Switch the device tree to the new compatibles introduced in the clock drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 SoC is built around a pair of Cortex-A7 cores,
which have the usual generic timers. Report this in the DT.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All Allwinner A20 boards we support can only use either EMAC or GMAC,
as they share the same pins. As we have switched all supported to
GMAC, we should alias GMAC (the active controller) as ethernet0,
so u-boot will insert the MAC address for the correct controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CubieTruck uses the GMAC with an RGMII phy.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has EMAC and GMAC muxed on the same pins.
Add pin sets with gmac function for MII and RGMII mode to the DTSI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The module clocks in the A31 are still compatible with the A10 one. Add the SPI
module clocks and the PLL6 in the device tree to allow their use by the SPI
controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART2 is used on CubieTruck to connect to the Bluetooth module.
Add the pin set used in this case.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch will add a basic board support DT for the
LinkSprite pcDuino board.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>
On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>
The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: Helge Deller <deller@gmx.de>
This commit:
f8dae00684d678afa13041ef170cecfd1297ed40: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.
This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases coverage
of the multiplatform defconfig and some DTS changes that plumbs up some
of the devices that now have bindings and driver support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ymAC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
With commit d8d14bd09c ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.
However I missed that there was still a stale declaration in
arch/tile/.. which now causes a compile error on tile:
In file included from fs/dcookies.c:28:0:
include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'
Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged. The correct declaration is now in include/linux/compat.h
The build error was reported by Fenguang's build bot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.
The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>
Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels. Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.
Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in 72197ca7a1 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=UVOK
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC DT Fixes for v3.14
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in 72197ca7a1 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
* tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
Signed-off-by: Olof Johansson <olof@lixom.net>
Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:
warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))
Instead enable TI EDMA support from defconfig.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=mxq4
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.13 (incremental #2)
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
* tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed
ARM: kirkwood: kirkwood_pm_init() should return void
ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Signed-off-by: Olof Johansson <olof@lixom.net>
Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
SMP is a user configurable option, not a hardware feature and should not
be selected.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled
by tegra_defconfig. However, this config option no longer exists, so
no longer selects DEBUG_FS, and nothing else selects it either. So,
"make tegra_defconfig" no longer enables DEBUG_FS in .config.
Rebuild tegra_defconfig on top of next-20140424, while manually
re-enabling DEBUG_FS.
Reasons for removed entries are:
- I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT
- DRM_PANEL: selected by DRM_TEGRA
- NEW_LEDS: selected by many things; at least VT
- LEDS_CLASS: selected by many things; at least VT
- LEDS_TRIGGERS: selected by many things; at least VT
- COMMON_CLK_DEBUG: no longer exists
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
multi_v7_defconfig was missing a large number of options that were in
tegra_defconfig. This patch adds them. The changes fall into the
following categories:
* Enable more Tegra SoC options/drivers.
* Enable more drivers for Tegra boards.
* Enable more options that are useful for running distros.
The patch removes a few lines as well, simply because those options are
now selected by something else, and "make savedefconfig" removes them. I
verified that the options appear in .config after
"make multi_v7_defconfig".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This board was missed when converting all the others to proper
abstracted GPIO handling. Fix it up the right way by requesting
and driving GPIO line 0 high through gpiolib to power off the
machine.
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 78d1632183 deleted the
static mappings of the core modules, but this static map is
still needed on the Integrator/CP (not the Integrator/AP).
Restore the static map on the Integrator/CP.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This allows us to probe the clock controller devices and boot to a
serial console on all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The same workaround as ff999b8a09
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more
Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Introduction of PTE_WRITE to distinguish between writable but clean
and truly read-only pages
- FIQs enabling/disabling clean-up (they aren't used on arm64)
- CPU resume fix for the per-cpu offset restoring
- Code comment typos
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=tWas
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pyll ARM64 patches from Catalin Marinas:
- Build fix with DMA_CMA enabled
- Introduction of PTE_WRITE to distinguish between writable but clean
and truly read-only pages
- FIQs enabling/disabling clean-up (they aren't used on arm64)
- CPU resume fix for the per-cpu offset restoring
- Code comment typos
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Introduce PTE_WRITE
arm64: mm: Remove PTE_BIT_FUNC macro
arm64: FIQs are unused
arm64: mm: fix the function name in comment of cpu_do_switch_mm
arm64: fix build error if DMA_CMA is enabled
arm64: kernel: fix per-cpu offset restore on resume
arm64: mm: fix the function name in comment of __flush_dcache_area
arm64: mm: use ubfm for dcache_line_size
Maxime Ripard