[Why]
passive update planes still spends a litte more
time on some cases.
[How]
Remove unnecessary trace which involving in some register read.
Disable debug output for release build.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP LL CTS1.4 4.3.2.1 test failure.
[how]
The failure is caused by not handling DP link loss
hpd short pusle during set mode. The change is to read link status
before set mode link training. If link is lost, re-verify link caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently, when the VSP infopacket is rebuilt in DM, it is not updated
when being programmed in encoder.
[HOW]
Add new VSP case for update_info_frame
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.
[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Skipping initial link training will result in no verified link cap for
mode enumeration. Some versions of the BIOS seem to have PHY programming
sequence issue as well if initial link training is skipped, resulting in
a softlock in BIOS command table.
[How]
Identify the empty dongle hotplug case, and still do initial link
training.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In 99% user case, edp will be post by vbios.
In 1% / current case: Lenovo don't light up edp panel in vbios
post stage, vbios won't be lit up. Thus in dal when we init DCN
10 hw, we power up edp, then we start detect_sink, but internal
time is too short, when we detect it, HPD is still low, so we don't
detect the edp, and edp shows black.
[How]
When we init hw, we wait edp HPD to high after power up edp.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An earlier change added update of interdependent dlg/ttu params for pipes
not being updated in the current call. The code fails to check if the other
pipes are actually active yet causing an assert.
This change adds a check for surface presence on the pipes before updating
the interdepenednt params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.
YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> .....
[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC warns when a REG_WAIT takes a while and full-on errors
with stack dump on REG_WAIT timeout. Most of the time it isn't
a real issue.
[How]
Make DC cool its jets - taking a while is a debug message (because
it is not something that normal users should need to be aware of),
and timeouts are warnings (because it technically shouldn't
happen, but it's not a big deal if it does)
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a dual channel format and should be treated like other
video formats
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain configurations, such as PX configs or some Vega20 parts
DC gets created without connectors.
[How]
Drop the dm_error print when no connectors.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When XGMI is enabled, the DP reference clock needs to be adjusted
according to the XGMI spread spectrum percentage and mode. But first,
we need the ability to fetch this info.
[How]
Within the BIOS parser, Read from vBIOS when XGMI SS info is requested.
In addition, diags build uses include_legacy/atomfirmware.h for the
smu_info_v3_3 table headers. Update that as well.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll need a way to differentiate Vega 20 in DC
[How]
Add a DCE_VERSION_12_1 enum, which will be returned as the DC version if
the ASIC used is a Vega 20.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the flip-rate is below the minimum supported variable refresh rate
range for the monitor the front porch wait will timeout and be
frequently misaligned resulting in stuttering and/or flickering.
The FreeSync module can still maintain a smooth and flicker free
image when the monitor has a refresh rate range such that the maximum
refresh > 2 * minimum refresh by utilizing low framerate compensation,
"below the range".
[How]
Hook up the pre-flip and post-flip handlers from the FreeSync module.
These adjust the minimum/maximum vrr range to duplicate frames
when appropriate by tracking flip timestamps.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value observed on some
systems
[How]
There was earlier patch for dspclk:
'drm/amd/display: Raise dispclk value for dce_update_clocks'
Adding +15% workaround also to to dce112_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The behavior of drm_atomic_helper_cleanup_planes differs depending on
whether the commit was asynchronous or not. When it's called from
amdgpu_dm_atomic_commit_tail during a typical atomic commit the
plane state has been swapped so it calls cleanup_fb on the old plane
state.
However, in the asynchronous commit codepath the call to
drm_atomic_helper_commit also calls dm_plane_helper_cleanup_fb after
atomic_async_update has been called. Since the plane state is updated
in place and has not been swapped the cleanup_fb call affects the new
plane state.
This results in a use after free for the given sequence:
- Fast update, fb1 pin/ref, fb1 unpin/unref
- Fast update, fb2 pin/ref, fb2 unpin/unref
- Slow update, fb1 pin/ref, fb2 unpin/unref
- Fast update, fb2 pin/ref -> use after free. bug
[How]
Disallow framebuffer changes in the fast path. Since this includes
a NULL framebuffer, this means that only framebuffers that have
been previously pin+ref at least once will be used, preventing a
use after free.
This has a significant throughput reduction for cursor updates where
the framebuffer changes. For most desktop usage this isn't a problem,
but it does introduce performance regressions for two specific IGT
tests:
- cursor-vs-flip-toggle
- cursor-vs-flip-varying-size
Fixes: 2cc751931afc ("drm/amd/display: Add fast path for cursor plane updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It should not return 0 for error case as '0' is actually
a special value for index.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On errors, dma_buf_get returns a negative error code, rather than NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If register value is updating, reset timeout counter.
It improves robustness of SOC15_WAIT_ON_RREG.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove bit 31 for scratch2 to indicate the Hardware bug work around is active.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Scan enc/jpeg fences to init dpg pause new state in begin use.
It will help set dpg mode to desire state actively.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Always check all vcn ring status during dpg mode stop, it will help
identify which vcn ring may cause the issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is a bug fix.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under Dynamic Power Gate mode, UVD_STATUS needn't be checked.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use page directory based shared buffer implementation
now available as common code for Xen frontend drivers.
Remove flushing of shared buffer on page flip as this
workaround needs a proper fix.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Add a fallback detection method for TypeC legacy ports in case the
VBT port information used to detect normally such ports is
incorrect.
For the fallback method we use the TypeC legacy mode specific HPD
interrupt flag which should only be raised for a legacy port.
WARN if the VBT port info is incorrect.
In a case where we'd detect the port in a contradicting way both as a
legacy and also as a USB DP and/or TBT alternate port treat the port
as legacy (by also emitting a WARN from icl_update_tc_port_type).
v2:
- Repurpose the detection as a fallback method instead of using
it only for the DP legacy case. By now we should normally use VBT to
detect DP legacy ports as well.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-5-imre.deak@intel.com
Atm HPD disconnect events on TypeC ports will break things, since we'll
switch the TypeC mode (between legacy and disconnected modes as well as
among USB DP alternate, Thunderbolt alternate and disconnected modes) on
the fly from the HPD disconnect interrupt work while the port may be
still active.
Even if the port happens to be not active during the disconnect we'd
still have a problem during a subsequent modeset or AUX transfer that
could happen regardless of the port's connected state. For instance the
system resume display mode restore code and userspace could perform a
modeset on the port or userspace could start an AUX transfer even if the
port is in disconnected state.
To fix this keep TypeC legacy ports in legacy mode whenever we're not
suspended. This mode is a static configuration as opposed to the
Thunderbolt and USB DP alternate modes between which we can switch
dynamically.
We determine if a TypeC port is legacy (wired to a legacy HDMI or a
legacy DP connector) via the VBT DDI port specific USB-TypeC and
Thunderbolt flags. If both these flags are cleared then the port is
configured for legacy mode.
On such legacy ports we'll run the TypeC PHY connect sequence explicitly
during driver loading and system resume (vs. running the sequence during
HPD processing). The connect will succeed even if the display is not
connected to begin with (or disappears during the suspended state) since
for legacy ports the PORT_TX_DFLEXDPPMS / DP_PHY_MODE_STATUS_COMPLETED
flag is always set (as opposed to the USB DP alternate mode where it
gets set only when a display is connected).
Correspondingly run the TypeC PHY disconnect sequence during system
suspend and driver unloading. For the unloading case I had to split
up intel_dp_encoder_destroy() to be able to have the 1. flush any
pending encoder work, 2. disconnect TC PHY, 3. call DRM core cleanup and
kfree on the encoder object.
For now run the PHY disconnect during suspend only for TypeC legacy
ports. We will need to disconnect even in USB DP alternate mode in the
future, but atm we don't have a way to reconnect the port in this mode
during resume if the display disappears while being suspended. So for
now punt on this case.
Note that we do not disconnect the port during runtime suspend; in
legacy mode there are no shared HW resources (PHY lanes) with other HW
blocks (USB), so no need to release / reacquire these resources as with
USB DP alternate mode. The only reason to disconnect legacy ports during
system suspend is that the PORT_TX_DFLEXDPPMS /
DP_PHY_MODE_STATUS_COMPLETED flag must be rechecked and the port must be
connected again during system resume. We'll also have to turn the check
for this flag into a poll, after figuring out what's the proper timeout
value for it.
v2:
- Remove the redundant special casing of legacy mode when doing a
disconnect in icl_tc_port_connected(). It's guaranteed already that we
won't disconnect legacy ports in that function.
- Add a note about the new intel_ddi_encoder_destroy() hook.
- Reword the commit message after switching to the VBT based detection.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108070
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108924
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-4-imre.deak@intel.com
This is needed by the next patch to determine if a DDI TypeC port is
physically wired to a legacy DP or legacy HDMI connector or if the port
is wired to a USB-C/Thunderbolt connector.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-3-imre.deak@intel.com
It's useful to see at which point a TypeC port gets disconnected, so add
a debug print for it.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-2-imre.deak@intel.com
Having completed a test run of gem_eio across all machines in CI we also
observe the phenomenon (of lost interrupts after resetting the GPU) on
gen3 machines as well as the previously sighted gen6/gen7. Let's apply
the same HWSTAM workaround that was effective for gen6+ for all, as
although we haven't seen the same failure on gen4/5 it seems prudent to
keep the code the same.
As a consequence we can remove the extra setting of HWSTAM and apply the
register from a single site.
v2: Delazy and move the HWSTAM into its own function
v3: Mask off all HWSP writes on driver unload and engine cleanup.
v4: And what about the physical hwsp?
v5: No, engine->init_hw() is not called from driver_init_hw(), don't be
daft. Really scrub HWSTAM as early as we can in driver_init_mmio()
v6: Rename set_hwsp as it was setting the mask not the hwsp register.
v7: Ville pointed out that although vcs(bsd) was introduced for g4x/ilk,
per-engine HWSTAM was not introduced until gen6!
References: https://bugs.freedesktop.org/show_bug.cgi?id=108735
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181218102712.11058-1-chris@chris-wilson.co.uk
In August 2018 the BSPEC changed the ICL port programming sequence to
closely resemble earlier gen programming sequence. Restrict combo phy to
HBR max rate unless eDP panel is connected to port.
v2: remove debug code that Imre found
v3: simplify translation table if-else
v4: edp translation table now based on link rate and low_swing
v5: Misc review comments + r-b
BSpec: 21257
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1545084827-5776-1-git-send-email-clinton.a.taylor@intel.com
Lucas writes:
"nothing major this time, mostly some cleanups that were found on the
way of reworking the code in preparation for new feature additions."
Small conflict in drivers/gpu/drm/etnaviv/etnaviv_drv.c because
drm-misc-next also has a patch to switch over to _put() functions.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1545130845.5874.23.camel@pengutronix.de
It only written and we don't infer any useful information from
it anymore. Remove it.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The etnaviv_gpu header only needs to know about the pointer types, so
replace by a forward declaration and only include the headers where needed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The only event function that is called from IRQ context is event_free,
which is already using atomic bitmap operations, so we can avoid taking
the event spinlock in this function completely. As other the other
functions still using the event spinlock are all called from normal
process context, we can avoid disabling IRQs while holding the spinlock.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
When the pipe_config's update_pipe flag is set we may need to update the
panel fitting settings. On GEN9+ this means we need to update the crtc's
scaler settings.
This fixes the following WARN_ON, during i915 loading on an Asrock
B150M Pro4S/D3 board with an i5-6500 CPU / graphics:
[drm:pipe_config_err [i915]] *ERROR* mismatch in pch_pfit.enabled
(expected no, found yes)
pipe state doesn't match!
WARNING: CPU: 3 PID: 305 at drivers/gpu/drm/i915/intel_display.c:12084
With line 12084 being the I915_STATE_WARN call inside the
"if (!intel_pipe_config_compare())" block in verify_crtc_state().
On this board with 2 1920x1080 monitors connected over HDMI the GOP
initializes both monitors at 1920x1080 and despite no scaling being
necessary configures a scaler for one of them.
When booting with fastboot=1 on the initial modeset needs_modeset will
be false while update_pipe is true. Since we were not calling
skl_update_scaler_crtc() in this case we would leave the scaler enabled
causing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181217141903.4182-1-hdegoede@redhat.com
We have an update for HuC for BXT.
Load the latest version.
v2: Change the subject.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207182840.9292-2-anusha.srivatsa@intel.com
DSC can be supported per DP connector. This patch adds a per connector
debugfs node to expose DSC support capability by the kernel.
The same node can be used from userspace to force DSC enable.
force_dsc_en written through this debugfs node is used to force
DSC even for lower resolutions.
Credits to Ville Syrjala for suggesting the proper locks to be used
and to Lyude Paul for explaining how to use them in this context
v8:
* Add else if (ret) for drm_modeset_lock (Lyude)
v7:
* Get crtc, crtc_state from connector atomic state
and add proper locks and backoff (Ville, Chris Wilson, Lyude)
(Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>)
* Use %zu for printing size_t variable (Lyude)
v6:
* Read fec_capable only for non edp (Manasi)
v5:
* Name it dsc sink support and also add
fec support in the same node (Ville)
v4:
* Add missed connector_status check (Manasi)
* Create i915_dsc_support node only for Gen >=10 (manasi)
* Access intel_dp->dsc_dpcd only if its not NULL (Manasi)
v3:
* Combine Force_dsc_en with this patch (Ville)
v2:
* Use kstrtobool_from_user to avoid explicit error checking (Lyude)
* Rebase on drm-tip (Manasi)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206005407.4698-1-manasi.d.navare@intel.com
It indicates a pin/unpin imbalance bug somewhere. While the bug isn't
necessarily in the call chain hitting this, it's at least one part
involved.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Page queue is supported on Vega20 with SDMA firmware
123 onwards.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Vega20 uses ring id 1 for page queues EOP irq while previous
ASICs take ring id 3.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need new invalidation engine layout due to new SDMA page
queues added.
V2: fix coding style and add correct return value
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As two more SDMA page queue rings are added on Vega20.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the fence is already signaled it is perfectly normal to get a NULL
fence here. But since we can't export that we need to use a stub fence.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently driver only psp v11 support vmr.
v2: squash in unused variable removal (Alex)
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If PSP FW is running already, driver will not load PSP FW again and skip
it. So psp fw version is not correct if reading it from FW binary file,
need to get right version from register.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no need to access register such as mmSMC_IND_INDEX_11
and mmSMC_IND_DATA_11, PCIE_INDEX, PCIE_DATA through KIQ because
they are VF-copy.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
XGMI hive put kfd_pre_reset into amdgpu_device_lock_adev,
but outside req_full_gpu of sriov.
It would make sriov hang during reset.
Signed-off-by: Wentao Lou <Wentao.Lou@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The fimd hardware supports different blend modes. Add pixel blend mode
property and make it configurable, by modifying the blend equation.
Tested on TRATS2 with Exynos 4412 CPU, on top of linux-next-20181019.
Signed-off-by: Christoph Manszewski <c.manszewski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The fimd hardware supports variable plane alpha. Currently planes
are opaque, make this configurable.
Tested on TRATS2 with Exynos 4412 CPU, on top of linux-next-20181019.
Signed-off-by: Christoph Manszewski <c.manszewski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Avoid expensive indirect calls in the fast path DMA mapping
operations by directly calling the dma_direct_* ops if we are using
the directly mapped DMA operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
With the new validation code, a malicious user-space app could
potentially submit command streams with enough buffer-object and resource
references in them to have the resulting allocated validion nodes and
relocations make the kernel run out of GFP_KERNEL memory.
Protect from this by having the validation code reserve TTM graphics
memory when allocating.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
---
v2: Removed leftover debug printouts
SFC (Scaler & Format Converter) units are shared between VD and VEBoxes.
They also happen to have separate reset bits. So, whenever we want to reset
one or more of the media engines, we have to make sure the SFCs do not
change owner in the process and, if this owner happens to be one of the
engines being reset, we need to reset the SFC as well.
This happens in 4 steps:
1) Tell the engine that a software reset is going to happen. The engine
will then try to force lock the SFC (if currently locked, it will
remain so; if currently unlocked, it will ignore this and all new lock
requests).
2) Poll the ack bit to make sure the hardware has received the forced
lock from the driver. Once this bit is set, it indicates SFC status
(lock or unlock) will not change anymore (until we tell the engine it
is safe to unlock again).
3) Check the usage bit to see if the SFC has ended up being locked to
the engine we want to reset. If this is the case, we have to reset
the SFC as well.
4) Unlock all the SFCs once the reset sequence is completed.
Obviously, if we are resetting the whole GPU, we don't have to worry
about all of this.
BSpec: 10989
BSpec: 10990
BSpec: 10954
BSpec: 10955
BSpec: 10956
BSpec: 19212
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-4-chris@chris-wilson.co.uk
In Gen11, only even numbered "logical" VDBoxes are hooked up to an SFC
(Scaler & Format Converter) unit. We will use this information to decide
when the SFC units need to be reset.
BSpec: 20189
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-3-chris@chris-wilson.co.uk
We currently require that our per-engine reset can be called from any
context, even hardirq, and in the future wish to perform the device
reset without holding struct_mutex (which requires some lockless
shenanigans that demand the lowlevel intel_reset_gpu() be able to be
used in atomic context). Test that we meet the current requirements by
calling i915_reset_engine() from under various atomic contexts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-2-chris@chris-wilson.co.uk
After declaring a terminally wedged device, we allow ourselves to
recover on the next GPU reset (manually triggered), or resume. Check
that resetting a wedged device does work.
v2: Add rpm (taken explicitly in the subtest in case we remove the outer
wakeref) and early warning to i915_reset() for missed wakerefs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-1-chris@chris-wilson.co.uk
Define IS_GEN() similarly to our IS_GEN_RANGE(). but use gen instead of
gen_mask to do the comparison. Now callers can pass then gen as a parameter,
so we don't require one macro for each gen.
The following spatch was used to convert the users of these macros:
@@
expression e;
@@
(
- IS_GEN2(e)
+ IS_GEN(e, 2)
|
- IS_GEN3(e)
+ IS_GEN(e, 3)
|
- IS_GEN4(e)
+ IS_GEN(e, 4)
|
- IS_GEN5(e)
+ IS_GEN(e, 5)
|
- IS_GEN6(e)
+ IS_GEN(e, 6)
|
- IS_GEN7(e)
+ IS_GEN(e, 7)
|
- IS_GEN8(e)
+ IS_GEN(e, 8)
|
- IS_GEN9(e)
+ IS_GEN(e, 9)
|
- IS_GEN10(e)
+ IS_GEN(e, 10)
|
- IS_GEN11(e)
+ IS_GEN(e, 11)
)
v2: use IS_GEN rather than GT_GEN and compare to info.gen rather than
using the bitmask
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-2-lucas.demarchi@intel.com
RANGE makes it longer, but clearer. We are also going to add a macro to
check an individual gen, so add the _RANGE prefix here.
Diff generated with:
sed 's/IS_GEN(/IS_GEN_RANGE(/g' drivers/gpu/drm/i915/{*/,}*.{c,h} -i
v2: use IS_GEN rather than GT_GEN
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-1-lucas.demarchi@intel.com
This time around, seeing some love for some older hw:
- a2xx gpu support for apq8060 (hp touchpad) and imx5 (headless
gpu-only mode)
- a2xx gpummu support (a2xx was pre-iommu)
- mdp4 display support for apq8060/touchpad
For display/dpu:
- a big pile of continuing dpu fixes and cleanups
On the gpu side of things:
- per-submit statistics and traceevents for better profiling
- a6xx crashdump support
- decouple get_iova() and page pinning.. so we can unpin from
physical memory inactive bo's while using softpin to lower
cpu overhead
- new interface to set debug names on GEM BOs and debugfs
output improvements
- additional submit flag to indicate buffers that are used
to dump (so $debugfs/rd cmdstream dumping is useful with
softpin + state-objects)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvVvLPD9_Z4kyfGe98Y--byj6HbxHivEYSgF7Rq7=bFnw@mail.gmail.com
Mostly just initial support for Turing TU104/TU106 chipsets. Support
for TU102 is missing as I don't yet have HW, but it should be trivial
to add in later in the merge window (in theory).
It's a bit of a rough first pass that'll get improved in future
releases as a finish figuring out some of the other HW changes, but
it's good enough as it stands for modesetting and suspend/resume etc.
Acceleration bring-up is incomplete due to NVIDIA not yet having
provided FW images for me to use, though command submission and copy
engines are functional already.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv7KmfcQqZcx+wh_1UKjTovp4PH_5UVMfeyxUu-M9WLZfw@mail.gmail.com
These changes contain a couple of minor fixes for host1x and the Falcon
library in Tegra DRM. There are also a couple of missing pieces that
finally enable support for host1x, VIC and display on Tegra194. I've
also added a patch that enables audio over HDMI using the SOR which has
been tested, and works, on both Tegra186 and Tegra194.
-----BEGIN PGP SIGNATURE-----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=WHND
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.21-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.21-rc1
These changes contain a couple of minor fixes for host1x and the Falcon
library in Tegra DRM. There are also a couple of missing pieces that
finally enable support for host1x, VIC and display on Tegra194. I've
also added a patch that enables audio over HDMI using the SOR which has
been tested, and works, on both Tegra186 and Tegra194.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134712.32683-1-thierry.reding@gmail.com
[airlied: make etnaviv build again]
amdgpu:
- DC trace support
- More DC documentation
- XGMI hive reset support
- Rework IH interaction with KFD
- Misc fixes and cleanups
- Powerplay updates for newer polaris variants
- Add cursor plane update fast path
- Enable gpu reset by default on CI parts
- Fix config with KFD/HSA not enabled
amdkfd:
- Limit vram overcommit
- dmabuf support
- Support for doorbell BOs
ttm:
- Support for simultaneous submissions to multiple engines
scheduler:
- Add helpers for hw with preemption support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207233119.16861-1-alexander.deucher@amd.com
[Why]
Legacy cursor plane updates from drm helpers go through the full
atomic codepath. A high volume of cursor updates through this slow
code path can cause subsequent page-flips to skip vblank intervals
since each individual update is slow.
This problem is particularly noticeable for the compton compositor.
[How]
A fast path for cursor plane updates is added by using DRM asynchronous
commit support provided by async_check and async_update. These don't do
a full state/flip_done dependency stall and they don't block other
commit work.
However, DC still expects itself to be single-threaded for anything
that can issue register writes. Screen corruption or hangs can occur
if write sequences overlap. Every call that potentially perform
register writes needs to be guarded for asynchronous updates to work.
The dc_lock mutex was added for this.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106175
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During DDB allocation, we try to distribute enough blocks for each plane
to hit the highest watermark level; if that fails, we retry each lower
level (which should require fewer blocks) until we find one that's
possible (or until the whole commit is rejected as impossible). We need
to reset our running block count when trying each lower level, otherwise
all lower levels will fail as well.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d8e8749802 ("drm/i915: Switch to level-based DDB allocation algorithm (v5)")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212191720.3706-1-matthew.d.roper@intel.com
Since this is not needed any more on the latest SMC firmware.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I retested Bonaire (gfx7 dGPU) and it works fine.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The return statement is redundant as there is a return statement
immediately before it so we have dead code that can be removed.
Also remove the unused declaration of ret.
Detected by CoverityScan, CID#1473793 ("Structurally dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Adding an extra MI_STORE_DWORD_IMM to the gpu relocation path for gen3
was good, but still not good enough. To survive 24+ hours under test we
needed to perform not one, not two but three extra store-dw. Doing so
for each GPU relocation was a little unsightly and since we need to
worry about userspace hitting the same issues, we should apply the dummy
store-dw into the EMIT_FLUSH.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
References: 7fa28e1469 ("drm/i915: Write GPU relocs harder with gen3")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134037.11848-1-chris@chris-wilson.co.uk
(cherry picked from commit a889580c08)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Currently we allocate a scratch page for each engine, but since we only
ever write into it for post-sync operations, it is not exposed to
userspace nor do we care for coherency. As we then do not care about its
contents, we can use one page for all, reducing our allocations and
avoid complications by not assuming per-engine isolation.
For later use, it simplifies engine initialisation (by removing the
allocation that required struct_mutex!) and means that we can always rely
on there being a scratch page.
v2: Check that we allocated a large enough scratch for I830 w/a
Fixes: 06e562e7f515 ("drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5") # v4.18.20
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108850
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.18.20+
(cherry picked from commit 5179749925)
[Joonas: Use new function in gen9_init_indirectctx_bb too]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Braswell is really picky about having our writes posted to memory before
we execute or else the GPU may see stale values. A wmb() is insufficient
as it only ensures the writes are visible to other cores, we need a full
mb() to ensure the writes are in memory and visible to the GPU.
The most frequent failure in flushing before execution is that we see
stale PTE values and execute the wrong pages.
References: 987abd5c62 ("drm/i915/execlists: Force write serialisation into context image vs execution")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206084431.9805-3-chris@chris-wilson.co.uk
(cherry picked from commit 490b8c65b9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Noticed this while working on redoing the reference counting scheme in
the DP MST helpers. Nouveau doesn't attempt to call
drm_dp_mst_topology_mgr_destroy() at all, which leaves it leaking all of
the resources for drm_dp_mst_topology_mgr and it's children mstbs+ports.
Fixes: f479c0ba4a ("drm/nouveau/kms/nv50: initial support for DP 1.2 multi-stream")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should hopefully fix a regression some people have been seeing since EVO
push buffers were moved to VRAM by default on Pascal GPUs.
Fixes: d00ddd9da ("drm/nouveau/kms/nv50-: allocate push buffers in vidmem on pascal")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 4.19+
It's not just GEN9 platforms that allow for pipes to be disabled via
the DFSM register, but all later platforms as well.
v2: drop pointless parentheses (Ville)
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211192545.140081-1-bob.j.paauwe@intel.com
The DDB allocation algorithm currently used by the driver grants each
plane a very small minimum allocation of DDB blocks and then divies up
all of the remaining blocks based on the percentage of the total data
rate that the plane makes up. It turns out that this proportional
allocation approach is overly-generous with the larger planes and can
leave very small planes wthout a big enough allocation to even hit their
level 0 watermark requirements (especially on APL, which has a smaller
DDB in general than other gen9 platforms). Or there can be situations
where the smallest planes hit a lower watermark level than they should
have been able to hit with a more equitable division of DDB blocks, thus
limiting the overall system sleep state that can be achieved.
The bspec now describes an alternate algorithm that can be used to
overcome these types of issues. With the new algorithm, we calculate
all plane watermark values for all wm levels first, then go back and
partition a pipe's DDB space second. The DDB allocation will calculate
what the highest watermark level that can be achieved on *all* active
planes, and then grant the blocks necessary to hit that level to each
plane. Any remaining blocks are then divided up proportionally
according to data rate, similar to the old algorithm.
There was a previous attempt to implement this algorithm a couple years
ago in bb9d85f6e9 ("drm/i915/skl: New ddb allocation algorithm"), but
some regressions were reported, the patch was reverted, and nobody
ever got around to figuring out exactly where the bug was in that
version. Our watermark code has evolved significantly in the meantime,
but we're still getting bug reports caused by the unfair proportional
algorithm, so let's give this another shot.
v2:
- Make sure cursor allocation stays constant and fixed at the end of
the pipe allocation.
- Fix some watermark level iterators that weren't handling the max
level.
v3:
- Ensure we don't leave any DDB blocks unused by using DIV_ROUND_UP+min
to calculate the extra blocks for each plane. (Ville)
- Replace a while() loop with a for() loop to be more consistent with
surrounding code. (Ville)
- Clean unattainable watermark levels with memset rather than directly
clearing the member fields. Also do the same for the transition
watermark values if they can't be achieved. (Ville)
- Drop min_disp_buf_needed calculations in skl_compute_plane_wm() since
the results are no longer needed or used. (Ville)
- Drop skl_latency[0] != 0 sanity check; both watermark methods already
account for an invalid 0 latency by returning FP_16_16_MAX. (Ville)
v4:
- Break DDB allocation loop when total_data_rate=0 rather than
alloc_size=0. If total_data_rate has dropped to 0, all remaining
planes are disabled, which isn't true for alloc_size (we might just
have not had any remaining blocks to hand out). Plus
total_data_rate=0 is the case we need to avoid to a prevent a
div-by-0. (Ville)
- s/DIV_ROUND_UP/DIV64_U64_ROUND_UP/ to prevent 32-bit breakage (Ville)
v5:
- Don't forget to move 'start' pointer forward for UV surface when
setting plane DDB boundaries. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105458
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-2-matthew.d.roper@intel.com
The bspec gives an if/else chain for choosing whether to use "method 1"
or "method 2" for calculating the watermark "Selected Result Blocks"
value for a plane. One of the branches of the if chain is:
"Else If ('plane buffer allocation' is known and (plane buffer
allocation / plane blocks per line) >=1)"
Since our driver currently calculates DDB allocations first and the
actual watermark values second, the plane buffer allocation is known at
this point in our code and we include this test in our driver's logic.
However we plan to soon move to a "watermarks first, ddb allocation
second" sequence where we won't know the DDB allocation at this point.
Let's drop this arm of the if/else statement (effectively considering
the DDB allocation unknown) as an independent patch so that any
regressions can be more accurately bisected to either the different
watermark value (in this patch) or the new DDB allocation (in the next
patch).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-1-matthew.d.roper@intel.com
[Why]
These properties aren't being carried over when the atomic state.
This tricks atomic check and commit tail into performing underscan
and scaling operations when they aren't needed.
With the patch that forced scaling/RMX_ASPECT on by default this
results in many unnecessary surface updates and hangs under certain
conditions.
[How]
Duplicate the properties.
Fixes: 91b66c47ba ("drm/amd/display: Set RMX_ASPECT as default")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the "max bpc" isn't explicitly set in the atomic state then it
have a value of 0. This has the correct behavior of limiting a panel
to 8bpc in the case where the panel supports 8bpc. In the case of eDP
panels this isn't a true assumption - there are panels that can only
do 6bpc.
Banding occurs for these displays.
[How]
Initialize the max_bpc when the connector resets to 8bpc. Also carry
over the value when the state is duplicated.
Bugzilla: https://bugs.freedesktop.org/108825
Fixes: 307638884f72 ("drm/amd/display: Support amdgpu "max bpc" connector property")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 91b66c47ba.
Forcing RMX_ASPECT as default uses the preferred/native mode's timings
for any mode the user selects and scales the image. This provides a
a consistently nicer result in the case where the selected mode's
refresh rate matches the native mode's refresh but this isn't always
the case.
For example, if the monitor is 1080p@144Hz and the preferred mode is
60Hz then even if the user selects 1080p@144Hz as their selected mode
they'll get 1080p@60Hz.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This function was renamed in a previous commit. Update the stub
function name for builds with CONFIG_HSA_AMD disabled.
Fixes: 611736d844 ("drm/amdgpu: Add KFD VRAM limit checking")
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case of msm drm bind failure, pm runtime put sync
is called from dsi driver which issues an asynchronous
put on mdss device. Subsequently when dpu_mdss_destroy
is triggered the change will make sure to put the mdss
device in suspend and clearing pending work if not
scheduled.
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Do some cleanup in the static inline functions defined in
dpu_media_info.h by cleaning up gotos and unneeded local
variables.
v3: Added spaces between operators per Seal Paul and Sam Ravnborg
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove more static inline functions that are lightly used and/or
very simple and easy to build into the calling functions.
v3: Fix a nit from Sean Paul
v2: Removed another unused function from dpu_hw_lm.c and add back
dpu_crtc_get_client_type() since there was a question regarding
its usefulness.
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Do some debugfs cleanups from across the DPU driver. The DRM
destroy functions will do a recursive delete on the entire
debugfs node so there is no need to store dentry pointers for
the debugfs files that are persistent for the life of the
driver. This also means that the destroy functions can go
away too.
Also, use standard API functions where applicable instead of
using hand written code.
v3: No changes
v2: Add more code; most of the dpu debugfs files should be
addressed now.
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
dpu_irq.c does some unneeded checks and passes control
to dpu_core_irq.c The simple functions can be defined
in the same file where we use them and the files and
their associated hangers on can be deleted.
Additionally the postinstall hook isn't used even
in dpu_core_irq.c so zap that entire path.
v3: No changes
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Allow the KMS operation 'irq_postinstall' to be optional
so that the target display drivers don't need to define
a dummy function if they don't need one.
v3: No changes
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Outside of superfluous parameter checks the dpu_hw_blk_init()
doesn't have any failure paths. Switch it over to be a void
function and we can remove error handling paths in all the functions
that call it. While we're in those functions remove unneeded
initialization for a static variable.
v3: No changes
v2: Removed a cleanup intended for a different patch
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove some unused container_of() helper functions.
v3: No changes
v2: Retained still used helper functions in the name of readability
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The static inline function dpu_crtc_enabled() is only called once
and the function that calls it in turn is only called once and
the return value can be easily checked in the calling functions
so collapse everything down.
v3: No changes
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
dpu_crtc_get_mixer_height() is only used once and the value it
returns can be easily derived from the calling function.
v3: No changes
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The functions in dpu_dbg.c aren't used. The two main dump functions
fail after a lookup from dpu_dbg_base.reg_base_list which turns out
to never be populated and once those are removed the rest of the
file doesn't make any sense.
v3: No changes
v2: Moved some unrelated changes to another patch
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Each time it's called we're holding the crtc modeset lock, so it's
redundant.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It's just for debugfs output, we don't need it
Changes in v2:
- None
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of assigning/clearing the crtc on vblank enable/disable, we can
just assign and clear the crtc on modeset. That allows us to just toggle
the encoder's vblank interrupts on vblank_enable.
So why is this important? Previously the driver was using the legacy
pointers to assign/clear the crtc. Legacy pointers are cleared _after_
disabling the hardware, so the legacy pointer was valid during
vblank_disable, but that's not something we should rely on.
Instead of relying on the core ordering the legacy pointer assignments
just so, we'll assign the crtc in dpu_crtc enable/disable. This is the
only place that mapping can change, so we're covered there.
We're also taking advantage of drm_crtc_vblank_on/off. By using this, we
ensure that vblank_enable/disable can never be called while the crtc is
off (which means the assigned crtc will always be valid). As such, we
don't need to use modeset locks or the crtc_lock in the
vblank_enable/disable routine to be sure state is consistent.
...I think.
Changes in v2:
- Changed crtc check in toggle_vblank to != (Jeykumar)
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[dpu_crtc.c change needed to be manually applied b/c of the dpu_crtc_reset change]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The drm_crtc_vblank_on/off calls in enable/disable guarantee that we
won't call this function when crtc is not enabled.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Matches dpu_crtc_enable and we'll need the old state in a future patch
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The indirection of registering a callback and opaque pointer isn't reall
useful when there's only one callsite. So instead of having the
vblank_cb registration, just give encoder a crtc and let it directly
call the vblank handler.
In a later patch, we'll make use of this further.
Changes in v2:
- None
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
I think the intention here was to protect the enc->crtc access, but
that's insufficient to avoid enc->crtc changing. Fortunately we're
already holding the modeset lock when this is called (from
atomic_check), so remove the crtc_lock and add a modeset lock check.
While we're at it, use the encoder mask from crtc state instead of
legacy pointer.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are 4 times that _dpu_crtc_vblank_enable_no_lock() is called:
1- crtc enable
2- crtc disable
3- crtc vblank enable
4- crtc vblank disable
When we enable or disable the crtc, we call drm_crtc_vblank_on and
drm_crtc_vblank_off respectively. That will gate vblank enables and
disables to only being called when the crtc is active. That means that
we can just enable/disable pm runtime in crtc enable/disable. This will
be beneficial in trying to eliminate blocking calls from the vblank call
chain.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add modeset lock checks to functions that could be called outside the
core atomic stack.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It's for legacy drivers, for atomic drivers crtc->state->encoder_mask
should be used to map encoder to crtc.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[seanpaul resolved conflict with async param of dpu_encoder_kickoff]
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch wraps dpu_core_perf_crtc_release_bw() with modeset locks
since it digs into the state objects.
Changes in v2:
- None
Changes in v3:
- Use those nifty new DRM_MODESET_LOCK_ALL_* helpers (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that runtime resume is handled in encoder, we don't need to worry
about crtc_lock recursion when calling pm_runtime_(get|put). So drop the
lock drops in _dpu_crtc_vblank_enable_no_lock().
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The crtc runtime resume doesn't actually operate on the crtc, but rather
its encoders. The problem with this is that we need to inspect the crtc
state to get the currently connected encoders. Since runtime resume
isn't guaranteed to be called while holding the modeset locks (although
it sometimes is), this presents a race condition.
Now that we have ->enabled on the virtual encoders, and a lock to
protect it, just call resume on each encoder and only restore the ones
that are enabled.
Changes in v2:
- None
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a bool to dpu_encoder_virt to track whether the encoder is enabled
or not. Repurpose the enc_lock mutex to ensure that it is consistent
with the hw state.
Changes in v2:
- None
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
enc_spinlock instead of enc_spin_lock.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we don't have any event handlers, remove dpu_power_handle!
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It's only used in core_perf, so stick it there (and change the name to
reflect that).
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It's needed for struct dss_module_power, and is currently being pulled
in by dpu_power_handle.h
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It's unused
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of registering through dpu_power_handle just to get a call on
runtime_resume, call the crtc function directly.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
power_events are only used for pm_runtime, and that's all handled in
dpu_kms. So just call vbif_init_memtypes at the correct times.
Changes in v2:
- Removed obsolete comment (Jeykumar)
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There's only one client -- core, and it's only used for runtime pm which
is already refcounted.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It's only used for debugfs, so just output the enum value instead.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since dpu_crtc subclasses crtc_state, we need a custom .reset hook in
order to allocate the right amount of memory to accommodate the
additional struct members in dpu_crtc_state. So bring it [partially]
back.
Relevant KASAN splat:
[ 10.333382] ==================================================================
[ 10.344288] BUG: KASAN: slab-out-of-bounds in kmemdup+0x50/0x80
[ 10.350390] Read of size 736 at addr ffffffc0d9f06080 by task frecon/394
[ 10.358861] CPU: 6 PID: 394 Comm: frecon Tainted: G W 4.19.4 #121
[ 10.366476] Hardware name: Google Cheza (rev2) (DT)
[ 10.371514] Call trace:
[ 10.374087] dump_backtrace+0x0/0x194
[ 10.377878] show_stack+0x20/0x28
[ 10.381330] dump_stack+0xa0/0xc8
[ 10.384783] print_address_description+0x78/0x2e0
[ 10.389639] kasan_report+0x290/0x2d0
[ 10.393428] check_memory_region+0x20/0x14c
[ 10.397740] __asan_loadN+0x14/0x1c
[ 10.401345] kmemdup+0x50/0x80
[ 10.404524] dpu_crtc_duplicate_state+0x58/0xa0
[ 10.409228] drm_atomic_get_crtc_state+0xac/0x178
[ 10.414095] __drm_atomic_helper_set_config+0x54/0x4a4
[ 10.419393] drm_atomic_helper_set_config+0x60/0xb4
[ 10.424435] drm_mode_setcrtc+0x720/0x760
[ 10.428570] drm_ioctl_kernel+0xd8/0x13c
[ 10.432617] drm_ioctl+0x380/0x4f4
[ 10.436150] drm_compat_ioctl+0x54/0x13c
[ 10.440219] __arm64_compat_sys_ioctl+0x1d8/0xef4
[ 10.445086] el0_svc_common+0xd8/0x138
[ 10.448961] el0_svc_compat_handler+0x58/0x68
[ 10.453463] el0_svc_compat+0x8/0x18
[ 10.458712] Allocated by task 56:
[ 10.462148] kasan_kmalloc.part.4+0x48/0xf4
[ 10.466465] kasan_kmalloc+0x8c/0xa0
[ 10.470165] kmem_cache_alloc_trace+0x25c/0x27c
[ 10.474848] drm_atomic_helper_crtc_reset+0x68/0x98
[ 10.479877] drm_mode_config_reset+0xc4/0x19c
[ 10.484383] msm_drm_bind+0x814/0x8dc
[ 10.488169] try_to_bring_up_master.part.7+0x48/0xac
[ 10.493282] component_master_add_with_match+0x158/0x198
[ 10.498758] msm_pdev_probe+0x328/0x348
[ 10.502736] platform_drv_probe+0x74/0xc8
[ 10.506877] really_probe+0x1ac/0x35c
[ 10.510659] driver_probe_device+0xd4/0x118
[ 10.514975] __device_attach_driver+0xc8/0xf4
[ 10.519477] bus_for_each_drv+0xb4/0xe4
[ 10.523439] __device_attach+0xd0/0x158
[ 10.527394] device_initial_probe+0x24/0x30
[ 10.531715] bus_probe_device+0x50/0xe4
[ 10.535681] deferred_probe_work_func+0xac/0xdc
[ 10.540376] process_one_work+0x3f0/0x6d4
[ 10.544521] worker_thread+0x3f4/0x520
[ 10.548399] kthread+0x1b4/0x1c8
[ 10.551740] ret_from_fork+0x10/0x18
[ 10.556986] Freed by task 0:
[ 10.559967] (stack is not available)
[ 10.565216] The buggy address belongs to the object at ffffffc0d9f06080
which belongs to the cache kmalloc-1024 of size 1024
[ 10.578268] The buggy address is located 0 bytes inside of
1024-byte region [ffffffc0d9f06080, ffffffc0d9f06480)
[ 10.590248] The buggy address belongs to the page:
[ 10.595195] page:ffffffbf0367c000 count:1 mapcount:0 mapping:ffffffc0de40f680 index:0x0 compound_mapcount: 0
[ 10.605321] flags: 0x4000000000008100(slab|head)
[ 10.610100] raw: 4000000000008100 ffffffbf0369fa08 ffffffbf0367f008 ffffffc0de40f680
[ 10.618077] raw: 0000000000000000 0000000000150015 00000001ffffffff 0000000000000000
[ 10.626049] page dumped because: kasan: bad access detected
[ 10.633341] Memory state around the buggy address:
[ 10.638282] ffffffc0d9f06180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 10.645710] ffffffc0d9f06200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 10.653139] >ffffffc0d9f06280: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
[ 10.660571] ^
[ 10.665774] ffffffc0d9f06300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 10.673210] ffffffc0d9f06380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 10.680639] ==================================================================
Fixes: a6ba45afda41 (drm/msm/dpu: Replace dpu_crtc_reset by atomic helper)
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Bruce Wang <bzwang@chromium.org>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bruce Wang <bzwang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch allows using drm/msm without qcom display hardware. It adds a
amd,imageon compatible, which is used instead of qcom,adreno, but does
not require a top level msm node.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This allows controlling which of the 8 lanes are used for 6 bit color.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A2XX has its own very simple MMU.
Added a msm_use_mmu() function because we can't rely on iommu_present to
decide to use MMU or not.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When trying to get the display up on my sdm845 board I noticed that
the display wouldn't probe if I had the dsi1 node marked as "disabled"
even though my board doesn't use dsi1. It looks like the msm code
adds all nodes to its list of components even if they are disabled. I
believe this doesn't work because all registered components need to
come up before we finish probing. Let's do like other DRM code and
only add available components.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a buffer object name for the a6xx crashdumper so it can be
seen with the changes introduced by 7799a98edd
("drm/msm: Add a name field for gem objects").
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
dadb36b7ec42 ("drm/msm: Add a common function to free kernel buffer objects")
missed freeing the crashdumper state for a6xx.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch sprinkles a few async/legacy_cursor_update checks
through commit to ensure that cursor updates aren't blocked on vsync.
There are 2 main components to this, the first is that we don't want to
wait_for_commit_done in msm_atomic before returning from atomic_complete.
The second is that in dpu we don't want to wait for frame_done events when
updating the cursor.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There exists a case where a flush of a plane/dma may have been triggered
& started from an async commit. If that plane/dma is subsequently disabled
by the next commit, the flush register will continue to hold the flush
bit for the disabled plane. Since the bit remains active,
pending_kickoff_cnt will never decrement and we'll miss frame_done
events.
This patch limits the check of flush_register to include only those bits
which have been updated with the latest commit.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of msm drm bind failure, dpu_mdss_destroy is triggered.
In this function, resources are freed and pm runtime disable is
called, which triggers dpu_mdss_disable. Now in dpu_mdss_disable,
driver tries to access a memory which is already freed. This
results in kernel panic. Fix this by ensuring proper sequence
of dpu destroy and disable calls.
Changes in v2:
- Removed double spacings [Jeykumar]
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fix the dsi clock names in the DSI 10nm PLL driver to
match the names in the dispcc driver as those are
according to the clock plan of the chipset.
Changes in v2:
- Update the clock diagram with the new clock name
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
otherwise, priv->kms is non-NULL and msm_drm_uninit will cause a panic.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the mdp5_cfg_hw entry for MDP5 version v1.15 found on msm8917.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@gmail.com>
derived from the a3xx driver and tested on the following hardware:
imx51-zii-rdu1 (a200 with 128kb gmem)
imx53-qsrb (a200)
msm8060-tenderloin (a220)
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Makes it possible to have MMU for GPU but not display.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For allocation in contiguous memory when the GPU has MMU but not mdp4.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@gmail.com>
To lower CPU overhead, future userspace will be switching to pinning
iova and avoiding the use of relocs, and only include cmds table entries
for IB1 level cmdstream (but not IB2 or state-groups).
This leaves the kernel unsure what to dump for rd/hangrd cmdstream
dumping. So add a MSM_SUBMIT_BO_DUMP flag so userspace can indicate
buffers that contain cmdstream (or are otherwise important to dump).
Signed-off-by: Rob Clark <robdclark@gmail.com>
When the userspace tries to read the crashstate dump, the read side
implementation in the driver currently ascii85 encodes all the binary
buffers and it does this each time the read system call is called.
A userspace tool like cat typically does a page by page read and the
number of read calls depends on the size of the data captured by the
driver. This is certainly not desirable and does not scale well with
large captures.
This patch encodes the buffer only once in the read path. With this there
is an immediate >10X speed improvement in crashstate save time.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For reasons that I'm sure made perfect sense at the time we were
opting to defer the iova alloc / pin on the ringbuffer until HW
init time so when we moved to iova reference counting we ended
up adding a reference count every time the hardware started.
Not that it mattered (because the ring is always around) but
it did make the debug output look odd. Allocate and pin the iova
at create time instead.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For debugging purposes it is useful to assign descriptions
to buffers so that we know what they are used for. Add
a field to the buffer object and use that to name the various
kernel side allocations which ends up looking like like this
in /d/dri/X/gem:
flags id ref offset kaddr size madv name
00040000: I 0 ( 1) 00000000 0000000070b79eca 00004096 memptrs
vmas: [gpu: 01000000,mapped,inuse=1]
00020000: I 0 ( 1) 00000000 0000000031ed4074 00032768 ring0
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a reference count to track how many times a particular
chunk of iova memory is pinned (mapped) in the iomu and
add msm_gem_unpin_iova to give up references.
It is important to note that msm_gem_unpin_iova replaces
msm_gem_put_iova because the new implicit behavior
that an assigned iova in a given vma is now valid for the
life of the buffer and what we are really focusing on is
the use of that iova.
For now the unmappings are lazy; once the reference counts
go to zero they *COULD* be unmapped dynamically but that
will require an outside force such as a shrinker or
mm_notifiers. For now, we're just focusing on getting
the counting right and setting ourselves up to be ready
for the future.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Yongqiang Sun