for default busses"
  Revert "of/platform: Fix fn definitons for of_link_is_valid() and of_link_property()"
  Revert "of/platform: Fix device_links_supplier_sync_state_resume() warning"
  Revert "of/platform: Disable generic device linking code for PowerPC"
  devcoredump: fix typo in comment
  devcoredump: use memory_read_from_buffer
  of/platform: Disable generic device linking code for PowerPC
  device.h: Fix warnings for mismatched parameter names in comments
  ...
2019-09-18 10:04:39 -07:00
Linus Torvalds 7c672abc12 It's a somewhat calmer cycle for docs this time, as the churn of the mass
RST conversion is happily mostly behind us.
 
  - A new document on reproducible builds.
 
  - We finally got around to zapping the documentation for hardware support
    that was removed in 2004; one doesn't want to rush these things.
 
  - The usual assortment of fixes, typo corrections, etc.
 
 You'll still find a handful of annoying conflicts against other trees,
 mostly tied to the last RST conversions; resolutions are straightforward
 and the linux-next ones are good.
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
 flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
 jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
 dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
 l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
 Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
 051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
 =v4dp
 -----END PGP SIGNATURE-----

Merge tag 'docs-5.4' of git://git.lwn.net/linux

Pull documentation updates from Jonathan Corbet:
 "It's a somewhat calmer cycle for docs this time, as the churn of the
  mass RST conversion is happily mostly behind us.

   - A new document on reproducible builds.

   - We finally got around to zapping the documentation for hardware
     support that was removed in 2004; one doesn't want to rush these
     things.

   - The usual assortment of fixes, typo corrections, etc"

* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
  Documentation: kbuild: Add document about reproducible builds
  docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
  Documentation: Add "earlycon=sbi" to the admin guide
  doc🔒 remove reference to clever use of read-write lock
  devices.txt: improve entry for comedi (char major 98)
  docs: mtd: Update spi nor reference driver
  doc: arm64: fix grammar dtb placed in no attributes region
  Documentation: sysrq: don't recommend 'S' 'U' before 'B'
  mailmap: Update email address for Quentin Perret
  docs: ftrace: clarify when tracing is disabled by the trace file
  docs: process: fix broken link
  Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
  Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
  Documentation/arm/sa1100: Remove some obsolete documentation
  docs/zh_CN: update Chinese howto.rst for latexdocs making
  Documentation: virt: Fix broken reference to virt tree's index
  docs: Fix typo on pull requests guide
  kernel-doc: Allow anonymous enum
  Documentation: sphinx: Don't parse socket() as identifier reference
  Documentation: sphinx: Add missing comma to list of strings
  ...
2019-09-17 16:22:26 -07:00
Linus Torvalds 399eb9b6cb ARM: SoC driver updates for v5.4
The branch contains driver changes that are tightly
 connected to SoC specific code. Aside from smaller
 cleanups and bug fixes, here is a list of the notable
 changes.
 
 New device drivers:
 
 - The Turris Mox router has a new "moxtet" bus driver
   for its on-board pluggable extension bus. The
   same platform also gains a firmware driver.
 
 - The Samsung Exynos family gains a new Chipid driver
   exporting using the soc device sysfs interface
 
 - A similar socinfo driver for Qualcomm Snapdragon
   chips.
 
 - A firmware driver for the NXP i.MX DSP IPC protocol
   using shared memory and a mailbox
 
 Other changes:
 
 - The i.MX reset controller driver now supports the
   NXP i.MX8MM chip
 
 - Amlogic SoC specific drivers gain support for
   the S905X3 and A311D chips
 
 - A rework of the TI Davinci framebuffer driver to
   allow important cleanups in the platform code
 
 - A couple of device drivers for removed ARM SoC
   platforms are removed. Most of the removals were
   picked up by other maintainers, this contains
   whatever was left.
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJdf6SUAAoJEJpsee/mABjZAfwP/01bXBOlGVusNH2zuh8IUSHb
 //5sTdWpwa2ugRekLOJUOjo2p9Fu70yH6xr4RUHI0rcRjZA0xR3bZPx45gI8LRHQ
 tfb25LaKqfgZjWMCJ8due1Lh7B6ffOQukryMtM/LoiCtqsy7b6aThEKaLpM9/Owl
 t53o4wKaVQJK5He9JQom9NOZidkl7tYLHmDQTOXhX2UEA/i45vtfjdsEBvoFPbTx
 +bYvlqs+SWlpDJk29j+oBOeKadPF+TFboLDiUCxH44MC3OsH51zjtKVBRTtbNMkb
 ek/ci5x9hCeHcYSEigNq2EMzEln09Yxyvjk8U/jLiJ1h1kz3p5MjqJbVMF1rYXpe
 ALuAwinM8Zv2o5/UOCkiQTWq79PtpOKHZKpNBXkaJ8kyqBLMSy8Fs3hCvXrDnjnQ
 TC8jX7UBqHRV2rbQIYehAQAxTvcRgTbqusQGLkUJInlux6go57LoMYHPABpHftJV
 kRdVeT0KzdCz1pvQwyekIog5hPLNTBi4jw6eQcOgeENvAea1MJa8lMMfKcVbIdS0
 ZVvxLl+K6noEKAv5lSeHAzjXq+cQFr3zDCsWy351mJETDHmE8zjsaHN1SgbRYLEk
 ZqzNwUYaPYBis38g85qaY/TSsJrWJ+jP8u7s9HTw3Oywg8SRy5vtW177s00/9VOd
 PYZ2UpqUeX8cdvggqUUU
 =lxFi
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "This contains driver changes that are tightly connected to SoC
  specific code. Aside from smaller cleanups and bug fixes, here is a
  list of the notable changes.

  New device drivers:

   - The Turris Mox router has a new "moxtet" bus driver for its
     on-board pluggable extension bus. The same platform also gains a
     firmware driver.

   - The Samsung Exynos family gains a new Chipid driver exporting using
     the soc device sysfs interface

   - A similar socinfo driver for Qualcomm Snapdragon chips.

   - A firmware driver for the NXP i.MX DSP IPC protocol using shared
     memory and a mailbox

  Other changes:

   - The i.MX reset controller driver now supports the NXP i.MX8MM chip

   - Amlogic SoC specific drivers gain support for the S905X3 and A311D
     chips

   - A rework of the TI Davinci framebuffer driver to allow important
     cleanups in the platform code

   - A couple of device drivers for removed ARM SoC platforms are
     removed. Most of the removals were picked up by other maintainers,
     this contains whatever was left"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
  bus: uniphier-system-bus: use devm_platform_ioremap_resource()
  soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
  dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
  firmware: ti_sci: Allow for device shared and exclusive requests
  bus: imx-weim: remove incorrect __init annotations
  fbdev: remove w90x900/nuc900 platform drivers
  spi: remove w90x900 driver
  net: remove w90p910-ether driver
  net: remove ks8695 driver
  firmware: turris-mox-rwtm: Add sysfs documentation
  firmware: Add Turris Mox rWTM firmware driver
  dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
  bus: moxtet: fix unsigned comparison to less than zero
  bus: moxtet: remove set but not used variable 'dummy'
  ARM: scoop: Use the right include
  dt-bindings: power: add Amlogic Everything-Else power domains bindings
  soc: amlogic: Add support for Everything-Else power domains controller
  fbdev: da8xx: use resource management for dma
  fbdev: da8xx-fb: drop a redundant if
  fbdev: da8xx-fb: use devm_platform_ioremap_resource()
  ...
2019-09-16 15:52:38 -07:00
amy.shih 3b710d7ae5 hwmon: (nct7904) Fix incorrect SMI status register setting of LTD temperature and fan.
According to datasheet, the SMI status register setting of LTD
temperature is SMI_STS3, and the SMI status register setting
of fan is SMI_STS5 and SMI_STS6.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190912113300.4714-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-12 11:52:08 -07:00
Dan Robertson ffd96868ac hwmon: (shtc1) add support for the SHTC3 sensor
Add support for the Sensirion SHTC3 humidity and temperature sensor to
the shtc1 module.

Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Link: https://lore.kernel.org/r/20190905014554.21658-2-dan@dlrobertson.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-10 11:42:56 -07:00
Dan Robertson fdc7d8e829 hwmon: (shtc1) fix shtc1 and shtw1 id mask
Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to
retrieve the chip ID from the ID register. See section 5.7 of the shtw1
or shtc1 datasheet for details.

Fixes: 1a539d372e ("hwmon: add support for Sensirion SHTC1 sensor")
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com
[groeck: Reordered to be first in series and adjusted accordingly]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-10 11:42:22 -07:00
Iker Perez del Palomar Sustatxa 35cd180485 hwmon: (lm75) Aproximate sample times to data-sheet values
Current sample time values are over estimated, this patches applies
values closer to the ones defined in the data-sheets.

Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
[groeck: resolved conflicts; use default conversion times]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-04 11:06:47 -07:00
Wolfram Sang cf48d17623 hwmon: (w83793d) convert to use devm_i2c_new_dummy_device
And simplify the error handling.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190903181256.13450-4-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Wolfram Sang f64211151d hwmon: (w83792d) convert to use devm_i2c_new_dummy_device
And simplify the error handling.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190903181256.13450-3-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Wolfram Sang 358d207110 hwmon: (w83791d) convert to use devm_i2c_new_dummy_device
And simplify the error handling.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190903181256.13450-2-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
kbuild test robot 09fe787051 hwmon: (as370-hwmon) fix devm_platform_ioremap_resource.cocci warnings
Use devm_platform_ioremap_resource helper which wraps
 platform_get_resource() and devm_ioremap_resource() together.

Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci

Fixes: 658e687b4218 ("hwmon: Add Synaptics AS370 PVT sensor driver")
CC: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.1909030646180.3228@hadrien
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Guenter Roeck d7a85cde90 hwmon: (lm75) Add support for writing sampling period on PCT2075
For PCT7027, the sampling period is configured using a dedicated
register.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Guenter Roeck cee04a013a hwmon: (lm75) Add support for writing conversion time for TMP112
TMP112 uses an uncommon method to write the conversion time: its
configuration register is 16 bit wide, and the conversion time is
configured in its second byte.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Guenter Roeck 040b106ff8 hwmon: (lm75) Move updating the sample interval to its own function
We'll need per-chip handling for updating the sample interval.
To prepare for it, separate the code implementing it into its own
function.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Guenter Roeck 7db0db3f6c hwmon: (lm75) Support configuring the sample time for various chips
The conversion (sample) time is configurable for several chips supported
by the lm75 driver. With the necessary infrastructure in place, enable
this support for all chips using the configuration register for this
purpose.

DS1775:
	Conversion time:	187.5, 375, 750, 1500 ms
	Sensor resolution: 	9, 10, 11, 12 bit
DS75, STDS75:
	Conversion time:	150, 300, 600, 1200 ms
	Sensor resolution: 	9, 10, 11, 12 bit
DS7505:
	Conversion time:	25, 50, 100, 200 ms
	Sensor resolution: 	9, 10, 11, 12 bit
MCP980[0123]:
	Conversion time:	75, 150, 300, 600 ms
	Sensor resolution: 	9, 10, 11, 12 bit
TMP100, TMP101:
	Conversion time:	75, 150, 300, 600 ms
	Sensor resolution: 	9, 10, 11, 12 bit
TMP75, TMP105, TMP175, TMP275:
	Conversion time:	38, 75, 150, 300 ms
	Sensor resolution: 	9, 10, 11, 12 bit

While doing this, it became obvious that the masks and values to set
the converion (sample) time is similar for all those chips, and that
other chips with configurable sample times will need separate code anyway.
For that reason, replace the sample_set_masks and sample_clr_mask
configuration parameters with a single array and with a constant.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
amy.shih 4a2d78822f hwmon: (nct7904) Fix incorrect temperature limitation register setting of LTD.
According to kernel hwmon sysfs-interface documentation, temperature
critical max value, typically greater than corresponding temp_max values.
Thus, reads the LTD_HV_HL (LTD HIGH VALUE HIGH LIMITATION) and LTD_LV_HL
(LTD LOW VALUE HIGH LIMITATION) for case hwmon_temp_crit and
hwmon_temp_crit_hyst. Reads the LTD_HV_LL (HIGH VALUE LOW LIMITATION)
and LTD_LV_LL (LOW VALUE LOW LIMITATION) for case hwmon_temp_max
and hwmon_temp_max_hyst.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20850618155720.24857-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Jisheng Zhang 7548666e6f hwmon: Add Synaptics AS370 PVT sensor driver
Add a new driver for Synaptics AS370 PVT sensors. Currently, only
temperature is supported.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190827113259.4fb64a17@xhacker.debian
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Eddie James 2f8a855efe pmbus: (ibm-cffps) Add support for version 2 of the PSU
Version 2 of the PSU supports a second page of data and changes the
format of the FW version. Use the devicetree binding to differentiate
between the version the driver should use.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1567192263-15065-4-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Michal Simek bc34301b10 hwmon: (iio_hwmon) Enable power exporting from IIO
There is no reason why power channel shouldn't be exported as is done for
voltage, current, temperature and humidity.

Power channel is available on iio ina226 driver.

Sysfs IIO documentation for power attribute added by commit 7c6d5c7ee8
("iio: Documentation: Add missing documentation for power attribute")
is declaring that value is in mili-Watts but hwmon interface is expecting
value in micro-Watts that's why there is a need for mili-Watts to
micro-Watts conversion.

Tested on Xilinx ZCU102 board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/db71f5ae87e4521a2856a1be5544de0b6cede575.1566483741.git.michal.simek@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
John Wang edd2a4d660 hwmon: pmbus: Add Inspur Power System power supply driver
Add the driver to monitor Inspur Power System power supplies
with hwmon over pmbus.

This driver adds sysfs attributes for additional power supply data,
including vendor, model, part_number, serial number,
firmware revision, hardware revision, and psu mode(active/standby).

Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190819091509.29276-1-wangzqbj@inspur.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Max Staudt 06a1c69cf5 hwmon/ltc2990: Generalise DT to fwnode support
ltc2990 will now use device_property_read_u32_array() instead of
of_property_read_u32_array() - allowing the use of software nodes
via fwnode_create_software_node().

This allows code using i2c_new_device() to specify a default
measurement mode for the LTC2990 via fwnode_create_software_node().

Signed-off-by: Max Staudt <max@enpas.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20190819121618.16557-2-max@enpas.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Stefan Wahren 10b1f2a9d4 hwmon: (raspberrypi) update MODULE_AUTHOR() email address
The email address listed in MODULE_AUTHOR() will be disabled in the
near future. Replace it with my private one.

Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/1565720249-6549-2-git-send-email-wahrenst@gmx.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Iker Perez del Palomar Sustatxa 4b5be3c173 hwmon: (lm75) Modularize lm75_write and make hwmon_chip writable
* Create two separate functions to write into hwmon_temp and hwmon_chip.
* Call the functions from lm75_write.
* Make hwm_chip writable if the chip supports more than one sample time.

Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-5-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Iker Perez del Palomar Sustatxa 7f1a300f8a hwmon: (lm75) Add new fields into lm75_params_
The new fields are included to prepare the driver for next patch. The
fields are:

* *resolutions: Stores all the supported resolutions by the device.
* num_sample_times: Stores the number of possible sample times.
* *sample_times: Stores all the possible sample times to be set.
* sample_set_masks: The set_masks for the possible sample times
* sample_clr_mask: Clear mask to set the default sample time.

Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-4-iker.perez@codethink.co.uk
[groeck: Minor structure documentation fixes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Iker Perez del Palomar Sustatxa 58608cfee8 hwmon: (lm75) Create function from code to write into registers
Wrap the existing code to write configurations into registers in
a function.

Added error handling to the function.

Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-3-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Iker Perez del Palomar Sustatxa dcb1265387 hwmon: (lm75) Create structure to save all the configuration parameters.
* Add to lm75_data kind field to store the kind of device the driver is
  working with.
* Add an structure to store the configuration parameters of all the
  supported devices.
* Delete resolution_limits from lm75_data and include them in the structure
  described above.
* Add a pointer to the configuration parameters structure to be used as a
  reference to obtain the parameters.
* Delete switch-case approach to get the device configuration parameters.
* The structure is cleaner and easier to maintain.

Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-2-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
amy.shih 486842db3b hwmon: (nct7904) Add extra sysfs support for fan, voltage and temperature.
NCT-7904D also supports reading of channel limitation registers as well
as SMI status registers for fan, voltage and temperature monitoring.
It also supports reading the temperature sensor type (thermal diode,
thermistor, AMD SB-TSI or Intel PECI).

Add the following sysfs nodes:

-fan[1-*]_min
-fan[1-*]_alarm
-in[1-*]_min
-in[1-*]_max
-in[1-*]_alarm
-temp[1-*]_max
-temp[1-*]_max_hyst
-temp[1-*]_emergency
-temp[1-*]_emergency_hyst
-temp[1-*]_alarm
-temp[1-*]_type

Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190807013842.24451-1-Amy.Shih@advantech.com.tw
[groeck: Clarified description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Jean Delvare dbf5520511 hwmon: w83795: Fan control option isn't that dangerous
I have been using SENSORS_W83795_FANCTRL for several years and never
had any problem. When the driver was added, I had not tested that
part of the driver yet so I wanted to be super cautious, but time has
shown that it works just fine.

In the long run I even believe that we should drop the option and
enable the feature unconditionally. It doesn't do anything until the
user explicitly starts twiddling with sysfs attributes anyway.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20190806102123.3118bcc5@endymion
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Stephen Boyd f2ff7ceaa4 hwmon: (npcm750-pwm-fan) Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[groeck: Dropped jz4740-hwmon.c (driver is being removed)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Wang Shenran 6e4d91aa07 hwmon: (acpi_power_meter) Change log level for 'unsafe software power cap'
At boot time, the acpi_power_meter driver logs the following error level
message: "Ignoring unsafe software power cap". Having read about it from
a few sources, it seems that the error message can be quite misleading.

While the message can imply that Linux is ignoring the fact that the
system is operating in potentially dangerous conditions, the truth is
the driver found an ACPI_PMC object that supports software power
capping. The driver simply decides not to use it, perhaps because it
doesn't support the object.

The best solution is probably changing the log level from error to warning.
All sources I have found, regarding the error, have downplayed its
significance. There is not much of a reason for it to be on error level,
while causing potential confusions or misinterpretations.

Signed-off-by: Wang Shenran <shenran268@gmail.com>
Link: https://lore.kernel.org/r/20190724080110.6952-1-shenran268@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Björn Gerhart 29c7cb485b hwmon: (nct6775) Integrate new model nct6116
Add support for NCT6116D to nct6775 driver.

Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Grant McEwan c64fce7f2a hwmon: (adt7475) Convert to use hwmon_device_register_with_groups()
hwmon_device_register() is a deprecated function and produces a warning.

Converting the driver to use the hwmon_device_register_with_groups()
instead.

Signed-off-by: Grant McEwan <grant.mcewan@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20190721225530.28799-2-grant.mcewan@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Wolfram Sang 22e96ce318 hwmon: (w83781d) convert to i2c_new_dummy_device
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190722172611.3797-4-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Wolfram Sang 25d4016464 hwmon: (smm665) convert to i2c_new_dummy_device
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190722172611.3797-3-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Wolfram Sang 8f9508ebbf hwmon: (asb100) convert to i2c_new_dummy_device
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190722172611.3797-2-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Marcel Bocu 12163cfbfc hwmon: (k10temp) Add support for AMD family 17h, model 70h CPUs
It would seem like model 70h is behaving in the same way as model 30h,
so let's just add the new F3 PCI ID to the list of compatible devices.

Unlike previous Ryzen/Threadripper, Ryzen gen 3 processors do not need
temperature offsets anymore. This has been reported in the press and
verified on my Ryzen 3700X by checking that the idle temperature
reported by k10temp is matching the temperature reported by the
firmware.

Vicki Pfau sent an identical patch after I checked that no-one had
written this patch. I would have been happy about dropping my patch but
unlike for his patch series, I had already Cc:ed the x86 people and
they already reviewed the changes. Since Vicki has not answered to
any email after his initial series, let's assume she is on vacation
and let's avoid duplication of reviews from the maintainers and merge
my series. To acknowledge Vicki's anteriority, I added her S-o-b to
the patch.

v2, suggested by Guenter Roeck and Brian Woods:
  - rename from 71h to 70h

Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Tested-by: Marcel Bocu <marcel.p.bocu@gmail.com>

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: "Woods, Brian" <Brian.Woods@amd.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20190722174653.2391-1-marcel.p.bocu@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Robert Karszniewicz 3b07a702cc hwmon: (k8temp) update to use new hwmon registration API
Removes:
- hwmon_dev from k8temp_data struct, as that is now passed
  to callbacks, anyway.
- other k8temp_data struct fields, too.
- k8temp_update_device()

Also reduces binary size:
   text    data     bss     dec     hex filename
   4139    1448       0    5587    15d3 drivers/hwmon/k8temp.ko.bak
   3103    1220       0    4323    10e3 drivers/hwmon/k8temp.ko

Signed-off-by: Robert Karszniewicz <avoidr@firemail.cc>
Signed-off-by: Robert Karszniewicz <avoidr@riseup.net>
Link: https://lore.kernel.org/r/20190721120051.28064-1-avoidr@riseup.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Christophe JAILLET 59eedefbba hwmon: (pmbus/max31785) Remove a useless #define
There is a typo in MAX37185_NUM_FAN_PAGES. To be consistent, it should be
MAX31785_NUM_FAN_PAGES (1 and 7 switched).

At line 24, we already have:
   #define MAX31785_NR_FAN_PAGES		6
and MAX37185_NUM_FAN_PAGES seems to be unused.

It is likely that it is only a typo and/or a left-over.
So, axe it.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190721101553.20911-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Daniel Mack 557c7ffa2f hwmon: (lm75) add support for PCT2075
The NXP PCT2075 is largely compatible with other chips already supported
by the LM75 driver. It uses an 11-bit resolution and defaults to 100 ms
sampling period. The datasheet is here:

  https://www.nxp.com/docs/en/data-sheet/PCT2075.pdf

Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20190711124504.7580-2-daniel@zonque.org
[groeck: Documentation update]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Guenter Roeck 2c9d5b5e32 hwmon: Remove ads1015 driver
A driver for ADS1015 with more functionality is available in the iio
subsystem.

Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.

Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Wenwen Wang e027a2dea5 hwmon (coretemp) Fix a memory leak bug
In coretemp_init(), 'zone_devices' is allocated through kcalloc().
However, it is not deallocated in the following execution if
platform_driver_register() fails, leading to a memory leak. To fix this
issue, introduce the 'outzone' label to free 'zone_devices' before
returning the error.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Link: https://lore.kernel.org/r/1566248402-6538-1-git-send-email-wenwen@cs.uga.edu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-08-31 08:04:57 -07:00
Guenter Roeck 7d82fcc9d9 hwmon: (lm75) Fix write operations for negative temperatures
Writes into limit registers fail if the temperature written is negative.
The regmap write operation checks the value range, regmap_write accepts
an unsigned int as parameter, and the temperature value passed to
regmap_write is kept in a variable declared as long. Negative values
are converted large unsigned integers, which fails the range check.
Fix by type casting the temperature to u16 when calling regmap_write().

Cc: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Fixes: e65365fed8 ("hwmon: (lm75) Convert to use regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-08-31 08:04:57 -07:00
Bartosz Golaszewski 6f8c8f3c31 hwmon: pmbus: ucd9000: remove unneeded include
Build bot reports the following build issue after commit 9091373ab7
("gpio: remove less important #ifdef around declarations):

   In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:576:1: error: redefinition of 'gpiochip_add_pin_range'
    gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
    ^~~~~~~~~~~~~~~~~~~~~~
   In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
   include/linux/gpio.h:245:1: note: previous definition of 'gpiochip_add_pin_range' was here
    gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
    ^~~~~~~~~~~~~~~~~~~~~~
   In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:583:1: error: redefinition of 'gpiochip_add_pingroup_range'
    gpiochip_add_pingroup_range(struct gpio_chip *chip,
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~
   In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
   include/linux/gpio.h:254:1: note: previous definition of 'gpiochip_add_pingroup_range' was here
    gpiochip_add_pingroup_range(struct gpio_chip *chip,
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~
   In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:591:1: error: redefinition of 'gpiochip_remove_pin_ranges'
    gpiochip_remove_pin_ranges(struct gpio_chip *chip)
    ^~~~~~~~~~~~~~~~~~~~~~~~~~
   In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
   include/linux/gpio.h:263:1: note: previous definition of 'gpiochip_remove_pin_ranges' was here
    gpiochip_remove_pin_ranges(struct gpio_chip *chip)

This is caused by conflicting defines from linux/gpio.h and
linux/gpio/driver.h. Drivers should not include both the legacy and
the new API headers. This driver doesn't even use linux/gpio.h so
remove it.

Reported-by: kbuild test robot <lkp@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190808080144.6183-1-brgl@bgdev.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-08-31 08:04:57 -07:00
Thierry Reding 6e7e5c7fbc hwmon: pwm-fan: Use platform_get_irq_optional()
The PWM fan interrupt is optional, so we don't want an error message in
the kernel log if it wasn't specified.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://lore.kernel.org/r/20190828083411.2496-2-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-28 22:52:30 +02:00
Sudeep Holla 6a55331c87 firmware: arm_scmi: Drop async flag in sensor_ops->reading_get
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. Ideally we should be able to read that flag
and use asynchronous reads for any sensors with that attribute set.

In order to add that support, let's drop the async flag passed to
sensor_ops->reading_get and dynamically switch between sync and async
flags based on the attributes as provided by the firmware.

Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2019-08-12 12:23:00 +01:00
Iker Perez del Palomar Sustatxa a95a4f3f27 hwmon: (lm75) Fixup tmp75b clr_mask
The configuration register of the tmp75b sensor is 16bit long, however
the first byte is reserved, so there is not no need to take care of it.

Because the order of the bytes is little endian and it is only necessary
to write one byte, the desired bits must be shifted into a 8 bit range.

Fixes: 39abe9d88b ("hwmon: (lm75) Add support for TMP75B")
Cc: stable@vger.kernel.org
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190801075324.4638-1-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-08-07 14:50:49 -07:00
Guenter Roeck 38ada2f406 hwmon: (nct7802) Fix wrong detection of in4 presence
The code to detect if in4 is present is wrong; if in4 is not present,
the in4_input sysfs attribute is still present.

In detail:

- Ihen RTD3_MD=11 (VSEN3 present), everything is as expected (no bug).
- If we have RTD3_MD!=11 (no VSEN3), we unexpectedly have a in4_input
  file under /sys and the "sensors" command displays in4_input.
  But as expected, we have no in4_min, in4_max, in4_alarm, in4_beep.

Fix is_visible function to detect and report in4_input visibility
as expected.

Reported-by: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: stable@vger.kernel.org
Fixes: 3434f37835 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-08-07 14:49:46 -07:00
Mauro Carvalho Chehab ccf988b66d docs: i2c: convert to ReST and add to driver-api bookset
Convert each file at I2C subsystem, renaming them to .rst and
adding to the driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2019-07-31 13:25:27 -06:00
Paul Cercueil d202742058
hwmon: Drop obsolete JZ4740 driver
The JZ4740 boards now use the iio-hwmon driver.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
2019-07-30 10:41:54 -07:00
Björn Gerhart f3d43e2e45 hwmon: (nct6775) Fix register address and added missed tolerance for nct6106
Fixed address of third NCT6106_REG_WEIGHT_DUTY_STEP, and
added missed NCT6106_REG_TOLERANCE_H.

Fixes: 6c009501ff ("hwmon: (nct6775) Add support for NCT6102D/6106D")
Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-21 19:18:45 -07:00
Lei YU 211186cae1 hwmon: (occ) Fix division by zero issue
The code in occ_get_powr_avg() invokes div64_u64() without checking the
divisor. In case the divisor is zero, kernel gets an "Division by zero
in kernel" error.

Check the divisor and make it return 0 if the divisor is 0.

Fixes: c10e753d43 ("hwmon (occ): Add sensor types and versions")
Signed-off-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1562813088-23708-1-git-send-email-mine260309@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-21 19:18:45 -07:00
Linus Torvalds 8362fd64f0 ARM: SoC-related driver updates
Various driver updates for platforms and a couple of the small driver
 subsystems we merge through our tree:
 
  - A driver for SCU (system control) on NXP i.MX8QXP
  - Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
  - Qualcomm PM support for MSM8998
  - Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
  - Reset controller support for Bitmain BM1880
  - TI SCI (System Control Interface) support for CPU control on AM654
    processors
  - More TI sysc refactoring and rework
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl0yK3YPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3WdUQAJEFRzY4+8VfsUspKmGwzHsrk7t1038JUEDE
 VL3yYlvSGeHg5a58AI5PCR5ZCsyPK7Yw9cAcYexd0frFR7BCwKWrjqem0Lb5ovdK
 CYM517DRtYPSBMF08Xw4pbZlT0yg65F1e9cf6BlUpkUZ6lJn4gUy8Y4BE6Aw/zuF
 QKtQNs6Q8BUZqS3uoOpJ/PY4JiUmLPQPO4Lry7Lud8Z7qgArCC326paC3wwqjLoC
 TpoMqb6izt7Vzo4BtTo5TUCyiEFZDlb/thhDySVlYRE7DQJusHBvRO9qgjI2ahOo
 1/935q1fJO7S6+Yvc8DIzrD/DrIUOvOshi31F/J6iWKkQkTUxtQwsVReZKaiOfSD
 fYxNVCgTcMS6ailKQSMQ0SYgXDa2gWdV3tS9XU8qML3tnDthi1nDmZks0QAAnFPS
 bXRcWGtgqeQJ+QJ7yyKrsD9POeaq3Hc5/f1DN34H//Cyn0ip/fD6fkLCMIfUDwmu
 TmO2Mnj6/fG/iBK+ToF+DaJ0/u3RiV2MC2vCE+0m3cVI9jtq9iA1y3UlmoaKUhhC
 t9znA+u8/Jc5S2zNQriI2Ja5q8nKfihL7Jf68ENvGzLc7YuAqP6yx1LMg1g6Wshc
 nLT+kHOF6DCUC3W7a8VuNyaxCwVtTbNTti+nvQVOmV6eaGiD5vzpXkHBWMbOJ7Lh
 YOBwGyb4
 =ek+j
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms and a couple of the small driver
  subsystems we merge through our tree:

   - A driver for SCU (system control) on NXP i.MX8QXP

   - Qualcomm Always-on Subsystem messaging driver (AOSS QMP)

   - Qualcomm PM support for MSM8998

   - Support for a newer version of DRAM PHY driver for Broadcom (DPFE)

   - Reset controller support for Bitmain BM1880

   - TI SCI (System Control Interface) support for CPU control on AM654
     processors

   - More TI sysc refactoring and rework"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
  reset: remove redundant null check on pointer dev
  soc: rockchip: work around clang warning
  dt-bindings: reset: imx7: Fix the spelling of 'indices'
  soc: imx: Add i.MX8MN SoC driver support
  soc: aspeed: lpc-ctrl: Fix probe error handling
  soc: qcom: geni: Add support for ACPI
  firmware: ti_sci: Fix gcc unused-but-set-variable warning
  firmware: ti_sci: Use the correct style for SPDX License Identifier
  soc: imx8: Use existing of_root directly
  soc: imx8: Fix potential kernel dump in error path
  firmware/psci: psci_checker: Park kthreads before stopping them
  memory: move jedec_ddr.h from include/memory to drivers/memory/
  memory: move jedec_ddr_data.c from lib/ to drivers/memory/
  MAINTAINERS: Remove myself as qcom maintainer
  soc: aspeed: lpc-ctrl: make parameter optional
  soc: qcom: apr: Don't use reg for domain id
  soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
  memory: tegra: Fix -Wunused-const-variable
  firmware: tegra: Early resume BPMP
  soc/tegra: Select pinctrl for Tegra194
  ...
2019-07-19 17:13:56 -07:00
Linus Torvalds 97ff4ca46d Char / Misc driver patches for 5.3-rc1
Here is the "large" pull request for char and misc and other assorted
 smaller driver subsystems for 5.3-rc1.
 
 It seems that this tree is becoming the funnel point of lots of smaller
 driver subsystems, which is fine for me, but that's why it is getting
 larger over time and does not just contain stuff under drivers/char/ and
 drivers/misc.
 
 Lots of small updates all over the place here from different driver
 subsystems:
   - habana driver updates
   - coresight driver updates
   - documentation file movements and updates
   - Android binder fixes and updates
   - extcon driver updates
   - google firmware driver updates
   - fsi driver updates
   - smaller misc and char driver updates
   - soundwire driver updates
   - nvmem driver updates
   - w1 driver fixes
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXmoQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ylV9wCgyJGbpPch8v/ecrZGFHYS4sIMexIAoMco3zf6
 wnqFmXiz1O0tyo1sgV9R
 =7sqO
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char / misc driver updates from Greg KH:
 "Here is the "large" pull request for char and misc and other assorted
  smaller driver subsystems for 5.3-rc1.

  It seems that this tree is becoming the funnel point of lots of
  smaller driver subsystems, which is fine for me, but that's why it is
  getting larger over time and does not just contain stuff under
  drivers/char/ and drivers/misc.

  Lots of small updates all over the place here from different driver
  subsystems:
   - habana driver updates
   - coresight driver updates
   - documentation file movements and updates
   - Android binder fixes and updates
   - extcon driver updates
   - google firmware driver updates
   - fsi driver updates
   - smaller misc and char driver updates
   - soundwire driver updates
   - nvmem driver updates
   - w1 driver fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (188 commits)
  coresight: Do not default to CPU0 for missing CPU phandle
  dt-bindings: coresight: Change CPU phandle to required property
  ocxl: Allow contexts to be attached with a NULL mm
  fsi: sbefifo: Don't fail operations when in SBE IPL state
  coresight: tmc: Smatch: Fix potential NULL pointer dereference
  coresight: etm3x: Smatch: Fix potential NULL pointer dereference
  coresight: Potential uninitialized variable in probe()
  coresight: etb10: Do not call smp_processor_id from preemptible
  coresight: tmc-etf: Do not call smp_processor_id from preemptible
  coresight: tmc-etr: alloc_perf_buf: Do not call smp_processor_id from preemptible
  coresight: tmc-etr: Do not call smp_processor_id() from preemptible
  docs: misc-devices: convert files without extension to ReST
  fpga: dfl: fme: align PR buffer size per PR datawidth
  fpga: dfl: fme: remove copy_to_user() in ioctl for PR
  fpga: dfl-fme-mgr: fix FME_PR_INTFC_ID register address.
  intel_th: msu: Start read iterator from a non-empty window
  intel_th: msu: Split sgt array and pointer in multiwindow mode
  intel_th: msu: Support multipage blocks
  intel_th: pci: Add Ice Lake NNPI support
  intel_th: msu: Fix single mode with disabled IOMMU
  ...
2019-07-11 15:34:05 -07:00
Linus Torvalds 64b08df460 hwmon updates for v5.3
New drivers for Infineon PXE1610 and IRPS5401
 Minor improvements, cleanup, and fixes in several drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJdJNpEAAoJEMsfJm/On5mBjlkP/1DEAEtL6pJYyl0zmyR3QrUN
 CAkSvvH46ZFGLbZb/ZC3XuXTaBbxFmZxeZP0NLSoOh45zmNoo0IjPzmSBHpm9R+7
 ENZBLlMhtbR3M7zJO5kEb5kgOpnzf46KqEfOi72J51lZx+aabepSfkvzV1Zqf6TY
 PjuXwYG+VhhBobpwVNe2qixoQcHxhKbhheYvwbvfVjCA8YFqa08MkzbXjqHGcGwP
 mNKko/okRlLf1Qqq4rONlfixfO6rorKKN1oiDihFFRrNmJoT5n92jGaB+RLx2sHY
 pC8iHrOCnbe8iXXKYg8cwEVZ8OKUDfOSGL3RX2yVk6ZF7B13QZjqX7t437h3hAyD
 i0rWUyolKxwapAr2yUgO8QhHun6Zx/oOzpBPdGIdy0yhsbas9f9e5unGm9rSEWHh
 2aIMUED5YKtXqdujos05AYaw9GgQVPEbr16xkjU8DGc/qtWrWUFeER0dJDNDnduO
 yLl9yDwwq0bSoSEg54bA6ib4CPHyKtD8ZNrYDfGiTMO9xZqrwWssFMguvYnWbuNZ
 cAh6lEQODL5bhg4vGIMfqt3Ub7EoTzjCCOnQRrOU4ERbxazaB56+A2VyYv+7LwLd
 sPfxldSMjyUYrnyDk+WQkTgRl0WsV/Sr4FS6Z4NOjZWyGoTCsjB8Z/m/5eEydIas
 VbeuAQEKoxvvJOWaRu00
 =G/oG
 -----END PGP SIGNATURE-----

Merge tag 'hwmon-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - New drivers for Infineon PXE1610 and IRPS5401

 - Minor improvements, cleanup, and fixes in several drivers

* tag 'hwmon-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (33 commits)
  hwmon: (ina3221) Add of_node_put() before return
  hwmon: (gpio-fan) fix sysfs notifications and udev events for gpio-fan alarms
  hwmon: (gpio-fan) move fan_alarm_init after devm_hwmon_device_register_with_groups
  hwmon: (lm90) Introduce function to update configuration register
  hwmon: (lm90) Cache configuration register value
  hwmon: (lm90) Fix max6658 sporadic wrong temperature reading
  hwmon: (nct7904) Changes comments in probe function.
  hwmon: (nct7904) Add error handling in probe function.
  hwmon: Convert remaining drivers to use SPDX identifier
  hwmon: (max6650) Fix unused variable warning
  hwmon: (pmbus/adm1275) Fix power sampling support
  hwmon: (lm90) simplify getting the adapter of a client
  hwmon: (asus_atk0110) no need to check return value of debugfs_create functions
  hwmon: (max6650) Fix minor formatting issues
  hwmon: (max6650) Improve error handling in max6650_update_device
  hwmon: (max6650) Read non-volatile registers only once
  hwmon: (max6650) Convert to use devm_hwmon_device_register_with_info
  hwmon: (max6650) Simplify alarm handling
  hwmon: (max6650) Cache alarm_en register
  hwmon: (max6650) Declare valid as boolean
  ...
2019-07-11 14:44:13 -07:00
Linus Torvalds 222a21d295 Merge branch 'x86-topology-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 topology updates from Ingo Molnar:
 "Implement multi-die topology support on Intel CPUs and expose the die
  topology to user-space tooling, by Len Brown, Kan Liang and Zhang Rui.

  These changes should have no effect on the kernel's existing
  understanding of topologies, i.e. there should be no behavioral impact
  on cache, NUMA, scheduler, perf and other topologies and overall
  system performance"

* 'x86-topology-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/rapl: Cosmetic rename internal variables in response to multi-die/pkg support
  perf/x86/intel/uncore: Cosmetic renames in response to multi-die/pkg support
  hwmon/coretemp: Cosmetic: Rename internal variables to zones from packages
  thermal/x86_pkg_temp_thermal: Cosmetic: Rename internal variables to zones from packages
  perf/x86/intel/cstate: Support multi-die/package
  perf/x86/intel/rapl: Support multi-die/package
  perf/x86/intel/uncore: Support multi-die/package
  topology: Create core_cpus and die_cpus sysfs attributes
  topology: Create package_cpus sysfs attribute
  hwmon/coretemp: Support multi-die/package
  powercap/intel_rapl: Update RAPL domain name and debug messages
  thermal/x86_pkg_temp_thermal: Support multi-die/package
  powercap/intel_rapl: Support multi-die/package
  powercap/intel_rapl: Simplify rapl_find_package()
  x86/topology: Define topology_logical_die_id()
  x86/topology: Define topology_die_id()
  cpu/topology: Export die_id
  x86/topology: Create topology_max_die_per_package()
  x86/topology: Add CPUID.1F multi-die/package support
2019-07-08 18:28:44 -07:00
Nishka Dasgupta 9f7546570b hwmon: (ina3221) Add of_node_put() before return
Each iteration of for_each_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190706132130.3129-1-nishkadg.linux@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:32 -07:00
Christian Schneider 277c628fa5 hwmon: (gpio-fan) fix sysfs notifications and udev events for gpio-fan alarms
sysfs_notify() and kobject_uevent() are passed the wrong device.
fan_data->hwmon_dev needs to be passed, so that sysfs notification
goes to right place and generated uevent has the right information

Signed-off-by: Christian Schneider <cschneider@radiodata.biz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:32 -07:00
Christian Schneider f2173fa224 hwmon: (gpio-fan) move fan_alarm_init after devm_hwmon_device_register_with_groups
This makes it possible to use the hwmon_dev in fan_alarm_notify(). Otherwise
it would be possible, that a interupt arrives and fan_alarm_notify() is
executed, before hwmon_dev is initialized.

Signed-off-by: Christian Schneider <cschneider@radiodata.biz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:31 -07:00
Guenter Roeck 7a1d220ccb hwmon: (lm90) Introduce function to update configuration register
The code to update the configuration register is repeated several times.
Move it into a separate function. At the same time, un-inline
lm90_select_remote_channel() and leave it up to the compiler to decide
what to do with it. Also remove the 'client' argument from
lm90_select_remote_channel() and from lm90_write_convrate() and take
it from struct lm90_data instead where needed.

This patch reduces code size by more than 800 bytes on x86_64.

Cc: Boyang Yu <byu@arista.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:31 -07:00
Guenter Roeck b849e5d18c hwmon: (lm90) Cache configuration register value
The configuration register does not change on its own. Yet, it is read
in various locations, modified, and written back. Simplify and optimize
the code by caching its value and by only writing it back when needed.

Cc: Boyang Yu <byu@arista.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:30 -07:00
Boyang Yu 62456189f3 hwmon: (lm90) Fix max6658 sporadic wrong temperature reading
max6658 may report unrealistically high temperature during
the driver initialization, for which, its overtemp alarm pin
also gets asserted. For certain devices implementing overtemp
protection based on that pin, it may further trigger a reset to
the device. By reproducing the problem, the wrong reading is
found to be coincident with changing the conversion rate.

To mitigate this issue, set the stop bit before changing the
conversion rate and unset it thereafter. After such change, the
wrong reading is not reproduced. Apply this change only to the
max6657 kind for now, controlled by flag LM90_PAUSE_ON_CONFIG.

Signed-off-by: Boyang Yu <byu@arista.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:30 -07:00
amy.shih a653acf00d hwmon: (nct7904) Changes comments in probe function.
Linux style for comments is the C89 "/* ... */" style,
changes the comments to Linux style.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:29 -07:00
amy.shih b3e2606787 hwmon: (nct7904) Add error handling in probe function.
When register read and write operations return errors, needs to add
error handling.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-07-08 18:11:29 -07:00
Greg Kroah-Hartman b9b667a0c7 FSI changes for 5.3
- Add MAINTAINERS entry. There is now a git tree and a mailing
  list/patchwork for collecting FSI patches
 
  - Bug fix for error driver registration error paths
 
  - Correction for the OCC hwmon driver to meet the spec
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE+nHMAt9PCBDH63wBa3ZZB4FHcJ4FAl0cIIIACgkQa3ZZB4FH
 cJ6z0A//Qy3eu/+s01kq8BAThP77QRyoQP+D7oMoGpr2KxK+82MtFwsuX/vLpcsu
 rYTLn+2xPzY+dWCQx6nWaIij/dkPDWikVarW2+fdMrLhk76XwwkVXPD4J4lUHtVx
 juTWPxLmo7ZAxtwMHyE86hjLR1oTmwZ/arnXYojQ2dka1CZxqpEo7YkRPBLkGjU7
 EcXuCcIGl5ETB9drVsdA8lArLFdgfL/ZFYyEF0epc9KgYrGvJdu1ZdT6bzJkn6C3
 rkCKzQF6fZdszNpo92mjUhkyP3MnnrSVdQPRb/D5wfY9EApfj1YRWS5ikts2lrEf
 tNBat9KJ5nn2AX8FUEKuJazks5ddQk5GOLw6U4vgVayQ0gL8HqofiqybvzKvpX0S
 B0ey0u2d+GeMwiNR+QUNgrnqbbbqy9rLaW8p4zfB70v5qOP8BfWQqnSq+utSqIWZ
 M7xKcial5vQqnBTz0pw+CXVZc0SPD0O7DaK1BmCVOumMAO746eNCPQEwIQVl3Fjt
 FW00qPDWrLnRfdusBWB5mky8b79cnfLht+hLh82gFEeSXpHsRx6rG5luT7moasSK
 EmbXcMM13iVznQk+2IVWWeAXdSDo0yA0eW1SBNBHdrUrdp6jW5pLbDb/F8s+jwQK
 rNYE4IwZYM34L+E/CsFQZw3o5XQy0fsEv6/0tFjjiQPwLeZJZzI=
 =3yOz
 -----END PGP SIGNATURE-----

Merge tag 'fsi-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi into char-misc-next

Joel writes:

FSI changes for 5.3

 - Add MAINTAINERS entry. There is now a git tree and a mailing
 list/patchwork for collecting FSI patches

 - Bug fix for error driver registration error paths

 - Correction for the OCC hwmon driver to meet the spec

* tag 'fsi-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi:
  fsi/core: Fix error paths on CFAM init
  OCC: FSI and hwmon: Add sequence numbering
  MAINTAINERS: Add FSI subsystem
2019-07-03 09:21:25 +02:00
Eddie James afd26118f0 OCC: FSI and hwmon: Add sequence numbering
Sequence numbering of the commands submitted to the OCC is required by
the OCC interface specification. Add sequence numbering and check for
the correct sequence number on the response.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
2019-07-03 10:41:22 +09:30
Guenter Roeck 23297edbc1 hwmon: Convert remaining drivers to use SPDX identifier
This gets rid of the unnecessary license boilerplate, and avoids
having to deal with individual patches one by one.

No functional changes intended.

Reviewed-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:34:11 -07:00
Arnd Bergmann 3253854dc1 hwmon: (max6650) Fix unused variable warning
The newly added variable is only used in an #if block:

drivers/hwmon/max6650.c: In function 'max6650_probe':
drivers/hwmon/max6650.c:766:33: error: unused variable 'cooling_dev' [-Werror=unused-variable]

Change the #if to if() so the compiler can see what is actually
going on.

Fixes: a8463754a5a9 ("hwmon: (max6650) Use devm function to register thermal device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 7d45deb31b hwmon: (pmbus/adm1275) Fix power sampling support
Not every chip supported by this driver supports setting the number
of samples for power averaging. Also, the power monitoring register
is not always a 16-bit register, and the configuration bits used for
voltage sampling are different depending on the register width.
Some conditional code is needed to fix the problem.

On top of all that, the compiler complains about problems with
FIELD_GET and FIELD_PREP macros if the file is built with W=1.
Avoid using those macros to silence the warning.

Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Wolfram Sang e67776cc30 hwmon: (lm90) simplify getting the adapter of a client
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.

Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Greg Kroah-Hartman 08d09d8099 hwmon: (asus_atk0110) no need to check return value of debugfs_create functions
When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Luca Tettamanti <kronos.it@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 228b9e196a hwmon: (max6650) Fix minor formatting issues
CHECK: struct mutex definition without comment
CHECK: Alignment should match open parenthesis

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 0c4a71d365 hwmon: (max6650) Improve error handling in max6650_update_device
Pass errors from i2c_smbus_read_byte_data() back to the caller of
max6650_update_device().

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 62dbe50591 hwmon: (max6650) Read non-volatile registers only once
Only tachometer and alarm status registers are modified by the chip.
All other registers only need to be read only once, and reading them
repeatedly does not add any value.

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck e193acb3d6 hwmon: (max6650) Convert to use devm_hwmon_device_register_with_info
Convert driver to use devm_hwmon_device_register_with_info to simplify
the code and to reduce its size.

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 0d5cc9383e hwmon: (max6650) Simplify alarm handling
Instead of re-reading the alarm register after reporting an alarm,
mark cached values as invalid. While this results in always reading all
data on subsequent reads, it is quite unlikely that such reads will
actually happen before the cache times out. The upside is avoiding
unnecessary unconditional i2c read operations.

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck f5b20b11bb hwmon: (max6650) Cache alarm_en register
The alarm_en register is read each time the is_visible function is called.
Since it is a configuration register, this is completely unnecessary.
Read it once and cache its value.

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck bf8c9edaa5 hwmon: (max6650) Declare valid as boolean
Declare valid as boolean to match its use case.

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck b9d8de4a17 hwmon: (max6650) Improve error handling in max6650_init_client
Do not overwrite errors reported from i2c functions, and don't ignore
any errors.

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck b2905bb8e1 hwmon: (max6650) Introduce pwm_to_dac and dac_to_pwm
Consolidate conversion from pwm value to dac value and from dac value
to pwm value into helper functions.

While doing this, only update the cached dac value if writing it
to the chip was successful after an update. Also, put macro argument
of DIV_FROM_REG() into (), and simplify return statement of
max6650_set_cur_state().

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 8e5e7ddd38 hwmon: (max6650) Use devm function to register thermal device
Use devm_thermal_of_cooling_device_register to register the thermal
cooling device. This lets us drop the remove function.

At the same time, use 'dev' variable in probe function consistently.

Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 792eac1843 hwmon: (core) Add comment describing how hwdev is freed in error path
The hwmon core registers the hwmon device before adding sensors to the
thermal core. If that fails, the hwmon device is released and an error
is returned to the caller. From the code flow, it appears to be necessary
to free struct hwmon_device *, allocated with kzalloc(), in that
situation. This is incorrect, since the data structure will be freed
automatically in hwmon_dev_release() when device_unregister() is called.
This used to result in a double free, which was found and fixed with
commit 74e3512731 ("hwmon: (core) Fix double-free in
__hwmon_device_register()"). This is, however, not obvious; any reader
may erroneously conclude that the data structure is not freed.

Add comment explaining why kfree() is not necessary in this situation.

Reported-by: Eduardo Valentin <eduval@amazon.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Masahiro Yamada 5fe625c136 hwmon: (smsc47m1) fix (suspicious) outside array bounds warnings
Kbuild test robot reports outside array bounds warnings.

This is reproducible for ARCH=sh allmodconfig with the kernel.org
toolchains available at:

https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/8.1.0/x86_64-gcc-8.1.0-nolibc-sh4-linux.tar.xz

  CC [M]  drivers/hwmon/smsc47m1.o
drivers/hwmon/smsc47m1.c: In function 'fan_div_store':
drivers/hwmon/smsc47m1.c:370:49: warning: array subscript [0, 2] is outside array bounds of 'u8[3]' {aka 'unsigned char[3]'} [-Warray-bounds]
  tmp = 192 - (old_div * (192 - data->fan_preload[nr])
                                ~~~~~~~~~~~~~~~~~^~~~
drivers/hwmon/smsc47m1.c:372:19: warning: array subscript [0, 2] is outside array bounds of 'u8[3]' {aka 'unsigned char[3]'} [-Warray-bounds]
  data->fan_preload[nr] = clamp_val(tmp, 0, 191);
  ~~~~~~~~~~~~~~~~~^~~~
drivers/hwmon/smsc47m1.c:373:53: warning: array subscript [0, 2] is outside array bounds of 'const u8[3]' {aka 'const unsigned char[3]'} [-Warray-bounds]
  smsc47m1_write_value(data, SMSC47M1_REG_FAN_PRELOAD[nr],
                             ~~~~~~~~~~~~~~~~~~~~~~~~^~~~

Looking at the code, I believe these are false positives.

While it is ridiculous to patch our driver to make the insane
compiler happy, clarifying the unreachable path will be helpful
not only for compilers but also for humans.

Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[groeck: Use BUG() instead of unreachable() to make objtool happy]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Robert Hancock 9158411b96 hwmon: (pmbus) Add Infineon IRPS5401 driver
Add a driver to support the Infineon IRPS5401 PMIC. This chip has 5
pages corresponding to 4 switching outputs and one linear (LDO) output.
The switching and LDO outputs have slightly different supported
parameters.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
amy.shih b67b735613 hwmon: (nct7904) Fix the incorrect value of tcpu_mask in nct7904_data struct.
Detect the multi-function of voltage, thermal diode and thermistor
from register VT_ADC_MD_REG to set value of tcpu_mask in nct7904_data
struct, set temp[1-5]_input the input values TEMP_CH1~4 and LTD of
temperature. Set temp[6~13]_input the input values of DTS temperature
that correspond to sensors TCPU1~8.

Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Vijay Khemka 344757bac5 hwmon: (pmbus) Add Infineon PXE1610 VR driver
Added pmbus driver for the new device Infineon pxe1610
voltage regulator. It also supports similar family device
PXE1110 and PXM1310.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Alexander Soldatov 8083034251 hwmon: (occ) Add temp sensor value check
The occ driver supports two formats for the temp sensor value.

The OCC firmware for P8 supports only the first format, for which
no range checking or error processing is performed in the driver.
Inspecting the OCC sources for P8 reveals that OCC may send
a special value 0xFFFF to indicate that a sensor read timeout
has occurred, see

https://github.com/open-power/occ/blob/master_p8/src/occ/cmdh/cmdh_fsp_cmds.c#L395

That situation wasn't handled in the driver. This patch adds invalid
temp value check for the sensor data format 1 and handles it the same
way as it is done for the format 2, where EREMOTEIO is reported for
this case.

Signed-off-by: Alexander Soldatov <a.soldatov@yadro.com>
Signed-off-by: Alexander Amelkin <a.amelkin@yadro.com>
Reviewed-by: Alexander Amelkin <a.amelkin@yadro.com>
Cc: Edward A. James <eajames@us.ibm.com>
Cc: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Adamski, Krzysztof (Nokia - PL/Wroclaw) c83529c17e hwmon: (pmbus/adm1275) support PMBUS_VIRT_*_SAMPLES
The device supports setting the number of samples for averaging the
measurements. There are two separate settings - PWR_AVG for averaging
PIN and VI_AVG for averaging VIN/VAUX/IOUT, both being part of
PMON_CONFIG register. The values are stored as exponent of base 2 of the
actual number of samples that will be taken.

Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
[groeck: Dropped unused variables]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:33:01 -07:00
Guenter Roeck 5696e4aaab hwmon: (pwm-fan) Check return value from devm_add_action_or_reset
devm_add_action_or_reset() can fail due to a memory allocation failure.
Check for it and return the error if that happens.

Fixes: 37bcec5d9f ("hwmon: (pwm-fan) Use devm_thermal_of_cooling_device_register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:32:34 -07:00
Guenter Roeck b9bb92e1d1 hwmon: (gpio-fan) Check return value from devm_add_action_or_reset
devm_add_action_or_reset() can fail due to a memory allocation failure.
Check for it and return the error if that happens.

Fixes: 9534784550 ("hwmon: (gpio-fan) Use devm_thermal_of_cooling_device_register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-23 18:32:34 -07:00
Thomas Gleixner d2912cb15b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:55 +02:00
Olof Johansson df767c0a43 ARM SCMI updates/fixes for v5.3
1. Correction to ARM document ID referred in SCMI protocol binding
 2. Fix to correct bitfield definitions for SENSOR_DESC attributes which
    otherwise will calculate sensor values on wrong scale
 3. Adds the missing rate_discrete flag setting so that discrete clocks
    are handled correctly. Without this fix it assumes continuous range
    which is incorrect
 4. Adds support to read and scale the sensor values based on the factor
    read from the firmware
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAl0A9jcACgkQAEG6vDF+
 4pgW1Q/+LprgPlA2krfWlfBY85cku+N+intI8RCO1jVMDgQlFUVi82pTKlTEnp+F
 9/qp2MMKbJWlJoT8Yte24WQtgqWTJkkZ6zA0kczh3lruqrcSeCfcA0s0uvHiWFup
 tsOR7FlyLnALb86Pa9qXI921MDF2H/594rJUpKkQFoB418YlIAW1uCIfOPmqQgcc
 i7grh6nOwYJ4pprg5zgltXqHGtv3vqBR1kCWl6Av48eB7mdmz7zMxmM1Hfka0HGn
 ZFfjQE73gowJ+CZU8uSYn9JAY+nraUug/NX55J5w9kyAABKVtZmuJW+4+sQKmJ9S
 05ODDcuBbsJmEDGEXggEr1XzRcpCxf6T5g2hwd6Am2ckBWvW5HdD/VBOjXXCogTh
 t12ZLwfmsfUZTiz7s1St+YbHAZ47VtHcs6+t4vnkz27rJg988CYTNo/mes6iU05E
 ynCg84crSYBA9316Q6bWgAriFnSRbRujXJH+S44PEU/1eNH+Ddutv6OvICY+jYuc
 Ku1wkkyoeKVnYV2Mx7HVu3ij4AycLwspyBxEQLsW2SBVA50VI8aaUGEXnrdjCzYW
 fadFzQjhzwTmGzzrvGUl0xrvxXdLVw0awRebO58pRh508xLwK11xnZthR9aRqgR7
 mcE431L1xSDwFN0WaxJ197no5OGaAT8tZUIXS5WwNKfGsWjMD+w=
 =RZCT
 -----END PGP SIGNATURE-----

Merge tag 'scmi-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers

ARM SCMI updates/fixes for v5.3

1. Correction to ARM document ID referred in SCMI protocol binding
2. Fix to correct bitfield definitions for SENSOR_DESC attributes which
   otherwise will calculate sensor values on wrong scale
3. Adds the missing rate_discrete flag setting so that discrete clocks
   are handled correctly. Without this fix it assumes continuous range
   which is incorrect
4. Adds support to read and scale the sensor values based on the factor
   read from the firmware

* tag 'scmi-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  hwmon: scmi: Scale values to target desired HWMON units
  firmware: arm_scmi: fetch and store sensor scale
  firmware: arm_scmi: update rate_discrete in clock_describe_rates_get
  firmware: arm_scmi: fix bitfield definitions for SENSOR_DESC attributes
  dt-bindings: arm: fix the document ID for SCMI protocol documentation

Signed-off-by: Olof Johansson <olof@lixom.net>
2019-06-17 04:54:11 -07:00
Florian Fainelli ac778e6263 hwmon: scmi: Scale values to target desired HWMON units
If the SCMI firmware implementation is reporting values in a scale that
is different from the HWMON units, we need to scale up or down the value
according to how far apart they are.

Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[sudeep.holla: added check of scale = 0 for early exit in scmi_hwmon_scale]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2019-06-12 12:29:51 +01:00
Linus Torvalds 9331b6740f SPDX update for 5.2-rc4
Another round of SPDX header file fixes for 5.2-rc4
 
 These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
 added, based on the text in the files.  We are slowly chipping away at
 the 700+ different ways people tried to write the license text.  All of
 these were reviewed on the spdx mailing list by a number of different
 people.
 
 We now have over 60% of the kernel files covered with SPDX tags:
 	$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
 	Files checked:            64533
 	Files with SPDX:          40392
 	Files with errors:            0
 
 I think the majority of the "easy" fixups are now done, it's now the
 start of the longer-tail of crazy variants to wade through.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
 sxVEiFZo8ZU9v1IoRb1I
 =qU++
 -----END PGP SIGNATURE-----

Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull yet more SPDX updates from Greg KH:
 "Another round of SPDX header file fixes for 5.2-rc4

  These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
  added, based on the text in the files. We are slowly chipping away at
  the 700+ different ways people tried to write the license text. All of
  these were reviewed on the spdx mailing list by a number of different
  people.

  We now have over 60% of the kernel files covered with SPDX tags:
	$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
	Files checked:            64533
	Files with SPDX:          40392
	Files with errors:            0

  I think the majority of the "easy" fixups are now done, it's now the
  start of the longer-tail of crazy variants to wade through"

* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
  ...
2019-06-08 12:52:42 -07:00
Robert Hancock 4a60570dce hwmon: (pmbus/core) Treat parameters as paged if on multiple pages
Some chips have attributes which exist on more than one page but the
attribute is not presently marked as paged. This causes the attributes
to be generated with the same label, which makes it impossible for
userspace to tell them apart.

Marking all such attributes as paged would result in the page suffix
being added regardless of whether they were present on more than one
page or not, which might break existing setups. Therefore, we add a
second check which treats the attribute as paged, even if not marked as
such, if it is present on multiple pages.

Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-05 18:36:27 -07:00
Adamski, Krzysztof (Nokia - PL/Wroclaw) 38463721ec hwmon: (pmbus/core) mutex_lock write in pmbus_set_samples
update_lock is a mutex intended to protect write operations. It was not
taken, however, when _pmbus_write_word_data is called from
pmbus_set_samples() function which may cause problems especially when
some PMBUS_VIRT_* operation is implemented as a read-modify-write cycle.

This patch makes sure the lock is held during the operation.

Fixes: 49c4455dcc ("hwmon: (pmbus) Introduce PMBUS_VIRT_*_SAMPLES registers")
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
[groeck: Declared and initialized missing 'data' variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-05 18:36:27 -07:00
Eduardo Valentin c41dd48e21 hwmon: (core) add thermal sensors only if dev->of_node is present
Drivers may register to hwmon and request for also registering
with the thermal subsystem (HWMON_C_REGISTER_TZ). However,
some of these driver, e.g. marvell phy, may be probed from
Device Tree or being dynamically allocated, and in the later
case, it will not have a dev->of_node entry.

Registering with hwmon without the dev->of_node may result in
different outcomes depending on the device tree, which may
be a bit misleading. If the device tree blob has no 'thermal-zones'
node, the *hwmon_device_register*() family functions are going
to gracefully succeed, because of-thermal,
*thermal_zone_of_sensor_register() return -ENODEV in this case,
and the hwmon error path handles this error code as success to
cover for the case where CONFIG_THERMAL_OF is not set.
However, if the device tree blob has the 'thermal-zones'
entry, the *hwmon_device_register*() will always fail on callers
with no dev->of_node, propagating -EINVAL.

If dev->of_node is not present, calling of-thermal does not
make sense. For this reason, this patch checks first if the
device has a of_node before going over the process of registering
with the thermal subsystem of-thermal interface. And in this case,
when a caller of *hwmon_device_register*() with HWMON_C_REGISTER_TZ
and no dev->of_node will still register with hwmon, but not with
the thermal subsystem. If all the hwmon part bits are in place,
the registration will succeed.

Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-06-05 18:36:27 -07:00
Thomas Gleixner b886d83c5b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 315 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:17 +02:00
Thomas Gleixner 55716d2643 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 428
Based on 1 normalized pattern(s):

  this file is released under the gplv2

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 68 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:16 +02:00
Thomas Gleixner 0ebc04719c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 408
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license v2 as published
  by the free software foundation this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 1 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.493982682@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:14 +02:00
Thomas Gleixner a10e763b87 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 372
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 135 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:10 +02:00
Thomas Gleixner 4505153954 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 333
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not write to the free
  software foundation inc 59 temple place suite 330 boston ma 02111
  1307 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 136 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:06 +02:00
Thomas Gleixner 1d0ea0692a treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 332
Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  publishhed by the free software foundation

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 48 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.292339952@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:06 +02:00
Thomas Gleixner 36edc93958 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 330
Based on 1 normalized pattern(s):

  this file is subject to the terms and conditions of version 2 of the
  gnu general public license see the file copying in the main
  directory of this archive for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 55 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.108941081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:06 +02:00
Thomas Gleixner 0677607741 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 313
Based on 1 normalized pattern(s):

  this software program is licensed subject to the gnu general public
  license gpl version 2 june 1991 available at http www gnu org
  licenses old licenses gpl 2 0 html

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 1 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.615718144@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:04 +02:00
Thomas Gleixner ff7924b024 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 272
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 this program is distributed
  in the hope that it will be useful but without any warranty without
  even the implied warranty of merchantability or fitness for a
  particular purpose see the gnu general public license for more
  details you should have received a copy of the gnu general public
  license along with this program if not write to the free software
  foundation inc 51 franklin street fifth floor boston ma 02110 1301
  usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 3 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141334.517214694@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:30:30 +02:00
Thomas Gleixner 21eb0be9ac treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 271
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license v2 as published
  by the free software foundation this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details you
  should have received a copy of the gnu general public license along
  with this program if not write to the free software foundation inc
  51 franklin street fifth floor boston ma 02110 1301 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141334.424952652@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:30:30 +02:00
Thomas Gleixner 3e5580c465 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 253
Based on 1 normalized pattern(s):

  license gplv2

and 1 additional normalized pattern(s):

  this program is free software you can redistribute it and or modify it
  under the terms and conditions of the gnu general public license version
  2 as published by the free software foundation this program is
  distributed in the hope it will be useful but without any warranty
  without even the implied warranty of merchantability or fitness for a
  particular purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 5 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141332.723143934@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:30:27 +02:00
Thomas Gleixner 0376148f30 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 197
Based on 1 normalized pattern(s):

  license terms gnu general public license v2

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 37 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.724130665@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:29:22 -07:00
Thomas Gleixner 1802d0beec treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 655 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:41 -07:00
Thomas Gleixner 873e65bc09 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 167
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not write to the free
  software foundation inc 59 temple place suite 330 boston ma 02111
  1307 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 83 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:39 -07:00
Thomas Gleixner 935912c538 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 164
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not write to the free
  software foundation inc 51 franklin street fifth floor boston ma
  02110 1301 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 12 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.745497013@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:38 -07:00
Thomas Gleixner c942fddf87 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157
Based on 3 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [kishon] [vijay] [abraham]
  [i] [kishon]@[ti] [com] this program is distributed in the hope that
  it will be useful but without any warranty without even the implied
  warranty of merchantability or fitness for a particular purpose see
  the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [graeme] [gregory]
  [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
  [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
  [hk] [hemahk]@[ti] [com] this program is distributed in the hope
  that it will be useful but without any warranty without even the
  implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1105 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:37 -07:00
Thomas Gleixner 1a59d1b8e0 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 156
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details you
  should have received a copy of the gnu general public license along
  with this program if not write to the free software foundation inc
  59 temple place suite 330 boston ma 02111 1307 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1334 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:35 -07:00
Thomas Gleixner 2874c5fd28 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:32 -07:00
Thomas Gleixner a912e80bd0 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 151
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version you should have received a copy of the
  gnu general public license along with this program if not write to
  the free software foundation inc 675 mass ave cambridge ma 02139 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 35 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:28 -07:00
Thomas Gleixner 80503b23b2 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 149
Based on 1 normalized pattern(s):

  licensed under the gpl 2 or later

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 82 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:25:18 -07:00
Thomas Gleixner 3e0a4e8580 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 or at your option any
  later version this program is distributed in the hope that it will
  be useful but without any warranty without even the implied warranty
  of merchantability or fitness for a particular purpose see the gnu
  general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 44 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.032047323@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-24 17:39:02 +02:00