As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Neil Zhang <zhangwm@marvell.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With "select USB_ISP1301 ...", it could happen that I2C isn't selected although
USB_ISP1301 depends on it. Fixing with "depends on ..." and emulating the
condition via "|| !()".
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the ARM architecture mach-pnx4008. No direct support or user
feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc
maintainers.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Add support for a generic non-pci UHCI companion controller.
Existing board files for arch-vt8500 updated to include UHCI
support.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and drivers.
There's some scsi changes that I think also went in through the scsi tree, but
they merge just fine. All of these patches have been in the linux-next tree
for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAQhpcACgkQMUfUDdst+yms4wCgpMbfFYTZ8lHpDnXHYFv6qw8j
FIsAmwT4mbT7m8C0k+ELV/5T2e0eYJEQ
=QetG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and
drivers. There's some scsi changes that I think also went in through
the scsi tree, but they merge just fine. All of these patches have
been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflicts in include/scsi/scsi_device.h (same libata
conflict that Jeff had already encountered)
* tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams
usb: Add quirk detection based on interface information
usb: s3c-hsotg: Add header file protection macros in s3c-hsotg.h
USB: ehci-s5p: Add vbus setup function to the s5p ehci glue layer
USB: add USB_VENDOR_AND_INTERFACE_INFO() macro
USB: notify phy when root hub port connect change
USB: remove 8 bytes of padding from usb_host_interface on 64 bit builds
USB: option: add ZTE MF821D
USB: sierra: QMI mode MC7710 moved to qcserial
USB: qcserial: adding Sierra Wireless devices
USB: qcserial: support generic Qualcomm serial ports
USB: qcserial: make probe more flexible
USB: qcserial: centralize probe exit path
USB: qcserial: consolidate usb_set_interface calls
USB: ehci-s5p: Add support for device tree
USB: ohci-exynos: Add support for device tree
USB: ehci-omap: fix compile failure(v1)
usb: host: tegra: pass correct pointer in ehci_setup()
USB: ehci-fsl: Update ifdef check to work on 64-bit ppc
USB: serial: keyspan: Removed unrequired parentheses.
...
Correct "Enbale" -> "Enable", in the desc for USB_HCD_BCMA
and USB_HCD_SSB.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the FS USB code is not being actively used for omap2+
there's no point keeping it around for omap2+.
Let's make the FS USB platform init code omap1 only so
we can remove the last user of omap_read/write for omap2+,
and simplify things for further USB, DMA, and device tree
related work.
While at it, also group the mach includes for the related
drivers.
Cc: linux-usb@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
The CI13xxx usb host needs the root TT support to work properly.
Allow selecting this for the CI13xxx too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three Kconfig entries with "--- help ---" attributes, and over
2000 Kconfig entries with "---help---" attributes. Apparently the three
attributes with embedded spaces are valid. Still, I see little reason
for using this obscure variant. And replacing those three attributes
with the common variant makes grepping Kconfig files for help texts a
bit easier too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ohci-nxp duplicates the isp1301 driver. This patch removes this code and makes
ohci-nxp use the new separate isp1301 driver instead.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add EHCI driver for MIPS SEAD-3 development platform.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now replaced by the new ssb USB driver, which also supports
devices with an EHCI controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom ssb bus. The ssb bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the ssb bus at the same time.
The old ssb OHCI USB driver will be removed in the next step as this
driver also provide an OHCI driver and an EHCI for the cores supporting
it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom bcma bus. The bcma bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the bcma bus at the same time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ath79 usb driver doesn't do anything special and is now converted
to the generic ehci and ohci driver.
This was tested on a TP-Link TL-WR1043ND (AR9132)
Acked-by: Gabor Juhos <juhosg@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
CC: linux-mips@linux-mips.org
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a generic driver for platform devices. It works like the PCI
driver and is based on it. This is for devices which do not have an own
bus but their EHCI controller works like a PCI controller. It will be
used for the Broadcom bcma and ssb USB EHCI controller.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a generic driver for platform devices. It works like the PCI
driver and is based on it. This is for devices which do not have an own
bus but their OHCI controller works like a PCI controller. It will be
used for the Broadcom bcma and ssb USB OHCI controller.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This ehci driver is mainly designed to support host controller found on
Marvell PXA and MMP Soc series.
Add the dependence to avoid the potential build failure which may
include two EHCI controller drivers.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ehci-mv.c can cover Marvell PXA and MMP series including PXA168,
so this driver seems redundant now.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Cc: <tanmay.upadhyay@einfochips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish Kconfig text by providing the Freescale family name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
This patch adds USB OHCI driver for Samsung EXYNOS SoCs.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for EHCI compliant HSUSB Host controller found
on Marvell Socs.
It fits both OTG and SPH controller on marvell Socs, including
PXA9xx/MMP2/MMP3/MGx.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is mod_host prototype support for renesas_usbhs driver.
It doesn't support USB-Hub, and USB-DMAC for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
to make it look like OHCI and EHCI, we introduce
that symbol and USB_XHCI_HCD depend on that
instead of PCI.
[bigeasy@linutronix.de: wire up USB_ARCH_HAS_HCD]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the MACH_MX* macros are scheduled for removal, so just depend
on ARCH_MXC instead. The Kconfig text makes it clear on which
SoC the driver runs on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for big endian GRUSBHC UHCI controllers.
The HCD bus glue will probe the register interface to determine
the endianness of the controller.
Tested on GR-LEON4-ITX board which has a controller with little endian
interface and on custom LEON3 board with a BE controller.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for universal host controllers that use
big endian descriptors. Support for BE descriptors requires a non-PCI
host controller. For kernels with PCI-only UHCI there should be no
change in behaviour.
This patch tries to replicate the technique used to support BE descriptors
in the EHCI HCD. Parts added to uhci-hcd.h are basically copy'n'paste from
ehci.h.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for big endian mmio to the UHCI HCD. Big endian
mmio is supported by adding a flag bit to the UHCI HCD replicating the
solution used in the EHCI HCD.
When adding big endian support this patch also adds a check to see if we
need to support HCs with PCI I/O registers when we support HCs with MMIO.
This patch also adds 'const' to the register access functions' uhci_hcd
argument.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the UHCI part of the GRLIB GRUSBHC controller
found on some LEON/GRLIB SoCs.
The UHCI HCD previously only supported controllers connected over PCI.
This patch adds support for the first non-PCI UHCI HC. I have tried to
replicate the solution used in ehci-hcd.c.
Tested on GR-LEON4-ITX board (LEON4/GRLIB with GRUSBHC) and x86 with Intel
UHCI HC.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.
This patch also extends the uhci_{read,write}* functions to allow accesses
to registers not mapped into PCI I/O space. This extension also includes
the addition of a void __iomem pointer to the uhci structure.
A new Kconfig option is added to signal that the system has a non-PCI HC.
If this Kconfig option is set, uhci-hcd.c will include generic reset functions
for systems that do not make use of keyboard and mouse legacy support. PCI
controllers will still always use the reset functions from pci-quirks
This patch is followed by a patch that adds bus glue for the first non-PCI
UHCI HC.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the GRLIB GRUSBHC EHCI controller from
Aeroflex Gaisler. The controller is typically found on LEON/GRLIB
SoCs.
Tested on GR-LEON4-ITX with with little endian interface and on
LEON3 system on GR-PCI-XC5V development board for big endian
controller.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Atheros AR71XX/AR7240 SoCs have a built-in OHCI controller.
This patch adds the necessary glue code to make the generic OHCI
driver usable for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Atheros AR71XX/AR91XX SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds host USB high speed driver for samsung S5P series. This
is initial driver and we need additional implementation to support some
functions like power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some bluetooth dongles want ISO mode, and the limited support that the
sl811 offers today is sufficient. So add a Kconfig option for people
to optionally get access to the partial functionality.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is used across all MSM SoCs. Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add bus glue for USB controller commonly found in PMC-Sierra MSP71xx family of SoC's.
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Enable runtime PM and mark no_callbacks flag. OTG device, parent of
HCD takes care of putting hardware into low power mode. Adjust port
power wakeup flags during system suspend and resume.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips. The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce the CONFIG_USB_EHCI_HCD_OMAP option to select
EHCI support on OMAP3 and later chips. This scales better
than having a long line of dependencies for each new OMAP
with EHCI support.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
The CNS3XXX SOC has include USB EHCI and OHCI compatible controllers.
This patch adds the necessary glue logic to allow ehci-hcd and ohci-hcd
drivers to work on CNS3XXX
The EHCI and OHCI controllers share a common clock control and reset
bit, therefore additional check for the timming of enabling and disabling
is required. The USB bit of PLL Power Down Control is also shared by OTG,
24MHzUART clock, Crypto clock, PCIe reference clock, and Clock Scale
Generator. Therefore we only ensure it is enabled, while not disabling it.
Signed-off-by: Mac Lin <mkl0301@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Commit 126512e3f2 added support for FSL's USB
controller on powerpc. In this commit the Open Firmware code was selected
and compiled unconditionally.
This breaks on ARM systems from FSL which use the same driver (.i.e. the i.MX
series), because ARM don't have OF support (yet). This patch fixes the problem
by only selecting the OF code on systems with Open Firmware support.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Compile-Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus. This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.
The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.
The ehci and ohci blocks share a common clocking and PHY
infrastructure. Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.
Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.
The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1382) changes the USB_EHCI_TT_NEWSCHED Kconfig option to
be non-experimental and to default to Y. This option has existed for
a long time, and I have not heard any complaints concerning it. By
contrast, several people have reported that their devices could be
made to work only by enabling the option.
The point of changing the default is to cause the option to be enabled
by distros that simply use the default settings for esoteric things
like this.
This change was motivated by Bugzilla #15649.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OMAP systems, we have two different OHCI controllers. The legacy
one is present in OMAP1/2 chips, and the newer one comes bundled as
a companion to the EHCI controller on OMAP3 and newer chips.
We may have multi-omap configurations where OMAP2 and OMAP3
support may be enabled in the same kernel, and need a mechanism
to keep both drivers around.
This patch adds a Kconfig entry for each of these drivers.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.
This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: Julie Zhu <julie.zhu@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ehci support for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We could just make the USB_OHCI_HCD_PPC_OF option implicit
and selected only if at least one of USB_OHCI_HCD_PPC_OF_BE
and USB_OHCI_HCD_PPC_OF_LE are set.
[ dbrownell@users.sourceforge.net: fix patch manglation and dependencies ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sh7724 processor has two on-chip r8a66597 blocks, so add
it to the list of processors for SUPERH_ON_CHIP_R8A66597.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While it looks like xhci was written with both PCI and non-PCI in mind,
apparently only the former has seen any testing. xhci-mem.o can be "fixed"
with a linux/dmapool.h include, but there are still parts of the code that
make use of struct pci_dev directly. So, at least more work is needed before
this can be turned on for non-PCI builds:
CC drivers/usb/host/xhci-mem.o
drivers/usb/host/xhci-mem.c: In function 'xhci_segment_alloc':
drivers/usb/host/xhci-mem.c:45: error: implicit declaration of function 'dma_pool_alloc'
drivers/usb/host/xhci-mem.c:45: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c: In function 'xhci_segment_free':
drivers/usb/host/xhci-mem.c:67: error: implicit declaration of function 'dma_pool_free'
drivers/usb/host/xhci-mem.c: In function 'xhci_alloc_virt_device':
drivers/usb/host/xhci-mem.c:239: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c:248: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c: In function 'xhci_mem_cleanup':
drivers/usb/host/xhci-mem.c:578: error: implicit declaration of function 'dma_pool_destroy'
drivers/usb/host/xhci-mem.c: In function 'xhci_mem_init':
drivers/usb/host/xhci-mem.c:657: error: implicit declaration of function 'dma_pool_create'
drivers/usb/host/xhci-mem.c:658: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c:663: warning: assignment makes pointer from integer without a cast
make[3]: *** [drivers/usb/host/xhci-mem.o] Error 1
CC drivers/usb/host/xhci-pci.o
drivers/usb/host/xhci-pci.c: In function 'xhci_pci_reinit':
drivers/usb/host/xhci-pci.c:39: error: implicit declaration of function 'pci_set_mwi'
drivers/usb/host/xhci-pci.c: At top level:
drivers/usb/host/xhci-pci.c:151: error: 'usb_hcd_pci_probe' undeclared here (not in a function)
drivers/usb/host/xhci-pci.c:152: error: 'usb_hcd_pci_remove' undeclared here (not in a function)
drivers/usb/host/xhci-pci.c:155: error: 'usb_hcd_pci_shutdown' undeclared here (not in a function)
drivers/usb/host/xhci-pci.c:159: warning: function declaration isn't a prototype
drivers/usb/host/xhci-pci.c:164: warning: function declaration isn't a prototype
make[3]: *** [drivers/usb/host/xhci-pci.o] Error 1
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Makefile and Kconfig entries for the xHCI host controller driver.
List Sarah Sharp as the maintainer for the xHCI driver.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the driver only supports PCI and PPC_OF but there are
boards like ARM RealView where this is a platform device. The patch adds
the necessary functions and registration to the isp1760-if.c file and
modifies the corresponding Makefile and Kconfig to be able to use this
driver even if PCI and PPC_OF are not enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove old comments about USB_EHCI_HCD.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> > drivers/built-in.o: In function `ohci_omap_init':
> > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
> > drivers/built-in.o: In function `omap_udc_probe':
> > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
> > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements the support for Oxford OXU210HP USB high-speed host,
no peripheral nor OTG.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: Kan Liu <kan.k.liu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roland Reported the following:
| kmem_cache_create: duplicate cache isp1760_qtd
| Pid: 461, comm: modprobe Tainted: G W 2.6.28-rc2-git3-default #4
| Call Trace:
| [<c017540e>] kmem_cache_create+0xc9/0x3a3
| [<c0159a8d>] free_pages_bulk+0x16c/0x1c9
| [<f165c05f>] isp1760_init+0x0/0xb [isp1760]
| [<f165c018>] init_kmem_once+0x18/0x5f [isp1760]
| [<f165c064>] isp1760_init+0x5/0xb [isp1760]
| [<c010113d>] _stext+0x4d/0x148
| [<c0142936>] load_module+0x12cd/0x142e
| [<c01743c4>] kmem_cache_destroy+0x0/0xd7
| [<c0142b1e>] sys_init_module+0x87/0x176
| [<c01039eb>] sysenter_do_call+0x12/0x2f
The reason, is that ret is initialized with ENODEV instead of 0 _or_
the kmem cache is not freed in error case with no bus binding.
The difference between OF+PCI and OF only is
| 15148 804 32 15984 3e70 isp1760-of-pci.o
| 13748 676 8 14432 3860 isp1760-of.o
about 1.5 KiB.
Until there is a checkbox where the user *must* select atleast one item,
and may select multiple entries I don't make it selectable anymore.
Having a driver which can't be used under any circumstances is broken
anyway and I've seen distros shipping it that way.
Reported-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>a
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: don't rebind drivers after failed resume or reset
USB: fix memory leak in cdc-acm
USB: Unusual dev for Mio moov 330 gps
USB: cdc-wdm: make module autoload work
USB: Fix unneeded endpoint check in pxa27x_udc
usb/gadget: fix kernel-doc warning
USB: Speedtouch: add pre_reset and post_reset routines
USB: usbtest.c: length, sglen and vary are unsigned, so cannot be negative
USB: support Huawei data card product IDs
USB: add ZTE MF626 USB GSM modem entry
USB: storage: Avoid I/O errors when issuing SCSI ioctls to JMicron USB/ATA bridge
USB: Fix debugfs_create_file's error checking method for usb/gadget/s3c2410_udc
USB: ohci: add support for tmio-ohci cell
Some Toshiba Mobile I/O chips have OHCI controller built in.
E.g. the tc6393xb chip found in several Toshiba e-Series PDAs
and in Sharp Zaurus SL-6000 PDA. This adds platform glue
to support OHCI function of the chip.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The UWB stack has some sysfs APIs that will change thus it's best
marked as EXPERIMENTAL until these APIs are finalized.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
A driver for Wireless USB host controllers that comply with the
Wireless Host Controller Interface (HCI) specification as published by
Intel.
The latest publically available version of the specification (0.95) is
supported (except for isochronous transfers).
Build fixes by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
R8A66597 is similar to SH7723 USB 2.0 Host/Function module.
In addition, the USB of SH7366 is compatible with SH7723.
It can support SH7723 USB host by changing Kconfig.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Sparc doesn't have some of the OF interfaces this driver
wants to use.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds HCD support for the Cypress c67x00 family of devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can
support SH7366 USB host by changing several R8A66597 code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to David Brownell, this feature doesn't require an
experimental designation any longer.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts USB_EHCI_FSL config option into the verbose
bool, so we'll able to select it for other freescale processors
with built-in EHCI controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The config symbol for mpc834x processors is CONFIG_PPC_MPC834x,
not CONFIG_MPC834x.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Small updates to the EHCI driver's ISO support:
- Get rid of the Kconfig option for full speed ISO. It may
not be perfect yet, but it hasn't appeared to be dangerous
and pretty much every configuration wants it.
- Instead of two places to disable an empty periodic schedule
after an ISO transfer completes, just have one.
- After the periodic schedule is disabled, we can short-circuit
the schedule scan ... it can't possibly have more work to do.
Assuming a typical config with split iso enabled, the only change
in behavior should be almost unobservable: quicker termination
of periodic scans when the schedule gets emptied.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds device-tree-aware ehci-ppc-of driver.
The code is based on the ehci-ppc-soc driver by
Stefan Roese <sr@denx.de>.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a missing dependency which goofs up the xconfig display.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug introduced by
commit b22817b3c8.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix ssb_ohci_probe() build bug:
drivers/built-in.o: In function `ssb_ohci_probe':
ohci-hcd.c:(.text+0xbff39): undefined reference to `ssb_device_enable'
ohci-hcd.c:(.text+0xbff6f): undefined reference to `ssb_admatch_base'
ohci-hcd.c:(.text+0xbff8b): undefined reference to `ssb_admatch_size'
ohci-hcd.c:(.text+0xbffe5): undefined reference to `ssb_device_disable'
[...]
the reason was that this Kconfig combination was allowed:
CONFIG_SSB=m
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_SSB=y
the fix is to require a modular USB_OHCI_HCD build when SSB is modular.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds SSB bus glue for the USB OHCI HCD.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code. Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC. Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle. Note: this doesn't enable OTG protocol
support.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now select the big-endian configuration options
CONFIG_USB_EHCI_BIG_ENDIAN_MMIO and CONFIG_USB_EHCI_BIG_ENDIAN_DESC in
the usb host Kconfig file and not in the platform Kconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to submit Renesas R8A66597 USB HCD driver.
R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.
This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.
The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.
Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements supports for EHCI controllers whose in-memory
data structures are represented in big-endian format. This is needed
(unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI
spec doesn't specify little-endian format, although that's what most
other implementations use.
The guts of the patch are to introduce the hc32 type and change all
references from le32 to hc32. All access routines are converted from
cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other
"direction". (This is the same approach used with OHCI.)
David fixed:
Whitespace fixes; refresh against ehci cpufreq patch; move glue
for that PPC driver to the patch adding it; fix free symbol
capture bugs in modified "constant" macros; and make "hc32" etc
be "le32" unless we really need the BE options, so "sparse" can
do some real good.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PPC embedded systems can have a ohci controller builtin. In the
new model, it will end up as a driver on the of_platform bus,
this patches takes care of them.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements supports for EHCI controllers whose MMIO
registers are big endian and enables that functionality for
the Toshiba SCC chip. It does _not_ add support for big endian
in-memory data structures as this is not needed for that chip
and I hope it will never be.
The guts of the patch are to convert readl(...) to
ehci_readl(ehci, ...) and similarly for register writes.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch separates support for big endian MMIO register access
and big endian descriptors in order to support the Toshiba SCC
implementation which has big endian registers but little endian
in-memory descriptors.
It simplifies the access functions a bit in ohci.h while at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This "u132-hcd" module is one half of the "driver" for
ELAN's U132 which is a USB to CardBus OHCI controller
adapter. This module needs the "ftdi-elan" module in
order to communicate to CardBus OHCI controller inserted
into the U132 adapter.
When the "ftdi-elan" module detects a supported CardBus
OHCI controller in the U132 adapter it loads this "u132-hcd"
module.
Upon a successful device probe() the single workqueue
is started up which does all the processing of commands
from the USB core that implement the host controller.
The workqueue maintains the urb queues and issues commands
via the functions exported by the "ftdi-elan" module. Each
such command will result in a callback.
Note that the "ftdi-elan" module is a USB client driver.
Note that this "u132-hcd" module is a (cut-down OHCI)
host controller.
Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/Kconfig:87:warning: 'select' used by config symbol 'USB_OHCI_HCD' refer to undefined symbol 'I2C_PNX'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
inlined is the patch that adds basic support for USB OHCI controller
support for PNX4008 Philips PNX4008 ARM board. Due to HW design, it
depends on I2C driver for PNX4008 which I've recetnly posted to LKML and
i2c at lm-sensors.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch removes wrong default for USB_ISP116X_HCD, USB_SL811_HCD and
USB_SL811_CS.
Signed-off-by: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the EHCI driver by adding an improved scheduler for the
transaction translators, found in USB 2.0 hubs and used for low and
full speed devices.
- adds periodic_tt_usecs() and some helper functions, which does
the same thing that "periodic_usecs" does, except on the other
side of the TT, i.e. it calculates the low/fullspeed bandwidth
usage instead of highspeed.
- adds a tt_available() function which is the new implementation
of what tt_no_collision() does ... while tt_no_collision() ensures
that each TT handles only 1 periodic transfer at a time (a very
pessimistic approach) this version instead tracks bandwidth and
allows each TT to handle as many transfers as will fit on each TT's
downstream bus (closer to best-case).
The new scheduler is selected by a config option, marked as EXPERIMENTAL
so it can be tested (and more broadly reviewed) for a while until it
seems safe to remove the original scheduler.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ALCHEMY: Add EHCI support for AU1200
Updated by removing the OHCI support
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding a Host Mode USB driver for the Freescale 83xx.
This driver supports both the Dual-Role (DR) controller and the
Multi-Port-Host (MPH) controller present in the Freescale MPC8349. It has
been tested with the MPC8349CDS reference system. This driver depends on
platform support code for setting up the pins on the device package in a
manner appropriate for the board in use. Note that this patch requires
selecting the EHCI controller option under the USB Host menu.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch with a few tiny fixups for the EHCI Kconfig help
text. Please consider applying.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.
The driver:
- is relatively small, meant for use on embedded platforms.
- runs usbtests 1-14 without problems for days.
- has been in use by 6-7 different people on ARM and PPC platforms,
running a range of devices including USB hubs.
- supports suspend/resume of both the platform device and the root hub;
supports remote wakeup of the root hub (but NOT the platform device)
by USB devices.
- does NOT support ISO transfers (nobody has asked for them).
- is PIO-only.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for a CF-card USB Host adapter, the Ratoc REX-CFU1U, by
wrapping a PCMCIA driver around the existing "sl811-hcd" platform driver.
This CF card is especially useful for PDAs, which currently tend to have
no other solution for USB host capability.
From: Botond Botyanszki <boti@rocketmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Greg Kroah-Hartman